2016 Chevrolet Impala Owners Manual

If the shoulder belt is locked and tightened around a child’s neck, the only way to loosen the belt is to cut it. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, and tighten the belt behind the child restraint after the child restraint has been installed.

Caution

Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments.

(Continued)

Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat.

If you need to secure more than one child restraint in the rear seat, see Where to Put the Restraint 0 87. You cannot secure three child restraints using the LATCH anchors in the rear seat at the same time, but you can install two of them. If you want to do this, install one LATCH child restraint in the right rear seating position, and install the other one either in the left rear seating position or in the center seating position. If you need to install child restraints in both the center and left rear seating positions, the one in the center seating position will need to be secured using the vehicle safety belts instead of the LATCH anchors.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

92

Seats and Restraints

Refer to the following illustration to learn which anchors to use.

There are five lower LATCH anchors in the rear seat. . Use anchors 1 and 2 when

installing a child restraint using LATCH in the right rear seating position.

. Use anchors 3 and 4 when

installing a child restraint using LATCH in the center rear seating position.

. Use anchors 4 and 5 when

installing a child restraint using LATCH in left rear seating position.

Installing child restraints using LATCH in the center and left rear seating positions at the same time is prohibited. Make sure to attach the child restraint at the proper anchor location. This system is designed to make installation of child restraints easier. When using lower anchors, do not use the vehicle's safety belts. Instead use the vehicle's anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether. 1. Attach and tighten the lower

attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to the child restraint manufacturer instructions and the instructions in this manual.

1.1. Find the lower anchors for

the desired seating position.

1.2. For outboard rear seating

positions, put the head restraint in the upright position. See Head Restraints 0 53.

1.3. Put the child restraint on

the seat.

1.4. Attach and tighten the

lower attachments on the child restraint to the lower anchors.

If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. Open the cover to expose the anchor.

2.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

2.2. Route, attach, and tighten the top tether according to the child restraint instructions and the following instructions:

If the position you are using does not have a head restraint and you are using a single tether, route the tether over the seatback.

Seats and Restraints

93

the tether under the head restraint and in between the head restraint posts.

If the position you are using does not have a head restraint and you are using a dual tether, route the tether over the seatback.

If the position you are using has an adjustable head restraint and you are using a single tether, route

If the position you are using has an adjustable head restraint and you are using a dual tether, route the tether under the head restraint and around the head restraint posts.

3. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the LATCH path and attempt to move it side to side and back and forth. There should be no more than 2.5 cm (1 in) of movement for proper installation.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

94

Seats and Restraints

Replacing LATCH System Parts After a Crash { Warning

A crash can damage the LATCH system in the vehicle. A damaged LATCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash. To help make sure the LATCH system is working properly after a crash, see your dealer to have the system inspected and any necessary replacements made as soon as possible.

If the vehicle has the LATCH system and it was being used during a crash, new LATCH system parts may be needed. New parts and repairs may be necessary even if the LATCH system was not being used at the time of the crash.

Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) 0 88 for how and where to install the child restraint using LATCH. If a child restraint is secured in the vehicle using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) 0 88 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.

In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. If the child restraint or vehicle seat position does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint 0 87. 1. Put the child restraint on

the seat.

2. Pick up the latch plate, and run

the lap and shoulder portions of the vehicle safety belt through or around the restraint. The child restraint instructions will show you how.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Seats and Restraints

95

3. Push the latch plate into the

4. Pull the shoulder belt all the

buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.

way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.

5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 4 and 5.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

96

6.

Seats and Restraints

If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) 0 88 for more information.

7. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.

To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it.

Securing Child Restraints (Front Passenger Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint 0 87. In addition, the vehicle has a passenger sensing system which is designed to turn off the front outboard passenger frontal airbag and knee airbag under certain conditions. See Passenger Sensing System 0 75 and Passenger Airbag Status Indicator 0 118 for more information, including important safety information. Never put a rear-facing child seat in the front. This is because the risk to the rear-facing child is so great, if the airbag deploys.

{ Warning

A child in a rear-facing child restraint can be seriously injured or killed if the front outboard passenger frontal airbag inflates.

(Continued)

Warning (Continued)

This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the front outboard passenger frontal airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the front outboard passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the front seat, always move the

(Continued)

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Seats and Restraints

97

Warning (Continued)

front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System 0 75 for additional information.

If the child restraint uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) 0 88 for top tether anchor locations. Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.

When using the lap-shoulder belt to secure the child restraint in this position, follow the instructions that came with the child restraint and the following instructions: 1. Move the seat as far back as it

will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the front outboard passenger frontal airbag and knee airbag, the off indicator on the passenger airbag status indicator should light and stay lit when you start the vehicle. See Passenger Airbag Status Indicator 0 118.

2. Put the child restraint on

the seat.

3. Pick up the latch plate, and run

the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.

Tilt the latch plate to adjust the belt if needed.

4. Push the latch plate into the

buckle until it clicks.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

98

Seats and Restraints

Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.

5. Pull the shoulder belt all the

way out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.

6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 5 and 6.

7. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.

If the airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator Is Lit for a Child Restraint” under Passenger Sensing System 0 75. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Storage

99

Storage

Storage Compartments

Storage Compartments . . . . . . . . 99
Instrument Panel Storage . . . . . . 99
Glove Box . . . . . . . . . . . . . . . . . . . . 100
Cupholders . . . . . . . . . . . . . . . . . . . 100
Center Console Storage . . . . . . 100
Umbrella Storage . . . . . . . . . . . . . 101

Additional Storage Features

Cargo Management

System . . . . . . . . . . . . . . . . . . . . . . 101
Convenience Net . . . . . . . . . . . . . 102

Storage Compartments { Warning

Do not store heavy or sharp objects in storage compartments. In a crash, these objects may cause the cover to open and could result in injury.

Instrument Panel Storage

If equipped with storage behind the fuse box, push on the cover and release to open.

If equipped with storage behind the radio, press P and hold to open. There is a USB port inside. See USB Port 0 164. Press P and hold again to close.

Caution

To avoid damage, do not manually force the display to move.

Keep the storage area closed when not in use.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

100

Storage

The storage area cannot be operated with P when valet mode is enabled. See “Valet Mode” under “Setting Vehicle Preferences” in Home Page 0 158.

Glove Box

Pull the handle up to open.

Cupholders

Center Console Storage

Pull the rear seat armrest down to access.

Push the cover down and release to access. To close, push the cover again and release. There is an accessory power outlet inside.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Umbrella Storage

Storage

101

Additional Storage Features

Cargo Management System

Press the button and lift to access. There is a removable tray on the top of the console. There is an auxiliary input jack, USB port, and accessory power outlet inside. If equipped, there may be an additional USB port and an SD card reader inside. The rear of the center console has a storage area and an accessory power outlet. See Power Outlets 0 108, Auxiliary Jack 0 167, and USB Port 0 164. If equipped with uplevel auxiliary players, see the infotainment manual.

Slide an umbrella into the opening on the driver or passenger door.

There is storage under the load floor for small items. Pull the load floor handle to access. Secure the load floor handle to seal the access to the spare tire.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

102

Storage

Convenience Net

The vehicle may have a convenience net in the trunk. The net (1) attaches to the convenience net hooks (2). Put small loads behind the net. Do not use the net for heavy loads.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

103

Instruments and Controls

Controls

Steering Wheel Adjustment . . . 104
Steering Wheel Controls . . . . . . 105
Heated Steering Wheel . . . . . . . 105
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Windshield Wiper/Washer . . . . 106
Compass . . . . . . . . . . . . . . . . . . . . . 107
Clock (Base Radio) . . . . . . . . . . . 107
Clock (Uplevel Radio) . . . . . . . . 108
Power Outlets . . . . . . . . . . . . . . . . 108
Wireless Charging . . . . . . . . . . . . 109

Warning Lights, Gauges, and Indicators

Warning Lights, Gauges, and

Indicators . . . . . . . . . . . . . . . . . . . . 111
Instrument Cluster . . . . . . . . . . . . 112
Speedometer . . . . . . . . . . . . . . . . . 115
Odometer . . . . . . . . . . . . . . . . . . . . . 115
Trip Odometer . . . . . . . . . . . . . . . . 115
Tachometer . . . . . . . . . . . . . . . . . . . 115
Fuel Gauge . . . . . . . . . . . . . . . . . . . 116
Engine Coolant Temperature

Gauge . . . . . . . . . . . . . . . . . . . . . . 117
Safety Belt Reminders . . . . . . . . 117
Airbag Readiness Light . . . . . . . 118

Passenger Airbag Status

Indicator . . . . . . . . . . . . . . . . . . . . . 118
Charging System Light . . . . . . . 119
Malfunction Indicator Lamp

(Check Engine Light) . . . . . . . . 120

Brake System Warning

Light . . . . . . . . . . . . . . . . . . . . . . . . 121

Electric Parking Brake

Light . . . . . . . . . . . . . . . . . . . . . . . . 122

Service Electric Parking Brake

Light . . . . . . . . . . . . . . . . . . . . . . . . 122

Antilock Brake System (ABS)

Warning Light . . . . . . . . . . . . . . . 123

Lane Departure Warning

(LDW) Light . . . . . . . . . . . . . . . . . 123
Vehicle Ahead Indicator . . . . . . 123
Traction Off Light . . . . . . . . . . . . . 124
StabiliTrak® OFF Light . . . . . . . . 124
Traction Control System (TCS)/

StabiliTrak® Light . . . . . . . . . . . 124
Tire Pressure Light . . . . . . . . . . . 125
Engine Oil Pressure Light . . . . 125
Low Fuel Warning Light . . . . . . 125
Security Light . . . . . . . . . . . . . . . . . 126
High-Beam On Light . . . . . . . . . . 126
Lamps On Reminder . . . . . . . . . 126
Cruise Control Light . . . . . . . . . . 126
Door Ajar Light . . . . . . . . . . . . . . . 127

Information Displays

Driver Information

Center (DIC) . . . . . . . . . . . . . . . . 127

Vehicle Messages

Vehicle Messages . . . . . . . . . . . . 129
Battery Voltage and Charging

Messages . . . . . . . . . . . . . . . . . . . 130
Brake System Messages . . . . . 130
Compass Messages . . . . . . . . . . 130
Cruise Control Messages . . . . . 131
Door Ajar Messages . . . . . . . . . . 131
Engine Cooling System

Messages . . . . . . . . . . . . . . . . . . . 132
Engine Oil Messages . . . . . . . . . 132
Engine Power Messages . . . . . 133
Fuel System Messages . . . . . . . 133
Key and Lock Messages . . . . . 133
Lamp Messages . . . . . . . . . . . . . . 134
Object Detection System

Messages . . . . . . . . . . . . . . . . . . . 134

Ride Control System

Messages . . . . . . . . . . . . . . . . . . . 136
Airbag System Messages . . . . 136
Security Messages . . . . . . . . . . . 136
Service Vehicle Messages . . . . 136
Starting the Vehicle

Messages . . . . . . . . . . . . . . . . . . . 136
Tire Messages . . . . . . . . . . . . . . . . 137
Transmission Messages . . . . . . 137

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

104

Instruments and Controls

Vehicle Reminder

Messages . . . . . . . . . . . . . . . . . . . 137
Vehicle Speed Messages . . . . . 138
Washer Fluid Messages . . . . . . 138
Window Messages . . . . . . . . . . . 138

Vehicle Personalization

Vehicle Personalization . . . . . . . 138

Universal Remote System

Controls

Steering Wheel Adjustment

Universal Remote System . . . . 144
Universal Remote System

Programming . . . . . . . . . . . . . . . 144

Universal Remote System

Operation . . . . . . . . . . . . . . . . . . . 147

To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up

or down.

3. Pull or push the steering wheel

closer or away from you.

4. Pull the lever up to lock the

steering wheel in place.

Power Tilt and Telescoping Wheel

If equipped with this feature, press the control to move the steering wheel up and down or forward and rearward. Do not adjust the steering wheel while driving.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Steering Wheel Controls

Instruments and Controls

105

Heated Steering Wheel

The favorite and volume switches are on the back of the steering wheel. 1. Favorites: Press to select the next or previous favorite when listening to AM, FM, or SiriusXM® (if equipped), or the next or previous track when listening to a media source.

2. Volume: Press to increase or

decrease the volume.

Some audio controls can be adjusted at the steering wheel. g (Talk) : For vehicles with OnStar® or a Bluetooth® system, press to interact with those systems. See OnStar Overview 0 355 or “Bluetooth (Overview)” in the infotainment manual. c (Phone/Mute) : Press to reject an incoming call, or end a current call. Press to mute or unmute the infotainment system when not on a call.

( (Heated Steering Wheel) : For vehicles with a heated steering wheel, press to turn on or off. A light on the button displays when the feature is turned on. The steering wheel takes about three minutes to start heating.

Horn Press a on the steering wheel pad to sound the horn.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

106

Instruments and Controls

Windshield Wiper/Washer

The windshield wiper/washer lever is on the right side of the steering column. With the ignition in ACC/ ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. HI : Use for fast wipes. LO : Use for slow wipes.

INT (Intermittent Wipes) : Move the lever up to INT for intermittent wipes, then turn the x INT band up for more frequent wipes or down for less frequent wipes. OFF : Use to turn the wipers off. 1X (Mist) : For a single wipe, briefly move the wiper lever down. For several wipes, hold the wiper lever down. n L(Windshield Washer) : Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the wipers. The wipers will continue until the lever is released or the maximum wash time is reached. When the windshield wiper lever is released, additional wipes may occur depending on how long the windshield washer had been activated. See Washer Fluid 0 265
for information on filling the windshield washer fluid reservoir.

{ Warning

In freezing weather, do not use the washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.

Clear snow and ice from the wiper blades and windshield before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged blades should be replaced. See Wiper Blade Replacement 0 270. Heavy snow or ice can overload the wiper motor.

Wiper Parking If the ignition is turned to LOCK/ OFF while the wipers are on LO, HI, or INT, they will immediately stop. If the windshield wiper lever is then moved to off before the driver door is opened or within 10 minutes, the wipers will restart and move to the base of the windshield.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

107

If the ignition is turned to LOCK/ OFF while the wipers are performing wipes due to windshield washing, the wipers continue to run until they reach the base of the windshield.

Compass The vehicle may have a compass display on the Driver Information Center (DIC). The compass receives its heading and other information from the Global Positioning System (GPS) antenna, StabiliTrak®, and vehicle speed information. The compass system is designed to operate for a certain number of miles or degrees of turn before needing a signal from the GPS satellites. When the compass display shows CAL, drive the vehicle for a short distance in an open area where it can receive a GPS signal. The compass system will automatically determine when a GPS signal is restored and provide a heading again. See Compass

Messages 0 130 for the messages that may be displayed for the compass.

Clock (Base Radio)

Setting the Time and Date To set the time or date: 1. Select SETTINGS from the

Home Page, then select Time and Date Settings.

2. Select the desired function. 3. Turn the MENU knob to

increase or decrease the value. 4. Press the MENU knob to go to

the next value. After the last value is selected the system will update and return to the SETTINGS menu. Press q BACK to go to the last menu and save the changes.

To set the Auto Set: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select Auto Set.

3. Press the faceplate button just

below Auto Set to turn it on or off.

Press q BACK to go to the last menu and save the changes. Auto Set requires an OnStar subscription. If Auto Set is on, the time displayed on the clock may not update immediately when driving into a new time zone. To set the clock display: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select Clock Display. 3. Turn the MENU knob to Off

or On.

4. Press the MENU knob to

select.

Press q BACK to go to the last menu and save the changes.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

108

Instruments and Controls

Clock (Uplevel Radio)

Power Outlets

Setting the Time and Date To set the time or date: 1. Select Settings from the Home

Page, then select Time and Date Settings.

2. Select the desired function. To set the time or date, press « or ª to change the hour, minutes, AM, or PM. To change the 12-24Hr setting, press the 12-24Hr button. To turn Auto Set on and off, press the Auto Set screen button. Auto Set requires an OnStar subscription. If Auto Set is on, the time displayed on the clock may not update immediately when driving into a new time zone. Press q BACK to go to the last menu and save the changes or { to return to the Home Page.

Power Outlets 12 Volt Direct Current The accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player. There are three accessory power outlets:

Inside the front storage area below the climate control system. Inside the center console. . On the rear of the center

console.

The outlet is powered when the ignition is in ON/RUN or ACC/ ACCESSORY, or until the driver door is opened within 10 minutes of turning off the vehicle. See Retained Accessory Power (RAP) 0 208. Open the protective cover to use the accessory power outlet.

Certain electrical accessories may not be compatible with the accessory power outlets and could overload vehicle or adapter fuses. If there is a problem, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Add-On Electrical Equipment 0 246.

Caution

Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 amps rating.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Power Outlet 110/120 Volt Alternating Current The vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts.

The power outlet is on the rear of the center console. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected.

Instruments and Controls

109

The indicator light does not come on if the ignition is in LOCK/OFF; if no equipment is plugged into the outlet; or if the equipment is plugged in, but not fully seated in the outlet. If equipment is connected using more than 150 watts or a system fault is detected, the equipment may operate briefly then turn off. A protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Retained Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) 0 208. The power restarts when equipment using 150 watts or less is plugged into the outlet and a system fault is not detected. The power outlet is not designed for and may not work properly, if the following are plugged in: . Equipment with high initial peak

wattage, such as compressor-driven refrigerators and electric power tools.

. Other equipment requiring an

extremely stable power supply, such as microcomputer-controlled electric blankets or touch sensor lamps.

. Medical equipment.

Wireless Charging The vehicle may have wireless charging in the storage bin under the radio. See Center Console Storage 0 100. The system wirelessly charges one PMA or Qi compatible mobile device. To check for phone or other device compatibility, see www.gmtotalconnect.com. { Warning

Wireless charging can affect the operation of an implanted pacemaker or other medical devices. If you have one, it is recommended to consult with your doctor before using the wireless charging system.

3. The ~ will display on the V

on the infotainment screen. This indicates that the mobile device is properly positioned and charging. If a phone is placed on the charging pad and ~ does not display, remove the phone from the pad, and wait three seconds before placing/aligning the phone on the pad again.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

110

Instruments and Controls

The vehicle must be in ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP). The wireless charging feature may not correctly indicate charging when the vehicle is in RAP. See Retained Accessory Power (RAP) 0 208. The operating temperature is -20 °C (-4 °F) to 60 °C (140 °F) for the charging system and 0 °C (32 °F) to 35 °C (95 °F) for the phone. { Warning

Remove all metal objects from the charging pad before charging your mobile device. Metal objects, such as coins, keys, rings, or paper clips, between the phone and charging pad will become very hot. On the rare occasion that the charging system does not detect a metal object, and the object gets wedged between the phone and charger, remove the phone and allow the metallic object to cool before removing it from the charging pad, to prevent burns.

To charge a mobile device: 1. Remove all objects from the

charging pad. The system may not charge if there are any objects on the charging pad. 2. Place the mobile device face up on the @ symbol on the charging pad.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

111

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Some warning lights come on briefly when the engine is started to indicate they are working. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Waiting to do repairs can be costly and even dangerous.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

112

Instruments and Controls

Instrument Cluster

English Shown, Metric Similar

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

113

English Stop/Start Shown, Metric Similar

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

114

Instruments and Controls

Cluster Menu There is an interactive display area in the center of the instrument cluster.

Info app. This is where you can view the selected Driver Information Center (DIC) displays. See Driver Information Center (DIC) 0 127.

. Audio . Phone . Navigation . Settings

Audio In the main view of the Audio app, press w or x to scroll through radio stations or move to the next/ previous track of a CD/USB/ Bluetooth device that is connected to the vehicle. Press V to select the Audio app, then press p to enter the Audio menu. In the Audio menu browse for music, select from the favorites, or change the audio source.

Phone

Press V to select the Phone app, then press p to enter the Phone menu. In the Phone menu, if there is

Use the right steering wheel control to open and scroll through the different items and displays. Press o to access the cluster applications. Use w or x to scroll through the list of available applications. Not all applications will be available on all vehicles.

no active phone call, view recent calls, scroll through contacts, or select from the favorites. If there is an active call, mute or unmute the phone or switch to handset or handsfree operation.

Navigation

Press V to select the Navigation app, then press p to enter the Navigation menu. If there is no active route, you can resume the last route, location details, and turn the voice prompts on/off. If there is an active route, press V to cancel route guidance or turn the voice prompts on/off.

Settings

Press V to select the Settings app. Use w or x to scroll through the items in the Settings menu. Units : Press p while Units is displayed to enter the Units menu. Choose English or metric units by pressing V while the desired item is highlighted.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

115

Info Pages : Press p while Info Pages is displayed to enter the Info Pages menu and select the items to be displayed in the Info App. See Driver Information Center (DIC) 0 127. Speed Warning : The Speed Warning display allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press p when Speed Warning is displayed. Press w or x to adjust the value. Press V to set the speed. Once the speed is set, this feature can be turned off by pressing V while viewing this page. If the selected speed limit is exceeded, a pop-up warning is displayed with a chime. Compass : In certain vehicles the compass setting will allow for manually setting the compass. The user can set the zone and calibrate the compass. This setting page is only available on vehicles that are equipped with Remote Compass Module.

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles.

Trip Odometer The trip odometer shows how far the vehicle has been driven since the trip odometer was last reset. The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) 0 127.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). For vehicles with the Stop/Start system, when the ignition is in ON/ RUN, the tachometer indicates the

vehicle status. When pointing to AUTO STOP, the engine is off but the vehicle is on and can move. The engine could auto start at any time. When the indicator points to OFF, the vehicle is off. When the engine is on, the tachometer will indicate the engine’s revolutions per minute (rpm). The tachometer may vary by several hundred rpm’s, during auto stop mode, when the engine is shutting off and restarting. A slight bump may be felt when the transmission is determining the most fuel efficient operating range.

Caution

If the engine is operated with the rpm’s in the warning area at the high end of the tachometer, the vehicle could be damaged, and the damage would not be covered by the vehicle warranty. Do not operate the engine with the rpm’s in the warning area.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

116

Instruments and Controls

Fuel Gauge

Metric

English

When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There is still a little fuel left, but the fuel tank should be filled soon. Here are four things that some owners ask about. None of these show a problem with the fuel gauge:

. At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. . The gauge moves a little while

turning a corner or speeding up. . The gauge takes a few seconds

to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Engine Coolant Temperature Gauge

Instruments and Controls

117

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

Metric

English

This gauge shows the engine coolant temperature. If the gauge pointer moves toward the shaded area, the engine is too hot. This reading indicates the same thing as the warning light. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible. See Engine Overheating 0 264 for more information.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

118

Instruments and Controls

Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System 0 75.

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag,

grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System 0 69.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages 0 136.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System 0 75 for important safety information. The passenger airbag status indicator is in the overhead console.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

119

outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light 0 118 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages 0 130.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or the on or off symbol, to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

120

Instruments and Controls

If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp (Check Engine Light) This light is part of the vehicle’s emission control on-board diagnostic system. If this light is on while the engine is running, a malfunction has been detected and the vehicle may require service. The light should come on to show that it is working when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access. See Ignition Positions (Keyless Access) 0 201 or Ignition Positions (Key Access) 0 203.

Malfunctions are often indicated by the system before any problem is noticeable. Being aware of the light and seeking service promptly when it comes on may prevent damage.

Caution

If the vehicle is driven continually with this light on, the emission control system may not work as well, the fuel economy may be lower, and the vehicle may not run smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Caution

Modifications to the engine, transmission, exhaust, intake, or fuel system, or the use of replacement tires that do not meet the original tire specifications, can cause this light to come on. This could lead to

(Continued)

Caution (Continued)

costly repairs not covered by the vehicle warranty. This could also affect the vehicle’s ability to pass an Emissions Inspection/ Maintenance test. See Accessories and Modifications 0 249.

If the light is flashing : A malfunction has been detected that could damage the emission control system and increase vehicle emissions. Diagnosis and service may be required. To help prevent damage, reduce vehicle speed and avoid hard accelerations and uphill grades. If towing a trailer, reduce the amount of cargo being hauled as soon as possible. If the light continues to flash, find a safe place to park. Turn the vehicle off and wait at least 10 seconds before restarting the engine. If the light is still flashing, follow the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

previous guidelines and see your dealer for service as soon as possible. If the light is on steady : A malfunction has been detected. Diagnosis and service may be required. Check the following: . A loose or missing fuel cap may cause the light to come on. See Filling the Tank 0 239. A few driving trips with the cap properly installed may turn the light off.

. Poor fuel quality can cause

inefficient engine operation and poor driveability, which may go away once the engine is warmed up. If this occurs, change the fuel brand. It may require at least one full tank of the proper fuel to turn the light off. See Fuel 0 237.

If the light remains on, see your dealer.

Instruments and Controls

121

Emissions Inspection and Maintenance Programs If the vehicle requires an Emissions Inspection/Maintenance test, the test equipment will likely connect to the vehicle's Data Link Connector (DLC).

The DLC is under the instrument panel to the left of the steering wheel. Connecting devices that are not used to perform an Emissions Inspection/Maintenance test or to service the vehicle may affect vehicle operation See Add-On Electrical Equipment 0 246. See your dealer if assistance is needed. The vehicle may not pass inspection if: . The light is on when the engine

is running.

. The light does not come on

when the ignition is in ON/RUN with the engine not running for Key Access or in Service Only Mode for Keyless Access.

. Critical emission control systems

have not been completely diagnosed. If this happens, the vehicle would not be ready for inspection and might require several days of routine driving before the system is ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down, or if the vehicle has been recently serviced.

See your dealer if the vehicle will not pass or cannot be made ready for the test.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

122

Instruments and Controls

vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

This light comes on briefly when the vehicle is turned on. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. If the light comes on and stays on, there is a brake problem. { Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system

(Continued)

Warning (Continued)

warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Electric Parking Brake Light

Metric

English

This light comes on when the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the Electric Parking Brake system or another system. A message may also display in the Driver Information Center (DIC). See Brake System Messages 0 130.

If the light does not come on, or remains flashing, see your dealer.

Service Electric Parking Brake Light

This light should come on briefly when starting the vehicle. If it does not come on, have it fixed so it will be ready to warn if there is a problem. If this light stays on, there is a problem with the Electric Parking Brake system or another system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See the information for the Electric Parking Brake under Parking Brake 0 214.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

123

If a message displays in the Driver Information Center (DIC), see Brake System Messages 0 130.

Antilock Brake System (ABS) Warning Light

This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady.

If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning. If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light 0 121 and Brake System Messages 0 130.

Lane Departure Warning (LDW) Light

If equipped, this light comes on briefly while starting the vehicle. If it does not come on, have the vehicle serviced.

This light is green if LDW is on and ready to operate. This light changes to amber and flashes to indicate that the lane marking has been crossed without using a turn signal in that direction. See Lane Departure Warning (LDW) 0 235.

Vehicle Ahead Indicator

If equipped, this indicator will display green when a vehicle is detected ahead and amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System 0 230.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

124

Instruments and Controls

Traction Off Light

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control 0 216.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control 0 216.

Traction Control System (TCS)/StabiliTrak® Light

This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control 0 216.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

125

Tire Pressure Light

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages 0 137. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure 0 290.

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation 0 293.

Engine Oil Pressure Light

Caution

Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil low can also damage the engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

126

Instruments and Controls

It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.

Security Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) 0 43 or Immobilizer Operation (Keyless Access) 0 44.

High-Beam On Light

Cruise Control Light

This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer 0 149.

Lamps On Reminder

This light in the Driver Information Center (DIC) is white when the cruise control is on and ready, and turns green when the cruise control is set and active. See Cruise Control 0 218. Adaptive Cruise Control Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls 0 148.

This light in the Driver Information Center (DIC) is white when the Adaptive Cruise Control (ACC) (if equipped) is on and ready, and

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

Instruments and Controls

127

turns green when the ACC is set and active. See Adaptive Cruise Control 0 220.

Door Ajar Light

This light comes on in the Driver Information Center (DIC) when a door is open or not securely latched. Before driving, check that all doors are properly closed.

Information Displays

Driver Information Center (DIC) The DIC displays are shown in the center of the instrument cluster in the Info app. See Instrument Cluster 0 112. The Info app is only available when the vehicle is in ON/RUN. The displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.

w or x : Press to move up or down in a list, or on the main view press to cycle through the different Info app pages. o or p : Press o to open application menus on the left. Press p to open interaction menus on the right. V (Select/Reset) : Press to select a menu item. Press and hold to reset values on certain screens, or on the main view reset info pages to the original setting. DIC Info Page Options The info pages on the DIC can be turned on or off through the Settings app. 1. Press o to access the cluster

applications.

2. Press w or x to scroll to the

Settings application.

3. Press V to select the

Settings app.

4. Scroll to Info Pages and

press p.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S/Canada-9086448) - 2016 - CRC - 5/20/15

128

Instruments and Controls

5. Select Edit List. 6. Press w or x to move

through the list of possible information displays.

7. Press V while an item is

highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.

DIC Info Pages The following is the list of all possible DIC info page displays. Some may not be available for your particular vehicle. Some items may not be turned on by default but can be turned on through the Settings app. See “DIC Info Page Options” earlier in this section. Current Speed : Displays the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip A and Average Fuel Economy or Trip B and Average Fuel Economy : The Trip display shows the current distance traveled, in

either kilometers (km) or miles (mi), since the trip odometer was last reset. The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the approximate average fuel economy that the vehicle has right now, and will change as driving conditions change. This number is calculated based on the number of L/ 100 km (mpg) recorded since the last time this menu item was reset. The Average Fuel Economy and trip odometer can be reset together by pressing and holding V while this display is active. Fuel Range : Displays the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.

Average Speed : Displays the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing and holding V while this display is active.

Timer : To start the timer, press V while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press V briefly while this display is active and the timer is running. To reset the timer to zero, press and hold V while this display is active.