2010 Toyota Yaris Sedan Owners Manual

151

2-5. Driving information Trailer towing (Canada)

Your vehicle is designed primarily as a passenger-carrying vehicle, thus towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. n Weight limits

Confirm the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

n Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum of weights of the unloaded vehi- cle, driver, passengers, luggage, hitch, and the trailer tongue load. It also includes the weight of any special equipment installed on your vehicle.

n Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

152

2-5. Driving information

n Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum 70 lb. (32 kg) (Tongue load / Total trailer weight × 100
= 9 to 11%) The total trailer weight and tongue load can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

Total trailer weight Tongue load

153

2-5. Driving information

Towing a trailer

Consult your Toyota dealer for further information about additional requirements such as a towing kits, etc.

n Before towing

Check that the following conditions are met: l Ensure that your vehicle’s tires are properly inflated. (→P. 341) l Trailer tires should be inflated according to the trailer manufacturer’s rec-

ommendation.

l All trailer lights work to be legal. l Confirm all lights work each time you connect them. l Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

l Make sure the trailer cargo is securely loaded. l Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. n Break-in schedule

l Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bearings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

n Maintenance

If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

l Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km).

154

2

2-5. Driving information

CAUTION

n To avoid accident or injury

l The total trailer weight (trailer weight plus the weight of cargo) must not

exceed 700 lb. (318 kg)

l Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

n Hitches

If you wish to install a trailer hitch, your Toyota dealer should be consulted.

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maximum weight rating specified for the trailer hitch. l Use only a hitch that conforms to the total trailer weight requirement. l Follow the directions supplied by the hitch manufacturer. l Lubricate the hitch ball with a light coat of grease. l Remove the trailer hitch whenever you are not towing a trailer to reduce the possibility of additional damage caused by the hitch if your vehicle is struck from behind.

n When towing a trailer

l Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

l Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

155

2-5. Driving information

NOTICE

n When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

n Brakes

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations.

n Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

n Do not directly splice trailer lights

Directly splicing may damage your vehicle’s electrical system and cause a malfunction.

Trailer towing tips

Your vehicle will handle differently when towing a trailer. In order to avoid accident, death or serious injury, keep the following in mind when towing: l Before starting out, check the trailer’s light and the vehicle-trailer

connections. Recheck after driving a short distance.

l Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

156

2-5. Driving information

l Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

l As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

l Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

l Avoid jerky starts or sudden acceleration. Vehicles with a manual transmission, prevent excessive clutch slippage by keeping engine rpm low and not racing the engine. Always start out in first gear.

l Avoid jerky steering and sharp turns, and slow down before mak-

ing a turn.

l Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

l Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

l Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

157

2-5. Driving information

In order to maintain engine braking efficiency, do not use the trans- mission in D (automatic transmission) or 5 (manual transmission). l Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 325)

l Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoidable, do so only after performing the following:

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into 1 or R (manual transmission) or P (automatic trans- mission) and turn off the engine.

l When restarting after parking on a slope:

With the transmission in P (automatic transmission) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake (also brake pedal on vehicles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

158

2-5. Driving information

CAUTION

n To avoid an accident

l Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

l Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

l Avoid holding the brake pedal down too long or too frequently. This could

cause the brakes to overheat and result in reduced braking efficiency.

159

2-5. Driving information Dinghy towing (vehicles with an automatic transmission)

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

n To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

160

2-5. Driving information Dinghy towing (vehicles with a manual transmission)

Your vehicle can be dinghy towed in a forward direction (with 4
wheels on the ground) behind a motor home.

Dinghy towing does not elimi- nate the possibility of damage to your vehicle.

Towing your vehicle with 4 wheels on the ground

To prevent damage to your vehicle, perform the following procedures before towing.

Shift the shift lever to N. Turn the engine switch to the ACC position. Ensure that the audio system and other powered devices have been turned off. Release the parking brake. After towing, leave the engine in idle for at least 3 minutes before driving the vehicle.

n Necessary equipment and accessories

Specialized equipment and accessories are required for dinghy towing. Con- tact the service branch of the motor home manufacturer regarding recom- mended equipment.

161

2-5. Driving information

NOTICE

n Dinghy towing direction

Do not tow the vehicle backwards. Doing so may cause serious damage.

n To prevent the steering from locking

Ensure the engine switch is in the ACC position.

162

3-1. Using the air conditioning system and defogger Air conditioning system

Air conditioning ON/OFF switch

Fan speed control dial

Air intake selection dial

Air outlet selection dial

Temperature control dial

Adjusting the settings

n Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

is not pressed, the system will blow ambient temperature air or

If heated air. For quick cooling, turn the temperature control dial to the “MAX A/C”

position and set the air intake selection dial to mode.

(recirculated air)

164

3-1. Using the air conditioning system and defogger

n Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Set the dial to “0” to turn the fan off.

n Selecting the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment.

When the dial is set to flows to the upper body.

, air

When the dial is set to , air flows to the upper body and feet.

: Some models

165

3-1. Using the air conditioning system and defogger

: Some models

: Some models

When the dial is set to mainly air flows to the feet.

When the dial is set to , air flows to the feet and the wind- shield defogger operates.

When the dial is set to , air flows to the windshield and side windows to defog them.

Set the air intake selection dial to

(outside air) mode.

Pressing to turn the air conditioning on clears the wind- shield and side windows faster.

n Selecting the air intake modes

Set the air intake selection dial to

(outside air) mode or

(recirculated air) mode.

166

3-1. Using the air conditioning system and defogger

Adjusting the position of the air outlets

Center outlets

Direct air flow to the left or right, up or down.

167

3-1. Using the air conditioning system and defogger

Right and left side outlets

Direct air flow to the left or right, up or down.

Opening and closing the right and left side outlets

Open the vent. Close the vent.

168

3-1. Using the air conditioning system and defogger

n Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n When outside air temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

is pressed.

n When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature adjust- ment dial.

n Air conditioning odors

l During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

l To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

CAUTION

n To prevent the windshield from fogging up

Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

n To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

169

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers∗

These features are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors.

On/off

Press the button to turn on the rear window defogger. The indicator light will come on. Pressing the button again also turns the defoggers off. Vehicles with timer: The defog- gers will automatically turn off after approximately 15 min- utes.

n The rear window and outside rear view mirror defoggers can be oper-

ated when The engine switch is in the ON position.

n Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

n When the outside rear view mirror defoggers are on (vehicles with out-

side rear view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

170

∗: If equipped

3-1. Using the air conditioning system and defogger

NOTICE

n To prevent battery discharge

Do not leave the rear window defogger on longer than necessary when the engine is stopped.

171

3-2. Using the audio system Audio system types

CD player with external CD changer controller and AM/FM radio.

Type A

Type B

172

3-2. Using the audio system

Title

Using the radio Using the CD player Playing back MP3 and WMA discs Optimal use of the audio system Using the AUX adapter

Page P. 175
P. 181
P. 187
P. 194
P. 196

n Using cellular phones

Interference may be heard through the audio system’s speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

CAUTION

n For vehicles sold in U.S.A. and Canada

l Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

l Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

l CAUTION

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

173

3-2. Using the audio system

NOTICE

n To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine off.

n To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

174

3-2. Using the audio system Using the radio

Type A

Power

Volume

Station selector

Frequency adjust (AM, FM mode) or channel (SAT mode)

Station scan

AM·SAT/FM mode but-

Frequency seek

Type B

Power

Volume

Text message display (SAT mode)

Station selector

Frequency adjust (AM, FM mode) or channel (SAT mode)

Station scan

Frequency seek

AM·SAT/FM mode buttons

Text message display (SAT mode)

175

3-2. Using the audio system

Setting station presets (excluding XM® Satellite Radio)

Search for desired stations by turning

or

or

pressing “∧” or “∨” on

or

Press and hold the button (from

or ) that the station is to be set to until you hear a beep.

or

to

Scanning radio stations (excluding XM® Satellite Radio) n Scanning the preset radio stations

Press and hold

or

until you hear a beep.

Preset stations will be played for 5 seconds each. When the desired station is reached, press the button once again.

n Scanning all radio stations within range

Press

or

All stations with reception will be played for 5 seconds each. When the desired station is reached, press the button once again.

XM® Satellite Radio* (if equipped) n Receiving XM® Satellite Radio

Press

or

and select the XM® band.

The display changes as follows each time is pressed. AM → SAT1 → SAT2 → SAT3

or

176

3-2. Using the audio system

Turn

or

to select the desired channel in the all

categories or press “∧” or “∨” on or select the desired channel in the current category.

to

n Setting XM® Satellite Radio channel presets

Select the desired channel. Press and hold the button (from or you hear a beep.

) that the channel is to be set to until

or

to

n Changing the channel category

Press “∧” or “∨” on the

or

n Scanning XM® Satellite Radio channels

l Scanning channels in the current category

Press When the desired channel is reached, press

or

again.

l Scanning preset channels

Press and hold When the desired channel is reached, press

until you hear a beep.

or

again.

n Displaying text information

or

Press The display will show up to 10 characters. The display changes as follows each time the button is pressed. l CH NAME l TITLE (SONG/PROGRAM TITLE) l NAME (ARTIST NAME/FEATURE) l CH NUMBER

or

or

177

3-2. Using the audio system

*:Use of XM® Satellite Radio requires XM® tuner and service.

Contact your Toyota dealer.

n When the battery is disconnected

Stations presets are erased.

n Reception sensitivity

l Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.

l The radio antenna is mounted inside the rear window. To maintain clear radio reception, do not attach metallic window tinting or other metallic objects to the antenna wire mounted inside the rear window.

n XM® Satellite Radio

An XM® Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con- tiguous states and 10 Canadian provinces. l XM® subscriptions

For detailed information about XM® Satellite Radio or to subscribe: U.S.A.— Visit on the web at www.xmradio.com or call 1-800-967-2346. Canada— Visit on the web at www.xmradio.ca or call 1-877-438-9677.

l Radio ID

You will need the radio ID when activating XM® service or reporting a

problem. Select “CH000” using character ID number will appear.

or

, and the receiver’s 8-

l Satellite tuner

The tuner supports only Audio Services (Music and Talk) and the accom- panying Text Information of XM® Satellite Radio.

178

3-2. Using the audio system

n If the satellite radio does not operate normally

If a problem occurs with the XM® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggested corrective action.

ANTENNA

UPDATING

NO SIGNAL

LOADING

OFF AIR

-----

The XM® antenna is not connected. Check whether the XM® antenna cable is attached securely. There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. You have not subscribed to the XM® Satellite Radio. The radio is being updated with the latest encryption code. Contact the XM® Satellite Radio for subscription information. When a contract is canceled, you can choose the “CH000” and all free-to-air channels. The premium channel you selected is not autho- rized. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. If you want to listen to the premium chan- nel, contact the XM® Satellite Radio. The XM® signal is too weak at the current location. Wait until your vehicle reaches a location with a stronger signal. The unit is acquiring audio or program information. Wait until the unit has received the information. The channel you selected is not broadcasting any programming. Select another channel. There is no song/program title or artist name/fea- ture associated with the channel at that time. No action needed.

179

3-2. Using the audio system

---

The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel.

Contact the XM® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877-438-9677 (Canada).

n Certifications for the radio tuner

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by trying one or more of the following: l Reorienting or relocate the receiving antenna. l Connecting the equipment into an outlet on a circuit different from that to

Increasing the separation between the equipment and receiver.

which the receiver is connected.

l Consulting the dealer or an experienced radio/TV technician for help.

180

3-2. Using the audio system Using the CD player

Type A

Power

Volume

CD selection (with external CD changer only)

CD eject

Repeat play

Playback

Random playback

Text message display

Track selection

Type B

Reverse

Fast-forward

Search playback

Power

Volume

CD selection (with external CD changer only)

CD eject

Reverse

Fast-forward

Search playback

Repeat play

Track selection

Random playback

Text message display

Playback

181

3-2. Using the audio system

Loading a CD

Insert a CD.

Ejecting a CD

Press

or

and remove the CD.

Selecting and scanning a track

n Selecting a track

Press “∧” to move up or “∨” to move down using

or

until the desired track number is displayed.

n Scanning tracks

or

Press The first 10 seconds of each track will be played. Press the switch again when the desired track is reached.

Fast-forwarding and reversing tracks

To fast-forward or reverse. Type A: Press and hold Type B: Press and hold

) or ) or

). ).

Selecting a CD (with external CD changer only)

n Selecting the desired CD (∨) or (∨) or

Type A: Press Type B: Press

n Scanning loaded CDs Press and hold

182

(∧). (∧).

or

until you hear a beep.

3-2. Using the audio system

The first 10 seconds of the first track on each CD will be played. Press the switch again when the desired CD is reached.

Repeat play

n Repeating a track

Press

(RPT) or

(RPT).

n Repeating all of the tracks on a CD (with external CD changer

only) Press and hold

Random playback

n Current CD

(RPT) or

(RPT) until you hear a beep.

(RAND) or

Press Tracks are played in a random order until the button is pressed once more.

(RAND).

n All CDs (with external CD changer only)

(RAND) or

Press and hold beep. Tracks on all loaded CDs are played in a random order until the button is pressed once more.

(RAND) until you hear a

Switching the display

Press

or

Each time the switch is pressed, the display changes in the order of Track no./Elapsed time→CD title→Track name.

183

3-2. Using the audio system

n Display

Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters. A maximum of 24 characters can be displayed. If is pressed for 1 second or more again or has not been pressed for 6 seconds or more, the display will return to the first 12 charac- ters. Depending on the contents recorded, the characters may not be displayed properly or may not be displayed at all.

or

or

n Canceling random playback

Press

(RAND) or

(RAND) again.

n Canceling repeat play (RPT) or

Press

n Error messages

(RPT) again.

“ERROR”: This indicates a trouble either in the CD or inside the player.

The CD may be dirty, damaged or inserted up-side down.

n Discs that can be used

Discs with the marks shown below can be used. Playback may not be possible depending on recording format or disc fea- tures, or due to scratches, dirt or deterioration.

CDs with copy-protect features may not be used.

n CD player protection feature

To protect the internal components, playback is automatically stopped when a problem is detected while the CD player is being used.

n If CDs are left inside the CD player or in the ejected position for

extended periods CDs may be damaged and may not play properly.

n Lens cleaners

Do not use lens cleaners. Doing so may damage the CD player.

184

3-2. Using the audio system

NOTICE

n CDs and adapters that cannot be used

Do not use the following types of CDs or 3 in. (8 cm) CD adapters or Dual Disc. Doing so may damage the CD player and/or the CD insert/eject function.

l CDs that have a diameter that is not 4.7

in. (12 cm)

l Low-quality and deformed CDs

l CDs with a transparent or translucent

recording area

l CDs that have had tape, stickers or CD- R labels attached to them, or that have had the label peeled off

185

3-2. Using the audio system

NOTICE

n CD player precautions

Failure to follow the precautions below may result in serious damage to the CDs or the player itself. l Do not insert anything other than CDs into the CD slot. l Do not apply oil to the CD player. l Store CDs away from direct sunlight. l Never try to disassemble any part of the CD player.

186

3-2. Using the audio system Playing back MP3 and WMA discs

Type A

Power

Volume

File selection

Folder selection

Playback

Disc eject

Repeat play

File selection

Reverse

Fast-forward

Search playback

Random playback

Text message display

Type B

Power

Volume

Disc eject

Fast-forward Reverse

File selection

Folder selection

File selection

Search playback

Repeat play

Text message display

Random playback

Playback

187

3-2. Using the audio system

Loading MP3 and WMA disc

Insert a disc.

Ejecting MP3 and WMA disc

Press

or

and remove the disc.

Selecting a folder

n Selecting folders one at a time

To select the desired folder, press “∧” or “∨” on

or

n Selecting the desired folder by cueing the first file of each

folder Press and hold The first 10 seconds of the first file in the each folder will be played. When the desired folder is reached, press the switch once again.

until you hear a beep.

or

n Returning to the first folder

Press and hold “∨” on

or

until you hear a beep.

Selecting and scanning files

n Selecting one file at a time

To select the desired file, turn

or

or press “∧” or “∨” on

or

188

3-2. Using the audio system

n Scanning the desired file by cueing the files in the folder

or

Press The first 10 seconds of all files in the folder will be played. When the desired file is reached, press the switch once again.

Fast-forwarding and reversing files

To fast-forward or reverse. Type A: Press and hold Type B: Press and hold

) or ) or

). ).

Repeat play

n Repeating a track

Press

(RPT) or

(RPT).

n Repeating all of the files in the folder

Press and hold

(RPT) or

(RPT) until you hear a beep.

Random playback

n To play files from a particular folder in random order

Press

(RAND) or

(RAND).

n To play all of the files on a disc in random order

(RAND) or

(RAND) until you hear a

Press and hold beep.

Switching the display

Press

or

Each time the switch is pressed, the display changes in the order of Folder no./File no./Elapsed time→Folder name→File name→Album title (MP3 only)→Track title→Artist name.

189

3-2. Using the audio system

n Display

Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding 1 second or more will display the remaining characters. A maximum of 24 characters can be displayed. If is pressed for 1 second or more again or has not been pressed for 6 seconds or more, the display will return to the first 12 charac- ters. Depending on the contents recorded, the characters may not be displayed properly or may not be displayed at all.

or

for

or

n Canceling random playback

Press

(RAND) or

(RAND) again.

n Canceling repeat play (RPT) or

Press

n Error messages

(RPT) again.

“ERROR”: This indicates a trouble either in the CD or inside the player.

The CD may be dirty, damaged or inserted up-side down.

“NO MUSIC”:This indicates that the MP3/WMA file is not included in the CD.

n Discs that can be used

Discs with the marks shown below can be used. Playback may not be possible depending on recording format or disc fea- tures, or due to scratches, dirt or deterioration.

n CD player protection feature

To protect the internal components, playback is automatically stopped when a problem is detected while the CD player is being used.

n If CDs are left inside the CD player or in the ejected position for

extended periods CDs may be damaged and may not play properly.

190

3-2. Using the audio system

n Lens cleaners

Do not use lens cleaners. Doing so may damage the CD player.

n MP3 and WMA files

MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media TM Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3
format. There is a limit to the MP3 and WMA file standards and to the media/formats recorded by them that can be used. l MP3 file compatibility

• Compatible standards

MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3)

• Compatible sampling frequencies

MPEG1 LAYER3: 32, 44.1, 48 (kHz) MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz) • Compatible bit rates (compatible with VBR)

MPEG1 LAYER3: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps) MPEG2 LSF LAYER3: 64, 80, 96, 112, 128, 144, 160 (kbps)

• Compatible channel modes: stereo, joint stereo, dual channel and

monaural

l WMA file compatibility

• Compatible standards

WMA Ver. 7, 8, 9

• Compatible sampling frequencies

32, 44.1, 48 (kHz)

• Compatible bit rates (only compatible with 2-channel playback)

Ver. 7, 8: CBR 48, 64, 80, 96, 128, 160, 192 (kbps) Ver. 9: CBR 48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)

l Compatible media

Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.

191

3-2. Using the audio system

l Compatible disc formats

The following disc formats can be used. • Disc formats: CD-ROM Mode 1 and Mode 2

CD-ROM XA Mode 2, Form 1 and Form 2
• File formats: ISO9660 Level 1, Level 2, (Romeo, Joliet)

MP3 and WMA files written in any format other than those listed above may not play correctly, and their file names and folder names may not be displayed correctly.

Items related to standards and limitations are as follows. • Maximum directory hierarchy: 8 levels • Maximum length of folder names/file names: 32 characters • Maximum number of folders: 192 (including the root) • Maximum number of files per disc: 255

l File names

The only files that can be recognized as MP3/WMA and played are those with the extension .mp3 or .wma.

l Multi-sessions

As the audio system is compatible with multi-sessions, it is possible to play discs that contain MP3 and WMA files. However, only the first session can be played. ID3 and WMA tags ID3 tags can be added to MP3 files, making it possible to record the track title and artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags. (The number of characters is based on ID3 Ver. 1.0 and 1.1.) WMA tags can be added to WMA files, making it possible to record the track title and artist name in the same way as with ID3 tags.

l MP3 and WMA playback

When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played. To make the file check finish more quickly, we recommend you do not write in any files other than MP3 or WMA files or create any unnec- essary folders. If the discs contain a mixture of music data and MP3 or WMA format data, only music data can be played.

192

3-2. Using the audio system

l Extensions

If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.

l Playback

• To play MP3 file with steady sound quality, we recommend a fixed bit

rate of 128 kbps and a sampling frequency of 44.1 kHz.

• CD-R or CD-RW playback may not be possible in some instances,

depending on the characteristics of the disc.

• There is a wide variety of freeware and other encoding software for MP3 and WMA files on the market, and depending on the status of the encoding and the file format, poor sound quality or noise at the start of playback may result. In some cases, playback may not be possible at all.

• When files other than MP3 or WMA files are recorded on a disc, it may take more time to recognize the disc and in some cases, playback may not be possible at all.

• Microsoft, Windows, and Windows Media are the registered trade-

marks of Microsoft Corporation in the U.S. and other countries.

NOTICE

n CDs and adapters that cannot be used (→P. 185) n CD player precautions (→P. 186)

193

3-2. Using the audio system Optimal use of the audio system

Type A

Type B

Displays the current mode Changes the following set- ting Sound quality and volume balance (→P. 195) The sound quality and bal- ance setting can be changed to produce the best sound.

Using the AUDIO CONTROL function

n Changing sound quality modes

Pressing

or

selects the mode to be changed in the

following order. BAS → TRE → FAD → BAL → ASL* *: Type B only

194

Shifts to

front

Shifts to

right

3-2. Using the audio system

n Adjusting sound quality

Turning

or

adjusts the level.

Sound qual-

ity mode

Mode displayed

Level

-5 to 5
-5 to 5

Turn to the

left

Turn to the

right

Low

High

R7 to F7

Shifts to rear

BAS TRE

FAD

Bass Treble

Front/rear volume balance Left/right volume balance

BAL

L7 to R7

Shifts to left

n Adjusting the Automatic Sound Levelizer (ASL) (Type B only)

When “ASL” is selected, turning “ASL” level in the order of “LOW”, “MID” and “HIGH”.

to the right changes the

Turning

to the left turns “ASL” off.

ASL automatically adjusts the volume and tone quality according to vehi- cle speed.

n Trademark owned by SRS Labs, Inc.

The audio systems utilize SRS FOCUS and SRS TruBass audio enhancement technologies, under license from SRS Labs, Inc., in all modes except AM radio mode.

FOCUS, TruBass, SRS and Inc. FOCUS and TruBass technologies are incorporated under license from SRS Labs, Inc.

symbols are trademarks of SRS Labs,

195

3-2. Using the audio system Using the AUX adapter∗

This adapter can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers.

Connect the portable audio device.

Type A

Type B

Press

Press

196

∗: If equipped

3-2. Using the audio system

n Operating portable audio devices connected to the audio system

The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio device itself.

n When using a portable audio device connected to the power outlet or

cigarette lighter Noise may occur during playback. Use the power source of the portable audio device.

197

3-3. Using the interior lights Interior lights list

Interior light (→P. 199) Personal lights (→P. 199)

n Illuminated entry system

When the interior light switch is in the DOOR position, the interior light auto- matically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed and the engine switch position.

n To prevent the battery from being discharged

If the interior light remains on when the door is not fully closed and the inte- rior light switch is in the DOOR position, the light will go off automatically after 20 minutes.

n Customization that can be configured at Toyota dealer

Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 359)

198

Interior light

3-3. Using the interior lights

Interior light and personal lights

ON OFF DOOR position

Personal lights

On/off

199

3-4. Using the storage features List of storage features

Cup holders Glove box Bottle holders Console box Auxiliary box

CAUTION

n Items that should not be left in the storage spaces

Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: l Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

l Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.

200

3-4. Using the storage features

Glove box and console box

Glove box

Pull up the lever.

CAUTION

n Caution while driving

Keep the glove box closed. Injuries may result in the event of an accident or sudden braking.

Console box

Lift the lid while pulling the lever.

201