Download PDF Manual


When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. Don’t mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid. Fill your washer fluid tank only three-quarters full when it’s very cold. This allows for expansion if freezing occurs, which could damage the tank if it is completely full. Don’t use engine coolant (antifreeze) in your windshield washer. It can damage your washer system and paint.


6-32


Brakes Brake Fluid


Your brake master cylinder reservoir is here. It is filled with DOT-3 brake fluid. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the fluid level goes back up. The other reason is that fluid is leaking out


of the brake system. If it is, you should have your brake system fixed, since a leak means that sooner or later your brakes won’t work well, or won’t work at all. So, it isn’t a good idea to “top off’ your brake fluid. Adding brake fluid won’t correct a leak. If you add fluid when your linings are worn, then you’ll have too much fluid when you get new brake linings. You should add (or remove) brake fluid, as necessary, only when work is done on the brake hydraulic system.


A CAUTIOP’: If you have too much brake fluid, it can spill on the engine. The fluid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system.


Refer to the Maintenance Schedule to determine when to check your brake fluid. See “Periodic Maintenance Inspections’’ in the Index.


6-33


What to Add When you do need brake fluid, use only DOT-3 brake fluid -- such as Delco Supreme 11 No. 12377967). Use new brake fluid from a sealed container only. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This will help keep dirt from entering the reservoir.


(GM Part


I A CAUTION:


With the wrong kind of fluid in your brake system, your brakes may not work well, or they may not even work at all. This could cause a crash. Always use the proper brake fluid.


Checking Brake Fluid


You can check the brake fluid without taking off the cap. Just look at the brake fluid reservoir. The fluid level should be above the plastic seam in the reservoir. If it isn't, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the plastic seam, near the base of the filler neck.


6-34


NOTICE:


Using the wrong fluid can badly damage brake system parts. For example, just a few drops of mineral-based oil, such as engine oil, in your brake system can damage brake system parts so badly that they’ll have to be replaced. Don’t let someone put in the wrong kind of fluid. If you spill brake fluid on your vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on your vehicle. If you do, wash it off immediately. See “Appearance Care” in the Index.


Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).


The brake wear warning sound means that soon your brakes won’t work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.


I NOTICE:


Continuing to drive with worn-out brake pads could result in costly brake repair.


6-35


The park brake system has separate brake linings that do not self adjust for wear. If the park brake lever pulls up more than the normal eighteen clicks, the parking brakes may need adjustment. See your dealer. Replacing Brake System Parts The braking system on a modern vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system -- for example, when your brake linings wear down and you have to have new ones put in -- be sure you get new approved GM replacement parts. If you don’t, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change -- for the worse. The braking performance you’ve come to expect can change in many other ways if someone puts in the wrong replacement brake parts.


Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes. When you have the front brake pads replaced, have the rear brakes inspected, too. Brake linings should always be replaced as complete axle sets. See “Brake System Inspection” in Section 7 of this manual under Part C “Periodic Maintenance Inspections.” Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you make a moderate brake stop, your disc brakes adjust for wear. If you rarely make a moderate or heavier stop, then your brakes might not adjust correctly. If you drive in that way, then -- very carefully -- make a few moderate brake stops about every 1,000 miles (1 600 km), so your brakes will adjust properly.


6-36


Battery Every new Chevrolet has a Delco Freedom@ battery. You never have to add water to one of these. When it’s time for a new battery, we recommend a Delco Freedom battery. Get one that has the replacement number shown on the original battery’s label. Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, remove the black, negative (-) cable from the battery. This will help keep your battery from running down.


I A CAUTION:


Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you aren’t careful. See “Jump Starting” in the Index for tips on working around a battery without getting hurt.


Ids.


Contact your dealer to learn how to prepare your vehicle for longer storage pe Also, for your audio system, see “Theft-Deterrent Feature” in the Index. Bulb Replacement For the proper type of replacement bulb, see “Replacement Bulbs” in the Index. Halogen Bulbs ‘h C WTION: -


Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.


6-37


Headlamns


light, check


Before replacing a headlamp that does not to make sure that the wiring connector is securely fastened to it. See "Replacement Bulbs" in the Index to check type of headlamp you need to use before you begin to replace the headlamp. You must replace a headlamp with one that is exactly the same. 1. Open the hood. 2. Locate the affected headlamp.


6-38


3.


4. 5.


to the left


Press and turn the base a quarter-turn (counterclockwise). (See arrows). Remove the socket with the burned lamp. Replace the bulb and insert the socket into the headlamp.


Be careful not to move the aiming screws when you replace the headlamp. If the headlamp being replaced was properly aimed, the new one will be also if it is properly installed.


If your vehicle is damaged in an accident and the headlamp aim seems to be affected, see your dealer. Headlamps on damaged vehicles may require recalibration of the horizontal aim by your dealer. Front Turn Signal 1. Using a screwdriver, remove the plastic screws from the trap door under the vehicle. Move the trap door out of the way.


2. Turn and pull out the socket and the bulb. 3. Pull out the bulb. 4. Reverse the steps with a new bulb.


Center High-Mounted Stoplamp


Replacing the bulb: 1. Remove the two screws in the stoplamp lens. 2. Gently pull the assembly out and remove the bulb


from the back of the assembly.


3. Reverse the steps with a new bulb.


6-39


Rear Lamps To change any rear bulb, you have to remove the entire housing. 1. Remove the trim panel from the side that you are


replacing the bulb.


2. Pull the carpet back.


3. Remove the wing nuts.


6-40


4. Pull the assembly off from the outside. 5. To remove a socket with a tab, press the tab and turn the socket to the left (counterclockwise). To remove a socket without a tab, turn the socket to the left (counterclockwise).


6. To remove the bulb, pull the bulb from the socket. 7. Reverse the steps with a new bulb.


Rear Sid marker


Replacing a rear sidemarker bulb: 1. Remove the screw from the sidemarker assembly. 2. To pull out the bulb housing, tilt the housing to


remove the tabbed end.


3. Turn socket to the left (counterclockwise) and pull


out the socket and the bulb.


4. Reverse the steps with a new bulb,


6-41


2.


To replace the wiper blade element, refer to the wiper blade assembly replacement instructions. To replace the element follow these steps: 1.


Locate the heel end of the wiper blade assembly that has the two notches held by the wiper blade claw. Hold the wiper blade assembly with one hand and pull the element gently with the other hand. (Replacement blade elements have three plastic caps which retain two metal flexor strips. Do not remove these caps before the element At the heel end of the wiper blade assembly, notched end of blade element last, slide the blade element into the blade claw sets. The plastic retainer caps will be forced off as the element is fully inserted. Make sure that all the claw sets are properly engaged in the slots of the blade element. Install the wiper blade assembly on the wiper arm. 4. For information on wiper blade replacement length and type, see “Capacities and Specifications’’ in the Index.


is installed).


3.


Wiper Blade Assembly Replacement Replacement blades come in different types and are removed in different ways. To remove the wiper blade assembly: 1. Lift the wiper arm until it locks into an


upright position.


2. Press the locking tab in while sliding the blade


assembly down.


Wiper Blade Element Replacement


6-42


Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Chevrolet Warranty booklet for details.


’ Poorly maintained and improperly used tires are dangerous. 0 Overloading your tires can cause


overheating as a result of too much friction. You could have an air-out and a serious accident. See “Loading Your Vehicle” in the Index.


CAUTION: (Continued)


Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. Overinflated tires are more likely to be impact -- such as when you hit a pothole. cut, punctured or broken by a sudden


Keep tires at the recommended pressure. Worn, old tires can cause accidents. If your tread is badly worn, or if your tires have been damaged, replace them.


See “Inflation -- Tire Pressure” in this section


for inflation pressure adjustment for higher speed driving.


6-43


Inflation -- Tire Pressure The Tire-Loading Information label, which is on the driver’s door, shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). If you’ll be driving at speeds higher than 100 mph (160 km/h) where it is legal, raise the cold inflation pressure of each tire to 35 psi (240 kPa). When you end this very high-speed driving, reduce the cold inflation pressures to those listed on the Tire-Loading Information label.


6-44


NOTICE:


Don’t let anyone tell you that underinflation or overinflation is all right. It’s not. If your tires don’t have enough air (underinflation), you can get the following:


Too much flexing Too much heat


0 Tire overloading 0 Bad wear 0 Bad handling


Bad fuel economy.


If your tires have too much air (overinflation), you can get the following: 0 Unusual wear 0 Bad handling


Rough ride


0 Needless damage from road hazards.


When to Check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inflated simply by lookrng at them. Radial tires may look properly inflated even when they’re underinflated. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. Tire Inspection and Rotation Tires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires” and “Wheel Replacement” later in this section for more information.


The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The first rotation is the most important. See “Scheduled Maintenance Services” in the Index for scheduled rotation intervals.


If you don’t have P245/5OZR16 Goodyear Eagle GS-C tires or P275/4OZR17 Goodyear Eagle F1-GS tires, use the rotation pattern shown above for your tires.


6-45


+ I1


After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” in the Index.


-I-


If you have P24950ZR16 Goodyear Eagle GS-C tires or P275/40ZR17 Goodyear Eagle F1 -GS tires, they must roll in a certain direction for the best overall performance. The direction is shown by an arrow on the sidewall. Because these tires are directional, they should be rotated as shown here. These tires should only be moved from front to rear and rear to front on the same side of the vehicle. Don’t include the compact spare tire in your tire rotation.


Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off. (See “Changing a Flat Tire” in the Index.)


When It’s Time for New Tires


One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.


You need a new tire if any of the following statements are true:


YOU can see the indicators at three or more places around the tire. You can see cord or fabric showing through the tire’s rubber. The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.


The tire has a bump, bulge or split. The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage.


Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle. If your tires have an all-season tread design, the TPC number will be followed by an “MS” (for mud and snow). If you ever replace your tires with those not having a TPC Spec number, make sure they are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires.


6-47


'--I Quality Grading


Uniform The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to Federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.


Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. It's all right to drive with your compact spare, though. It was developed for use on your vehicle.


If you use bic 'ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.


6-48


Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.


Traction -- A, B, C


The traction grades, from highest to lowest, are A, B, and C , and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turning) traction.


Temperature -- A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


6-49


Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keer> coming. loose. the wheel. wheel bolts and wheel nuts s h h d be &placed. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need.


Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your Chevrolet model.


I Using the wrong replacement wheels, wheel bolts


or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.


6-50


I NOTICE:


The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance and tire or tire chain clearance to the body and chassis.


See “Changing a Flat Tire” in the Index for more information.


Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause an accident. If you have to replace a wheel, use a new GM original equipment wheel.


rire Chains


NOTICE:


If your vehicle has P235/55R16, P245/50ZR16 or P275/40ZR17 size tires, don’t use tire chains. They can damage your vehicle because there’s not enough clearance. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it’s contacting your vehicle, and don’t spin your wheels.


NOTICE: (Continued)


6-51


NOTICE: (Continued)


If you do find traction devices that will fit, install them on the rear tires. If you have other tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the rear tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.


Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flame if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings


and instructions. And always open your doors or windows when you’re cleaning the inside. Never use these to clean your vehicle: 0 Gasoline 0 Benzene Naphtha Carbon Tetrachloride


0 Acetone 0 Paint Thinner 0 Turpentine 0 Lacquer Thinner 0 Nail Polish Remover They can all be hazardous -- some more than others -- and they can all damage your vehicle, too. Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle:


Alcohol Laundry Soap


0 Bleach 0 Reducing Agents


Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl or leather with a clean, damp cloth. Your dealer has two cleaners, Multi-Purpose Interior Cleaner and Capture Non-Solvent Dry Spot and Soil Remover. They will clean normal spots and stains very well. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Here are some cleaning tips:


Always read the instructions on the cleaner label.


0 Clean up stains as soon as you can -- before they set.


Carefully scrape off any excess stain. Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. If a ring forms after spot cleaning, clean the entire area immediately or it will set.


Using Multi-Purpose Interior Cleaner on Fabric 1. Vacuum and brush the area to remove any loose dirt. 2. Always clean a whole trim panel or section. Mask


surrounding trim along stitch or welt lines.


3. Mix powdered cleaner following the directions on


the container label to form thick suds.


4. Use suds only and apply with a clean sponge. Don’t


saturate the material and don’t rub it roughly.


5. As soon as you’ve cleaned the section, use a sponge


to remove the suds.


6. Wipe cleaned area with a clean, damp towel or cloth. 7. Wipe with a clean cloth and let dry.


6-53


Fabric Protection Your vehicle has upholstery and carpet that has been treated with Scotchgard" Fabric Protector, a 3M product. It protects fabrics by repelling oil and water, which are the carriers of most stains. Even with this protection, you still need to clean your upholstery and carpet often to keep it looking new. Further information on cleaning is available by calling 1-800-433-3296 (in Minnesota, 1-800-642-6167). Cleaning Vinyl Use warm water and a clean cloth.


Rub with a clean, damp cloth to remove dirt. You may have to do it more than once. Things like tar, asphalt and shoe polish will stain if you don't get them off quickly. Use a clean cloth and a vinyl/leather cleaner. See your dealer for this product.


2.


3.


Fabric Cleaning Problems


Spec- I Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: 1.


Carefully scrape off excess stain, then sponge the soiled area with cool water. If a stain remains, follow the multi-purpose interior cleaner instructions described earlier. If an odor lingers after cleaning vomit or urine, treat the area with a waterhalung soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water. Let dry.


4. Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: 1. Carefully scrape off excess stain. 2. First, clean with cool water and allow to


dry completely.


3. If a stain remains, follow instructions for


Multi-Purpose Interior Cleaner.


6-54


Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth. Then, let the leather dry naturally. Do not use heat to dry. 0 For stubborn stains, use a leather cleaner. See your


dealer for this product.


0 Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather.


0 Soiled or stained leather should be cleaned


immediately. If dirt is allowed to work into the finish, it can harm the leather.


Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.


Cleaning Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface finish. Care of Safety Belts Keep belts clean and dry.


Do not bleacn or aye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.


Cleaning Glass Surfaces Glass should be cleaned often. GM Glass Cleaner (GM Part No. 1050427) or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass. Don’t use abrasive cleaners on glass, because they may cause scratches. Avoid placing decals on the inside rear window, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rear window, an electric defogger element may be damaged. Any temporary license should not be attached across the defogger grid. Cleaning the Outside of the Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with GM Windshield Cleaner, Bon Ami@ Powder (non-scratching glass cleaning powder), GM Part No. 105001 1. The windshield is clean if beads do not form when you rinse it with water.


Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants” in the Index.) Cleaning a Removable Roof Panel Special care is necessary when cleaning, removing and/or storing the roof panel.


Flush with water to remove dust and dirt, then dry the panel.


0 Clean the panel with GM Glass Cleaner. Leave the cleaner on the panel for one minute, then wipe the panel with a soft, lint-free cloth.


0 Don’t use abrasive cleaning materials.


6-56


Cleaning the Outside of Your Vehicle The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps or chemical detergents. Use liquid hand, dish or car washing (mild detergent) soaps. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.


Cleaning Exterior LampsLenses Use lukewarm or cold water, a soft cloth and a liquid hand, dish or vehicle washing (mild detergent) soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.) Your Chevrolet has a “basecoatklearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoatklearcoat paint finish.


NOTICE:


Machine compounding or aggressive polishing on a basecoatklearcoat paint finish may dull the finish or leave swirl marks.


6-57


Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Cleaning Your Convertible Top Your convertible top should be cleaned often. If you use an automatic car wash, use one with water jets and hanging cloths. High pressure car washes may cause water to enter your vehicle. When you hand wash the top, do it in partial shade. Use a mild soap, lukewarm water and a soft sponge. A chamois or cloth may leave lint on the top, and a brush can chafe the threads in the top fabric. Don’t use detergents, harsh cleaners, solvents or bleaching agents.


Wet the entire vehicle and wash the top evenly to avoid spots or rings. Let the soap remain on the fabric for a few minutes. When the top is really dirty, use a mild foam-type cleaner. Thoroughly rinse the entire vehicle, then let the top dry in direct sunlight. To protect the convertible top: 0 After you wash the vehicle, make sure the top is


completely dry before you lower it.


0 Don’t get any cleaner on the vehicle’s painted finish;


it could leave streaks.


0 If you decide to go through an automatic car wash, ask the manager if the equipment could damage your top.


Cleaning Aluminum or Chrome Wheels (If Equipped) Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.


6-58


The surface of these wheels is similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, abrasive polishes, abrasive cleaners or abrasive cleaning brushes on them because you could damage the surface. You may use chrome polish on chrome wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Don’t take your vehicle through an automatic car wash that has silicon carbide tire cleaning brushes. These brushes can also damage the surface of these wheels. Cleaning Tires To clean your tires, use a stiff brush with a tire cleaner. materials available


Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to the parts repaired or replaced to restore corrosion protection. Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. Minor chips and scratches can be repaired with touch-up


from your dealer or other service


outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.


NOTICE:


When applying a tire dressing always take care to wipe off any overspray or splash from all painted surfaces on the body or wheels of the vehicle. Petroleum-based products may damage the paint finish.


6-59


Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, accelerated corrosion (rust) can occur on the underbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and other debris can collect. Dirt packed in closed areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.


ical Pail . .1 PC


. .


hg


Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, Chevrolet will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.


6-60


Appearance Care Materials Chart


1050172 1050173 1050174


1052918**


SIZE


DESCRIPTION


USAGE


Exterior polishing cloth


Polishing Cloth - Wax Treated Tar and Road Oil Remover Removes tar, road oil and Chrome Cleaner and Polish Use


x 25 in. 23 in. 16 oz. (0.473 L) 16 oz. (0.473 L) 16 oz. (0.473 L) White Sidewall Tire Cleaner Removes soil and black marks from whitewalls 32 oz. (0.946 L) 23 oz. (0.680 L) 16 oz. (0.473 L) 8 oz. (0.237 L)


Vinyl Cleaner Cleans vinyl tops, Glass Cleaner Removes


Wash Wax Concentrate


Annor All” Protectant


dirt, grime, smoke and fingerprints Cleans and lightly waxes


on chrome, stainless steel, nickel, copper and


I Protects leather, wood, acrylics, Plexiglas m , plastic,


uphokeryand convertibletops


asphat


_____


brass


~~ _ -


~ -


rubber and vinyl


Multi-Purpose Interior Cleans carpets, seats, interior trim, door panels


Capture Dry Spot Remover


and


Cleaner Wheel Spray Cleaner on rinse and with water


16 oz. (0.473 L) floor 16 oz. (0.473 L) 8 02. (0.237 L) 16 oz. (0.473 L)


1052925 mats 1052929 1052930 12345002 1234572 1 12345725 12377964 Cleaner Wax 12377966 12377984 Surface Cleaner See your General Motors Parts Department for these products. See “Fluids and Lubricants” in the Index.


12 oz. (0.354 L) 16 oz. (0.473 L) 16 oz. (0.473 L) 16 oz. (0.473 L)


Armor All TM Cleaner without Chamois Shines vehicle


scratching Synthetic Silicone Tire Shine Finish Enhancer


2.5 sq. ft.


Attracts, absorbs and removes soils


Cleans and shines a variety of surface types


Spray on tire shine


Removes dust, fingerprints and surface contaminants Removes light scratches and oxidation and protects finish Removes contaminants, blemishes and swirl marks


**Not recommended for use on instrument panel vinyl.


, _ _ . ~


- _ -


- - .-


6-61


Vehicle Identification Number (VIN)


the model designation, paint information and


0 a list of all production options and special


equipment.


L1


This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The 8th character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts. Service Parts Identification Label You’ll find this label inside your console storage compartment. It’s very helpful if you ever need parts. On this label is:


to order


your VIN,


Be sure that this label is not removed from the vehicle. Electrical System


iquipment


Ad( r- NOTICE:


Don’t add anything electrical to your vehicle i unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.


Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see “Servicing Your Air Bag-Equipped Chevrolet” in the Index.


Headlamps The headlamp wiring is protected by a circuit breaker. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked right away. Windshield Wipers The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed. Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links in the wiring itself. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the correct size. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one of the correct value. Just pick some feature of your vehicle that you can get along without -- like the radio or cigarette lighter -- and use its fuse, if it is the size you need. Replace it as soon as you can.


6-63


1


STOPIHAZARD


TURN BIU


FUSE USAGE CHART


SO


TAIL LPS


51-1


9-1


GAUGES


Q 1


IGN


ACCY


PWR


HVAC


1 0 1 1 1


AIR BAG CIGIACCY


BATT


WIPER/WASH


ACCY


IP DIMMER


RADIO ACCY


COURTESY


DEFOGISEATS


WINDOWS 17 I


RADIO


Fuse STOP/HAZARD Hazard Flasher, Brake


Usage


Switch Assembly Traction ControVSecond Gear Start Switch, Back-up Lamp Switch, Turn Flasher, Daytime Running Lamps (Dm) Module Delco Monsoon Radio Amplifier, Remote CD Player (Trunk)


TURN B/U


RADIO ACCY


6-64


Fuse TAIL LPS


HVAC


PWR ACCY


COURTESY GAUGES


AIR BAG


CIG/ACCY


Usage Daytime Running Lamps (DRL) Module, Headlamp Switch HVAC Selector Switch, Rear Defogger SwitcWTimer Park Lamp Relay, Hatch Release Relay, Power Mirror Switch, Radio, Shock Sensor, Instrument Cluster Body Control Module (BCM) Body Control Module (BCM), Brake Switch Assembly (BTSI), Instrument Cluster, Daytime Running Lamps (DRL) Module, Auxiliary Accessory Wire Air Bag System, Dual Pole Arming Sensor Cigarette Lighter, Data Link Connector (DLC), Auxiliary Accessory Wire


Fuse DEFOGEEATS


WIPEWASH


WINDOWS


IP DIMMER


RADIO


Usage Rear Defogger Switch/Timer, Power Seats Wiper Motor Assembly, Wipermasher Switch Power Windows Switch (RH, LH), Express Down Module, Convertible Top Switch Door Illumination Lamp (LH, RH), Headlamp Switch, Fog Lamp Switch, Instrument Cluster, HVAC Control Assembly, PRNDL Illumination Lamp, Ashtray Lamp, Radio, Steering Wheel Controls-Radio, Rear Window Defogger Switch/Timer, Traction Control (ASR) Second Gear Start Switch Body Control Module (BCM), Radio, Amplifier, Steering Wheel Controls-Radio


6-65


Underhood Electrical Center Fuses


ABS BAT SOL


TCS BAT


COOL FAN


PCM BAT


000


FUEL PUMP


LH HOW OR


AIR PUMP


RH HDLP DR


HORN r FAN $43


15305529 A


---


1 -


The two underhood fuse and relay centers are located in the engine compartment. Open the cover to expose the fuses.


6-66


Fuse and Relay Center 1


Fuse ABS BAT SOL TCS BAT COOL FAN PCM BAT FUEL PUMP AIR PUMP


Usage Anti-Lock Brake System Traction Control System Cooling Fan Control Powertrain Control Module Fuel Pump Air Pump Relay and Bleed Valve


ENG


INJ


Fuse LH HDLP RH HDLP HORN ABS BAT-1 H/L DR HORN ABS BAT-2


COOL FAN


SEN


Usage Headlamp Door and Module Headlamp Door and Module Horn Relay Anti-Lock Brake System Module Horn and Headlamp Doors Anti-Lock Brake and Traction Control System Cooling Fan Relays


INJ


on0 on0


ABS IGN


STRTR


PCM IGN


ENG CTRL


A/C CRUISE


15305530 A


FRC 2


Relay FOG LAMP HORN COOLING FAN #3 COOLING FAN #2 COOLING FAN #1


Fuse INJ


INJ


Fuse and Relay Center 2


Usage Fuel Injectors (Not Used for V6) (LH Injectors for V8 and Ignition Module) Fuel Injectors (All for V6) (LH Injectors for V8 and Ignition Module)


6-67


Usage HVAC Blower Control and Relay Ignition Switch, Relay and Starter Enable Relay Instrument Panel Fuse Center


Fuse ENG SEN


STRTR


ABS IGN PCM IGN ENG CTRL


Usage Mass Air Flow, Heated Oxygen Sensor, Skip Shift Solenoid (V8 Only), Reverse Lockout Solenoid, Brake Switch Powertrain Control Module and Clutch Pedal Switch Anti-Lock Brake System Module Powertrain Control Module Ignition Module (V6 Only), Automatic Transmission and Charcoal Canister Purge Solenoid


A/C CRUISE Air Conditioning Compressor Relay, Cruise Control Switches and Module Engine Controls, Fuel Pump, PCM, A.I.R. and Cooling Fans


ENG CTRL


Fuse I/P- 1 IGN


UP- 2


Relay AIR SOL AIR PUMP A/C COMP FUEL PUMP STARTER IGN


6-68


Replacement Bulbs Back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3155 Center High-Mounted Stoplamp . . . . . . . . . . . . . 92 1 Front Parking and Turn Signal ............. 3157K Headlamp (Low-Beam) ................... 9006 Headlamp (High-Beam) . . . . . . . . . . . . . . . . . . 9005 Sidemarker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 ............................... 194 Tail Only Tail/Stop/Turn .......................... 3057 Capacities and Specifications Engine Type VIN Engine Code K ...................... V6 VIN Engine Code G ...................... V8 Fuel Delivery .................... Fuel Injection


Valve Arrangement . . . . . . . . . . . . . . . . . . . . In-Head Piston Displacement VIN Engine Code K . . . . . . . . . 23 1 CID (3791 cc) VIN Engine Code G . . . . . . . . . 350 CID (5735 cc) Firing Order VIN Engine Code K .............. 1-6-5-4-3-2 VIN Engine Code G . . . . . . . . . . . 1-8-7-2-6-5-4-3 Wheel Nut Torque . . . . . . . . . . . 100 lb-ft (140 Nnm) Thermostat Temperature Specification . . . . . . . . . . . . . . . . . . . 180°F (82°C) Windshield Wiper Blade Replacement Type ................................. Length ....................


hook 24 inches (610 cm)


Capacities (Approximate) The following approximate capacities are given in U.S. and metric conversions. ....... Please refer to


“Recommended Fluids and Lubricants” in the Index for more information.


Air Conditioning? ............ See the refrigerant


information label under the hood.


Automatic Transmission Drain and Refill ............... 5 quarts (4.7 L)* Overhaul VIN Engine Code K ...... 8.8 quarts (8.3 L)* VIN Engine Code G .... 10.8 quarts (10.2 L)*


Cooling System


VIN Engine Code K With Manual Transmission . . 12.5 quarts (11.8 L) With Automatic Transmission ............ 12.3 quarts (1 1.6 L)


6-70


VIN Engine Code G


. 15.3 quarts (14.5 L) With Manual Transmission With Automatic Transmission ........... 15.1 quarts. (14.3 L)


Crankcase


With Oil and Filter Change 3800 (VIN K) ........... 4.5 quarts (4.2 L)** 5.7L (VIN G) ............ 5.5 quarts (5.2 L)** Fuel Tank .................. 15.5 gallons (58.7 L) Manual Transmission Five-Speed ................ 3.4 quarts (3.2 L)* Six-Speed ................... 4 quarts (3.8 L)* Rear Axle Lubricant ......... 1.75 quarts (1.7 L)


* Recheck fluid level after filling. See “Automatic


Transmission Fluid” or “Manual Transmission Fluid” in the Index.


** Recheck the oil level after filling. See “Engine Oil”


in the Index.


Air Conditioning Refrigerants Not all air conditioning refrigerants are the same. If the air conditioning system in your vehicle needs refrigerant, be sure the proper refrigerant is used. If you’re not sure, ask your dealer.


Vehicle Dimensions


193.5 inches (49 1.5 cm) 74.1 inches (1 88.3 cm) 51.3 inches (130.3 cm) 10 1.1 inches (256.6 cm) 60.7 inches (154.1 cm) 60.6 inches (153.9 cm)


Length Width Height Wheelbase Front Tread Rear Tread Replacement Parts Air Cleaner Filter ...................... A1163C Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75-60 Engine Oil Filter VIN Engine Code K .................... PF47 VIN Engine Code G . . . . . . . . . . . . . . . . . . . . PF25 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GF578 PCV Valve VIN Engine Code K . . . . . . . . . . . . . . . . . CV892C VIN Engine Code G . . . . . . . . . . . . . . . . . CV895C Radiator Cap ........................... RC24 Spark Plug VIN Engine Code K . . , . 41-921 (0.060 inch Gap) VIN Engine Code G . . . . 41-931 (0.060 inch Gap)


6-71


b NOTES


6-72


0 Section 7 Maintenance Schedule


This section covers the maintenance required for your Chevrolet. Your vehicle needs these services to retain its safety, dependability and emission control performance.


7-2 7-3 7-4 7-5 7-5 7-6


Your Vehicle and the Environment How This Section is Organized Part A: Scheduled Maintenance Services Short TripKity Definition Short TripKity Intervals Long TripKity Definition


7-6 7-32 7-36 7-37 7-39


Long TripKity Intervals Part B: Owner Checks and Services Part C: Periodic Maintenance Inspections Part D: Recommended Fluids and Lubricants Part E: Maintenance Record


7-1


Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, please maintain your vehicle properly.


RECOMMENDED


LEVEL AND CHANGE AS


IMPORTANT: KEEP ENGINE OIL AT THE PROPER


HI protection


Plan


Have you purchased the GM Protection Plan ? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet, or your Chevrolet dealer for details.


7-2


How This Section is Organized The remainder of this section is divided into five parts: “Part A: Scheduled Maintenance Services” shows what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.


A CAUTION:


Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, have a qualified technician do the work.


If you are skilled enough to do some work on your vehicle, you will probably want to get the service information. See “Service and Owner Publications” in the Index.


“Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what you can easily do to help keep your vehicle in good condition. “Part C: Periodic Maintenance Inspections” explains important inspections that your dealer’s service department or another qualified service center should perform. “Part D: Recommended Fluids and Lubricants” lists some recommended products to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” provides a place for you to record the maintenance performed on your vehicle. Whenever any maintenance is performed, be sure to write it down in this part. This will help you determine when your next maintenance should be done. In addition, it is a good idea to keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.


7-3


The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. These schedules are for vehicles that: 0 carry passengers and cargo within recommended


limits. You will find these limits on your vehicle’s Tire-Loading Information label. See “Loading Your Vehicle’’ in the Index.


0 are driven on reasonable road surfaces within legal


driving limits.


0 use the recommended fuel. See “Fuel” in the Index. Selecting the Right Schedule First you’ll need to decide which of the two schedules is right for your vehicle. Here’s how to decide which schedule to follow:


Part A: Scheduled Maintenance Services Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You may even need more frequent checks and replacements than you’ll find in the schedules in this section. So please read this section and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your Chevrolet dealer. This part tells you the maintenance services you should have done and when you should schedule them. If you go to your dealer for your service needs, you’ll know that GM-trained and supported service people will perform the work using genuine GM parts.


7-4


Maintenance Schedule I Short Trip/City Definition


Short Trip/City Intervals


Follow the Short TripKity Maintenance Schedule if any one of these conditions is true for your vehicle:


Most trips are less than 5 to 10 miles (8 to 16 km). This is particularly important when outside temperatures are below freezing. Most trips include extensive idling (such as frequent driving in stop-and-go traffic). Most trips are through dusty areas. You frequently tow a trailer or use a carrier on top of your vehicle. If the vehicle is used for delivery service, police, taxi or other commercial application.


One of the reasons you should follow this schedule if you operate your vehicle under any of these conditions is that these conditions cause engine oil to break down soonex


Every 3,000 Miles (5 000 km): Engine Oil and Filter


Change (or 3 months, whichever occurs first). Every 6,000 Miles (10 000 km): Tire Rotation. Every 6,000 Miles (10 000 km) of Trailering: Rear


Axle Fluid Change (Vehicles Towing Trailers).


At the First 6,000 Miles (10 000 km): Rear Axle Fluid


Change (Limited-Slip Differential).


Every 15,000 Miles (25 000 km): Air Cleaner Filter


Inspection, if driving in dusty conditions. Automatic Transmission Service (severe conditions only).


Every 30,000 Miles (50 000 km): Air Cleaner Filter Replacement. Fuel Tank, Cap and Lines Inspection.


Every 50,000 Miles (83 000 km): Automatic Transmission Service (normal conditions).


Every 60,000 Miles (100 000 km): Engine Accessory


Drive Belt Inspection.


7-5


.


Long Tripmighway Intervals Every 7,500 Miles (12 500 km): Engine Oil and Filter Change (or every 12 months, whichever occurs first). Tire Rotation.


At the First 7,500 Miles (12 500 km): Rear Axle Fluid


Change (Limited-Slip Differential).


Every 15,000 Miles (25 000 km): Automatic


Transmission Service (severe conditions only).


Every 30,000 Miles (50 000 km): Air Cleaner Filter Replacement. Fuel Tank, Cap and Lines Inspection.


Every 50,000 Miles (83 000 km): Automatic Transmission Service (normal conditions).


Every 60,000 Miles (100 000 km): Engine Accessory


Drive Belt Inspection.


Every 100,000 Miles (166 000 km): Spark Plug Wire


Inspection. Spark Plug Replacement.


Every 150,000 Miles (240 000 km): Cooling System


Service (or every 60 months, whichever occurs first).


These intervals only summarize maintenance services. Be sure to follow the complete maintenance schedule on the following pages.


Maintenance Schedule I Short


Trip/City Intervals Every 100,000 Miles (166 000 km): Spark Plug Wire


Inspection. Spark Plug Replacement.


Every 150,000 Miles (240 000 km): Cooling System


Service (or every 60 months, whichever occurs first).


These intervals only summarize maintenance services. Be sure to follow the complete maintenance schedule on the following pages.


Follow this maintenance schedule only if none of the conditions from the Short Trip/City Maintenance Schedule is true. Do not use this schedule if the vehicle is used for trailer towing, driven in a dusty area or used off paved roads. Use the Short Trip/City schedule for these conditions. Driving a vehicle with ahlly warmed engine under highway conditions causes engine oil to break down slower.


I Short Trip/City Maintenance Schedule I


The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. The services shown at 150,000 miles (240 000 km) should be performed at the same interval after 150,000 miles (240 000 km). See “Owner Checks and Services” and “Periodic Maintenance Inspections” following.


Footnotes L t The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. + A good time to check your brakes is during tire rotation. See “Brake System Inspection” under “Periodic Maintenance Inspections” in Part C of this schedule.


7-7


I Short Trip/City Maintenance Schedule 3,000 Miles (5 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


An Emission Control Service.


An Emission Control Service. rotation pattern and additional information. (See footnote +.)


6,000 Miles (10 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer or has 9,000 Miles (I5 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


limited-slip differential.


An Emission Control Service.


12,000 Miles (20 000 km)


Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.


0 Change the rear axle gear lubricant if vehicle is used to pull a trailer. 0 Rotate tires. See “Tire Inspection and Rotation’’ in the Index for proper


rotation pattern and additional information. (See footnote +.)


7-8


MILEAGE


DATE


DATE


I Short TripKity Maintenance Schedule I 15,000 Miles (25 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Inspect air cleaner filter if you are driving in dusty conditions. Replace


An Emission Control Service.


filter if necessary. An Emission Control Service. (See footnote?.) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside temperature regularly reaches 90°F


(32°C) or higher.


DATE


1 MILEAGE


ACTUAL


I SERVICEDBY I


- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or delivery service. r f you do not use your vehicle under any of these conditions, change the-fluid andfilter every 50,000 miles (83 000 km).


An Emission Control Service.


18,000 Miles (30 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer.


rotation pattern and additional information. (See footnote +.)


I DATE I MILEAGE


ACTUAL


I SERVICEDBY I


7-9


I Short Trip/City Maintenance Schedule 21,000 Miles (35 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


An Emission Control Service.


24,000 Miles (40 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer. 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper


An Emission Control Service.


rotation pattern and additional information. (See footnote +.)


27,000 Miles (45 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


An Emission Control Service.


30,000 Miles (50 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer.


An Emission Control Service.


7-10


-1 DATE


I SERVICEDBY: I


SERVICED B Y


ACTUAL MILEAGE


DATE


MILEAGE


DATE


ACTUAL MILEAGE


DATE


I Short TripKity Maintenance Schedule I


0 Replace air cleaner filter. 0 Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket


An Emission Control Service.


for any damage. Replace parts as needed. An Emission Control Service. (See footnote?.)


0 Change automatic transmission fluid and filter if the vehicle is mainly driven


under one or more of these conditions: - In heavy city traffic where the outside temperature regularly reaches 90°F


(32°C) or higher.


- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or delivery service. I f you do not use your vehicle under any of these conditions, change the fluid and filter every 50,000 miles (83 000 km). rotation pattern and additional information. (See footnote +.)


0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper


33,000 Miles (55 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


An Emission Control Service.


MILEAGE


7-11


1 Short TripKity Maintenance Schedule I 36,000 Miles (60 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer. 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper


An Emission Control Service,


rotation pattern and additional information. (See footnote +.)


39,000 Miles (65 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


An Emission Control Service.


An Emission Control Service.


42,000 Miles (70 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and Rotation” in the Index for proper 0 Change the rear axle gear lubricant if vehicle is used to pull a trailer. 45,000 Miles (75 000 km) 0 Change engine oil and filter (or every 3 months, whichever occurs first).


rotation pattern and additional information. (See footnote +.)


An Emission Control Service.


7-12


DATE


DATE


I MILEAGE


ACTUAL


I DATE


DATE


I SERVICEDBY: I


Short TripKity Maintenance Schedule


Loading...
x