2014 Chevrolet Cruze Owners Manual

display format.

4. To save the settings, press the

MENU/SEL knob.

To set the 12/24 hour format for the radio without navigation: 1. Press CLOCK. 2. Highlight 12/24 Hour Format. 3. Press the MENU/SEL knob to select the 12 hour or 24 hour display format.

4. To save the settings, press OK

screen button.

To set the 12/24 hour format for the radio with navigation: 1. Press CLOCK. 2. Highlight 12/24 Hour Format. 3. Press the MENU/SEL knob to select the 12 hour or 24 hour display format.

4. To save the settings, press the

BACK on the radio faceplate.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (6,1)

5-6

Instruments and Controls

Certain electrical accessories may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. See Add-On Electrical Equipment on page 9-69. { Caution

Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Cigarette Lighter If equipped with a cigarette lighter, it is on the center floor console near the shift lever. To activate the cigarette lighter, push it into the heating element and let go. When the lighter is ready it will pop back out.

{ Caution

Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.

Power Outlets The accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player. There is one accessory power outlet located on the center floor console and one on the rear of the center floor console. These outlets are powered when the key is in ON/ RUN or ACC/ACCESSORY, or until the driver door is opened within 10 minutes of turning off the vehicle. See Retained Accessory Power (RAP) on page 9-23. Open the cover to access. { Caution

Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 amp rating.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (7,1)

Instruments and Controls

5-7

When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Follow this manual's advice. Waiting to do repairs can be costly and even dangerous.

Ashtrays If equipped with a removable ashtray, the ashtray can be placed into the front console cupholders. To open the ashtray, lift the lid of the ashtray. After using, close the lid. To empty the ashtray for cleaning, slightly turn the upper part of the ashtray counterclockwise and remove it.

{ Caution

Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working. Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (8,1)

5-8

Instruments and Controls

Instrument Cluster

English Gas Cluster with Automatic Transmission Shown, Metric and Manual Transmission Similar

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (9,1)

Instruments and Controls

5-9

English Diesel Cluster Shown, Metric Similar

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (10,1)

5-10

Instruments and Controls

The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) on page 5-23.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm).

{ Caution

If the engine is operated with the tachometer in the shaded warning area, the vehicle could be damaged, and the damages would not be covered by the vehicle warranty. Do not operate the engine with the tachometer in the shaded warning area.

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper‐resistant odometer. The digital odometer will read 999,999 if it is turned back. If the vehicle needs a new odometer installed, it must be set to the mileage total of the old odometer. If that is not possible, then it must be set at zero and a label must be put on the driver door to show the old mileage reading when the new odometer was installed.

Trip Odometer The trip odometer can show how far the vehicle has been driven since the trip odometer was last reset.

Fuel Gauge

Gas Shown

When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. A FUEL LEVEL LOW message may appear in the Driver Information Center (DIC) and a single chime sounds. See Fuel System Messages on page 5-29 for more information.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (11,1)

Here are four things that some owners ask about. None of these show a problem with the fuel gauge: . At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. The gauge moves a little while turning a corner or speeding up. The gauge takes a few seconds to stabilize after the ignition is turned on, and will go back to empty when the ignition is turned off.

Engine Coolant Temperature Gauge

Instruments and Controls

5-11

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.

This gauge shows the engine coolant temperature. If the indicator needle moves to the hot side of the gauge toward the H or shaded area, the engine is too hot. If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (12,1)

5-12

Instruments and Controls

Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System on page 3-23.

When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.

The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the warning light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3-16.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.

{ Warning

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages on page 5-32.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (13,1)

Instruments and Controls

5-13

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3-23 for important safety information. The instrument panel has a passenger airbag status indicator.

United States

Canada

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds

as a system check. Then, after several seconds, the status indicator will light either ON or OFF, or the on or off symbol to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and passenger knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ Warning

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5-12 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (14,1)

5-14

Instruments and Controls

The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in ON/RUN for key access or Service Only Mode for Keyless Access, as a check to show it is working. If it

does not, have the vehicle serviced by your dealer. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16.

can prevent more serious damage to the vehicle. This system also assists the dealer technician in correctly diagnosing any malfunction.

{ Caution

If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

{ Caution

Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the

(Continued)

If the malfunction indicator lamp comes on while the engine is running, this indicates that the OBD II system has detected a problem and diagnosis and service might be required. With a diesel engine, this light may also come on when the OBD II system has detected a problem with the Diesel Exhaust Fluid (DEF) management system. See Diesel Exhaust Fluid on page 9-27. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (15,1)

Caution (Continued)

same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10-3.

This light can come on during a malfunction in one of two ways: Light Flashing (Gasoline Engine Only): A misfire condition has been detected and is present. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.

Instruments and Controls

5-15

To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady (All Engines): An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission control system malfunction:

For gasoline engines, check that the gas cap is fully installed. See Filling the Tank on page 9-61. The diagnostic system can determine if the gas cap has

been left off or improperly installed. A loose or missing gas cap allows gasoline to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. For all engines, check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up.

If one or more of these conditions occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel (Gasoline) on page 9-52.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (16,1)

5-16

Instruments and Controls

If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).

The DLC is under the instrument panel next to the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:

The malfunction indicator lamp is on when the engine is running, or while the vehicle is in ON/ RUN or in Service Only Mode and the malfunction indicator lamp does not come on. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed by the system. If this were to occur, the vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down.

The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (17,1)

Instruments and Controls

5-17

Start the engine again to reset the system. If the light stays on after driving at a speed above 20 km/h (13 mph), see your dealer for service. A chime may also sound when the light comes on steady. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5-16. See Brake System Messages on page 5-27 for all brake‐related DIC messages.

Up-Shift Light

If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10-85.

Antilock Brake System (ABS) Warning Light

The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off.

Metric

English

The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer.

{ Warning

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (18,1)

5-18

Instruments and Controls

For manual transmission vehicles, there is an up-shift light that comes on in the lower DIC area. It shows when to shift to the next higher gear for best fuel economy. See Manual Transmission on page 9-37.

Power Steering Warning Light

This light comes on briefly when the ignition is turned to ON/RUN as a check to show it is working. If it does not come on have the vehicle serviced by your dealer. If this light stays on, or comes on while driving, the system may not be working. If this happens, see your dealer for service.

Traction Off Light

StabiliTrak® OFF Light

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control on page 9-41.

This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control on page 9-41.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (19,1)

Instruments and Controls

5-19

Traction Control System (TCS)/StabiliTrak® Light

If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control on page 9-41.

Wait-to-Start Light

Tire Pressure Light

This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS, and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service.

For diesel engines, the wait-to-start light shows that the engine is functioning properly and indicates when the engine can be started. The fast warm-up glow plug system makes the wait-to-start light stay on for a shorter amount of time than most diesel engines. For more information, see Starting the Engine on page 9-18.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5-33. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10-51.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (20,1)

5-20

Instruments and Controls

When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10-53.

Engine Oil Pressure Light

low can also damage the

{ Caution Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Low Fuel Warning Light

Gas Shown

This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (21,1)

For vehicles with a Driver Information Center (DIC), see Driver Information Center (DIC) on page 5-23 for more information.

Diesel Exhaust Fluid (DEF) Warning Light

This light, a Driver Information Center (DIC) Message, and a chime come on when there is an issue with the Diesel Exhaust Fluid. See Diesel Exhaust Fluid Messages on page 5-29 for information on the specific message displaying with the light. If the DEF fluid issue has not been corrected, the light will continue to flash. The vehicle's speed may also be limited.

Instruments and Controls

5-21

Also see Diesel Exhaust Fluid on page 9-27.

Reduced Engine Power Light

Security Light

The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2-17.

The reduced engine power light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. This light, along with the malfunction indicator lamp, displays when a noticeable reduction in the vehicle's performance occurs. The vehicle can be driven at a reduced speed when the reduced engine power light is on but acceleration and speed might be reduced. If this light stays on, see your dealer as soon as possible for diagnosis and repair.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (22,1)

5-22

Instruments and Controls

High-Beam On Light

The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6-2 for more information.

Front Fog Lamp Light

For vehicles with front fog lamps, this light comes on when the front fog lamps are in use.

The light goes out when the front fog lamps are turned off. See Front Fog Lamps on page 6-4 for more information.

Lamps On Reminder

For vehicles with cruise control, the cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light turns off when the cruise control is turned off. See Cruise Control on page 9-43.

Door Ajar Light

This light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6-1.

Cruise Control Light

If equipped, this light comes on when a door is open or not securely latched. Before driving, check that all doors are properly closed. See Door Ajar Messages on page 5-28.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (23,1)

Instruments and Controls

5-23

Information Displays

DIC Buttons

Driver Information Center (DIC) The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5-27. All messages appear in the DIC display in the center of the instrument cluster. DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever. The DIC displays trip, fuel, and warning messages if a system problem is detected.

1. SET/CLR: Press to set, or press and hold to clear, the menu item displayed.

2. w x : Use the band to scroll

through the items in each menu. 3. MENU: Press to display the Trip/

Fuel Menu and the Vehicle Information Menu. On some vehicles, there is also an ECO Menu. This button is also used to return to or exit the last screen displayed on the DIC.

Trip/Fuel Menu (TRIP) Items Press MENU on the turn signal lever until the TRIP menu displays. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Trip 1 or Trip 2, Average Fuel Economy, Average Vehicle Speed: Displays the current distance traveled, in either kilometers (km) or miles (mi), from the last reset for the trip odometer. The trip odometer can be reset to zero by pressing and holding the SET/CLR button while the trip odometer display is showing. Also displays the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This display is shown as

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (24,1)

5-24

Instruments and Controls

. c L/100 km (mpg). Reset the average consumption by pressing SET/CLR when it is displayed. This screen also displays the average vehicle speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is based on the various vehicle speeds recorded since the last reset. This display is shown as c km/h (mph). Reset the average speed by pressing SET/CLR when it is displayed. Blank Display: Displays no information. Digital Speed: Displays how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset. Fuel Used: Displays the approximate liters (L) or gallons (gal) of fuel that have been used since last reset. The fuel used can be reset by pressing the SET/CLR button while the Fuel Used display is showing.

Timer: To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR. Navigation: Used for the OnStar or navigation system Turn-by-Turn guidance. See OnStar Overview on page 14-1 or the navigation manual, if the vehicle has navigation, for more information. Speed, Fuel Range, Instantaneous Fuel Economy: Displays how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

The center of the page shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This display is shown as l . km (mi). Fuel range cannot be reset. Also displays the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. This display is shown as . L/100 km (mpg). This display cannot be reset.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (25,1)

Instruments and Controls

5-25

Vehicle Information Menu (OPTION) Items Press MENU on the turn signal lever until the OPTION menu is displayed. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Units: Move w x to change between Metric or US when the Unit display is active. Press SET/CLR to confirm the setting. On some models, you will have to select 1, 2, or 3 for the Unit display. 1 is Imperial units, 2 is US units, and 3
is metric units. This will change the displays on the cluster and DIC to the type of measurements you select. Tire Pressure: May display a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). On some models,

this display only allows for matching of the TPMS sensors. In this case, the display will show TIRE LEARN. See Tire Pressure Monitor System on page 10-52 and Tire Pressure Monitor Operation on page 10-53. Remaining Oil Life: Displays an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. This display may be shown as : %. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5-29. The oil should be changed as soon as possible. See Engine Oil on page 10-11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11-2.

The Oil Life display must be reset after each oil change. Do not reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 10-15. Battery Voltage: Displays the current battery voltage, if equipped. Battery voltage changes are normal while driving. See Charging System Light on page 5-13. If there is a problem with the battery charging system, the DIC will display a message. See Battery Voltage and Charging Messages on page 5-27. Diesel Exhaust Fluid Level (Diesel Engine Only): Displays the current Diesel Exhaust Fluid (DEF) level. Remaining Fuel Filter (Diesel Engine Only): Displays an estimate of the remaining fuel filter life. If REMAINING FUEL FILTER 50% is displayed, that means 50% of the current fuel filter life remains.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (26,1)

Economy Trend: Displays history of the Average Fuel Economy from the last 50 km (30 miles). Each bar represents about 5 km (3 miles) of driving. The fuel economy will range from 0 – 15 L/100 km (0 – 50 mpg). During driving the bars will shift to always reflect the most recent distance on the right side. This display cannot be reset.

5-26

Instruments and Controls

ECO Drive Assist Menu (ECO) Items This menu is only available on some vehicles. Press MENU on the turn signal lever until the ECO menu is displayed. Use w x to scroll through the menu items. Not all items are available on every vehicle. The following is a list of all possible menu items: Best Average Fuel Economy: The right hand side displays the best average fuel economy (AFE) that is achieved for a selected distance. The left hand side displays a running average of fuel economy for the most recently traveled selected distance. The center bar graph displays the instantaneous fuel economy. Quickly press the SET/ CLR button to display a page for selecting one of the distance options. Move the up/down arrow to choose the selection, and SET/CLR to change the setting.

When viewing best AFE, a several second press and hold of SET/CLR will reset the best value. The best value will show “- - -“ until the selected distance has been traveled. The display provides feedback on how current driving behavior in the bar graph affects the running average in the left display and how well recent driving compares to the best that has been achieved. ECO Index: The bar graph on the left hand side provides feedback on the efficiency of current driving behavior. The graph shows a percentage value that is based on current fuel consumption compared to what is expected from the vehicle with good and bad driving habits. Each box represents 10%, with all boxes filled being 100%. More economical driving will result in being in the ECO box. Instantaneous Fuel Economy is also shown on right hand side. This display cannot be reset.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (27,1)

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.

Instruments and Controls

5-27

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10-28. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10-27. RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.

Compass Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5-4. – – Two dashes will be displayed if the compass needs service. See your dealer for service.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (28,1)

5-28

Instruments and Controls

Cruise Control Messages

APPLY BRAKE BEFORE CRUISE If this message displays when attempting to activate cruise control, apply the brake pedal and try again. CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9-43.

Door Ajar Messages

DOOR(S) OPEN A vehicle symbol will be displayed on the DIC showing which door is open along with this message. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely.

TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.

ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature. HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10-23.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (29,1)

Instruments and Controls

5-29

Engine Oil Messages

Engine Power Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10-15 and Driver Information Center (DIC) on page 5-23 for information on how to reset the system. See Engine Oil on page 10-11 and Maintenance Schedule on page 11-2 for more information. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.

TIGHTEN GAS CAP (Gas Engine Only) This message displays when the fuel cap is not on tight on vehicles with gasoline engines. Tighten the fuel cap. WATER IN FUEL CONTACT SERVICE This message displays when water level in the diesel fuel filter exceeds a specified level. Residual water in the diesel fuel filter must be drained. Water in Fuel (Diesel) on page 9-61.

Diesel Exhaust Fluid Messages For more information on these messages, see “Exhaust Fluid Low” or “Exhaust Fluid Quality Poor” in Diesel Exhaust Fluid on page 9-27. EXHAUST FLUID RANGE: XXXX KM (MI) When the exhaust fluid is getting low, the range will be displayed in either kilometers or miles. It is

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (30,1)

5-30

Instruments and Controls

normal for the EXHAUST FLUID RANGE to vary based on vehicle and environmental driving conditions. When this message first displays at approximately 1 600 km (1,000 mi) of fluid range remaining, the fluid is approximately 11 L (3 gal) low. EXHAUST FLUID LOW SPEED LIMITED SOON When the exhaust fluid range is less than 120 km (75 mi) this message will be displayed. EXHAUST FLUID EMPTY REFILL NOW This message will be displayed when the exhaust fluid is empty. This message may be accompanied by other messages that provide more information.

EXHAUST FLUID QUALITY POOR SEE OWNERS MANUAL NOW This message displays when the exhaust fluid is of poor quality or the wrong fluid was added. This message may be accompanied by other messages that provide more information.

Diesel Particulate Filter Messages

DIESEL PARTIC (Particulate) FILTER IS FULL CONTINUE DRIVING This message may display when the soot particles in the diesel particulate filter reach a certain amount. Continue driving to prevent the filter from clogging. See Diesel Particulate Filter on page 9-26 for more information.

DIESEL PARTIC (Particulate) FILTER IS FULL CONTINUED DRIVING MANDATORY This message may display when the soot particles in the diesel particulate filter reach a certain amount. Continued driving is mandatory to prevent the filter from clogging. See Diesel Particulate Filter on page 9-26 for more information.

Key and Lock Messages

NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with Keyless Access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2-3.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (31,1)

PLACE TRANSMITTER IN POCKET This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2-3. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-3.

Instruments and Controls

5-31

Lamp Messages

AUTOMATIC LIGHT CONTROL ON This message is displayed when the automatic light control has been turned on. See Automatic Headlamp System on page 6-3. AUTOMATIC LIGHT CONTROL OFF This message is displayed when the automatic light control has been turned off. See Automatic Headlamp System on page 6-3. XXX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10-32 and Replacement Bulbs on page 10-37 for more information on turn signal bulb replacement.

TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Object Detection System Messages

PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9-45. SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9-45.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (32,1)

5-32

Instruments and Controls

SERVICE SIDE DETECTION SYSTEM If this message appears, the system needs service. Take the vehicle to your dealer. SIDE BLIND ZONE ALERT OFF This message indicates that the driver has turned the system off. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that the Side Blind Zone Alert (SBZA) system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also activate during heavy rain or due to road spray. The vehicle does not need service. For cleaning, see Exterior Care on page 10-88.

Ride Control System Messages

SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control/Electronic Stability Control on page 9-41. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. See Traction Control/Electronic Stability Control on page 9-41.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Security Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

CHANGE TIMING BELT This message displays when scheduled maintenance on the timing belt is required. See your dealer for service. SERVICE POWER STEERING This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE STEERING COLUMN LOCK This message displays if there is a problem with the steering column lock. Take the vehicle to your dealer for service.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (33,1)

SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Starting the Vehicle Messages

TURN STEERING WHEEL START VEHICLE AGAIN This message displays when you try to start the vehicle, but the column remains locked. Try turning the steering wheel while starting the vehicle to unlock the steering column. If the vehicle still does not start, turn the steering wheel the other way, and try starting the vehicle again.

Instruments and Controls

5-33

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10-53 for more information. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10-53 for more information. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. There is also an icon with the warning that will indicate the location of the low tire.

The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-19. If a tire pressure message displays, inflate the tires until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10-43, Vehicle Load Limits on page 9-9, and Tire Pressure on page 10-51. More than one tire pressure message can be received at a time. To read the other messages that may have been sent at the same time, press the SET/CLR button. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5-23.

Transmission Messages

SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (34,1)

5-34

Instruments and Controls

TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible. STEERING COLUMN IS LOCKED This message displays when the steering column is locked.

Vehicle Speed Messages For more information on these messages, see Diesel Exhaust Fluid on page 9-27. XXX KM (MI) UNTIL 105 KM/H (65 MPH) MAX SPEED This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, SERVICE EMISSION SYSTEM, or SERVICE EXHAUST FLUID SYSTEM. The vehicle speed will be limited to 105 km/h (65 mph) when the countdown is over. XXX KM (MI) UNTIL 88 KM/H (55 MPH) MAX SPEED This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, SERVICE EMISSION SYSTEM, or SERVICE EXHAUST FLUID SYSTEM. The

vehicle speed will be limited to 88 km/h (55 mph) when the countdown is over. XXX KM (MI) UNTIL 7 KM/H (4 MPH) MAX SPEED This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, or SERVICE EXHAUST FLUID SYSTEM. The vehicle speed will be limited to 7 km/h (4 mph) when the countdown is over. SPEED LIMITED TO 105 KM/H (65 MPH) This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, SERVICE EMISSION SYSTEM, or SERVICE EXHAUST FLUID SYSTEM. When this message is displayed, the vehicle speed is being limited to 105 km/h (65 mph).

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (35,1)

Instruments and Controls

5-35

TRANSITIONING TO XX KM/H (XX MPH) MAX SPEED This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, SERVICE EMISSION SYSTEM, or SERVICE EXHAUST FLUID SYSTEM. When this message is displayed, the end of the countdown has been reached and the vehicle speed is being limited.

SPEED LIMITED TO 88 KM/H (55 MPH) This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, SERVICE EMISSION SYSTEM, or SERVICE EXHAUST FLUID SYSTEM. When this message is displayed, the vehicle speed is being limited to 88 km/h (55 mph). SPEED LIMITED TO 7 KM/H (4 MPH) This message will be displayed along with other messages. These messages include EXHAUST FLUID EMPTY REFILL NOW, EXHAUST FLUID QUALITY POOR, or SERVICE EXHAUST FLUID SYSTEM. When this message is displayed, the vehicle speed is being limited to 7 km/h (4 mph).

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. MENU/SEL: Press the center of this knob to enter the menus and select menu items. Turn the knob to scroll through the menus. BACK: Press to exit or move backward in a menu.

Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu. 2. Turn the MENU/SEL knob to

highlight Vehicle Settings. Press the CONFIG button until Vehicle is highlighted on vehicles with a navigation system only.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (36,1)

5-36

Instruments and Controls

3. Press the center of the MENU/ SEL knob to select the Vehicle Settings menu. The ignition must be in ON/RUN.

The following list of menu items may be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Languages Lighting

. Power Door Locks . Remote Locking, Unlocking,

Starting

. Return to Factory Settings Turn the MENU/SEL knob to highlight the menu. Press the knob to select it. Each of the menus is detailed in the following information. Vehicles with a navigation system will display a check mark to indicate this feature is on.

Climate and Air Quality If equipped, select the Climate and Air Quality menu and the following will be displayed: . Auto Fan Speed . Air Quality Sensor . Remote Start Auto Heat Seats . Auto Defog . Auto Rear Defog

Auto Fan Speed This feature sets the climate control fan speed to maintain the interior temperature. Press the MENU/SEL knob when Auto Fan Speed is highlighted to open the menu. Turn the knob to highlight High, Medium, or Low. Press the BACK button to confirm the selection and move back to the last menu.

Air Quality Sensor Allows the selecting low or high sensitivity of the air quality sensor. Only vehicles with the automatic climate control will have this option. Press the MENU/SEL knob when Air Quality Sensor is highlighted to open the menu. Turn the knob to highlight High Sensitivity or Low Sensitivity. Press the BACK button to confirm the selection and move back to the last menu.

Remote Start Auto Heat Seats On vehicles with remote start and heated seats, the heated seats can be set to on or off. Press the MENU/SEL knob when Remote Start Auto Heat Seats is highlighted to open the menu. Turn the knob to highlight On or Off. Press the BACK button to confirm the selection and move back to the last menu.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (37,1)

Instruments and Controls

5-37

Auto Defog When turned on and high humidity is detected, the climate control system may adjust to outside air supply and turn on the air conditioner or the heater. The fan speed may slightly increase to help prevent fogging. When high humidity is no longer detected, the system will return to its prior operation. Press the MENU/SEL knob when Auto Defog is highlighted to open the menu. Turn the knob to highlight On or Off. Press the BACK button to confirm the selection and move back to the last menu.

Auto Rear Defog When on, this feature turns on the rear defogger at vehicle start when the interior temperature is cold and fog is likely. The auto rear defog function can be disabled by pressing 1. When off, the feature can be turned on by pressing 1.

See “Rear Window Defogger” under Climate Control Systems on page 8-1. Press the MENU/SEL knob when Auto Rear Defog is highlighted to open the menu. Turn the knob to highlight On or Off. Press the knob to confirm the selection and move back to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and Chime Volume will be displayed.

Chime Volume This allows the selection of the chime volume level. Press the MENU/SEL knob when Chime Volume is highlighted. Turn the knob to select Normal or High. Press the BACK button to confirm and go back to the last menu.

Collision/Detection Systems If equipped, select the Collision/ Detection Systems menu and the following may be displayed. . Park Assist . Side Blind Zone Alert

Park Assist This allows the Ultrasonic Parking Assist feature, to be turned on or off. Press the MENU/SEL knob when Park Assist is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Side Blind Zone Alert This allows the Side Blind Zone Alert feature to be turned on or off. Press the MENU/SEL knob when Side Blind Zone Alert is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (38,1)

5-38

Instruments and Controls

Languages Select the Language menu and the following will be displayed: . English

Francais . Espanol Turn the MENU/SEL knob to select the language. Press BACK to return to the last menu. Lighting Select the Lighting menu and the following will be displayed: . Exit Lighting . Vehicle Locator Lights

Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the MENU/SEL knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds,

1 Minute, or 2 Minutes. Press the BACK button to confirm and go back to the last menu.

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. When on, the headlamps, parking lamps, taillamps, back-up lamps, and most of the interior lamps will flash when K is pressed. Press the MENU/SEL knob when Vehicle Locator Lights is highlighted to open the menu. Turn the MENU/ SEL knob to highlight On or Off. Press MENU/SEL to select On or Off. Press the BACK button to confirm the selection and move back to the last menu. Power Door Locks Select Power Door Locks and the following will be displayed: . Auto Door Unlock . Delayed Door Lock . Unlocked Door Anti Lock Out

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park) with a automatic transmission or when the key is removed from the ignition with a manual transmission. Press the MENU/SEL knob when Auto Door Unlock is highlighted. Turn the knob to select All Doors, Driver Door, or Off. Press the knob to confirm and go back to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. Three chimes signal delayed locking is in use. Press either the power lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors.

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-6007168) - 2014 - 2nd Edition - 7/15/13

Black plate (39,1)

Instruments and Controls

5-39

Press the MENU/SEL knob when Delayed Door Lock is highlighted to select On or Off. Press BACK to return to the last menu.

Unlocked Door Anti Lock Out When on, all doors will lock. The driver door will then unlock if door locking is requested while the driver door is open, and disable the Delayed Door Lock feature. Even when this feature is off, the driver is protected from accidental lockouts when the key is in the ignition. If Off is selected, the Unlocked Door Anti Lock Out feature may be enabled through an additional menu selection. Press the MENU/SEL knob when Unlocked Door Anti Lock Out is highlighted to select On or Off. Press BACK to return to the last menu.

Remote Locking, Unlocking, Starting Select Remote Locking, Unlocking, Starting and the following will be