2005 Chevrolet Impala Owners Manual

Download PDF Manual
PARK (P) only when your vehicle is stopped. Starting Your 3400 V6 Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine warms up. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If the engine does not start in 10 seconds, push the accelerator pedal about one-quarter of the way down while you turn the key to START. Do this until the engine starts. As soon as it does, let go of the key. 2-17 2. If it does not start within 10 seconds, hold your key in START for about 10 seconds at a time until your engine starts. Wait about 15 seconds between each try. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. If the vehicle starts brieﬂy but then stops again, do the same thing. This time keep the pedal down for ﬁve or six seconds to clear the extra gasoline from the engine. After waiting about 15 seconds, repeat the normal starting procedure. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. 3. If your engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for a maximum of 15 seconds. This clears the extra gasoline from the engine. If the engine still will not start or starts brieﬂy but then stops again, repeat Step 1 or 2, depending on temperature. When the engine starts, release the key and the accelerator pedal. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Starting Your 3800 Series II V6 Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2-18 Engine Coolant Heater Your vehicle may be equipped with this feature. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is attached to the underside of the diagonal brace, which is located above the engine air cleaner/ﬁlter assembly. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. 2-19 Automatic Transaxle Operation Your automatic transaxle may have a shift lever on the steering column or on the console between the seats. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-36. Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) while the ignition is in ON. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P). See Shifting Out of Park (P) on page 2-25. There is also a display, like the graphic above, located on the instrument panel cluster that will indicate the gear the vehicle is in. Maximum engine speed is limited on automatic transaxle vehicles while you are in PARK (P) or NEUTRAL (N) to protect driveline components from improper operation. There are several different positions for your shift lever. PARK (P): This position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. 2-20 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If You Are Stuck: In Sand, Mud, Ice or Snow on page 4-28. NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine racing may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not racing when shifting your vehicle. AUTOMATIC OVERDRIVE X: This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than 35 mph (55 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator pedal all the way down. If your vehicle seems to start up rather You will shift down to the next gear and have more power. Notice: slowly or not shift gears when you go faster, and you continue to drive your vehicle that way, you could damage the transaxle. Have your vehicle serviced right away. You can drive in SECOND (2) when you are driving less than 35 mph (55 km/h) and AUTOMATIC OVERDRIVE X for higher speeds until then. 2-21 THIRD (3): This position is also used for normal driving, but it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE X. Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE X: (cid:127) When driving on hilly, winding roads (cid:127) When towing a trailer, so there is less shifting between gears (cid:127) When going down a steep hill (cid:127) When driving in non-highway scenarios (i.e. city streets, etc.) SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or AUTOMATIC OVERDRIVE X instead of SECOND (2). 2-22 FIRST (1): This position gives you even more power, but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is in FIRST (1), the transaxle will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. Parking Brake The parking brake is located to the left of the brake pedal, near the driver’s door. To set the parking brake, hold the brake pedal down with your right foot. Push down the parking brake pedal with your left foot. To release the parking brake, hold the brake pedal down with your right foot and push the parking brake pedal with your left foot. When you lift your left foot, the parking brake pedal will follow it to the released position. A warning chime will sound if the parking brake is set, the ignition is on and the shift lever is not in PARK (P). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and parking on any hill, see Towing a Trailer on page 4-36. That section shows what to do ﬁrst to keep the trailer from moving. Shifting Into Park (P) {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-23. If you are pulling a trailer, see Towing a Trailer on page 4-36. 2-23 Steering Column Shift Lever 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by pulling the shift lever toward you and moving it up as far as it will go. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Console Shift Lever 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into the PARK (P) position, hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you or if you have the console shift lever, without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked into PARK (P). 2-24 Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-23. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transaxle Operation on page 2-20. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P), being sure to press the shift lever button if you have a console shift. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the ignition key to ACC. 2. Apply and hold the brake pedal down until the end of Step 4. 3. Shift to NEUTRAL (N). 4. Start the engine and shift to the drive gear you want. 5. Have the vehicle ﬁxed as soon as you can. 2-25 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-26 Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-26. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-24. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-23. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer on page 4-36. 2-27 Mirrors Manual Rearview Mirror Adjust all the mirrors so you can see clearly when you are sitting in a comfortable driving position. To reduce glare from headlamps behind you, pull the lever at the bottom of the mirror toward you (to the night position). To return the mirror back to the day position, push the lever away from you. There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. Manual Rearview Mirror with OnStar® If the vehicle has this mirror, it has a lever located at the bottom of the mirror between the two lamps. The lever is used to change the mirror from the day to the night position. To reduce glare from headlamps behind you while driving at night, pull the lever toward you. To return the mirror to the day position, return the lever to its original position. There are two map lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. 2-28 There are also OnStar® buttons located at the bottom of the mirror face. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-30 for more information about the services OnStar® provides. Automatic Dimming Rearview Mirror The vehicle may be equipped with an automatic dimming rearview mirror. Push the center button on the bottom of the mirror to turn this feature on. The mirror will darken gradually to reduce glare from headlamps behind you. This may take a few moments. The mirror will lighten whenever you shift to REVERSE (R). There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. One photocell on the front of the mirror senses when it is becoming dark outside. Another photocell, facing rearward, senses headlamps behind you. To turn the automatic dimming feature off, press the center button again. To keep the photocells operating well, occasionally clean them with a cotton swab and glass cleaner. Automatic Dimming Rearview Mirror with OnStar® The vehicle may have an automatic dimming rearview mirror with the OnStar® System. Press the button located below the mirror, on the far left, for up to three seconds to turn the automatic dimming feature off and on. While turned on, this mirror functions exactly like the automatic dimming mirror described previously. There are two lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. There are also OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-30 for more information about the service OnStar® provides. Outside Power Mirrors The outside power mirror controls are located near the driver’s side window, on the armrest. Use the selector switch located above the four-way control panel to choose either the left or right outside mirror. Then press any of the four arrows located on the control pad to move each mirror in the desired direction. Adjust each mirror so you can see the side of your vehicle and the area beside and behind your vehicle. 2-29 Heated Outside Mirrors If your vehicle has this feature, the surface of the outside mirrors will heat when the rear window defogger is activated. Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information, and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstarcanada.com. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstarcanada.com. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for the ﬁrst year. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs. For more information, press the OnStar® button to speak with an advisor. 2-30 Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability is available if your hand-held cell phone is lost, forgotten, or has a low battery. It is a hands-free wireless phone that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® user’s guide in the vehicle’s glove box or visit www.onstar.com or www.onstarcanada.com; or speak with an OnStar® advisor by pressing the OnStar® button or by calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Virtual Advisor is a feature of OnStar® Personal Calling that uses minutes to access up-to-date weather and traffic reports for your area, news and sports updates, stock quotes, entertainment and more. You are also able to listen and reply to your E-mail through your vehicle’s audio system. Customize your information proﬁle at www.myonstar.com. See the OnStar® user’s guide for more information. 2-31 (cid:127) This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Programming the HomeLink® Transmitter Do not use the HomeLink® Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your HomeLink® Transmitter. HomeLink® Transmitter HomeLink®, a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink® information can be found on the internet at www.homelink.com or by calling 1-800-355-3515. If your vehicle is equipped with the HomeLink® Transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2-32 Read the instructions completely before attempting to program the HomeLink® Transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Keep the original transmitter for use in other vehicles as well as for future HomeLink® programming. It is also recommended that upon the sale of the vehicle, the programmed HomeLink® buttons should be erased for security purposes. Refer to “Erasing HomeLink® Buttons” or, for assistance, contact HomeLink® on the internet at: www.homelink.com or by calling 1-800-355-3515. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio frequency. Programming HomeLink® Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons, releasing only when the indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink® buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the HomeLink® buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired button on HomeLink® and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 2-33 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed HomeLink® button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener (or other rolling code device), repeat this sequence a third time to complete the programming. HomeLink® should now activate your rolling-code equipped device. To program the remaining two HomeLink® buttons, begin with Step 2 of “Programming HomeLink®.” You do not want to repeat Step 1, as this will erase all previous programming. 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after HomeLink® successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained HomeLink® button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink® button is pressed and released. To program the remaining two HomeLink® buttons, begin with Step 2 under “Programming HomeLink®.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device (most commonly, a garage door opener). 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 2-34 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for HomeLink® to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out” in the same manner. If you live in Canada, or you are having difficulty programming a gate operator by using the “Programming HomeLink®” procedures (regardless of where you live), replace Step 3 under “Programming HomeLink®” with the following: Continue to press and hold the HomeLink® button while you press and release every two seconds (cycle) your hand-held transmitter until the frequency signal has been successfully accepted by HomeLink®. The indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming HomeLink®” to complete. Using HomeLink® Press and hold the appropriate HomeLink® button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink® Buttons To erase programming from the three buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. HomeLink® is now in the train (learning) mode and can be programmed at any time beginning with Step 2 under “Programming HomeLink®” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single HomeLink® Button” following this section. 2-35 Reprogramming a Single HomeLink® Button To program a device to HomeLink® using a HomeLink® button previously trained, follow these steps: 1. Press and hold the desired HomeLink® button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the HomeLink® button, proceed with Step 2 under “Programming HomeLink®” shown earlier in this section. Resetting Defaults To reset HomeLink® to default settings do the following: 1. Hold down the two outside buttons for about 20 seconds until the indicator light begins to ﬂash. 2. Continue to hold both buttons until the HomeLink® indicator light turns off. 3. Release both buttons. For questions or comments, contact HomeLink® at 1-800-355-3515, or on the internet at www.homelink.com. Storage Areas Glove Box To open the glove box, lift up on the lever. The glove box has a light inside. Front Storage Area To use the storage area, fold down the armrest located in the center front seat. Press the latch on the front edge and pull up to access the storage area. Center Console Storage Area Your vehicle may be equipped with a center console. It has cupholders and a storage area. To open the console’s storage area, pull up on the latch located in the front of the console lid. Rear Storage Area If your vehicle has the split folding rear seat, there will be two cupholders in the rear seat armrest. To access them, pull down on the cloth strap located toward the top of your center back seat cushion. 2-36 Convenience Net The vehicle may have a convenience net located on the back wall of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over. The net is not for larger, heavier loads. Store those in the trunk as far forward as possible. Unhook the net so that it will lie ﬂat when not in use. Sunroof The vehicle may have a sunroof and a sunshade. The switch is located on the overhead console if the vehicle is equipped with a Driver Information Center (DIC). The switch works only when the ignition is in ACC, ON or when Retained Accessory Power (RAP) is active. Open/Express: To activate the express-open feature, press the switch rearward two times. Press the switch forward to stop movement of the sunroof. Vent: The sunroof also has a vent feature. It can be activated from the closed sunroof position by pressing the switch once rearward. To close, push and hold the sunroof switch forward. When using this feature, the sunshade should be fully opened in the rear position. The sunshade can be opened manually by sliding it rearward, or automatically, by opening the power sunroof. You will need to close the sunshade manually by sliding it forward. Close: To close the sunroof, push the switch forward and hold until the sunroof motor stops, or release the switch when the desired position has been reached. DIC Version Shown If the vehicle is not equipped with a DIC, the sunroof switch is located on the roof panel headliner. 2-37 Vehicle Personalization Some of the convenience features can be reset or customized to perform according to your preference. Features you can program depend upon the options that came with your vehicle. The following list shows features that can be reset or customized along with the options. (cid:127) Settings (Available for All) (cid:127) Engine Oil Life System Reset (Available for All) Low Tire Pressure Reset (If Equipped) (cid:127) Delayed Headlamp Illumination (Available for All) (cid:127) Automatic Door Lock and Unlock (Available for All) (cid:127) Remote Visual Veriﬁcation (Available with Remote Keyless Entry) (cid:127) Remote Audible Veriﬁcation (Available with Remote Keyless Entry) (cid:127) Content Theft Operation (Optional with Content Theft System) Trunk Jamb (Optional with Content Theft System) (cid:127) Horn Chirp On Timer (Available with Remote Keyless Entry) (cid:127) Remote Keyless Entry Transmitter Programming (Available with Remote Keyless Entry) (cid:127) Return to Original Factory Settings (Available for All) (cid:127) Exit Vehicle Customization Mode Programmable Modes To reset or customize the features, ﬁrst enter the vehicle customization main menu. To enter the main menu, do the following: 1. Turn the ignition to ACC or ON. The radio must be off. 2. Press and hold the TUNE or DISP knob on the radio for at least ﬁve seconds until SETTINGS is displayed. 3. Press the SEEK or PSCAN up or down arrows to scroll through each available feature on your main menu. 4. Press the PREV or NEXT buttons to scroll through the lower menu. An asterisk (*) will appear next to the item that is the current setting. The following information shows how to reset or customize features after entering the main menu. 2-38 (cid:127) (cid:127) SETTINGS (Display Current Settings) This feature displays your vehicle personalization settings. OIL LIFE (Engine Oil Life System Reset) This feature allows you to reset the engine oil life system after an oil change. Be careful not to reset the OIL LIFE at any time other than when the oil has been changed. To clear the CHANGE ENGINE OIL light from the instrument panel cluster and reset the engine oil life system, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until OIL LIFE appears on the display. 2. Press the PREV or NEXT button to enter the submenu. RESET will then be displayed. 3. Press the TUNE/DISP knob to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Also see “How to Reset the Engine Oil Life System” under Engine Oil Life System on page 5-21 and Engine Oil on page 5-18 for more information. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-4. The CHANGE ENGINE OIL light is now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. TIRE MON (Tire Inﬂation Monitor Reset) This feature allows you to reset the tire pressure monitor after checking all tire pressures. See Tires on page 5-58. To clear the LOW TIRE PRESSURE light from the instrument panel cluster and reset the low tire pressure monitor, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until TIRE MON appears on the display. 2. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. 3. Press the TUNE/DISP knob to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. The low tire pressure monitor is now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. 2-39 LT DELAY (Delayed Headlamp Illumination) This feature allows the headlamps and parking lamps to stay on for a set amount of time after you exit the vehicle, or to turn off immediately. Programmable Modes Mode 1: OFF Mode 2: 30 SEC Mode 3: 60 SEC Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until LT DELAY appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 2-40 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. AUTOLOCK (Automatic Door Lock and Unlock) With the ignition in ON and the doors closed, this feature allows the vehicle doors to automatically lock and unlock when the driver shifts the transaxle into and out of PARK (P), or to turn the feature off. Programmable Modes Mode 1: OFF Mode 2: LCK ONLY — Automatic door lock on/automatic door unlock off. Mode 3: DRVR UNL — Automatic door lock on/automatic door unlock on (driver’s door only). Mode 4: ALL UNL — Automatic door lock on/automatic door unlock on. Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until AUTOLOCK appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. FOB LIGHT (Remote Visual Veriﬁcation) This feature allows the exterior lights to ﬂash when the remote keyless entry transmitter is used to lock or unlock the vehicle or to program no veriﬁcation. Programmable Modes Mode 1: OFF Mode 2: ON — One ﬂash for each remote lock/two ﬂashes for each remote unlock. Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until FOB LIGHT appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 2-41 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. A new selection will be displayed with an asterisk (*) for one second. If your vehicle has the optional content theft-deterrent system, the ﬁrst time a remote UNLOCK command is received, three ﬂashes will be seen and three horn chirps heard to indicate an alarm condition has occurred since last arming. See Theft-Deterrent Systems on page 2-14. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. 2-42 FOB HORN (Remote Audible Veriﬁcation) This feature allows the horn to chirp when the remote keyless entry transmitter is used to lock or unlock the vehicle or to program no veriﬁcation. Programmable Modes Mode 1: OFF Mode 2: PARTIAL — One chirp for each remote LOCK command/no chirp for remote UNLOCK command. Mode 3: FULL — One chirp for each remote LOCK command/two chirps for the ﬁrst remote UNLOCK command. Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until FOB HORN appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/ DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. If your vehicle has the optional content theft-deterrent system, the ﬁrst time the remote UNLOCK command is received three ﬂashes will be seen and three chirps will be heard to indicate an alarm condition has occurred since last arming. See Theft-Deterrent Systems on page 2-14. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. ALARM (Content Theft Operation) This feature allows the content theft-deterrent system to be turned on or off. Programmable Modes Mode 1: ALRM OFF Mode 2: ALRM ON Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until ALARM appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. 2-43 TRNKJAMB (Trunk Jamb) This feature allows the content theft system trunk lock sensor to be disabled or enabled. Programmable Modes Mode 1: TRNK OFF Mode 2: TRNK ON Your vehicle was originally programmed to Mode 2. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until TRNKJAMB appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. CHIRP (Horn Chirp Timer) This feature allows you to choose between short or long horn chirp sounds when the remote keyless entry transmitter is used. Programmable Modes Mode 1: SHORT Mode 2: LONG Your vehicle was originally programmed to Mode 1. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until CHIRP appears on the display. 2. Press the PREV or NEXT button to enter the submenu. The current selection will have an asterisk (*) next to it. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. 2-44 3. Scroll, using the PREV or NEXT buttons, through the modes to change the current mode. 4. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. ORIG. SET (Return to the Original Settings) This feature allows you to return all feature customization settings back to their original factory settings. To reset, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until ORIG. SET appears on the display. 2. Press the PREV or NEXT button to enter the submenu. SET ALL will appear. 3. With your preference displayed, press the TUNE/DISP button to select. A chime will be heard to verify the new setting. The new selection will be displayed with an asterisk (*) for one second. The original factory settings are now reset. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. FOB PROG (Remote Keyless Entry Transmitter Programming) This feature allows you to match the remote keyless entry transmitter to your vehicle. To match the transmitter, do the following: 1. Scroll, using the SEEK/PSCAN up or down arrows, until FOB PROG appears on the display. 2. Press the PREV or NEXT button to enter the submenu. BEGIN will be displayed. 3. Press the TUNE/DISP button to start programming. When the message PUSH FOB ﬂashes, press and hold the LOCK and UNLOCK buttons on the ﬁrst transmitter at the same time for 15 seconds. A chime will be heard to verify the transmitter is learned. 4. Repeat Step 3 for each additional transmitter. The transmitter is programmed now. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. EXIT (Exit Feature Customization Mode) This feature allows you to exit the vehicle customization programming. To exit, do the following: (cid:127) Scroll until EXIT appears on the display. (cid:127) Press the TUNE/DISP button to exit programming. A chime will be heard to verify the exit. 2-45 ✍ NOTES 2-46 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-9 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Cruise Control ..............................................3-11 Exterior Lamps .............................................3-14 Delayed Headlamps ......................................3-15 Daytime Running Lamps (DRL)/Automatic Headlamp System .....................................3-16 Fog Lamps ..................................................3-16 Instrument Panel Brightness ...........................3-17 Courtesy Lamps ...........................................3-17 Dome Lamp .................................................3-17 Entry Lighting ...............................................3-17 Delayed Entry Lighting ...................................3-18 Delayed Exit Lighting .....................................3-18 Parade Dimming ...........................................3-18 Reading Lamps ............................................3-18 Battery Run-Down Protection ..........................3-19 Accessory Power Outlets ...............................3-19 Ashtrays and Cigarette Lighter ........................3-20 Climate Controls ............................................3-21 Dual Climate Control System ..........................3-21 Outlet Adjustment .........................................3-24 Passenger Compartment Air Filter ...................3-25 Warning Lights, Gages, and Indicators ............3-26 Instrument Panel Cluster ................................3-27 Speedometer and Odometer ...........................3-30 Trip Odometer ..............................................3-30 Tachometer .................................................3-30 Safety Belt Reminder Light .............................3-30 Airbag Readiness Light ..................................3-31 Brake System Warning Light ..........................3-32 Anti-Lock Brake System Warning Light .............3-33 Traction Control System (TCS) Warning Light ...3-33 Engine Coolant Temperature Gage ..................3-34 Malfunction Indicator Lamp .............................3-35 Cruise Control Light ......................................3-38 Highbeam On Light .......................................3-38 Fuel Gage ...................................................3-39 Message Center .............................................3-40 Service Traction System Warning Message ......3-40 Traction Active Message ................................3-41 Battery Warning Message ..............................3-41 3-1 Section 3 Instrument Panel Hot Coolant Temperature Warning Message .....3-42 Low Oil Pressure Message ............................3-42 Low Engine Oil Level Message .......................3-43 Change Engine Oil Message ..........................3-44 Low Tire Message ........................................3-44 Door Ajar Warning Message ...........................3-45 Trunk Ajar Warning Message .........................3-45 Security Message .........................................3-46 Low Washer Fluid Warning Message ...............3-46 Low Fuel Warning Message ...........................3-47 Low Brake Fluid Warning Message .................3-47 Service Vehicle Soon Message .......................3-48 Highbeam Out Warning Message ....................3-48 Driver Information Center (DIC) .......................3-49 Trip Computer ................................................3-51 Audio System(s) .............................................3-52 Setting the Time ...........................................3-52 Radio with Cassette ......................................3-53 Radio with CD ..............................................3-64 Radio with Cassette and CD ..........................3-74 Theft-Deterrent Feature ..................................3-87 Audio Steering Wheel Controls .......................3-87 Radio Reception ...........................................3-88 Care of Your Cassette Tape Player .................3-88 Care of Your CDs .........................................3-90 Care of Your CD Player ................................3-90 Backglass Antenna .......................................3-90 XM™ Satellite Radio Antenna System .............3-91 Vehicle Customization Settings .......................3-91 Chime Level Adjustment ................................3-91 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are listed here: A. Instrument Panel Fuse Block. See Fuses and Circuit Breakers on page 5-95. I. Remote Trunk Release Button. See “Remote Trunk Release” under Trunk on page 2-10. B. Traction Control On/Off Button (If Equipped). See Traction Control System (TCS) on page 4-8. C. Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. Audio Steering Wheel Controls (Option). See Audio Steering Wheel Controls on page 3-87. E. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. F. Audio System. See Audio System(s) on page 3-52. G. Air Vent. See Outlet Adjustment on page 3-24. H. Exterior Lamps Control. See Exterior Lamps on page 3-14. J. Tilt Steering Wheel Lever. See Tilt Wheel on page 3-6. K. Hood Release. See Hood Release on page 5-11. L. Steering Wheel Cruise Control (If Equipped). See Cruise Control on page 3-11. M. Ignition Switch. See Ignition Positions on page 2-16. N. Center Console Shift Lever (If Equipped). See “Console Shift Lever” under Shifting Into Park (P) on page 2-23. O. Climate Controls. See Dual Climate Control System on page 3-21. P. Glove Box. See Glove Box on page 2-36. 3-5 Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place. Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located near the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 Turn Signal/Multifunction Lever Flash-to-Pass. See Flash-to-Pass on page 3-9. (cid:127) Windshield Wipers. See Windshield Wipers on page 3-9. (cid:127) Windshield Washer. See Windshield Washer on page 3-10 (cid:127) Cruise Control. See Cruise Control on page 3-11. For more information on the exterior lamps, see Exterior Lamps on page 3-14 later in this section. The lever on the left side of the steering column includes the following: Turn Signal and Lane-Change Indicator. See Turn and Lane-Change Signals on page 3-8. (cid:127) Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. 3-7 (cid:127) (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. Turn Signal On Chime If you leave either one of your turn signals on and drive more than 3/4 mile (1.2 km), a chime will sound to alert you. Headlamp High/Low-Beam Changer To change your headlamps from low beams to high beams, or high to low, pull the multifunction lever all the way toward you. Then release it. While the high beams are on, this light on the instrument panel cluster also will be on. To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If the arrow ﬂashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 5-95. 3-8 This light works only while the ignition key is in the ON position, and your fog lamps (if equipped) will not be illuminated when your high beams are on. Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beams (to signal that you are going to pass). If you have the headlamps on, they will return to low-beams when you release the lever. This feature operates even when the headlamps are off. Windshield Wipers The windshield wipers will operate with the ignition in ACC or ON. WIPER: To operate the windshield wipers, turn the band labeled WIPER, located on the multifunction lever, upward or downward. OFF: To stop the wipers turn the band to OFF. The ﬁve marks between OFF and LO are delay settings. For a longer delay between wiping cycles, turn the band downward. For a shorter delay between wiping cycles turn the band upward. LO (Low Speed): Turn the band up to LO for a steady wiping at a low speed. HI (High Speed): Turn the band up to HI for a steady wiping at a high speed. MIST: Turn the band downward to MIST for a single wiping cycle. Hold the band at this setting until the windshield wipers start, then release it. The windshield wipers will stop after one wipe. If additional cycles are needed, hold the band on MIST longer. Be sure to clear ice and snow from the wiper blades before using them. Hold the band at this setting until the windshield wipers start, then release it. The windshield wipers will stop after one wipe. If additional cycles are needed, hold the band on MIST longer. Heavy snow or ice can overload your wipers. A circuit breaker will stop them until the motor cools. Clear away snow or ice to prevent an overload. If your blades become damaged, get new blades or blade inserts. See Windshield Wiper Blade Replacement on page 5-57 for more information. 3-9 Windshield Washer At the top of the multifunction lever, there’s a paddle with the word PUSH on it. To spray washer ﬂuid on the windshield, push the paddle. The wipers will run for several sweeps and then either stop or return to your preset speed. The ignition key must be in ACC or ON for this to work. See Windshield Washer Fluid on page 5-42. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. United States Canada When you are low on washer ﬂuid, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. When the ignition is turned off, this message will appear again for three seconds to remind you that the ﬂuid level is low. Until the ﬂuid tank is reﬁlled, every time you start your vehicle, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. Be sure to reﬁll the tank right away. 3-10 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, the cruise control shuts off. If your vehicle is in cruise control when the traction control system (option) begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on page 4-8. When road conditions allow you to safely use it again, you may turn the cruise control back on. Setting Cruise Control The cruise control OFF ON switch is located at the end of the multifunction lever. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Slide the cruise control OFF ON lever, on the multifunction lever, to ON. 2. Get up to the speed you want. 3-11 3. Press the SET button located on the steering wheel and release it. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course shuts off the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, press the RESUME button on your steering wheel. You’ll go back to your chosen speed and stay there. 4. Take your foot off the accelerator. The CRUISE light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. 3-12 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press the SET button on the steering wheel, then release the button and the accelerator pedal. You’ll now cruise at the higher speed. (cid:127) Press the ACCEL (Accelerate) button on the steering wheel. Hold it there until you get up to the speed you want and then release the button. (To increase your speed in very small amounts, press the ACCEL button brieﬂy and then release it. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster.) The accelerate feature will only work after you set the cruise control speed by pressing the SET button on the steering wheel. Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: (cid:127) Press the COAST button on the steering wheel until you reach the lower speed you want, then release it. To slow down in very small amounts, press the COAST button on the steering wheel brieﬂy. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise speed you set earlier. 3-13 (cid:127) Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and don’t use cruise control on steep hills. Ending Cruise Control There are three ways to cancel the cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Slide the OFF ON lever, on the multifunction lever, to OFF. (cid:127) Press the COAST and ACCEL buttons at the same time. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. 3-14 Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: (cid:127) Headlamps Taillamps (cid:127) Parking Lamps License Plate Lamps Instrument Panel Lights (cid:127) (cid:127) (cid:127) The exterior lamps control has three positions: Off: Push the control all the way in to turn off the exterior lamps. Parking Lamps: Pull the control out halfway to turn on the parking lamps together with the following: Taillamps License Plate Lamps Instrument Panel Lights Headlamps: Pull the control all the way out to turn on the headlamps together with the previously listed lamps and lights. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on. Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature described previously in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until either a 30 second or 60 second lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see Vehicle Customization Settings on page 3-91. 3-15 (cid:127) (cid:127) (cid:127) Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it isn’t covered. The DRL system’s automatic headlamp control will make your low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is ON, the exterior lamps control is OFF, and the gearshift is not in PARK (P). When the DRL are on, only your low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker and other lamps won’t be on. Your instrument panel and cluster won’t be lit up either. 3-16 When it’s dark enough outside, your low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with your headlamps will also come on. When it’s bright enough outside, your headlamps will go off and your DRL will come on. As with any vehicle, you should turn on the regular headlamp system when you need it. Fog Lamps If your vehicle is equipped with fog lamps, the button is located on the instrument panel next to the exterior lamps control wheel to the left of the steering column. Your ignition must be in ON for the fog lamps to illuminate. (cid:127) (cid:127) (cid:127) To turn the fog lamps on, press the FOG button. A light will come on in the button to let you know that the fog lamps are on. Press the FOG button again to turn the fog lamps off. The ignition must be ON and the parking lamps must be on for your fog lamps to work. The fog lamps will go off while you change to high-beam headlamps. Instrument Panel Brightness The control for the instrument panel lights is located on the exterior lamps control. Your parking lamps must be on for this feature to work. Turn the control clockwise to brighten the lights or counterclockwise to dim them. Courtesy Lamps When any door is opened, several lamps come on. These lamps are courtesy lamps. They make it easy for you to enter and leave your vehicle. You can also turn these lamps on by turning the exterior lamps control all the way clockwise. Dome Lamp If your vehicle has this feature, the dome lamp will come on when you open a door. You can also turn this lamp on by turning the exterior lamps control clockwise as far as it will go. Vehicles that have the optional sunroof do not have a dome lamp. Entry Lighting Your vehicle may be equipped with courtesy lamps that will come on and stay on for a set time whenever you press UNLOCK on the remote keyless entry transmitter (if equipped). If you open a door, the lamps will stay on while it’s open and then turn off automatically about 25 seconds after you close it. If you press UNLOCK and don’t open a door, the lamps will turn off after about 40 seconds. Entry lighting includes a feature called theater dimming. With theater dimming, the lamps don’t just turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON or press the power door lock switch. The lamps will dim right away. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps won’t come on unless a door is opened. 3-17 If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. Parade Dimming The instrument panel has an added feature called parade mode. This feature prohibits the dimming of your instrument panel displays during the daylight while the headlamps are on so that you’ll still be able to see the displays. Reading Lamps Your vehicle may be equipped with reading lamps that are located on the assist handles in the headliner. These lamps and the interior courtesy lamps come on when any door is opened. Press the lens to turn them on and off. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: The ignition is ON, the doors are locked, or an illumination period of 25 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: The ignition is ON, the power door locks are activated, or an illumination period of 25 seconds has elapsed. 3-18 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave on the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp. If you leave any of these lamps on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps won’t come back on again until you do the following: Turn the ignition on, or turn the exterior lamps control off, then on again. If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. Battery rundown protection will also work if the headlamps are left on. After having been left on for 10 minutes, the headlamps and the parking lamps will ﬂash three times. They will remain on for one more minute before turning off automatically. Accessory Power Outlets Your vehicle has a 12-volt outlet which can be used to plug in electrical equipment such as a cellular telephone, a compact disc player, etc. Console Version shown On vehicles with a center console, it is located at the rear of the console. Lift the cover to access the outlet. Close the cover when not using the outlet. On vehicles without a center console, it is located in the ashtray drawer to the right of the ashtray. Remove the rubber cover to access the outlet. When not using the outlet, make sure the cover is on it. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. 3-19 (cid:127) (cid:127) Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle and adapter fuses. If you experience a problem, see your dealer for additional information on the power accessory plugs. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Check with your dealer before adding electrical equipment, and never use anything that exceeds the amperage rating. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause If you put papers or other ﬂammable items Ashtrays and Cigarette Lighter Your vehicle may have an ashtray and a cigarette lighter. The ashtray and cigarette lighter may be located on the console, if your vehicle has one, otherwise, they may be located on the instrument panel. To remove the ashtray open the door and pull up on either corner. Notice: in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Do not use anything other than the cigarette lighter in the heating element. To use the lighter, just push it in all the way and let go. When it’s ready, it will pop back out by itself. 3-20 Climate Controls Dual Climate Control System With this system you can control the heating, cooling, defrost, defog and ventilation for your vehicle. Manual Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode allows for approximately a 50/50 split of air to the instrument panel outlets and to the ﬂoor outlets. 6 (Floor): This mode directs most of the air to the ﬂoor outlets, with some of the air directed to the windshield and side window outlets. In this mode, the system will automatically select Outside Air. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. By positioning the right knob between two modes, a combination of those two modes is selected. It should be noted, that the air conditioning compressor will be engaged unless the outside temperature is 40°F (4°C) or below. Recirculation cannot be selected when in Floor Mode. 3-21 9 (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter, if equipped, may need to be replaced. For more information, see Passenger Compartment Air Filter on page 3-25 and Scheduled Maintenance on page 6-4. : (Outside Air): Press this button to turn the outside air mode on. When this mode is on, outside air will circulate throughout your vehicle. When the button is pressed, an indicator light in the button will come on to let you know that it is activated. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode. You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp. ? (Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on. When the button is pressed, an indicator light will come on. You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp. The recirculation mode cannot be used with outside air modes. D or P (Temperature Control): Slide the levers marked D (Driver) or P (Passenger) to increase or decrease the temperature on the driver’s side or the passenger’s side of the vehicle. # (Air Conditioning): Press this button to turn the air conditioning system on or off. When A/C is pressed, an indicator light will come on to let you know that the air conditioning has been activated. You may have to set the instrument panel brightness control to the highest setting during the day to see the indicator lamp. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. 3-22 For quick cool down on hot days, do the following: 1. Select the vent mode. 2. Select the recirculation mode. 3. Select A/C. 4. Select the coolest temperature for both zones. 5. Select the highest fan speeds. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air inside of your vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob clockwise to select the defog or defrost mode. - (Defog): This mode directs air equally to the windshield and the ﬂoor outlets. When you select this mode, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is below 40°F (4°C). The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0 (Defrost): This mode directs half of the air to the windshield and side window vents and half to the ﬂoor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defog mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is below 40°F (4°C). Do not drive the vehicle until all the windows are clear. 3-23 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <: The rear window defogger will turn off approximately 20 minutes after the button is pressed. If turned on again, the defogger will run for the same amount of time. The defogger can also be turned off by pressing the button again or by turning off the engine. Do not drive the vehicle until all the windows are clear. If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. Notice: Don’t use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs wouldn’t be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Outlet Adjustment Use the knob located below or to the side of the outlet, to change the direction of the air ﬂow. Operation Tips (cid:127) Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside your vehicle more effectively. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter, if equipped, may need to replaced. For more information, see Passenger Compartment Air Filter on page 3-25 and Scheduled Maintenance on page 6-4. 3-24 (cid:127) Passenger Compartment Air Filter Your vehicle may be equipped with a passenger compartment particulate air ﬁlter. It is located underneath the hood just below the windshield wiper arm on the passenger’s side of the vehicle, underneath the air inlet grille. The ﬁlter traps most of the pollen from air entering the Climate Control System. Like your engine’s air cleaner/ﬁlter, it may need to be changed periodically to ensure system performance. For information on how often to change the passenger compartment air ﬁlter, see Scheduled Maintenance on page 6-4. To change the passenger compartment air ﬁlter, use the following steps: 1. Turn off the ignition when the windshield wipers are in the up position. 2. Raise the vehicle hood. 3. Disconnect the windshield washer pump hose from the fender rail and air inlet grille. 4. Peel back the hood weatherstrip from the passenger’s side of the vehicle halfway to center. 5. Remove the air inlet grille retainers. 6. Remove the air inlet grille. 7. Remove the old passenger compartment air ﬁlter. 8. Reverse the steps to install the new air ﬁlter. For the type of ﬁlter to use, see Normal Maintenance Replacement Parts on page 6-13. 3-25 Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly – and even dangerous. So please get to know your warning lights and gages. They’re a big help. Your vehicle may also have a Driver Information Center (DIC) that works along with the warning lights and gages. See Driver Information Center (DIC) on page 3-49. 3-26 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel is in your tank and many other things you need to drive safely and economically. Uplevel 3400 V6 Engine Cluster: United States version with ABS and Traction Control shown, Canada similar 3-27 Uplevel 3800 V6 Engine Cluster: United States version with ABS and Traction Control shown, Canada similar 3-28 Uplevel 3800 Supercharged V6 Engine Cluster: United States version with ABS and Traction Control shown, Canada similar

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2005 Chevrolet Impala Owners Manual