Login- Download PDF Manual
-
Volvo workshop.
Engine preheater (diesel)
This lamp lights to indicate that the engine is being preheated. You can start the car when the lamp goes out. Applies to cars with diesel engines only.
45
Instruments and controls
Indicator and warning symbols Parking brake applied
The lamp comes on when the parking brake is depressed. Always depress the parking brake to the bottom position.
NOTE! The lamp comes on irrespective of how hard the parking brake is depressed. Rear fog lamp
This lamp lights when the fog lamp is on.
Trailer indicator lamp
Flashes when the direction indicators of the car and trailer are used. If the lamp does not flash, one of the direction indicators on the trailer or car is defective. Stability system and DSTC The DSTC system contains several different functions that are described in more detail on page 124. The symbol lights and goes out again after approx. two seconds
The symbol is lit for a system check when the car is started.
46
The symbol flashes
The SC function acts to prevent the car’s drive wheels from spinning. The TC function acts to improve the car’s traction.
The AYC function acts to prevent skidding. The RSC function acts to prevent overturning. The warning symbol shines with a steady amber glow
TRACTION CONTROL TEMPORARILY OFF is shown on the information display together with the symbol.
The TC function has been temporarily suppressed because the brake temperature is too high. Automatic reactivation of the function takes place when the brake temperature has returned to normal. The warning symbol shines with a steady amber glow
ANTI-SKID SERVICE REQUIRED is shown on the information display together with the symbol.
The DSTC system has been switched off because of a fault. – Stop the car in a safe place and turn off
the engine.
– Restart the engine. If the warning symbol remains lit, drive to an authorised Volvo workshop to have the system checked. Fault in DSTC system If the warning symbol lights and shines with a constant glow even though you did not switch off the system, it indicates a fault in one of the systems. The text "ANTI-SKID SERVICE REQUIRED" is shown in the display. – Stop the car in a safe place and switch off
(cid:127)
(cid:127)
the engine. Restart the engine. If the warning symbol goes out, the fault was temporary and it is not necessary to visit a workshop. If the warning symbol remains lit, drive to an authorised Volvo workshop to have the system checked.
WARNING!
Under normal driving conditions, the DSTC system improves the car’s road safety, but this should not be taken as a reason to increase speed. Always follow the usual precautions for safe cornering and driving on slippery surfaces.
Information display
Instruments and controls
messages stored in the memory by pressing the READ button. Press the READ button to return read messages to the memory. If a warning message interrupts when you are in the trip computer menus or wish to use the telephone, you must first acknowledge the message by pressing the READ button (A).
Messages on the display Any warning or indicator symbol that appears is accompanied by a message in the display. Once you have read and understood the message, press the READ button (A). Messages which have been read are cleared from the display and stored in the car’s memory. Fault messages will remain in the memory until the fault has been remedied. Very serious fault messages cannot be erased from the display. They remain in the display until the fault is remedied. Messages stored in the memory can be read again. Press the READ button (A) to see stored messages. Scroll through the
47
Instruments and controls
Information display
Message
Specification
STOP SAFELY STOP ENGINE SERVICE URGENT SEE MANUAL SERVICE REQUIRED FIX NEXT SERVICE TIME FOR REGULAR SERVICE
OIL LEVEL LOW1 – FILL OIL3
OIL LEVEL LOW2 – STOP SAFELY3
OIL LEVEL LOW2 – STOP ENGINE3OIL LEVEL LOW2 – SEE MANUAL3
Stop and switch off the engine. Serious risk of damage. Stop and switch off the engine. Serious risk of damage. Take your car in for service immediately. Consult your owner’s manual. Take your car in for service as soon as possible. Have your car checked at the next service interval. When this message is shown, the car is due for a service. When the message is displayed is affected by the distance travelled, number of months since last service and engine running time. Low engine oil level. Check and remedy as soon as possible. See page 174 for more information. Low engine oil level. Stop the car safely and check the oil level. See page 174. Low engine oil level. Stop the car safely, switch off the engine and check the oil level. See page 174. Low engine oil level. Stop the car safely, switch off the engine and check the oil level. See page 174. Diesel particle filter requires regeneration. See page 115.
SOOT FILTER FULL – SEE MANUAL1
1. Displayed together with yellow warning triangle. 2. Displayed together with red warning triangle. 3. Only applies to engine variants with oil level sensor.48
Switches in the centre console
Instruments and controls
NOTE! The order of the buttons may vary. DSTC system
This button is used to reduce or reactivate the functions of the DSTC system. When the LED in the button is lit, the DSTC system is activated (assuming there is no fault).
NOTE! Hold the button depressed for at least half a second to reduce the function of the DSTC system. The LED in the button goes out and the text "DSTC SPIN CONTROL OFF" is shown on the display. Deactivate the system if you must use a wheel of a different size than the other wheels. The DSTC system is reactivated when the engine is restarted.
WARNING!
Keep in mind that the driving character- istics of the car change if you deactivate the DSTC system.
Air conditioning in the rear of the passenger compartment (option)
Press the button to activate the air conditioning in the rear of the passenger compartment. Rear air conditioning is deactivated when the ignition is completely switched off.
Child safety locks in the rear doors (option)
Use this button to activate or deactivate the electric child safety locks in the rear doors. The ignition key must be in position I or II. When the child safety locks are activated, the LED in the button lights. A message is shown on the display when the child safety locks are activated or deacti- vated.
49
Instruments and controls
Switches in the centre console Retractable door mirrors (option)
This button is used to fold in the door mirrors if they are folded out or to fold them out if they are folded in. Do as follows if a door mirror has been accidentally folded in or out:
– Manually adjust the appropriate door
mirror to its normal position.
– Turn the ignition key to position II. – Fold the door mirror inward and then outward using the button. The door mirrors have now returned to their original fixed positions.
Parking assistance (option) The system is always activated when the car is started. Press the button to deactivate/reactivate the parking assistance system. See also page 125.
Deactivation of the deadlocks1
and detectorsUse this button when you wish to switch off the deadlock function (doors cannot be opened from the inside when locked). This button can also be used
when deactivating the alarm system2
movement and tilt detectors. The LED lights when these systems are deactivated. Auxiliary lamps (accessory)Use this button to switch the auxiliary lamps on with main beam or to switch them off. The LED in the button is lit when the function is activated.
Electric socket, (standard)/ Cigarette lighter (option)
The electric socket can be used for various 12 V acces- sories, e.g. mobile phone or a cooler box. The ignition key must be at least in position I so that the socket can supply power. The cigarette lighter is activated by pushing in the button. Once the lighter has been heated, the button pops out again. Pull out the lighter to use it. For safety reasons, always keep the cover in place when the socket is not in use. Maximum current tap 10 A. BLIS – Blind Spot Information System (option)
Press the button to deactivate or reactivate the function. See page 143 for further infor- mation.
50
1. 2.
Certain markets Option
Switches in the centre console
Instruments and controls
Rear window and door mirror defrosters
Use the defroster to remove ice and misting from the rear window and door mirrors. Press the switch to start defrosting the rear window and door mirrors. The LED in the switch comes on. Defrosting is automati- cally disconnected after about 12 minutes. Heated front seats
See page 71 or 75 for further information.
Hazard warning flashers Use the hazard warning flashers (all direction indicators flash) when the car is stopped where it could be a traffic hazard or obstruction. Press the button to activate the function. NOTE! Regulations regarding the use of hazard warning flashers vary from country to country.
51
Instruments and controls
Lighting panel
Headlamp levelling The load in the car changes the vertical alignment of the headlamp beam, which could dazzle oncoming motorists. Avoid this by adjusting the height of the beam. – Turn the ignition key to position II. – Turn the headlamp control (1) to one of
the end positions.
– Roll the control up or down (3) to raise or
lower beam alignment.
Cars with Bi-Xenon headlamps1 have automatic headlamp levelling, so there is no control (3).
Option.
1. 52
Position/parking lamps The position lamps/parking lamps can be switched on irrespective of ignition key position. – Turn the headlamp control (1) to the
centre position.
In ignition key position II the position lamps/ parking lamps are always on. The number plate lighting is switched on at the same tome as the position lamps/parking lamps. Headlamps Automatic dipped beam Dipped beam comes on automatically when the ignition key is turned to position II, except when the headlamp control (1) is in the centre position. If necessary the automatic dipped beam can be deactivated by an authorised Volvo workshop. Manual dipped beam (certain countries) – Turn the ignition key to position II. – Turn the headlamp control (1) clockwise
to the end position.
Main beam – Turn the ignition key to position II. – Turn the headlamp control (1) clockwise
to the end position.
– Move the left-hand stalk switch towards
the steering wheel to the end position and release it, see page 53.
Fog lamp NOTE! Regulations for use of fog lamps vary from country to country. Front fog lamps (option) The front fog lamps can be switched on along with the headlamps or the position lamps/ parking lamps. – Press the button (2). The LED in the button (2) lights when the front fog lamps are switched on. Rear fog lamp The rear fog lamp can only be switched on with the headlamps or the front fog lamps. – Press the button (4). The rear fog lamp indicator symbol in the combined instrument panel and the LED in the button (4) come on when the rear fog lamp is switched on. Instrument lighting The instrument lighting is switched on when the ignition key is in position II and the headlamp control (1) is in one of the end positions. The lighting is automatically dimmed during the day and can be controlled manually at night. – Roll the control up or down (5) for
brighter or dimmer lighting.
Left-hand stalk switch
Stalk switch positions 1. Short flash sequence, direction
indicators
2. Continuous flash sequence, direction
indicators
3. Main beam flash 4. Switching, main and dipped beam, and
home safe lighting
Direction indicators Continuous flash sequence – Move the stalk switch up or down to end
position (2).
The stalk switch remains in its end position and is moved back manually, or automatically by steering wheel movement.
Short flash sequence – Move the stalk switch up or down to
position (1) and release.
When the stalk switch is released it returns to its start position and the direction indicators are switched off. Switching, main and dipped beam The ignition key must be in position II for main beam to be switched on. – Turn the headlamp control clockwise to
the end position, see page 52.
– Move the stalk switch towards the
steering wheel to the end position (4) and release.
Main beam flash – Move the stalk switch gently towards the
steering wheel to position (3).
Main beam comes on until the stalk switch is released. Home safe lighting Some of the exterior lighting can be kept switched on and works as home safe lighting after the car has been locked. The time delay is 30 seconds1, but can be changed to 60 or 90 seconds by an authorised Volvo workshop.
1.
Factory settings.
Instruments and controls
– Remove the key from the ignition. – Move the stalk switch towards the
steering wheel to the end position (4) and release.
– Get out of the car and lock the door.
53
Instruments and controls
Right-hand stalk switch
Wiper/washerfunction–windscreen. Windscreen wipers
Windscreen wipers off.
If the lever is in the 0 position and you move it upwards, the wipers will sweep one stroke at a time for as long as you hold the lever up. Intermittent wiping
You can adjust and set a suitable speed for intermittent wiping.
Rotate the ring (1) clockwise to increase wiper stroke frequency. Rotate the ring anticlockwise to decrease wiper stroke frequency.
54
To turn the rain sensor off, either: – press the button (2) or – press the stalk switch downward to
another wiper programme. If the stalk switch is raised, the rain sensor will remain active, the wipers make an extra sweep and then return to rain sensor mode when the stalk switch is released back to position 0.
The rain sensor is automatically deactivated when the key is removed from the ignition switch or five minutes after the ignition is switched off.
IMPORTANT! In an automatic car wash: Turn off the rain sensor by pressing the button (2) while the ignition key is in position I or II. Otherwise, the windscreen wipers may start and be damaged.
Wipers operate at "normal" speed. Wipers operate at "high" speed.
IMPORTANT! Use plenty of washer fluid when the wipers are cleaning the windscreen. The windscreen must be wet when the windscreen wipers are operating.
Rain sensor (option) The rain sensor automatically activates the windscreen wipers based on how much water it detects on the windscreen. The sensitivity of the rain sensor can be adjusted using the ring (1). – Turn the ring clockwise to increase sensi- tivity or anticlockwise to decrease sensi- tivity. (There is an extra swipe when the ring is turned clockwise).
On/Off When activating the rain sensor, the ignition key must be in position I or II and the windscreen wiper stalk switch must be in position 0. To activate the rain sensor: – press the button (2). An LED in the
button comes on to indicate that the rain sensor is active.
Right-hand stalk switch Windscreen washer Pull the lever towards the steering wheel to activate the windscreen washer. Headlamp washer (option on certain markets) High-pressure wash of the headlamps consumes a great deal of washer fluid. To save fluid, the headlamps are only washed every fifth time (within a ten minute period). If ten minutes have elapsed since the last windscreen washing, the headlamps receive a high-pressure wash the next time the windscreen is washed. Reduced washing If only approx. one litre of washer fluid remains in the reservoir, the supply to the headlamps and the rear window is cut off in order to prioritise cleaning of the windscreen.
Wiper/washerfunction–rearwindow. Rear window washer and wiper Move the lever forward to start the rear window washer. 1. Rear window wiper – intermittent wiping 2. Rear window wiper – normal speed Wiper – reversing If you engage reverse gear when the windscreen wipers are already activated, the rear window wipers will go into intermittent wiping mode1. If the rear window wiper is already engaged at normal speed, there is no change to the selected function.
1.
This function (intermittent wiping when reversing) can be deactivated. Contact an authorised Volvo workshop.
Instruments and controls
55
NOTE! There may be a slight error in the reading if a fuel-driven heater is used. Range to empty fuel tank The range to empty is calculated based on the average fuel consumption over the last 30 km. When the range to empty is shorter than 20 km then "----" is shown on the display. NOTE! There may be a slight error in the reading if fuel consumption is changed due to a change in driving style or if a fuel-driven heater is used for example.
Instruments and controls
Trip computer
Controls To access the trip computer information, you must turn the ring (B) in steps, either forward or backward. By turning again, you return to the starting point. NOTE! If a warning message interrupts while you are using the trip computer, you must first acknowledge the message by pressing the READ button (A) to return to the trip computer. Functions The trip computer displays the following information: (cid:127) AVERAGE SPEED
56
(cid:127) SPEED IN MILES PER HOUR1
(cid:127) CURRENT FUEL CONSUMPTION (cid:127) AVERAGE FUEL CONSUMPTION (cid:127) RANGE TO EMPTY FUEL TANK Average speed The average speed since the last reset (RESET). When the ignition is switched off, the average speed is stored and used as the basis of the new value when you continue driving. This can be reset with the RESET button (C) on the lever. Speed in miles per hour1
Current speed is displayed in mph. Current fuel consumption Continuous information on current fuel consumption, calculated each second. The figure in the display is updated every couple of seconds. When the car is stationary, "----" is shown on the display. NOTE! There may be a slight error in the reading if a fuel-driven heater is used. Average fuel consumption The average fuel consumption since the last reset (RESET). The average fuel consumption is stored when the ignition is switched off and remains until reset with the RESET button (C) on the lever.1.
Certain countries
Cruise control
Instruments and controls
Increasing or decreasing speed Increase or decrease the speed by pressing and holding + or –. The speed of the car when the button is released is set as the new speed. A brief press (less than half a second) on + or – changes the speed by one km/h. NOTE! A temporary increase in speed (less than one minute) using the accelerator, such as while overtaking, does not affect the cruise control setting. When you release the accel- erator, the car will return to the programmed speed. Temporary disengagement Press 0 to disengage the cruise control temporarily. CRUISE will be shown on the combined instrument panel. The speed set earlier is stored in the memory. The cruise control is also temporarily disen- gaged when: (cid:127)
the brake pedal or clutch pedal is depressed
(cid:127) speed falls below 30 km/h when
travelling uphill the gear selector is moved to position N
(cid:127) (cid:127) wheel spin or wheel lock-up occurs (cid:127) a temporary increase in speed lasts
longer than one minute.
Return to the set speed
Press this button to resume the previously set speed. CRUISE-ON appears on the combined instrument panel.
Disengaging Press CRUISE to disengage the cruise control. CRUISE-ON goes out on the combined instrument panel.
57
Activating The controls for cruise control are to the left of the steering wheel. Setting the desired speed: – Press the CRUISE button. CRUISE is
shown on the combined instrument panel.
– Touch + or – to lock the vehicle speed. CRUISE ON appears on the combined instrument panel.
Cruise control cannot be engaged at speeds below 30 km/h or above 200 km/h.
Instruments and controls
Parking brake, bonnet, electric socket, etc.
Activate the parking brake: – Press the foot brake down firmly. – Depress the parking brake to the end
position (1).
– Release the foot brake and make sure
that the car is stationary.
– Move the gear selector into position:
1 for manual gearbox P for automatic transmission.
Parking on a hill (cid:127)
If the car is parked uphill, turn the wheels away from the kerb. If the car is parked downhill, turn the wheels toward the kerb.
(cid:127)
Release the parking brake: – Press the foot brake down firmly. – Pull out the handle (2).
Parkingbrake,RHDcar.
Parkingbrake,LHDcar. Parking brake The parking brake is located to the left at floor height and acts on the rear wheels when it is depressed. The warning symbol in the combined instrument panel comes on irrespective of how hard the parking brake is depressed. So always depress the parking brake to the end position.
58
Parking brake, bonnet, electric socket, etc.
Instruments and controls
Opening the bonnet Pull the handle towards you to release the bonnet lock mechanism.
WARNING!
Close the bonnet by placing your hand on its top and pressing down. Do not close it by holding the grille. Engine components on the inside could injure your fingers.
Electrical socket for rear seat passengers (option) The electric socket can be used for various 12 V accessories, such as mobile phones or CD players. The maximum current is 10 A. The ignition key must be at least in position I so that the socket can supply power.
Steering wheel adjustment The steering wheel can be adjusted both vertically and front-rear. Press down the control on the left-hand side of the steering column. Then adjust the steering wheel to the position that suits you best. Press the control back into place to lock the steering wheel. If this is difficult, press the steering wheel slightly while pressing the control back.
WARNING!
Adjust the steering wheel before driving, never while driving. Ensure that the steering wheel is locked.
59
Instruments and controls
Parking brake, bonnet, electric socket, etc.
Opening the tailgate Open the tailgate by pulling the handle indicated in the illustration. Fold down the rear flap by lifting the handle up.
60
Power windows The power windows are operated using the controls in the door armrests. The ignition key must be turned to position I or II for the power windows to work. Once you finish driving and remove the ignition key, the windows can still be opened or closed as long as neither of the front doors has been opened. Open a window by depressing the front of the control, and close it by pulling up the front of the control.
WARNING!
If there are children in the car: (cid:127) Remember to switch off the supply to the power windows by removing the ignition key if the driver leaves the car. (cid:127) Make sure that children’s and other passengers’ hands are clear when closing the windows. If the rear door windows are operated from the driver’s door: (cid:127) Check that none of the rear seat passengers are in danger of getting their hands caught when closing the windows.
Instruments and controls
Power windows in the front doors Windows can be opened or closed from the front seat two ways. – Press the control (A) slightly down or pull
it slightly up. The power windows go up or down as long as the switch is actuated.
– Press the control (A) all the way down or
pull it all the way up, and then release. The windows then open or close automat- ically. Movement is stopped if the window is blocked in any way.
NOTE! The function auto up for the passenger side is only available in certain markets.
Controls(B)tooperatewindowsintherear doors. Blocking power windows in the rear doors The power windows in the rear seat can be blocked with the switch on the driver’s door control panel. Always remember to switch off current to the power windows (i.e. remove the ignition key) if you leave children in the car unattended. LED in the switch is unlit The rear door windows can be operated both with the control on each rear door and with the controls on the driver’s door.
61
Instruments and controls
Power windows LED in the switch is lit The rear door windows can only be operated from the driver’s door.
Power window in the front passenger seat The control for the power window at the front passenger seat operates that window only.
Power windows in the rear doors The rear door windows can be operated with the controls on the doors and the switch on the driver’s door. If the LED in the switch for blocking power windows in the rear doors (located in the driver’s door control panel) is lit, the rear door windows can only be operated from the driver’s door.
WARNING!
If rear door windows are being operated from the driver’s door, check that no rear seat passenger are in danger of getting pinched when the windows close.
62
Rearview mirror, door mirrors and side windows
Interior rearview mirror A. Normal position. B. Dimming position. Use this if headlamps
from the car behind are irritating you. Certain models have an auto-dim function (option). Dimming occurs automatically based on comparative light relationships. An authorised Volvo workshop can adjust the sensitivity.
WARNING!
Adjust the mirrors before you begin driving!
Door mirrors The controls for adjusting the two door mirrors are at the front of the driver’s door armrest. – Press the L or R button (L = left door
mirror, R = right door mirror). The LED in the button lights.
– Adjust the position with the adjustment control in the centre. Press the button again. The LED should no longer be lit.
Instruments and controls
IMPORTANT! Use the defroster (see page 51) to remove ice from the mirrors, not an ice scraper. The scraper could scratch the mirror glass.
Door mirrors with memory function (option) If the car has door mirrors with memory function, they work together with the memory setting of the seat, see page 81. Memory function in the remote control (option) When you unlock the car with one of the remote controls and change the setting of the door mirrors, these new settings are saved in the remote control. The next time you unlock the car with the same remote control and open the driver’s door within five minutes, the mirrors will assume their stored positions. Laminated side windows (option) The laminated windows in the front and rear doors improve sound insulation in the passenger compartment and provide better protection against unauthorised entry.
63
Instruments and controls
Rearview mirror, door mirrors and side windows Water and dirt-repellent coating on the front windows and/or door mirrors (option) The front windows and/or door mirrors are treated with a coating that ensures that the view through the windows or in the mirrors is good even if it is raining. For information on glass care, see page 165.
IMPORTANT! Do not use a metal ice scraper to remove ice from the windows. The water and dirt- repellent coating could be damaged. Use the defroster to remove ice from the mirrors!
Side windows and mirrors treated with the water and dirt-repellent coating are marked with a small symbol.
Rearview and door mirrors In certain weather conditions, the function of the dirt-repellent coating is improved if the door mirror defrosters are used, see page 51. Defrost the door mirrors: (cid:127) (cid:127) (cid:127)
if they are covered with ice or snow in heavy rain and dirty road conditions if they are misted.
64
Power sunroof (option)
Open positions Sunroof controls are located in the headlining. The sunroof can be opened in two different ways: A. Raise/lower trailing edge – ventilation
position
B. Rearwards/forwards – opening
position/comfort position1. The ignition key must be in position I or II.
1.
In comfort position, the sunroof is not completely open in order to reduce the level of wind noise.
Instruments and controls
WARNING!
If there are children in the car: remember to switch off the supply to the power sunroof (remove the ignition key) if the driver leaves the car.
1. Automatic closing 2. Closing, manual 3. Opening, manual 4. Opening, automatic 5. Opening, ventilation position 6. Closing, ventilation position Ventilation position Open: Push the trailing edge of the control (5) upward. Close: Pull the trailing edge of the control (6) downward. Switch from ventilation position to comfort position: pull the control rearwards to its end position (4) and release.
65
WARNING!
The sunroof’s pinch protection function only operates during automatic closing, not during manual closing. Make sure children’s hands are clear when closing the sunroof.
Instruments and controls
Power sunroof (option) Automatic operation Move the control over the resistance point position (3) to the rearmost end position (4) or over the resistance point position (2) to the front end position (1) and release. The sunroof will open to the comfort position or will close completely. In order to open from comfort position to maximum opening: Pull the control to the rear once more to the end position (4) and release. Manual operation Open: Pull the control rearwards to the resistance point position (3). The sunroof will move towards maximum opening position as long as the control is held in this position. Close: Press the control forward to the resistance point (2). The sunroof moves towards closing position as long as the control is held in this position.
WARNING!
If you have children in the car, make sure that their hands are clear when closing the sunroof.
66
Sunscreen The sunroof features a manual, sliding interior sunscreen. The sunscreen slides back automatically when the sunroof is opened. Grip the handle and slide the screen forwards to close the screen. Pinch protection The sunroof’s pinch protection function is activated if the hatch is blocked by an object. If blocked, the sunroof will stop and automat- ically open to the previous position.
General information on climate control Manual climate control, A/C Electronic Climate Control, ECC Parking heater (option)
Climate control 68
70
73
7667
Condensation In warm weather, condensation from the air conditioning system may drip under the car. This is normal. Fuel economy With ECC, the air conditioning system is controlled automatically and is used just enough to cool the passenger compartment and to adequately dehumidify the incoming air. This provides better fuel economy compared to conventional systems where the air conditioning cools the air to just above freezing point.
Climate control
General information on climate control Misting windows Reduce the problem of windows misting up on the inside by cleaning the windows. Use a regular window cleaner. Particle filter Make sure the particle filter is replaced regularly. Consult an authorised Volvo workshop. Ice and snow Remove ice and snow from the climate control air intake (the grille between the bonnet and the windscreen). Fault tracing An authorised Volvo workshop has the instru- ments and tools required for any fault tracing or repair of your climate control system. Entrust checks and repairs only to trained personnel. Refrigerant The air conditioning system contains R134a refrigerant. This refrigerant contains no chlorine, which means that it is harmless to the ozone layer. The system must only be charged with R134a refrigerant. Have an authorised Volvo workshop carry out this work.
Ventilation fan function When the engine is off (and if the ignition key is in position I or II), the ventilation fan is automatically switched off. This is to prevent the battery from becoming discharged. To activate the ventilation fan, turn the fan control and set the desired speed. Cars with ECC Actual temperature The temperature you select corresponds to the physical experience with reference to air speed, humidity, exposure to sun, etc. which affect the interior and exterior of the car. Sensors The sun sensor is on the upper portion of the dashboard. Remember not to cover it. Do not cover the passenger compartment temper- ature sensor on the climate control panel. Side windows and sunroof To ensure that the air conditioning works satisfactorily, close all side windows and the sunroof (if fitted). Acceleration The air conditioning system switches off temporarily at full acceleration. You may feel a temporary rise in temperature.
68
General information on climate control
Climate control
Air distribution Incoming air is distributed through several different vents located throughout the car.
Air vents in the dashboard A. Open B. Closed C. Lateral airflow D. Vertical airflow – Aim the outer vents towards the side
windows to remove misting.
– In cold climates: close the centre vents
for the most comfortable climate and best demisting.
Air vents in the door pillars A. Open B. Closed C. Lateral airflow D. Vertical airflow – Aim the vents towards the windows to
remove misting from the rear side windows.
– Aim the vents inwards into the car for a
comfortable climate in the rear seat. Bear in mind that small children can be sensitive to airflow and draughts.
69
Climate control
Manual climate control, A/C
1. A/C – ON/OFF 2. Recirculation 3. Air distribution 4. Rear window and door mirror defroster 5. Heated front seats 6. Heating/Cooling right-hand side 7. Heating/Cooling, left-hand side 8. Fan
70
You must turn the fan knob (8) from the 0
position to connect the air conditioning. Use the air conditioning at low temperatures too (0–15 °C) in order to dehumidify incoming air. 1. A/C – ON/OFF The air conditioning is connected to the cooling and dehumidification function with the ON LED lights. The air conditioning is disconnected with the OFF LED lights. 2. Recirculation Recirculation can be used to shut out bad air, exhaust, etc. from the passenger compartment. The air in the passengercompartment is then recirculated, i.e. no air from outside the car is taken into the car when this function is activated. Recirculation (together with the air conditioning system) cools the passenger compartment more quickly in a warm climate. If you allow the air in the car to recirculate, there is a risk of icing and misting, especially in winter. The timer function minimises the risk of ice, misting and bad air. Activate the function as follows:
– Press
for more than 3 seconds. The LED flashes for 5 seconds. The air recirculates in the car for 3 – 12 minutes depending on the outside temperature.
Manual climate control, A/C – The timer function is activated each time
you press
To switch off the timer function:
– Press
again for more than
3 seconds. The LED lights for 5 seconds to confirm your selection.
3. Air distribution Use the air distribution control positions (marked with dots) between the different symbols to fine-tune air distribution for maximum comfort. Defroster
on the air distribution
The defroster control is used to quickly remove misting and ice from the windscreen and side windows. Air flows to the windows at high speed. When the function is selected the following also takes place to provide maximum dehumidification of the air in the passenger compartment: (cid:127)
the air conditioning (A/C) is automatically engaged (if the fan is not in position 0) recirculation is automatically disengaged.
(cid:127)
When the defroster climate control returns to the previous settings.
is switched off the
4. Rear window and door mirror defroster Use this button to quickly remove misting and ice from the rear window and door mirrors, see page 51 for further information about this function. 5. Heated front seats Do as follows for heated front seat(s): – Press once: High heat – both LEDs in the
switch light up.
– Press twice: Low heat – one LED in the
switch lights up.
– Press yet again: Heating is switched off –
no LEDs in the switch are lit.
An authorised Volvo workshop can adjust the temperature. 6. and 7. Heating/Cooling – left/ right-hand side Turn to set how warm or cold the incoming air should be. For cooler air, the air conditioning must be connected. 8. Fan Fan speed can be increased or decreased by turning the knob. If the knob is set to 0 then the air conditioning is not engaged.
Climate control
71
Air distribution Air to floor and air vents.
Use In sunny weather with cool outside temperatures.
Climate control
Manual climate control, A/C
Use When you want good cooling in a warm climate.
When you want to remove ice and misting. High fan speed is good for this.
When you want comfortable condi- tions and good demisting in a cold climate. Not too low a fan speed. When you want to warm your feet.
Air distribution
Air through front and rear air vents. Air to windows. Air is not
recirculated in this position. The air conditioning is always connected. There is a certain amount of airflow to the air vents.
Air to both floor and windows. There is a certain amount of airflow to the air vents.
Air to floor. There is a certain
amount of airflow to the air vents and the defroster vents for the windscreen and side windows.
72
Electronic Climate Control, ECC
Climate control
12
10
11
13
1. A/C – ON/OFF 2. Recirculation/Multifilter with sensor 3. Recirculation 4. AUTO 5. Air distribution 6. Passenger compartment temperature
sensor
7. Defroster, windscreen and side
windows
8. Rear window and door mirror defroster 9. Heated front seats 10. Temperature, right-hand side 11. Temperature, left-hand side 12. Fan 13. Fan, rear passenger compartment
(option in cars seating seven)
1. A/C – ON/OFF The air conditioning system is controlled automatically by the system when the ON LED is lit. This way, incoming air is cooled and dehumidified sufficiently. When A/C OFF is selected and the OFF LED comes on, the air conditioning system is always discon- nected; other functions are still controlled automatically. The air conditioning system operates down to approximately 0 °C. 2. Air quality system (option in certain markets) Certain cars are equipped with a "Multifilter" and air quality sensor. The Multifilter separates gases and particles, thus reducing the volume of odours and pollu tants. The air
quality sensor detects increased levels of contaminants in the outside air. When the air quality sensor detects contaminated outside air, the air intake is closed and the air in the passenger compartment is recirculated. The Multifilter also cleans the air recirculating in the passenger compartment. When the air quality sensor is active, the green AUT LED lights in
Operation
Press sensor (normal setting).
to activate the air quality
73
Climate control
Electronic Climate Control, ECC Or: Select one of the following three functions by pressing
repeatedly.
(cid:127) MAN LED lit: Recirculation is now
activated.
(cid:127) No LED lit: Recirculation is not activated unless needed to cool in a warm climate. (cid:127) AUT LED lit: The air quality sensor is now
activated.
Keep in mind the following: (cid:127) Make it a rule to have the air quality
sensor activated at all times.
(cid:127) Recirculation is limited in cold weather to
(cid:127)
(cid:127)
avoid misting. If misting occurs, you should deactivate the air quality sensor. If misting occurs, you can use the defroster functions for the windscreen, side windows and rear window.
(cid:127) Follow the Volvo Service Programme for
the recommended replacement interval of the Multifilter. If the car is used in a severely contaminated environment, it may be necessary to change the Multi- filter more often.
74
3. Recirculation Recirculation can be used to shut out bad air, exhaust, etc. from the passenger compartment. The air in the passenger compartment is then recirculated, i.e. no air from outside the car is taken into the car when this function is activated. If you allow the air in the car to recirculate, there is a risk of icing and misting, especially in winter. The timer function (cars with Multifilter and air quality sensor have no timer function) minimises the risk for ice, misting and bad air. Activate the function as follows:
– Press
for more than 3 seconds. The LED flashes for 5 seconds. The air recirculates in the car for 3 – 12 minutes depending on the outside temperature. – The timer function is activated each time
you press
To switch off the timer function:
– Press
again for more than
3 seconds. The LED lights for 5 seconds to confirm your selection.
4. AUTO AUTO function automatically regulates climate control so that the desired temper- ature is attained. The automatic function controls heating, air conditioning, air quality sensor, fan speed, recirculation, and air distribution. If you select one or more functions manually, the other functions continue operating automatically. All manual settings are switched off when AUTO is pressed. 5. Air distribution (cid:127) When the top button is depressed, air is
directed to the windows.
(cid:127) When the centre button is depressed, air
is directed to the head and body.
(cid:127) When the lower button is depressed, air
is directed to the legs and feet.
Press AUTO to return to automatic air distri- bution. 6. Passenger compartment temperature sensor The passenger compartment temperature sensor monitors the temperature inside the car.
Electronic Climate Control, ECC 7. Defroster, windscreen and side windows Used to quickly remove misting and ice from the windscreen and side windows. Air flows to the windows at high speed. The LED in the defroster button comes on when this function is engaged. When the function is selected the following also takes place to provide maximum dehumidification of the air in the passenger compartment: (cid:127)
the air conditioning (A/C) is automatically engaged (if the fan knob is in final anticlockwise position then the air condi- tioning is not engaged). recirculation is automatically disengaged.
(cid:127)
is switched off the
When the defroster climate control returns to the previous settings. 8. Rear window and door mirror defrosters Use this button to quickly remove misting and ice from the rear window and door mirrors, see page 51 for further information about this function.
9. Heated front seats Do as follows for heated front seat(s): (cid:127) Press once: high heat – both LEDs in the
switch light up.
(cid:127) Press twice: low heat – one LED in the
switch lights up.
(cid:127) Press yet again: Heating is switched off –
no LED in the switch is lit.
An authorised Volvo workshop can adjust the temperature. 10 and 11. Temperature The two knobs can be used to set the temperature for the passenger and driver’s sides of the car. Remember that the car does not heat up or cool down any more quickly even if you select a higher or lower temper- ature than you want in the passenger compartment. 12. Fan Fan speed can be increased or decreased by turning the knob. If AUTO is selected, fan speed is controlled automatically. The previ- ously set fan speed is disconnected. If the knob for the fan is turned so far to the left that only the left LED above the knob lights with an orange glow, the fan and air conditioning are switched off.
Climate control
13. Fan, rear passenger compartment (option in cars seating seven) Fan speed can be increased or decreased by turning the knob. This only applies if A/C is selected for both front (1) and rear passenger compartment. The button for rear passenger compartment is in the centre console switch panel, see page 49.
75
Climate control
Parking heater (option)
turning on the ignition.
General The electrical system must be "awakened" before the parking heater can be programmed. This is most easily done by: (cid:127) pressing the READ button or (cid:127) pressing the main beam flash or (cid:127) The parking heater can be started immedi- ately or set with two different start times using TIMER 1 and TIMER 2. Start time refers to the time the car should be heated and ready. The car’s electronic system calculates when heating should be started based on the 76
outside temperature. If the outside temper- ature exceeds 25 °C, the heater does not switch on. At temperatures of –10 °C and below, the maximum running time of the parking heater is 60 minutes. If the parking heater does not start despite repeated attempts, a message is shown on the display. Contact an authorised Volvo workshop.
WARNING!
(cid:127) Switch off the fuel-driven heater before refuelling. Spilled fuel could be ignited by the exhaust gases. (cid:127) Check on the information display that the heater is off. (When the additional heater is running, PARK HEAT ON is shown on the display.)
WARNING!
The car must be outdoors when the petrol or diesel heater is used.
Warningdecalonfuelfillerflap. Messages on the display Once the settings for TIMER 1, TIMER 2 and Direct Start are activated, the amber warning symbol in the combined instrument panel comes on and explanatory text is shown on the display. When you leave the car, you will receive a message regarding the current settings of the system. Parking on a hill If you park your car on a steep incline, the front of the car should be facing up the slope to ensure the supply of fuel to the parking heater.
Parking heater (option) Car clock/timer For safety reasons, all timer settings will be cleared if the car clock is reset after timer settings have been made. Setting TIMER 1 and 2
For safety reasons, you can only programme times for the following 24 hours, not several days in advance. – Use the ring (B) to toggle to TIMER 1. – Briefly press the RESET button (C) sothat the hours setting starts to flash.
– Use the ring (B) to set the desired hours. – Briefly press the RESET button so that
the minutes setting starts to flash. – Use the ring (B) to set the desired
minutes.
– Briefly press the RESET button to confirm
your setting.
– Press the RESET button to activate the
timer.
After setting TIMER 1, toggle to TIMER 2. Settings are made the same way as for TIMER 1. Deactivating timer-started heating Do as follows to manually switch off the heater before the set time has elapsed: – Press the READ button (A).
– Use the ring (B) to toggle to PARK HEAT
TIMER 1 or 2. The text ON flashes.
– Press the RESET button (C). The text
OFF is displayed with a steady glow and the heater is switched off.
Direct start – Use the ring (B) to toggle to DIRECT
START.
– Press the RESET button (C) to access
the alternatives ON or OFF. Select ON.
The heater will now run for 60 minutes. Heating of the passenger compartment will begin as soon as the engine coolant has reached an adequate temperature. Deactivating heater after direct start – Use the ring (B) to toggle to DIRECT
START.
– Press the RESET button (C) to make ON
and OFF selections available.
– Select OFF. Battery and fuel If the battery is not sufficiently charged or the petrol tank is close to empty, the parking heater will be switched off. If this is the case, you will receive a message in the display. Confirm the message using the READ button (A).
Climate control
IMPORTANT! Repeated use of the parking heater in combination with short trips can lead to battery discharge and thereby difficulty starting. If the heater is used regularly, the car should be driven for the same amount of time as the heater was used in order to ensure that the generator is able to produce enough energy to compensate for the amount consumed.
Additional heater (diesel) (certain countries) Extra heat from the additional heater may be required in cold weather to reach the correct temperature in the passenger compartment. The additional heater starts automatically when extra heat is required if the engine is running. It is switched off automatically when the correct temperature is reached or when the engine is switched off.
77
Climate control
78
Front seats Interior lighting Storage spaces in the passenger compartment Rear seat Cargo compartment
Interior 80
83
85
90
9279
Interior
Front seats
WARNING!
Adjust the position of the driver’s seat before setting off, never while driving. Check that the seat is locked in position.
Seating position The driver’s and passenger seats can be adjusted to the optimum sitting and driving positions. 1. Forward/rearward: lift the handle to adjust the distance to the steering wheel and pedals. Check that the seat is locked after changing position
2. Raise/lower front edge of seat cushion:
pump up/down
Lumbar support: turn the wheel
3. Raise/lower seat: pump up/down 4. 5. Backrest rake: turn the wheel 6. Power seat control panel.
80
Lowering the front seat backrest The front passenger seat backrest can be folded to a horizontal position to make room for a long load. Fold the backrest as follows: – Move the seat as far back as possible. – Adjust the backrest to the upright
position.
– Lift the catches on the rear of the
backrest.
– Fold the backrest forward. – Slide the seat forward so that the head restraint is "locked in place" under the glovebox.
Front seats Power seat (option) Preparations The seat is normally adjusted with the ignition key is in position I or II. It can also be adjusted within 4,5 minutes of the door being unlocked with the key or remote control. If the door is closed and the ignition key is not yet in the ignition, or is in the 0 position, adjust- ments can be made within 40 seconds of the door being closed. Memory function in the remote control (option) The remote control used to unlock the car stores information about the changes made to the seat settings. When the car is next unlocked with the same remote control and the door is opened within five minutes, the driver’s seat and the door mirrors assume the stored positions.
Interior
Seat adjustment The switches can be used to make the following adjustments: 1. Front edge of seat cushion up/down 2. Seat forward/rearward 3. Seat up/down 4. Backrest rake The seat can be moved in one direction at a time. The power seats have an overload protector that activates if a seat is blocked by an object. If this occurs, switch off the ignition (position 0) and wait 20 seconds before operating the seat again.
Seat with memory function 5. Setting seat and door mirrors,
program 1
6. Setting seat and door mirrors,
program 2
7. Setting seat and door mirrors,
program 3
8. Storing preset positions Three positions can be stored. After adjusting the seat, hold the MEM (8) button depressed while pressing the button (5). Further seat and door mirror settings can be stored using memory buttons (6) and (7).
81
Interior
Front seats Setting preset positions Press and hold one of the memory buttons (5), (6) or (7) until the seat stops. If you release the button, the seat stops immediately for safety reasons. Emergency stop If the seat accidentally begins to move, press one of the buttons to stop the seat.
WARNING!
Ensure that there is nothing in front of, behind, or under the seat during adjustment. Ensure that none of the backseat passengers will be trapped. To avoid injury, ensure that children do not play with the switches.
82
Interior lighting
Interior
(cid:127) stop the engine and turn the ignition key
to position 0.
General lighting lights up and remains lit for 10 minutes when: (cid:127) one of the doors is open (cid:127) unless general lighting is switched off. General lighting switches off: (cid:127) (cid:127)
the engine is started you lock the car from outside using the key or remote control.
General lighting can be switched on or off in all situations by briefly pressing the button. Unless switched off manually, general lighting goes out automatically 10 minutes after the engine is switched off. You can switch off the timer by pressing the button for more than 3 seconds. When you then briefly press the button again, the timer reconnects. The pre-programmed times of 30 seconds and 10 minutes can be modified. Contact an authorised Volvo workshop.
General lighting General lighting is activated and deactivated by pressing the centre button. A brief press on this button will switch general lighting on or off in any situation. Activate and deactivate general lighting by pressing the centre button. General lighting comes on automati- cally1 and remains lit for either 30 seconds or 10 minutes when the engine is off. General lighting comes on and remains lit for 30 seconds when you: (cid:127) when you unlock the car from the outside
using the key or remote control
1.
The function is light-dependent and is only activated when it is dark.
Reading lamps Reading lamps can be switched on or off by pressing the respective button. For cars seating seven, both reading lamps for the third row of seats are switched on or off when one of the buttons is pressed. Unless switched off manually, reading lamps are switched off automatically 10 minutes after the ignition is switched off.
83
Interior
Interior lighting
Vanity mirror1
The light comes on automatically when the cover is lifted.Option on certain markets.
1. 84
Storage spaces in the passenger compartment
Interior
85
Interior
Storage spaces in the passenger compartment Storage spaces 1. Storage compartment in third row of
seats.
2. Storage compartment and cup holder. 3. Ticket clip. 4. Glovebox. 5. Storage tray in centre console. 6. Cup holder for rear seat passengers. 7. Storage pocket (also on front edge of
the front seat cushions).
8. Grocery bag holder.
WARNING!
Ensure that no hard, sharp or heavy objects lie or protrude in such a way that they could cause injury during heavy braking. Always secure large and heavy objects with a seatbelt or cargo retaining straps.
86
Pen holder The centre console contains a pen holder.
Glovebox The glovebox can be used to store things such as the Owner’s Manual, maps, pens and petrol cards. Floor mats (option) Volvo supplies floor mats specially manufac- tured for your car. These should be properly anchored with the clips on the floor so they do not slide and get jammed beside or under the driver’s pedals.
Storage spaces in the passenger compartment
Interior
Coat hanger The coat hanger is only intended for light garments.
Ashtray for rear seat passengers (option) Open the ashtray by pulling the top edge outward. To empty: – Open the ashtray. – Press the cover outwards and tip it back. – Then lift it out.
Cup/bottle holder for rear seat passengers Pull the bottom edge of the insert to open. The cup holder insert can be removed: Detach the two clips so the holder can be used for large bottles.
87
Interior
Storage spaces in the passenger compartment
Storage compartment and cup holder (cars seating seven) This storage compartment can be used for CDs, books and the like.
Storage tray in centre console The centre console contains a storage tray for food and drinks, for example. The armrest can be folded back to make a "table" for rear seat passengers. Under the storage tray is a storage compartment, e.g. for CD discs.
Cup holder Cup holder for front seat passengers. Ashtray (option) Pull out the insert to empty the astray.
88
Storage spaces in the passenger compartment
Storage compartment in the third row of seats (cars seating seven) This storage compartment can be used for pens and other small items.
Interior
89
Interior
Rear seat
Rear seats – second row (cars seating seven) Lowering the backrest for entry into the car Lift the handle (1) up while pushing the backrest forward. Do the reverse to return the seat to its original position. Adjusting the seat front - rear Lift the bracket (2) to move the seat front or back.
Sliding seat (cars seating seven) The centre seat in the second row can be slid farther forward than the other seats. Sliding the seat completely forward improves contact between a child sitting on the integrated booster cushion and front seat occupants. Lift the bracket (A) to move the seat front or back.
Removing the rear section of the centre console The centre console must first be removed if you wish to slide the centre seat in the second row forward. – Remove the rear section of the centre
console by pulling the catch straight out as illustrated above.
– Then lift the console out of the way.
90
Rear seat
WARNING!
The lowest position should only be used when the backrest is to be folded down or when no one is sitting in this seat. After raising the backrests in the second and third row, it is important to make sure that the backrests have locked into position. Otherwise the protective system of the seats may be compromised.
Head restraint, rear seat – centre seat The centre seat head restraint can be adjusted to four different heights. Slide the head restraint up as desired. Press in the release button to lower it. See illustration! Note that the head restraint cannot be removed completely!
Interior
91
Interior
Cargo compartment
Repositioning the seats in the third row – Raise the backrest to its normal position. – Take hold of the eyes and pull out the seat
cushion until you hear a click.
– Raise the head restraint.
