2011 Cadillac CTS Owners Manual

Black plate (17,1)

Instruments and Controls

5-17

The front passenger safety belt warning light and chime may turn on if an object such as a briefcase, handbag, grocery bag, laptop, or other electronic device is put on the seat . To turn off the warning light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑30.

If the driver safety belt is already buckled, neither the light nor the chime comes on. Passenger Safety Belt Reminder Light

Several seconds after the engine is started, a chime sounds for a number of seconds to remind the front passenger to buckle their safety belt. The passenger safety belt light comes on and stays on for several seconds, flashes for several more seconds, and then comes on solid for several more. This cycle repeats if the passenger remains unbuckled and the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.

The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out.

{ WARNING

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (18,1)

5-18

Instruments and Controls

several seconds as a system check. If the vehicle has remote start, and it is being used to start the vehicle from a distance, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the outboard front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the outboard front passenger frontal airbag.

If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.

{ WARNING

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑17 for more information, including important safety information.

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑37 for important safety information. The instrument panel has a passenger airbag status indicator.

United States

Canada and Mexico

When the vehicle is started, the passenger airbag status indicator will light the words ON and OFF, or the symbols for on and off, for

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (19,1)

Instruments and Controls

5-19

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery.

When this light comes on, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages on page 5‑31. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.

This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. If the Malfunction Indicator Lamp comes on and stays on while the engine is running, this indicates that there is an OBD II problem and service is required.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (20,1)

5-20

Instruments and Controls

Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to

costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emissions system malfunction: . Make sure the fuel cap is

fully installed. See Filling the Tank on page 9‑50. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (21,1)

Instruments and Controls

5-21

If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).

. Make sure the electrical

system is not wet. The system could be wet if the vehicle was driven through a deep puddle of water. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. . Make sure to fuel the vehicle

with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑48.

The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off. The critical emission control systems have not been completely diagnosed by the system. This can happen if the battery has recently been replaced or if the battery has run down.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (22,1)

5-22

Instruments and Controls

The diagnostic system evaluates critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

This light should come on briefly when the ignition is placed in ON/RUN. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light flashes or stays on if the parking brake is not fully released. If the light stays on after the parking brake is fully released, there is a base brake problem.

{ CAUTION

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

For vehicles with the Electric Park Brake (EPB), this red brake warning light comes on when the park brake is applied. If the light continues flashing after the park brake is released, or while driving, there is a problem with the Electric Parking Brake system. If the light does not come on, or remains flashing, see your dealer.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (23,1)

For vehicles with the Electric Park Brake (EPB), this park brake status light should come on briefly when ignition is placed in ON/RUN. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. If this park brake light comes on, there is a problem with a system on the vehicle that is causing the park brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer See Brake Assist (Except CTS-V) on page 9‑37 for more information.

Instruments and Controls

5-23

Antilock Brake System (ABS) Warning Light

For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady. If this happens, start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has

brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑22. For vehicles with a Driver Information Center (DIC), see Driver Information Center (DIC) on page 5‑27 for all brake related DIC messages.

Up-Shift Light

The vehicle may have an up-shift light. It indicates when to shift to the next higher gear for best fuel economy. See Manual Transmission on page 9‑31 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (24,1)

5-24

Instruments and Controls

For the CTS-V, the tracer lights function as a performance up-shift light. The tracers flash to indicate when to shift to the next higher gear to avoid the engine speed limit. See Automatic Transmission on page 9‑26 or Manual Transmission on page 9‑31 for more information.

Traction Control System (TCS)/StabiliTrak® Light

If the light comes on or stays on while driving, there may be a problem with the TCS/StabiliTrak and the vehicle may need service. When this warning light is on, the system does not limit wheel spin. Adjust driving accordingly. See Traction Control System (TCS) on page 9‑38 and StabiliTrak® System on page 9‑39 for more information.

Engine Coolant Temperature Warning Light

If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off. If the light comes on and stays on while driving, the vehicle may have a problem with the cooling system. Stop the vehicle and turn off the engine to avoid damage to the engine. A warning chime sounds when this light is on. See Engine Overheating on page 10‑24 for more information.

Tire Pressure Light

The Traction Control System (TCS)/ StabiliTrak warning light should come on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then goes off.

The engine coolant temperature warning light comes on briefly when the engine is started.

For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (25,1)

Instruments and Controls

5-25

Engine Oil Pressure Light

{ WARNING

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule for changing engine oil.

The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.

When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message can accompany the light. See Tire Messages on page 5‑44 for more information. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑72 for more information.

When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor Operation on page 10‑75 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (26,1)

5-26

Instruments and Controls

Security Light

See Headlamp High/Low-Beam Changer on page 6‑2 for more information.

Front Fog Lamp Light

Lamps On Reminder

This light comes on whenever the parking lamps are on. See Exterior Lamps Off Reminder on page 6‑2 for more information.

The front fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑5 for more information.

This light flashes when the security system is activated. For more information, see Vehicle Security on page 2‑25.

High-Beam On Light

The high-beam on light comes on when the high-beam headlamps are in use.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (27,1)

Instruments and Controls

5-27

Cruise Control Light

Information Displays

This light comes on whenever the cruise control is active. The light goes out when the cruise control is turned off. See Cruise Control on page 9‑41 for more information.

Driver Information Center (DIC) The Driver Information Center (DIC) provides status of many vehicle systems. The DIC displays warning/ status messages. The DIC display is at the bottom of the instrument panel cluster. The DIC buttons are on the instrument panel next to the steering wheel. The DIC comes on when the ignition is on. After a short delay, the DIC displays the information that was last displayed before the engine was turned off. The top line of the DIC display shows the DIC information. The bottom line shows the compass. The compass displays in the trip/fuel menus and in some vehicle information menus.

If a problem is detected, a warning message appears on the display. All messages should be taken seriously and clearing the message does not correct the problem. DIC Operation and Displays

Press the DIC buttons to access the different displays. 3 (Trip/Fuel): Press to scroll through the trip and fuel displays. See “Trip/Fuel Display Menu Items” following for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (28,1)

5-28

Instruments and Controls

T (Vehicle Information): Press to scroll through the vehicle information displays. See “Vehicle Information Display Menu Items” following for more information. U (Customization): Press to scroll through each of the customization features. See Vehicle Personalization on page 5‑46 for more information. V (Set/Reset): Press to reset certain DIC features and to acknowledge and clear DIC warning messages. y z (Menu Up/Down): Press to scroll up and down the menu items. Trip/Fuel Display Menu Items 3 (Trip/Fuel): Press to display the following menu items:

Odometer Displays the distance the vehicle has been driven in either miles (mi) or kilometers (km).

Trip A or Trip B Displays the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time. Reset each trip odometer to zero by pressing and holding the set/reset button when Trip A or Trip B is displayed.

Fuel Range Displays the approximate remaining kilometers (km) or miles (mi) you can drive without refilling the fuel tank. This estimate is based on the current driving conditions and changes if the driving conditions change. For example, freeway driving may produce better fuel economy than city driving with frequent stops, so the range would adjust for that. Once the range drops below about 30 miles (48 km) remaining, the display shows Low Range.

If the fuel is low, the Fuel Level Low message displays. See “Fuel Level Low” under Fuel System Messages on page 5‑36 for more information.

AVG (Average) Economy Displays the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). The calculation is based on the number of L/100 km (mpg) recorded since the last time this display was reset. Press the set/reset button to reset to zero.

Timer Can be used to measure time. For example, timing how long it takes to travel from one point to another. To access the timer, press the trip/fuel button until Timer 00:00:00 displays. To turn on the timer, press the set/reset button.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (29,1)

Instruments and Controls

5-29

To turn off the timer, press the set/reset button again. The timer displays the end timing value. To reset the timer to zero, press and hold the set/reset button.

Inst (Instantaneous) Economy Displays the current fuel economy in either liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number changes frequently as driving conditions change. It cannot be reset.

AVG (Average) Speed Displays the average speed of the vehicle in either kilometers per hour (km/h) or miles per hour (mph). This calculation is based on the various vehicle speeds recorded since the last reset of this display. Press the set/reset button to reset to zero.

Speedometer Displays a digital speedometer in the DIC. The speed displays in either miles per hour (mph) or kilometers per hour (km/h). To change the units from English to metric, see “Units” later in this section.

Blank Display This display shows no information. Vehicle Information Display Menu Items T (Vehicle Information): Press to display the following menu items:

Oil Life Remaining If the vehicle has this display, it shows the estimated oil life remaining. If you see 99% Oil Life Remaining on the display, that means that 99% of the current oil life remains.

When the oil life is depleted, the Change Engine Oil Soon message displays. Change the oil as soon as possible. Additional maintenance is also recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 11‑2 and Engine Oil on page 10‑10. The Oil Life must be reset after each oil change. Avoid accidental resetting of the Oil Life system. It cannot be reset accurately until the next oil change. To reset the engine oil life system, See Engine Oil Life System on page 10‑14. The system is reset when 100% displays.

Units Select to display English or Metric units of measure. Press the set/reset button to select when units is displayed.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (30,1)

5-30

Instruments and Controls

Parking Assist If the vehicle has the Ultrasonic Rear Parking Assist (URPA) system, this display allows the system to be turned on or off. Once in this display, press the set/reset button to select between On or Off. The URPA system automatically turns back on after each vehicle start. When the URPA system is turned off and the vehicle is shifted out of P (Park), the DIC displays the Parking Assist Off message as a reminder that the system has been turned off. See Object Detection System Messages on page 5‑40
and Ultrasonic Parking Assist on page 9‑43 for more information.

Tire Pressure Tire pressure is displayed in the DIC for each tire in either kilopascals (kPa) or pounds per square inch (psi). Press the vehicle information button until the DIC displays Front Tire kPa (PSI) Left ## Right ##. Press the vehicle

information button again until the DIC displays Rear Tire kPa (PSI) Left ## Right ##. If a low tire pressure condition is detected by the system while driving, a message advises to add air to a specific tire displays. See Tire Pressure on page 10‑72 and Tire Messages on page 5‑44 for more information.

Battery Voltage This display shows the current battery voltage. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage may fluctuate when viewing this information on the DIC. This is normal. If there is a problem with the battery charging system, the charging system light illuminates and/or the DIC displays a message. See Charging System Light on page 5‑19, Battery Voltage and Charging Messages on page 5‑31
and Battery Load Management on page 6‑6 for more information.

Calibrate Compass The vehicle may have this feature. The compass can be manually calibrated. To calibrate the compass through the DIC, see “DIC Compass” later in this section.

Change Compass Zone The vehicle may have this feature. To change the compass zone through the DIC, see “DIC Compass” later in this section.

Trans (Transmission) Temp (Temperature) (CTS-V Only) This display shows the transmission fluid temperature in either degrees Fahrenheit (°F) or degrees Celsius (°C).

Oil Pressure (CTS-V Only) This display shows the oil pressure in either pounds per square inch (psi) or kilopascals (kPa).

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (31,1)

Lateral Acceleration (CTS-V Only) Lateral Acceleration measures the force of a turn or corner. For example, when turning right, it forces to the left. This gauge displays the “g” force from 0.0 g to 2.0 g.

Blank Display This display shows no information. DIC Compass The vehicle may have a compass in the Driver Information Center (DIC). See Compass on page 5‑7 for information.

Instruments and Controls

5-31

Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action may be needed to correct a condition. Multiple messages may appear one after another. The messages that do not require immediate action can be acknowledged and cleared by pressing V (Set/Reset).

The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the message does not correct the problem. The following are the possible messages and some information about them.

Battery Voltage and Charging Messages

BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping below expected levels. The battery saver system starts reducing certain features of the vehicle that may be noticeable. At the point that the features are disabled, this message is displayed. It means that the vehicle is trying to save the charge in the battery. Turn off all unnecessary accessories to allow the battery to recharge. The normal battery voltage range is 11.5 to 15.5 volts. You can monitor battery voltage on the DIC by pressing the vehicle information button until Battery Voltage is displayed.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (32,1)

5-32

Instruments and Controls

BATTERY VOLTS LOW This message displays when the electrical system is charging less than 10 volts or the battery has been drained. If this message appears immediately after starting the engine, it is possible that the generator can still recharge the battery. The battery should recharge while driving, but may take a few hours to do so. Consider using an auxiliary charger to boost the battery after returning home or to a final destination. Make sure you follow the manufacturer's instructions. If this message appears while driving or after starting the vehicle and stays on, have it checked immediately to determine the cause of this problem. To help the generator recharge the battery quickly, reduce the load on the electrical system by turning off the accessories.

The normal battery voltage range is 11.5 to 15.5 volts. Monitor battery voltage on the DIC by pressing the vehicle information button until Battery Voltage is displayed. SERVICE BATTERY CHARGING SYSTEM This message displays when there is a problem with the generator and battery charging systems. Driving with this problem could drain the battery. Turn off all unnecessary accessories. Stop and turn off the vehicle as soon as it is safe to do so. Have the electrical system checked by your dealer. Under certain conditions, the charging system light may also turn on in the instrument panel cluster. See Charging System Light on page 5‑19 for more information.

Brake System Messages

PARK BRAKE RELEASED For vehicles with the Electric Parking Brake, this message displays when the parking brake has been released from the set position. See the Electric Parking Brake information under Parking Brake (Manual) on page 9‑34
or Parking Brake (Electric) on page 9‑35 for more information. PARK BRAKE SET For vehicles with the Electric Parking Brake, this message displays when the parking brake has been applied to the set position. See the Electric Parking Brake information under Parking Brake (Manual) on page 9‑34 or Parking Brake (Electric) on page 9‑35 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (33,1)

Instruments and Controls

5-33

SERVICE BRAKE ASSIST This message displays if there is a problem with the brake system. The brake system warning light and the antilock brake system (ABS) warning light may also display on the instrument panel cluster. See Brake System Warning Light on page 5‑22 and Antilock Brake System (ABS) Warning Light on page 5‑23 for more information. Stop as soon as possible and turn off the vehicle. Restart the vehicle and check for the message on the DIC display. If the message displays immediately or again after you begin driving, the brake system needs service. See your dealer as soon as possible. See Antilock Brake System (ABS) on page 9‑33 for more information.

SERVICE BRAKE SYSTEM This message displays, while the ignition is on, when the brake fluid level is low. The brake system warning light on the instrument panel cluster also comes on. See Brake System Warning Light on page 5‑22 for more information. This message may also be displayed for other brake system problems. Have the brake system serviced by your dealer as soon as possible. SERVICE PARK BRAKE For vehicles with the Electric Parking Brake, this message displays if a problem is detected with the electric parking brake system. See your dealer for service.

PRESS BRAKE TO START ENGINE (AUTOMATIC TRANSMISSION ONLY) If the vehicle has the keyless access system, this message displays if you try to start the engine without having the brake pressed. The brake needs to be pressed when starting the engine. See Ignition Positions (Key Access) on page 9‑17 or Ignition Positions (Keyless Access) on page 9‑18 for more information. RELEASE PARK BRAKE SWITCH For vehicles with the Electric Parking Brake, this message displays if the Park Brake switch is pulled while the vehicle is moving. See the Electric Parking Brake information under Parking Brake (Manual) on page 9‑34 or Parking Brake (Electric) on page 9‑35 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (34,1)

5-34

Instruments and Controls

STEP ON BRAKE TO RELEASE PARK BRAKE For vehicles with the Electric Parking Brake, this message displays if you try to release the park brake system without first pressing the brake pedal. See the Electric Parking Brake information under Parking Brake (Manual) on page 9‑34 or Parking Brake (Electric) on page 9‑35 for more information.

Compass Messages

CALIBRATING DRIVE IN CIRCLES This message displays when calibrating the compass. Drive the vehicle in circles at less than 5 mph (8 km/h) to complete the calibration. See Compass on page 5‑7 for more information.

CALIBRATION COMPLETE This message displays when the compass calibration is complete. See Compass on page 5‑7 for more information.

Cruise Control Messages

CRUISE SET TO XXX MPH (KM/H) This message displays whenever the cruise control is set. See Cruise Control on page 9‑41 for more information.

Door Ajar Messages

DRIVER DOOR OPEN This message displays when the driver door is not closed completely. Close the door completely. HOOD OPEN This message displays when the hood is not closed completely. Make sure that the hood is closed completely.

LEFT REAR DOOR OPEN This message displays when the driver side rear door is not closed completely. Make sure that the door is closed completely. PASSENGER DOOR OPEN This message displays when the passenger side front door is not closed completely. Make sure that the door is closed completely. REAR ACCESS OPEN (Wagon) This message displays when the liftgate is not closed completely. Make sure that the liftgate is closed completely. RIGHT REAR DOOR OPEN This message displays when the passenger side rear door is not closed completely. Make sure that the door is closed completely.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (35,1)

Instruments and Controls

5-35

TRUNK OPEN (Sedan and Coupe) This message displays when the trunk is not closed completely. Make sure that the trunk is closed completely.

Engine Cooling System Messages

ENGINE HOT A/C (AIR CONDITIONING) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. See Engine Coolant Temperature Gauge on page 5‑16. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. You can continue to drive the vehicle.

If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. ENGINE OVERHEATED IDLE ENGINE Notice: If you drive the vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 10‑24 for more information. This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. If the message does not clear in a few minutes or if the overheat light stays on, shut the vehicle off and have it serviced before driving again. See Engine Coolant Temperature Warning Light on page 5‑24.

See Overheated Engine Protection Operating Mode on page 10‑25 for information on driving to a safe place in an emergency.

Engine Oil Messages

CHANGE ENGINE OIL SOON When this message displays, it means that service is required for the vehicle. See your dealer. See Scheduled Maintenance on page 11‑2 and Engine Oil on page 10‑10 for more information. When you reset the Change Engine Oil Soon message by clearing it from the display, you still must reset the engine oil life system separately. For more information on resetting the engine oil life system, see Engine Oil Life System on page 10‑14.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (36,1)

5-36

Instruments and Controls

ENGINE OIL LOW ADD OIL If the vehicle has an oil level sensor, this message displays if the oil level in the vehicle is low. Check the oil level and correct it as necessary. You may need to let the vehicle cool or warm up and cycle the ignition to be sure this message clears. This message clears itself after 10 seconds, until the next ignition cycle. See Engine Oil on page 10‑10 for additional information. OIL PRESSURE LOW STOP ENGINE Notice: If you drive the vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil

pressure is corrected. See Engine Oil on page 10‑10 for more information. This message displays when the vehicle's engine oil pressure is low. The oil pressure light may also appear on the instrument panel cluster. See Engine Oil Pressure Light on page 5‑25. See Engine Oil on page 10‑10 for more information. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer as soon as possible when this message is displayed.

Engine Power Messages

ENGINE POWER IS REDUCED This message displays when the engine power is being reduced to protect the engine from damage. There could be several malfunctions that might cause this message. Reduced engine power can affect the vehicle's ability to accelerate.

If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refill the fuel tank as soon as possible. A chime may sound when this message displays. See Filling the Tank on page 9‑50.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (37,1)

Instruments and Controls

5-37

TIGHTEN GAS CAP This message displays when the fuel cap has not been fully tightened. Recheck the fuel cap to ensure that it is on and tightened properly.

Key and Lock Messages

ACCESSORY MODE ACTIVE If the vehicle has the keyless access system, this message displays when the accessory mode is active. See Ignition Positions (Key Access) on page 9‑17 or Ignition Positions (Keyless Access) on page 9‑18 for more information. ELECTRONIC KEY ALREADY KNOWN If the vehicle has the keyless access system, this message displays if you try to match a transmitter that has already been learned. See the Keyless Access

information for Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 for more information. ELECTRONIC KEY NOT DETECTED If the vehicle has the keyless access system, this message displays if the vehicle does not detect the presence of a transmitter when you have attempted to start the vehicle or a vehicle door has just closed. The following conditions may cause this message to appear: . Driver-added equipment plugged

into the accessory power outlet on the center console is causing interference. Examples of these devices are cell phones and cell phone chargers, two-way radios, power inverters, or similar items.

Try moving the keyless access transmitter away from these devices when starting the vehicle. In addition, PDA devices and remote garage and gate openers may also generate Electromagnetic Interference (EMI) that may interfere with the keyless access transmitter. Do not carry the keyless access transmitter in the same pocket or bag as these devices. The vehicle is experiencing Electromagnetic Interference (EMI). Some locations, such as airports, automatic toll booths, and some gas stations have EMI fields which may interfere with the keyless access transmitter.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (38,1)

5-38

Instruments and Controls

ELECTRONIC KEY NOT DETECTED RESTART ALLOWED If the vehicle has the keyless access system, this message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off. The vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed. If you have the keyless access transmitter with you, get out of the vehicle and lock the doors. If you do not have the keyless access transmitter with you, you will be able to start the vehicle again within five minutes, or until the vehicle's content theft deterrent system is armed. See Starting the Engine on page 9‑19 for more information.

LEARN DELAY ACTIVE WAIT XX MIN (MINUTES) If the vehicle has the keyless access system, this message displays when matching new transmitters to the vehicle. See the Keyless Access information for Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 for more information. MAXIMUM # ELECTRONIC KEYS LEARNED If the vehicle has the keyless access system, this message displays when the maximum number of transmitters have been learned. See the Keyless Access information for Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 for more information.

If moving the transmitter to different locations within the vehicle does not help, place the transmitter in the center console transmitter pocket with the buttons facing the front of the vehicle and then start the vehicle. The vehicle's battery voltage is low. The battery voltage must be above 10 volts for the keyless access transmitter to be detected properly.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (39,1)

Instruments and Controls

5-39

PRESS START CONTROL TO LEARN KEYS If the vehicle has the keyless access system, this message displays when matching new transmitters to the vehicle. See the Keyless Access information for Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 for more information. READY TO LEARN ELECTRONIC KEY # X If the vehicle has the keyless access system, this message displays while matching new transmitters to the vehicle. See the Keyless Access information for Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 for more information.

REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) or keyless access transmitter needs to be replaced. To replace the battery, see “Battery Replacement” under Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7. ROTATE CONTROL TO OFF POSITION If the vehicle has the keyless access system, this message displays when the ignition is in ACC/ACCESSORY and the shift lever has just been moved to P (Park). The message displays as a reminder to turn the ignition off. To avoid draining the battery, make sure the ignition is turned off before leaving the vehicle.

SERVICE KEYLESS START SYSTEM If the vehicle has the keyless access system, this message displays when there is a problem with this feature. See your dealer.

Lamp Messages

AFL (ADAPTIVE FORWARD LIGHTING) LAMPS NEED SERVICE This message displays when the Adaptive Forward Lighting (AFL) system is disabled and needs service. See your dealer. See Adaptive Forward Lighting (AFL) on page 6‑4 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (40,1)

5-40

Instruments and Controls

AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. TURN SIGNAL ON This message displays as a reminder to turn off the turn signal if you drive the vehicle for more than about 1.6 km (1 mile) with a turn signal on. A multiple chime sounds when this message displays.

Object Detection System Messages

Ride Control System Messages

PARKING ASSIST OFF If the vehicle has the Ultrasonic Rear Parking Assist (URPA) system, after the vehicle has been started, this message displays to remind the driver that the URPA system has been turned off. Press the set/reset button to acknowledge this message and clear it from the DIC display. To turn the URPA system back on, see “Parking Assist” under Driver Information Center (DIC) on page 5‑27. See Ultrasonic Parking Assist on page 9‑43 for more information. SERVICE PARKING ASSIST If the vehicle has the Ultrasonic Rear Parking Assist (URPA) system, this message displays if there is a problem with the URPA system. See Ultrasonic Parking Assist on page 9‑43 for more information. See your dealer for service.

ALL WHEEL DRIVE OFF If the vehicle has the All-Wheel Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in 2WD. This could be caused by: Loss of wheel or vehicle speed

. AWD system overheat . Certain vehicle electrical

conditions

This message turns off when the above conditions are no longer present and by resetting the warning message. To reset the warning message, turn the ignition off and then back on again after 30 seconds. If the message stays on, see your dealer right away. See All-Wheel Drive on page 9‑33 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (41,1)

SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel Drive (AWD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . An AWD system oil overheat . Worn out or overheated clutch

plates

. Various electrical issues If this message appears, stop as soon as possible and turn off the ignition for 30 seconds. Restart the vehicle and check for the message on the DIC display. If the message is still displayed or appears again when you begin driving, the system needs service. See your dealer right away. SERVICE POWER STEERING This message displays if a problem is detected with the speed variable assist steering system. When this message is displayed, you may

Instruments and Controls

5-41

notice that the effort required to steer the vehicle increases or feels heavier, but you will still be able to steer the vehicle. See Steering on page 9‑4. SERVICE STABILITRAK This message displays if there has been a problem detected with the StabiliTrak® system. The TCS/StabiliTrak warning light on the instrument panel cluster also comes on. If this message comes on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off then back on. If this message still stays on or comes back on again while you are driving, the vehicle needs service. Have the StabiliTrak system inspected by your dealer as soon as possible. See StabiliTrak® System on page 9‑39 for more information.

SERVICE SUSPENSION SYSTEM This message displays when there is a problem with the Magnetic Ride Control system. See Magnetic Ride Control on page 9‑40 for more information. Have the vehicle serviced by your dealer. SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). The TCS/StabiliTrak warning light on the instrument panel cluster also comes on. When this message displays, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control System (TCS) on page 9‑38
for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (42,1)

5-42

Instruments and Controls

STABILITRAK COMPETITIVE MODE This message displays when the Competitive Driving mode is selected. When in this mode, the Traction Control System (TCS) will not be operating and the TCS/ StabiliTrak warning light will turn on. Adjust your driving accordingly. See “Competitive Driving Mode” under Traction Control System (TCS) on page 9‑38 for more information. STABILITRAK NOT READY This message may display after first driving the vehicle and exceeding 30 km/h (19 mph) for 30 seconds. The TCS/StabiliTrak warning light on the instrument panel cluster also comes on. The StabiliTrak system is not functional until the message has turned off. See StabiliTrak® System on page 9‑39 for more information.

STABILITRAK OFF This message displays when you turn off StabiliTrak, or when the stability control has been automatically disabled. The TCS/StabiliTrak warning light on the instrument panel cluster also comes on. To realize the full benefits of the stability enhancement system, you should normally leave StabiliTrak on. To turn the StabiliTrak system on or off, see StabiliTrak® System on page 9‑39. There are several conditions that can cause this message to appear. . One condition is overheating,

which could occur if StabiliTrak activates continuously for an extended period of time. The message also displays if the brake system warning light is on. See Brake System Warning Light on page 5‑22.

The message could display if the stability system takes longer than usual to complete its diagnostic checks due to driving conditions. The message displays if an engine or vehicle related problem has been detected and the vehicle needs service. See your dealer.

The message turns off as soon as the conditions that caused the message to be displayed are no longer present. SUSPENSION MODE SPORT (CTS-V ONLY) This message will be displayed when sport mode is selected using the Magnetic Ride Control button in the center of the instrument panel. See Magnetic Ride Control on page 9‑40 for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (43,1)

Instruments and Controls

5-43

SUSPENSION MODE TOUR (CTS-V ONLY) This message will be displayed when touring mode is selected using the Magnetic Ride Control button in the center of the instrument panel. See Magnetic Ride Control on page 9‑40 for more information.

Airbag System Messages

SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have the vehicle serviced by your dealer immediately. See Airbag Readiness Light on page 5‑17 for more information.

Anti-Theft Alarm System Messages

SERVICE THEFT DETERRENT SYSTEM This message displays when there is a problem with the theft-deterrent system programmed in the key. A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle. The vehicle usually restarts; however, you may want to take the vehicle to your dealer before turning off the engine. See Immobilizer Operation (Key Access) on page 2‑26 or Immobilizer Operation (Keyless Access) on page 2‑27 for more information.

START ABORTED BY THEFT DETERRENT This message displays if there is a communication problem between the keyless access system and the vehicle. The vehicle cannot be started when this message displays. See your dealer for service. THEFT ATTEMPTED This message displays if the theft-deterrent system has detected a break-in attempt while you were away from the vehicle. See Anti-Theft Alarm System on page 2‑25 for more information.

Service Vehicle Messages

SERVICE A/C SYSTEM This message displays when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (44,1)

5-44

Instruments and Controls

SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer as soon as possible.

Tire Messages

SERVICE TIRE MONITOR SYSTEM This message displays if a part on the Tire Pressure Monitor System (TPMS) is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 5‑24. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 10‑75 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer.

TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is re-learning the tire positions on the vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Rotation on page 10‑79, Tire Pressure Monitor System on page 10‑74, and Tire Pressure on page 10‑72 for more information. TIRE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle’s tires is low. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑24.

If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire Loading Information label. See Tires on page 10‑64, Vehicle Load Limits on page 9‑11, and Tire Pressure on page 10‑72. If the vehicle does not have a spare tire, the message will display “Use Inflator Kit in Trunk”. Use the inflator kit to inflate the tires to the correct pressure. See Tire Sealant and Compressor Kit on page 10‑89 for more information. More than one tire pressure message can be received at a time. To read the other messages, press the set/reset button. The DIC display also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑27.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (45,1)

Instruments and Controls

5-45

Transmission Messages

DIFFERENTIAL HOT, REDUCE SPEED (CTS-V ONLY) This message displays and a chime sounds if the differential fluid temperature exceeds 150°C (300°F). Driving aggressively or at high speeds can cause the differential fluid temperature to be higher than normal. If this message appears, you may continue to drive at a slower speed. If you have been operating the vehicle under normal driving conditions, the vehicle may need service. See your dealer for an inspection. To acknowledge the message, press V. The message reappears and a chime sounds every two minutes until this condition changes. If you do not clear the message, it will remain on until the condition changes.

SERVICE TRANSMISSION This message displays when there is a problem with the vehicle's transmission. Have the vehicle serviced by your dealer. SHIFT TO PARK (AUTOMATIC TRANSMISSION ONLY) If the vehicle has the keyless access system, this message displays if the vehicle is not in P (Park) while the engine is being turned off. The vehicle will be in ACC/ACCESSORY. Once the shift lever is moved to P (Park), the ignition needs to be turned off. If the ignition is not turned off, the vehicle will remain in ACC/ACCESSORY. To avoid draining the battery, turn the ignition to off before leaving the vehicle.

SPORT MODE This message displays when the vehicle is in sport mode. The transmission gear position will also be displayed when DSC is in use. See “Driver Shift Control (DSC)” under Automatic Transmission on page 9‑26 for more information. TRANSMISSION HOT IDLE ENGINE This message displays when the transmission fluid in the vehicle is too hot. Stop the vehicle and allow it to idle until the transmission cools down or until this message is removed.

Vehicle Speed Messages

ICE POSSIBLE DRIVE WITH CARE This message displays when the outside temperature is cold enough to create icy road conditions. Adjust your driving accordingly.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (46,1)

5-46

Instruments and Controls

SPEED LIMITED TO XXX KM/H (MPH) This message displays when the vehicle speed is limited to 128 km/h (80 mph) because the vehicle detects a problem in the speed variable assist steering, magnetic ride control, or automatic leveling control systems. Have the vehicle serviced by your dealer.

Washer Fluid Messages

WASHER FLUID LOW ADD FLUID This message displays when the vehicle is low on windshield washer fluid. Refill the windshield washer fluid reservoir as soon as possible. See Washer Fluid on page 10‑26 for more information.

Vehicle Personalization Vehicle customization allows certain features to be programmed for one preferred setting. Only the customization options available will be displayed on the DIC. The default settings were preset when the vehicle left the factory, but may have been changed. The customization preferences are automatically recalled. To change customization preferences, use the following procedure. Entering the Feature Settings Menu 1. Turn the ignition on.

To avoid excessive drain on the battery, it is recommended that the headlamps are turned off.

2. Press the customization

button to enter the feature settings menu.

Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle:

Display In English This feature will only display if a language other than English has been set. This feature allows for changing the language of the DIC messages back to English. Press the customization button until the Press V To Display In English screen appears on the DIC display. Press the set/reset button once to select English as the language in which all DIC messages will appear.

Display Language This feature allows you to select the language in which the DIC messages will appear.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (47,1)

Instruments and Controls

5-47

Press the customization button until the Display Language screen appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: English (default): All messages will appear in English. Deutsch: All messages will appear in German. Italiano: All messages will appear in Italian. Francais: All messages will appear in French. Espanol: All messages will appear in Spanish. Portugese: All messages will appear in Portugese. Arabic: All messages will appear in Arabic. Chinese: All messages will appear in Chinese. Japanese: All messages will appear in Japanese.

No Change: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.

Auto Door Lock This feature allows you to select when the vehicle's doors will automatically lock. See Automatic Door Locks on page 2‑17 for more information. Press the customization button until Auto Door Lock appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: Shift Out Of Park (default on Automatic Transmission) (Automatic Transmission Only): The vehicle's doors automatically lock when the doors are closed and the vehicle is shifted out of P (Park).

At Vehicle Speed (default on Manual Transmission): The vehicle's doors automatically lock when the vehicle speed is above 5 mph (8 km/h) for three seconds. No Change: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.

Auto Door Unlock This feature allows you to select whether or not the door(s) will automatically unlock. It also allows you to select which doors and when they will automatically unlock. See Automatic Door Locks on page 2‑17
for more information.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (48,1)

5-48

Instruments and Controls

Press the customization button until Auto Door Unlock appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: Off: None of the doors will automatically unlock. Driver Only At Off: Only the driver door will unlock when the ignition is turned off. All At Off (default on Manual Transmission): All of the doors will unlock when the ignition is turned off. All In Park (default on Automatic Transmission) (Automatic Transmission Only): All of the doors will unlock when the vehicle is shifted into P (Park). No Change: No change will be made to this feature. The current setting will remain.

To select a setting, press the set/reset button while the desired setting is displayed on the DIC.

Remote Door Lock Feedback This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) or keyless access transmitter, or when the vehicle is automatically locked using the Keyless Locking feature. You will not receive feedback when locking the vehicle with the transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 or “Keyless Locking” later in this section for more information.

Press the customization button until Remote Door Lock appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: Off: There will be no feedback when you press the lock button on the transmitter. Lights Only: The exterior lamps will flash when you press the lock button on the transmitter. Horn Only: The horn will sound on the second press of the lock button on the transmitter. Horn & Lights (default): The exterior lamps will flash when you press the lock button on the transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. No Change: No change will be made to this feature. The current setting will remain.

Cadillac CTS/CTS-V Owner Manual - 2011

Black plate (49,1)

To select a setting, press the set/reset button while the desired setting is displayed on the DIC.

Remote Door Unlock Feedback This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) or keyless access transmitter, or when the vehicle is automatically unlocked using the Keyless Unlock feature. You will not receive feedback when unlocking the vehicle with the transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation (Key Access) on page 2‑5 or Remote Keyless Entry (RKE) System Operation (Keyless Access) on page 2‑7 or “Keyless Unlock” later in this section for more information.

Instruments and Controls

5-49

Press the customization button until Remote Door Unlock appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: Lights Off: The exterior lamps will not flash when you press the unlock button on the transmitter. Lights On (default): The exterior lamps will flash when you press the unlock button on the transmitter. No Change: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.

Exit Lighting This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF.