2011 Chevrolet Camaro Owners Manual

5-16

Instruments and Controls

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑31
for important safety information. The overhead console has a passenger airbag status indicator.

United States

If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

Canada and Mexico

When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. If you are using remote start, if equipped, to start your vehicle from a distance, you may not see the system check. Then, after several seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger frontal airbag.

Chevrolet Camaro Owner Manual - 2011

Black plate (17,1)

Instruments and Controls

5-17

{ WARNING

Charging System Light

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑15 for more information, including important safety information.

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started.

If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages on page 5‑34. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Chevrolet Camaro Owner Manual - 2011

Black plate (18,1)

5-18

Instruments and Controls

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.

This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer.

If the Malfunction Indicator Lamp comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.

Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10‑3.

Chevrolet Camaro Owner Manual - 2011

Black plate (19,1)

This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. The following can prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible.

Instruments and Controls

5-19

Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission system malfunction: . Make sure the fuel cap is fully installed. See Filling the Tank on page 9‑51. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.

. Make sure the electrical system is not wet. The system could be wet if the vehicle was driven through a deep puddle of water. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off.

. Make sure to fuel the vehicle

with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑48.

If none of the above have made the light turn off, have your dealer check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.

Chevrolet Camaro Owner Manual - 2011

Black plate (20,1)

5-20

Instruments and Controls

Emissions Inspection and Maintenance Programs Some state/provincial and local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).

The DLC is under the instrument panel near the steering wheel. See your dealer if assistance is needed.

The vehicle may not pass inspection if:

The Malfunction Indicator Lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. The critical emission control systems have not been completely diagnosed by the system. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system evaluates critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

English

Metric

If the vehicle has antilock brakes, this light should come on when the key is turned to START. If it does not come on, have it fixed so it will be ready to warn if there is a problem.

Chevrolet Camaro Owner Manual - 2011

Black plate (21,1)

When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem. If, while driving, the light comes on and a brake message comes on the Driver Information Center (DIC), pull off the road and stop carefully. The pedal could be harder to push or the pedal can go closer to the floor. It could take longer to stop. If the light is still on, have the vehicle towed for service. See Antilock Brake System (ABS) Warning Light on page 5‑21 and Towing the Vehicle on page 10‑95.

Instruments and Controls

5-21

{ WARNING

Antilock Brake System (ABS) Warning Light

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

The brake message remains on until the menu button is pressed. The brake light remains until the problem is fixed. See Brake System Messages on page 5‑34 for more information.

This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off.

Chevrolet Camaro Owner Manual - 2011

Black plate (22,1)

5-22

Instruments and Controls

If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady. If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning. If both the ABS and the Brake System Warning Light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light on page 5‑20. See Brake System Messages on page 5‑34 for all brake related DIC messages.

Traction Off Light

Traction Control System (TCS)/StabiliTrak® Light

This light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the traction control button. This light also comes on and the system turns off if there is a problem with the TCS. If the light comes on and stays on for an extended period of time while the system is turned on, the vehicle needs service. See Traction Control System (TCS) on page 9‑38 and StabiliTrak® System on page 9‑39 for more information.

The StabiliTrak system or the Traction Control System (TCS) indicator/warning light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally the indicator light will then go off. The indicator/warning light flashes while the StabiliTrak or TCS system is working to control the vehicle on a low traction surface. If the TCS indicator/warning light comes on and stays on while driving, the vehicle needs service.

Chevrolet Camaro Owner Manual - 2011

Black plate (23,1)

Instruments and Controls

5-23

See Competitive Driving Mode on page 9‑41, Traction Control System (TCS) on page 9‑38 and StabiliTrak® System on page 9‑39
for more information

Traction Control System (TCS) OFF/StabiliTrak® OFF Light

For SS models, if this light is on, the vehicle is in Competitive Mode. A warning also appears in the DIC for StabiliTrak Competitive Mode. See Ride Control System Messages on page 5‑38 for more information. See Traction Control System (TCS) on page 9‑38 and StabiliTrak® System on page 9‑39 for more information

Tire Pressure Light

This light comes on when the StabiliTrak system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If the StabiliTrak system is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak system and the warning light turns off.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message can accompany the light. See Tire Messages on page 5‑39 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑58
for more information.

When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 10‑62 for more information.

Chevrolet Camaro Owner Manual - 2011

Black plate (24,1)

5-24

Instruments and Controls

Engine Oil Pressure Light

{ WARNING

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule for changing engine oil.

The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

Immobilizer Light

The immobilizer light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the system is working normally the indicator light turns off. This light comes on when the ignition is turned from LOCK/OFF to ON/RUN and stays on if the vehicle is immobilized. This happens when an incorrect key or an unprogrammed key is used to start the vehicle.

Chevrolet Camaro Owner Manual - 2011

Black plate (25,1)

If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2‑12 for more information.

Front Fog Lamp Light

The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Front Fog Lamps on page 6‑5 for more information.

Instruments and Controls

5-25

Taillamp Indicator Light

Information Displays

Driver Information Center (DIC) The vehicle may have a Driver Information Center (DIC). The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5‑34 for more information. All messages appear in the DIC display located in the center of the instrument panel cluster. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5‑42 for more information.

This light comes on when the taillamps are in use.

Cruise Control Light

This light is white when the cruise control is set and will be green when the system is active. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑43 for more information.

Chevrolet Camaro Owner Manual - 2011

Black plate (26,1)

5-26

Instruments and Controls

DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever located on the left side of the steering wheel. The DIC displays trip, fuel, vehicle system information, and warning messages if a system problem is detected. The bottom of the DIC display shows what position the shift lever is in (Automatic Transmission Only), the odometer, and the direction the vehicle is driving.

DIC Buttons

Trip/Fuel Menu Items Press the MENU button on the turn signal lever until Trip/Fuel Information Menu is displayed. Use the thumbwheel to scroll through the following menu items: . Digital Speedometer

MENU: Press this button to get to the Trip/Fuel Menu and the Vehicle Information Menu. w x (Thumbwheel): Use the thumbwheel to scroll through the items in each menu. SET (Set/Clear): Use this button to set or clear the menu item when it is displayed.

Trip 1
Trip 2
Fuel Range

. Average Fuel Economy . Average Vehicle Speed

Turn by Turn

. Blank

Chevrolet Camaro Owner Manual - 2011

Black plate (27,1)

Instruments and Controls

5-27

Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.

Trip 1 and Trip 2
The Trip display shows the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing the trip reset stem or the SET button while the trip odometer display is showing.

Fuel Range The Fuel Range display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.

Average Fuel Economy The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The fuel economy can be reset by pressing the SET button while the Average Fuel Economy display is showing.

Average Vehicle Speed The Average Vehicle Speed display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing the SET button while the Average Vehicle Speed display is showing.

Turn by Turn This display is used for the OnStar Turn by Turn guidance. See the OnStar Owner's Guide for more information.

Blank Display This display shows no information. Vehicle Information Menu Items Press the MENU button on the turn signal lever until Vehicle Information Menu is displayed. Use the thumbwheel to scroll through the following menu items: . Unit

Tire Pressure

. Remaining Oil Life . Coolant Temp . Battery Voltage . Speed Warning

Chevrolet Camaro Owner Manual - 2011

Black plate (28,1)

5-28

Instruments and Controls

Unit Move the thumbwheel up or down to switch between US or Metric when the Unit display is active. Press SET to confirm the setting. This will change the displays on the cluster and DIC to either English (US) or metric measurements.

Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). See Tire Pressure Monitor System on page 10‑60 and Tire Pressure Monitor Operation on page 10‑62
for more information.

Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑36. The oil should be changed as soon as possible. See Engine Oil on page 10‑10. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 11‑2 for more information.

Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system press the SET button while the Oil Life display is active. See Engine Oil Life System on page 10‑14.

Coolant Temperature This display shows the temperature of the engine cooling system fluid in either degrees Celsius (°C) or degrees Fahrenheit (°F).

Chevrolet Camaro Owner Manual - 2011

Black plate (29,1)

Instruments and Controls

5-29

Speed Warning Speed Warning allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press SET when Speed Warning is displayed. Compass The vehicle may have a compass display in the Driver Information Center (DIC). See Compass on page 5‑4 for more information.

Battery Voltage This display, available on some vehicles, shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0 Volts. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light on page 5‑17 for more information. If there is a problem with the battery charging system, the DIC will display a message. See Battery Voltage and Charging Messages on page 5‑34.

Head-Up Display (HUD)

{ WARNING

If the HUD image is too bright or too high in your field of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view.

For vehicles with the Head-Up Display (HUD), some information concerning the operation of the vehicle is projected onto the windshield. This includes the speedometer reading, RPM reading, transmission position, outside air temperature, compass heading and a brief display of the current radio station, including XM information or CD track. It will also display turn-by-turn navigation information if the vehicle has a navigation radio.

Chevrolet Camaro Owner Manual - 2011

Black plate (30,1)

5-30

Instruments and Controls

The images are projected through the HUD lens located on the driver side of the instrument panel. Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. The tap shift gear will also appear on the HUD if the vehicle has tap shift and it is active. The HUD information can be displayed in one of three languages, English, French, or Spanish. The speedometer reading and other numerical values can be displayed in either English or metric units. The language selection is changed through the radio and the units of measurement is changed through the trip computer in the Driver Information Center (DIC). See AM-FM Radio on page 7‑8
and Driver Information Center (DIC) on page 5‑25.

The following indicator lights come on the instrument panel when activated and also appear on the HUD:

Turn Signal Indicators

. High-Beam Indicator Symbol The HUD temporarily displays CHECK GAGES and ICE POSSIBLE when these messages are on the DIC trip computer. The HUD also temporarily displays the following messages on vehicles with these systems, when they are active: . Check Tire Pressure . Cruise Set To

Low Fuel

. Speed Limited To

TRACTION CONTROL ACTIVE

. STABILITRAK ACTIVE

HUD Display on the Vehicle

Windshield

The HUD information appears as an image focused out toward the front of the vehicle. When the ignition key is turned to ON/RUN, the HUD will display an introductory message for a short time, until the HUD is ready.

Chevrolet Camaro Owner Manual - 2011

Black plate (31,1)

Instruments and Controls

5-31

When the HUD is on, the speedometer reading is continually displayed. The current radio station or CD track number will display for a short period of time after the radio or CD track status changes. This happens whenever radio information is changed. The speedometer size is reduced when radio, CD information, warnings, or turn-by-turn navigation information is displayed on the HUD. When the phone feature is activated, the HUD will briefly display phone information, if available.

OFF: Turn the HUD dimming knob fully counterclockwise until the HUD display turns off. Brightness: Turn the dimming knob clockwise or counterclockwise to brighten or dim the display. « (Up): ª (Down): Press the up or down arrows to center the HUD image in your view. The HUD image can only be adjusted up and down, not side to side. PAGE: Press to select the display formats. Release the page button when the format number with the desired display is shown on the HUD. If vehicle messages are displayed, pressing PAGE may clear the message.

The HUD control is located to the right of the steering wheel. To adjust the HUD image so that items are properly displayed, do the following: 1. Adjust the driver seat to a

comfortable position.

2. Start the engine. 3. Adjust the HUD controls. Use the following settings to adjust the HUD.

Chevrolet Camaro Owner Manual - 2011

Black plate (32,1)

5-32

Instruments and Controls

The three formats are as follows:

English

English

English

Metric

Metric

Metric

Format One: This display gives the speedometer reading (in English or metric units), turn signal indication, high beam indication, transmission positions, outside air temperature, and compass heading.

Format Two: This display includes the information in Format One without the transmission information, the outside air temperature, and compass heading.

Format Three: This display includes the information in Format One along with a circular tachometer, but without outside air temperature and compass heading. All formats will show the turn-by-turn navigation information and provide details about the next driving maneuver to be made. When you near your destination, the HUD will display a distance bar that will empty the closer you get to your destination. All navigation

Chevrolet Camaro Owner Manual - 2011

Black plate (33,1)

information is provided to the HUD by the navigation radio or OnStar® service, for vehicles that have these features.

The HUD image displayed on the windshield will automatically dim and brighten to compensate for outside lighting. However, the HUD brightness control can still be adjusted as needed.

Instruments and Controls

5-33

The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see. Care of the HUD Clean the inside of the windshield as needed to remove any dirt or film that could reduce the sharpness or clarity of the HUD image. To clean the HUD lens, use a soft, clean cloth that has household glass cleaner sprayed on it. Wipe the HUD lens gently, then dry it. Do not spray cleaner directly on the lens because the cleaner could leak into the unit.

If You Cannot See the HUD Image When the Ignition Is On

Is anything covering the HUD lens? Is the HUD dimmer setting bright enough? Is the HUD image adjusted to the proper height?

. Are you wearing polarized

sunglasses?

. Still no HUD image? Check the

fuse in the instrument panel fuse block. See Instrument Panel Fuse Block on page 10‑47.

If the HUD Image Is Not Clear

Is the HUD image too bright? . Are the windshield and HUD

lens clean?

If the HUD image is not correct, contact your dealer. Keep in mind that the windshield is part of the HUD system.

Chevrolet Camaro Owner Manual - 2011

Black plate (34,1)

5-34

Instruments and Controls

Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action. For those you can press SET to acknowledge that you received the messages and to clear them. Some messages cannot be cleared because they are more urgent. These messages require action. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. Possible messages that can be displayed and some information about them, grouped by subject, are in the following information.

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑31 for more information.

SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.

Brake System Messages

BRAKE FLUID LOW This message is displayed when the brake fluid level is low; see Brake Fluid on page 10‑30. RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.

Chevrolet Camaro Owner Manual - 2011

Black plate (35,1)

Instruments and Controls

5-35

Compass Messages

Door Ajar Messages

CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑4. – – – Three dashes will be displayed if the compass needs service. See your dealer for service.

Cruise Control Messages

APPLY BRAKE BEFORE CRUISE If this message displays when attempting to activate cruise control, apply the brake pedal and try again. CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control on page 9‑43 for more information.

DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. PASSENGER DOOR OPEN This message will display when the passenger door is open. Close the door completely. TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.

Engine Cooling System Messages

A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10‑20.

Chevrolet Camaro Owner Manual - 2011

Black plate (36,1)

5-36

Instruments and Controls

ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature. HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10‑25.

Engine Oil Messages

CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑14 and Driver Information Center (DIC) on page 5‑25 for information on how to reset the system. See Engine Oil on page 10‑10 and Scheduled Maintenance on page 11‑2
for more information. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.

ENGINE OIL LOW — ADD OIL This message displays when the engine oil level is too low. Check the oil level. See Engine Oil on page 10‑10. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.

Chevrolet Camaro Owner Manual - 2011

Black plate (37,1)

Engine Power Messages

Fuel System Messages

Lamp Messages

Instruments and Controls

5-37

ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.

Key and Lock Messages

NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced.

AUTOMATIC LIGHT CONTROL ON This message is displayed when the automatic light control has been turned on. See Automatic Headlamp System on page 6‑4. AUTOMATIC LIGHT CONTROL OFF This message is displayed when the automatic light control has been turned off. See Automatic Headlamp System on page 6‑4. LEFT FRONT TURN INDICATOR FAILURE This message is displayed if the turn signal bulb needs to be replaced. See Headlamps, Front Turn Signal and Parking Lamps (Base Vehicle) on page 10‑39 or Headlamps, Front Turn Signal and Parking Lamps (Up-Level Vehicle) on page 10‑40 and Replacement Bulbs on page 10‑43 for more information.

Chevrolet Camaro Owner Manual - 2011

Black plate (38,1)

5-38

Instruments and Controls

LEFT REAR TURN INDICATOR FAILURE This message is displayed if the turn signal bulb needs to be replaced. See Taillamps, Turn Signal, and Stoplamps on page 10‑42 and Replacement Bulbs on page 10‑43 for more information. RIGHT FRONT TURN INDICATOR FAILURE This message is displayed if the turn signal bulb needs to be replaced. See Headlamps, Front Turn Signal and Parking Lamps (Base Vehicle) on page 10‑39 or Headlamps, Front Turn Signal and Parking Lamps (Up-Level Vehicle) on page 10‑40 and Replacement Bulbs on page 10‑43 for more information.

RIGHT REAR TURN INDICATOR FAILURE This message is displayed if the turn signal bulb needs to be replaced. See Taillamps, Turn Signal, and Stoplamps on page 10‑42 and Replacement Bulbs on page 10‑43 for more information. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.

Object Detection System Messages

PARK ASSIST OFF This message is displayed when the park assist system has been turned off. See Ultrasonic Parking Assist on page 9‑46.

SERVICE PARK ASSIST This message is displayed if there is a problem with the park assist system. Take the vehicle to your dealer for service.

Ride Control System Messages

STABILITRAK COMPETITIVE MODE (V8 Engine Only) This message displays when competitive mode is selected. See Competitive Driving Mode on page 9‑41 for more information. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service.

Chevrolet Camaro Owner Manual - 2011

Black plate (39,1)

Instruments and Controls

5-39

Safety Belt Messages

BUCKLE SEATBELT This message displays as a reminder when the safety belt is not buckled.

Anti-Theft Alarm System Messages

THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.

Service Vehicle Messages

SERVICE AC SYSTEM This message is displayed if there is a problem with the air conditioning system. Take the vehicle to your dealer for service.

SERVICE POWER STEERING This message is displayed if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE VEHICLE SOON This message is displayed if there is a problem with the vehicle. Take the vehicle to your dealer for service.

Tire Messages

CHECK XXX TIRE PRESSURE or TIRE PRESSURE LOW ADD AIR TO TIRE This message displays if the vehicle detects low pressure in one or more tires. This message also displays “Left Front”, “Right Front”, “Left Rear”, or “Right Rear” to indicate the location of the low tire.

SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak® system. If this message appears, try to reset the system. Stop; turn off the engine and remove the key from the ignition; open and close the driver door and wait for at least one minute. During this time you should notice the lights on the cluster turn off. After a minute has passed start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly.

Airbag System Messages

SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.

Chevrolet Camaro Owner Manual - 2011

Black plate (40,1)

5-40

Instruments and Controls

The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑23. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire Loading Information label. See Tires on page 10‑50, Vehicle Load Limits on page 9‑13, and Tire Pressure on page 10‑58. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑25. SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑62 for more information.

TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑62 for more information. TIRE PRESSURE SYSTEM RESET This message displays when resetting the TPMS. See Tire Pressure Monitor Operation on page 10‑62 for more information.

Transmission Messages

1 – 4 SHIFT This message displays when you can only shift from 1 (First) to 4 (Fourth) instead of 1 (First) to 2 (Second). See Manual Transmission on page 9‑34
for more information.

PRESS CLUTCH TO START This message displays when attempting to start a vehicle with a manual transmission without pressing on the clutch pedal. SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT DENIED This message displays when attempting to use the automatic transmission manual mode to shift to too low of a gear. See Manual Mode on page 9‑32 for more information. SHIFT TO PARK This message displays when the transmission needs to be shifted to park. This may appear when attempting to remove the key from the ignition if the vehicle is not in P (Park).

Chevrolet Camaro Owner Manual - 2011

Black plate (41,1)

Instruments and Controls

5-41

TRANSMISSION HOT – IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.

Vehicle Reminder Messages

ICE POSSIBLE DRIVE WITH CARE This message is displayed when ice conditions are possible.

TURN WIPER CONTROL TO INTERMITTENT FIRST This message is displayed when attempting to adjust the intermittent wiper speed without intermittent selected on the wiper control. See Windshield Wiper/Washer on page 5‑3.

Vehicle Speed Messages

DRIVER SELECTED SPEED LIMIT EXCEEDED This message is displayed when the vehicle speed is greater than the set speed. See “Speed Warning” under Driver Information Center (DIC) on page 5‑25.

Window Messages

OPEN, THEN CLOSE DRIVER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑15 for more information. OPEN, THEN CLOSE PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑15 for more information.

Chevrolet Camaro Owner Manual - 2011

Black plate (42,1)

5-42

Instruments and Controls

Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings Menu. MENU/SELECT Knob: Press the center of this knob to enter the menus and select menu items. Turn the knob to scroll through the menus. 0 BACK: Press to exit or move backwards in a menu.

Entering the Personalization Menus 1. Press the CONFIG button to

access the Configuration Settings menu.

2. Turn the MENU/SELECT knob to

highlight Vehicle Settings.

3. Press the center of the

MENU/SELECT knob to select the Vehicle Settings menu.

The following list of menu items will be available: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems

Language Lighting

. Power Door Locks . Remote Lock/Unlock . Return to Factory Settings

Turn the MENU/SELECT knob to highlight the menu. Press the knob to select it. Each of the menus is detailed in the following information. Climate and Air Quality Select the Climate and Air Quality menu and the following will be displayed: . Remote Start Heated Seats

Remote Start Heated Seats When on, this feature will turn the heated seats on when using remote start. Press the MENU/SELECT knob when Remote Start Heated Seats is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Chevrolet Camaro Owner Manual - 2011

Black plate (43,1)

Instruments and Controls

5-43

Press the MENU/SELECT knob when Personalization by Driver is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu. Collision/Detection Systems Select the Collision/Detection Systems menu and the following will be displayed: . Park Assist

Park Assist This allows the Ultrasonic Parking Assist feature to be turned on or off. Press the MENU/SELECT knob when Park Assist is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Language Select the Language menu and the following will be displayed: . English French . Spanish Turn the MENU/SELECT knob to select the language. Press the knob to confirm and go back to the last menu. Lighting Select the Lighting menu and the following will be displayed: . Exit Lighting . Vehicle Locator Lights

Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Chime Volume . Personalization by Driver

Chime Volume This allows the selection of the chime volume level. Press the MENU/SELECT knob when Chime Volume is highlighted. Turn the knob to select Normal or High. Press the knob to confirm and go back to the last menu.

Personalization by Driver This allows selecting whether he personalization settings are specific to each driver or the same no matter which key was used to enter and start the vehicle.

Chevrolet Camaro Owner Manual - 2011

Black plate (44,1)

5-44

Instruments and Controls

Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the MENU/SELECT knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press the knob to confirm and go back to the last menu.

Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. Press the MENU/SELECT knob when Vehicle Locator Lights is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Power Door Locks Select Power Door Locks and the following will be displayed: . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock

Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If off is selected, the Delayed Door Lock menu will be available. Press the MENU/SELECT knob when Auto Door Unlock is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park) (automatic transmission) or when the key is removed from the ignition (manual transmission). Press the MENU/SELECT knob when Auto Door Unlock is highlighted. Turn the knob to select All Doors, Driver Door, or Off. Press the knob to confirm and go back to the last menu.

Delayed Door Lock When on, this feature will delay the locking of the doors. To override the delay, press the power door lock on the driver door. Press the MENU/SELECT knob when Delayed Door Lock is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu.

Chevrolet Camaro Owner Manual - 2011

Black plate (45,1)

Instruments and Controls

5-45

Remote Lock/Unlock Select Remote Lock/Unlock and the following will be displayed: . Unlock Feedback (Lights)

Locking Feedback

. Door Unlock Options

Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press the MENU/SELECT knob when Unlock Feedback (Lights) is highlighted. Turn the knob to select Flash Lights or Off. Press the knob to confirm and go back to the last menu.

Locking Feedback This allows selection of what type of feedback is given when unlocking the vehicle with the RKE transmitter. Press the MENU/SELECT knob when Locking Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press the knob to confirm and go back to the last menu.

Door Unlock Options This allows selection of which doors will unlock when pressing the unlock button on the RKE transmitter. Press the MENU/SELECT knob when Door Unlock Options is highlighted. Turn the knob to select All Doors or Driver Door Only. Press the knob to confirm and go back to the last menu. Return to Factory Settings Select Return to Factory Settings to return all of the vehicle personalization to the default settings. Turn the knob to select Yes or No. Press the knob to confirm and go back to the last menu.

Chevrolet Camaro Owner Manual - 2011

Black plate (46,1)

5-46

Instruments and Controls

Universal Remote System See Radio Frequency Statement on page 13‑19 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-210/220/310.

Universal Remote System Programming

If the vehicle has this feature, you will see these buttons with one LED indicator next to them in the overhead console.

This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system.

Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal.

Chevrolet Camaro Owner Manual - 2011

Black plate (47,1)

Instruments and Controls

5-47

2. At the same time, press

3. Press and hold for five seconds

and hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons. Some entry gates and garage door openers may require substitution of Step 2 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.

the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation. If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4 through 6.

Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated. To program up to three devices: 1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).

Chevrolet Camaro Owner Manual - 2011

Black plate (48,1)

5-48

Instruments and Controls

If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4
through 6. It may be helpful to have another person assist with the remaining Steps 4
through 6.

6.

Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, and then release.

The Universal Remote system should now activate the garage door. To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.”

“Learn” or “Smart” Buttons 4. After Steps 1 through 3 have

been completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head unit). The name and color of the button may vary by manufacturer.

5. Firmly press and release the

“Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 6.

Chevrolet Camaro Owner Manual - 2011

Black plate (49,1)

Instruments and Controls

5-49

Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by

using the “Programming the Universal Remote System” procedures, regardless of where you live, replace Step 2 under “Programming the Universal Remote System” with the following: 2. Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.

Universal Remote System Operation

Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the

two outside buttons until the indicator light begins to flash. This should take about 10 seconds.

2. Release both buttons.

Chevrolet Camaro Owner Manual - 2011

Black plate (50,1)

5-50

Instruments and Controls

Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired

Universal Remote system button. Do not release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 of the section “Programming the Universal Remote System.”

If you have questions or need help programming the Universal Remote system, call 1‐800‐355‐3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑4 or Customer Assistance Offices (Mexico) on page 13‑5.

Chevrolet Camaro Owner Manual - 2011

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lighting Exterior Lamp Controls

Exterior Lamp Controls . . . . . . . . 6-1
Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-3
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . 6-3

Automatic Headlamp

System . . . . . . . . . . . . . . . . . . . . . . 6-4
Hazard Warning Flashers . . . . . 6-5
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-5
Front Fog Lamps . . . . . . . . . . . . . . 6-5

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-6
Dome Lamps . . . . . . . . . . . . . . . . . 6-6

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Theater Dimming . . . . . . . . . . . . . . 6-6
Battery Load Management . . . . 6-7
Battery Power Protection . . . . . . 6-7

The exterior lamps control is located on the instrument panel, on the outboard side of the steering wheel. It controls the following systems: . Headlamps . Sidemarker Lamps . Parking Lamps

Taillamps License Plate Lamps Instrument Panel Lights Fog Lamps

. Daytime Running Lamps (DRL)

Lighting

6-1

The exterior lamps control has four positions: P (Off): Briefly turn to this position to turn the automatic light control off or on again. When released, the control returns to the AUTO position. AUTO (Automatic): Turns the headlamps on automatically at normal brightness, together with the following: . Parking Lamps

Taillamps

. Sidemarker Lamps