2014 Toyota Yaris Owners Manual

Vehicles with a power-adjustable type

To select a mirror to adjust, press the switch.

Left Right

To adjust the mirror, press the switch.

Up Right Down Left

64

1-3. Adjustable components (seats, mirrors, steering wheel)

Folding the mirrors

Push the mirror back in the direc- tion of the vehicle’s rear.

■Mirror angle can be adjusted when (vehicles with a power-adjustable

type) The engine switch is in the “ACC” or “ON” position.

■When the mirrors are fogged up (vehicles with an outside rear view

mirror defoggers) Turn on the mirror defoggers to defog the mirrors. (P. 199)

65

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When driving the vehicle

Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly

adjusted before driving.

■When a mirror is moving (vehicles with a power-adjustable type)

To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.

■When the mirror defoggers are operating (vehicles with an outside rear

view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

66

1

1-4. Opening and closing the windows Power windows

The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:

Window lock switch

Closing Opening One-touch opening (driver’s window only)*

*: To stop the window partway, operate the switch in the oppo- site direction.

Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.

■The power windows can be operated when

The engine switch is in the “ON” position.

■Operating the power windows after turning the engine off

The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened.

: If equipped 67

1-4. Opening and closing the windows

CAUTION

■Closing the windows

Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●Do not allow children to operate the power windows.

Closing a power window on someone can cause serious injury, and in some instances, even death.

68

1-5. Refueling Opening the fuel tank cap

Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle

Turn the engine switch off and ensure that all the doors and win- dows are closed.

■ Opening the fuel tank cap

Pull up the opener to open the fuel filler door.

Closing the fuel tank cap

Turn the fuel tank cap slowly to open.

After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.

69

1-5. Refueling

■Fuel types

Unleaded gasoline. (Octane rating 87 [Research Octane Number 91] or higher)

■Fuel tank capacity

Approximately 11.1 gal. (42 L, 9.2 Imp.gal.)

CAUTION

■When refueling the vehicle

Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.

●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.

●Do not allow anyone that has not discharged static electricity from their

body to come close to an open fuel tank.

●Do not inhale vaporized fuel.

Fuel contains substances that are harmful if inhaled.

●Do not smoke while refueling the vehicle.

Doing so may cause the fuel to ignite and cause a fire.

●Do not return to the vehicle or touch any person or object that is statically

charged. This may cause static electricity to build up, resulting in a possible ignition hazard.

70

1-5. Refueling

CAUTION

■When refueling

Securely insert the fuel nozzle into the fuel filler neck. If fuel is added with the nozzle slightly lifted away from the fuel filler neck, the automatic shut off function may not operate, resulting in fuel overflowing from the tank.

■When replacing the fuel cap

Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.

NOTICE

■Refueling

Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle’s painted surface.

71

1-6. Theft deterrent system Engine immobilizer system

The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.

The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed.

■System maintenance

The vehicle has a maintenance-free type engine immobilizer system.

■Conditions that may cause the system to malfunction

●If the grip portion of the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system

(key with a built-in transponder chip) of another vehicle

72

: If equipped

1

1-6. Theft deterrent system

■Certifications for the engine immobilizer system

U.S.A. FCC ID: MOZRI-33BTY FCC ID: PSIRI-37BTY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada This device complies with Industry Canada licence-exempt RSS stan- dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.

CAUTION

■Certifications for the immobilizer system

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE

■To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.

73

1-6. Theft deterrent system Alarm (Puerto Rico)

The system sounds the alarm and flashes the lights when forced entry is detected. ■ Triggering of the alarm

The alarm is triggered in the following situations when the alarm is set: ● A locked door is unlocked or opened in any way other than using a key or wireless remote control. (The doors will lock again automatically.) ● The hood is opened. ● The battery is reconnected.

■ Setting the alarm system

Close the doors and hood, and lock all the doors. The system will be set automati- cally after 30 seconds.

indicator

The light changes from being on to flashing when the system is set.

■ Deactivating or stopping the alarm

Do one of the following to deactivate or stop the alarm: ● Unlock the doors. ● Turn the engine switch to the “ACC” or “ON” position, or start the engine. (The alarm will be deactivated or stopped after a few seconds.)

74

1

1-6. Theft deterrent system

■System maintenance

The vehicle has a maintenance-free type alarm system.

■Items to check before locking the vehicle

To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ●Nobody is in the vehicle. ●The windows are closed before the alarm is set. ●No valuables or other personal items are left in the vehicle.

■Triggering of the alarm

The alarm may be triggered in the following situations: (Stopping the alarm deactivates the alarm system.)

●A person inside the vehicle opens a

door or hood.

●The battery is recharged or replaced

when the vehicle is locked.

■When the battery is disconnected Be sure to cancel the alarm system. If the battery is disconnected before canceling the alarm, the system may be triggered when the battery is reconnected.

75

1-6. Theft deterrent system

■Alarm-operated door lock

●When the alarm is operating, the doors are locked automatically to pre-

vent intruders.

●Do not leave the key inside the vehicle when the alarm is operating, and make sure the key is not inside the vehicle when recharging or replacing the battery.

NOTICE

■To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.

76

1-6. Theft deterrent system Theft prevention labels (except Canada)

These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.

77

1-7. Safety information Correct driving posture

Drive with a good posture as follows:

and to

Sit upright and well back in the seat. (P. 43) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (P. 43) Adjust the seatback so that the controls are easily oper- able. (P. 43) Adjust the tilt positions of the steering wheel down- ward so the airbag is facing your chest. (P. 62) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (P. 51) Wear the seat belt correctly. (P. 54)

78

1-7. Safety information

CAUTION

■While driving

●Do not adjust the position of the driver’s seat.

Doing so could cause the driver to lose control of the vehicle.

●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.

●Do not place anything under the front seats.

Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent, resulting in death or serious injury. The adjustment mechanism may also be damaged.

■Adjusting the seat position

●Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

●Do not put your hands under the seat or near the moving parts to avoid

injury. Fingers or hands may become jammed in the seat mechanism.

79

1-7. Safety information SRS airbags

The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.

SRS front airbags

SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components. SRS driver knee airbag Can help provide driver protection. SRS seat cushion airbags Can help restrain the driver and front passenger.

80

1-7. Safety information

SRS side and curtain shield airbags

SRS side airbags Can help protect the torso of the front seat occupants. SRS curtain shield airbags Can help protect primarily the head of occupants in the outer seats.

81

1-7. Safety information

SRS airbag system components

Curtain shield airbags Side impact sensors (front) Side airbags Side impact sensors (rear) SRS warning light Driver airbag Passenger seat cushion airbag Front passenger’s seat belt buckle switch Seat belt pretensioners and force limiters Side impact sensors (front door)

Driver seat cushion airbag Driver’s seat belt buckle switch Driver knee airbag Front impact sensors Airbag sensor assembly Front passenger occupant classification system (ECU and sensors) Front passenger airbag “AIR BAG ON” and “AIR BAG OFF” indicator lights

82

1

1-7. Safety information

Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants.

■If the SRS airbags deploy (inflate)

●Bruising and slight abrasions may result from contact with a deploying

(inflating) SRS airbag.

●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes. The airbag itself may also be hot.

●The windshield may crack.

■SRS airbag deployment conditions (SRS front airbags)

●The SRS front airbags and SRS seat cushion airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approximately 12 - 18 mph [20 - 30 km/h] frontal col- lision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle and sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck etc.).

●Depending on the type of collision, it is possible that only the seat belt

pretensioners will activate.

●The SRS front airbags and seat cushion airbag for the front passenger will not activate if there is no passenger sitting in the front passenger seat. However, the SRS front airbags and seat cushion airbag for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied.

●The SRS seat cushion airbags on the front seats will not operate if the

occupant is not wearing a seat belt.

83

1-7. Safety information

■SRS airbag deployment conditions (SRS side and curtain shield air-

bags) The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by an approximately 3300 lb. [1500 kg] vehicle collid- ing with the vehicle cabin from a direction perpendicular to the vehicle orien- tation at an approximate speed of 12 - 18 mph [20 - 30 km/h]).

■Conditions under which the SRS airbags may deploy (inflate), other

than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

●Hitting a curb, edge of pavement or

hard surface

●Falling into or jumping over a deep hole ●Landing hard or falling

■Types of collisions that may not deploy the SRS airbags (SRS front air-

bags) The SRS front airbags and SRS seat cushion airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, deployment of the SRS front airbags may occur.

●Collision from the side ●Collision from the rear ●Vehicle rollover

84

1-7. Safety information

■Types of collisions that may not deploy the SRS airbags

(SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.

●Collision from the side to the vehicle body other than the passenger com- partment

●Collision from the side at an angle

The SRS side and curtain shield airbags do not generally inflate if the vehi- cle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low-speed side collision.

●Collision from the front ●Collision from the rear ●Vehicle rollover

■When to contact your Toyota dealer

In the following cases, contact your Toyota dealer as soon as possible. ●Any of the SRS airbags have been inflated.

●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS front airbags and SRS seat cushion airbags to inflate.

85

1-7. Safety information

●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side and cur- tain shield airbags to inflate.

●The pad section of the steering wheel, dashboard near the front passenger air- bag or lower portion of the instrument panel is scratched, cracked, or other- wise damaged.

●The

front seat cushion surface

is scratched, cracked, or otherwise dam- aged.

●The surface of the seats with the side airbag is scratched, cracked or other- wise damaged.

●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags is inside scratched, cracked, or otherwise damaged.

86

1

1-7. Safety information

CAUTION

■SRS airbag precautions

Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts

properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (NHTSA) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching the

pedals comfortably.

• Slightly recline the back of the seat. Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, simply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature.

• If your steering wheel is adjustable, tilt it downward. This points the air-

bag toward your chest instead of your head and neck.

The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.

87

1-7. Safety information

CAUTION

■SRS airbag precautions

●If the seat belt extender has been con- nected to the front seat belt buckles but the seat belt extender has not also been fastened to the latch plate of the seat belt, the SRS front airbags will judge that the driver and front passen- ger are wearing the seat belt even though the seat belt has not been con- nected. In this case, the SRS front air- bags may not activate correctly in a collision, resulting in death or serious injury in the event of a collision. Be sure to wear the seat belt with the seat belt extender.

●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.

●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat. (P. 98)

●Do not sit on the edge of the seat or

lean against the dashboard.

88

1

CAUTION

■SRS airbag precautions

1-7. Safety information

●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.

●Do not allow the front seat occupants to

hold items on their knees.

●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.

●Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.

●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and driver knee airbags deploy.

89

1-7. Safety information

CAUTION

■SRS airbag precautions

●Do not attach anything to areas such as a door, windshield glass, side door glass, front or rear pillar, roof side rail and assist grip.

●Do not attach any heavy, sharp or hard objects such as keys and accessories to the key. The objects may restrict the SRS driver knee airbag inflation or be thrust into the driver’s seat area by the force of the deploying airbag, thus causing a danger.

●Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy.

●If a vinyl cover is put on the area where the SRS driver knee airbag will

deploy, be sure to remove it.

●Do not use seat accessories which cover the parts where the SRS side airbags and SRS seat cushion airbags inflate as they may interfere with inflation of the SRS airbags. Such accessories may prevent the side air- bags and seat cushion airbags from activating correctly, disable the sys- tem or cause the side airbags and seat cushion airbags to inflate accidentally, resulting in death or serious injury.

●Do not strike or apply significant levels of force to the area of the SRS air-

bag components. Doing so can cause the SRS airbags to malfunction.

●Do not touch any of the component parts immediately after the SRS air-

bags have deployed (inflated) as they may be hot.

90

1-7. Safety information

CAUTION

■SRS airbag precautions

●If breathing becomes difficult after the SRS airbags have deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.

●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.

●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the SRS front airbags for the front passenger may not deploy in the event of a collision.

■Modification and disposal of SRS airbag system components

Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags. ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails.

●Repairs or modifications of the front fender, front bumper, or side of the

occupant compartment.

●Installation of snow plows, winches, etc. to the front grille (bull bars or kan-

garoo bar etc.).

●Modifications to the vehicle’s suspension system. ●Installation of electronic devices such as mobile two-way radios and CD

players.

●Modifications to your vehicle for a person with a physical disability.

91

1-7. Safety information Front passenger occupant classification system

Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger.

SRS warning light Seat belt reminder light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light

92

1-7. Safety information

Condition and operation in the front passenger occupant classification system ■ Adult*1

Indicator/ warning light

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Seat belt reminder light

Front passenger airbag

Side airbag on the front passenger seat

Curtain shield airbag in the front passenger

side

Seat cushion airbag in the front passenger

side

Devices

“AIR BAG

ON” Off Off*2
or

flashing*3

Activated

Activated*2

or

deactivated*3

■ Child*4

Indicator/ warning light

Front passenger’s seat belt pretensioner

Activated

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

“AIR BAG OFF” or “AIR BAG ON”*4

SRS warning light

Seat belt reminder light

Front passenger airbag

Off

Off*2 or flashing*3
Deactivated activated*4

or

Devices

Side airbag on the front passenger seat

Curtain shield airbag in the front passenger

side

Seat cushion airbag in the front passenger

side

Front passenger’s seat belt pretensioner

Activated

or

Deactivated activated*2,4
Activated

93

1-7. Safety information

■ Child restraint system with infant*5

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

“AIR BAG OFF”*6

Indicator/ warning light

SRS warning light

Seat belt reminder light

Devices

Front passenger airbag

Side airbag on the front passenger seat

Curtain shield airbag in the front passenger

side

Seat cushion airbag in the front passenger

side

Off Off*2
or

flashing*3
Deactivated

Activated

Deactivated

Front passenger’s seat belt pretensioner

Activated

■ Unoccupied

Indicator/ warning light

Devices

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

SRS warning light

Seat belt reminder light Front passenger airbag

Side airbag on the front passenger seat

Curtain shield airbag in the front passenger

side

Seat cushion airbag in the front passenger

side

“AIR BAG

OFF”

Off

Deactivated

Activated

Deactivated

Front passenger’s seat belt pretensioner

Activated

94

On

Deactivated

Activated

Deactivated

1-7. Safety information

■ There is a malfunction in the system

“AIR BAG ON” and “AIR BAG OFF”

indicator lights

“AIR BAG

OFF”

Indicator/ warning light

SRS warning light

Seat belt reminder light Front passenger airbag

Devices

Side airbag on the front passenger seat

Curtain shield airbag in the front passenger

side

Seat cushion airbag in the front passenger

side

Front passenger’s seat belt pretensioner

Activated

*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may not recognize him/her as an adult depending on his/her physique and posture.

*2: In the event the front passenger is wearing a seat belt. *3: In the event the front passenger does not wear a seat belt. *4: For some children, child in seat, child in booster seat or child in convertible seat, the system may not recognize him/her as a child. Factors which may affect this can be the physique or posture.

*5: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (P. 98)

*6: In case the indicator light is not illuminated, consult this manual on

how to install the child restraint system properly. (P. 102)

95

1-7. Safety information

CAUTION

■Front passenger occupant classification system precautions

Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger’s seat belt plate has not been left inserted

into the buckle before someone sits in the front passenger seat.

●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, and reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the SRS airbags for the passenger may not activate correctly, which could cause death or serious injury in the event of collision.

●Do not apply a heavy load to the front passenger seat or equipment (e.g.

seatback pocket).

●Do not put weight on the front passenger seat by putting your hands or

feet on the front passenger seat seatback from the rear passenger seat.

●Do not let a rear passenger lift the front passenger seat with their feet or

press on the seatback with their legs.

●Do not put objects under the front passenger seat.

96

1

1-7. Safety information

CAUTION

■Front passenger occupant classification system precautions

●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.

●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.

●When it is unavoidable to install a forward-facing child restraint system on the front passenger seat, install the child restraint system on the front pas- senger seat in the proper order. (P. 102)

●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.

●Child restraint systems installed on the rear seat should not contact the

front seatbacks.

●Do not use a seat accessory, such as a cushion and seat cover, that cov-

ers the seat cushion surface.

●Do not modify or replace the upholstery of the front seat.

97

1-7. Safety information Child restraint systems

A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.

Points to remember

Studies have shown that installing a child restraint on a rear seat is much safer than installing one on the front passenger seat. ● Choose a child restraint system that suits your vehicle and is

appropriate to the age and size of the child.

● For installation details, follow the instructions provided with the

child restraint system. General installation instructions are provided in this manual. (P. 102)

Types of child restraints

Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing — Infant seat/convertible seat

98

Forward facing — Convertible seat

1-7. Safety information

Booster seat

■Selecting an appropriate child restraint system

●Use a child restraint system appropriate for the child until the child

becomes large enough to properly wear the vehicle’s seat belts.

●If a child is too large for a child restraint system, sit the child on a rear

seat and use the vehicle’s seat belt. (P. 54)

99

1-7. Safety information

CAUTION

■Child restraint precautions

●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.

●Never install a rear-facing child restraint system on the front passenger seat even if the “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.

●A forward-facing child restraint system may be installed on the front pas- senger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illumi- nated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.

●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of sudden braking, sudden swerving or an accident.

●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rails from which the SRS side airbags or SRS curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the SRS side airbags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.

100

1

1-7. Safety information

CAUTION

■Child restraint precautions

●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop or an accident.

■When children are in the vehicle

Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

■When the child restraint system is not in use

●Keep the child restraint system properly secured on the seat even if it is not in use. Do not store the child restraint system unsecured in the pas- senger compartment.

●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the luggage compartment. This will prevent it from injuring passengers in the event of sudden braking, sudden swerving or an accident.

101

1-7. Safety information Installing child restraints

Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.

Child restraint LATCH anchors LATCH anchors are provided for the outside rear seats. (But- tons displaying the location of the anchors are attached to the seats.)

Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (P. 54)

Anchor brackets (for top tether strap)

An anchor bracket is provided for each rear seat.

102

1-7. Safety information

Installation with LATCH system

Type A

Widen the gap between the seat cushion and seatback slightly.

Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

Canada only

103

1-7. Safety information

Type B

Widen the gap between the seat cushion and seatback slightly.

If

the buckles onto

the Latch LATCH anchors. the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

Canada only

Installing child restraints using a seat belt (child restraint lock function belt)

■ Rear facing Infant seat/convertible seat

Place the child restraint system on the rear seat facing the rear of the vehicle.

104

1-7. Safety information

Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

While pushing the child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

the shoulder belt has After retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

105

1-7. Safety information

■ Forward facing Convertible seat

Remove the head restraint. (P. 51)

Place the child restraint system on the seat facing the front of the vehicle.

Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

106

1-7. Safety information

While pushing the child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (P. 108)

■ Booster seat

Place the child restraint system on the seat facing the front of the vehicle.

Sit the child in the child restraint system. Fit the seat belt to the child restraint system according to the manufacturer’s instruc- tions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child’s shoulder and that the lap belt is as low as possible. (P. 54)

107

1-7. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Child restraint systems with a top tether strap

Remove the luggage cover. (P. 218) Remove the head restraint. (P. 51) Secure the child restraint system using the LATCH anchors or a seat belt.

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched.

Reinstall the luggage cover.

■Laws and regulations pertaining to anchorages

The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

108

1-7. Safety information

CAUTION

■When installing a booster seat

To prevent the belt from going into ALR lock mode, do not fully extend the shoulder belt. ALR mode causes the belt to tighten only. This could cause injury or discomfort to the child. (P. 57)

■When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.

●If the driver’s seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

●Adjust the front passenger seat so that it does not interfere with the child restraint system.

●Only put a forward-facing child restraint system on the front seat when unavoid- able. When installing a forward-facing child restraint system on the front pas- senger seat, move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated. Failure to do so may result in death or serious injury if the airbags deploy (inflate).

●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder. Failure to do so may result in death or serious injury in the event of sudden braking, sudden swerving or an accident.

●Ensure that the belt and plate are securely locked and the seat belt is not

twisted.

109

1-7. Safety information

CAUTION

■When installing a child restraint system

●Push and pull the child restraint system from side to side and forward to be

sure it is secure.

●After securing a child restraint system, never adjust the seat. ●Follow all installation instructions provided by the child restraint system

manufacturer.

●When a child restraint system with a top tether strap is installed, do not install the head restraint. The head restraint may interfere with the top tether strap preventing secure installation of the child restraint system.

●Make sure to properly store the removed head restraint in a secure place

when you use the child restraint system on the rear seat.

●When using the right side seat for the child restraint system, do not sit in the center seat. Seat belt function may be impaired, such as being positioned overly high or loose-fitting, which may result in death or serious injury in the event of sudden braking or an accident.

■Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sud- den braking, sudden swerving or an accident.

■To correctly attach a child restraint system to the anchors

When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of sudden braking, sudden swerving or an accident.

110

When driving

2-4. Using other driving systems Cruise control................... 159
Driving assist systems ..... 163

2-5. Driving information

Cargo and luggage .......... 168
Vehicle load limits ............ 172
Winter driving tips ............ 173
Trailer towing (except 3-door models for Canada).................... 177
Trailer towing (3-door models for Canada) ....... 178
Dinghy towing (vehicles with an automatic transmission) ................. 188
Dinghy towing (vehicles with a manual transmission) ................. 189

2-1. Driving procedures

Driving the vehicle............ 112
Engine (ignition) switch.... 124
Automatic transmission.... 127
Manual transmission........ 129
Turn signal lever .............. 130
Parking brake................... 131
Horn ................................. 132

2-2.

Instrument cluster Gauges and meters ......... 133
Indicators and warning lights .............................. 136
Multi-information display............................ 140

2-3. Operating the lights and

wipers Headlight switch............... 145
Fog light switch ................ 149
Windshield wiper and washer ........................... 151
Rear window wiper and washer ........................... 154

111

2-1. Driving procedures Driving the vehicle

The following procedures should be observed to ensure safe driv- ing: ■ Starting the engine

 P. 124
■ Driving Vehicles with an automatic transmission

With the brake pedal depressed, shift the shift lever to D. (P. 127) Release the parking brake. (P. 131) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.

Vehicles with a manual transmission

While depressing the clutch pedal, shift the shift lever to 1. (P. 129) Release the parking brake. (P. 131) Gradually release the clutch pedal. At the same time, gently depress the accelerator pedal to accelerate the vehicle.

■ Stopping Vehicles with an automatic transmission

With the shift lever in D, depress the brake pedal. If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to P or N. (P. 127) Vehicles with a manual transmission

While depressing the clutch pedal, depress the brake pedal. If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to N. (P. 129)

112

2

2-1. Driving procedures

■ Parking the vehicle Vehicles with an automatic transmission

With the shift lever in D, depress the brake pedal. Set the parking brake. (P. 131) Shift the shift lever to P. (P. 127) If parking on a hill, block the wheels as needed. Turn the engine switch to the “LOCK” position to stop the engine. Lock the door, making sure that you have the key on your person.

Vehicles with a manual transmission

While depressing the clutch pedal, depress the brake pedal. Set the parking brake. (P. 131) Shift the shift lever to N. (P. 129) If parking on a hill, shift the shift lever to 1 or R and block the wheels as needed. Turn the engine switch to the “LOCK” position to stop the engine. Lock the door, making sure that you have the key on your person.

Starting off on a steep uphill

Vehicles with an automatic transmission

Make sure that the parking brake is set and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

113

2-1. Driving procedures

Vehicles with a manual transmission

With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1. Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be

especially slippery.

●Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Engine speed while driving

In the following conditions, the engine speed may become high while driving. This is due to automatic up-shifting control or down-shifting implementation to meet driving conditions. It does not indicate sudden acceleration. ●The vehicle is judged to be driving uphill or downhill ●When the accelerator pedal is released

■Breaking in your new Toyota

To extend the life of the vehicle, observing the following precautions is rec- ommended: ●For the first 200 miles (300 km):

Avoid sudden stops.

●For the first 500 miles (800 km) (3-door models for Canada):

Do not tow a trailer.

●For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in low gears. • Do not drive at a constant speed for extended periods.

114

2

2-1. Driving procedures

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (P. 346)

■Eco-friendly driving (vehicles with an automatic transmission)

Vehicles without a tachometer

Vehicles with a tachometer

During Eco-friendly acceleration opera- tion (Eco driving), Eco Driving Indicator Light will turn on. When the accelerator pedal is depressed excessively, and when the vehicle is stopped, the light turns off. Eco Driving Indicator Light will not oper- ate in the following conditions: ●The shift lever is in anything other than

D.

●The vehicle speed is approximately

80 mph (130 km/h) or higher.

Eco Driving Indicator Light can be acti- vated or deactivated. (P. 143)

115

2-1. Driving procedures

CAUTION

■When starting the vehicle (vehicles with an automatic transmission)

Always keep your foot on the brake pedal while stopped with the engine run- ning. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly. This allows you to depress the brake and acceler- ator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. These hot parts may cause a fire if there is any flammable material nearby.

●On vehicles with an automatic transmission, do not let the vehicle roll backward while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.

●If the smell of exhaust is noticed inside the vehicle, open the windows and check that the back door is closed. Large amounts of exhaust in the vehi- cle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately.

●On vehicles with an automatic transmission, do not shift the shift lever to P

while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control.

116

2