in case of an accident or a sudden stop, always keep the glove box door closed while driving.
injury
The box is designed to store a garage door opener transmitter. Open the cover and remove the hook- and - loop fastener square.
252
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
LS10008
LS10009
LS10010
Remove the paper strip covering the adhe- sive on back side of square and adhere the square to back side of the transmitter near the center.
Please note if transmitter has wire clip for sun visor, this clip must be removed prior to adhesion of the fastener.
Place the transmitter with fastener square facing inside of box into the box. Make sure located above button pins.
transmitter button
the
is
2006 TACOMA from Jan.’06 Prod. (OM35871U)
253
06 04.25
LS10011
LS10012
LS10013
Remove spacers from the center panel. Place one spacer on the pin that would be below transmitter button when the cover is closed. Close the cover.
When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the center panel of the cover.
If the center panel does not contact your garage door opener transmitter: (cid:1) Check to see if spacer is on the cor-
rect pin.
(cid:1) Attach another spacer
top of original spacer. Check operation. If re- quired, continue to add spacers until contact is achieved.
to the
If the transmitter is clattering during driv- ing, fill in a piece of felt or pad to prevent the transmitter from clattering.
254
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
CAUTION
(cid:1) To reduce the chance of injury in case of an accident or a sudden stop, always keep the garage door opener box closed while driving.
(cid:1) Keep the remaining spacers away
from children.
Auxiliary boxes To use the auxiliary boxes, open the lids as shown in the following illustra- tions.
CAUTION
(cid:1) To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.
(cid:1) Type A only—As these holders are designed for holding a light object such as an eyeglass, do not place any heavy objects in them. Heavy objects may cause the holder to open and contents to fly out result- ing in injuries.
NOTICE
Type A only—During hot weather, the interior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.
LS10014
Type A (over head console)
LS10015
Type B (instrument panel)
2006 TACOMA from Jan.’06 Prod. (OM35871U)
255
06 04.25
LS10016a
Front
LS10019a
LS10018a
Type C (under the rear seat of access cab models)
Type E (left side of bed)
Type G (right side of bed)
Front
LS10017a
LS10043
Type D (under the rear seat of double cab
models)
256
Type F (right side of bed)
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
Rear console box
LS10020
LS10021
To use the rear console box, raise the console box lid while pushing the lock release button.
The rear console box is equipped with the flexible cargo net. The flexible cargo net is detachable.
Cup holders The cup holders are designed for hold- ing cups or drink- cans securely. Type A and B—The cup holder can be adjustable to the size of the cups or drink- cans by changing the holder posi- tion and the arm position, as shown.
CAUTION
Do not place anything else other than cups or drink- cans in the cup holder, as such items may be thrown about in the compartment and possibly in- jured people the vehicle during sudden braking or in an accident.
in
2006 TACOMA from Jan.’06 Prod. (OM35871U)
257
06 04.25
LS10026
LS10028
LS10027
Type C (separate seats with automatic transmission)
LS10025
Type A (bench seat)
258
Type B (separate seats with automatic transmission)
Type D (separate seats with manual trans- mission)
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
Bottle holders
LS10022
LS10024
NOTICE
Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes.
Front doors
Rear console box
The bottle holders are designed to hold bottles securely.
CAUTION
Do not attempt to use the holder for any other purpose for which it was intended. Inappropriately sized or shaped objects may be thrown about in the compartment and possibly in- jured people in the vehicle during a sudden braking or an accident.
LS10023
Rear doors (double cab models only)
2006 TACOMA from Jan.’06 Prod. (OM35871U)
259
06 04.25
Storage boxes (double cab models only)
Flashlight holder (double cab models only)
LS10031a
Separator
Type A (left side behind the rear seat back)
Separator
LS10030b
Type B (right side behind the rear seat
back)
260
This box is designed to place things like bottles. The separator is detachable, and it can be installed in various positions as required.
LS10044
is designed
flashlight holder
The hold the flashlight securely. The flashlight holder is detachable, and it can be installed in various positions as required.
to
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
Seatback table (on some models)
Cargo net hooks (double cab models with subwoofer)
NOTICE
To prevent damage to the seat, avoid putting heavy loads on the temporary table.
LS13156
LS10051a
the
You should use front passenger’s seatback as a temporary table only when the vehicle is stopped. To use the seatback table, fold the seat- back down. (For detailed information, see “—Folding front passenger’s seat” on page 39 in Section 1- 3.)
CAUTION
To avoid serious injury: (cid:1) Do not set up the seatback table
while the vehicle is moving.
(cid:1) Do not sit on the seatback table.
These hooks are designed to hang the factory- supplied cargo net. To hang the cargo net, use the cargo net hooks.
NOTICE
To prevent damage to the hook, avoid hanging items other than the cargo net on it.
2006 TACOMA from Jan.’06 Prod. (OM35871U)
261
06 04.25
Grocery bag hooks
Deck hooks
Deck rails—
LS10029
LS10042b
LS10041a
Deck rails
The hooks are designed to hang things like grocery bags.
NOTICE
To prevent damage to the hook, avoid hanging heavy loads on it.
To secure your luggage, use the deck
hooks.
See “—Stowage precautions” on page 294
in Section 2 for precautions when loading
luggage.
CAUTION
To avoid personal injury, keep the deck hooks folded when not in use.
To use the deck rails, you must install
genuine Toyota accessories or
their
equivalent for the deck rails.
Follow the manufacturer’s instructions and
precautions when
installing a genuine
Toyota accessory or equivalent.
See “—Stowage precautions” on page 294
in Section 2 for precautions when loading
luggage.
262
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
CAUTION
When you secure cargo with the deck rails, be sure follow the instructions below in order to avoid the cargo coming loose: (cid:1) Do not install accessories (tie- down cleats, storage boxes, etc.) at more than the following number of loca- tions per deck rail: Side rail:
Short deck—Max. 3 locations Long deck—Max. 4 locations
Headboard rail: Max. 3 locations
(cid:1) Spread out tie- down/support
loca- tions evenly along the length of the rails.
(cid:1) Do not exceed a total tensile load
of 200 kg (440 lb.) per deck rail.
(cid:1) To prevent luggage or cargo from sliding forward during braking, make sure the deck rail accessories such as storage box are securely attached on the deck rails.
—Tie- down cleats
LS10055a
LS10056a
12.7 mm (0.5 in.)
1: Locking plate 2: Thumb wheel 3: Tie- down cleat The deck rail system enables you to insert and move to their best location along deck rails to secure a load.
tie- down cleats
1: Deck rail 2: Detent 3: Locking plate INSTALLING THE TIE- DOWN CLEAT: 1. Loosen the thumb wheel in a coun- terclockwise motion, and depress the wheel so locking plate maintains 12.7 mm (0.5 in.) gap.
2006 TACOMA from Jan.’06 Prod. (OM35871U)
263
06 04.25
LS10057a
LS10058
LS10059a
2. Insert the locking plate into the deck rail, rotate the tie- down cleat 90(cid:2), and release the thumb wheel.
3. Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a det- ent.
4. Tighten the thumb wheel in a clock- wise motion until the clutch mecha- nism ratchets.
264
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
LS10060a
5. Check the tie- down cleat to confirm that it is locked into a detent and securely mounted to the deck rail system.
CAUTION
(cid:1) Properly install and tighten the tie- down cleats into the deck rail sys- tem. Failure to properly install and tighten tie- down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehicle is in motion.
the
(cid:1) Properly secure all cargo to prevent shifting or sliding during driving. Failure to properly secure cargo can cause injury when the vehicle is in motion.
(cid:1) Applying loads at an angle to the tie- down cleat greater than 45(cid:2) or loads greater than 100 kg (220 lb.) may cause damage the deck, deck rail system, tie- down cleat and/or the cargo.
to
(cid:1) Do not exceed a total tensile load
of 200 kg (440 lb.) per deck rail.
(cid:1) Do not install more than the follow- ing number of tie- down cleats per deck rail: Side rail:
Short deck—Max. 3 locations Long deck—Max. 4 locations
Headboard rail: Max. 3 locations
Floor mat
LS10032
Use a floor mat of the correct size. If the floor carpet and floor mat have two holes, then it is designed for use with two locking clips. Fix the floor mat with lock- ing clips into the holes in the floor carpet.
2006 TACOMA from Jan.’06 Prod. (OM35871U)
265
06 04.25
LS10033
CAUTION
Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.
interferes with
266
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 01.06
SECTION 1- 2
OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Engine immobilizer system Wireless remote control Side doors Access doors Power windows Rear window Tailgate Hood Fuel tank cap
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
15
16
20
23
24
27
27
29
30
2006 TACOMA from Jan.’06 Prod. (OM35865U)
11
06 01.06
Keys (without engine immobilizer system)
Keys (with engine immobilizer system)
LS12001
LS12002
LS12039
These keys work in every lock. Since the doors can be locked without a key, you should always carry a spare key in case you accidentally lock your key inside the vehicle.
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
Your vehicle is supplied with the two kinds of keys. 1. Master keys (black)—These keys work in every lock. Your Toyota dealer will need one of them to make a new key with a built- in transponder chip.
2. Sub key (gray)—This key works in ev-
ery lock.
A transponder chip for engine immobilizer system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.
12
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
Since the side doors can be locked with- out a key, you should always carry a spare key in case you accidentally lock your keys inside the vehicle.
LS12040
LS12041
NOTICE
When using a key containing a trans- ponder chip, observe the following precautions: (cid:1) When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
(cid:1) When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after remov- ing other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
13
06 01.06
LS12042
(cid:1) Do not bend the key grip.
(cid:1) Do not cover the key grip with any material that cuts off electromagnet- ic waves.
(cid:1) Do not knock the key hard against
other objects.
(cid:1) Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight.
(cid:1) Do not put the key in water or
wash it in an ultrasonic washer.
(cid:1) Do not use the key with electromag-
netic materials.
LS12043
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
14
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
Engine immobilizer system
LS12044
LS12003a
immobilizer system
The engine is a theft prevention system. When you in- sert the key in the ignition switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle.
in
indicator
light will start
The system is automatically set when the key is removed from the ignition switch. The flashing to show the system is set. If any of the following indicator conditions occurs, contact your Toyota dealer. (cid:1) The indicator light stays on. (cid:1) The indicator light does not start flash- ing when the key is removed from the ignition switch.
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off. For your Toyota dealer to make you a new key with built- in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you. If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.
NOTICE
Do not modify, remove or disas- semble the engine immobilizer sys- tem. If any unauthorized changes or modifications are made, proper opera- tion of the system cannot be guaran- teed.
(cid:1) The indicator light flashes inconsistent-
ly.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
15
06 01.06
For vehicles sold in U.S.A.
For vehicles sold in Canada
Wireless remote control—
This device complies with RSS- 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.
interference,
including
FCCID:MOZRI- 21BTY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
CAUTION
Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
LS12010a
1. LOCK switch 2. UNLOCK switch 3. Alarm switch The wireless remote control system is designed to lock or unlock all doors or activate the alarm from a distance with- in approximately 1 m (3 ft.) of the ve- hicle. When you operate any switch, push slowly and securely.
it
16
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage to the transmitter. (cid:1) Do not leave the transmitter in places the temperature becomes high
where such as on the dashboard.
(cid:1) Do not disassemble it. (cid:1) Avoid knocking
it hard against other
objects or dropping it.
for
transmitters
(cid:1) Avoid putting it in water. You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information. If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: (cid:1) Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
(cid:1) The battery may be depleted. Check transmitter. To the battery, see “—Replacing
the battery replace battery” on page 19.
the
in
the possibility of
If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 338 in Section 4.)
MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ43VT29R IC (Canada) IDs: Transmitter: 1470A- 1T Receiver: 1470A- 1R MADE IN U.S.A. This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
—Locking and unlocking doors
LS12011b
Locking operation
LS12012b
Unlocking operation
2006 TACOMA from Jan.’06 Prod. (OM35865U)
17
06 01.06
To lock and unlock all doors, push the switches of the transmitter slowly and securely.
To lock: Push the “ ” (lock) switch. All the doors are locked simultaneously. At this time, the turn signal lights flash once. Check to see that the doors are securely locked. If any door is not securely closed, or if the key is in the ignition switch, locking cannot be performed by the “ ” switch.
To unlock: Push the “ ” switch once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. At this time, the turn signal lights will flash twice.
When unlocking a door when all the doors are locked, the interior light comes on. The lights remain on for about 15 seconds unless either door is opened and closed. (For further information, see “Interior light” on page 143 in Section 1- 5.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will be automatically locked again. ” switch is kept pushed If the “ in, the locking or unlocking operation is not repeated. Release the switch and then push again.
” or “
—Activating alarm
LS12015a
Pushing the “ ” (alarm) switch blows the horn intermittently and flashes the headlights, tail lights, turn signal lights, and interior light. The “ ” switch is used to deter vehicle theft when you witness anyone attempting to break into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, push the “ ” switch once again, lock or unlock a door with transmit- ter, or the “LOCK” to “ON” position. The alarm does not work when the ignition key is in the “ON” position.
ignition key
from
turn
the
18
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
—Replacing battery For replacement, use a CR2032 lithium battery or equivalent.
CAUTION
Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.
NOTICE
(cid:1) When replacing the battery, be care-
ful not to lose the components.
(cid:1) Replace only with the same or equivalent type recommended by a Toyota dealer.
(cid:1) Dispose of used batteries according
to the local laws.
Replace the transmitter battery by follow- ing these procedures:
LS12017
LS12018
1. Using a coin or equivalent, open the
2. Remove the circuit board, then remove
transmitter case.
the discharged transmitter battery.
NOTICE
(cid:1) Take care not to damage the circuit
board.
(cid:1) Do not bend the terminals.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
19
06 01.06
LS12019
3. Put in a new transmitter battery with positive (+) side up. Install the circuit board into the transmitter case.
Close the transmitter case securely.
NOTICE
(cid:1) Make sure the positive side and negative side of the transmitter bat- tery are faced correctly.
(cid:1) Do not replace the battery with wet hands. Water may cause unexpected rust.
(cid:1) Do not touch or move any compo- nents inside the transmitter, or it may interfere with proper operation. (cid:1) Be careful not to bend the electrode when inserting the transmitter bat- tery and that dust or oils do not adhere to the transmitter case.
(cid:1) Close the transmitter case securely.
After replacing the battery, check that the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.
Side doors
LS12004
LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system— All lock and unlock simulta- neously with either front door. In the driv- er’s door lock, turning the key once will unlock the driver’s door and twice in suc- cession will unlock all the door simulta- neously.
the doors
20
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
Vehicles with a power door lock system—
When the interior light switch is in the
“DOOR” position, and all the doors are
unlocked using either the key or wireless
remote control transmitter, the interior light
will come on and remain on for about 15
seconds before fading out. (For further in-
formation, see “Interior light” on page 143
in Section 1- 5.)
LS12005
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position.
CAUTION
Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.
Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Vehicles with power door lock system— The door will not lock if the key is left in the ignition switch when closing the front doors.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
21
06 01.06
LS12006a
Driver’s side
LS12007a
Passenger’s side
22
lock: Push the switch down on the
LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. Operating the switch simultaneously locks or unlocks all the doors. If you do either of the following, no door can be unlocked with the power door lock switch. (cid:1) Lock all the doors with the key or wire- less remote control transmitter when all the doors are closed.
(cid:1) Open the driver’s door or front passen- ger’s door and move the inside lock knobs of both front doors to the lock position, then close the doors.
The power door lock switch can be reset in the following ways. (cid:1) Turn the ignition key to “ON”. (cid:1) Unlock all the doors with the key or
wireless remote control transmitter.
(cid:1) Unlock the driver’s door or front pas- lock the doors
senger’s door with knob, and then unlock all with the power door lock switch.
inside
the
LS12008
to
the
lock
lever
DOOR
the “LOCK”
CHILD- PROTECTORS
REAR (double cab models only) Move position as shown on the label. When the child- protector is locked, you cannot open the rear door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
CAUTION
Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle in an accident. It also helps pre- vent the doors from being opened unintentionally.
Access doors (access cab models)
LS12009a
For easy access to the rear seat, open the access door (rear door). To open: First, open the front door widely. Then pull (from the outside) or push (from the inside) the inside handle of the access door. If you try to open the front and rear doors simultaneously, they will not open. To close: First, close completely. Then close the front door. You can open and close the access door only when the front door is widely opened.
the access door
NOTICE
The front door and access door could be damaged if they hit each other when being opened or closed. Be sure to follow the above instructions.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
23
06 01.06
Power windows
LS12020
Access cab models
The windows can be operated with the switch on either front door (access cab models)/each door (double cab models). The power windows work when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened. The indicator light (“AUTO”) on the switch tells you the switch can be operated. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Pull up the switch.
front door
LS12022
Access cab models
LS12021
LS12023
Double cab models
24
Double cab models
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
Automatic operation (to open only): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.
LS12024
LS12025
Access cab models
Double cab models
2006 TACOMA from Jan.’06 Prod. (OM35865U)
25
06 01.06
Window lock switch
LS12026
Driver’s door switch (access cab models)
Window lock switch
LS12027
Driver’s door switches (double cab mod- els)
26
THE
PASSENGERS’
(double cab models) or
OPERATING WINDOW Use the switches on the passenger’s door (access cab models)/passengers’ doors the switch on the driver’s door that con- trols each passenger’s window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passenger’s (access cab models)/ passengers’ (double cab models) window cannot be operated.
CAUTION
To avoid serious personal injury, you must do the following. (cid:1) Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.
in a closing window,
the vehicle.
inside
(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.
them
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
Rear window
Tailgate
LS12028a
LS12029
(cid:1) Be sure to remove the ignition key
when you leave your vehicle.
(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.
trapped
To open the rear window, push the le- ver and slide the window. After closing the window, make sure it is completely closed.
To open the tailgate, pull the handle up.
The support cables will hold the tailgate
horizontal.
See “—Stowage precautions” on page 294
in Section 2 for precautions when loading
luggage.
After closing the tailgate, try pulling it to-
ward you
is securely
locked.
to make sure
it
NOTICE
Avoid driving with the tailgate open.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
27
06 01.06
Support cable bracket
LS12030
LS12031
LS12032
REMOVAL 1. Open the tailgate to the angle where you can release the brackets on the support cables lugs on both sides.
from
the
To release the support cable bracket, lift it up and slide it off.
2. Tilt the tailgate to about 30° from vertical and pull up the right side of the tailgate to unhook the right side.
3. Slide the tailgate a little to the right
to unhook the left side.
To attach the tailgate, follow the removal procedure in reverse order. After closing the tailgate, try pulling it to- ward you is securely closed. We closed when not in use.
recommend you keep
to make sure
tailgate
the
it
28
2006 TACOMA from Jan.’06 Prod. (OM35865U)
NOTICE
Make sure the support brackets are securely latched on both side panels when installing the tailgate.
06 01.06
Hood
LS12033
LS12034a
LS12035
To open the hood: 1. Pull the hood lock release lever. The
hood will spring up slightly.
CAUTION
Before driving, be sure that the hood is securely closed and locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.
2. Pull up
the hood.
the auxiliary catch
lever inside the engine compartment, and inserting your lift finger the opening between the hood and grille or through the grille.)
through either
(by
3. Hold the hood open by inserting the
support rod into the slot.
Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it.
the support rod
to
2006 TACOMA from Jan.’06 Prod. (OM35865U)
29
06 01.06
Fuel tank cap
CAUTION
After inserting the support rod into the slot, make sure the rod supports the hood securely to prevent injury due to unexpected, sudden hood clo- sure.
LS12036
LS12037
This indicates that the fuel filler door is on the left side of your vehicle.
1. To open the fuel filler door, pull the
door toward out as shown. When refueling, turn off the engine.
CAUTION
(cid:1) Do not smoke, cause sparks or al- flames when refueling.
low open The fumes are flammable.
(cid:1) When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.
the cap
if
30
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 01.06
(cid:1) Do not fill a fuel container in the bed under any circumstances. A static electricity charge could cause a spark and fire hazard. The proper procedure is to place an approved fuel container on the ground away from the truck for filling.
LS12038b
2. To remove the fuel tank cap, turn the cap counterclockwise by 90 de- grees (to the pressure point 1), and then turn it an additional 30 degrees (to point 2). Pause slightly before removing it.
It is not unusual to hear a slight swoosh when the cap is opened. When installing the cap, turn the cap clockwise until you hear a click. When you hear the click, the cap is fully closed. If the cap is not tightened securely, the malfunction lamp comes on. Make sure the cap is tightened securely.
indicator
The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
CAUTION
(cid:1) Make sure the cap is installed se- in
curely to prevent fuel spillage the event of an accident.
(cid:1) Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.
NOTICE
To prevent damage to the cap, apply force only in the turning direction to the cap. Do not pull or pry it.
2006 TACOMA from Jan.’06 Prod. (OM35865U)
31
06 01.06
32
2006 TACOMA from Jan.’06 Prod. (OM35865U)
06 04.25
SECTION 1- 3
OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats Front seats Flip- over jump seats Folding rear seats Head restraints Seat belts SRS driver airbag and front passenger airbag Passenger airbag off switch SRS side airbags and curtain shield airbags Front passenger occupant classification system Child restraint
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
34
40
40
42
43
55
71
72
80
90
2006 TACOMA from Jan.’06 Prod. (OM35871U)
33
06 04.25
Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.
CAUTION
(cid:1) Do not drive the vehicle unless the occupants are properly seated. Do not allow any passengers to sit on top of a folded- down seatback, or in the luggage compartment or car- go area. Persons not properly seated and/or not properly re- strained by seat belts can be se- verely injured in the event of emer- gency braking or a collision.
(cid:1) During driving, do not allow any passengers to stand up or move around between seats. Otherwise, severe the event of emergency braking or a collision.
injuries can occur
in
Front seats— —Front seat precautions Driver seat
CAUTION
The SRS driver airbag deploys with
considerable
force, and can cause
death or serious injury especially if
the driver is very close to the airbag.
The National Highway Traffic Safety
Administration (“NHTSA”) advises:
Since the risk zone for driver airbag
is the first 50—75 mm (2—3 in.) of
inflation, placing yourself 250 mm (10
in.) from your driver airbag provides
you with a clear margin of safety.
This distance is measured from the
center of the steering wheel to your
breastbone. If you sit less than 250
mm
in.) away now, you can
change your driving position in sever-
al ways:
(cid:1) Move your seat to the rear as far
as you can while still reaching the
pedals comfortably.
(10
(cid:1) Slightly recline
the back of
the
seat. Although vehicle designs vary,
many drivers can achieve the 250
mm (10 in.) distance, even with the
driver seat all the way forward, sim-
ply by reclining the back of the
seat somewhat. If reclining the back
of your seat makes it hard to see
the road, raise yourself by using a
firm, non- slippery cushion, or raise
the seat
if your vehicle has that
feature.
(cid:1) If your steering wheel is adjustable, tilt it downward. This points the air- bag toward your chest instead of your head and neck.
The seat should be adjusted as rec- ommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.
34
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
Front passenger seats
Front seats (with SRS side airbags)
CAUTION
CAUTION
(cid:1) The SRS
injury especially
front passenger airbag also deploys with considerable force, and can cause death or seri- ous if the front passenger is very close to the air- bag. The front passenger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright. (cid:1) Bench seat only—Do not use seat accessory, such as a cushion or seat cover, that covers the front seat, or do not modify or replace the upholstery of the front seat. Such accessories or changes may prevent the front passenger airbag system from activating correctly, disable the system or cause the front passenger airbag to inflate ac- cidentally, resulting in death or seri- ous injury.
The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. (cid:1) Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or seriously in- jured.
(cid:1) Do not use seat accessories which cover the area where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.
(cid:1) Do not modify or replace the seats or upholstery of the seats with side airbags. Such change may prevent the side airbag system from activat- ing correctly, disable the system, or cause the side airbags to inflate ac- cidentally, resulting in death or seri- ous injury.
—Seat adjustment precautions
CAUTION
(cid:1) Do not adjust the seat while the vehicle is moving as the seat may unexpectedly move and cause the driver to lose control of the vehicle. (cid:1) Be careful that the seat does not
hit a passenger or luggage.
(cid:1) After adjusting the seat position, re- lease the lever and try sliding the seat forward and backward to make sure it is locked in position.
(cid:1) After adjusting the seatback, push your body back against the seat to make sure the seat in position.
locked
is
(cid:1) Do not put objects under the seats. Otherwise, the objects may interfere with the seat- lock mechanism or unexpectedly push up the seat posi- tion adjusting lever and the seat may suddenly move, causing the driver to lose control of the vehicle.
2006 TACOMA from Jan.’06 Prod. (OM35871U)
35
06 04.25
—Adjusting front seats
(cid:1) While adjusting the seat, do not put your hands under the seat or near the moving parts. Otherwise, your hands or fingers may be caught and injured.
LS13143
LS13144a
36
2006 TACOMA from Jan.’06 Prod. (OM35871U)
Separate seats
Bench seat
06 04.25
—Moving passenger’s seat for rear seat entry (access cab models)
1. SEAT POSITION ADJUSTING LEVER
Pull the lever up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. DRIVER’S SEAT LUMBAR SUPPORT ADJUSTING KNOB (on some models) Turn the knob either way.
LS13145
3. SEATBACK
ANGLE
ADJUSTING
LEVER Lean forward and pull the lever up. Then lean back to the desired angle and release the lever.
CAUTION
(cid:1) After putting back
try pushing the seat forward and rear- ward to make sure it is secured in place.
the seat,
(cid:1) Never allow anyone to rest their foot on the press pedal while the vehicle is moving.
CAUTION
reclining
Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or personal injury.
For easy access to the rear seat: 1. Lift the seatback angle adjusting lever the seat-
the pedal behind
or press back. The seat will slide forward.
2. Move the seat to the front- most posi-
tion.
After passengers are in, lift up the seat- back and return the seat until it locks.
2006 TACOMA from Jan.’06 Prod. (OM35871U)
37
06 04.25
—Folding seatback (bench seat only)
LS13153
LS13146
BEFORE FOLDING SEATBACK Make sure the center seat belt is removed from the guide when folding seatback.
Pull the seatback lock release lever and fold down the seatback. Hold the lever until you have swung the seatback forward slightly.
CAUTION
CAUTION
When returning the seatback to the upright position, observe the follow- ing precautions in order to prevent personal injury in a collision or sud- den stop: (cid:1) Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.
(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.
The seat belt passes guide when the seat belt is in use.
through
the
38
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
—Folding front passenger’s seat (on some models)
LS13154
LS13155
LS13156
1. Pull the seatback angle adjusting le- ver and raise the seatback to its up- right position.
2. Pull the seatback folding lever and
fold the seatback down.
You should use the seatback as a tempo- rary is stopped.
table only when
the vehicle
CAUTION
To avoid serious injury: (cid:1) Do not set up the seatback table
while the vehicle is moving.
(cid:1) Do not sit on the folded seatback. (cid:1) Make sure front passenger’s seat is securely locked in sliding position when you set the seat as a temporary table.
the
2006 TACOMA from Jan.’06 Prod. (OM35871U)
39
06 04.25
NOTICE
To prevent damage to the seat, avoid putting heavy loads on the temporary table.
Flip- over jump seats (access cab models)
Folding rear seats (double cab models)
LS13147
LS13148a
To flip over the bottom cushion, pull
the lock release strap.
See “—Stowage precautions” on page 294
in Section 2 for precautions when loading
luggage.
BEFORE FOLDING REAR SEATS 1. Stow the rear seat belt buckles as
shown in the illustration.
This prevents the seat belt buckles from falling out when you fold the seatback.
CAUTION
NOTICE
When returning the bottom cushion to its original position, make sure the seat belts are not twisted or caught under the bottom cushion and are ar- ranged in their proper position and are ready to use.
To prevent damage to the seat belt buckles, the seat belt buckles must be stowed before you fold the seat- back.
40
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
LS13183
LS13150b
LS13151
2. Make sure the shoulder belt passes through the hanger when folding the rear seat.
This prevents the shoulder belt from being damaged.
CAUTION
The seat belt must be removed from the hanger when the seat belt is in use.
FOLDING REAR SEATS 1. Swing
the bottom cushion up by pulling the lock release strap, and remove the head restraint.
If desired, each bottom cushion may be raised separately.
NOTICE
To prevent damage to the box under the seat, do not sit on the box when the bottom cushion is in the raised position.
2. Attach
the head restraints
the holders located on the back sides of the bottom cushions.
to
2006 TACOMA from Jan.’06 Prod. (OM35871U)
41
06 04.25
CAUTION
When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: (cid:1) Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.
(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.
(cid:1) Make sure the bottom cushion is securely locked by trying to pull up the edge of the cushion near the lock release straps.
Head restraints
LS13157
Front (separate seats)
LS13158a
LS13152a
3. Fold down the seatback by pulling
the lock release strap.
If desired, each seatback can be folded down separately.
CAUTION
To avoid serious injury, do not sit on or place anything on the folded seat- back while the vehicle is moving.
42
Front (bench seat)
2006 TACOMA from Jan.’06 Prod. (OM35871U)
06 04.25
LS13159b
Rear (double cab models)
For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. Rear center head restraint (double cab models) and front center head restraint (bench seat)—When an occupant sits on the the center position of rear seats (double cab models) or the front seats (bench seat), always pull up the center head restraint to the lock position.
The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.
CAUTION
(cid:1) Adjust the center of the head re- straint so that it is closest to the top of your ears.
(cid:1) After adjusting the head restraint, make sure it is locked in position. the head re-
(cid:1) Do not drive with
straints removed.