Login- Download PDF Manual
-
Carsseatingseven Emergency puncture repair kit The emergency puncture repair kit1 is only intended to work as a temporary repair so that the car can be driven a further 200 km (max.) or to the nearest tyre centre. The seal- ing fluid has the ability to effectively seal tyres which have punctures in the tread. The canister with the sealing fluid should be replaced before the best-before date has expired or after the emergency puncture repair kit has been used. The best-before date is located on the front of the compressor, see illustration on page 161.
1.
Certain variants and markets
Wheels and tyres
Re placement of emergency puncture repair kit, see page 161 for information on replacing the canister. NOTE! The emergency puncture repair kit is only intended for sealing tyres with a punc- ture in the tread. The emergency puncture repair kit has limited abilities to seal tyres which have punctures in the wall of the tyre. Do not seal tyres with the emergency puncture repair kit if they have larger slits, cracks or similar damage. The emergency puncture repair kit with com- pressor and tools are found under the floor in the cargo area. 12 V sockets for the compressor are located by the centre console in the front, by the rear seat and in the cargo area. Choose the elec- trical socket that is nearest the punctured tyre.
WARNING!
The sealing fluid may cause irritation if it comes into direct contact with skin. In the case of contact with skin, wash away the fluid with soap and water.
Taking out the emergency puncture repair kit – Fold the rear edge of the floor mat
forward.
– Lift up the emergency puncture repair kit. 157
Wheels and tyres
Emergency puncture repair
Inflating tyres Set up the warning triangle if a tyre must be inflated in an area close to traffic. – Ensure that the orange switch (2) is in
position 0 and take out the lead (5) and air hose (4) from the side compartment (3).
– Screw the air hose’s valve connection to the bottom of the thread on the tyre’s air valve.
– Connect the lead (5) to one of the car’s
12 V sockets.
– Start the engine. The car must be in a
well-ventilated place.
158
– Start the compressor by flicking the
switch (2) to position I.
– Pump up the tyre to the pressure
specified on the tyre pressure label.
– Turn off the compressor, the switch (2) should be in position 0. Detach the air hose and unplug the lead. Replace the valve’s dust cap.
– Put the lead (5) and air hose (4) into the
side compartment (3).
– Put the puncture repair kit back under the
floor in the cargo area.
– The compressor should not run for more
than ten minutes at a time. Let it cool afterwards as there is a risk of overheating.
– Objects with a volume of up to 50 litres can be pumped up with the compressor.
WARNING!
Inhaling car exhaust fumes can result in danger to life. Never leave the engine running in sealed areas or areas that lack sufficient ventilation.
Emergency puncture repair
Wheels and tyres
Sealing punctured tyres Set up the warning triangle if emergency tyre repairs must be carried out in an area where there is other traffic. – Remove the decal (1) regarding the
highest permitted speed from the emergency puncture repair kit and stick it on the steering wheel where it can be clearly seen by the driver.
– Ensure that the orange switch (2) is in
position 0 and take out the lead (5) and air hose (4) from the side compartment (3).
– Screw the air hose’s valve connection to the bottom of the thread on the tyre’s air valve.
– Connect the lead (5) to one of the car’s
– Start the compressor by flicking the
12 V sockets.
– Release the safety catch (6) and turn the orange-coloured part (7) 90 degrees to the vertical position, until a click is heard.
– Start the engine. The car must be in a
well-ventilated place.
WARNING!
Inhaling car exhaust fumes can result in danger to life. Never leave the engine running in sealed areas or areas that lack sufficient ventilation.
switch (2) to position I. The pressure may increase temporarily up to a maximum of 4 bar while the sealing liquid is being pumped in. After about one minute, the pressure will drop and the pressure gauge show a more correct tyre pressure.
– Pump the tyre to a pressure of between 1.8 bar and 3.5 bar. If the pressure does not reach 1.8 bar after ten minutes of pumping, the compressor should be turned off so it does not overheat.
– Undo the air hose (4) from the air valve
and put the dust cap back on. Unplug the lead (5) from the electrical socket. Fold the orange-coloured part (7) back into its
159
Wheels and tyres
Emergency puncture repair
WARNING!
Never stand next to the tyre when the compressor is running. Be particularly observant of the tyre walls. If cracks, irreg- ularities or other damage appears, turn off the compressor immediately. Under these circumstances your journey should not continue. Contact an authorised tyre centre.
original position and secure the catch (6). Keep the emergency repair kit in a safe place in the car.
– Immediately drive about 3 km, at a
maximum speed of 80 km/h, to allow the sealing fluid to seal the tyre well.
WARNING!
You should not drive faster than 80 km/h after the emergency tyre repair kit has been used. The temporarily sealed tyre must be changed as soon as possible (maximum driving distance: 200 km).
– Check the tyre pressure again: NOTE! Do not raise the orange-coloured part (7) when only the compressor is to be used for inflation.
160
– Connect the air hose (4) to the air valve
on the tyre.
– Connect the lead (5) to the 12 V power
point. Read the pressure on the compressor. If the tyre pressure is below 1.3 bar, the tyre has not been sufficiently well sealed. The journey should not be continued under these circumstances. Contact a tyre centre.
– If the tyre pressure is higher than 1.3 bar,
the tyre should be pumped up to the pressure stated on the tyre pressure label, see page 151 for its location. Release pressure with the reduction valve (8) if the tyre pressure is too high. – Turn off the compressor, the switch (2) should be in position 0. Detach the air hose and unplug the lead. Replace the valve’s dust cap.
– Put the lead (5) and air hose (4) into the
side compartment (3).
– Put the puncture repair kit back under the
floor in the cargo area.
The compressor should not run for more than ten minutes at a time. Let it cool afterwards as there is a risk of overheating. NOTE! The canister with sealant and hose should be replaced after use.
Emergency puncture repair
Wheels and tyres
Changing the sealing fluid canister The canister of sealing fluid should be changed before the best-before date has expired, see date label (1), or after the tyre has been sealed. After use, the canister (6) with holder (8) and air hose (10) should be changed.
IMPORTANT! Read the safety instructions on the bottom of the canister.
WARNING!
Ensure the compressor is not connected to the 12 V socket when the canister is changed.
Before the best-before date has expired – Undo the two screws (2) on the orange-
coloured case (3).
– Remove the speed label (4) and date
label (1), and open the safety catch (5). Loosen the case (3) and take it off.
– Unscrew and remove the canister (6). – Check that the seal (7) on the new canister is not damaged. Screw the canister into place.
– Refit the case (3). Check that the case is
correctly fitted. Screw it on with the screws (2).
– Affix the speed label (4) and new date
label (1) to the tyre repair kit.
Treat the removed canister as hazardous waste. Changing the canister and hose after use – Undo the two screws (2) on the orange-
coloured case (3).
– Remove the speed label (4) and date
label (1), and open the safety catch (5). Loosen the case (3) and take it off.
161
Wheels and tyres
Emergency puncture repair – Push down the button (8) while turning
the canister (6) and the holder (9) clockwise. Remove them. – Pull out the air hose (10). – Wipe off remaining sealing fluid with a rag or scrape it away if it is has already dried.
– Fit a new air hose (10). Check that it is
fitted correctly.
– Check that the seal (7) on the new canister is not damaged. Screw the holder (9) onto the canister (6) and turn it anticlockwise until a click is heard.
– Refit the case (3). Check that the case is
correctly fitted. Screw it on with the screws (2).
– Affix the speed label (4) and new date
label (1) to the tyre repair kit.
The empty canister and air hose can be treated as normal waste.
162
Cleaning Touching up paintwork Rustproofing
Car care 164
166
168163
Car care
Cleaning Washing the car Wash the car as soon as it becomes dirty. Use car shampoo. Dirt and road salt can lead to corrosion. (cid:127) Do not park the car in direct sunshine. Washing a car with hot paintwork can cause permanent paintwork damage. Wash the car in a car wash with waste water separator.
(cid:127) Thoroughly rinse dirt off the underbody of
the car.
(cid:127) Rinse the entire car to remove loose dirt.
When using a pressure washer: Make sure that the nozzle of the pressure washer is not closer than 30 cm to the bodywork. Do not spray directly at the locks.
(cid:127) Wash using a sponge, car shampoo and
(cid:127)
plenty of lukewarm water. If the dirt is difficult to dislodge, wash the car using a cold degreasing agent.
(cid:127) Dry the car using a clean, soft chamois or
a water scraper.
(cid:127) Clean the wiper blades with a lukewarm
soap solution or car shampoo.
164
Removing bird droppings Wash bird droppings off the paintwork as soon as possible. Bird droppings contain chemicals that affect and discolour paintwork very quickly. This discolouration can only be removed by a specialist.
WARNING!
Always test the brakes after washing the car to ensure that moisture and corrosion do not attack the brake pads and reduce braking performance.
Press the brake pedal lightly from time to time if driving for long periods in rain or slush. This heats and dries the brake pads. You should also do this when you begin driving in extremely damp or cold weather. Exterior plastic parts A special cleaning agent, available from Volvo dealers, is recommended for cleaning exterior plastic parts. Never use strong stain removers.
WARNING!
Always have the engine cleaned by a workshop. There is a risk of fire if the engine is hot.
Automatic car washes An automatic car wash is a simple and quick way of washing the car. Bear in mind, however, that an automatic car wash can never replace a proper handwashing – the brushes of a car wash cannot reach everywhere.
IMPORTANT! Washing by hand is gentler to the paintwork than an automatic car wash. The paintwork is also more sensitive when it is new. For this reason, handwashing is recommended during the first few months with a new car.
Cleaning Cleaning the interior Treating spots on fabric upholstery A special cleaning agent, available from Volvo dealers, is recommended for cleaning the fabric upholstery. Other chemicals can impair the fire retardant qualities of the upholstery.
IMPORTANT! Sharp objects and Velcro may damage the fabric upholstery.
Treating spots on leather upholstery A special cleaning agent, available from Volvo dealers, is recommended when cleaning leather upholstery. Treat the leather uphol- stery once or twice a year using Volvo’s leather care kit. Never use strong solvents. Such products may damage fabric, vinyl and leather upholstery. Treating spots on interior plastic parts and surfaces A special cleaning agent, available from Volvo dealers, is recommended for cleaning interior plastic parts and surfaces. Do not scrape or rub spots. Never use strong stain removers. Cleaning seatbelts Use water and a synthetic detergent. A special textile cleaning agent is available from
you Volvo dealer. Make sure the seatbelt is dry before allowing it to retract. Polishing and waxing Polish and wax the car when you feel the paintwork is matte and when you wish to give the paintwork extra protection, such as before winter. The car does not usually need polishing until after one year. It can be waxed earlier. Wash and dry the car thoroughly before you begin polishing and/or waxing. Clean off asphalt and tar stains with white spirit. More stubborn marks can be removed with fine rubbing paste designed for paintwork. Polish first with a polish and then wax with liquid or solid wax. Carefully follow the instructions on the package. Many preparations contain both polish and wax. Do not polish or wax surfaces warmer than 45 °C. Cleaning door mirrors and front door windows with water- repellent coating (option) Never use products such as car wax, degreaser or the like on mirror/ glass surfaces as this could ruin their water- repelling properties.
Car care
Take care when cleaning so as not to damage the glass surface. To avoid damaging glass surfaces when removing ice, only use plastic ice scrapers. There is natural wear of the water-repellent coating. NOTE! Treatment with a special finishing agent available from Volvo dealers is recom- mended in order to maintain the water- repellent properties. This should be used first after three years and then each year.
165
Car care
Touching up paintwork Paintwork Paint is an important part of the car’s rustproofing and should therefore be checked regularly. Repair paintwork damage immediately so that it does not start to rust. The most common types of paintwork damage that you can repair yourself are: (cid:127) minor stone chips and scratches (cid:127) damage to wing edges and door When repairing paintwork, the car should be clean and dry with a temperature above 15 °C. Colour code Make sure you have the right colour. The colour code number is on the data plate in the engine compartment.
166
Variant1
Variant 2
Only China
Removeanypaintresiduewithtape.Maskif necessary. Minor stone chips and scratches Material: (cid:127) Primer in a can (cid:127) Paint in a can or a touch-up pen (cid:127) Brush (cid:127) Masking tape (cid:127)
If the stone chip has not gone down to the bare metal and an unpainted colour coat remains, you can add paint immedi- ately after removing dirt.
Touching up paintwork Do as follows if the stone chip went down to the bare metal: (cid:127) Fasten a piece of masking tape over the damaged surface. Then remove the tape, removing any paint residue (illustration 1). (cid:127) Stir the primer thoroughly and apply using a fine brush or matchstick (illustration 2). (cid:127) When the primer is dry, apply the surface
coat with a brush.
(cid:127) Make sure the paint is well stirred and
apply several thin coats; allowing it to dry between coats.
(cid:127) The procedure is the same for scratches, but masking tape can be used to protect undamaged paintwork (illustration 3).
(cid:127) Wait a day or so and then finish the repair
by polishing. Use a soft rag and apply lapping paste sparingly.
Car care
167
Car care
Rustproofing Rustproofing – check and repair Your car received a thorough and complete rustproofing at the factory. Parts of the body are made of galvanised sheet metal. The underbody is protected by a wear-resistant anti-corrosion compound. Members, cavities and enclosed sections are sprayed with a thin, penetrating rust inhibitor. The car’s rustproofing is maintained by doing the following: (cid:127) Keep the car clean! Hose down the
underbody. When high pressure washing, hold the nozzle at least 30 cm from painted surfaces!
(cid:127) Check and repair the rustproofing
regularly.
The car’s rustproofing does not normally require treatment for approximately 8 years. After that time, it should be treated at three year intervals. If your car requires treatment, consult your Volvo workshop. Repair If you want to repair the rustproofing yourself, make sure the area is clean and dry. Hose down, wash and dry the car thoroughly. Use a rustproofing agent in a spray can or one that is intended for brush application.
168
There are two different types of rustproofing agents: (cid:127) (cid:127)
thin (colourless), for visible areas thick, for areas prone to wear on the underbody
Possible repair areas with these agents: (cid:127) Visible welds and sheet metal joints; thin
fluid
(cid:127) Underbody; thick fluid (cid:127) Door hinges; thin fluid (cid:127) Bonnet hinges and catch - thin fluid. Once you have finished treatment, excess rustproofing can be wiped off with a rag dipped in a recommended cleaning agent. Parts of the engine and suspension strut mountings in the engine compartment are treated at the factory with a wax-based, colourless rustproofing. This withstands normal detergents without dissolving and losing its rustproofing ability. If you wash the engine using aromatic solvents, such as turpentine or white spirit (especially those that do not contain emulsi- fiers), the protective wax should be renewed after washing. Your Volvo dealer handles such waxes.
Volvo service Self-maintenance Bonnet and engine compartment Diesel Oils and fluids Wiper blades Battery Replacing bulbs Fuses
Maintenance and service 170
171
172
173
174
178
179
182
190169
collision. Volvo Car Corporation will not disclose the stored information without consent. However, Volvo Car Corporation may be forced to disclose the information due to national legislation. Volvo Car Corporation and its workshops may also read and use the information.
Maintenance and service
Volvo service Volvo service programme Before the car left the factory, it was thoroughly test driven. It was checked again in accordance with Volvo Car Corporation regulations before it was handed over to you. To keep your Volvo as safe and reliable as possible, follow the Volvo service programme specified in the Service and Warranty Booklet. Have an authorised Volvo workshop carry out service and maintenance work. Volvo workshops have the personnel, special tools and service literature to guarantee the highest quality of service.
IMPORTANT! For the Volvo warranty to apply, check and follow the instructions in the Service and Warranty Booklet.
Special service measures Certain service measures, which affect the car’s electrical system, can only be performed using electronic equipment specially developed for your car. Always contact an authorised Volvo workshop before beginning or performing service work that affects the electrical system.
170
Installing accessories The incorrect connection and installation of accessories can negatively affect the car’s electrical system. Certain accessories only function when the appropriate software has been programmed into the car’s electrical system. Always contact an authorised Volvo workshop before installing accessories which are connected to or affect the electrical system. Recording vehicle data One or more of the computers in your Volvo are capable of recording detailed information. This information is intended for use in research to enhance safety and for diagnosing faults in some of the in-car systems. The data may include details regarding seatbelt use by the driver and passengers, the functions of various vehicle systems and modules, and status information about the engine, throttle, steering, brakes and other systems. This data can also include details of the way the car is driven. This type of information can include, without being limited to, specific details such as vehicle speed, the use of the brake and accelerator pedals and steering wheel position. This latter type of data can be stored for a limited period while the car is being driven and subsequently during a collision or a near-
Self-maintenance Before starting work on the car Battery Check that the battery cables are correctly connected and tightened. Never disconnect the battery when the engine is running (e.g. if replacing the battery). Never use a quick charger to charge the battery. The battery cables must be discon- nected when charging the battery. The battery contains acid that is both corrosive and toxic. Handle the battery in an environmentally-suitable way. Let your Volvo dealer assist you.
WARNING!
High voltage output from the ignition system. The voltage in the ignition system is dangerous. The ignition must therefore always be switched off for work in the engine compartment. Do not touch the spark plugs or ignition coils when the ignition is on or the engine is hot.
Check regularly Check the following at regular intervals, for example, when refuelling: (cid:127) Coolant - The level must be between the
MIN and MAX marks on the expansion tank.
(cid:127) Engine oil - The level must be between
the MIN and MAX marks.
(cid:127) Power steering fluid - The level must be
between the MIN and MAX marks.
(cid:127) Washer fluid - The reservoir should be
well filled. Use washer antifreeze at temperatures around freezing.
(cid:127) Brake and clutch fluid - The level must be
between the MIN and MAX marks.
WARNING!
Bear in mind that the radiator fan may start automatically some time after the engine has been switched off. Always have the engine cleaned by a workshop. There is a risk of fire if the engine is hot.
Maintenance and service
Lifting the car If the car is lifted with a workshop jack; position the jack with the front edge on the subframe. Do not damage the splashguard under the engine. Ensure that the jack is positioned so that the car cannot slide off. Always use axle stands or the like. If you lift the car using a two pillar workshop lift, ensure that the front and rear lift arms are fixed under the lifting points on the door sill. See the illustration.
171
Maintenance and service
Bonnet and engine compartment
10
11
Opening the bonnet – Pull the handle on the far left (or right if
the car is RHD) under the dashboard. You will hear when the lock releases.
– Insert your hand to the right under the
front edge of the bonnet (below the grille).
– Press up the safety catch handle. – Release the handle and open the bonnet.
Engine compartment The appearance of the engine compartment may vary slightly due to engine variant. However, the components listed are in the same positions. 1. Clutch and brake fluid reservoir 2. Relay and fuses 3. Air filter. (The cover has a different
design depending on engine variant.)
10. Chassis data plate 11. Battery (in cargo compartment)
WARNING!
Check that the bonnet locks properly when you close it!
4. Radiator 5. Engine oil dipstick 6. Engine oil filling 7. Washer fluid reservoir 8. Power steering fluid reservoir 9. Expansion tank, cooling system
172
Diesel Fuel system Diesel engines are sensitive to contaminants. O nly use diesel fuel from a well-known oil company that fulfils the requirements for recommended fuel grade as described on page 244. Never use diesel of dubious quality. Special diesel fuel designed for outside temperatures around freezing point is available from the major oil companies. This fuel is less viscous at low temperatures and reduces the risk of wax building up in the fuel system. The risk of condensation building up in the tank is reduced if the tank is kept well filled. Make sure that the area around the filler pipe is clean when refuelling. Avoid spilling onto the paintwork. Wash off any spills with detergent and water. Empty tank No special procedures are required if the tank is run dry. The fuel system is bled automatically if the ignition switch is kept in position II for approx. 60 seconds before the start attempt.
IMPORTANT! Diesel type fuels which must not be used: special additives, Marine Diesel Fuel, fuel oil, RME (Rape Methyl Ester), vegetable oil. These fuels do not fulfil the requirements in accordance with Volvo recommenda- tions and generate increased wear and engine damage that is not covered by the Volvo warranty.
Draining condensation from the fuel filter The fuel filter separates condensation from the fuel. Condensation can disrupt engine operation. The fuel filter must be drained at the intervals specified in the Service and Warranty Booklet or if you suspect that the car has been filled with contaminated fuel.
Maintenance and service
173
Maintenance and service
Oils and fluids
Enginecompartmentdecalforoilgrade
IMPORTANT! Always use oil of the prescribed grade, see the engine compartment decal. Check the oil level frequently and change the oil regularly. The engine will be damaged if lower grade oil is used or if the car is driven with the oil level too low.
Volvo recommends oil products. Using oil of a higher than specified grade is permitted. Volvo recommends using an oil of a higher grade than that specified on the
174
decal for adverse driving conditions. See page 239. Adverse driving conditions Check the oil level more frequently for long journeys: (cid:127) (cid:127) (cid:127) at high speeds. (cid:127)
towing a caravan or trailer. in mountainous regions.
in temperatures colder than –30 °C or hotter than +40 °C.
(cid:127) shorter driving distances (shorter than
10 km) at low temperatures (under 5 °C). This may result in abnormally high oil temper- ature or oil consumption.
Checking and changing the engine oil and oil filter Change the oil and oil filter in accordance with the intervals specified in the Service and Warranty Booklet.
IMPORTANT! When filling oil to top up a low oil level, the oil being filled must be of the same grade and viscosity as the oil in the engine.
Checking the oil level in a new car is especially important before the first scheduled oil change. The Service and Warranty Booklet specifies the odometer readings for oil changes. Volvo recommends checking the oil level every 2500 km. The most accurate measure- ments are made on a cold engine before starting. The measurement will be inaccurate if taken immediately after the engine is switched off. The dipstick will indicate that the level is too low because the oil has not had time to flow down into the oil sump.
Oils and fluids
Maintenance and service
– Wipe the dipstick clean before checking
the level.
– Check the oil level using the dipstick. The
oil level must be between the MIN and MAX marks.
– If the level is close to the MIN mark, start by topping up with 0.5 litres of oil. Top up until the oil level is nearer the MAX than the MIN mark on the dipstick. See page 240 for capacities.
IMPORTANT! Never fill above the MAX mark. Oil consumption may increase if too much oil is poured into the engine.
WARNING!
Do not spill oil onto the hot exhaust manifold due to the risk of fire.
Theoillevelmustbewithintheareamarked onthedipstick Checking the oil in a cold engine: – Wipe the dipstick clean before checking
the level.
– Check the oil level using the dipstick. The
oil level must be between the MIN and MAX marks.
– If the level is close to the MIN mark, start by topping up with 0.5 litres of oil. Top up until the oil level is nearer the MAX than the MIN mark on the dipstick. See page 240 for capacities.
Checking the oil in a warm engine: – Park the car on a level surface, switch off
the engine and wait 10 – 15 minutes to allow the oil time to run back to the sump.
175
Maintenance and service
Oils and fluids
damage (cracks) to the cylin der head. Top up the coolant when the level falls to the MIN mark. NOTE! The engine must only be run with a well-filled cooling system. High temperatures can occur, causing a risk of damage (cracks) to the cylinder head.
IMPORTANT! Always use coolant with anti-corrosion agent as recommended by Volvo. New cars are filled with coolant that can withstand temperatures down to approximately –35 °C.
WARNING!
The coolant may be very hot. If the coolant requires topping up when the engine is at operating temperature, unscrew the expansion tank cap slowly to gently release the overpressure.
IMPORTANT! The engine must only be run with a well- filled cooling system. High temperatures can occur, causing a risk of damage (cracks) to the cylinder head.
Washer fluid reservoir The windscreen and headlamp washers have the same reservoir. See capacities and recommended grade for fluids and oils on page 242. Add frost protection in the winter so that the fluid does not freeze in the pump, reservoir and hoses. Tip: clean the wiper blades when topping up washer fluid.
Checking and topping up the coolant When topping up the coolant, follow the instructions on the packaging. It is important that the mixture of coolant concentrate and water is correct for the prevailing weather conditions. Never top up with water only. The risk of freezing increases with both too little and too much coolant concentrate. See capacities on page 242. Check the coolant regularly The level should lie between the MIN and MAX marks on the expansion tank. If the system is not filled sufficiently, high local temperatures could occur, causing a risk of
176
Oils and fluids
Maintenance and service
NOTE! The fluid should be changed annually for cars driven in conditions requiring hard, frequent braking, such as driving in mountains or tropical climates with high humidity.
WARNING!
If the brake fluid is under the MIN level in the brake fluid reservoir, do not drive further before topping up the brake fluid. The reason for the loss of brake fluid must be investigated.
Checking and topping up the brake and clutch fluid The brake and clutch fluid have a common reservoir1. The fluid level must be between the MIN and MAX marks. Check the level regularly. Change the brake fluid every other year or at every other regular service. See the capacities and recommended brake fluid grade on page 242.
1.
Location dependent on whether car is left or right-hand drive.
Checking and topping up the power steering fluid Check the level at every service. It is not necessary to change the fluid. The level should lie between the ADD and FULL marks. See the capacities and recommended grade on page 242. NOTE! If a fault should arise in the power steering system or if the car is without power and must be towed, it can still be steered. However the steering will be much heavier than normal and it will require more effort to turn the wheel.
177
– Press the entire wiper blade down so that
the wiper arm eye passes through the hold in the wiper blade mounting.
– Then pull the blade up so that the wiper arm eye passes beside the wiper blade mounting. Fit the new blade in reverse order and check that it is securely in place.
NOTE! Keep in mind that the wiper blade on the driver’s side is straight and has a spoiler while the one on the passenger side is curved. The spoiler on the driver’s side should sit on the lower side of the blade. The curve of the blade should follow the curve of the bottom edge of the windscreen.
Replacing rear window wiper blades – Fold out the wiper arm. – Remove the wiper blade by pulling it
outwards towards the tailgate.
– Press the new wiper blade into position.
Check that the blade fits securely!
Maintenance and service
Wiper blades
Changing the wiper blades – Fold out the wiper arm and hold the wiper blade at 45° to the wiper arm. Press in the spring on the wiper blade.
178
Battery
Battery care The function and life of the battery is affected by number of starts, number of times discharged, driving style, driving conditions, climate conditions, etc. Repeated use of the parking heater and similar large power consumers combined with short driving distances could lead to a discharged battery and thereby problems starting. For the battery to function satisfactorily, consider the following: (cid:127) Regularly check that the battery fluid level
is correct (A).
(cid:127) Check all cells. Use a screwdriver to
remove the caps. Each cell has its own maximum level mark. If necessary, top up with distilled water to the battery’s maximum mark.
(cid:127)
(cid:127) Never fill above the maximum mark (A).
IMPORTANT! Always use distilled or deionised water (battery water).
– Tighten the caps properly. NOTE! The life of the battery is shortened if it becomes discharged repeatedly. Symbols on the battery These symbols displayed on the battery. Use protective goggles.
Further information in the owner’s manual.
Maintenance and service
Store the battery out of the reach of children.
The battery contains corrosive acid.
Avoid sparks and naked flames.
Risk of explosion.
179
Maintenance and service
Battery
Draining oxyhydrogen gas The battery can develop oxyhydrogen, which is highly explosive. An evacuation hose draws any oxyhydrogen gas from around the battery out of the car and prevents gas from accumu- lating in the passenger and cargo compart- ments. If you must change the battery for some reason, it is imperative that the evacu- ation hose is connected to the new battery and that it is routed to the outlet in the bodywork.
Changing the battery Do as follows once you have unscrewed the console and battery cover and wish to remove the battery: – Check that the ignition is switched off. – Wait at least 5 minutes before touching any electrical terminals (so that the infor- mation in the car’s electrical system can be stored in the different control modules).
– Disconnect the negative lead first. – Then disconnect the positive lead and the
evacuation hose for the oxyhydrogen.
Do as follows when installing the battery: – Set the battery in place. – Connect the positive lead first. – Then connect the negative lead. – Make sure the evacuation hose is
correctly connected to both the battery and the outlet in the bodywork.
180
Battery
WARNING!
The battery contains oxyhydrogen, which is highly explosive. Be sure that the evacu- ation hose is correctly connected!
WARNING!
Batteries can generate oxyhydrogen gas, which is highly explosive. A spark, which can be generated if you connect the jump leads incorrectly, is sufficient to make the battery explode. The battery also contains sulphuric acid, which can cause serious burns. If the acid comes into contact with eyes, skin or clothing, flush with large quantities of water. If acid splashes into the eyes, seek medical advice immedi- ately.
Maintenance and service
181
Maintenance and service
Replacing bulbs General All bulb specifications are given on page 247. The following list contains bulbs and point- source lamps that are specialised or unsuitable for changing except at a workshop: (cid:127) General interior lighting in the roof (cid:127) Roof lighting (cid:127) Reading lamp (cid:127) Glovebox lighting (cid:127) Lamps, Bi-Xenon headlamps.
IMPORTANT! Never touch the bulbs’ glass with your fingers. Grease and oils from your fingers are vaporised by the heat, coating and damaging the reflector.
WARNING!
On cars with Bi-Xenon headlamps, all work on the lights should be carried out at an authorised Volvo workshop. Bi-Xenon headlamps must be handled with extreme care due to the high-voltage unit.
182
Replacing bulbs
Maintenance and service
– Unplug the connector by first pressing in
the catch from underneath and then pulling it up a bit from above.
– Lift out the entire headlamp insert and place it on a soft surface so as not to damage the lens.
Refit the headlamp insert in reverse order. Check that the lock pins are correctly situated.
Location of bulbs in front lamp 1. Dipped beam 2. Main beam 3. Direction indicator 4. Parking lamp 5. Side marker lamps
Dipped beam, main beam, direction indicator, parking lamp and side marker light The entire lamp insert must first be removed when replacing dipped beam, main beam and parking lamp bulbs. To replace one of these bulbs, do the following and then consult the instructions for the specific lamp. – Switch off all lights and turn ignition key
to position 0.
– Open the bonnet. – Release the insert by pulling up the two
lock pins holding it in place.
– Lift the insert straight out.
183
Maintenance and service
Replacing bulbs
Dipped beam lamp – Undo the outer cover by turning it
anticlockwise.
Main beam lamp – Undo the outer cover by pulling it straight
out.
– Unplug the connector. – Disconnect the spring clamp. First push
– Unplug the connector. – Disconnect the spring clamp. First push
to the right so that the spring clamp disconnects, then out and down.
to the right so that the spring clamp disconnects, then out and down.
– Pull out the bulb. – Fit the new bulb. It can only be fitted in
– Pull out the bulb. – Fit the new bulb. It can only be fitted in
one position.
one position.
– Press the spring clamp up and a little to
– Press the spring clamp up and a little to
Side marker lamps and position/ parking lamps The bulbs are housed in bayonet holders. – Turn the bulb holder anticlockwise and
remove.
– Pull the bulb straight out. – Fit the new bulb by carefully pressing it
into the recess.
– Fit the bulb holder back in place and turn
clockwise.
the left so that it fastens in its catch. – Press the connector back in place. – Screw the cover back into place; the marking "HAUT" should be at the top.
184
the left so that it fastens in its catch. – Press the connector back in place. – Refit the cover.
Replacing bulbs
Maintenance and service
Direction indicators The bulbs are housed in bayonet holders. – Turn the bulb holder anticlockwise and
remove.
– Press in the bulb, turn anticlockwise and
remove.
– Fit the new bulb by pressing it into the
recess and then turning clockwise.
Side indicator lamp – Switch off all lights and turn ignition key
Fog lamps – Switch off all lights and turn ignition key
to position 0.
– Prise out the lamp housing from under- neath using a small slotted screwdriver.
– Turn the bulb holder ¼turn anticlockwise
and pull straight out.
– Pull the defective bulb straight out. – Replace with a new bulb and press the
lamp straight in.
to position 0.
– Turn the bulb holder slightly
anticlockwise.
– Remove the lamp. – Put the new bulb in place. The profile of the bulb holder matches the one on the foot of the lamp.
– Refit the bulb holder by turning slightly
clockwise. "TOP" should be up!
185
Maintenance and service
Replacing bulbs
Location of bulbs in rear lamp cluster 1. Direction indicator 2. Brake light 3. Reversing lamp 4. Position lamps NOTE! If the error message "BULB FAILURE"/"CHECK BRAKE LIGHT" remains after a faulty bulb has been replaced then an authorised Volvo workshop needs to be consulted to rectify the fault.
186
C
Replacing bulbs
Bulbs in rear lamp cluster – Switch off all lights and turn the ignition
key to position 0.
– Lower the bottom of the tailgate and open
the floor hatch.
– If the car is equipped with a grocery bag
holder (option), loosen the holder’s retaining straps.
– Remove the corner piece (A). – Open the hatch (B) in the side panel by
pulling the catch (C) up and towards you.
– Take spanner no. 10 out of the tool kit. – Loosen the nuts (D). – Pull the entire insert straight back.
– Loosen the extra length of cable for better
accessibility.
– Place the insert on a soft surface so as
not to scratch the glass.
– Turn the bulb holder anticlockwise and
pull it out.
– Turn the bulb anticlockwise to loosen it. – Replace the bulb. – Refit the bulb holder in the recess and
turn clockwise.
– Press back the extra length of cable. – Refit the insert against the bolt holes.
Press the insert into place.
– Tighten the nuts. – Refit the side panel and corner piece.
Maintenance and service
187
Maintenance and service
Replacing bulbs
Rear fog lamp – Insert a slotted screwdriver as indicated
by the arrow in the illustration.
– Prise out the lamp insert. – Turn the lamp insert anticlockwise and
pull out the bulb. – Replace the bulb.
Number plate lighting NOTE! Applies to vehicles manufactured before week 9, 2006. – Switch off all lights and turn the ignition
key to position 0.
Number plate lighting NOTE! Applies to vehicles manufactured from and including week 9, 2006. – Switch off all lights and turn the ignition
key to position 0.
– Remove the screw with a screwdriver. – Carefully detach the entire lamp housing
– Remove the screws with a screwdriver. – Loosen the whole lamp housing carefully
and withdraw it. Turn the connector anticlockwise and pull out the bulb.
– Replace the bulb. – Refit the contact and turn clockwise. – Refit the entire lamp housing and screw it
into place.
and pull it out.
– Replace the bulb. – Refit the entire lamp housing and screw it
into place.
188
Replacing bulbs
Maintenance and service
Courtesy lighting Courtesy lighting is found under the dashboard on the driver and passenger sides. Do as follows to replace the bulb: – Insert a screwdriver and gently turn so
that the lamp housing comes loose.
– Remove the blown bulb. – Replace the bulb. Check that the bulb
lights.
– Refit the lamp housing.
Bulbs in the cargo compartment – Insert a screwdriver and gently turn so
that the lamp housing comes loose.
– Remove the blown bulb. – Replace the bulb. Check that the bulb
lights.
– Refit the lamp housing.
Vanity mirror – Insert a slotted screwdriver at the side of the centre clip in the bottom edge of the mirror. Lift up so the centre clip releases. – Slide the screwdriver from side to side so
that the outer clips release.
– Lift out the mirror insert. – Replace the bulbs. – Refit the insert top edge first. Be sure that
the upper clips are properly depressed before pressing the insert back.
189
Maintenance and service
Fuses
Cableroutingmayvaryslightlyduetoenginevariant.However,thecomponentslistedareinthesamepositions. All electrical functions and components are protected with a number of fuses to protect your car’s electrical system from damage by short-circuits or overloads. Fuses are housed in four different locations in the car: 1. Relay/fuse box in the engine
If an electrical component or function does not work, this may be because the component’s fuse was temporarily overloaded and blew. – Look in the fuse diagram to locate the
– Pull out the fuse and check from the side
fuse.
If the same fuse blows repeatedly, there is a fault in the component and you should contact an authorised Volvo workshop to have it checked.
compartment.
2. Fuse box in the passenger compartment
to see whether the curved wire has blown.
within the sound barrier on the driver’s side.
– If this is the case, replace it with a new fuse of the same colour and amperage.
3. Fuse box in the passenger compartment
at dashboard end on driver’s side.
4. Fuse box in cargo compartment.
There are a number of spare fuses in the cover on the end of the dashboard. There are also pliers which facilitate the removal and fitting of fuses.
190
Fuses
Maintenance and service
Pressintheplasticcatchesontheshortsidesoftheboxandpullthecoverupward. Relay/Fuse box in the engine compartment 1. ABS................................................................................................ 30 A 2. ABS................................................................................................ 30 A 3. High-pressure washer, headlamps .......................................... 35 A 4. Parking heater (option)................................................................ 25 A 5. Auxiliary lamps (option)............................................................... 20 A 6. Starter motor relay........................................................................ 35 A 7. Windscreen wipers...................................................................... 25 A 8. Transmission control module (TCM), (V8, diesel) ................. 15 A 9. Fuel pump ..................................................................................... 15 A 10.
Ignition coils (petrol), engine control module (ECM), injection valves, (diesel) .............................................................. 20 A
11. Accelerator pedal sensor (APM), AC compressor, fan
electronics box.............................................................................. 10 A
12. Engine control module (ECM) (petrol),
injection valves, (petrol), mass air flow sensor (petrol) ....... 15 A Mass air flow sensor (diesel) ....................................................... 5 A
13. Electronic throttle module (ETM) (diesel), solenoid valve, SWIRL (air mixing valve), fuel pressure regulator (diesel) ..................................................10 A 14. Lambda-sond (petrol) ..................................................................20 A Lambda-sond (diesel)..................................................................10 A 15. Solenoid valves, glow plugs (diesel) ........................................10 A
crankcase ventilation heater, solenoid valves mass air flow sensor (V8), petrol...............................................15 A 16. Dipped beam (left)........................................................................20 A 17. Dipped beam (right).....................................................................20 A 18. -................................................................................................................ - 19. Engine control module (ECM) supply, engine relay ................ 5 A 20. Position lamps ...............................................................................15 A 21. -................................................................................................................ -
191
Maintenance and service
Fuses
Adecalwhichindicatesthepositionsandamperagesofthefusesislocatedintheendboxcover. Fuses in the passenger compartment at dashboard end on driver’s side 1. Climate control system fan........................................................ 30 A 2. Amplifier ....................................................................................... 30 A 3. Power driver’s seat....................................................................... 25 A 4. Power passenger seat ................................................................ 25 A 5. Control module, left front door ................................................. 25 A 6. Control module, right front door .............................................. 25 A - ................................................................................................................- 7. - ................................................................................................................- 8. 9. Infotainment, RTI display, CD, MD .......................................... 10 A 10. OBDII, light switch (LSM), Steering Angle Sensor (SAS),
11. Ignition switch, SRS system, engine control module (ECM)
SRS deactivation passenger side (PACOS), immobiliser (IMMO), Transmission control module TCM (V8), diesel ..........................................................................7,5 A
12. General lighting, ceiling (RCM), upper electronic
module (UEM) ...............................................................................10 A 13. Sunroof............................................................................................15 A 14. Telephone ........................................................................................ 5 A 15-38 -..............................................................................................................-
Steering Wheel Module (SWM)..................................................5 A
192
Fuses
Maintenance and service
Fuses in the passenger compartment within the sound barrier on the driver’s side 1. Seat heating, right side............................................................... 15 A 2. Seat heating, left side.................................................................. 15 A 3. Horn ................................................................................................ 15 A - ................................................................................................................- 4. 5. Infotainment system..................................................................... 10 A 6. Reserve...................................................................................................- 7. Reserve...................................................................................................- 8. Siren...................................................................................................5 A 9. Brake lamp switch feed .................................................................5 A 10. Combined instrument panel (DIM), climate control
(CCM), parking heater, power driver’s seat ........................... 10 A 11. Front and rear seat socket ......................................................... 15 A 12. - ................................................................................................................-
13. Reserve .................................................................................................. - 14. -................................................................................................................ - 15. ABS, STC/DSTC ............................................................................5 A 16. Electronic power steering (ECPS), Bi-Xenon,
headlamp levelling ........................................................................10 A 17. Fog lamp, front left.......................................................................7,5 A 18. Fog lamp, front right ....................................................................7,5 A 19. Reserve .................................................................................................. - 20. Coolant pump (V8).........................................................................5 A 21. Transmission Control Module (TCM),
reverse gear inhibitor (M66) .......................................................10 A 22. Main beam, left..............................................................................10 A 23. Main beam, right ...........................................................................10 A 24. -................................................................................................................ - 25. -................................................................................................................ - 26. Reserve .................................................................................................. -
193
Maintenance and service
Fuses 27. Reserve...................................................................................................- 28. Power passenger seat ...................................................................5 A 29. Reserve...................................................................................................- 30. BLIS ...................................................................................................5 A 31. Reserve...................................................................................................- 32. Reserve...................................................................................................- 33. Vacuum pump ............................................................................... 20 A 34. Washer pump ............................................................................... 15 A 35. - ................................................................................................................- 36. - ................................................................................................................-
194
Fuses
Maintenance and service
Fuses in the cargo compartment 1. Reversing lamp..............................................................................10 A 2. Position lamps, fog lamps, cargo area lighting,
number plate lighting, LEDs in brake lighting .........................20 A 3. Accessories (AEM).......................................................................15 A 4. Reserve .................................................................................................. - 5. REM electronics............................................................................10 A 6. RTI, radio receiver, RSE..............................................................7,5 A 7. Towing bracket wiring (30-feed)................................................15 A 8. Cargo compartment socket........................................................15 A 9. Rear right door: power window, power window lock............20 A 10. Rear left door: power window, power window lock ..............20 A 11. Reserve .................................................................................................. - 12. Reserve .................................................................................................. - 13. Diesel filter heater.........................................................................15 A 14. Subwoofer, rear air conditioning (AC)......................................15 A 15. Reserve .................................................................................................. - 16. Reserve .................................................................................................. - 17. Infotainment system accessories ................................................5 A 18. Reserve .................................................................................................. - 19. Rear wiper ......................................................................................15 A 20. Towing bracket wiring (15-feed)................................................20 A 21. Reserve .................................................................................................. - 22. -................................................................................................................ - 23. AWD ...............................................................................................7,5 A 24. Reserve .................................................................................................. - 25. -................................................................................................................ - 26. Parking assistance..........................................................................5 A
195
Maintenance and service
Fuses 27. Main fuse: Towing bracket wiring, parking assistance,
AWD .............................................................................................. 30 A 28. Central locking system (PCL) ................................................... 15 A 29. Trailer lighting, left: position lamps, direction indicator ........ 25 A 30. Trailer lighting, right: brake lamp, rear fog lamp,
direction indicator ........................................................................ 25 A 31. Main fuse: Fuse 37, 38............................................................... 40 A 32. - ................................................................................................................- 33. - ................................................................................................................- 34. - ................................................................................................................- 35. - ................................................................................................................- 36. - ................................................................................................................- 37. Heated rear window .................................................................... 20 A 38. Heated rear window .................................................................... 20 A
196
Infotainment system Control panels, audio Audio system functions Radio functions CD/MD (option) CD changer (option) Menu structure – Audio Telephone (option) Telephone functions Menu settings and options – Telephone
Infotainment system 198
199
204
208
216
218
220
222
224
231197
Infotainment system
Infotainment system Information – Entertainment Infotainment is a system with integrated audio and telephone functions. You can easily and conveniently use your Infotainment system by means of the joint control panel or the steering wheel keypad. The control panel display indicates the current function. XC90 can be equipped with Dolby Surround Pro Logic II (Premium Sound), which offers an optimal sound experience very close to being there with a broad, natural sound profile. The system also allows your passengers to use headphones (option) with separate sound sources.
198
Control panels, audio
Infotainment system
20
19
18
17
161. On/Off – Audio 2. Volume 3. CD – shortcut button 4. AM/FM -shortcut button to switch
between FM1, FM2 and AM
5. Display 6. ENTER – select in the menu, activate a selection or activate the telephone from standby mode
7. On/Off/Standby – Telephone 8. MY KEY – programmable shortcut key
for your favourite function
9. SELECTOR – select sound source 10. SOUND – make sound settings
11. EXIT/CLEAR – scroll back in the menu, cancel a selection, put the telephone in standby mode, or erase the previous character when entering text and numbers
12. SIM card holder 13. Menu selection buttons 14. MD eject 15. CD and CD changer eject 16. CD player and CD changer (option) 17. MD player (option) 18. Station setting buttons/selecting CD
changer position (1-6), number/ character buttons for the telephone and menu shortcuts
10
11
12
13
14
1519. IR receiver for remote controls (option) 20. Seek/change tracks/stations or scroll forward and back when entering text and digits
199
Infotainment system
Control panels, audio
Steering wheel keypad Audio – Telephone The four buttons at the bottom of the steering wheel keypad control both the radio and the telephone. The function of the respective button depends on which system is active. The steering wheel keypad can be used to adjust volume, shift between preset stations and change CD/MD tracks.
or
By holding the button depressed you can fast forward or rewind in a song or search for a radio station. To use these buttons for the telephone functions, the telephone must be active, see page 225. To make audio system settings with these buttons, the telephone must be in standby mode (deactivated).
200
Menus In menu mode, you can check or modify settings and programme new functions in the system. The different menu alternatives are shown in the display. Menu alternatives followed by periods indicate that there are several submenus. Press the MENU button (1) to activate menu mode. The following applies in menu mode: – The menu selection buttons are used to
scroll up or down in the menu.
– A long press on EXIT/CLEAR allows you
to leave menu mode.
– A brief press on EXIT/CLEAR allows you to clear, cancel, decline an alternative or go back one step in the menu structure. – A press on ENTER allows you to confirm,
select or scroll from a submenu to the next submenu.
Control panels, audio
Headphone sockets (option) The door panels behind the second row of seats contain headphone sockets. This means that several passengers can listen to different sound sources, such as CDs or the radio, at the same time without disturbing each other. Two sets of headphones can be connected to each socket. – Switch sound source with the SEL
button.
– Use the arrow keys,
, to change CD/MD tracks or switch between preset stations.
or
(cid:127)
or
– Hold the
button depressed to fast forward/rewind or search for the next strong station.
– Hold the SEL button depressed to switch
off the system.
– Use the volume control button to adjust
the volume of the respective headphones.
All headphones are switched off automati- cally when the audio system is switched off with the ignition key and must be activated manually when the car is restarted. For the best sound reproduction, we recommend headphones with impedance between 16–32 ohm. The sensitivity of these should be equal to or greater than 102 dB. The headphone socket is intended for 3.5 mm contacts and is located on the bottom of the headphone panel (1). Headphones – limitations (cid:127)
If a set of headphones is connected to the same source that is being sent through the speakers, the headphones controls cannot be used to change track or station. This is so the driver is not surprised by an unexpected change in music. If the driver uses the control panel to select the same sound source as
Infotainment system
someone wearing headphones, the driver takes control of the sound source.
(cid:127) Headphone users can choose from
among the presets of the frequency (AM, FM1, FM2) previously set by the driver. In some cases, this means that the driver will not receive NEWS - or traffic infor- mation even if TP/NEWS is selected.
(cid:127) The CD changer can only play one disc
and one song at a time.
201
Infotainment system
Control panels, audio
8. Function not available 9. On/Off – Audio
Display The display (2) shows the current function, such as menu alternatives, messages, telephone numbers, or settings. Clean the display with a soft, dry cloth. Do not use cleaning agent.
Remote control (option) 1. Memory – Stores radio stations. To
store a station:
– Press the Memory button – Select Preset using Preset/Disc (5) – Confirm your selection using the Memory
button
2. Volume 3. Seek/change tracks forward or back 4. Source – switch sound source 5. Preset/Disc – select CD changer
position or preset radio station
6. Auto – find and store the strongest
stations
7. Function not available
202
Control panels, audio
Infotainment system
Direct the remote control towards the IR receiver (see illustration) that is located in the dashboard. NOTE! The remote control contains AAA batteries (R03). If the remote control does not work, first try replacing the batteries.
203
Infotainment system
Audio system functions
– Press the AM/FM button repeatedly to
scroll between FM1, FM2 and AM.
The selected sound source is shown on the display. MD can only be chosen using the SELECTOR knob.
On/Off switch – Audio Press the POWER button (1) to switch the audio system on or off. If the audio system is active when the ignition is switched off, it will reactivate automatically when the car is restarted. Selecting the sound source There are two ways to select sound source: By using the shortcut buttons CD (2), AM/ FM (3) or by using the SELECTOR knob (4): – Turn the SELECTOR knob to select Radio (FM1, FM2 or AM), CD/CD changer (option) or MD (option).
204
Volume control Turn the knob (1) clockwise or anticlockwise to raise or lower the volume, respectively. The volume control is electronic and has no end position. Volume can also be raised (+) or lowered (–) using the steering wheel keypad. Pause mode When volume is in position zero, the CD/MD player is put in pause mode. Reactivate the player by turning up the volume.
Audio system functions Volume control – TP/PTY/ NEWS/ALARM If a CD or the like is playing when the radio receives a traffic bulletin, the CD player is put in pause mode. The message is played at the volume selected for that type of message. Playback of the originally selected sound source is then resumed at the previous volume. If volume is adjusted while the bulletin is played, the new volume is saved and used for the next bulletin.
Audio settings – Press the SOUND button (1). – Press the SOUND button repeatedly until you come to the function you wish to set. Choose BASS, TREBLE, FADER, BALANCE, SUBWOOFER (option), CENTRE (option) or SURROUND (option).
– Use the SELECTOR knob (2) to adjust
the level. The display shows a scale from min. to max. position. The middle indicates the normal position.
NOTE! The level for the centre speaker can only be set if Dolby Pro Logic II (DPL II) or
Infotainment system
three-channel stereo (3-CH) has been selected from the menu. The level for Surround can only be set if Dolby Pro Logic II has been selected in the menu. The level for Subwoofer can only be set if Subwoofer is activated.
Audio settings
Bass Treble Balance between the left and right-hand speakers Balance between the front and rear speakers Level for subwoofer
Level for centre speaker
Level for surround sound
Shown on the display BASS TREBLE BALANCE
FADER
SUBWOOFER (option)
