2013 Volvo V60 Owners Manual

Download PDF Manual
03 Your driving environment Seats Front seats 03 WARNING Adjust the position of the driver's seat before setting off, never while driving. Make sure that the seat is in locked position in order to avoid personal injury in the event of sudden braking or an accident. Lift the catches on the rear of the backrest and fold it forward. 4. Push the seat forward so that the head restraint "locks" in under the glovebox. Raising takes place in reverse order. Lowering the front seat backrest WARNING Grasp the backrest and make sure that it is properly locked after being folded up in order to avoid personal injury in the event of sudden braking or an accident. Lumbar support adjustment, turn the wheel1. Forward/backward: lift the handle to adjust the distance to the steering wheel and ped- als. Check that the seat is locked after changing position. Raise/lower* front edge of seat cushion, pump up/down. Adjust backrest rake, turn the wheel. Raise/lower the seat, pump up/down. Control panel for power seat*. The passenger seat backrest can be folded forward to make room for long loads. Move the seat as far back/down as possi- ble. Adjust the backrest to an upright position. 1 Also applies to power seat. 80 * Option/accessory, for more information, see Introduction. 03 Your driving environment Power seat* trol key without the key in the ignition switch. Seat adjustment is normally made in key posi- tion I and can always be made when the engine is running. Seat with memory function* Seats 2. Hold the button depressed to store set- tings while depressing one of the memory buttons. Using a stored setting Hold one of the memory buttons depressed until the seat and the door mirrors stop. If you release the button then the movement of the seat will stop. Key memory* in remote control key2 03 Front edge of seat cushion up/down Seat forward/backward and up/down Backrest rake The power front seats have overload protection which is tripped if a seat is blocked by an object. If this happens, go to key position I or 0 and wait a short time before adjusting the seat again. Only one movement (forward/back/up/down) can be made at a time. Preparations The seats can be adjusted for a certain time after unlocking the door with the remote con- Store setting Memory button Memory button Memory button Button for storing settings 1. Adjust the seat and the door mirrors. 2 For key memory for Keyless function, see page 55. 3 Only if the car is equipped with power seat with memory and retractable power door mirrors. All remote control keys can be used by differ- ent drivers to store the settings for the driver's seat and door mirrors3. Proceed as follows: • Adjust the seat as you want it. • Lock the car by pressing the lock button on the remote control key that you normally * Option/accessory, for more information, see Introduction. `` 81 03 Your driving environment Seats use. This stores the positions of the seat and door mirrors in the remote control key's memory4. • Unlock the car (by pressing the unlock but- ton on the same remote control key) and open the driver's door. The driver's seat and door mirrors will automatically adopt the positions that are stored in the remote control key's memory (if the seat has been moved since you locked the car). The key memory can be activated/deactivated in the menu system MY CAR under Settings Car settings Car key memory. For a description of the menu system, see page 202. Emergency stop If the seat accidentally begins to move, press one of the setting buttons for the seat or mem- ory buttons in order to stop the seat. Restarting to reach the seat position stored in the key memory is performed by pressing the unlock button on the remote control key. The driver's door must then be open. WARNING Risk of crushing! Make sure that children do not play with the controls. Check that there are no objects in front of, behind or under the seat during adjustment. Ensure that none of the backseat passengers will be trapped. Heated seats For heated seats, see page 215. Rear seats Head restraint, centre seat, rear head is covered if possible. Slide it up as required. To lower the head restraint again, the button (located in the centre between the backrest and head restraint, see illustration) must be pressed in while the head restraint is pressed down carefully. Manual lowering of the outer head restraints, rear seat Pull the locking handle closest to the head restraint to fold the head restraint forward. The head restraint is moved back manually until a "click" can be heard. Adjust the head restraint according to passen- ger height so that the whole of the back of the 4 This setting does not affect settings that have been stored in the power seat's memory function. 03 82 WARNING The head restraints must be in locked posi- tion after being raised. Lowering the rear seat backrest IMPORTANT There must be no objects on the rear seat when the backrest is to be folded down. The seat belts must not be connected either. Otherwise there is a risk of damaging the rear seat upholstery. The triple-section backrest can be folded in different ways. NOTE The front seats may need to be pushed for- wards, and/or the backrests adjusted upwards, in order that the rear backrests can be folded forward fully. • The left-hand section can be folded sepa- rately. • The centre section can be folded sepa- rately. • The right-hand section can only be folded together with the centre section. 03 Your driving environment Seats • If the entire backrest is to be folded then the different sections should be folded separately. the lock catch is no longer locked in place. shows that the backrest NOTE When the backrests have been lowered the head restraints must be moved forward slightly so as not to make contact with the seat cushion. 03 Raising takes place in reverse order. NOTE When the backrest has been raised, the red indicator should no longer be showing. If it is still showing then the backrest is not locked in place. WARNING Check that the backrests and head restraints in the rear seats are firmly locked after raising. 83 If the centre backrest is being lowered - fold and adjust the centre backrest's head restraint downwards, see page 82. The outer head restraints are lowered auto- matically when the outer backrests are lowered. Pull up the backrest's locking handle while folding the backrest for- ward at the same time. A red indicator on 03 Your driving environment Seats Electrical lowering of the rear seat's outer head restraints* WARNING The head restraints must be in locked posi- tion after being raised. 03 1. The remote control key must be in position I or II. 2. Press the button to lower the rear outer head restraints to improve rearward visi- bility. WARNING Do not lower the outer head restraints if there are any passengers using of the outer seats. Move the head restraint back manually until a click is heard. 84 * Option/accessory, for more information, see Introduction. 03 Your driving environment Steering wheel Adjusting WARNING Horn Adjust and secure the steering wheel before driving. With speed related power steering* the level of steering force can be adjusted, see page 226. Keypads* 03 Horn. Press the centre of the steering wheel to signal. Adjusting the steering wheel. Lever - releasing the steering wheel Possible steering wheel positions The steering wheel can be adjusted for both height and depth: 1. Pull the lever towards you to release the steering wheel. 2. Adjust the steering wheel to the position that suits you. 3. Push back the lever to fix the steering wheel in place. If the lever is stiff, press the steering wheel lightly at the same time as you push the lever back. Keypads in the steering wheel. Cruise control, see page 152 Adaptive cruise control, see page 154 Audio and phone control, see page 235. * Option/accessory, for more information, see Introduction. 85 03 Your driving environment Lighting Headlamp control Headlamp control with AUTO mode 03 Overview, headlamp control. Overview, headlamp control. Thumbwheel for adjusting display and instrument lighting Rear fog lamp Headlamp control Thumbwheel for adjusting display and instrument lighting Rear fog lamp Headlamp control Thumbwheel1 for headlamp levelling Thumbwheel1 for headlamp levelling Instrument lighting Different display and instrument lighting is switched on depending on key position, see page 78. The display lighting is automatically subdued in darkness - the sensitivity is set with the thumbwheel. 1 Not available for cars equipped with active Xenon headlamps*. 86 * Option/accessory, for more information, see Introduction. The intensity of the instrument lighting is adjusted with the thumbwheel. Headlamp levelling The load in the car changes the vertical align- ment of the headlamp beam, which could daz- zle oncoming motorists. Avoid this by adjusting the height of the beam. Lower the beam if the car is heavily laden. 1. Leave the engine running, or have the car's electrical system in key position I. 2. Roll the thumbwheel up/down to raise/ lower beam alignment. Cars with active Xenon headlamps* have auto- matic headlamp levelling and are therefore not equipped with the thumbwheel. Main/dipped beam Position Specification Headlamp control with AUTO mode 03 Your driving environment Lighting Dipped beamA/Dipped beam off. Main beam can be activatedA. Main beam flash operates in this position. Position/parking lamps Dipped beam Main beam can be activated. Main beam flash operates in this position. A Applies to certain markets. Headlamp control and stalk switch. Position for main beam flash Position for main beam 03 Headlamp control and stalk switch. Position for main beam flash Position for main beam Position Specification Dipped beam off. Main beam flash operates in this position. Position/parking lamps * Option/accessory, for more information, see Introduction. `` 87 03 Your driving environment 03 Lighting Position Specification Dipped beamA/Dipped beam off in good light conditions. The "Tunnel detection*" function activates dipped beam in poor light conditions. The function for "Main beam with automatic activation*" can be used. Main beam flash operates in this position. Dipped beam Main beam can be activated. Main beam flash operates in this position. A Applies to certain markets. Volvo recommends that mode is used, as long as the traffic situation or weather con- ditions are not unfavourable for the function for "Main beam with automatic activation*". Main beam flash Move the stalk switch gently towards the steer- ing wheel to the position for main beam flash. Main beam comes on until the stalk switch is released. Dipped beam When the engine is started, dipped beam is activated automatically2 if the headlamp con- . If necessary, auto- trol is in position matic dipped beam for this position can be deactivated by a workshop. Volvo recom- mends that you contact an authorised Volvo workshop. In position dipped beam is always switched on when the engine is running or when key position II is active. 2 or Main beam Main beam can be activated when the head- lamp control is in position Activate/deactivate main beam by moving the stalk switch towards the steering wheel to the end position and release. Alternatively, the main beam can be deactivated by a light press of the stalk switch toward the steering wheel. When main beam has been activated the sym- illuminates in the combined instru- bol ment panel. 2 Applies to certain markets, for headlamp control without AUTO mode. 88 * Option/accessory, for more information, see Introduction. Main beam with automatic activation - AHB* Main beam with automatic activation (Active High Beam - AHB) is a function which uses a camera sensor at the top edge of the wind- screen to detect the headlamp beams of oncoming traffic or the rear lights of vehicles in front, and then switches from main beam to dipped beam. The lights are switched back to main beam a second or so after the camera sensor no longer detects any such light. In cars with this function the headlamp control has another design, see page 87. This function can be activated when the head- . For activation lamp control is in position to take place, the engine must have been run- ning for at least 20 seconds and the speed of the car must be 20 km/h or higher. 03 Your driving environment Lighting message goes out and the minates. symbol illu- WARNING AHB is an aid for using optimum light com- position when conditions are favourable. The driver always bears responsibility for manually switching between main and dipped beam when traffic situations or weather conditions so require. 03 When AHB has been activated the symbol illuminates in the combined instru- ment panel's display. When main beam has symbol also illumi- been activated the nates in the combined instrument panel. NOTE Keep the windscreen surface in front of the camera sensor clean from ice, snow, mist and dirt. Do not attach or fit anything to the wind- screen in front of the camera sensor, as this could reduce or prevent the function of one or more camera-dependent systems. If the message AHB temporary unavailable is shown in the combined instrument panel's display then you have to switch manually between main and dipped beam. However, the headlamp control may nevertheless be in posi- tion Windscreen Sensors blocked and the . The same applies if the message symbol are shown. The sym- bol goes out when these messages are shown. AHB may be temporarily unavailable e.g. in sit- uations with dense fog or heavy rain. When AHB becomes available again, or the wind- screen sensors are no longer covered, the Light switch in position AUTO. Activate/deactivate AHB by moving the left- hand stalk switch towards the steering wheel to the end position and release. Deactivation when main beam is on means that the lights switch directly to dipped beam. Headlamp control and stalk switch. 89 03 Your driving environment 03 Lighting IMPORTANT Examples of when manual switching between main and dipped beam may be required: • In heavy rain or dense fog • In snow flurries or slush • In moonlight • When driving in poorly lit built-up areas • When the traffic ahead has weak light- ing • If there are pedestrians on or beside the road • If there are highly reflective objects such as signs in the vicinity of the road e.g. driven into a tunnel, and dipped beam is activated within a second in markets without automatic dipped beam. Dipped beam is deac- tivated approx. 20 seconds after the car has been driven out of the tunnel. Note! - The head- lamp control must be in position for tun- nel detection to work. Active Xenon headlamps - ABL* • When the lighting from oncoming traffic is obscured by e.g. a crash barrier • When there is traffic on connecting roads • On the brow of a hill or in a hollow • In sharp bends. For more information on the limitations of the camera sensor, see page 178. Tunnel detection* In cars with rain sensor* the rain sensor detects the changed light conditions when the car is 3 Activated on delivery from the factory. Headlamp pattern with function deactivated (left) and activated (right) respectively. If the car is equipped with active Xenon head- lamps Active Bending Lights - ABL the light from the headlamps follows the steering wheel movement in order to provide maximum light- ing in bends and junctions and so provide increased safety. 90 * Option/accessory, for more information, see Introduction. The function is activated automatically when the car is started. In the event of a fault in the function the symbol illuminates in the combined instrument panel at the same time as the information display shows an explana- tory text and a further illuminated symbol. Symbol Display Headlamp failure Service required Specifica- tion The system is disen- gaged. Visit a workshop if the mes- sage remains. Volvo rec- ommends that you contact an authorised Volvo work- shop. The function is only active in twilight or dark- ness and only when the car is moving. The function3 can be deactivated/activated in the menu system MY CAR under My V60 03 Your driving environment Light settings Active Bending Lights or under Settings Car settings Active Bending Lights. For a description of the menu system, see page 203. For headlamp pattern adjustment, see page 94. Auxiliary lamps* If the car has auxiliary lamps, the driver can use the MY CAR menu system to choose whether they should be deactivated or switched on/off simultaneously with the main beam4, see page 204. Position/parking lamps Turn the headlamp control to the position for position/parking lamps (number plate lighting is illuminated at the same time). When it is dark outside and the tailgate is opened the rear position lamps illuminate to alert traffic behind. This takes place irrespec- tive of what position the headlamp control is in or what key position the car's electrical system is in. Brake lights The brake light automatically comes on during braking. For information on the Emergency brake lights and automatic hazard warning flashers, see page 135. Headlamp control in position for position/parking lamps. Lighting Rear fog lamp 03 Button for rear fog lamp. The rear fog lamp consists of one rear lamp and can only be switched on in combination with main/dipped beam. Press the button for On/Off. The rear fog lamp indicator symbol instrument panel and the light in the button illu- minate when the rear fog lamp is switched on. The rear fog lamp is switched off automatically when the engine is switched off. on the combined NOTE Regulations for using rear fog lamps vary between different countries. 4 Auxiliary lamps must be connected to the electrical system by a workshop. Volvo recommends that you contact an authorised Volvo workshop. * Option/accessory, for more information, see Introduction. 91 03 Your driving environment Lighting Hazard warning flashers Direction indicators/flashers 03 92 Button for hazard warning flashers. Press the button to activate the hazard warning flashers. Both direction indicator symbols in the combined instrument panel flash when the hazard warning flashers are in use. The hazard warning flashers are activated automatically when the car has been braked so suddenly that the emergency brake lights have been activated at a speed below 10 km/h. The hazard warning flashers remain on when the car has stopped and are deactivated automat- ically when the car is driven off again or the button is depressed. For more information on Emergency brake lights and automatic hazard warning flashers, see page 135. Direction indicators/flashers. Short flash sequence Move the stalk switch up or down to the first position and release. The direction indicators flash three times. The function can be activated/deactivated in the menu system MY CAR under Settings settings indicator. For a description of the menu system, see page 203. Light settings Triple Car Continuous flash sequence Move the stalk switch up or down to the outer position. The stalk switch remains in its position and is moved back manually, or automatically by the steering wheel movement. Direction indicator symbols For direction indicator symbols, see page 72. Interior lighting Controls in roof console for the front reading lamps and passenger compartment lighting. Reading lamp, left-hand side Reading lamp, right-hand side Interior lighting All lighting in the passenger compartment can be switched on and off manually within 30 minutes from when: • the engine has been switched off and the car's electrical system is in key position 0 • the car has been unlocked but the engine has not been started. 03 Your driving environment Front roof lighting The front reading lamps are switched on or off by pressing the relevant button in the roof con- sole. Vanity mirror The lighting for the vanity mirror, see page 229, is switched on and off respectively when the cover is opened or closed. Rear roof lighting Rear roof lighting. The lamps are switched on or off by pressing each respective button. Courtesy lighting Courtesy lighting (and passenger compart- ment lighting) is switched on and off respec- tively when a side door is opened or closed. Glovebox lighting Glovebox lighting is switched on and off respectively when the lid is opened or closed. Lighting, cargo area The lighting in the cargo area is switched on and off respectively when the tailgate is opened or closed. Automatic lighting The switch for passenger compartment light- ing has three positions for the lighting in the passenger compartment: • Off – right-hand side pressed in, automatic lighting deactivated. • Neutral position – automatic lighting acti- vated. • On – left-hand side pressed in, passenger compartment lighting switched on. Neutral position When the button is in neutral position the pas- senger compartment lighting is switched on and off automatically in accordance with the following. The passenger compartment lighting is switched on and remains on for 30 seconds if: Lighting • the car is unlocked with the remote control key or key blade, see pages 45 or 48 • the engine has been switched off and the car's electrical system is in key position 0. Passenger compartment lighting is switched off when: • the engine is started • the car is locked. The passenger compartment lighting comes on and remains on for two minutes if one of the doors is open. If any lighting is switched on manually and the car is locked then it will be switched off auto- matically after two minutes. Mood lights When the normal passenger compartment lighting is switched off and the engine is run- ning, a number of LEDs illuminate, including one in the ceiling lighting, in order to provide a low-light and enhance the mood while driving. This lighting goes out for a little while after the normal passenger compartment lighting when the car is locked. 03 `` 93 03 Your driving environment Lighting Home safe light duration Some of the exterior lighting can be kept switched on to work as home safe lighting after the car has been locked. 1. Remove the remote control key from the ignition switch. 2. Move the left-hand stalk switch toward the steering wheel to the end position and release it. The function can be activated in the same way as with main beam flash, see page 87. 03 3. Get out of the car and lock the door. When the function is activated, dipped beam, parking lamps, door mirror lamps, number plate lighting, interior roof lamps and courtesy lighting are switched on. The length of time for which the home safe lighting should be kept on can be set in the menu system MY CAR under Settings settings duration. For a description of the menu sys- tem, see page 203. Car Home safe light Light settings Approach light duration Approach lighting is switched on with the remote control key, see page 45, and is used to switch on the car's lighting at a distance. When the function is activated with the remote control, parking lamps, door mirror lamps, number plate lighting, interior roof lamps and courtesy lighting are switched on. The length of time for which the approach light- ing should be kept on can be set in the menu system MY CAR under Settings settings Approach light duration. For a description of the menu sys- tem, see page 203. Light settings Car Adjusting headlamp pattern Headlamp pattern, right-hand traffic. The headlamp pattern must be adjusted to avoid dazzling oncoming motorists and can be set for right or left-hand traffic. The correct pat- tern will also better illuminate the verge. Active Xenon headlamps* The car must be stationary with the engine run- ning when the headlamp pattern is shifted between right and left-hand traffic. 1. Access the menu system MY CAR under Settings settings. Car settings Light Headlamp pattern, left-hand traffic. 2. Select between Temporary RH traffic and Temporary LH traffic. For a description of the menu system, see page 203 94 * Option/accessory, for more information, see Introduction. Halogen headlamps The headlamp pattern for halogen headlamps is readjusted by masking the headlamp lens. The headlamp pattern may not be as good. Masking the headlamps 1. Copy the A and B templates for left-hand drive cars or the C and D templates for right-hand drive cars with a scale of 1:1, see page 97: • A = LHD Right (left-hand drive, right lens) • B = LHD Left (left-hand drive, left lens) • C = RHD Right (right-hand drive, right lens) • D = RHD Left (right-hand drive, left lens) 2. Transfer the template to a self-adhesive waterproof material and cut it out. 3. Position the self-adhesive templates at the right distance from the edge of the head- lamp lens using the illustration, see page 96, and the dimensions in the fol- lowing list: • Template A: horizontal line approx. 80 mm, vertical line approx. 20 mm • Template B: horizontal line approx. 80 mm, vertical line approx. 4 mm • Template C: horizontal line approx. 120 mm, vertical line approx. 4 mm 03 Your driving environment Lighting • Template D: horizontal line approx. 85 mm, vertical line approx. 15 mm 03 `` 95 03 Your driving environment Lighting Aligning the templates 03 96 Upper row: left-hand drive cars, templates A and B. Lower row: right-hand drive cars, templates C and D. Templates for halogen headlamps 03 Your driving environment Lighting 03 97 03 Your driving environment Wipers and washing Windscreen wipers1 03 Continuous wiping The wipers sweep at normal speed. The wipers sweep at high speed. IMPORTANT Before activating the wipers during winter - ensure that the wiper blades are not frozen in and that any snow or ice on the wind- screen (and rear window) is scraped away. Windscreen wipers and windscreen washers. IMPORTANT Rain sensor, on/off Thumbwheel sensitivity/frequency Windscreen wipers off Move the stalk switch to position 0 to switch off the windscreen wipers. Single sweep Raise the stalk switch and release to make one sweep. Intermittent wiping Set the number of sweeps per time unit with the thumbwheel when inter- mittent wiping is selected. Use plenty of washer fluid when the wipers are cleaning the windscreen. The wind- screen must be wet when the windscreen wipers are operating. Service position wiper blade For cleaning the windscreen/wiper blades and replacement of wiper blades see see page 341 and 361. Rain sensor* The rain sensor automatically starts the wind- screen wipers based on how much water it detects on the windscreen. The sensitivity of 1 Replacing the wiper blades see page 341, service position, wiper blade see page 341 and filling washer fluid see page 343. 98 * Option/accessory, for more information, see Introduction. the rain sensor can be adjusted using the thumbwheel. When the rain sensor is activated a light in the button the rain sensor symbol is shown in the right-hand display in the combined instrument panel. Activating and setting the sensitivity When activating the rain sensor, the car must be running or the remote control key in position I or II while the windscreen wiper stalk switch must be in position 0 or in the position for a single sweep. Activate the rain sensor by pressing the button . The windscreen wipers make one sweep. Press the stalk switch up for the wipers to make an extra sweep. Turn the thumbwheel upward for higher sensi- tivity and downward for lower sensitivity. (An extra sweep is made when the thumbwheel is turned upward.) Deactivate Deactivate the rain sensor by pressing the but- ton another wiper program. or move the stalk switch down to The rain sensor is automatically deactivated when the remote control key is removed from the ignition switch or five minutes after the engine has been switched off. IMPORTANT The windscreen wipers could start and be damaged in an automatic car wash. Deac- tivate the rain sensor while the car is running or the remote control key is in position I or II. The symbol in the combined instrument panel and the lamp in the button go out. Washing the headlamps and windows Washing function. 03 Your driving environment Washing the windscreen Move the stalk switch toward the steering wheel to start the windscreen and headlamp washers. The windscreen wipers will make several more sweeps and the headlamps are washed once the stalk switch has been released. Heated washer nozzles* The washer nozzles are heated automatically in cold weather to prevent the washer fluid freezing solid. High-pressure headlamp washing* High-pressure headlamp washing consumes a large quantity of washer fluid. To save fluid, the headlamps are washed automatically at every fifth windscreen wash cycle. Reduced washing If only approx. 1 litre of washer fluid remains in the reservoir and the message that you should fill the washer fluid is shown in the combined instrument panel's display, then the supply of washer fluid to the headlamps is switched off. This is in order to prioritise cleaning the wind- screen and the visibility through it. Wipers and washing Wiping and washing the rear window 03 Rear window wiper – intermittent wiping Rear window wiper – continuous speed Press the stalk switch forward (see the arrow in the illustration above) to initiate rear window washing and wiping. NOTE The rear window wiper is equipped with overheating protection which means that the motor is switched off if it overheats. The rear window wiper works again after a cool- ing period (30 seconds or longer, depending on the heat in the motor and the outside temperature). * Option/accessory, for more information, see Introduction. 99 03 Your driving environment Wipers and washing Wiper – reversing Engaging reverse gear while the windscreen wipers are on initiates intermittent rear window wiping2. The function stops when reverse gear is disengaged. If the rear window wiper is already on at con- tinuous speed, no change is made. 03 NOTE On cars with rain sensor, the rear window wiper is activated with reversing, if the sen- sor is activated and it is raining. 2 This function (intermittent wiping when reversing) can be deactivated. Visit a workshop. Volvo recommends that you contact an authorised Volvo workshop. 100 General Heat-reflecting windscreen* Laminated glass The glass is reinforced which pro- vides better protection against break-ins and improved sound insu- lation in the passenger compartment. The windscreen and other windows* have lami- nated glass. 03 Your driving environment Windows, rearview and door mirrors windscreen with no heat-reflecting film (see the highlighted area in the above illustration). Power windows 03 Water and dirt-repellent coating* Windows are treated with a coating that improves the view in difficult weather conditions. Maintenance, see page 362. IMPORTANT Areas where IR film is not applied. Dimensions Do not use a metal ice scraper to remove ice from the windows. Use the defroster to remove ice from the mirrors, see page 104. 40 mm 80 mm The windscreen is equipped with a heat- reflecting film (IR) that reduces the solar heat radiation into the passenger compartment. The positioning of electronic equipment, such as a transponder, behind a glass surface with heat-reflecting film may affect its function and performance. For the optimal function of electronic equip- ment, it should be positioned on the part of the Driver's door control panel. Switch for electric child safety locks* and disengaging rear power window buttons, see page 62. Rear window controls Front window controls WARNING Check that none of the rear seat passengers is in danger of becoming trapped in any way when closing the windows from the driver's door. * Option/accessory, for more information, see Introduction. 101 03 Your driving environment Windows, rearview and door mirrors WARNING Operating Make sure that children or other passengers are not in danger of becoming trapped in any way when closing the windows, in par- ticular when the remote control key is used. 03 WARNING If there are children in the car - remember to always switch off the power supply to the power windows by selecting key position 0 and then take the remote control key with you when leaving the car. For information on key positions - see page 79. 102 Operating the power windows. Operating without auto Operating with auto All power windows can be operated using the control panel for the driver's door - the control panels for the other doors can only each oper- ate their respective power window. Only one control panel can be operated at a time. In order for the power windows to be used the key position must be at least I - see page 78. The power windows can be operated for a few minutes after the engine has been switched off and after the remote control key has been removed - although not after a door has been opened. Closing of the windows is stopped and the window is opened if anything prevents its movement. It is possible to override the pinch protection when closing has been interrupted, e.g. if there is ice forming. After two successive closing interruptions the pinch protection will be forced and the automatic function deacti- vated for a short while, now it is possible to close by continually holding the button pulled up. NOTE One way to reduce the pulsating wind noise when the rear windows are open is to also open the front windows slightly. Operating without auto Move one of the controls up/down gently. The power windows move up/down as long as the control is held in position. Operating with auto Move one of the controls up/down to the end position and release it. The window runs auto- matically to its end position. Operating with the remote control key and central locking To remotely operate the power windows from the outside with the remote control key or from inside with central locking, see pages 46 and 58. Resetting If the battery is disconnected then the function for automatic opening must be reset so that it can work correctly. 1. Gently raise the front section of the button to raise the window to its end position and hold it there for one second. 2. Release the button briefly. 3. Raise the front section of the button again for one second. WARNING Resetting must be carried out to ensure that pinch protection works. Door mirrors 03 Your driving environment Windows, rearview and door mirrors WARNING The mirror on the driver's side is the wide- angle type to provide optimal vision. Objects may appear further away than they actually are. Door mirror controls. Adjusting 1. Press the L button for the left-hand door mirror or the R button for the right-hand door mirror. The light in the button illumi- nates. 2. Adjust the position with the joystick in the centre. 3. Press the L or R button again. The light should no longer be illuminated. Storing the position1 The mirror positions are stored in the key mem- ory when the car has been locked with the remote control key. When the car is unlocked with the same remote control key the mirrors and the driver's seat adopt the stored positions when the driver's door is opened. The function can be activated/deactivated in the menu system MY CAR under Settings Car settings Personal settings in key memory. For a description of the menu system, see page 203. Angling the door mirror when parking1 The door mirror can be angled down for the driver to view the side of the road when parking for example. – Engage reverse gear and press the L or R button. Car key memory 1 Only in combination with power seat with memory, see page 81. When reverse gear is disengaged the mirror automatically returns to its original position 03 103 03 Your driving environment Windows, rearview and door mirrors 03 after approx. 10 seconds, or sooner by press- ing the L and R button. Automatic angling of the door mirror when parking1 When reverse gear is engaged the door mirror is automatically angled down so that the driver can see the side of the road when parking for example. When reverse gear is disengaged the mirror automatically returns to its original posi- tion after a short time. The function can be activated/deactivated in the menu system MY CAR under Settings Car settings left mirror or Tilt right mirror. For a descrip- tion of the menu system, see page 203. Automatic retraction when locking1 When the car is locked/unlocked with the remote control key the door mirrors are auto- matically retracted/extended. The function can be activated/deactivated in the menu system MY CAR under Settings Car settings Fold mirrors. For a description of the menu system, see page 203. Side mirror settings Side mirror settings Tilt Resetting to neutral Mirrors that have been moved out of position by an external force must be reset electrically to the neutral position for electric retracting/ extending to work correctly: 1. Retract the mirrors with the L and R but- tons. 2. Fold them out again with the L and R but- tons. 3. Repeat the above procedure as necessary. The mirrors are now reset in neutral position. Retractable power door mirrors* The mirrors can be retracted for parking/driving in narrow spaces: 1. Depress the L and R buttons simultane- ously (key position must be at least I). 2. Release them after approximately 1 second. The mirrors auto- matically stop in the fully retracted posi- tion. Fold out the mirrors by pressing down the L and R buttons simultaneously. The mirrors automatically stop in the fully extended posi- tion. Home safe and approach lighting The light on the door mirrors illuminates when approach lighting or home safe lighting is selected, see page 94. Rear window and door mirror defrosters Use the defroster to quickly remove misting and ice from the rear window and the door mir- rors. One press of the button starts the heating. The light in the button indicates that the function is active. Disconnect the heating as soon as the ice/misting is cleared in order not to load the battery unnecessarily. However, the heating is switched off automatically after a certain time. 1 Only in combination with power seat with memory, see page 81. 104 * Option/accessory, for more information, see Introduction. 03 Your driving environment Windows, rearview and door mirrors The door mirrors and rear window are demis- ted/defrosted automatically if the car is started in an outside temperature lower than +9 °C. Automatic defrosting can be selected in the menu system MY CAR under Settings Climate settings defroster. Select between On or Off. For a description of the menu system, see page 203. Automatic rear Interior rearview mirror dimming with the dimming control when lights from behind are distracting: 1. Use dimming by moving the control in towards the passenger compartment. 2. Return to normal position by moving the control towards the windscreen. Automatic dimming* Bright light from behind is automatically dimmed by the rearview mirror. The control is not available in mirrors with automatic dim- ming. The compass* can only be specified for rear- view mirrors with automatic dimming, see page 106. 03 Control for dimming Manual dimming Bright light from behind could be reflected in the rearview mirror and dazzle the driver. Use * Option/accessory, for more information, see Introduction. 105 03 Your driving environment Compass* Operation 03 Rearview mirror with compass. The upper right-hand corner of the rearview mirror has an integrated display that shows the compass direction in which the front of the car is pointing. Eight different directions are shown with English abbreviations: N (north), NE (north east), E (east), SE (south east), S (south), SW (south west), W (west) and NW (north west). The compass is activated automatically when the car is started or in key position II, see page 78. To deactivate/activate the compass - press in the button on the underside of the mir- ror using a paper clip for example. Calibration The earth is divided into 15 magnetic zones. The compass is set for the geographic area to which the car was delivered. The compass should be calibrated if the car is moved across several magnetic zones. Proceed as follows: 1. Stop the car in a large open area free from steel structures and high-voltage power lines. 2. Start the car. NOTE For optimum calibration - switch off all elec- trical equipment (climate control system, wipers etc.) and make sure that all doors are closed. 3. Hold the button on the underside of the rearview mirror depressed approx. 6 seconds (using a paper clip for example) until the character C is shown. 4. Hold the button on the underside of the rearview mirror depressed approx. 3 seconds. The number of the cur- rent magnetic zone is shown. 5. Press the button repeatedly until the required magnetic zone (1–15) is shown. See the map of magnetic zones for the compass. 6. Wait until the display resumes showing the character C. 7. Drive slowly in a circle at a speed of no more than 10 km/h until a compass direc- tion is shown in the display, indicating that calibration is complete. Then drive a further 2 circles to fine-tune calibration. 8. Repeat the above procedure as necessary. Magnetic zones. 106 * Option/accessory, for more information, see Introduction. 03 Your driving environment Open manually by pulling the control back- wards to the point of resistance for manual opening. The sunroof moves to maximum open position as long as the button is kept depressed. Closing Close manually by pushing the control for- wards to the point of resistance for manual closing. The sunroof moves to closed position as long as the button is kept depressed. WARNING Risk of crushing when sunroof is closed. The sunroof's pinch-protection function only operates during automatic closing, not manual. Close automatically by pressing the control to the position for automatic closing and then release it. The power supply to the sunroof is switched off by selecting key position 0 and removing the remote control key from the ignition switch. General The sunroof controls are located in the roof panel. The sunroof can be opened vertically at the rear edge and horizontally. Key position I or II is required for the sunroof to be opened. Horizontal opening Horizontal opening, backward/forward. Opening, automatic Opening, manual Closing, manual Closing, automatic Opening For maximum sunroof opening, move the con- trol back to the position for automatic opening and release. Power sunroof* WARNING If there are children in the car: Remember to always switch off the power supply to the sunroof by selecting key posi- tion 0 and then take the remote control key with you when leaving the car. For informa- tion on key positions - see page 79. 03 Vertical opening Vertical opening, raised at the rear edge. Open by pressing the rear edge of the con- trol upward. Close by pulling the rear edge of the con- trol down. * Option/accessory, for more information, see Introduction. 107 03 Your driving environment Power sunroof* Closing using the remote control key or central locking button 03 Pinch protection The sunroof's pinch protection function is trig- gered if it is blocked by an object during auto- matic closing. If blocked, the sunroof will stop and automatically open to the previous posi- tion. Wind deflector One long press on the lock button closes the sunroof and all the windows, see pages 45 and 58. The doors and the tailgate are locked. To interrupt closing, press the lock button again. WARNING If the sunroof is closed using the remote control key, check that no one is in danger of becoming trapped in any way. Sunscreen The sunroof features a manual, sliding interior sunscreen. The sunscreen slides back auto- matically when the sunroof is opened. Grip the handle and slide the screen forward to close it. The sunroof has a wind deflector that is folded up when the sunroof is in the open position. 108 * Option/accessory, for more information, see Introduction. General information on the alcolock The alcolock's1 function is to prevent the car from being driven by individuals under the influence of alcohol. Before the engine can be started the driver must take a breath test that verifies that he/she is not under the influence of alcohol. Alcolock calibration takes place in accordance with each market's limit value in force for driving legally. WARNING The Alcolock is an aid and does not exempt the driver from responsibility. It is always the responsibility of the driver to be sober and to drive the car safely. 03 Your driving environment Alcolock* Functions Operation Battery Alcolock indicator lamp (4) shows battery sta- tus: Indicator lamp (4) Green flashing Green Yellow Red Battery status 03 Charging in pro- gress Fully charged Semi-charged Discharged - fit the charger in the holder or connect the power supply cable from the glovebox. NOTE Store the Alcolock in its holder. This will keep the built-in battery fully charged and the Alcolock is activated automatically when the car is opened. 1. Nozzle for breath test. 2. Switch. 3. Transmission button. 4. Lamp for battery status. 5. Lamp for result of breath test. 6. Lamp indicates ready for breath test. 1 Also called Alcoguard. * Option/accessory, for more information, see Introduction. 109 03 Your driving environment Alcolock* Storage 03 Handheld unit storage and charging station. • The handheld alcolock unit is released by depressing it slightly in its holder and releasing it - it then springs out and can be removed from the holder. • Replace the handheld unit in the holder by pushing it in until it engages. • Store the handheld unit in the holder - this provides it with the best protection and keeps its batteries fully charged. Before starting the engine The Alcolock is activated automatically and is then ready for use when the car is opened. 1. When the indicator lamp (6) is green the Alcolock is ready for use. 2. Withdraw the Alcolock from its holder. If the Alcolock is outside the car when it is unlocked then it must first be activated with the switch (2). 3. Fold up the nozzle (1), take a deep breath and blow with an even pressure until a "click" is heard after approx. 5 seconds. The result will be one of the alternatives in the following table Result after breath test. If no message is shown then the transmis- sion to the car may have failed - in which case, press the button (3) to transmit the result to the car manually. 4. 5. Fold down the nozzle and refit the Alcolock in its holder. 6. Start the engine following an approved breath test within 5 minutes - otherwise it must be repeated. Result after breath test Indicator lamp (5) + Display text Specification Green lamp + Alco- guard Approved test Start the engine - no alcohol content measured. Yellow lamp + Alco- guard Approved test Red lamp + Disap- proved test Wait 1 minute Engine starting pos- sible - measured alcohol content is above 0.1 promille but below the limit value in forceA. Engine starting not possible - measured alcohol content is above the limit value in forceA. A Limits vary between countries, so find out what limits apply. See also the section entitled General information on the Alcolock on page 109 NOTE After a completed period of driving, the engine can be restarted within 30 minutes without a new breath test. 110 * Option/accessory, for more information, see Introduction. To bear in mind Before the breath test In order to obtain correct function and as accu- rate a measurement result as possible: • Avoid eating or drinking approx. 5 minutes before the breath test. • Avoid excess windscreen washing - the alcohol in the washer fluid may result in an incorrect measurement result. Change of driver In order to ensure that a new breath test is car- ried out in the event of a change of driver - depress the switch (2) and the send button (3) simultaneously for approx. 3 seconds. At which point the car returns to start inhibition mode and a new approved breath test is required before starting the engine. Calibration and service The Alcolock must be checked and calibrated at a workshop2 every 12 months. 30 days before recalibration is necessary the display shows Alcoguard Calibr. required. If calibration is not carried out within these 30 days then normal engine starting will be blocked - only starting with the Bypass func- 2 An authorised Volvo workshop is recommended. 03 Your driving environment Alcolock* tion will then be possible, see page 111 sec- tion Emergency situation. The message can be cleared by pressing the send button (3) once. Otherwise it goes out on its own after approx. 2 minutes but then reap- pears each time the engine is started - only recalibration at a workshop2 can clear the mes- sage permanently. In extremely cold weather the heating time can be reduced by taking the Alcolock indoors. Emergency situation In the event of an emergency situation or the Alcolock is out of order, it is possible to bypass the Alcolock in order to drive the car. 03 NOTE Cold or hot weather The colder the weather the longer it takes before the Alcolock is ready for use: All Bypass activation is logged and saved in memory, see page 8 in the section, Record- ing data. Temperature (ºC) Maximum heat- ing time (sec- onds) +10 to +85 -5 to +10 -40 to -5 10 60 180 At temperatures below -20 ºC or above +60 ºC the Alcolock requires additional power supply. The display shows Alcoguard insert power cable. In which case, connect the power supply cable from the glovebox and wait until indicator lamp (6) is green. After the Bypass function has been activated the display shows Alcoguard Bypass enabled the whole time while driving and can only be reset by a workshop2. The Bypass function can be tested without the error message being logged - in which case, carry out all the steps without starting the car. The error message is cleared when the car is locked. When the Alcolock is installed, either the Bypass or Emergency function is selected as the bypassing option. This setting can be changed afterwards at a workshop2. * Option/accessory, for more information, see Introduction. 111 03 Your driving environment 03 Alcolock* Activating the Bypass function • Depress and hold the left-hand stalk switch OK button and the button for haz- ard warning flashers simultaneously for approx. 5 seconds - the display first shows Bypass activated Wait 1 minute and then Alcoguard Bypass enabled - after which the engine can be started. This function can be activated several times. The error message shown during driving can only be cleared at a workshop2. Activating the Emergency function • Depress and hold the left-hand stalk switch OK button and the button for haz- ard warning flashers simultaneously for approx. 5 seconds - the display shows Alcoguard Bypass enabled and the engine can be started. This function can be used once, after which a reset must be made at a workshop2. Symbols and display messages In addition to the previously described mes- sages, the combined instrument panel's dis- play can also show the following: Display text Meaning/Action Alcoguard Blow harder Blowing too weak - blow harder. Heating not finished - wait for text Alco- guard Blow 5 sec- onds. Display text Meaning/Action Alcoguard wait Preheating Alcoguard Restart possible The engine has been switched off for less than 30 minutes - engine starting pos- sible without new test. Alcoguard Service required Contact a work- shop2. Alcoguard No sig- nal Transmission failed - send manually with button (3) or take a new breath test. Alcoguard Invalid test Test failed - take a new breath test. Alcoguard Blow longer Alcoguard Blow softer Blowing too short - blow for longer. Blowing too hard - blow more gently. 2 An authorised Volvo workshop is recommended. 112 * Option/accessory, for more information, see Introduction. Petrol and diesel engines Ignition switch with remote control key extracted/ inserted. and START/STOP ENGINE button. IMPORTANT Do not press in the remote control key incor- rectly turned - Hold the end with the detach- able key blade, see page 48. 1. Insert the remote control key in the ignition switch and press it in to its end position. Note that if the car is equipped with an alcolock then a breath test must first be approved before the engine can be started - see page 109. 03 Your driving environment Starting the engine 2. Hold the clutch pedal fully depressed1. (For cars with automatic gearbox - Depress the brake pedal.) 3. Press the START/STOP ENGINE button and then release it. The starter motor works until the engine starts or until its overheating protection triggers. NOTE The idling speed can be noticeably higher than normal for certain engine types during cold starting. This is so that the emissions system can reach normal operating tem- perature as quickly as possible, which min- imises exhaust emissions and protects the environment. 03 IMPORTANT If the engine fails to start after 3 attempts - wait for 3 minutes before making a further attempt. Starting capacity increases if the battery is allowed to recover. WARNING Never remove the remote control key from the ignition switch after starting the engine or when the car is being towed. WARNING Always remove the remote control key from the ignition switch when leaving the car, and make sure that the key position is 0 - in par- ticular if there are children in the car. For information on how this works - see page 79.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Volvo V60 Owners Manual