However, as with any other radial tires, if rotated, the tires must be kept on the same side of the car so that they revolve in the same direction as before rotation.
Volvo recommends 195/65 R15 snow tires on non-turbo models. Turbo models should be equipped with 205/55
R16 snow tires on all four wheels (215/65 R16 tires should be used on the XC70).
Winter tires wear more quickly on dry roads in warm weather. They should be removed when the winter driving season has ended.
Studded tires should be run-in 300-600 miles (500-1000 km) during which the car should be driven as smoothly as possible to give the studs the opportunity to seat properly in the tires. The tires should have the same rotational direction throughout their entire lifetime. In other words, if you wish to rotate the wheels, make sure that the same wheels are always on the same side of the car.
NOTE: Please consult state or provincial regulations restricting the use of studded winter tires before installing such tires.
* Where permitted.
pg. 110 Wheels and tires
Checking and correcting tire pressure
Tire pressure label
Check the tire pressure regularly. The tire pressure should be corrected only when the tires are cold. With warm tires, correct only when the pressure is too low. The tire temperature rises after driving just a few miles.
Vehicle loading
The tires on your Volvo will perform to specifications at all normal loads when inflated as recommended on the tire information label located on the inside of the fuel filler door*. This label also lists vehicle load limits. Do not load your car beyond the indicated limits.
WARNING! Improperly inflated tires will reduce tire life, adversely affect vehicle handling and can possibly lead to failure resulting in loss of vehicle control without prior warning.
Temporary Spare
The spare tire in your car is called a "Temporary Spare". It has the following designation: T125/80 R17 (T135/90 R17
on the XC70).
At the recommended tire pressure shown on the inside of the fuel filler door, the tire may be used as a temporary replacement for a front or rear tire.
In the event of damage to this tire, a new one can be purchased from your Volvo retailer.
WARNING! Current legislation prohibits the use of the "Temporary Spare" tire other than as a temporary replacement for a punctured tire. It must be replaced as soon as possible by a standard tire. Road holding and handling may be affected with the "Temporary Spare" in use. Do not exceed 50 mph (80 km/h). Do not drive farther than 50 miles (80 km) on a temporary spare tire.
CAUTION: The car must not be driven with wheels of different dimensions or with a spare tire other than the one that came with the car. The use of different size wheels can seriously damage your car's transmission.
NOTE: Certain models may be equipped with a full-size spare tire. When used, it should be inflated to the same pressure as the tire it is replacing.
*Please note that the tire information label indicates pressure for both comfort and fuel economy.
pg. 111 Wheels and tires
Uniform tire quality grading
ALL PASSENGER CAR TIRES MUST CONFORM TO FEDERAL SAFETY REQUIREMENTS IN ADDITION TO THESE GRADES
Quality grades can be found, where applicable, on the tire sidewall between the tread shoulder and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
TREADWEAR
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions
on a specified government test course. For example, a tire graded 150 would wear one and one half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and many depart significantly from the norm due to variation in driving habits, service practices and differences in road characteristics and climate.
TRACTION
The traction grades, from highest to lowest, are AA, A, B, and C, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
WARNING! The traction grade assigned to this tire is based on braking (straight-ahead) traction tests and is not a measure of cornering (turning) traction.
TEMPERATURE
The temperature grades are AA (the highest), A, B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a minimum level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
pg. 112 Changing wheels
Insert flat end of lug wrench and turn/pull straight out
Changing wheels
The spare wheel is located under the carpet on the cargo area floor. The jack and crank are secured in the wheel recess. There are two jack attachment points on each side of the car.
To change a wheel:
Engage the parking brake. Put the gear selector in (P)ark. Remove the wheel cap (where applicable) using the lug wrench in the tool kit. With the car still on the ground, use the lug wrench to loosen the wheel bolts 1/2 - 1 turn by exerting downward
pressure. Turn the bolts counterclockwise to loosen.
Loosen wheel bolts
Position the jack on the bar in the attachment (A in the illustration in right column) and crank while simultaneously guiding the base of the jack to the ground. The base of the jack must be flat on a level, firm, non-slippery surface. Before raising the car, check that the jack is still correctly positioned in the attachment.
Raise the vehicle until the wheel to be changed is lifted off the ground. Unscrew the wheel bolts completely and carefully remove the wheel so as not to damage the thread on the studs.
NOTE: See also page 133 for hoisting the vehicle on a garage lift!
WARNING!
The jack must correctly engage the bar in the jack attachment (A). The car's weight must not rest on the jack
attachment (B). See illustration on page 113.
Be sure the jack is on a firm, level, non-slippery surface. Never allow any part of your body to be extended under a car supported by a jack. Use the jack intended for the car when replacing a wheel. For any other job, use stands to support the side of the
car being worked on.
Apply the parking brake and put the gear selector in the (P)ark position. Block the wheels standing on the ground, use rigid wooden blocks.
pg. 113 Wheels and tires
Attaching the jack
NOTE: To avoid excessive wear and the necessity of rebalancing, mark and reinstall wheels in the same location and position as before removal. To lessen the chance of imbalance, each wheel hub is equipped with a guide stud to ensure that a removed wheel can be reinstalled in its original position (as when changing over to winter tires/wheels).
NOTE: Refer to page 133 for hoisting the vehicle on a garage lift.
CAUTION:
Jack for AWD models
The car must not be driven with wheels of different dimensions or with a spare tire other than the one that came with
the car. The use of different size wheels can seriously damage your car's transmission.
Correct tightening torque on wheel bolts must be observed. The wheel bolts should never be greased or lubricated. The extended, chromed wheel bolts must not be used with steel rims, as they make it impossible to fit the hub caps.
Installing the wheel
Correct tightening order for wheel bolts
Clean the contact surfaces on the wheel and hub. Lift the wheel and place it on the hub. Make sure that you align the wheel with the guide stud on the wheel hub prior
Install the wheel bolts and tighten hand-tight. Using the lug wrench, tighten crosswise (see illustration above) until
to installation.
all bolts are snug.
Lower the vehicle to the ground and alternately tighten the bolts crosswise to 100 ft. lbs. (136 Nm). Install the wheel cap (where applicable).
Contents | Top of Page
2 0 0 3 VOLVO
V70
HomeLink® Universal Transceiver (option)
pg. 167 HomeLink® Universal Transceiver (option)
HomeLink® Universal Transceiver
HomeLink® is an advanced system that can be programmed to learn the codes of three different remote controlled- devices (e.g., garage door openers, remote lighting, entry door lock). HomeLink®'s sun visor-mounted transceiver, powered by your car's electrical system, may then be used in place of your hand-held remote controls.
NOTE: For your security, the HomeLink® Universal Transceiver is designed to not function if you lock your car from the outside.
Programming the transceiver
1. The ignition switch must be turned to the "accessory" position (II) before programming the HomeLink® Universal Transceiver.
2. Begin by erasing all 3 factory default channels. Hold down the two outside buttons (buttons 1 and 3 in the illustration) on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink®'s indicator light begins to flash. Then release the buttons.
3. Hold your hand-held transmitter (garage door opener, for example) 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface, keeping the indicator light in view. For placement questions, contact HomeLink® toll-free 1- 800-355-3515 (Internet: www.HomeLink.com).
4. Using two hands, push and hold both your hand-held transmitter's button and the transceiver button you wish to program. The indicator light will flash first slowly, then rapidly. Rapid flashing tells you the HomeLink® button has
been successfully programmed. Release both buttons.
5. If you are programming a rolling code-equipped device (e.g., garage door opener or entry door lock), refer to "Programming rolling codes" on the next page to complete the programming process.
Repeat steps 3 and 4 to program the other two transceiver buttons.
If, after several attempts, you are unable to successfully train the HomeLink® Universal Transceiver to learn your hand-held transmitter's signal, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
WARNING!
If you use HomeLink® to open a garage door or gate, be sure no one is near the gate or door while it is in motion. Do not use the HomeLink® Universal Transceiver with any garage door opener that lacks safety "stop" and
"reverse" features as required by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982) A garage door opener that cannot "detect" an object, signalling the door to "stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355- 3515 (Internet: www.HomeLink.com).
pg. 168 HomeLink® Universal Transceiver (option)
NOTE - Canadian residents: During programming, your hand-held transmitter may automatically stop transmitting. To successfully train HomeLink®, continue to hold the HomeLink® button. At the same time, repeatedly press and hold your hand-held transmitter's button at two-second intervals until HomeLink® has learned your transmitter's code. The HomeLink® indicator light will flash first slowly, and then rapidly to indicate that the button has been successfully programmed.
Determining if your garage door uses a rolling code Determine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after 1996:
Refer to the garage door opener owner's manual for verification. If your hand-held transmitter appears to program the HomeLink® Universal Transceiver but the programmed button
does not activate the garage door, your garage door opener may have a rolling code.
Press the programmed HomeLink® button. If the garage door opener has the rolling code feature, the HomeLink®
indicator light flashes rapidly and then glows steadily after approximately 2 seconds.
To train a rolling code garage door opener, follow these instructions after programming the desired transceiver button according to "Programming the transceiver." The help of a second person may make training easier.
1. Locate the training button on the garage door opener motor head unit. The location and color of the training button
may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call toll-free 1-800-355-3515
(Internet: www.HomeLink.com).
2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.
3. Press and release the programmed HomeLink® button. Press and release the programmed HomeLink® button a second time to complete the training process. Some garage door openers may require you to do this procedure a third time to complete the training.
The programmed button on your HomeLink® Universal Transceiver should now operate your garage door opener. The
original hand-held transmitter can also be used, as desired, to operate the garage door.
The remaining two HomeLink® buttons can be programmed in the same way. In the event of any problems in programming the HomeLink® Universal Transceiver, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
Operating the HomeLink® Universal Transceiver Once programmed, the HomeLink® Universal Transceiver can be used in place of your hand-held transmitters.
To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press the programmed HomeLink® button to activate the garage door, driveway gate, security lighting, home security system, etc.
Your original hand-held transmitters may, of course, be used at any time.
Erasing programmed buttons Individual buttons cannot be erased. To erase all three programmed buttons:
1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink®'s indicator light begins to flash.
3. Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures described on the previous page.
(HomeLink® information continues on the next page)
pg. 169 HomeLink® Universal Transceiver (option)
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position your hand-held transmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.
3. Press and hold the hand-held transmitter button. The HomeLink® indicator light will flash first slowly, then rapidly. When the indicator light flashes rapidly, release both buttons.
The previously programmed device has now been erased and the new device can be activated by pressing the HomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink® buttons.
NOTE:
Retain the original transmitter(s) for future programming procedures (e.g., if you purchase a new car). For your own security, erase all programmed buttons on the HomeLink® Universal Transceiver when you sell your
car.
Metallic sun protection films should not be used on any windows in a car equipped with HomeLink® Universal
Transceiver. This could interfere with the transceiver's function.
Contents | Top of Page
2 0 0 3 VOLVO
V70
Chapter 8 - Maintenance/Servicing
pg. 115 Maintenance/Servicing
Fuses 116
Replacing bulbs 120
Paint touch up 126
Washing the car 127
Cleaning the upholstery 128
Maintenance service, Warranty 129
Fuel/emissions systems 130
Drive belt, Air pump system, Coolant 131
Emissions maintenance 132
Washer fluid reservoir, Hoisting the car 133
Opening the hood, Engine compartment 134
Engine oil 135
Power steering/Brake fluid reservoirs 137
Battery maintenance 138
Replacing wiper blades 140
pg. 116 Fuses
Replacing fuses
If an electrical component fails to function, it is possible that a fuse has blown due to a temporary circuit overload.
Fuses are located in different places:
A - Relays/fuse box in the engine compartment B - Fuse box in the passenger compartment C - Relays/fuse box in the cargo area
A label on the inside of each cover indicates the amperage and the electrical components that are connected to each fuse.
The easiest way to see if a fuse is blown is to remove it. Pull the fuse straight out. If a fuse is difficult to remove, you will find a special fuse removal tool in the passenger compartment fuse box. From the side, examine the curved metal wire to see if it is broken. If so, put in a new fuse of the same color and amperage (written on the fuse). Spare fuses are stored in the fuse box in the passenger compartment. If fuses burn out repeatedly, have the electrical system inspected by an authorized Volvo retailer.
WARNING! Never use fuses with higher amperage that those stated on the following pages. Doing so could overload the car's electrical system.
pg. 117 Fuses in the engine compartment
Relays/fuses in the engine compartment
When replacing fuses, be sure to replace a blown fuse with a new one of the same color and amperage (written on the fuse). Fuse amperage is also indicated on the inside of the fuse box cover.
A - To open, press the plastic catches on the rear side of the fuse box cover and lift
Ordinary fuses
Amperage 25A 20A 15A 20A 10A 15A 10A 10A 15A 10A 20A 5A 25A 30A
Location 1 Accessories 2 Auxiliary lamps (option) 3 Vacuum pump 4 Oxygen sensors 5 Crankcase ventilation heater, solenoid valves 6 Mass airflow sensor, engine control module, injectors 7 Throttle module 8 AC compressor, accelerator pedal position sensor, E-box fan 9 Horn 10 Tailgate wiper 11 AC compressor, ignition coils 12 Brake light switch 13 Windshield wipers 14 ABS/STC/DSTC 15 - 16 Windshield washers, headlight wiper/washers (certain models) 15A 10A 17 Low beam, right 18 Low beam, left 10A 30A 19 ABS/STC/DSTC 15A 20 High beam, left 21 High beam, right 15A 25A 22 Starter motor 23 Engine control module 5A 24 -
pg. 118 Fuses in the passenger compartment
Fuse box in the passenger compartment
This fuse box is located at the far left side of the instrument panel. Extra fuses and the fuse removal tool are also stored here. When replacing a blown fuse, be sure to replace it with a new one of the same color and amperage (written on the fuse).
Location 1 Low beam headlights 2 High beam headlights 3 Power driver's seat 4 Power passenger's seat 5 - 6 - 7 Heated seat - front left (option) 8 Heated seat - front right (option) 9 ABS/STC/DSTC 10 - 11 - 12 Headlight wipers (certain models) 13 Electric socket 12 V 14 Power passenger's seat 15 Audio system, VNS 16 Audio system 17 Audio amplifier 18 Front fog lights 19 VNS display 20 - 21 Automatic transmission, shiftlock, extended D2 feed 22 Direction indicators 23 Headlight switch module, climate control system, onboard diagnostic connector, steering wheel lever modules 24 Relay for extended D1 feed: climate control system, power driver's seat, driver's info 25 Ignition switch, relay starter motor, SRS, engine control module 26 Climate control system blower 27 - 28 Electronic module - courtesy lighting 29 - 30 Left front/rear parking lights 31 Right front/rear parking lights, license plate lights 32 Central electrical module, vanity mirror lighting, power steering, glove compartment light, interior courtesy lighting
Amperage 15A 20A 30A 30A
15A 15A 5A
15A 15A 5A 5A 20A 30A 15A 10A
10A 20A 5A 10A 10A 30A
10A
7.5A 7.5A 10A
33 Fuel pump 34 Power sun roof 35 Central locking system, power windows - left door mirror 36 Central locking system, power windows - right door mirror 37 Rear power windows, power child safety 38 Alarm siren
* Please be aware that if this fuse is not intact, or if it is removed, the alarm will sound.
15A 15A 25A 25A 30A 5A
pg. 119 Fuses in the cargo area
Fuses in the cargo area
The fuses in the cargo area are located on the trim on the left-hand side. When replacing a blown fuse, be sure to replace it with a new one of the same color and amperage (written on the fuse).
Ordinary fuses
Amperage Location 10A 1 Rear electrical module, cargo area lighting 10A 2 Rear fog light 15A 3 Brake lights 4 Backup lights 10A 5 Rear window defroster, relay 15I - accessories 5A 6 Unlocking tailgate 10A 7 Auxiliary 12 volt socket in cargo area (option) 15A 20A 8 Central locking rear doors/fuel filler door 15A 9 Trailer (30 feed) 10 CD changer, VNS 10A 15A 11 Accessory control module (AEM) 12 Tailgate wiper 15A 13 Loudspeaker (subwoofer) cargo area - option 15A 7.5A 14 Brake lights 15 Trailer (15I feed) 20A 16 - 17 All Wheel Drive control module
7.5A
18 -
pg. 120 Replacing bulbs
Replacing high/low beam headlight bulbs
The headlight bulbs must be replaced from the engine compartment.
CAUTION:
Do not touch the glass on halogen bulbs with your fingers. Grease, oil or any other impurities can be carbonized onto
the bulb and cause damage to the reflector.
Be sure to use bulbs of the correct type and voltage.
To remove a defective low beam bulb:
Removing a defective bulb
Switch off all lights and turn the ignition switch to position 0. Open the hood. Remove the plastic cover over the bulb (1) by turning it counterclockwise. Remove the connector (2). Loosen the retaining spring (3) by first moving it to the right and then moving it down, out of the way. Pull out the defective bulb. Note the position of the guide lug on the base of the bulb (4).
To install a new low beam bulb (H7):
Installing a new bulb
Insert the new bulb, without touching the glass, with the guide lug upward (1). The bulb will only seat properly in
this position.
Move the retaining spring up and push it slightly to the left until it seats properly (2). Press the connector into place on the bulb (3). Reinstall the plastic cover and turn it clockwise until it is correctly in place (4). "TOP" must be upward.
NOTE: If the vertical aim of your headlights needs to be adjusted for any reason (e.g., towing a trailer for extended periods), this should be done by an authorized Volvo retailer.
pg. 121 Replacing bulbs
To remove and install a high beam bulb (HB3):
Switch off all lights and turn the ignition switch to position 0. Open the hood. Remove the cover by twisting it counterclockwise. Twist the bulb holder counterclockwise, pull it out and fit a new bulb. Note its position. Refit the bulb holder. It can only be fitted in one way. Screw the cover back on. The word TOP should be upwards.
Replacement of front parking light bulb
Switch off all lights and turn ignition key to position 0. Remove the low beam cover by twisting counterclockwise. Pull out the bulb and its socket. Replace bulb. Press the bulb and its socket back into place. Check that the new bulb lights. Screw the cover back into place, "TOP" should be upwards!
Changing the bulb in the turn signals at the front corners
Switch off all lights and turn ignition key to position 0. Pull out the bulb and its socket by twisting counterclockwise. Replace bulb. Press the bulb and its socket back into place. Check that the new bulb lights.
pg. 122 Replacing bulbs
Replacement of bulbs in backup light, rear parking lights and rear fog lights
Switch off all lights and turn the ignition switch to position 0. Open the access panel. Remove the sound insulation behind it. Twist the bulb holder counterclockwise and remove it. Press the bulb inward, twist it counterclockwise and extract it. Fit a new bulb. Fit the bulb holder in place and twist it clockwise.
Refit the sound insulation and put the access panel back in place.
Replacement of rear turn signal and brake light bulbs
Switch off all lights and turn the ignition switch to position 0. Using a screwdriver, carefully pry off the speaker grille. Pull out the red tab in the speaker. Then press on the black pin above the extracted red tab and twist out the speaker. Twist the bulb holder counter-clockwise, and withdraw it. Fit a new bulb. Fit the bulb holder in place and twist it clockwise. Refit the speaker and press in the red tab. Press the speaker grille back into position.
pg. 123 Replacing bulbs
Front fog lights (option)
CAUTION: Avoid touching the glass on the bulb with your fingers.
Switch off all lights and turn the ignition key to position 0. Turn the bulb holder slightly counterclockwise to release it. Replace the bulb. The shape of the base of the bulb corresponds to the shape of the bulb holder. Reinstall the bulb holder by turning it slightly clockwise. "TOP" on the holder should be upward.
Side direction indicator
Open the front door halfway. From the inside of the fender, push the lamp housing out. Turn the bulb holder 1/4 turn counterclockwise and pull it out from the lens. Remove the defective bulb by pulling it straight out. Insert a new bulb. Reinsert the bulb holder in the lens and press the entire unit back into place on the fender.
Door step courtesy lights
The door step courtesy lights are located under the dash on the driver's and passenger's sides. To replace a bulb:
Carefully insert a screwdriver and pry out the lens. Replace the defective bulb. Reinstall the lens.
pg. 124 Replacing bulbs
License plate lights
Switch off the ignition. Loosen the screws with a Torx screwdriver. Carefully pull out the lamp housing. Turn the bulb holder counterclockwise and pull it out. Pull out the defective bulb and insert a new one. Reinsert the bulb holder into the housing and turn it clockwise. Reinstall the housing and screw it in place.
Vanity mirror lights
Carefully insert a screwdriver and pry out the lens. Pry out the defective bulb and replace it. Carefully press the lower edge of lens onto the four tabs and press the upper edge of the lens into place.
Front courtesy lights
These bulbs may be difficult for you to replace yourself. We recommend that you let an authorized Volvo retailer replace these bulbs if necessary.
pg. 125 Replacing bulbs
Rear reading lights
These bulbs may be difficult for you to replace yourself. We recommend that you let an authorized Volvo retailer replace these bulbs if necessary.
NOTE: Other bulbs may be difficult for you to replace yourself. Let an authorized Volvo retailer replace these bulbs if necessary.
pg. 126 Paint touch up
Paint touch-up
Paint damage requires immediate attention to avoid rusting. Make it a habit to check the finish regularly - when washing the car for instance. Touch-up if necessary.
Paint repairs require special equipment and skill. Contact your Volvo retailer for any extensive damage.
Minor scratches can be repaired by using Volvo touch-up paint.
NOTE: When ordering touch-up paint from your Volvo retailer, use the paint code indicated on the model plate. The plate is located in the engine compartment.
Minor stone chips and scratches
Material: Primer - can Paint - touch-up bottle Brush
Masking tape
NOTE: When touching up the car, it should be clean and dry. The surface temperature should be above 60° F (15° C). Minor scratches on the surface
If the stone chip has not penetrated down to the metal and an undamaged layer of paint remains, the touch-up paint can be applied as soon as the spot has been cleaned.
Deep scratches
1. Place a strip of masking tape over the damaged surface. Pull the tape off so that any loose flakes of paint adhere to it.
2. Thoroughly mix the primer and apply it with a small brush. When the primer surface is dry, the paint can be applied using a brush. Mix the paint thoroughly; apply several thin paint coats and let dry after each application.
3. If there is a longer scratch, you may want to protect surrounding paint by masking it off.
pg. 127 Washing the car
Washing the car
The car should be washed at regular intervals since dirt, dust, insects and tar spots adhere to the paint and may cause
damage. It is particularly important to wash the car frequently in the wintertime to prevent corrosion, when salt has been used on the roads.
When washing the car, do not expose it to direct sunlight. Use lukewarm water to soften the dirt before you wash
with a sponge and plenty of water, to avoid scratching.
Bird droppings: Remove from paintwork as soon as possible. Otherwise the finish may be permanently damaged. A detergent can be used to facilitate the softening of dirt and oil. A water-soluble grease solvent may be used in cases of sticky dirt. However, use a wash place equipped with a
drainage separator.
Remove dirt from the drain holes in the doors and rocker panels. Dry the car with a clean chamois. Tar spots can be removed with kerosene or tar remover after the car has been washed. A stiff-bristle brush and lukewarm soapy water can be used to clean the wiper blades. Frequent cleaning improves
visibility considerably.
Wash off the dirt from the underside (wheel housings, fenders, etc.). In areas of high industrial fallout, more frequent washing is recommended.
CAUTION: During high pressure washing, the spray mouthpiece must never be closer to the vehicle than 13" (30 cm). Do not spray into the locks. Special sun roof cautions: - Always close the sun roof and sun shade before washing your vehicle. - Never use abrasive cleaning agents on the sun roof. - Never use wax on the rubber seals around the sun roof.
When washing or steam cleaning the engine, avoid spraying water or steam directly on the electrical components or
toward the rear side of the engine.
After cleaning the engine, the spark plug wells should be inspected for water and blown dry if necessary.
Suitable detergents: Special car washing detergents should be used. Mix according to manufacturer's instructions.
Bumpers: The bumpers are painted. Wash the bumpers with the same cleaning agent used on the rest of the car. Never clean the bumpers with gasoline or paint thinner. Difficult spots can be removed with denatured alcohol. To avoid scratches, do not dry the bumpers with paper.
WARNING!
When the car is driven immediately after being washed, apply the brakes several times in order to remove any
moisture from the brake linings.
Engine cleaning agents should not be used when the engine is warm. This constitutes a fire risk.
pg. 128 Washing the car, Cleaning the upholstery
Automatic washing - simple and quick
We do NOT recommend washing your car in an automatic wash during the first six months (because the
paint will not have hardened sufficiently).
An automatic wash is a simple and quick way to clean your car, but it is worth remembering that it may not be as
thorough as when you yourself go over the car with sponge and water. Keeping the underbody clean is most important, especially in the winter. Some automatic washers do not have facilities for washing the underbody.
Before driving into an automatic wash, make sure that side view mirrors, auxiliary lamps, etc, are secure, otherwise
there is risk of the machine dislodging them. Polishing and waxing
Normally, polishing is not required during the first year after delivery. However, waxing may be beneficial. Before applying polish or wax the car must be washed and dried. Tar spots can be removed with kerosene or tar
remover. Difficult spots may require a fine rubbing compound.
After polishing, use liquid or paste wax. Several commercially available products contain both polish and wax. Waxing alone does not substitute for polishing of a dull surface. A wide range of polymer-based car waxes can be purchased today. These waxes are easy to use and produce a long-
lasting, high-gloss finish that protects the bodywork against oxidation, road dirt and fading.
Do not polish or wax your car in direct sunlight (the surface of the car should not be warmer than 113° F (45° C).
Cleaning the upholstery
The fabric can be cleaned with soapy water or a detergent. For more difficult spots caused by oil, ice cream, shoe
polish, grease, etc., use a clothing/fabric stain remover.
The plastic in the upholstery can be cleaned with a soft cloth and mild soap solution. Leather upholstery/suede-like upholstery (alcanteraTM) can be cleaned with a soft cloth and mild soap solution.
For more difficult spots, Volvo offers a leather care kit.
Under no circumstances should gasoline, naphtha or similar cleaning agents be used on the plastic or the
leather since these can cause damage. Cleaning the seat belts
Clean only with lukewarm water and mild soap solution. Cleaning floor mats
The floor mats should be vacuumed or brushed clean regularly, especially during winter, when they should be taken out for drying. Spots on textile mats can be removed with a mild detergent. Stain removal
Take extra care when removing stains such as ink or lipstick since the coloring can spread. Use solvents sparingly. Too much solvent can damage the seat padding. Start from the outside of the stain and work toward the center.
pg. 129 Maintenance service, Warranty
Maintenance service
Volvo advises you to follow the service program outlined in the Warranty and Service Records Information booklet. This maintenance program contains inspections and services necessary for the proper function of your car. The maintenance services contain several checks which require special instruments and tools and therefore must be performed by a qualified technician. To keep your Volvo in top condition, specify time-tested and proven Genuine Volvo Parts and Accessories. The Federal Clean Air Act - U.S.
The Federal Clean Air Act requires vehicle manufacturers to furnish written instructions to the ultimate purchaser to assure the proper servicing and function of the components that control emissions. These services, which are listed in the "Warranty and Service Records Information booklet," are not covered by the warranty. You will be required to pay for labor and material used. Maintenance services
Your Volvo passed several major inspections before it was delivered to you, in accordance with Volvo specifications. The maintenance services outlined in the Warranty and Service Records Information booklet, many of which will positively affect your vehicle's emissions, should be performed as indicated. It is recommended that receipts for vehicle emission services be retained in case questions arise concerning maintenance.
Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 128 provides information about maintenance of emission-related components. Applicable warranties - U.S.
In accordance with applicable U.S. and Canadian regulations, the following list of warranties is provided.
New Car Limited Warranty Parts and Accessories Limited Warranty Corrosion Protection Limited Warranty Seat Belt and Supplemental Restraint Systems Limited Warranty Emission Design and Defect Warranty Emission Performance Warranty
These are the Federal warranties; other warranties are provided as required by state/provincial law. Refer to your separate Warranty and Service Records Information booklet for detailed information concerning each of the warranties.
Contents | Top of Page
2 0 0 3 VOLVO
V70
Chapter 9 - Specifications
pg. 141 Specifications
Label information 142
Dimensions and weights 143
Engine specifications 144
Transmission specifications 145
Oil/fluid specifications and volumes 146
Fuel system, Distributor ignition system, Suspension 147
Electrical system 148
Volvo On Call 149
pg. 142 Label information
1 Vehicle Emission Control Information Your Volvo is designed to meet all applicable emission standards, as evidenced by the certification label on the underside of the hood. For further information regarding these regulations, please consult your Volvo retailer.
2 Vacuum hose routing (underside of hood)
3 Loads and Tire Pressures (on inside of fuel filler door)
4 Model plate Vehicle Identification Number (VIN). Codes for color and upholstery, etc. The plate is located in the engine compartment, on the inside of the left front fender.
5 Vehicle Identification Number (VIN) * The VIN plate is located on the top left surface of the dashboard. The VIN is also stamped on the right hand door pillar.
6 Federal Motor Vehicle Safety Standards (FMVSS) specifications (USA) and Ministry of Transport (CMVSS) standards (Canada) Your Volvo is designed to meet all applicable safety standards, as evidenced by the certification label on the facing side of the driver's door. For further information regarding these regulations, please consult your Volvo retailer.
7 Child safety latch label
* The Vehicle Identification Number (VIN) should always be quoted in all correspondence concerning your vehicle with the retailer and when ordering parts.
All specifications are subject to change without prior notice.
pg. 143 Dimensions and weights
Dimensions
Length - 185.4 in. (471 cm), XC70 -186.2 (473 cm) Width - 71 in. (180 cm), XC70 - 73.2 in. (186 cm) Height - 57.5 in. (147 cm), V70 AWD - 58.7 in. (149 cm), XC70 - 61.5 in. 156 cm) Wheelbase - 108.5 in. (276 cm), XC70 - 108.8 in. (276 cm) Track, front - 61.5 in. (156 cm), XC70 - 63.4 in. (161 cm) Track, rear - 61.4 in. (156 cm), XC70 - 60.9 in. (155 cm) Turning circle (between curbs) - 35.8-39 ft. (10.9-11.9 m) Cargo capacity - 17.1 cu. ft. (0.48 m3 ) 1 - 26.3 cu. ft. (0.74 m3 ) 2 - 58.0 cu. ft. (1.64 m3 ) 3
USA Canada Max roof load 220 lbs 100 kg Max trailer weight (w/o brakes) 1100 lbs 500 kg Max trailer weight* - (with brakes, 2" ball) - (with brakes, 1 7/8" ball) Max tongue weight *
3300 lbs 1500 kg 2000 lbs 900 kg 165 lbs 75 kg
WARNING! When adding accessories, equipment, luggage and other cargo to your vehicle, the total loaded weight capacity of the vehicle must not be exceeded.
USA
Canada
2100 kg 2130 kg 2120 kg 2150 kg 2220 kg 2220 kg 420 kg
1) Rear seat backrest up, load height - upper edger of backrest
2) Rear seat backrest folded down, load height - upper edge of front seat backrests/lower edge of rear window
3) Rear seat backrest folded down, load height - headlining (ceiling)
Weights
Gross vehicle weight (GVW)
V70 man.
4630 lbs
4690 lbs
V70 aut.
4670 lbs
V70 Turbo man.
V70 Turbo aut.
4730 lbs
4890 lbs
V70 AWD
XC70
4890 lbs
Capacity weight *** 930 lbs
Curb weight
V70
V70 AWD
XC70
Permissible axle weight, front
V70 man.
2290 lbs
2330 lbs
V70 aut.
2400 lbs
V70 Turbo aut.
V70 AWD
2400 lbs
XC70
2490 lbs
Permissible axle weight, rear
V70, V70 Turbo
2470 lbs
2580 lbs
V70 AWD
XC70
2620 lbs
3390-3585 lbs 1541-1632 kg 3690-3725 lbs 1675-1695 kg 3765-3800 lbs 1710-1730 kg
1040 kg 1060 kg 1090 kg 1090 kg 1130 kg
1120 kg 1170 kg 1190 kg
* When driving for prolonged periods at temperatures above 86° F (30° C), the maximum recommended weight is 2000 lbs (900 kg). **See also section "Trailer towing" *** The max permissible axle loads or the gross vehicle weight must not be exceeded.
All specifications are subject to change without prior notice.
pg. 144 Engine specifications
Engine specifications
Designation: Volvo B 5234 T3
Output Max. torque
247 hp at 5200 rpm (184 kW/87 rps) 243 ft. lbs. at 2400-5200 rpm (330 Nm/42-87 rps)
Number of cylinders 5
Bore
Stroke
Displacement
Compression ratio
Number of valves
3.19" (81 mm)
3.54" (90 mm)
2.3 liters
8.5:1
20
Designation: Volvo B 5254 T2
208 hp at 5000 rpm (154 kW/83 rps) 236 ft. lbs. at 1500-4500 rpm (320 Nm/25-75 rps)
Output
Max. torque
Number of cylinders 5
Bore
Stroke
Displacement
Compression ratio
Number of valves
3.27" (83 mm)
3.67" (93.2 mm)
2.5 liters
9.0:1
20
Designation: Volvo B 5244 T3
197 hp at 6000 rpm (147 kW/100 rps) 210 ft. lbs. at 1800-5000 rpm (285 Nm/30-83 rps)
Output
Max. torque
Number of cylinders 5
Bore
Stroke
Displacement
Compression ratio
Number of valves
3.27" (83 mm)
3.54" (90 mm)
2.4 liters
9.0:1
20
Designation: Volvo B 5244 S
168 hp at 6000 rpm (125 kW/100 rps) 166 ft. lbs. at 4500 rpm (225 Nm/75 rps)
Output
Max. torque
Number of cylinders 5
Bore
Stroke
Displacement
Compression ratio
Number of valves
3.27" (83 mm)
3.54" (90 mm)
2.4 liters
10.3:1
20
Charge air cooler (Intercooler) Turbocharged engines employ a turbo-compressor to force air into the engine inlet manifold and a charge air cooler to cool the compressed inlet air. The resulting increase in air flow raises pressure in the intake manifold and increases engine power over that developed by A normally-aspirated engine. The charge air cooler (which resembles a radiator) is located between the turbo-compressor and inlet manifold.
pg. 145 Transmission specifications
Power transmission
Manual transmission: M 56 LK
Single-disc dry plate clutch. All-synchromesh on all gears including reverse; integrated final drive. Operation via a
floor mounted gear lever.
Final drive ratio 4.00:1
Reduction ratios
1st gear 3.39:1
2nd gear 1.91:1
3rd gear 1.19:1
4th gear 0.87:1
5th gear 0.70:1
Reverse 3.30:1
Automatic transmission: AW 55-50
5-speed automatic electronically controlled gearbox comprising a hydraulic torque converter with a lock-up function;
planetary gear, integrated final drive.
Operation via a floor mounted gear selector lever. Drive shafts with symmetrical joint location. Overdrive.
Final drive ratio 2.44:1*
Reduction ratios AW5
1st gear 4.77:1
2nd gear 2.10:1
3rd gear 1.96:1
4th gear 1.32:1
5th gear 1.02:1
Reverse 3.23:1
* XC70 2.65:1
pg. 146 Oil/fluid specifications and volumes
Engine Oil
Meeting or exceeding ILSAC specification GF-2, including ACEA A1, API SJ, SJ/CF, and SJ/Energy Conserving.
Oil additives must not be used.
Volume: Capacity (including oil filter): 6.1 US qts. (5.8 liters) Automatic Transmission Fluid
AW5: Only Volvo gearbox oil (1161540-8). Do not mix with other oils. Volume: 7.9 US qts (7.5 liters) Cooling system
Type: Positive pressure, closed system. The thermostat begins to open at 194 °F (90 °C)
Coolant: Volvo original coolant/antifreeze
All specifications are subject to change without prior notice. Power steering fluid
ATF fluid Volume: 0.95 US qts (0.9 liters) Brake fluid
DOT 4+ boiling point >536°F(280°C), P/N 9437433
Volume: 0.64 US qts (0.6 liters)
Climate control system - refrigerant (R 134a)
Oil: PAG Volume: 2.2 lbs (1,000 g) R134a Fuel
Minimum octane requirement - AKI 87 (RON 91) Volume (fuel tank): 18.5 US gals (70 liters) or 19 US gals (72 liters) on models equipped with All Wheel Drive. Washer fluid reservoir
Volume: 4.7 US qts (4.5 liters)
All specifications are subject to change without prior notice.
pg. 147 Fuel system, Distributor ignition system, Suspension
Fuel system
The engine is equipped with a multiport fuel injection system. Distributor ignition system
Firing order: 1-2-4-5-3 Electronic ignition setting: Not adjustable Spark plugs: Champion RC8PYP 8 (or equivalent) Spark plug gap: 0.028-0.032" (0.7-0.8 mm) Tightening torque: 18.4 ft. lbs. (25 Nm)
WARNING! The ignition system operates at very high voltages. Special safety precautions must be followed to prevent injury.
Always turn the ignition off when:
Replacing ignition components e.g. plugs, coil, etc. Do not touch any part of the ignition system while the engine is running. This may result in a shock and bodily
injury.
Front suspension
Spring strut suspension with integrated shock absorbers and control arms linked to the support frame. Power-assisted rack and pinion steering. Safety type steering column. The alignment specifications apply to an unladen car but include fuel, coolant and spare wheel. Rear suspension
Individual rear wheel suspension with longitudinal support arms, double link arms and track rods.
All specifications are subject to change without prior notice.
pg. 148 Electrical system
Electrical system
12 Volt, negative ground. Voltage-controlled generator. Single-wire system with chassis and engine used as conductors. Grounded on chassis.
Battery Voltage: 12 Volt, capacity: 600 A/115 min reserve capacity. The battery contains corrosive and poisonous acids. It is of the utmost importance that old batteries are disposed of correctly. Your Volvo retailer can assist you in this matter.
Generator Rated output: max. current: 140 A
Starter motor: Output: 1.7 kW Bulbs
Bulb Headlights - High beam - Low beam Front parking lights Front direction indicators Front fog lights Rear direction indicators Tail lights
US no. Power
Socket
HB3
H7
60W 55W 5W
(yellow) 21 W
H1
55 W
(yellow) 21W
5W
67
W2.1x9.5d BAU 15d BAU 15 s BA 15 s
Brake lights Backup lights Rear fog light/rear parking lights License plate light Door step courtesy lights Front Cargo area lights Glove compartment light Vanity mirror light(s) Instrument lighting
1156
1156
BA 15 s 21W 21W BA 15 s 21/4W BA 15 s 5 W
W 2.1x9.5d
SV 8.5
SV 8.5
BA 9s
5W 5 W 2 W 12V 1.2W - 3 W
W 2.1x9.5d
All specifications are subject to change without prior notice.
pg. 149 Volvo On Call
Your new Volvo comes with a four year ON CALL road assistance. Additional information, features, and benefits are described in a separate information package in your glove compartment.
If you have misplaced your package, dial: In the U.S.A. 1-800-63-VOLVO (1-800-638-6586) In Canada: 1-800-263-0475
Technician certification
In addition to Volvo factory training, Volvo supports certification by the National Institute for Automotive Excellence (A.S.E.). Certified technicians have demonstrated a high degree of competence in specific areas. Besides passing exams, each technician must also have worked in the field for two or more years before a certificate is issued. These professional technicians are best able to analyze vehicle problems and perform the necessary service procedures to keep your Volvo at peak operating condition. All specifications are subject to change without prior notice.
Contents | Top of Page
2 0 0 3 VOLVO
V70
19
29
31
35
159
48 - 51
132
131
46
80, 81
80
94
109
14
19
29
104, 131
76
65
39, 59
151
162
160
152
153
165
159
128
INDEX
pg. 171 - 174 Index
ABS ABS - warning light Accessory lights Adjusting the steering wheel Advanced User Mode (AUM) - radio Air conditioning Air filter - engine Air pump system Air vents Airbag (SIPS) Airbag (SRS) Alarm Alarm - "panic" function All Wheel Drive - general information - using snow chains ALR/ELR Anti-lock Brake System (ABS) Anti-lock Brake System - warning light Antifreeze Approach lighting Armrest (center) - 3-section rear seat Ashtray Audio systems - cassette deck - CD player - HU-613 - overview - HU-803 - overview - specifications AUM (Advanced User Mode) - radio Automatic car washing
Automatic Locking Retractor (ALR) Automatic transmission - Geartronic - Kickdown Automatic transmission - cold starts Auxiliary socket AWD - general information - using snow chains Backrest (center) - 3-section rear seat Battery Battery maintenance - Replacing the battery - Ventilation hose Booster cushion Brake failure warning light Brake fluid Brake system Bulbs (list) Bulbs - replacing Capacities (oils and fluids) Cargo compartment cover Cargo compartment lighting Cargo eyelets Cargo net Catalytic converters - three-way Center armrest - 3-section rear seat Center backrest (3-section rear seat) Center console - switches Center head restraint - 3-section rear seat Center head restraint - rear seat Center seat head restraint Central locking buttons Chains - winter driving Changing wheels Child booster cushion Child Restraint Anchorages Child safety Child safety locks - rear doors Climate controls Climate system - general information Clock
14
90, 91, 145
92, 93
91, 92
91
31, 39
94
109
64
104, 148
138, 139
139
139
12, 16
28
137
18
148
120-125
141, 146
71
67
68
69
106
65
64
31
64
63
79
109
112, 113
12, 16
15
11, 12, 14, 16
82
48-51
47
27
Clutch interlock Coat hanger Coin compartment Cold weather driving Combination filter Coolant Cooling system - general information Courtesy light Courtesy lights (front) - replacing Courtesy lights - exterior Cruise control Cup holder Cup holder in the center console Detachable trailer hitch - installing Dimensions Direction indicators Distributor ignition system Door step courtesy lights - replacing Doors and locks Drive belt Driver's seat and remote keyless entry system Driving economy Driving mode indicator Driving mode W Driving with trunk open Economical driving Electric socket in cargo compartment Electrical system Electrical system - general information Electrically operated front seats Electrically operated sideview mirrors Electrically operated sun roof Electrically operated windows Electronic Brake Force Distribution Electronic Climate Control (ECC) Emergency Locking Retractor (ELR) Emergency towing Emergency warning flashers Emissions systems Engine - specifications Engine - starting Engine air filter
89
61
59
104
48, 51
131
96
74
124
76
33
59
60
102
143
36
147
123
76
131
57
95
27
91, 93, 104
96
95
67
148
96
56
41
42
40
19
48 - 51
14
99, 100
38
130
144, 145
87, 88
132
Engine compartment
Engine oil
Extension of cargo compartment
Exterior courtesy lights
Exterior features - overview
Extra seat
Fog light - rear
Fog lights - front
Folding passenger's seat backrest
Foldtable
Front airbags - SRS
Front airbags - SRS - warning light
Front courtesy lights - replacing
Front fog lights
Front fog lights - replacing
Front reading lights
Front seats - adjusting
Front seats - heated
Front seats - manual adjustment
Front suspension
Fuel
Fuel filler cap
Fuel filter
Fuel gauge
Fuel requirements
Fuel system
Fuel tank cover
Fuel/emissions systems
Fuses
Gas cap
Gasoline
Gear indicator
Geartronic (automatic transmission)
Generator
Generator warning light
Hand brake
Handgrip - XC70
Handling
Hazard warning flashers
Head restraint (center) - 3-section rear seat
Head restraint - center rear
134
104, 135, 136
63
76
25
73
29, 34
34
57
62
4 - 7
28
124
34
124
74
56
38
58
147
84
86
132
27
84
130, 132, 147
86
130
116-119
86
84
27
92, 93
148
28
39
55, 73
95
38
64
Headlight bulbs - replacing Headlight wiper blades - replacing Headlights Heated front seats Heated rear window Heated sideview mirrors Heating Hoisting the car Holder for grocery bags Home Safe System HomeLink® Hood - opening Ignition switch Immobilizer (start inhibitor) Indicator lights Inflatable curtain (IC) Instrument illumination Instrument panel Instruments Integrated booster cushion Interior Air Quality system Interior features - overview Interior lighting Jack Jump starting Key - removing from ignition switch Keyless entry system Keyless entry system - replacing batteries Keylock Keys Kickdown Label information License plate lights - replacing Lifting the car Lights - accessory Load carriers Locking and unlocking the car Locking steering wheel Long distance trip Long loads
120
140
34
38
38
38
48-51
133
67
76
167-169
134
35
76, 87
28, 29
34
27
26
12
51
24
74
72, 112
103
87
77, 78
78
87
76
91, 92
142
124
133
31
97
76
35
105
57
17
84
27
104, 135, 136
28
134
129
29
52-54
89, 145
56
41
41
69
69
Maintenance schedule
Malfunction indicator lamp
Manual climate control with air conditioning
Manual transmission
Memory function - front seats
Mirrors
Mirrors, sideview - memory function
Net - cargo
Nylon cargo net
Occupant safety
Octane rating
Odometer
Oil - engine
Oil pressure warning light
Opening the hood
Paint touch-up
Panic function (alarm)
Parking brake
Parking brake reminder light
Parking lights
Passenger's seat backrest - folding
PCV system
Pen holder
Polishing
Power seats
Power steering fluid
Power windows
151
Radio
37
Rain sensor - windshield wipers
74
Reading lights - front/rear
29, 34
Rear fog light
74
Rear reading lights
66
Rear seat backrest
38
Rear window - heated
41
Rearview mirror
47
Refrigerant
Refueling
86
Remote central locking system and sideview mirrors system 41
77
Remote control - keyless entry system
126
80
39
28
34
57
132
61
128
56
137
40
Remote control - Homelink® Universal Transceiver Remote keyless entry system Remote keyless entry system - replacing batteries Remote keyless entry system and driver's seat Removing the seat cushion Replacing bulbs Replacing fuses Replacing wiper blades Road assistance Roadholding Roof load - maximum Roof racks Safety locks - child Seat belt maintenance Seat belts Seat belts - cleaning Seats - front Securing cargo Servicing Shiftlock Side direction indicator - replacing Side impact airbag system (SIPS) Sideview mirrors Sideview mirrors - heated Sideview mirrors - memory function Snow chains Snow tires Spare tire Spark plugs Specifications SRS SRS diagnostic system Stability Traction Control (STC) Stain removal Start inhibitor (immobilizer) Starting the engine Steel grid Steering wheel adjustment Steering wheel lock Stop and Store bag Storage compartments Storage in the glove compartment Studded tires
168
77
78
57
66
120-125
116
140
149
95
143
97
82
17
2, 3, 14
128
56
68
133
87, 90, 92
123
41
38
41
109
109
72, 110
132, 147
144
28
19, 31
128
76, 87
87, 88
69
35
35
64
59
60
109
Subwoofer Sun roof Supplemental Restraint System Suspension Switches in center console Tachometer Tailgate - locking/unlocking Tailgate wiper blade - replacing Temperature gauge Temporary spare tire Text window Three-way catalytic converters Timing belt Tire pressure Tires Tires - changing Tool bag Towing a trailer Towing eyelet Towing the car Trailer towing Trailer weight - maximum Transmission - automatic Trip computer Trip odometer Turn signals Uniform tire quality grading Unlocking the tailgate Upholstery - cleaning Vanity mirror lights - replacing Vehicle Identification Number (VIN) Vehicle loading Ventilation Volvo On Call Volumes (oils and fluids) Warning flashers Warning light - center Warning lights Warranty Washer fluid reservoir
72, 166
42, 43
4, 28
147
31
27
79
140
27
110
30
106
132
110
108 -111
112, 113
72
101
99
99, 100
101
143
90-94
32
27
36
111
79
128
124
142
110
46
149
146
38
28
28, 29
129
133
Washer fluid solvent Washing the car Waxing Weight distribution Wheels - changing Wheels and tires Whiplash Protection System (WHIPS) Windows - electrically operated Windshield washer solvent Windshield wiper blades - replacing Windshield wipers/washers Winter driving Winter tires Winter/Wet driving mode Wiper blades - replacing
104
127, 128
128
95
112, 113
108-113
10
40
104
140
37
104
109
91, 93, 104
140
Contents | Top of Page
2 0 0 3 VOLVO
V70
Back Cover
Back Cover
Accessory Installation - Important Warning
We strongly recommend that Volvo owners install only genuine, Volvo-approved accessories, and that accessory
installations be performed only by the factory-trained technicians at your authorized Volvo retailer.
Genuine Volvo accessories are tested to ensure compatibility with the performance, safety, and emission systems in your car. Additionally, your authorized Volvo retailer knows where accessories may and may not be safely installed in your Volvo. In all cases, please consult your authorized Volvo retailer before installing any accessory in or on your car.
Accessories that have not been approved by Volvo may or may not be specifically tested for compatibility with your
car. Additionally, an inexperienced installer may not be familiar with some of your car's systems.
Any of your car's performance and safety systems could be adversely affected if you install accessories that Volvo
has not tested, or if you allow accessories to be installed by someone unfamiliar with your car.
Damage caused by unapproved or improperly installed accessories may not be covered by your new car warranty.
See your Warranty and Service Records Information booklet for more warranty information. Volvo assumes no responsibility for death, injury, or expenses that may result from the installation of non-genuine accessories.
Driver Distraction
Driver distraction results from driver activities that are not directly related to controlling the car in the driving environment. Your new Volvo is, or can be, equipped with many feature-rich entertainment and communication systems. These include hands-free cellular telephones, navigation systems, and multipurpose audio systems. You may also own other portable electronic devices for your own convenience. When used properly and safely, they enrich the driving experience. Improperly used, any of these could cause a distraction.
For all of these systems, we want to provide the following warning that reflects the strong Volvo concern for your
safety:
parked.
Never use these devices or any feature of your vehicle in a way that distracts you from the task of driving safely.
In addition to this general warning, we offer the following guidance regarding specific newer features that may be
Never use a hand-held cellular telephone while driving. Some jurisdictions prohibit cellular telephone use by a
Distraction can lead to a serious accident.
found in your vehicles:
driver while the vehicle is moving.
If your car is equipped with a navigation system, set and make changes to your travel itinerary only with the vehicle
Never program your audio system while the vehicle is moving. Program radio presets with the vehicle parked, and
use your programmed presets to make radio use quicker and simpler.
Never use portable computers or personal digital assistants while the vehicle is moving.
A driver has a responsibility to do everything possible to ensure his or her own safety and the safety of passengers in
the vehicle and others sharing the roadway. Avoiding distractions is part of that responsibility.
The following should be checked regularly: *
1 Washer fluid reservoir should be filled with water and solvent (wintertime: windshield washer anti-freeze). See page 133.
2 Power steering - When cold, the level must not be above the COLD mark and when hot it must not be above the HOT mark. Top up if the level drops to the ADD mark with ATF fluid. See page 137.
3 Coolant level should be between the expansion tank marks. Mixture: 50% anti-freeze and 50% water. See page 131.
4 Engine oil level should be between the dipstick marks. The distance between the marks represents approx. 1.6 US qts (1.5 liters). See page 135.
5 Brake fluid - check, without removing the cap, that the level is above the MIN mark. Use brake fluid DOT 4+. See page 137.
* Engine oil should be checked each time the car is refuelled.
Octane rating, see page 84.
Tire pressure, see label located on the rear edge of the right front door.
Bulbs Power Socket US no.
US no.
Bulb Power Socket
60 W HB 3
55 W H 7
21 W BAU 15d -
21 W BA 15s
55 W H 1
5 W W W2.1x9.5d 1157NA
21/4 W BA 15d
5 W BA 15s
1156
67
Contents | Top of Page
2 0 0 3 VOLVO
V70
This manual deals with the operation and care of your Volvo.
Welcome to the worldwide family of Volvo owners. We trust that you will enjoy many years of safe driving in your Volvo, an automobile designed with your safety and comfort in mind. To help ensure your satisfaction with this vehicle, we encourage you to familiarize yourself with the equipment descriptions, operating instructions and maintenance requirements/recommendations in this manual. We also urge you and your passengers to wear seat belts at all times in this or any other automobile. And, of course, please do not operate a vehicle if you may be affected by alcohol, medication or any impairment that could hinder your ability to drive. Your Volvo is designed to meet all applicable safety and emission standards, as evidenced by the certification labels attached to the driver's door opening and on the left wheel housing in the engine compartment.
For further information please contact your retailer, or: In the USA:
In Canada:
Volvo Cars of North America
Customer Relations
P.O. Box 914
Rockleigh, New Jersey 07647-0914 800-663-8255
800-458-1552
Volvo Canada Ltd.
175 Gordon Baker Road
North York, Ontario M2H 2N7
We also invite you to visit our Home Page on the Internet at:
http://www.volvocars.com
Contents
Contents Chapter 1 - Safety Chapter 2 - Instruments, switches and controls Chapter 3 - Climate control system Chapter 4 - Interior Chapter 5 - Keys, Locks, Alarm Chapter 6 - Starting and driving Chapter 7 - Wheels and tires Chapter 8 - Maintenance/Servicing Chapter 9 - Specifications Chapter 10 - Audio systems HomeLink® Universal Transceiver (option) Index Back Cover General information
Shiftlock
When your car is parked, the gear selector is locked in the (P)ark position. To release the selector from this position, turn the ignition key to position II (or start the engine), depress the brake pedal, press the button on the front of the gear selector knob and move the selector from (P)ark.
Keylock
This means that when you switch off the ignition, the gear selector must be in the (P)ark position before the key can be removed from the ignition switch.
Anti-lock Brake System (ABS)
The ABS system in your car performs a self-diagnostic test when the vehicle first reaches the speed of approximately 12 mph (20 km/h). The brake pedal will pulsate several times and a sound may be audible from the ABS control module. This is normal.
Fuel filler door
Press the button on the light switch panel (see page 34) when the car is at a standstill to unlock the fuel filler door. Please note that the fuel filler door will remain unlocked until the car begins to move forward. An audible click will be heard when the fuel filler door relocks.
Fuel filler cap
After refueling, close the fuel filler cap by turning it clockwise until it clicks into place. If this cap is not closed tightly or if the engine is running when the car is refueled, the Malfunction Indicator Lamp ("Check Engine" light) may indicate a fault. Important
Before you operate your car for the first time, please familiarize yourself with the new-engine oil consumption information on page 135. You should also be familiar with the information in the chapters one, two and four of this manual.
Information contained in the balance of the manual is extremely useful and should be read after operating the vehicle for the first time.
The manual is structured so that it can be used for reference. For this reason, it should be kept in the car for ready access.
Do not export your Volvo to another country before investigating that country's applicable safety and exhaust emission requirements. In some cases it may be difficult or impossible to comply with these requirements. Modifications to the emission control system(s) may render your Volvo not certifiable for legal operation in the U.S., Canada and other countries.
All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of publication. Please note that some vehicles may be equipped differently, depending on special legal requirements and that optional equipment described in this manual may not be available in all markets.
Volvo reserves the right to make model changes at any time, or to change specifications or design, without notice and without incurring obligation.
CALIFORNIA Proposition 65 Warning WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California to cause cancer, and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm.
Volvo and the environment
Volvo is committed to the well being of our customers. As a natural part of this commitment, we care about the
environment in which we all live. Caring for the environment means an everyday involvement in reducing our environmental impact.
Volvo's environmental activities are based on a holistic view, which means we consider the overall environmental impact of a product throughout its complete life cycle. In this context, design, production, product use, and recycling are all important considerations.
In production, Volvo has partly or completely phased out several chemicals including freons, lead chromates, naphtanates, asbestos, mercury and cadmium; and reduced the amount of chemicals used in our plants 50% since 1991.
In use, Volvo was the first in the world to introduce into production a three-way catalytic converter with a Lambda sond, now called oxygen sensor, in 1976. The current version of this highly efficient system reduces emissions of harmful substances (CO, HC, NOx) from the exhaust pipe by approximately 95% and the search to eliminate the remaining emissions continues. Volvo is the only automobile manufacturer to offer CFC-free retrofit kits for the air conditioning system for all models as far back as the M/Y 1975 240. Advanced electronic engine controls, refined purification systems and cleaner fuels are bringing us closer to our goal.
After Volvo cars and parts have fulfilled their use, recycling is the next critical step in completing the life cycle. The metal content is about 75% of the total weight of a car, which makes the car among the most recycled industrial products. In order to have efficient and well controlled recycling, many Volvo variants have printed dismantling manuals, indicating the weight and material of individual components. For Volvo, all homogeneous plastic parts weighing more than 1.7 oz. (50 grams) are marked with international symbols that indicate how the component is to be sorted for recycling.
In addition to continuous environmental refinement of conventional gasoline-powered internal combustion engines, Volvo is actively looking at advanced technology alternative-fuel vehicles.
When you drive a Volvo, you become our partner in the work to lessen the car's impact on the environment.
To reduce your vehicle's environmental impact, you can:
Maintain proper air pressure in your tires. Tests have shown decreased fuel economy with improperly inflated tires Follow the recommended maintenance schedule Drive at a constant speed See an authorized Volvo retailer as soon as possible for inspection if the check engine (malfunction indicator) lamp
illuminates, or stays on after the vehicle has started
Properly dispose of any vehicle related waste such as used motor oil, used batteries, brake pads, etc. When cleaning your car, use Volvo's own car care products, all of which have systematically been adapted to the
environment
Prem-Air®
On the surface of the radiator in the engine compartment, there is a special coating called Prem-Air®. Prem-Air® works as a catalytic converter, converting most of the ozone passing through the radiator into oxygen, thereby reducing harmful ground-level ozone.
For additional information regarding the environmental activities in
which Volvo Cars of North America, LLC. and Volvo Car of Canada, Ltd. are involved, visit our Internet Home Page at: http://www.volvocars.com
Top of Page
2 0 0 3 VOLVO
V70
Chapter 1 - Safety
pg. 1 Safety
Not wearing a seat belt is like believing "It'll never happen to me!" Volvo, the inventor of the three-point seat belt, urges you and all adult occupants of your car to wear seat belts and ensure that children are properly restrained, using an infant, car or booster seat determined by age, weight and height. Volvo also believes no child should sit in the front seat of a car.
Fact: In every state and province, some type of child-restraint legislation has been passed. Additionally, most states and provinces have already made it mandatory for occupants of a car to use seat belts.
So, urging you to "buckle up" is not just our recommendation - legislation in your state or province may mandate seat belt usage. The few seconds it takes to buckle up may one day allow you to say, "It's a good thing I was wearing my seat belt."
Seat belts 2
Center head restraint 3
Front airbags (SRS) 4
Side impact airbags (SIPS) 8
Volvo Inflatable Curtain (VIC) 9
Whiplash Protection System (WHIPS) 10
Child safety 11
Occupant safety 17
Brake system 18
Anti-lock Brake System (ABS) 19
Stability Traction Control (STC) 20
Dynamic Stability Traction Control (DSTC) 20
pg. 2 Seat belts
Seat belts
Always fasten the seat belts before you drive or ride. A chime will sound several times if the driver's seat belt is not fastened.