2009 Toyota Tacoma Owners Manual

465

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 466 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Access Cab models

This number Certification Label.

is also on

the

n Engine number The engine number is stamped on the engine block as shown.

2.7 L 4-cylinder (2TR-FE) engine

4.0 L V6 (1GR-FE) engine

466

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 467 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Engine

2.7 L 4-cylinder (2TR-FE) engine

Model Type Bore and stroke Displacement Drive belt tension Valve clearance (engine cold) 　Intake 　Exhaust

2TR-FE 4-cylinder in line, 4-cycle, gasoline 3.74 × 3.74 in. (95.0 × 95.0 mm) 164.3 cu.in. (2694 cm3) Automatic adjustment

Automatic adjustment

4.0 L V6 (1GR-FE) engine

1GR-FE 6-cylinder V type, 4-cycle, gasoline 3.70 × 3.74 in. (94.0 × 95.0 mm) 241.4 cu.in. (3956 cm3) Automatic adjustment

0.006 ⎯ 0.010 in. (0.15 ⎯ 0.25 mm) 0.011 ⎯ 0.015 in. (0.29 ⎯ 0.39 mm)

Unleaded gasoline only 87 (Research octane number 91) or higher

21.1 gal. (80.0 L, 17.6 lmp.gal.)

467

Model Type Bore and stroke Displacement Drive belt tension Valve clearance (engine cold) 　Intake 　Exhaust

Fuel

Fuel type Octane rating Fuel tank capacity (Reference)

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 468 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Lubrication system

2.7 L 4-cylinder (2TR-FE) engine

Oil capacity drain and refill (Reference) With filter

Without filter

Oil grade

Recommended oil viscosity

6.1 qt. (5.8 L, 5.1 Imp.qt.)

5.4 qt. (5.1 L, 4.5 Imp.qt.) ILSAC multigrade engine oil Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and viscosity shown below.

Outside temperature

Oil viscosity l The 0W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

l The 20 in 0W-20 indicates the oil viscosity when the oil is at its operating temperature. An oil with a higher viscosity may be better suited if the vehicle is operated at high speeds, or under extreme load condition.

468

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 469 Tuesday, April 8, 2008 9:01 AM

4.0 L V6 (1GR-FE) engine

6-1. Specifications

Oil capacity drain and refill (Reference)

2WD models except PreRunner

4WD models and PreRunner

Oil grade

Recommended oil viscosity

With filter 4.8 qt. (4.5 L, 4.0 Imp.qt.) Without filter 4.4 qt. (4.2 L, 3.7 Imp.qt.) With filter 5.5 qt. (5.2 L, 4.6 Imp.qt.) Without filter 5.2 qt. (4.9 L, 4.3 Imp.qt.) ILSAC multigrade engine oil Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and viscosity shown below.

Outside temperature

*: 5W-30 is an oil that provides optimal levels of fuel efficiency. Oil viscosity l The 5W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

l The 30 in 5W-30 indicates the oil viscosity when the oil is at its operating temperature. An oil with a higher viscosity may be better suited if the vehicle is operated at high speeds, or under extreme load condition.

469

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 470 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Cooling system

Capacity

2.7 L 4-cylinder (2TR-FE) engine

4.0 L V6 (1GR-FE) engine

Coolant type

Ignition system

Spark plug

2.7 L 4-cylinder (2TR-FE) engine

Make

Gap

Make

Gap

DENSO NGK

DENSO NGK

4.0 L V6 (1GR-FE) engine

Vehicles with an automatic transmission 9.1 qt. (8.6 L, 7.6 Imp.qt.) Vehicles with a manual transmission 9.1 qt. (8.7 L, 7.6 Imp.qt.) Vehicles with an automatic transmission 10.1 qt. (9.6 L, 8.5 Imp.qt.) Vehicles with a manual transmission 10.3 qt. (9.7 L, 8.5 Imp.qt.)

Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.

SK20HR11
ILFR6C11
0.043 in. (1.1 mm)

K20HR-U11
LFR6C11
0.043 in. (1.1 mm)

NOTICE

n Iridium-tipped spark plugs (2.7 L 4-cylinder [2TR-FE] engine only)

Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine.

470

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 471 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Electrical system

Battery Open voltage at 68°F (20°C):

Charging rates

Differential

12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (Voltage checked 20 minutes after the key is removed with all the lights turned off) 5 A max.

Front (4WD models)

1.59 qt. (1.50 L, 1.32 Imp.qt.)

Oil capacity

Rear

Oil type and viscosity

2WD models except PreRunner 3.66 qt. (3.46 L, 3.04 Imp.qt.) 4WD models and PreRunner 3.12 qt. (2.95 L, 2.60 Imp.qt.)

Toyota Genuine Differential Gear Oil LT 75W-85 GL-5 or equivalent “Toyota Genuine Differential Gear Oil” is filled in your Toyota vehicle at factory fill. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent of matching quality to satisfy the above specification. Please contact your Toyota dealer for further details.

471

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 472 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Automatic transmission

4-speed models

Fluid capacity (Drain and refill) Fluid type

5-speed models Fluid capacity * Fluid type

2.9 qt. (2.7 L, 2.4 Imp.qt.)

Toyota Genuine ATF Type T-IV

11.5 qt. (10.9 L, 9.6 Imp.qt.) Toyota Genuine ATF WS

*: The fluid capacity is the quantity of reference. If replacement is necessary,

contact your Toyota dealer.

NOTICE

n Automatic transmission fluid type (4-speed models)

Using automatic transmission fluid other than “Toyota Genuine ATF Type T- IV” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmission of your vehicle.

n Automatic transmission fluid type (5-speed models)

Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmission of your vehicle.

472

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 473 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Manual transmission

Gear oil capacity (Reference)

2.7 L 4-cylinder (2TR-FE) engine

4.0 L V6 (1GR-FE) engine

Gear oil type Recommended gear oil viscosity

Clutch

Clutch free play Fluid type

Transfer (4WD models)

2WD models 2.7 qt. (2.6 L, 2.3 Imp.qt.) 4WD models 2.3 qt. (2.2 L, 1.9 Imp.qt.)

1.9 qt. (1.8 L, 1.6 Imp.qt.) Gear oil API GL-4 or GL-5
SAE 75W-90

0.2 ⎯ 0.6 in. (5 ⎯ 15 mm) FMVSS No. 116 DOT 3 or SAE J1703

Oil capacity Oil type Recommended oil viscosity

1.1 qt. (1.0 L, 0.9 Imp.qt.) Gear oil API GL-4 or GL-5
SAE 75W-90

473

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 474 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Brakes

Pedal clearance *1

2WD models except PreRunner PreRunner 4WD models

4.3 in. (110 mm)

4.2 in. (106 mm)

Without off-road package 4.2 in. (106 mm) With off-road package 3.4 in. (88 mm)

0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) 0.04 in. (1.0 mm) 0.04 in. (1.0 mm)

Pedal free play Brake pad wear limit Brake lining wear limit Parking brake pedal travel *2 (pedal type) Parking brake lever travel *3 (lever type) Fluid type *1: Minimum pedal clearance when depressed with a force of 110 lbf (490 N,

FMVSS No. 116 DOT 3 or SAE J1703

7 — 10 clicks

7 — 10 clicks

50 kgf) with the engine running.

*2: Parking brake pedal travel when depressed with a force of 67.4 lbf (300 N,

30.6 kgf).

*3: Parking brake lever travel when pulled with a force of 44.9 lbf (200 N, 20.4

kgf).

474

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 475 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Chassis lubrication

Propeller shafts Spider

Lithium base chassis grease, NLGI No.2

Slide yoke

Molybdenum — disulfide lithium base chassis grease, NLGI No.2 or lithium base chassis grease, NLGI No.2

Steering

Free play

Power steering fluid type

Tires and wheels

Type A

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Less than 1.2 in. (30 mm) Automatic transmission fluid DEXRON® II or III

P215/70R15 97S Front tires: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear tires: 33 psi (230 kPa, 2.3 kgf/cm2 or bar) Spare tire*: 33 psi (230 kPa, 2.3 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 3 psi (20 kPa, 0.2 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 15 × 6 J, 15 × 6 JJ 85 ft·lbf (113 N·m, 11.5 kgf·m)

Wheel size Wheel nut torque *: If you affix the spare tire to a front position, please make sure to adjust

the tire to the correct inflation pressure as soon as possible.

475

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 476 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Type B

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

Type C

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

P245/75R16 109S Front tires: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Rear tires: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Spare tire: 30 psi (210 kPa, 2.1 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 3 psi (20 kPa, 0.2 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 16 × 7 J, 16 × 7 JJ 85 ft·lbf (113 N·m, 11.5 kgf·m)

P265/70R16 111T Front tires: 29 psi (200 kPa, 2.0 kgf/cm2 or bar) Rear tires: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare tire*: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 3 psi (20 kPa, 0.2 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 16 × 7 JJ 85 ft·lbf (113 N·m, 11.5 kgf·m)

Wheel size Wheel nut torque *: If you affix the spare tire to a front position, please make sure to adjust

the tire to the correct inflation pressure as soon as possible.

476

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 477 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Type D

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

Type E

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

P265/65R17 110S Front tires: 29 psi (200 kPa, 2.0 kgf/cm2 or bar) Rear tires: 29 psi (200 kPa, 2.0 kgf/cm2 or bar) Spare tire: 29 psi (200 kPa, 2.0 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 3 psi (20 kPa, 0.2 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 17 × 7 1/2 JJ 85 ft·lbf (113 N·m, 11.5 kgf·m)

P255/45R18 99V Front tires: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear tires: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Spare tire: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Driving at high speeds above 100 mph (160 km/h) (in countries where such speeds are permitted by law) Add 4 psi (30 kPa, 0.3 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall. 18 × 8 JJ 85 ft·lbf (113 N·m, 11.5 kgf·m)

477

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 478 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

Headlights Front fog lights Parking and front side marker lights

Front turn signal lights

Rear turn signal lights Back-up lights License plate lights High mounted stoplight Interior light Personal lights

— 9145

—

4157
NAK 3157A 921
168

168

— 168

60/55

42

27/8

27/8
18

Type

Exterior

Interior

A: HB2 halogen bulbs B: H10 halogen bulbs C: Wedge base bulbs (clear) D: Wedge base bulbs (amber) E: Double end bulbs

478

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 479 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications Fuel information

Your vehicle must use only unleaded gasoline. Unleaded gasoline with an Octane Rating of 87 (Research Octane Number 91) or higher required for optimum engine performance. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.

n Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

n If your engine knocks

l Consult your Toyota dealer. l You may occasionally notice light knocking for a short time while accelerating or driving uphill. This is normal and there is no need for concern.

n Gasoline quality

In very few cases, driveability problems may be caused by the brand of gasoline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

n Gasoline quality standards

l Automotive manufacturers in the US, Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.

l The WWFC consists of four categories that are based on required

emission levels. In the US, category 4 has been adopted.

l The WWFC improves air quality by lowering emissions in vehicle fleets,

and customer satisfaction through better performance.

479

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 480 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

n Toyota recommends the use of gasoline containing detergent additives l Toyota recommends the use of gasoline that contains detergent additives

to avoid build-up of engine deposits.

l All gasoline sold in the US contains detergent additives to clean and/or

keep clean intake systems.

n Toyota recommends the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxygenates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

n Toyota does not recommend blended gasoline

l Toyota allows the use of oxygenate blended gasoline where the

oxygenate content is up to 10% ethanol or 15% MTBE. If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87.

l Toyota does not recommend the use of gasoline containing methanol.

n Toyota does not recommend gasoline containing MMT

Some gasoline contains octane enhancing additive called MMT (Methylcyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

480

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 481 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

NOTICE

n Notice on gasoline quality

l Do not use leaded gasoline.

Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.

l Do not use gasohol other than that stated here.

Other gasohol may cause fuel system damage or vehicle performance problems.

l Use of unleaded gasoline with an Octane rating lower than 87 may result

in engine knocking. Persistent knocking can lead to engine damage.

n Fuel-related poor driveability

If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

n When refueling with gasohol Take care not to spill gasohol. It can damage your vehicle’s paint.

481

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 482 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications Tire information

Typical tire symbols

(→P. 484) (→P. 483) (→P. 373)

Tire size DOT and Tire Identification Number (TIN) Location of treadwear indicators Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Uniform tire quality grading For details, see “Uniform tire quality grading” that follows. Load limit at maximum cold tire inflation pressure Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.

(→P. 487) (→P. 487)

482

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 483 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. (→P. 377) Summer tire or all season tire An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.

Typical DOT and tire identification number (TIN)

manufacturer’s

Identification Number

DOT symbol* Tire (TIN) Tire identification mark Tire size code Manufacturer’s optional type code (3 or 4 letters) Manufacturing week Manufacturing year *:The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.

tire

483

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 484 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Tire size

n Typical tire size information

The illustration indicates typical tire size.

Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol (alphabet with one letter)

Section width Tire height Wheel diameter

n Tire dimensions

484

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 485 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Tire section names

Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer

Uniform tire quality grading

This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.

Your Toyota dealer will help answer any questions you may have as you read this information.

n DOT quality grades

All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

485

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 486 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

n Treadwear

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

n Traction AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turning) traction.

n Temperature A, B, C

The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

486

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 487 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Glossary of tire terminology

Tire related term

Meaning

Cold tire inflation pressure

Maximum inflation pressure

Recommended inflation pressure

Accessory weight

Curb weight

Maximum loaded vehicle weight

Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer The combined weight (in excess of those standard items which may be replaced) of transmission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory-installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight

487

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 488 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Tire related term

Normal occupant weight

Occupant distribution

Production options weight

Rim

Rim diameter (Wheel diameter) Rim size designation

Rim type designation

Rim width Vehicle capacity weight (Total load capacity)

Vehicle maximum load on the tire

Vehicle normal load on the tire

Meaning

150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows Distribution of occupants in a vehicle as specified in the third column of Table 1* below The combined weight of installed regular production options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated

Nominal diameter of the bead seat

Rim diameter and width The industry manufacturer's designation for a rim by style or code Nominal distance between rim flanges The rated cargo and luggage load plus 150 lb. (68 kg) times the vehicle's designated seating capacity The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two The load on an individual tire that is determined by distributing to each axle its share of curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1* below), and dividing it by two

488

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 489 Tuesday, April 8, 2008 9:01 AM

Tire related term

Weather side

Bead

Bead separation

Bias ply tire

Carcass

Chunking

Cord

Cord separation

Cracking

CT

Extra load tire

Groove

Innerliner

6-1. Specifications

Meaning

The surface area of the rim not covered by the inflated tire The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components in the bead A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall rubber which, when inflated, bears the load The breaking away of pieces of the tread or sidewall The strands forming the plies in the tire The parting of cords from adjacent rubber compounds Any parting within the tread, sidewall, or innerliner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire The space between two adjacent tread ribs The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire

489

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 490 Tuesday, April 8, 2008 9:01 AM

Meaning

The parting of the innerliner from cord material in the carcass (a)The sidewall that contains a whitewall, bears

white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or

(b)The outward facing sidewall of asymmetrical

tire that has a particular side that must always face outward when mounted on a vehicle

A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry for a given inflation pressure The load rating for a tire at the maximum permissible inflation pressure for that tire The maximum cold inflation pressure to which a tire may be inflated The rim on which a tire is fitted for physical dimension requirements Any parting at any junction of tread, sidewall, or innerliner that extends to cord material The overall diameter of an inflated new tire The linear distance between the exteriors of the sidewalls of an inflated tire, including elevations due to labeling, decorations, or protective bands or ribs A tire intended for use on passenger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less

6-1. Specifications

Tire related term

Innerliner separation

Intended outboard sidewall

Light truck (LT) tire

Load rating

Maximum load rating

Maximum permissible inflation pressure

Measuring rim

Open splice

Outer diameter

Overall width

Passenger car tire

490

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 491 Tuesday, April 8, 2008 9:01 AM

Tire related term

Ply

Ply separation

Pneumatic tire

Radial ply tire

Reinforced tire

Section width

Sidewall

Sidewall separation

Snow tire

Test rim

6-1. Specifications

Meaning

A layer of rubber-coated parallel cords A parting of rubber compound between adjacent plies A mechanical device made of rubber, chemicals, fabric and steel or other materials, that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire The linear distance between the exteriors of the sidewalls of an inflated tire, excluding elevations due to labeling, decoration, or protective bands That portion of a tire between the tread and bead The parting of the rubber compound from the cord material in the sidewall A tire that attains a traction index equal to or greater than 110, compared to the ASTM E- 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( ) on at least one sidewall The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire

491

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 492 Tuesday, April 8, 2008 9:01 AM

6-1. Specifications

Tire related term

Meaning

Tread

Tread rib

Tread separation

Treadwear indicators(TWI)

Wheel-holding fixture

That portion of a tire that comes into contact with the road A tread section running circumferentially around a tire Pulling away of the tread from the tire carcass The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread The fixture used to hold the wheel and tire assembly securely during testing

*:Table 1 ⎯ Occupant loading and distribution for vehicle normal load

for various designated seating capacities

Designated seating capacity, Number of

occupants 2 through 4

5 through 10

11 through 15

16 through 20

Vehicle normal load, Number of occupants

Occupant distribution in a normally loaded

vehicle 2 in front

2 in front, 1 in second

seat

2 in front, 1 in second seat, 1 in third seat, 1

in fourth seat

2 in front, 2 in second seat, 2 in third seat, 1

in fourth seat

492

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 493 Tuesday, April 8, 2008 9:01 AM

6-2. Customization Customizable features

Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by an autho- rized Toyota dealership. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details.

Item

Function

Default setting

Wireless remote con- trol (→P. 32) Seat Belt Reminder Buzzer (→P. 427)

Operation signal (Buzzer)

Vehicle speed linked seat belt reminder buzzer

ON

ON

Customized

setting

OFF

OFF

493

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 494 Tuesday, April 8, 2008 9:01 AM

6-2. Customization Items to initialize

The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle.

Item

When to initialize

Reference

Engine oil maintenance data

After changing engine oil

P. 361

Tire pressure warning sys- tem

• When rotating the tires on vehi- cles differing with front and rear tire inflation pressures. • When changing the tire inflation pressure by changing traveling speed or load weight, etc. • When changing the tire size.

P. 374

494

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 496 Tuesday, April 8, 2008 9:01 AM

Reporting safety defects for U.S. owners

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA can- not become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safer- car.gov; or write to: Administrator, NHTSA, 1200 New Jersey Ave, S.E., Washington, DC 20590. You can also obtain other informa- tion about motor vehicle safety from http://www.safercar.gov.

496

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 497 Tuesday, April 8, 2008 9:01 AM

Seat belt instructions for Canadian owners (in French)

The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.

497

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 498 Tuesday, April 8, 2008 9:01 AM

498

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 499 Tuesday, April 8, 2008 9:01 AM

Camper information

This information has been prepared in accordance with regula- tion issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchas- ers and/or prospective purchasers of Toyota vehicles with infor- mation on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this informa- tion.

Center of gravity location

The figures given in the illustration indicate the recommended center of gravity zone.

location

Recommended for cargo center of gravity for cargo weight rating Rear end of truck bed

Regular Cab models Access Cab models Except X-Runner X-Runner*

Double Cab models

With short deck With long deck

49.9 in. (1267 mm)

36.1 in. (917 mm)

49.9 in. (1267 mm)

—

36.1 in. (917 mm)

—

45.6 in. (1157 mm) 35.9 in. (911 mm)

31.8 in. (807 mm) 27.8 in. (706 mm)

*: Truck-campers cannot be used with the X-Runner since it is not

designed for them.

499

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 500 Tuesday, April 8, 2008 9:01 AM

CAUTION

n Loading precaution

If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded.

Cargo weight rating and proper matching

When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo, and the weight of passengers in the camper. The total cargo load should not exceed the truck’s cargo weight rating and the camper’s center of gravity should fall within the truck’s rec- ommended center of gravity zone when installed.

Camper center of gravity Recommended center of grav- ity location zone

n Cargo weight rating

Regular Cab models 2 people, 2TR-FE engine, 2WD except PreRunner:

3 people, 2TR-FE engine, 2WD except PreRunner:

950 lb. (430 kg)

2 people, 2TR-FE engine, PreRunner: 3 people, 2TR-FE engine, PreRunner:

800 lb. (362 kg) 1000 lb. (453 kg) 850 lb. (385 kg)

500

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 501 Tuesday, April 8, 2008 9:01 AM

2 people, 2TR-FE engine, 4WD: 3 people, 2TR-FE engine, 4WD: Access Cab models 2 people, 2TR-FE engine, 2WD except PreRunner:

1000 lb. (453 kg) 850 lb. (385 kg)

900 lb. (408 kg)

4 people, 2TR-FE engine, 2WD except PreRunner:

2 people, 2TR-FE engine, PreRunner: 4 people, 2TR-FE engine, PreRunner: 2 people, 1GR-FE engine, PreRunner: 4 people, 1GR-FE engine, PreRunner: 2 people, 2TR-FE engine, 4WD: 4 people, 2TR-FE engine, 4WD: 2 people, 1GR-FE engine, 4WD: 4 people, 1GR-FE engine, 4WD: Double Cab models with short deck 2 people, 1GR-FE engine, PreRunner: 5 people, 1GR-FE engine, PreRunner: 2 people, 1GR-FE engine, 4WD: 5 people, 1GR-FE engine, 4WD: Double Cab models with long deck 2 people, 1GR-FE engine, PreRunner: 5 people, 1GR-FE engine, PreRunner: 2 people, 1GR-FE engine, 4WD: 5 people, 1GR-FE engine, 4WD:

600 lb. (272 kg) 1000 lb. (453 kg) 700 lb. (317 kg) 1000 lb. (453 kg) 700 lb. (317 kg) 1000 lb. (453 kg) 700 lb. (317 kg) 905 lb. (410 kg) 605 lb. (274 kg)

1000 lb. (453 kg) 550 lb. (249 kg) 900 lb. (408 kg) 450 lb. (204 kg)

1000 lb. (453 kg) 550 lb. (249 kg) 800 lb. (363 kg) 350 lb. (159 kg)

CAUTION

n Overloading

Be careful — overloading can cause dangerous braking and handling problems, and can damage your vehicle and its tires.

501

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 502 Tuesday, April 8, 2008 9:01 AM

Gross axle and vehicle weight ratings

Secure loose items to prevent weight shifts that could affect the bal- ance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads. Individual axle loads should not exceed either of the Gross Axle Weight Ratings (GAWR). The total of the axle loads should not exceed the Gross Vehicle Weight Rating (GVWR). These ratings are given on the vehicle certification label which is located on the door latch post on the left side of the vehicle. (→P. 465) If weight ratings are exceeded, move or remove items to bring all weights below the ratings.

Gross axle weight rating

Front GAWR Rear GAWR

Gross vehicle weight rating

Not exceed GVWR

502

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 503 Tuesday, April 8, 2008 9:01 AM

n GAWR

2WD models except PreRun- ner

GAWR

Front

Rear

2380 lb. (1079 kg)

2685 lb. (1217 kg)

4WD models and PreRunner

2755 lb. (1249 kg)

n GVWR

2WD models except PreRunner

Regular Cab models 3000 lb. (1360 kg) Access Cab and Double Cab models 3110 lb. (1410 kg)

Cab type

Regular Cab

Access Cab

PreRunner

Cab type Regular Cab Access Cab Double Cab

GVWR

Vehicles with an automatic transmission 4650 lb. (2109 kg) Vehicles with a manual transmission 4600 lb. (2086 kg) Vehicles with 2.7 L 4-cylinder (2TR-FE) engine 4900 lb. (2222 kg) Vehicles with 4.0 L V6 (1GR-FE) engine 4700 lb. (2131 kg)

GVWR

5000 lb. (2268 kg) 5250 lb. (2381 kg) 5350 lb. (2426 kg)

503

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 504 Tuesday, April 8, 2008 9:01 AM

4WD models

Cab type Regular Cab Access Cab Double Cab

GVWR

5100 lb. (2313 kg) 5350 lb. (2426 kg) 5450 lb. (2472 kg)

504

TACOMA_U_(L/O_0805)

TACOMA_U.book Page 508 Tuesday, April 8, 2008 9:01 AM

Alphabetical index Alphabetical index

A/C.............................................220
ABS ...........................................184
Access doors .............................39
Accessory meter......................156
Active traction control system ....................................174
Air conditioning filter...............388
Air conditioning system

Air conditioning filter..............388 Manual air conditioning

system ................................220

Airbags

Airbag operating conditions.....84
Airbag precautions for your

child ......................................89
Airbag warning light...............426
Curtain shield airbag operating

conditions..............................85