2015 Chevrolet Impala Owners Manual

NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle. REMOTE LEFT IN VEHICLE This message displays when leaving the vehicle with the RKE transmitter still inside. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the RKE transmitter needs to be replaced.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (33,1)

Instruments and Controls

5-33

USE TRANSMITTER POCKET TO START This message displays when the transmitter needs to be placed in the transmitter pocket to start the vehicle. See “Starting the Vehicle with a Low Transmitter Battery or Wireless Interference” under Remote Keyless Entry (RKE) System Operation on page 2-3.

Lamp Messages

AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the automatic light control has been turned on or off. See Automatic Headlamp System on page 6-2. XX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10-26 and Replacement Bulbs on page 10-30.

TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Object Detection System Messages

AUTOMATIC COLLISION PREP OFF This message displays when the Active Emergency Braking System has been turned off. See Active Emergency Braking System on page 9-48. AUTOMATIC COLLISION PREP REDUCED This message displays when the Active Emergency Braking System has been set to the Alert setting. This setting disables most Active Emergency Braking functions. Some last-second automatic braking capability is still provided with the Alert setting, but braking is less

likely to occur. See Active Emergency Braking System on page 9-48. AUTOMATIC COLLISION PREP UNAVAILABLE This message displays when the Active Emergency Braking System has been unavailable for some time. The Active Emergency Braking System does not need service. This can occur under the following conditions:

The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10-72.

. Heavy rain or snow is interfering with the radar object detection or camera performance.

This message may also be displayed if there is a problem with the StabiliTrak system.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (34,1)

5-34

Instruments and Controls

FORWARD COLLISION ALERT OFF This message displays when the Forward Collision Alert has been turned off. FRONT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well. LANE DEPARTURE WARNING UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service.

This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. PARK ASSIST OFF This message displays when the Parking Assist system has been turned off or when there is a temporary condition causing the system to be disabled. REAR CROSS TRAFFIC ALERT OFF This message displays when the Rear Cross Traffic Alert has been turned off. SERVICE AUTOMATIC COLLISION PREP If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and/or the Active Emergency

Braking System may not work. Do not use these systems until the vehicle has been repaired. SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARKING ASSIST This message displays if there is a problem with the Parking Assist system. Do not use this system to help you park. See your dealer for service. SERVICE SIDE DETECTION SYSTEM If this message remains on after continued driving, the vehicle needs service. Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) features will not work. Take the vehicle to your dealer.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (35,1)

Instruments and Controls

5-35

SHIFT TO PARK BEFORE EXITING This message may display if Adaptive Cruise Control (ACC) is engaged holding the vehicle at a stop, and the driver attempts to exit the vehicle. Put the vehicle in P (Park) before exiting. SIDE BLIND ZONE ALERT OFF This message indicates that the driver has turned the Side Blind Zone Alert (SBZA) system off. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) are disabled either because the sensor is blocked and cannot detect vehicles in the blind zone, or the vehicle is passing through an open area, such as the desert, where there is insufficient data for operation. This message may also activate during heavy rain or due to road spray. The vehicle does not

need service. For cleaning, see "Washing the Vehicle" under Exterior Care on page 10-72.

Ride Control System Messages

SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE POWER STEERING This message is displayed if there is a problem with the power steering system and a chime may sound. Take the vehicle to your dealer for service. SERVICE VEHICLE SOON This message is displayed if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (36,1)

5-36

Instruments and Controls

Starting the Vehicle Messages

PRESS BRAKE TO START VEHICLE This message is displayed when attempting to start the vehicle without first pressing the brake pedal. SERVICE KEYLESS START SYSTEM This message is displayed if there is a problem with the pushbutton start system. Take the vehicle to your dealer for service.

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10-48.

TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10-48. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-23. If a tire pressure message displays, inflate the tires until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10-38, Vehicle Load Limits on page 9-10, and Tire Pressure on page 10-45. More than one tire pressure message can be received at a time. The DIC also shows the tire

pressure values. See Driver Information Center (DIC) on page 5-26.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when using the Driver Shift Control (DSC) and attempting to shift to a gear not appropriate for the vehicle speed and engine revolutions per minute (rpm). See Manual Mode on page 9-27. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when turning the ignition off if the vehicle is not in P (Park).

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (37,1)

Instruments and Controls

5-37

TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message is displayed when ice conditions are possible. TURN WIPER CONTROL TO INTERMITTENT FIRST This message is displayed when attempting to adjust the intermittent wiper speed without intermittent

selected on the wiper control. See Windshield Wiper/Washer on page 5-4.

Vehicle Speed Messages

SPEED LIMIT EXCEEDED This message is displayed when the vehicle speed is greater than the speed warning speed. See "Speed Warning" under Instrument Cluster on page 5-9. SPEED LIMIT SET TO XXX This message is displayed when the speed warning is set. See "Speed Warning" under Instrument Cluster on page 5-9.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message may display when the washer fluid level is low. Fill the windshield washer reservoir as soon

as possible. See Engine Compartment Overview on page 10-5 for the location of the windshield washer reservoir. Also, see Washer Fluid on page 10-19.

Window Messages

OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to program each front window for the express-up feature to work. See Power Windows on page 2-22.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (38,1)

5-38

Instruments and Controls

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features.

Base Radio Audio System Controls To access the personalization menus: 1. On the Home page, turn the

MENU knob to highlight Settings and press the MENU knob.

2. Turn the MENU knob to highlight

the desired feature and press the MENU knob to display a list of available options.

3. Turn the MENU knob to scroll

through and highlight the desired option, then press the MENU knob.

4. Turn the MENU knob to highlight

the desired option setting and press the MENU knob.

5. Press q BACK to return to the

previous menu.

Uplevel Radio Audio System Controls To access the personalization menus: 1. Press SETTINGS on the Home

page on the infotainment system display.

2. Press the desired feature to

display a list of available options.

3. Press the desired option. 4. Press to select the desired

option setting.

5. Press q BACK to return to the

previous menu.

Personalization Menus The following list of features may be available:

Time and Date Language (Language)

. Valet Mode . Radio . Vehicle . Bluetooth . Voice . Display . Rear Camera . Return to Factory Settings . Software Information Each menu is detailed in the following information. Time and Date Manually set the time and date. See Clock (Base Radio) on page 5-5 or Clock (Uplevel Radio) on page 5-6. Language (Language) Select Language, then select from the available language(s).

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (39,1)

Valet Mode To turn valet mode on and off, see “Valet Mode” under “Setting Radio Preferences” in Home Page on page 7-4. Radio To manage the radio features, see “Radio Setup” under “Setting Radio Preferences” in Home Page on page 7-4. Vehicle Select and the following may display: . Climate and Air Quality . Collision/Detection Systems . Comfort and Convenience

Lighting

. Power Door Locks . Remote Lock, Unlock, Start

Instruments and Controls

5-39

Climate and Air Quality Select and the following may display: . Auto Fan Max Speed . Air Conditioning Mode . Auto Defog . Auto Rear Defog

Auto Fan Max Speed This feature will set the maximum auto fan speed. Select Low, Medium, or High.

Air Conditioning Mode This feature changes the mode of the air conditioning. Select Off, On, or Last Setting.

Auto Defog When set to On, the front defog will automatically react to temperature and humidity conditions that may cause fogging. Only vehicles with the dual automatic climate control will have this option.

Select Off or On.

Auto Rear Defog If equipped, this allows the Auto Rear Defog to be turned on or off. This feature will automatically turn on the rear window defogger when it is cold outside. Select Off or On.

Collision/Detection Systems Select and the following may display: . Auto Collision Preparation . Go Notifier . Side Blind Zone Alert . Rear Cross Traffic Alert

Auto Collision Preparation This feature will turn on or off the Forward Collision Alert feature as well as the Automatic Braking capability of the Auto Collision Preparation feature. With the Alert and Brake setting, both Forward Collision Alert as well as the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (40,1)

5-40

Instruments and Controls

Automatic Braking capability of the Auto Collision Preparation feature are available. The Alert setting disables most automatic braking functions of the Auto Collision Preparation feature. Some last-second automatic braking capability is still provided with the Alert setting, but it is much less likely to be triggered by most driving conditions. Off disables all Forward Collision Alert and Automatic Braking capabilities of the Auto Collision Preparation feature. Select Off, Alert and Brake, or Alert. See Driver Assistance Systems on page 9-43.

Go Notifier This feature will give a reminder that Adaptive Cruise Control provides when it has brought the vehicle to a complete stop behind another stopping vehicle, and then that vehicle drives on. Select Off or On.

See Active Emergency Braking System on page 9-48.

Side Blind Zone Alert This allows the feature to be turned on or off. Select Off or On. See Side Blind Zone Alert (SBZA) on page 9-50.

Rear Cross Traffic Alert This allows the feature to be turned on or off. Select Off or On. See Driver Assistance Systems on page 9-43.

Comfort and Convenience Select and the following may display: . Auto Memory Recall . Easy Exit Options . Chime Volume . Reverse Tilt Mirror

Auto Memory Recall This feature automatically recalls the current driver’s previously stored 1 or 2 button positions when entering the vehicle. See Memory Seats on page 3-7. Select Off, On - Driver Door Open, or On - At ignition On.

Easy Exit Options This feature automatically recalls the current driver’s previously stored Exit button position when exiting the vehicle. See Memory Seats on page 3-7. Select Off or On.

Chime Volume This allows the selection of the chime volume level. Press + or − to adjust the volume.

Reverse Tilt Mirror When on, both the driver and passenger, driver, or passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (41,1)

improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse) or the ignition is turned to OFF. Select Off, On - Driver and Passenger, On - Driver, or On - Passenger.

Lighting Select and the following may display: . Vehicle Locator Lights . Exit Lighting . Daytime Tail Lights

Vehicle Locator Lights This feature will flash the exterior lamps when K on the Remote Keyless Entry (RKE) transmitter is pressed to locate the vehicle. Select Off or On.

Instruments and Controls

5-41

Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Select Off, 30 Seconds, 60
Seconds, or 120 Seconds.

Daytime Tail Lights This feature allows the taillamps to be on during the day. Select Off or On.

Power Door Locks Select and the following may display: . Unlocked Door Anti-Lockout . Auto Door Unlock . Delayed Door Lock

Unlocked Door Anti-Lockout When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available.

Select Off or On.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Select Off, All Doors, or Driver Door.

Delayed Door Lock When on, this feature will delay the locking of the doors. To override the delay, press the power door lock switch on the door. Select Off or On.

Remote Lock, Unlock, Start Select and the following may display: . Remote Unlock Light Feedback . Remote Lock Feedback . Remote Door Unlock . Remote Start Auto Cool Seats . Remote Start Auto Heat Seats . Passive Door Unlock . Passive Door Lock

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (42,1)

5-42

Instruments and Controls

. Remote Left in Vehicle Alert

Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Select Off or Flash Lights.

Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Select Off, Lights and Horn, Lights Only, or Horn Only.

Remote Door Unlock This allows selection of which doors will unlock when pressing K on the RKE transmitter. Select All Doors or Driver Door.

Remote Start Auto Cool Seats If equipped and turned on, this feature will turn the ventilated seats on when using remote start on warm days. Select Off or On.

Remote Start Auto Heat Seats If equipped and turned on, this feature will turn the heated seats on when using remote start on cold days. Select Off or On.

Passive Door Unlock This allows the selection of what doors will unlock when using the button on the driver door to unlock the vehicle. Select All Doors or Driver Door.

Passive Door Lock This feature can be turned on or off, or can be used to select feedback when using the button on the driver door to lock the vehicle. See Remote Keyless Entry (RKE) System Operation on page 2-3. Select Off, On with Horn Chirp, or On.

Remote Left in Vehicle Alert This feature sounds an alert when the RKE transmitter is left in the vehicle. Select Off or On. Bluetooth Select and the following may display: . Pair New Device . Device Management . Ringtones . Voice Mail Numbers

Pair New Device Select to pair a new device. See “Pairing” under Bluetooth (Voice Recognition) on page 7-21 or Bluetooth (Overview) on page 7-19
or Bluetooth (Infotainment Controls - Base Radio) on page 7-26 or “Pairing” under “Bluetooth” in the infotainment manual.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (43,1)

Instruments and Controls

5-43

Device Management Select to connect to a different phone source, disconnect a phone, or delete a phone.

Ringtones Press to change the ring tone for the specific phone. The phone does not need to be connected to change the ring.

Voice Mail Numbers This feature displays the voice mail number for all connected phones. To change the voice mail number, select EDIT or press the EDIT button. Type a new number, then select SAVE or press the SAVE button. Voice Select and the following may display: . Prompt Length . Audio Feedback Speed

Prompt Length This feature adjusts the voice prompt length. Select Short or Long.

Audio Feedback Speed This feature adjusts the audio feedback speed. Select Slow, Medium, or Fast. Display Select and the following may display:

Theme

. Mode . Calibrate Touchscreen

Turn Display Off

Theme Select to change the color, font, and art of the display. Select Contemporary, Mainstreet, Edge, or Velocity.

Mode Select to change the display screen for day or night driving. Select Auto, Day, or Night.

Calibrate Touchscreen Select to calibrate the touchscreen, then follow the prompts.

Turn Display Off Select to turn the display off. Press anywhere on the display area or any faceplate button to turn the display on. Rear Camera Select and the following may display: . Guidance Lines . Rear Cross Traffic Alert . Rear Park Assist Symbols

Guidance Lines Select to turn Off or On. See Assistance Systems for Parking or Backing on page 9-44.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (44,1)

5-44

Instruments and Controls

Rear Cross Traffic Alert Select to turn Off or On. See Assistance Systems for Parking or Backing on page 9-44.

Rear Park Assist Symbols Select to turn Off or On. See Assistance Systems for Parking or Backing on page 9-44. Return to Factory Settings Select and the following may display: . Restore Vehicle Settings . Clear All Private Data . Restore Radio Settings

Restore Vehicle Settings This allows vehicle settings to be restored. Select Restore or Cancel.

Clear All Private Data This allows all private information from the vehicle to be cleared. Select Delete or Cancel.

Restore Radio Settings This allows radio settings to be restored. Select Restore or Cancel. Software Information Select to view the infotainment system current software information.

Universal Remote System See Radio Frequency Statement on page 13-12.

Universal Remote System Programming

If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (45,1)

home automation devices. These instructions refer to a garage door opener, but can be used for other devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section.

Instruments and Controls

5-45

To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door. Make sure the hand-held transmitter has a new battery for quick and accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons with the indicator light in view. The

hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.

2. At the same time, press and

hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2
with the procedure under in “Radio Signals for Canada and Some Gate Operators” later in this section.

3. Press and hold the newly

programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.

If the indicator light stays on continuously or the garage door moves when the

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (46,1)

5-46

Instruments and Controls

button is pressed, then programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.

does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.

The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons. Radio Signals for Canada and Some Gate Operators For questions or programming help call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long

Learn or Smart Button

4. After completing Steps 1–3 ,

locate the Learn or Smart button inside garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.

5. Press and release the Learn or

6.

Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds and then release it. If the garage door does not move or the lamp on the garage door opener receiver

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (47,1)

Instruments and Controls

5-47

enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the

buttons. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (48,1)

5-48

Instruments and Controls

2 NOTES

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lighting

Exterior Lamp Controls

Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off

Reminder . . . . . . . . . . . . . . . . . . . . 6-1

Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-1
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-2

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-2
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-3

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-4
Courtesy Lamps . . . . . . . . . . . . . . 6-4
Dome Lamps . . . . . . . . . . . . . . . . . 6-4
Reading Lamps . . . . . . . . . . . . . . . 6-5

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-5
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-6
Battery Load Management . . . . 6-6

The exterior lamp control is on the turn signal lever. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode. In Canada, the headlamps and Daytime Running Lamps (DRL) will automatically reactivate when the vehicle is shifted out of P (Park).

Lighting

6-1

AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps including all lamps, except the headlamps. 2 (Headlamps): Turns on the headlamps together with the parking lamps and instrument panel lights.

Exterior Lamps Off Reminder A warning chime sounds if the driver door is opened while the ignition is off and the exterior lamps are on.

Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer): Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (2,1)

6-2

Lighting

This indicator light turns on in the instrument cluster when the high-beam headlamps are on.

Flash-to-Pass To flash the high beams, pull the turn signal lever toward you, and release.

Daytime Running Lamps (DRL) DRL can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada.

The DRL system turns on the low-beam headlamps at a reduced brightness. For vehicles with High Intensity Discharge (HID) headlamps, there is a dedicated DRL. The DRL will come on when all of the following conditions are met:

The ignition is on. The exterior lamp control is in AUTO. The light sensor determines it is daytime. The vehicle is not in P (Park).

When the DRL are on, the taillamps, sidemarker lamps, instrument panel lights, and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off.

This vehicle may have a DRL disabling function. When the DRL are on and a turn signal is activated, the DRL on that side will be off until the turn signal goes off.

Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (3,1)

There is a light sensor on top of the instrument panel. Do not cover the sensor, otherwise the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel. When it is bright enough outside, the headlamps will turn off or may change to Daytime Running Lamps (DRL). The automatic headlamp system turns off when the exterior lamp control is turned to O or the ignition is off. Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are

Lighting

6-3

Turn and Lane-Change Signals

not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.

Hazard Warning Flashers

Move the lever all the way up or down to signal a turn. An arrow on the instrument cluster flashes in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times.

| (Hazard Warning Flashers): Press this button to make the front and rear turn signal lamps flash on and off. Press again to turn the flashers off. The hazard warning flashers turn on automatically if the airbags deploy.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (4,1)

6-4

Lighting

The turn and lane-change signal can be turned off manually by moving the lever back to its original position. If after signaling a turn or lane change, the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have any burned out bulbs replaced. If a bulb is not burned out, check the fuse. See Fuses on page 10-31.

Interior Lighting

Dome Lamps

Instrument Panel Illumination Control

The brightness of the instrument panel lighting and steering wheel controls can be adjusted. D (Instrument Panel Illumination): Move the thumbwheel up or down to brighten or dim the lights.

Courtesy Lamps The courtesy lamps come on when any door is opened and the dome lamp is in the DOOR position.

The interior lamps control in the overhead console controls both the front and rear interior lamps. To change the dome lamp settings, press the following: OFF: Turns the lamp off, even when a door is open. DOOR: The lamp comes on automatically when a door is opened. ON: Turns the lamp on.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (5,1)

Reading Lamps

There are front and rear reading lamps in the overhead console and the headliner. # or $ (Reading Lamps): Press the button near each lamp to turn it on or off.

Front Reading Lamps

Rear Reading Lamps

Lighting

6-5

Lighting Features

Entry Lighting The headlamps, taillamps, license plate lamps, back-up lamps, dome lamps, and most of the interior lights turn on briefly when the Remote Keyless Entry (RKE) transmitter K button is pressed. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16. After about 30 seconds the exterior lamps turn off, then the dome lamps and remaining interior lights dim to off. Entry lighting can be disabled manually by changing the ignition out of the OFF position, or by pressing the RKE transmitter Q button. This feature can be changed. See Vehicle Personalization on page 5-38.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (6,1)

6-6

Lighting

Exit Lighting The headlamps, taillamps, back-up lamps, parking lamps, and license plate lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamps also come on when the key is removed from the ignition. The exterior lamps and dome lamps remain on after the door is closed for a set amount of time, then automatically turn off. If equipped with Keyless Access, the exterior lamps and dome lamps automatically turn on when the driver door is opened after the ignition is turned off. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16. The exterior lamps turn off immediately by turning the exterior lamp control off. This feature can be changed. See Vehicle Personalization on page 5-38.

Battery Load Management The vehicle has Electric Power Management (EPM), which estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.

A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed and it is recommended that the driver reduce the electrical loads as much as possible. See Battery Voltage and Charging Messages on page 5-29.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (1,1)

Phone

Bluetooth (Overview) . . . . . . . . 7-19
Bluetooth (Voice

Recognition) . . . . . . . . . . . . . . . 7-21

Bluetooth (Infotainment

Controls - Base Radio) . . . . . 7-26

Trademarks and License Agreements

Trademarks and License

Agreements . . . . . . . . . . . . . . . . 7-31

Infotainment System

Introduction

Infotainment . . . . . . . . . . . . . . . . . . . 7-1
Theft-Deterrent Feature . . . . . . . 7-2
Overview . . . . . . . . . . . . . . . . . . . . . . 7-3
Home Page . . . . . . . . . . . . . . . . . . . 7-4
Software Updates . . . . . . . . . . . . . 7-7

Radio

AM-FM Radio . . . . . . . . . . . . . . . . . 7-7
Satellite Radio . . . . . . . . . . . . . . . . 7-9
Radio Reception . . . . . . . . . . . . . 7-10
Backglass Antenna . . . . . . . . . . 7-10
Multi-Band Antenna . . . . . . . . . . 7-11

Audio Players

CD Player . . . . . . . . . . . . . . . . . . . . 7-11
USB Port . . . . . . . . . . . . . . . . . . . . 7-14
SD Card Reader . . . . . . . . . . . . . 7-17
Auxiliary Jack . . . . . . . . . . . . . . . . 7-17

Navigation

OnStar® System . . . . . . . . . . . . . 7-18

Infotainment System 7-1

Introduction

Infotainment Base radio information is included in this manual. See the infotainment manual for information on other available infotainment systems. Read the following pages to become familiar with these features.

{ Warning

Taking your eyes off the road for too long or too often while using any infotainment feature can cause a crash. You or others could be injured or killed. Do not give extended attention to infotainment tasks while driving. Limit your glances at the vehicle displays and focus your attention on driving. Use voice commands whenever possible.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (2,1)

To play the infotainment system with the ignition off, see Retained Accessory Power (RAP) on page 9-22.

Theft-Deterrent Feature TheftLock® is designed to discourage theft of the vehicle's radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle.

7-2

Infotainment System

The infotainment system has built-in features intended to help avoid distraction by disabling some functions when driving. These functions may gray out when they are unavailable. Many infotainment features are also available through the instrument cluster and steering wheel controls. Before driving: . Become familiar with the

operation, faceplate buttons, and screen buttons.

. Set up the audio by presetting

favorite stations, setting the tone, and adjusting the speakers.

. Set up phone numbers in

advance so they can be called easily by pressing a single button or by using a single voice command if equipped with Bluetooth phone capability.

See Defensive Driving on page 9-3.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (3,1)

Overview

Infotainment System Overview The infotainment system is controlled by using the buttons on the faceplate and steering wheel controls. See Steering Wheel Controls on page 5-3.

1. q (Favorite Pages)

2. Buttons 1–5

Press to scroll backward through the favorite pages.

Press to select favorite stations.

Infotainment System 7-3

Press and hold to save favorite stations. Press to select options.

3. r (Favorite Pages)

Press to scroll forward through the favorite pages.

4. O (Power/Volume)

Press to turn the audio on. Press and hold to turn it off. When on, press to mute the system. Press again to unmute. Turn to increase or decrease the volume.

5. MEDIA

Press to change the audio source between CD, USB, SD Card, and AUX.

6. RADIO

Press to change the audio source between AM, FM, or SiriusXM, if equipped.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (4,1)

7-4

Infotainment System

7. TONE

Press to open the Tone Settings menu.

8. g or l (Seek)

Press g to seek to the beginning of the current or previous track. If the track has been playing for less than five seconds, it seeks the previous track. If longer than five seconds, the current track starts from the beginning. Press g and hold to quickly reverse through a track. Release the button to return to playing speed. Press l to seek the next track. Press l and hold to fast forward through a track. Release the button to return to playing speed. See CD Player on page 7-11.

For AM, FM, or SiriusXM (if equipped), press l to seek to the next strong station.

9. { (Home Page)

Press to go to the Home Page from anywhere in the system. See “Home Page” following.

10. q BACK

Press to return to the previous screen in a menu.

11. CD Slot 12. MENU

Press to access the menu for the current audio source. Press to select the highlighted menu option. Turn to scroll through a list. Turn to manually select a station.

13. X (Eject)

Press to eject the CD.

Home Page

Home Page Features The infotainment system displays a Home Page that makes it easy to access all of the applications. Turn the MENU knob to highlight application icons. Press the MENU knob to access the feature’s options. Various functions are disabled when the vehicle is moving. AUDIO: Select the AUDIO screen icon to display the active source page. The sources available are AM, FM, SiriusXM® (if equipped), CD, USB/iPod, AUX, and SD Card Reader. See AM-FM Radio on page 7-7, Satellite Radio on page 7-9, CD Player on page 7-11, and Auxiliary Jack on page 7-17.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (5,1)

PHONE: Select the PHONE screen icon to display the Phone main page. See Bluetooth (Voice Recognition) on page 7-21 or Bluetooth (Overview) on page 7-19
or Bluetooth (Infotainment Controls - Base Radio) on page 7-26. NAV: Select the NAV screen icon to display the last Turn-by-Turn maneuver if a destination was downloaded. See Navigation on page 14-3. SETTINGS: Select the SETTINGS screen icon to display the Settings main page. See “Setting Radio Preferences” following. Setting Radio Preferences Select the SETTINGS screen icon to display the Settings menu and the following may display: Time: See Clock (Base Radio) on page 5-5 or Clock (Uplevel Radio) on page 5-6. Language (Language): This will set the display language in the radio and instrument cluster. Select to

display a list of languages. Select q BACK to go back to the previous menu. Valet Mode: Type a four-digit code on the circular numeric keypad: 1. Turn the MENU knob to highlight

a number.

2. Press the MENU knob to select

it. Do this for each one of the four digits. Select Enter to go to the confirmation screen.

3. Re-enter the four-digit code.

Select LOCK to lock the system. This will also lock out access to the storage behind the radio, if equipped. See Instrument Panel Storage on page 4-1.

4. Type the four-digit code to

unlock the system. Select q BACK to go back to the previous menu.

Radio: See “Radio Setup” later in this section.

Infotainment System 7-5

Vehicle: See Vehicle Personalization on page 5-38. Display: Press the MENU knob to turn the display on or off. Return to Factory Settings: See “Return to Factory Settings” later in this section.

Radio Setup From the RADIO/BAND screen icon, the following may be displayed: Manage Favorites:

Turn the MENU knob and press to select a favorite.

To delete a favorite, press the button just below the DELETE screen button. To move a favorite, press the MOVE screen button. Turn the MENU knob to select a new location, then press the DROP screen button to select the new location.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (6,1)

7-6

Infotainment System

. Select q BACK to go back to the

previous menu.

Number of Favorites Shown: To set the number of favorites for display, select Auto to automatically adjust the number of Favorites pages shown as Favorites are added and removed. Another way to adjust is to select a number from 5– 25 to show that selection of favorites. Audible Touch Feedback: Select Audible Touch Feedback to turn feedback off or on. Auto Volume (If Equipped): This feature adjusts the volume based on vehicle speed. The options are Off, Low, Medium-Low, Medium, Medium-High, or High. Select the desired volume. DSP Modes (If Equipped): This feature has four modes: . Normal: Adjusts the audio to

normal mode. This provides the best sound quality for all seating positions.

. Driver: Adjusts the audio to give

the driver the best possible sound quality.

. Rear: Adjusts the audio to give

the rear seat occupants the best possible sound quality.

. Centerpoint®: Turns on Bose

Centerpoint surround technology.

Centerpoint creates a surround sound from nearly any audio source: existing CD collection, satellite radio, and audio players. Maximum Startup Volume: This feature sets the maximum startup volume. If the vehicle is started and the volume is greater than this level, the volume is adjusted to this level. To set the maximum startup volume, Turn the MENU knob to increase or decrease startup volume.

Rear Camera (If Equipped) From the Rear Camera screen button, the following may be displayed: Rear Park Assist Symbols: This feature will display symbols where objects are detected by the Rear Parking Assist system. Select Park Assist Symbols, then select Off or On. See Assistance Systems for Parking or Backing on page 9-44. Rear Cross Traffic Alert: This feature will display an alert icon when cross traffic is detected. Select Rear Cross Traffic Alert, then select Off or On.

Return to Factory Settings Select Return to Factory Settings and the following list may display: Restore Vehicle Settings: This option will restore factory vehicle personalization settings. Select Restore Vehicle Settings. A screen displays stating all vehicle

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (7,1)

Software Updates See the website for more information. In the U.S., see www.chevrolet.com In Canada, see www.chevrolet.gm.ca

customization settings will be restored to the factory settings. Select Cancel or Continue. Clear All Private Data: This option clears all private information from the vehicle. Select Clear All Private Data. Select Cancel or Continue. Restore Radio Settings: This option will restore factory radio settings. Select Restore Radio Settings. A screen displays stating all personalized radio settings will be restored back to the factory settings. Select Cancel or Continue. English and Metric Unit Conversion To change the display units between English and metric units, see “Units” under “Settings” in Instrument Cluster on page 5-9.

Infotainment System 7-7

Radio

AM-FM Radio

Playing the Radio While on the audio main page, press the RADIO or MEDIA button repeatedly to display and scroll through the available sources: AM, FM, and SiriusXM® (if equipped), CD, USB, SD, and AUX. The steering wheel controls can also be used to adjust the volume. See Steering Wheel Controls on page 5-3.

AM, FM, SiriusXM (If Equipped) To select AM, FM, or SiriusXM (if equipped): 1. Press {. 2. Turn the MENU knob to highlight

the AUDIO screen icon.

3. Press the MENU knob to select.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (8,1)

7-8

Infotainment System

4. Turn the MENU knob to highlight

either AM, FM, or SiriusXM (if equipped) and press MENU to select.

Press the RADIO faceplate button to display and change the radio source. Press the MENU knob and the following radio settings may display: Tone Settings: . Bass, Midrange, and Treble:

Turn the MENU knob to highlight. Press the MENU knob to select. Turn the MENU knob to adjust.

. Balance: Turn the MENU knob

to highlight. Press the MENU knob to select. Turn the MENU knob left for more sound from the left speakers or right for more sound from the right speakers. The middle position balances the sound between the left and right speakers.

Fade: Turn the MENU knob to highlight. Press the MENU knob to select. Turn the MENU knob to the left for more sound from the front speakers and to the right for more sound from the rear speakers. The middle position balances the sound between the front and rear speakers.

. EQ (Equalizer): Turn the MENU

knob to highlight. Turn the MENU knob to scroll through the options. Press the MENU knob to select. Press q BACK button to go to the previous menu.

If equipped, this

Station List: Select to display a list of AM or FM stations. Press q BACK to go to the previous menu. Auto Volume: feature adjusts the volume based on the vehicle speed. Select the level between off, low, medium-low, medium, medium-high, and high. Press q BACK to go to the previous menu.

EQ (Equalizer) Settings: If equipped with a Bose Sound System, the available choices are Manual and Talk. DSP Modes: If equipped with a Bose Surround Sound System, it will have the following four DSP Modes: . Normal: Adjusts the audio to

normal mode. This provides the best sound quality for all seating positions.

. Driver: Adjusts the audio to give

the driver the best possible sound quality.

. Rear: Adjusts the audio to give

the rear seat occupants the best possible sound quality.

. Centerpoint®: Turns on Bose

Centerpoint® surround technology.

Centerpoint creates a surround sound from nearly any audio source: existing CD collection, satellite radio, and audio players.

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (9,1)

Options for SiriusXM Only XM View: XM view allows the channel list to be viewed by channel name, artist playing on channel, or song playing on channel. Select to display Channel List in XM views. Turn the MENU knob to highlight and press the MENU knob to select. Press q BACK to go to the previous menu. Channel List: Select to display a list of SiriusXM channels. Turn the MENU knob to highlight and press the MENU knob to select. Press q BACK to go to the previous menu. Also see the radio settings common for all sources earlier in this section. Finding a Station

Seeking a Station Press g or l to search for the previous or next strongest station, or press and hold to quickly search through stations.

Tuning a Station Turn the MENU knob to manually find a station. Storing Radio Station Presets Up to 25 preset stations from all bands can be stored in the favorite lists in any order. Up to five stations can be stored in each favorite page and the number of favorites can be set. AM, FM, or SiriusXM (If Equipped): While on the active source main page, such as AM, FM, and SiriusXM (if equipped), press and hold the corresponding key. Mixed-Audio Favorites Favorites can be stored including radio stations. To display the favorites page, press q or r on the radio faceplate. From the Settings menu, press the MENU knob to select Manage Favorites. The Manage Favorites feature has the option of moving or

Infotainment System 7-9

deleting a favorite. See “Manage Favorites” under Overview on page 7-3.

Satellite Radio

SiriusXM® Satellite Radio Service Vehicles with a SiriusXM satellite radio tuner and a valid SiriusXM satellite radio subscription can receive SiriusXM programming. SiriusXM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces. SiriusXM satellite radio has a wide variety of programming and commercial-free music, coast to coast, and in digital-quality sound. A service fee is required to receive the SiriusXM service. See www.siriusxmradio.com or call 1-866-635-2349 (U.S.); or see www.xmradio.ca or call 1-877-209-0079 (Canada).

Chevrolet Impala Owner Manual (GMNA-Localizing-U.S./Canada-7576026) - 2015 - CRC 1st Edition - 4/2/14

Black plate (10,1)

7-10

Infotainment System

When SiriusXM is active, the channel name and number, category name, song title, and artist display on the screen. Browsing SiriusXM Channels To browse the SiriusXM channels: