Download PDF Manual

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems.


for


to


or


also


elect


emission


establishment


You may have maintenance, replacement, or repair of the control devices and system performed by any automotive repair individual without invalidating this warranty. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for complete warranty information. Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota.


356


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented on page 361 in Section 7. If skilled do−it−yourself mechanic, the Toyota service manuals are recommended. Please be aware that do−it−yourself maintenance can affect your warranty coverage. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for the details.


you are


the


items


listed,


General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.


CAUTION


Make these checks only with ade- quate ventilation if you run the en- gine.


IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See page 391 in Section 7−3 for additional information.


Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see− through reservoir when the engine is cold. See page 372 in Section 7−2 for addition- al information. Radiator, condenser and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt, or insects. See page 373 in Section 7−2 for additional information. Battery condition Check the battery condition by the indica- tor color. See page 388 in Section 7−3 for additional information. Brake fluid level Make sure the brake fluid level is correct. See page 373 in Section 7−2 for addition- al information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See page 370 in Section 7−2 for additional information. Power steering fluid level (2.7 L 4−cylinder [2TR−FE] engine) Check the level on the dipstick. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See page 375 in Section 7−2 for additional in- formation.


357


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


Power steering fluid level (4.0 L V6 [1GR−FE] engine) Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See page 375 in Section 7−2 for addition- al information. Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” on page 275 in Section 2.) INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise. 358


For


folding−down


Seats Check that all seat controls such as seat adjusters, seatback recliner, etc. operate smoothly and that all latches lock securely in any position. Check that the head re- straints move up and down smoothly and that the locks hold securely in any latched position. seatback (bench seat) and rear seatback (rear split bench seat), check that the latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure the belt webbing is not cut, frayed, worn or dam- aged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function.


Brakes In a safe place, check that the brakes do not pull to one side when applied. Parking brake (pedal type) Check that the pedal has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Parking brake (lever type) Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes released. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately.


fluid after


time


to


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


latch


the hood


the primary


latch secures


Doors and engine hood Check that all doors including tailgate op- erate smoothly and all latches lock se- curely. Make sure the engine hood sec- from ondary opening when is re- leased. Tire inflation pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See page 376 in Section 7−2
for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See page 379 in Section 7−2 for additional in- formation. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tires according to the maintenance schedule. (For sched- uled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.) See page 381 in Section 7−2
for additional information.


tip−offs


for changes


Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: D Engine missing, stumbling, or pinging D Appreciable loss of power D Strange engine noises D A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)


D Change


in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)


D Flat−looking tire; excessive tire squeal


when cornering; uneven tire wear


D Vehicle pulls to one side when driving


straight on a level road


D Strange noises related to suspension


movement


D Loss of brake effectiveness; spongy feeling brake or clutch pedal; pedal al- most touches floor; vehicle pulls to one side when braking


D Engine coolant temperature continually


higher than normal


If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.


CAUTION


Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


359


The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re−testing.


08 02.19


indicator


the malfunction


in- include OBD


Emissions Inspection and Maintenance (I/M) programs Some states have vehicle emission spection programs which (On−Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the battery is disconnected or run down, the codes are erased. Also, depending on your driving habits, the codes may not be completely set. Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test.


the malfunction


indicator


test as


I/M


the


if


360


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


SECTION 7− 1


DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do−it−yourself service precautions Parts and tools


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


362
364
364
366


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


361


08 02.19


Engine compartment overview "2.7 L 4−cylinder (2TR−FE) engine


1. Windshield washer fluid tank 2. Engine coolant reservoir 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil level dipstick 6. Brake fluid reservoir 7. Fuse block 8. Battery 9. Condenser 10. Radiator


LS71002b


362


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


"4.0 L V6 (1GR−FE) engine


1. Windshield washer fluid tank 2. Power steering fluid reservoir 3. Engine oil level dipstick 4. Engine coolant reservoir 5. Engine oil filler cap 6. Brake fluid reservoir 7. Fuse block 8. Battery 9. Condenser 10. Radiator


LS71001b


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


363


08 02.19


Fuse locations


LS71003


Spare fuses


LS71004


LS71005


Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This Section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools” on page 366 in this Section. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:


instructions only


364


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


CAUTION


D When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)


(Removing


belts.


D Right after driving,


the engine compartment—the engine, radiator, exhaust manifold, power steering fluid reservoir and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot. D If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.


D Do not


leave anything


that may burn easily, such as paper or rags, in the engine compartment.


D Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.


D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your thoroughly with soap skin, wash and water.


D Do not


leave used oil within the


reach of children.


D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.


for


D Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.


NOTICE


z Remember that battery and ignition coil carry high currents or voltages. Be careful of accidentally causing a short circuit.


z Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).


z If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.


z Do not allow dirt or anything else to fall through the spark plug holes. z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


365


08 02.19


z Do not reuse iridium−tipped spark


plugs by cleaning or regapping.


z Do not overfill automatic transmis- transmission


fluid, or


the


sion could be damaged.


z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.


z Be careful not to scratch the glass


surface with the wiper frame.


z When closing


the engine hood, check to see that you have not for- gotten any tools, rags, etc.


Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): D “Toyota Genuine Motor Oil” or equiva-


lent See page 370 in Section 7−2 for de- tails about engine oil selection.


Tools: D Rag or paper towel D Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): D “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water(for the U.S.A.) or 55% cool- ant and 45% deionized water (for Can- ada).


Tools: D Funnel (only for adding coolant) CHECKING BRAKE FLUID Parts (if level is low): D SAE J1703 or FMVSS No.116 DOT 3


brake fluid


Tools: D Rag or paper towel D Funnel (only for adding fluid) CHECKING POWER STEERING FLUID Parts (if level is low): D Automatic


transmission


fluid


DEXRONrII or III


Tools: D Rag or paper towel D Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: D Warm water D Baking soda D Grease D Conventional wrench


(for


terminal


clamp bolts)


366


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


CHECKING AND REPLACING FUSES Parts (if replacement is necessary): D Fuse with same amperage rating as


original


ADDING WASHER FLUID Parts: D Water D Washer fluid containing antifreeze


(for winter use)


Tools: D Funnel REPLACING LIGHT BULBS Parts: D Bulb with same number and wattage rating as original in “Replacing light bulbs” on page 392 in Section 7−3.)


charts


(See


Tools: D Screwdriver D Wrench


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


367


08 02.19


368


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


SECTION 7− 2


DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking the radiator and condenser Checking brake fluid Checking power steering fluid Checking tire inflation pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


370
372
373
373
375
376
379
381
382
384
385


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


369


08 02.19


Checking the engine oil level


Low level


Full level


LS72005


Add oil


O.K.


Too full


2TR−FE engine


Low level


Full level


LS72004


With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a correct reading, the vehicle should be on level ground. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.


2. Pull the dipstick out, hold a rag under


the end and wipe it clean.


3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.


4. Pull the dipstick out and look at the oil the


level while holding a rag under end.


CAUTION


If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. We recommend that you use a funnel when adding oil. The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows:


2.7 L 4−cylinder (2TR−FE) engine


1.3 L (1.4 qt., 1.1 Imp.qt.)


4.0 L V6 (1GR−FE) engine


1.5 L (1.6 qt., 1.3 Imp.qt.) For the engine oil capacity, see “Service specifications” on page 406 in Section 8. When the level reaches within the correct range, install the filler cap hand−tight.


Be careful not to touch the hot ex- haust manifold.


NOTICE


Add oil


O.K.


Too full


Be careful not to drop engine oil on the vehicle components.


NOTICE


1GR−FE engine


370


z Be careful not to spill engine oil on


the vehicle components.


z Avoid overfilling, or


could be damaged.


the engine


z Check the oil level on the dipstick


once again after adding the oil.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


ENGINE OIL SELECTION “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscos- ity. Oil grade:


is used


ILSAC multigrade engine oil


Recommended viscosity:


2.7 L 4−cylinder (2TR−FE) engine—


SAE 5W−20 or 0W−20


SOIL20


Outside temperature


SAE 5W−20 or 0W−20 engine oil may be used. However, SAE 0W−20 is the best choice for good fuel economy and good starting in cold weather.


4.0 L V6 (1GR−FE) engine—


SAE 5W−30


Outside temperature


SAE 5W−30 is the best choice for good fuel economy, and good starting in cold weather. If SAE 5W−30 oil is not available, SAE 10W−30 oil may be used. However, it should be replaced with SAE 5W−30 at the next oil change.


Oil identification mark The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is added to some oil con- tainers the oil you should use.


to help you select


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


371


08 02.19


To ensure excellent lubrication perfor- mance for your engine, “Toyota Genuine Motor Oil” is available, which has been specifically for all Toyota engines. Please contact your Toyota dealer for fur- ther details about “Toyota Genuine Motor Oil”.


tested and approved


(For


the coolant


Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add the coolant. type, see “Coolant type selection” described be- low.) The coolant level in the reservoir will vary with engine temperature. However, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.


the system. Visually check


in


is a


hybrid


organic


long−life


improper coolants may damage


Coolant type selection Use of your engine cooling system. Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life technology. (Coolant hybrid organic acid acid with technology low phosphates and organic acids.) For the U.S.A.—“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water. This coolant pro- vides protection down to about −35_C (−31_F). For Canada—“Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deionized water. This coolant pro- vides protection down to about −42_C (−44_F).


combination of


CAUTION


NOTICE


To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.


Do not use plain water alone.


372


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


Toyota recommends “Toyota Super Long Life Coolant”, which has been tested to ensure that it will not cause corrosion nor result in malfunction of your engine coolant system with proper usage. “Toyota formulated Super Long Life Coolant” with acid technology and has been specifically designed to avoid engine cooling system malfunction on Toyota vehicles. Please contact your Toyota dealer further details.


is organic


long−life


hybrid


for


Checking the radiator and condenser If either of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer.


CAUTION


To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.


NOTICE


To prevent damage to the radiator and condenser, do not perform the work by yourself.


Checking brake fluid (without vehicle stability control system)


LS72007


reservoir. The


To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem. If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


373


08 02.19


Remove and replace the reservoir cap by hand. Fill the brake fluid to the dotted line. This brings the fluid to the correct level when you put the cap back on. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.


CAUTION


Take care when filling the reservoir because brake fluid can harm your hands or eyes. If fluid gets on your hands or in your eyes, flush the af- fected area with clean water immedi- ately. If you still feel uncomfortable with your hands or eyes, go to the doctor.


NOTICE


If you spill some of the fluid, be sure to wipe it off to prevent it from dam- aging the parts or paintwork.


374


Checking brake fluid (with vehicle stability control system)


LS72006


reservoir. The


To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem. If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir.


Refilling brake fluid: 1. Turn the engine switch off. 2. Depress the brake pedal more than 20


times.


3. Remove the reservoir cover by hand. Add brake fluid up to the “MAX” line. If you do not follow the procedure above, the reservoir may overflow. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.


CAUTION


Take care when filling the reservoir because brake fluid can harm your hands or eyes. If fluid gets on your hands or in your eyes, flush the af- fected area with clean water immedi- ately. If you still feel uncomfortable with your hands or eyes, go to the doctor.


NOTICE


If you spill some of the fluid, be sure to wipe it off to prevent it from dam- aging the parts or paintwork.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


Checking power steering fluid (2.7 L 4−cylinder [2TR−FE] engine)


If cold add


If cold O.K.


LS72009


If hot add


If hot O.K.


Check the fluid level on the dipstick. If necessary, add automatic transmission fluid DEXRONrII or III. If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (40_C—80_C or 104_F—175_F). You may also check the level when the fluid is temperature, 0_C—40_C or 32_F—104_F) if the engine has not been run for about five hours. a. Clean all dirt from outside of the reser-


(about


room


cold


c. Reinstall the reservoir cap. d. Remove the reservoir cap again and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range on the dipstick. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic transmission fluid DEXRONrII or III to bring the level within the range.


e. After replacing the reservoir cap, visu- ally check the steering box case, vane pump and hose connections for leaks or damage.


CAUTION


The reservoir tank may be hot so be careful not to burn yourself.


NOTICE


Avoid overfilling, or the power steer- ing could be damaged.


Checking power steering fluid (4.0 L V6 [1GR−FE] engine)


If cold O.K.


If cold add


Open


Close


LS72008


If hot O.K.


If hot add


III.


Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRONrII or If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60_C—80_C or 140_F—175_F). You may also check the level when the fluid is temperature, 10_C—30_C or 50_F—85_F) if the engine has not been run for about five hours.


(about


room


cold


voir tank.


b. Remove the reservoir cap by turning it counterclockwise and wipe the dipstick clean.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


375


08 02.19


Checking tire inflation pressure


Clean all dirt from the outside of the res- ervoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRONrII or III to bring the level within the range. To remove the reservoir cap, turn it coun- terclockwise and it, turn it clockwise. After replacing the reser- voir cap, visually check the steering box case, vane pump and hose connections for leaks or damage.


lift up. To reinstall


transmission


LS72020a


LS72021a


CAUTION


The reservoir tank may be hot so be careful not to burn yourself.


NOTICE


Avoid overfilling, or the power steer- ing could be damaged.


376


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


Regular and double cab models


Access cab models


08 02.19


Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on page 402 in Section 8. They are also described on the tire and label as shown. You should check the tire inflation pressure every two weeks, or at least once a month. And do not forget the spare!


information


loading


should


pressure


following


instructions


The for checking tire inflation pressure should be observed: D The


be checked only when the tires are cold. If your vehicle has been parked for at least 3 hours and has not been driven for more than 1.5
km or 1 mile since, you will get an accurate cold tire inflation pres- sure reading.


Tire pressure gauge


LS72003


D Always use a tire pressure gauge. The appearance of a tire can be misleading. Besides, tire inflation pressures that are even just a few pounds off can degrade ride and handling.


D Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving. D Never exceed the vehicle capac- ity weight. Passenger and lug- gage weight should be located so that the vehicle is balanced.


INSPECTION AND ADJUSTMENT PROCEDURE 1. Remove the tire valve cap. 2. Press the tip of the tire pressure


gauge to the tire valve.


3. Read the pressure using the grad-


uations of the gauge.


4. In case the tire inflation pressure is not within the prescribed range, insert the compressed air from the valve. In case of applying too much air, press the center of the valve and release the air to adjust.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


377


08 02.19


5. After completing the tire inflation pressure measurement and ad- justment, apply soapy water to the valve and check for leakage.


6. Install the tire valve cap. If a gauge and air pump are not avail- able, have your vehicle checked by your Toyota dealer.


CAUTION


Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as pos- sible.


Incorrect tire inflation pressure may waste fuel, reduce the comfort of driv- ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal- er.


378


High tire pressure (overinfla- tion)— D Poor handling D Excessive wear D Uneven wear D A greater possibility of tire


damage from road hazards


CAUTION


Keep your tires properly inflated. Otherwise, the following condi- tions may occur and cause an ac- cident resulting in death or seri- ous injuries. Low tire pressure (underinfla- tion)— D Excessive wear D Uneven wear D Poor handling D Possibility of blowouts from an


overheated tire


D Poor sealing of the tire bead D Wheel deformation and/or tire


separation


D A greater possibility of tire


damage from road hazards


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


Checking and replacing tires


Treadwear indicator


CHECKING YOUR TIRES Check the tire’s tread for treadwear indicators. If the indicators show, replace the tires. The location of treadwear indicators is shown by the “TWI” or “Δ” marks, etc., molded on the sidewall of each tire.


If air loss occurs while driving, do not continue driving. Driving even a short distance can damage a tire beyond repair. Any tires which are over 6 years old must be checked by a qualified technician even if damage is not obvious. Tires deteriorate with age even if they have never or seldom been used. This applies also to the spare tire and tires stored for future use.


The tires on your Toyota have built−in treadwear indicators to help you know when the tires need replacement. When the tread depth wears to 1.6
mm (0.06 in.) or less, the indicators will appear. If you can see the indica- tors in two or more adjacent grooves, the tire should be replaced. The lower the tread, the higher the risk of skid- ding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.). If you have tire damage such as cuts, splits, cracks deep enough to expose the fabric, or bulges indi- cating internal damage, the tire should be replaced. If a tire often goes flat or cannot be properly repaired due to the size or location of a cut or other damage, it should be replaced. If you are not sure, consult with your Toyota dealer.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


379


08 02.19


For details about the sidewall of the tire and the Certification Label, see “Tire information” on page 287 in Sec- tion 2 and “Your Toyota’s identifica- tion” on page 284 in Section 2.


CAUTION


Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. D Do not mix radial, bias belted, or bias−ply tires on your ve- hicle, as this may cause dan- gerous handling characteris- tics resulting in loss of control. D Do not use tires other than the manufacturer’s recommended size, as this may cause danger- ous handling characteristics resulting in loss of control.


REPLACING YOUR TIRES When replacing a tire, use a tire of the same size and construction, and the same or greater maximum load as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Using any other size or type of tire may seriously affect handling, ride, speedometer/odometer calibration, ground clearance, and clearance be- tween the body and tires or snow chains. Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Cer- tification Label.


380


D Four−wheel drive models:


Do not use tires of different brands, sizes, construction or tread patterns, as this may cause dangerous handling characteristics in loss of control.


resulting


Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” on page 329 in Section 4 for tire change proce- dure. When a tire is replaced, the wheel should always be balanced. An unbalanced wheel may affect ve- hicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


initialized when


The tire pressure warning system must be the specified tire inflation pressure is changed due to tire replacement. See “Tire pressure warning system” on page 194 in Section 1−7.


NOTICE


z When the tires must be re- paired or replaced, have them repaired or replaced by the nearest Toyota dealer or au- thorized tire dealer. Failure to do so may cause the tire pressure sensors to be dam- aged when the tires are re- moved or installed.


z Remove the air pressure sen- sors before the tires to prevent the sensors from being damaged.


replacing


Rotating tires


LS72010


LS72012


With a spare tire of the same wheel type as the installed tires


With a spare tire of different wheel type from the installed tires


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


381


08 02.19


to


the


tire


life,


(For


To equalize the wear and help extend Toyota recommends that you rotate your tires according to the maintenance schedule. scheduled maintenance information, please refer “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) However, the most appropriate timing for tire rotation may vary according to your driving habits and road surface conditions. See “If you have a flat tire” on page 329 in Section 4 for tire change proce- dure. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking.


The tire pressure warning system must be initialized when rotating tires, in case that specified tire inflation pressure is different between front and rear. See “Tire pressure warning system” on page 194 in Section 1−7.


Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.


CAUTION


the


following


Observe instructions. Otherwise, an accident may occur re- sulting in death or serious injuries. D Do not use snow tires other than the manufacturer’s recommended si- ze, as this may cause dangerous handling characteristics resulting in loss of control.


382


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


D Four−wheel drive models:


Do not use snow tires of different brands, sizes, construction or tread patterns, as this may cause danger- ous handling characteristics result- ing in loss of control.


SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the rear wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires, you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replacing.


CAUTION


D Do not drive with the snow tires


incorrectly inflated.


D Never drive over 120 km/h (75 mph)


with any type of snow tires.


Side chain


G72017


Cross chain


TIRE CHAIN SELECTION Use the tire chains of correct size. Use the following type chains.


mm (in.) 5.0 (0.20) A Diameter of side chain: B Diameter of cross chain: 6.3 (0.25) Regulations regarding the use of tire chains vary according to location or type of road, so always check local reg- ulations before installing chains.


NOTICE


If the wrong combination of tire and chain is used, the chains could dam- age the vehicle body.


the


front driving


CHAIN INSTALLATION Install the chains on the rear tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.


0.5—1.0


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


383


08 02.19


CAUTION


D Do not exceed 50 km/h (30 mph) or recom- is


the chain manufacturer’s mended speed lower.


limit, whichever


D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.


D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.


D When driving with chains installed, to drive carefully. Slow be sure down before entering curves to avoid losing control of the vehicle. Otherwise an accident may occur.


NOTICE


Snow tires or chains may affect the tire pressure warning system. See “Tire pressure warning system” on page 194 in Section 1−7.


Replacing wheels As you might have difficulty in identify- ing a flat or deflated tire, a tire pres- sure warning system is provided on this vehicle. When replacing the wheels, be sure to install tire pressure warning valves and transmitters on the wheels. Consult your Toyota dealer about how to set up the tire pressure warning valves and transmitters.


CAUTION


D Have the tires, wheels or tire pres- sure warning valves and transmit- ters replaced and ID codes regis- tered by Toyota dealer. If you need tire pressure warning valves and transmitters, purchase from Toyota dealer.


D The tire pressure warning valve and transmitter nuts should always be tightened to a torque of 4 N·m (0.4
kgf·m, 2.9 ft·lbf).


D The use of non−genuine wheels may result in the tire pressure warning system failure or air−leak.


WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace a damaged wheel, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.


384


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.


CAUTION


the


following


instructions. Observe Otherwise, an accident may occur re- sulting in death or serious injuries. D Do not use wheels other than the manufacturer’s recommended size, as this may cause dangerous han- dling characteristics in loss of control.


resulting


D Four−wheel drive models:


Do not use wheels of different brands, sizes and types, as this may cause dangerous handling characteristics resulting in loss of control.


The tire pressure warning system must initialized when the specified tire be inflation pressure is changed due to wheel replacement. See “Tire pressure warning system” on page 194 in Section 1−7.


NOTICE


the air pressure sensors


The use of non−genuine wheels will cause to transmit the electronic code in differ- ent manner, resulting in the system failure.


installing that


the wheel nuts are


Aluminum wheel precautions D When aluminum wheels, check tight after driving your vehicle the first 1600
km (1000 miles). Retorque the wheel nuts to 113 N·m (11.5 kgf·m, 85 ft·lbf). repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles). Retorque the wheel nuts to 113 N·m (11.5 kgf·m, 85
ft·lbf).


rotated, tires, check


that


D When using tire chains, be careful not


to damage the aluminum wheels.


D Use only Toyota wheel nuts and for your aluminum


wrench designed wheels.


D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.


D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


385


08 02.19


386


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


SECTION 7− 3


DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


388
389
390
391
392


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


387


08 02.19


Checking battery condition— —Precautions


CAUTION


BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-


tery with tools.


D Do not smoke or light a match near


the battery.


The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or


clothes.


D Never ingest electrolyte. D Wear protective safety glasses when


working near the battery.


D Keep children away from the bat-


tery.


EMERGENCY MEASURES D If electrolyte gets


in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.


and get


D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.


D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.


D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.


—Checking battery exterior


Terminals


Ground cable


LS73001a


Hold−down clamp


Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.


b. If the terminal connections are loose, their clamp nuts—but do not


tighten overtighten.


c. Tighten


the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.


388


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


08 02.19


NOTICE


z Be sure the engine and all accesso- ries are off before performing main- tenance.


z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.


z Be careful not to cause a short cir-


cuit with tools.


z Take care no solution gets into the


battery when washing it.


—Checking battery fluid


Type A


Green


Dark


Clear or light yellow


Type B


Blue


White


Red


CHECKING BY INDICATOR Check the battery condition by the indi- cator color.


Indicator color


Type A Type B


Green


Blue


Dark


White


Clear or


light yellow


Red


Condition


Good


Charging necessary. Have battery checked by your Toyota dealer.


Have battery checked by your Toyota dealer.


Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.


2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.


is off when connecting


CAUTION


D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.


D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.


NOTICE


Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.


2008 TACOMA from Apr. ’08 Prod. (OM35898U)


389


08 02.19


Checking and replacing fuses


LS73002


Good


Blown


LS73024


LS73004a


Good


Blown


Type A


Type C


LS73003


LS73023


Good


Blown


Good


Blown

Loading...
x