2010 Volvo S80 Owners Manual

Selecting a channel category 1. Select Sirius radio mode as described

above.

2. Press ENTER. 3. Use the up/down arrow keys to scroll

through the list of categories.

4. Press ENTER or the right arrow key to

select a category. > The first channel in the selected cate-

gory will then be played.

Audio system

NOTE

• The category ALL is default, which ena- bles you to scroll through the entire list of available satellite channels.

• The channel categories are automati-

cally updated several times a year. This takes approximately two minutes and will interrupt normal broadcasting. A message will be displayed while updat- ing is in progress. Information on chan- nel or feature updates is available at www.sirius.com.

Selecting a channel There are three ways of tuning in a channel: • Using the left and right arrow keys • By turning the tuning control • Through direct channel entry.

NOTE

• The numbers of skipped or locked

channels will not be displayed.

• If a channel is locked, the access code must be entered before the channel can be selected. See "Unlocking a channel" on page 143.

04

``

* Option/accessory, for more information, see Introduction.

141

04 Comfort and driving pleasure

Audio system

Direct channel entry The Sirius satellite channels are in numerical order throughout all of the categories. To access a channel directly: 1. Press MENU and scroll to Direct channel

entry.

2. Use the numerical keypad to enter the

channel's number.

04

3. Press ENTER. The radio will tune to this channel, even if it belongs to a category other than the currently selected one.

Scanning SCAN automatically searches through the list of satellite channels. The search will only be carried out in the selected category, see page 135 for more detailed information.

Storing a channel A total of 20 satellite channels can be stored; 10 channels each for Sirius 1 and 2, see page 135 for detailed information on storing channels. • A long press on one of the number keys stores the currently tuned channel on that key.

• A short press on a number key while the radio is in Sirius 1or 2 mode will tune to the preset satellite channel stored on that but- ton, regardless of the currently selected channel category.

142

will be alerted by a text message and an audi- ble signal. Press ENTER to listen to the song or EXIT to cancel. To activate/deactivate the song seek function: 1. Press MENU 2. Scroll to Song seek 3. Press ENTER to activate or deactivate the

function.

NOTE

When the song has ended, the radio will remain tuned to the channel on which the song was played.

Radio text The text that is displayed about the song that is currently playing can be changed. Use the AUTO button or the menu to display the Artist, Title, Composer, or switch radio text off.

Song Seek and Song Memory The Song Seek and Song Memory functions provide both audio and visual notification when Sirius is broadcasting your favorite songs. Song Seek enables you to store the name of the song for future advance notification when that song is being played. The Song Memory feature makes it possible to view all of the cur- rent songs that are stored in memory. Song memory Up to ten songs can be saved in the system's memory. 1. Press MENU. 2. Scroll to Add song to song mem. and follow the instructions shown in the dis- play.

If a new song is selected when the memory is full, you will be prompted to press ENTER to delete the last song on the list.

NOTE

The remaining songs in the list will move down one position, and the newly added song will be placed at the top of the list.

Song seek When a satellite radio channel plays one of the songs stored in the song memory, the listener

04 Comfort and driving pleasure

Advanced settings This menu function enables you to make set- tings on certain Sirius satellite radio functions. To access this menu: 1. Press MENU. 2. Scroll to the Sirius menu. 3. Select Advanced Sirius settings.

WARNING

Settings should be made when the vehicle is at a standstill.

The following settings can be made in the Sir- ius menu: • The list of saved songs can be displayed • Channel skip settings can be made • Channel lock settings can be made • The channel access code can be displayed

or changed

• Your Sirius ID can be displayed Skip options This function is used to remove a channel from the list of available channels.

Skipping a channel 1. Select CHANNEL SKIP LIST and press

ENTER.

2. Select a category in the list and press

ENTER.

3. Skip channels in the list presented by

pressing ENTER or right arrow key.

Unskip all channels This permanently removes all channels from the skip list and makes them available for selection. Temp. unskip all ch. This function will temporarily unskip all chan- nels and make them available for selection. The channels remain on the skip list and will again be skipped the next time the ignition is switched on.

Channel lock Access to specific channels can be restricted (locked). A locked channel will not provide audio, song titles, or artist information.

NOTE

All channels are initially unlocked.

7 The default code is 0000. If you have changed the code and forgotten it, see the section "If you have forgotten the access code."

Audio system

Locking a channel: 1. Select Sirius ID in the menu and select

LOCK OPTIONS and press ENTER.

2. Select CHANNEL LOCK LIST and press

ENTER

3. Enter the channel access code7 and press

ENTER.

4. Select a category in the list and press

ENTER.

5. Lock channels in the list presented by

pressing ENTER or right arrow.

The channel is now locked and a checked box will be displayed to indicate this. It will be nec- essary to enter the channel access code7 in order to listen to a locked channel.

Unlocking a channel A channel's access code7 is required to unlock a channel. Unlock all channels This permanently removes all channels from the locked list and makes them available for selection. Temp. unlock all ch. This function will temporarily unlock all chan- nels and make them available for selection. The channels remain on the locked list and will

04

``

143

04 Comfort and driving pleasure

04

Audio system

again be locked the next time the ignition is switched on. CHANGE CODE This function makes it possible to change the channel access code. The default code is 0000. To change the code: 1. Select CHANGE CODE and press

ENTER.

2. Enter the current code and press ENTER. 3. Enter the new code and press ENTER. 4. Confirm the new code and press ENTER. If an incorrect code is entered, the text WRONG CODE! is displayed. If you have forgotten the access code: 1. Select SIRIUS ID in the Sirius settings

menu and press ENTER.

2. Press and hold the ENTER button for

2 seconds.

3. The current code will be displayed. Your Volvo retailer can also provide you with assistance. SIRIUS ID This function displays the 12-digit Sirius acti- vation ID.

8 Certain markets only.

CD functions

Playing a CD (CD changer) If a CD position with a music CD is already selected when CD is pressed, it will be played automatically. Otherwise select a disc with the on the naviga- number buttons 1 – 6 or tion button.

Insert a CD (CD changer) 1. Select an empty position with the number on the navigation

buttons 1 – 6 or button. > An empty position is marked on the dis- play. The text Insert disc shows that a new disc can be inserted. The CD changer can hold up to six CDs. Insert a CD in the CD changer slot.

Center console, controls for CD functions

CD insert and eject

CD slot

2.

Navigation button for changing CD tracks

Fast-back and change CD track

CD changer* position selection

Scan CD

Playing a CD (CD player8) If a music CD is in the player when CD is pressed, it will be played automatically. Other- wise, insert a disc and press CD.

Disc eject For reasons of traffic safety, an ejected CD must be removed within 12 seconds or it will be automatically drawn back into the slot and the CD player will enter pause mode. Press the CD button to restart the disc. Eject individual discs by pressing the eject but- ton. Eject all discs with a long press on the eject button. The entire magazine is emptied disc by disc.

144

* Option/accessory, for more information, see Introduction.

04 Comfort and driving pleasure

NOTE

The Eject all function can only be used while the vehicle is at a standstill and will be can- celled if the vehicle begins to move.

Pause When the audio system volume is turned off completely, the CD player will pause and will resume playing when the volume is turned up again.

Sound files In addition to playing normal music CDs, the CD player/changer can also play discs con- taining files in mp3 or wma format.

NOTE

Some copy protected sound files may not be read by the player.

When a CD containing sound files is inserted into the player the disc's directory structure is scanned before the CD begins playing. The length of time that this takes depends on the quality of the disc. Navigating the disc and playing tracks If a disc containing sound files is inside the CD player, press ENTER to display the disc's directory structure. The directory structure is navigated in the same way as the audio sys-

tem's menu structure. Sound files have the

symbol and directories have the

symbol. Press ENTER to play a selected folder or a file. When the music file has been played, the player will continue to play the rest of the files in the current folder. When all of the files in the folder have been played, the player will auto- matically go to the next folder and play the files in it.

on the navigation button

Fast-forward/change CD tracks and sound files Short presses are used to scroll between CD tracks/sound files. Long presses are used to search within CD tracks/sound files. TUNING (or the steering wheel keypad) can also be used for this pur- pose.

Scan CD This function plays the first ten seconds of each CD track/sound file. Press SCAN to acti- vate. Interrupt with EXIT or SCAN to continue playing the current CD track/sound file.

Random This function plays the tracks in random order (shuffle). The random CD tracks/sound files can be scrolled through in the normal way.

Audio system

NOTE

It is only possible to scroll between random CD tracks on the current disc.

Different messages are displayed depending on which random function has been selected: • RANDOM means that the tracks from only

one music CD are played

• RND ALL means that all tracks on all

music CDs in the optional CD changer are played.

• RANDOM FOLDER means that the sound

files in a directory on the current CD are played. CD player If a normal music CD is being played, activate/ deactivate under Random. If a disc with sound files is being played, acti- vate/deactivate under Random Folder. CD changer If a normal music CD is being played under Random Single disc or Random All discs. The All discs feature only applies to the music CDs in the changer. If a CD with sound files is being played, acti- vate/deactivate instead under Random Folder. If you select another CD the function is deactivated.

04

``

145

04 Comfort and driving pleasure

Audio system

Disc text If title information is stored on a music CD it can be shown on the display9. Activate/deactivate Disc text. in CD mode under CD settings

04

9 Only applies to the CD changer.

146

04 Comfort and driving pleasure

and other controls on the cell phone can always be used regardless of whether or not the phone is connected to the hands-free sys- tem.

NOTE

Not all cell phones are fully compatible with the hands-free system. A list of compatible phones is available at your Volvo retailer or at www.volvocars.us

WARNING

Never use the hands-free feature or any other device in your vehicle in a way that distracts you from the task of driving safely. Distraction can lead to a serious accident.

Introduction

System overview Cell phone

Location of the microphone

Steering wheel keypad

Center console control panel and display

Bluetooth® hands-free This feature makes it possible to set up a wire- less connection between a Bluetooth(cid:159)-ena- bled cell phone and the vehicle’s audio system. This enables the audio system to function as a hands-free connection and allows you to remote-control a number of the phone’s func- tions. The microphone used by this system is located in the ceiling console (2). The buttons

Bluetooth® hands-free connection

Bluetooth® functions in the center console control panel

VOLUME – This function is also available on the steering wheel keypad. Keys containing letters and numbers for dialing numbers, adding phone book entries, etc. PHONE – Press to activate/deactivate the Bluetooth® function Navigation buttons

EXIT – Press to end or defer calls, erase characters that have been entered, end an ongoing function. This function is also available on the steering wheel keypad. ENTER – Answer a call. Press once to dis- play the most recently dialed number. This

04

``

147

04 Comfort and driving pleasure

Bluetooth® hands-free connection

function is also available on the steering wheel keypad.

Getting started Use the controls on steering wheel keypad (3) and in the center console (4) to access, navi- gate and make selections in the hands-free system’s menus (see page 152).

Activating/deactivating A short press on the PHONE button in the cen- ter console activates the hands-free system. The text TELEPHONE will appear at the top of the display to indicate that the audio system is in telephone mode.

symbol indicates that the hands-free

The system is active. A long press on the PHONE button deactivates the hands-free system and disconnects the cell phone.

Connecting cell phones The procedure for connecting a cell phone var- ies, depending on the phone itself, and on whether or not the phone has been previously connected. If this is the first time the phone is to be con- nected to the hands-free system, proceed as follows:

04

148

Alternative 1–using the vehicle's menus 1. Activate the cell phone’s Bluetooth® func- tion (refer to the phone’s owner’s manual if necessary) or go to www.volvocars.com 2. Activate the vehicle’s Bluetooth® hands-

free system by briefly pressing the PHONE button. > Add phone will be displayed. If one or more cell phones are already registered in the system, they will also be dis- played.

3. Select Add phone.

> The audio system will search for cell phones that are in range. This search takes approximately 30 seconds. Any phones detected will be displayed with their Bluetooth® names. The hands-free system’s Bluetooth® name will appear in the cell phone’s display as My Car. 4. Select one of the cell phones shown in the

audio system’s (center console) display. 5. Using the cell phone’s keypad, enter the

digits shown in the audio system’s display.

Alternative 2–using the cell phone’s menus 1. Activate the hands-free system by briefly pressing the PHONE button in the center console. If there is a cell phone connected,

disconnect it from the hands-free system (by pressing PHONE in the center console for several seconds).

2. Perform a search using the cell phone’s

Bluetooth® function (consult the cell phone’s owner’s manual if necessary).

3. Select My Car in the list of devices shown

in the cell phone’s display.

4. When prompted, enter the PIN code 1234

in the cell phone.

5. Connect to My Car from the cell phone. The cell phone will be registered and will be connected automatically to the audio system while the text Synchronising is displayed. For more information on synchronizing a cell phone, see page 150. When a connection has been established, the

symbol and the cell phone’s Bluetooth® name will be displayed. The cell phone can now be controlled from the audio system.

Making a call 1. Ensure that TELEPHONE is shown at the top of the center console display and that the symbol is visible (by pressing briefly on PHONE on the center console).

2. Dial the desired phone number or use the

phone book (see page 150).

04 Comfort and driving pleasure

3. Press ENTER. End the call by pressing EXIT.

Disconnecting the cell phone The cell phone is automatically disconnected from the audio system if it is moved out of range. For more information about connec- tions, see page 148. The cell phone can be manually disconnected from the hands-free system by pressing PHONE. The hands-free system is also deac- tivated when the ignition is switched off (or if the driver’s door is opened on vehicles equip- ped with the optional keyless drive). When the cell phone is disconnected from the hands-free system, a call in progress can be continued using the cell phone’s own speaker and microphone.

NOTE

Certain cell phones may require confirma- tion from the phone’s keypad when a call is transferred from hands-free to the cell phone.

Handling calls

Incoming calls ± Press ENTER to answer a call, even if the audio system is currently in e.g., CD or FM mode.

± Press EXIT to defer a call.

Automatic answer This function means that incoming calls will be answered automatically. Activate or deactivate the function in the menu system under Phone settings answer.

Call options

Automatic

Call settings While a call is in progress, press MENU or ENTER on the center console to access the following functions: • Microphone off–mute the audio system’s

microphone.

• Transfer call to mobile–transfer the call

from hands-free to the cell phone.

• Phone book–this feature enables you to

search for a stored telephone number.

Bluetooth® hands-free connection

NOTE

• On certain cell phones, the connection

is broken when the mute function is used, which is normal. If this happens, the hands-free system will prompt you to reconnect.

• A new call cannot be initiated while

another call is in progress.

Sound settings

04

Call volume Call volume can be adjusted when the hands- free system is activated. Use the buttons in the steering wheel keypad or the audio system’s volume control.

Audio system volume While a phone call is in progress, volume for the audio system can be adjusted in the normal way with the audio system's volume control. In order to adjust volume during a phone call, the audio system must be switched to one of the other modes (FM, CD, etc). Audio system sound can be automatically muted when a phone call is received in Phone settings radio and adjust the volume with the keys on the center console.

Sounds and volume Mute

``

149

04 Comfort and driving pleasure

Bluetooth® hands-free connection

Ringing volume Go to Phone settings

Sounds and volume

Ring volume and adjust the volume with

the

keys on the center console.

Ringing tones The hands-free system’s integrated ringing tones can be selected in Phone settings Sounds and volume signal 1,2,3....

Ring signal

Ring

04

NOTE

The connected cell phone’s ring tone is not switched off when one of the hands-free system's ringing tones is used.

If you prefer to use the connected cell phone’s ring tone1, go to Phone settings and volume phone signal

Sounds Use mobile

Ring signal

1 Not supported by all cell phones.

150

More information about registering and connecting cell phones A maximum of 5 cell phones can be registered in the hands-free system. Registration only needs to be done once for each phone. After registration, the cell phone no longer needs to be in sight or searchable. Only one cell phone can be connected to hands-free at a time. Phones can be unregistered in Bluetooth Remove telephone

Automatic connection When the hands-free system is active and the most recently connected cell phone is within range, it is detected automatically. When the audio system searches for the most recently connected phone, this phone’s name appears in the display. To manually connect a different cell phone, press EXIT.

Manual connection To connect a phone other than the one that was most recently connected or to switch between cell phones that are already regis- tered in the hands-free system: 1. Put the audio system in telephone mode. 2. Press PHONE in the center console and

select one of the phones on the list.

A connection can also be established in the menu system under Bluetooth Connect phone or Change phone.

Phone book In order to use the hands-free system’s phone book (list of contacts), TELEPHONE must be displayed at the top of the center console dis- play and the

symbol must be visible.

The audio system stores a copy of the phone book of each registered cell phone. The phone book is automatically copied each time a phone is connected. This function can be acti- vated in Phone settings phone book. Searches for contacts are only made in the phone book of the currently con- nected cell phone.

Synchronise

NOTE

If a particular cell phone does not support copying of the phone book, List is empty will be displayed when copying has been completed.

If the phone book contains information about someone who is trying to call you, this infor- mation will be shown in the display.

Searching for contacts The easiest way to search for a contact in the phone book is to press and hold any of the buttons 2–9 (see the illustration on page 147). This starts a search based on the first letter on the button that has been pressed. The phone book can also be accessed by pressing the navigation buttons on the center console or by pressing steering wheel keypad. A search can also be made in the phone book’s search menu in Phone book 1. Enter the first letter of the contact’s name and press ENTER or simply press ENTER.

Search:

on the

2. Select the desired contact and press ENTER to make a call to that person.

Voice control If the cell phone that is currently connected allows calls to be made via voice commands, this function can be used by pressing and hold- ing ENTER.

Voice mail number The phone number to your voice mail can be changed in the menu Phone settings Call Voice mail number. If no number options has been stored, this menu can be accessed by a prolonged press on button 1. Once a

04 Comfort and driving pleasure

Bluetooth® hands-free connection

phone number has been stored, press and hold 1 to dial this number.

Button Function

Call lists Lists of calls in a particular cell phone are cop- ied to the hands-free system each time that phone is connected. These lists are then upda- ted while the phone is connected. Press ENTER to show the most recently dialed num- bers. Other call lists can be found under Call register.

NOTE

Certain cell phones display the list of the most recently dialed numbers in reverse order.

Entering text Text is entered by using the number buttons in the center console. Press a button once to enter the first letter on the button, twice to enter the second letter, etc. Continue to press the button to display other characters. Press EXIT briefly to erase a character. Press and hold EXIT to erase all of the characters that buttons on have been entered. Use the the center console to navigate among the char- acters.

Space .1-? ! , : " ' ( )

A B C 2 Ä Å À Æ Ç

D E F 3 È É

G H I 4 Ì

J K L 5

M N O 6 Ñ Ö Ò Ø

P Q R S 7 ß

T U V 8 Ü Ù

W X Y Z 9

Press briefly if two characters are to be entered in succession from the same button.

+ 0 @ * # & $ £ / %

Shift between uppercase and lowercase letters

04

``

151

04 Comfort and driving pleasure

Bluetooth® hands-free connection

Bluetooth® menus Missed calls 1. 2. Received calls Dialed calls Phone book 4. 4.1. 4.2. Bluetooth... 5.1. 5.2. 5.3. 5.4. Phone settings 6.1.

5.

6.

Search Copy fr. mobile phone

Change phone Connect phone Disconnect phone Connect fr. mobile phone

Call options 6.1.2. Automatic answer 6.1.3. Voice mail number Sounds and volume IDIS Synchronize phone book

6.2. 6.3. 6.4.

04

152

04 Comfort and driving pleasure

Introduction

Functions

NOTE

If a warning message appears while you are using the trip computer, this message must be acknowledged in order to return to the trip computer function. Acknowledge a message by pressing READ.

To change the unit of measure specified for distance and speed, contact an authorized Volvo workshop.

Information display and controls

READ–press to acknowledge/confirm/ erase a message) Thumb wheel (used to scroll among the trip computer menus) RESET–resets certain functions

To scroll through trip computer information, move the thumb wheel up or down. Continue turning to return to the starting point.

Average speed The system calculates the average speed from the last resetting. Reset using RESET.

Current speed in mph (Canadian models only) This function provides the driver with an instan- taneous conversion of the car's current speed from km/h to mph.

Current speed in km/h (U.S. models only) This function provides the driver with an instan- taneous conversion of the car's current speed from mph to km/h.

Current fuel consumption (Instantaneous) Current fuel consumption is calculated every second. The information on the display is

Trip computer

updated every few seconds. When the vehicle is stationary, "----" appears on the display.

Average fuel consumption The average fuel consumption since the last reset. Reset using RESET.

Driving distance on current fuel reserve This function shows the approximate distance that can be driven on the fuel remaining in the tank. The calculation is based on average fuel consumption during the last 20 miles (30 km) of driving and the amount of fuel remaining in the tank when the reading was taken. When the message ---- miles to empty tank appears in the display, refuel as soon as possible.

NOTE

The actual distance that can be driven on the usable fuel remaining in the tank may be influenced by a change in driving style.

See also page 196 for information on driving economically. Resetting 1. Select Average speed or Average fuel

consumption.

2. Press and hold RESET for approx. 1 sec-

ond to reset the selected function. If RESET is kept depressed for at 3 three

04

``

153

04 Comfort and driving pleasure

Trip computer

seconds, Average speed and Average fuel consumption are reset simultaneously.

04

154

04 Comfort and driving pleasure

Operation

Rearview mirror with compass. The rearview mirror has an integrated display that shows the compass direction in which the vehicle is pointing. Eight different directions are shown with the abbreviations: N (north), NE (north east), E (east), SE (southeast), S (south), SW (southwest), W (west) and NW (northwest). The compass is displayed automatically when the vehicle is started or in ignition mode II. To switch the compass on/off use a pen or similar object and press in the button on the rear side of the mirror.

Calibration The compass may need to be calibrated if, for example, the vehicle is driven into a new mag-

netic zone. The character C is shown in the mirror's display if calibration is necessary. 1. Stop the vehicle in a large open area, safely out of traffic and away from steel structures and high-tension electrical wires.

2. Start the vehicle.

NOTE

For best results from calibration, switch off all electrical equipment in the vehicle (cli- mate system, windshield wipers, audio sys- tem, etc.) and make sure that all doors are closed.

3. Using a pen or similar object, press and hold the button on the rear side of mirror until C is shown again in the mirror(after approx. 6 seconds).

4. Drive as usual. C disappears from the dis-

play when calibration is complete. Alternative calibration method: Drive slowly in a circle at a speed of no more than 5 mph (8 km/h) until C disap- pears from the display when calibration is complete.

Selecting a magnetic zone

Compass

15

14

13

12

11

10

04

Magnetic zones. The earth is divided into 15 magnetic zones. The correct zone must be selected for the com- pass to work correctly. 1. Put the ignition in mode II. 2. Using a pen or similar object, press and hold the button on the rear side of mirror for at least 3 seconds. The number for the current area will be shown.

3. Press the button repeatedly until the num-

ber for the required geographic area (1 – 15) is shown.

4. The display will revert to showing the com-

pass direction after several seconds.

155

04 Comfort and driving pleasure

Stability system

Introduction The Dynamic Stability and Traction Control system (DSTC) consists of a number of func- tions designed help reduce wheel spin, coun- teract skidding, and to generally help improve directional stability.

CAUTION

A pulsating sound will be audible when the system is actively operating and is normal.

Traction control (TC) This function is designed to help reduce wheel spin by transferring power from a drive wheel that begins to lose traction to the wheel on the opposite side of the vehicle (on the same axle). TC is most active at low speeds. This is one of DSTC's permanent functions and cannot be switched off.

Active Yaw Control (AYC) This function helps maintain directional stabil- ity, for example when cornering, by braking one or more of the wheels if the vehicle shows a tendency to skid or slide laterally. This is one of DSTC's permanent functions and cannot be switched off.

04

156

Spin control (SC) The spin control function is designed to help prevent the drive wheels from spinning while the vehicle is accelerating. Under certain circumstances, such as when driving with snow chains, or driving in deep snow or loose sand, it may be advisable to temporarily switch off this function for maxi- mum tractive force.

WARNING

The car's handling and stability characteris- tics will be altered if the spin control function has been disabled.

Operation

Temporarily switching off Spin control 1. Turn the thumbwheel until the DSTC

menu is shown.

2. Hold down the RESET button

to toggle

between DSTC SPIN CONTROL ON or OFF.

Messages in the information display DSTC Temporarily OFF – system function has been temporarily reduced due to high brake disc temperature. The function is acti- vated automatically when the brakes have cooled. DSTC Service required – the system has been disabled due to a fault. If this occurs: 1. Stop the vehicle in a safe place and turn off

the engine.

2. Restart the engine. If the message remains when the engine is restarted, drive to an authorized Volvo work- shop to have the system inspected.

Symbols in the instrument panel If the symbols at the same time, read the message in the information display.

and

are displayed

If the symbol appear as follows:

appears alone, it may

• If the symbol flashes, this indicates that the

stability system is actively functioning to help counteract wheel spin and/or a skid. • If the symbol remains on for approximately

2 seconds after the engine has been started, this indicates that the system is performing a self-diagnostic test.

WARNING

The stability system is intended to help improve driving safety. It supplements, but can never replace, the driver's judgment and responsibility when operating the vehi- cle. Speed and driving style should always be adapted to traffic and road conditions.

04 Comfort and driving pleasure

Stability system

04

157

04 Comfort and driving pleasure

04

Active chassis system–Four C

Active chassis (Four C)* Active chassis, Four-C (Continuously Con- trolled Chassis Concept), regulates the cha- racteristics of the shock absorbers so that the car's driving characteristics can be adjusted. There are three settings: Comfort, Sport and Advanced.

Comfort Comfort mode offers a somewhat softer ride and the transmission shifts gears at lower rpm. This mode is particularly suitable for long-dis- tance highway driving. The indicator light in the button will be on when this mode is selected.

Sport In this mode, the vehicle's body sway is reduced during cornering and steering response is more immediate. The transmission shifts up at higher rpm for sportier driving. The indicator light in the button will be on to indi- cate that Sport mode has been selected.

Advanced In this mode, body sway in curves is minimal and steering response is very direct. Gear shift- ing is done at high rpm in each gear for dynamic and active driving.

Operation

NOTE

This steering force level menu function can- not be accessed when the vehicle is in motion.

Chassis settings Use the buttons in the center console to change setting. The setting in use when the engine is switched off is activated the next time the engine is started.

Speed-dependent steering force* Steering force increases with the speed of the vehicle to give the driver enhanced sensitivity. At low speed the vehicle is easy to steer in order to facilitate parking, etc. Steering force can be changed under Car settings description of the menu system, see page 122.

Steering force level. For a

158

* Option/accessory, for more information, see Introduction.

04 Comfort and driving pleasure

Operation

Steering wheel-mounted controls and display

Standby mode

Resume set speed

Deactivating

Activate/set speed

Set speed indicator (parentheses indicate standby mode)

Engaging the cruise control function Before a speed can be set, the cruise control system must be engaged (put in standby mode). ± Press the CRUISE button (1).

> The symbol

illuminates and the text (---) mph (5) indicates that cruise con- trol is in standby mode.

NOTE

This does not set the vehicle's speed.

Setting a speed Use the buttons set the vehicle's cur- rent speed. The set speed is shown in the dis- play.

or

NOTE

Cruise control cannot be engaged at speeds below 20 mph (30 km/h).

Adjusting the set speed After a speed has been set, it can be increased or decreased by using the 1. Press and hold down

buttons.

until the

or

or

vehicle reaches the desired speed. > This will become the set speed when the

button is released.

2. Press

or

for approximately a half

second and release the button to increase or decrease vehicle speed by approxi- mately 1 mph (1.6 km/h).

Cruise control

NOTE

• A temporary increase in speed by

pressing the accelerator pedal, for less than 1 minute (e.g. when passing another car), does not affect the current cruise control setting. The vehicle will automatically return to the previously set speed when the accelerator pedal is released.

• If one of the cruise control buttons is kept depressed for more than approx. 1 minute cruise control is disengaged. The engine must then be switched off in order to reset cruise control.

Automatic deactivation Cruise control is automatically deactivated temporarily if one of the following occurs: • If the speed drops below approximately

20 mph (30 km/h).

• When the brake pedal is depressed. • If the gear selector is moved to position N. • During wheel spin or wheel lock-up. • If the vehicle's speed is increased by using

the accelerator pedal for more than 1 minute.

The currently set speed will be saved in the system's memory.

04

``

159

04 Comfort and driving pleasure

Cruise control

Temporary deactivation The driver can temporarily deactivate cruise control by pressing 0. The saved speed is shown in brackets in the information display.

Resume set speed If cruise control has been deactivated tempo- rarily, it can be reactivated by pressing . The vehicle's speed returns to the most recently set speed.

04

WARNING

There may be a significant increase in speed after the

button has been pressed.

Deactivation Cruise control is disengaged with CRUISE, by putting the gear selector in Neutral, or by switching off the engine. The set speed is cleared.

WARNING

Cruise control should not be used in heavy traffic or when driving on wet or slippery roads. Cruise control may not maintain set speed on steep downgrades.

160

04 Comfort and driving pleasure

Introduction Collision Warning with Auto-brake is designed to assist the driver if there is a risk of a collision with the vehicle ahead, if that vehicle is at a standstill or moving in the same direction as your vehicle. Auto-brake helps reduce the col- lision speed. Collision Warning consists of the following three functions: • Collision warning warns the driver of the

imminent risk of a collision.

• Brake support helpsthe driver brake effi-

ciently in a critical situation.

• Auto-brake brakes the vehicle automati-

cally if a collision cannot be avoided.

WARNING

The auto-brake function cannot prevent a collision but instead is intended to reduce speed at the moment of impact. For full braking effect, driver must apply the brakes.

WARNING

• The collision warning system does not work in all driving situations, and traffic, weather and road conditions.

• The collision warning system is not

designed to detect pedestrians.

• Warnings are only provided when the risk of collision is high. The Function section provides information about lim- itations that the driver must be aware of before use.

• Never wait for a collision warning. This system is designed to be a supplemen- tary driving aid. It is not, however, intended to replace the driver's atten- tion and judgement. The driver is responsible for maintaining a safe dis- tance and speed, even when the colli- sion warning system is in use.

• Maintenance of the collision warning

system components must only be per- formed by a trained and qualified Volvo technician.

Collision warning with Auto-brake*

Function

04

Function overview

Visual warning signal, collision risk

Radar sensor

Camera

Collision warning The radar sensor and the camera work together to detect stationary vehicles and vehi- cles that are moving in the same direction as your vehicle. If there is a risk of collision, the driver is alerted by a flashing red warning light and an audible warning signal. Collision warn- ing is active at speeds above 5 mph (7 km/h).

Brake support If the risk of collision continues to increase after the collision warning has been given, brake

* Option/accessory, for more information, see Introduction.

161

``

04 Comfort and driving pleasure

Collision warning with Auto-brake*

04

support is activated. Brake support prepares the brake system to react quickly, and the brakes are applied slightly. This may be expe- rienced as a light tug. If the brakes are applied quickly, full braking effect will be provided, even if pressure on the brake pedal is light.

Auto-brake If a collision is imminent and the driver has not applied the brakes, the auto-brake function is activated without the driver pressing the brake pedal. Limited brake force is applied to reduce the vehicle’s speed when the collision occurs.

WARNING

The auto-brake function cannot prevent a collision but instead is intended to reduce speed at the moment of impact. For full braking effect, driver must apply the brakes.

NOTE

The auto-brake function is always on and cannot be turned off.

Operation Some settings are controlled from the center console via a menu system. For information on how the menu system is used, see page 122.

On and off To switch Collision Warning on or off, go into the menu Car settings Collision warning settings and select On or Off. When the engine is started, the setting that was selected when it was switched off will be used.

Activating/deactivating warning signals The collision warning system’s audible and vis- ual signals are activated automatically when the engine is started if the collision warning system is activated. The audible warning signal can be activated/ deactivated by selecting the alternative On or Off in Car settings settings Warning sound.

Collision warning

Setting a warning distance This setting determines the distance at which the visual and audible warnings are triggered. Select Long, Normal or Short under Car settings Collision warning settings Warning distance The warning distance determines the level of sensitivity used by the system. The warning distance Long provides an earlier warning. Begin by using Long and if the system gives too many warnings, try changing to Normal.

WARNING

• The setting Short should only be used

in situations where traffic is light and moving at low speeds.

• Collision Warning alerts the driver to the risk of a collision but this function can- not reduce the driver’s reaction time.

• For Collision Warning to be as effective as possible, it is recommended that Dis- tance Alert be set to 4 or 5, see page 174.

NOTE

• When adaptive cruise control is used, the warning light and signal will be used by cruise control, even if they have been deactivated by the driver.

• In situations where traffic is moving at considerably different speeds, or if the vehicle ahead brakes suddenly, warn- ings may be considered to be late, even if the setting Long has been selected.

Checking settings The current Collision Warning settings can be checked by going into the menu system at Car Collision warning settings. See settings page 122 for more information on the menu system.

162

* Option/accessory, for more information, see Introduction.

Limitations Strong sunlight, reflections, extreme light con- trasts, the use of sunglasses, or if the driver is not looking straight ahead may make the visual warning signal in the windshield difficult to see. For this reason, always activate the audible warning signal in such conditions.

NOTE

The visual warning signal may be temporar- ily disengaged in the event of high passen- ger compartment temperature due to strong sunlight, etc. If this occurs, the audible warning signal will be used, even if it has been deactivated in the menu system.

Warnings may not appear if the distance to the vehicle ahead is very small or if steering wheel and pedal movements are great, for example, due to a very active driving style.

04 Comfort and driving pleasure

Collision warning with Auto-brake*

WARNING

NOTE

If warnings are given too frequently, the warning distance can be reduced (see page 162. This causes the system to pro- vide later warnings, which decreases the total number of warnings provided.

The camera’s limitations The camera is used by Collision Warning with Auto-brake, Driver Alert Control (see page 177), and Lane Departure Warning (see page 180).

04

NOTE

• To help protect the camera in very hot

conditions, it may be temporarily switched off for approximately 15
minutes after the engine has been started.

• Keep the section of the windshield in

front of the camera clean and free of ice, snow, or condensation.

• In certain situations, the system cannot

provide warnings or warning may be delayed if traffic conditions or other external factors make it impossible for the radar sensor or camera to detect the vehicle ahead.

• Warnings may not be provided if the distance to the vehicle ahead is short, or if movements of the steering wheel/ brake pedal are great, such as during active driving.

• The sensor system has a limited range for stationary or slow-moving vehicles and may therefore give delayed or no warnings if your vehicle’s speed is above approximately 45 mph (70 km/h).

• Warnings for stationary or slow-moving

vehicles may not be provided in dark conditions.

The Collision Warning system uses the same radar sensors as Adaptive Cruise Control. For more information on the radar sensor and its limitations, see page 170. If no warning is given, or if a warning is delayed, Auto-brake will also not be provided or will be delayed.

* Option/accessory, for more information, see Introduction.

163

``

04 Comfort and driving pleasure

Collision warning with Auto-brake*

Fault tracing and actions If the message Windshield sensors blocked is displayed, this means that the cam- era is obscured and cannot detect vehicle or road marker lines in front of the vehicle. This, in turn, means that Collision Warning with Auto-brake, Lane Departure Warning, and Driver Alert Control will not have full function- ality. The table lists possible causes for this mes- sage being displayed, and suitable actions.

04

WARNING

• The camera has the same limitations as

the human eye. In other words, its “vision is impaired” by adverse weather conditions such as heavy snowfall, dense fog, etc. These conditions may reduce the function of systems that depend on the camera or cause these systems to temporarily stop function- ing.

• Never place any objects, decals, etc., on the windshield in front of the camera. This could reduce or block the camera’s function, and could cause one or more of the systems that utilize the camera to stop functioning.

• Strong sunlight, reflections from the

road surface, ice or snow covering the road, a dirty road surface, or unclear lane marker lines may drastically reduce the camera’s capacity to detect the side of a lane or another vehicle.

Cause

Action

The surface of the windshield in front of the camera is dirty or covered with ice or snow.

Fog, heavy rain or snow is interfering with the function of the camera.

Clean or clear the section of the windshield in front of the camera.

No action possible. Heavy precipitation may affect the function of the camera.

164

* Option/accessory, for more information, see Introduction.

04 Comfort and driving pleasure

Collision warning with Auto-brake*

Cause

Action

The surface of the windshield is clean but the message remains in the display.

Wait a short time. It may take several minutes for the camera to register visibility.

The surface between the inside of the windshield and the camera is dirty. Contact an authorized Volvo retailer or service technician to have this

surface cleaned.

Symbols and messages in the display

Symbol Message

Description

Collision warn. OFF

Collision warn. Unavailable

Auto braking was activated

Camera blocked See manual

Collision Warning is switched off. This message is displayed when the engine is started and will dis- appear after approx. 5 seconds. It can also be erased by pressing the READ button.

04

Collision Warning cannot be activated. This message is displayed when the driver attempts to activate the function. It will disappear after approx. 5 seconds or can be erased by pressing the READ button.

Auto-braking has been active.

The camera is temporarily not functioning. This message is displayed if the camera is obstructed by snow, ice, dirt, etc., on the windshield. Clean the area of the windshield in front of the camera, see page 163 for more information on the camera’s limitations.

* Option/accessory, for more information, see Introduction.

165

``

04 Comfort and driving pleasure

Collision warning with Auto-brake*

Symbol Message

Description

Radar blocked See manual

Collision warn. Service required

Collision Warning and Auto-brake are temporarily not functioning. The radar sensor is blocked, for example by heavy rain or snow that has accumulated in front of the sensor, and cannot detect other vehicles, see page 170 for more information on the radar sensor’s limitations.

Collision Warning and Auto-brake are partially or completely not functioning. Contact a trained and qualified Volvo service technician if the message remains in the display.

04

166

* Option/accessory, for more information, see Introduction.

04 Comfort and driving pleasure

Introduction Adaptive Cruise Control (ACC) is an optional system designed to assist the driver by main- taining a set speed or a set distance to the vehicle ahead. It is primarily intended for use on long straight roads in steady traffic, such as on highways and other main roads.

WARNING

• Do not use the adaptive cruise control system in demanding driving conditions such as city traffic, winding roads, at intersections, on slippery surfaces, in poor visibility, heavy rain, etc.

• Maintenance of cruise control compo-

nents must only be performed by an authorized Volvo workshop.

WARNING

• Adaptive cruise control cannot cover all

driving situations and traffic, weather and road conditions. The Function sec- tion provides information about limita- tions that the driver must be aware of before using the adaptive cruise con- trol.

• This system is designed to be a supple- mentary driving aid. It is not, however, intended to replace the driver's atten- tion and judgement. The driver is responsible for maintaining a safe dis- tance and speed and must intervene if adaptive cruise control does not main- tain a suitable speed or suitable dis- tance.

Adaptive Cruise Control (ACC)*

Function

04

Function overview

Warning light, braking by driver required

Controls

Radar sensor in front grille

Adaptive cruise control consists of: • A cruise control system to maintain a set

speed

• A system to maintain a set distance to the vehicle ahead (expressed as a time inter- val. For example, you can choose to remain approximately 2 seconds behind the vehicle ahead).

* Option/accessory, for more information, see Introduction.

167

``

04 Comfort and driving pleasure

Adaptive Cruise Control (ACC)*

WARNING

• Adaptive cruise control is not a collision avoidance system. The driver is always responsible for applying the brakes if the system does not detect another vehicle.

• Adaptive cruise control does not react to slow moving or stationary vehicles.

04

The distance to the vehicle ahead (in the same lane) is measured by a radar sensor. Your vehi- cle's speed is regulated by acceleration and braking. The brakes may emit a sound when they are being modulated by the adaptive cruise control system. This is normal.

WARNING

The brake pedal moves when the adaptive cruise control system modulates the brakes. Do not rest your foot under the brake pedal.

The adaptive cruise control system is designed to follow the vehicle ahead of you in the same lane, at a set time interval. If the radar sensor has not detected a vehicle ahead, the system will then attempt to maintain the set speed. This is also the case if the speed

of the vehicle ahead exceeds the speed that you have set. The adaptive cruise control system is designed to smoothly regulate speed. However, the driver must apply the brakes in situations that require immediate braking. This applies when there are great differences in speed between vehicles, or if the vehicle ahead brakes sud- denly.

WARNING

Due to limitations in the radar sensor, brak- ing may occur unexpectedly or not at all, see page 170.

Adaptive cruise control can only be activated at speeds above 20mph (30 km/h). If speed falls below 20 mph (30 km/h) or if engine speed (rpm) becomes too low, adaptive cruise control disengages and will no longer modulate the brakes. In situations when adaptive cruise con- trol cannot be activated Cruise Control Unavailable is shown in the display, see page 172.

WARNING

When adaptive cruise control disengages, the brakes will not be modulated automati- cally. The driver must assume full control over the vehicle.

Warning light-driver braking required Adaptive cruise control has a braking capacity that is equivalent to approximately 30% of the vehicle's total braking capacity. In situations requiring more brake force than ACC can pro- vide, if the driver does not apply the brakes, an audible signal will sound and a red warning light will illuminate in the windshield to alert the driver to react.

NOTE

Strong sunlight, reflections, extreme light contrasts, the use of sunglasses, or if the driver is not looking straight ahead may make the visual warning signal in the wind- shield difficult to see.

WARNING

Cruise control only warns of vehicles detected by the radar sensor, see page 170. In some cases there may be no warning or the warning may be delayed. The driver should always apply the brakes when necessary.

168

* Option/accessory, for more information, see Introduction.

04 Comfort and driving pleasure

Operation

Controls and display

Activate and resume settings, increase speed Standby mode, on/off

Set time interval

Activate and set a speed

Set speed (parentheses indicate standby mode) Time interval while it is being set

Time interval after it has been set

Engaging the cruise control function Before ACC can be used, it must first be put in standby mode. To do so, press . The symbol

illuminates in the display and (---) indicate

that ACC is in standby mode.

Setting a speed Use the buttons to store (set) the vehicle's current speed. The set speed, for example 55 mph, is shown in the display.

or

NOTE

Adaptive cruise control cannot be engaged at speeds below 20 mph (30 km/h).

The “car” symbol illuminates on the left side of the display when the radar sensor detects another vehicle ahead. The distance to a vehi- cle ahead is only regulated when this symbol is illumi-

nated.

Adjusting the set speed After a speed has been set, it can be increased or decreased by using the

buttons.

or

When the system is in active mode, the ton has the same function as a smaller increase in speed.

but- , but results in

Adaptive Cruise Control (ACC)*

NOTE

• If one of the adaptive cruise control but- tons is pressed for more than approxi- mately one minute, ACC will be deacti- vated. The engine must then be switched off and restarted to reset ACC. • In some situations cruise control cannot

be activated. Cruise Control Unavailable is shown in the display, see page 172.

Setting a time interval The set time interval to vehicles ahead is increased with . The current time interval is shown briefly in the dis- play following adjustment.

and decreased with

Five different time intervals can be selected and are shown in the display as 1–5
horizontal bars. The greater the number of bars, the longer the time interval. At low speeds, when the distance to the vehicle ahead is short, ACC increases the time interval slightly. In order to follow the vehi- cle ahead as smoothly as possible, ACC allows the time interval to vary considerably in certain situations.

04

``

* Option/accessory, for more information, see Introduction.

169

04 Comfort and driving pleasure

Adaptive Cruise Control (ACC)*

WARNING

• Only use a time interval that is suitable

in current traffic conditions.

• A short time interval gives the driver lim- ited reaction time if an unexpected sit- uation occurs in traffic.

04

The number of bars indicating the selected time interval are shown while the setting is being made and for several seconds afterward. A smaller version of the symbol is then shown to the right in the display. The same symbol is also displayed when Distance Alert is acti- vated, see page 174 .

Deactivating and resuming settings Cruise control is deactivated, either with a short press on driver, such as braking, etc. The set speed, for example 55 mph, is then shown in parenthe- ses. Speed and time interval are resumed by pressing

, or by action taken by the

WARNING

There may be a significant increase in speed after the

button has been pressed.

in standby mode or a long A short press on press in active mode deactivates cruise con-

trol. The set speed is then cleared and cannot be resumed. When ACC is activated, the vehicle’s speed increases by approximately 1 mph (1 km/h) each additional time

is pressed.

Deactivation due to action by the driver ACC is deactivated: • when the brakes are applied • if the gear selector is moved to N • if the accelerator pedal is depressed for an

extended period.

NOTE

If the accelerator pedal is only depressed for a short time, such as when passing another vehicle, ACC is deactivated temporarily and is reactivated when the pedal is released.