Login- Download PDF Manual
-
2-2. Instrument cluster
Odometer/trip meter
Odometer
Displays the total distance the vehicle has been driven.
Trip meter
Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently. Display change button Performs odometer, trip meter and meter display customization. While the trip meter is being displayed: Pressing and holding the button will reset the trip meter. While the odometer is being displayed: Pressing and holding the button enables Eco Driving Indicator Light and the turn-by-turn navigation to be activated or deactivated.
Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Brighter Darker
219
2-2. Instrument cluster
Eco Driving Indicator Light and turn-by-turn navigation display customization
While the odometer is being displayed, customization can be per- formed by pressing and holding the display change button.
Each time the display change button is pressed, ECO Driving Indi- cator Light display is activated or deactivated. If OFF is selected, the Eco Driving Indicator Light will not be displayed. Each time the display change button is pressed, the turn-by-turn navigation is activated or deactivated. If OFF is selected, the turn-by-turn navigation display will not be dis- played.
When settings have been completed, press and hold the display change button until the odometer is displayed.
220
2
2-2. Instrument cluster
■The meters and display illuminate when
The “POWER” switch is in ON mode.
■EV System Indicator
Power area Shows that an Eco-friendly driving range is being exceeded (during full power driving etc.) Eco area Shows that the vehicle is being driven in an Eco-friendly manner. Charge area Shows that energy is being recovered via the regenerative charging. Eco Driving Indicator During Eco-friendly acceleration oper- ation (Eco driving), Eco Driving Indica- tor Light will the accelerator pedal is depressed exces- sively, and when is stopped, the light turns off.
turn on. When
the vehicle
Eco Driving Indicator Light will not oper- ate in the following conditions: ●The driving mode is set to SPORT
mode.
●The vehicle speed is approximately 80
mph (130 km/h) or higher.
Eco Driving Indicator Light can be acti- vated or deactivated. (P. 220)
●By keeping the indicator needle within Eco area, more Eco-friendly driv-
ing can be achieved.
●Charge area indicates regeneration* status. Regenerated energy will be
used to charge the traction battery.
*: When used in this manual, “regeneration” refers to the conversion of
energy created by the movement of the vehicle into electrical energy.
221
2-2. Instrument cluster
■The brightness of the instrument panel lights
When the tail lights are turned on, the meter’s brightness will be reduced slightly unless the meter brightness level adjustment is set to the brightest setting. If the tail lights are turned on when the surroundings are dark, the meter’s brightness will reduce slightly. However, when the surroundings are bright, such as during the daytime, the meter’s brightness will not be reduced even if the tail lights are turned on.
222
2-2. Instrument cluster Indicators and warning lights
The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. ■ Instrument cluster
■ Center panel
223
2-2. Instrument cluster
■ Outside left of vehicle
224
2-2. Instrument cluster
■ Indicators
The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator (P. 215) Headlight indicator (P. 234)
Cruise control indicator (P. 243) Cruise control set indi- cator (P. 243)
*1, 2
*1
(Center panel)
Headlight high beam indicator (P. 235)
Slip indicator (P. 251, 256)
VSC OFF indicator (P. 252)
Security indicator (P. 149)
“READY” indicator (P. 200)
Shift position indi- cators (P. 206)
*1
“TRAC OFF” indicator (P. 252, 477)
Plug-in indicator (P. 59)
(green)
SPORT mode indicator (P. 208)
*1
Eco Driving Indicator Light (P. 221)
*1
“AIR BAG ON” and “AIR BAG OFF” indica- tor (P. 166)
Charging indi- cator (P. 59)
(Center panel)
(Outside left of the vehicle)
*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the EV system is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
*2: The light flashes to indicate that the system is operating.
225
2-2. Instrument cluster
■ Warning lights
Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (P. 417)
*1
*2
*1
*3
*1
*4
*1
*1
*1
*1
*1
(yellow)
(Center panel)
*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the EV system is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
*2: The light flashes to indicate a malfunction. *3: Driver’s/front passenger’s seat belt reminder light *4: Both lights flash quickly for 10 seconds to indicate that the system is
malfunctioning.
CAUTION
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS airbag warning light not come on when you start the EV system, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.
226
2
2-2. Instrument cluster Multi-information display
The multi-information display presents the driver with a variety of driving-related data.
● Trip information (P. 229) Displays driving range, power consumption and other cruis- ing-related information.
● Warning messages
(P. 427) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.
227
2-2. Instrument cluster
■ Display contents
Each time the “DISP” switch is pressed, the menu screen changes. When the desired menu screen is displayed, stop pressing the “DISP” switch. The details screen will soon be displayed.
Trip information contents
Switching display items
Driving range Turn-by-turn navigation* Efficiency Trip efficiency ECO coach CO2 reduction Aux power
Press the “DISP” switch.
*: Not shown when no destination is set or when the turn-by-turn naviga-
tion display is not activated. (P. 220, 231).
228
2
2-2. Instrument cluster
Trip information
■ Driving range
Displays an estimated driving range according to the amount of charge remaining in the traction battery and air conditioning settings.
Displays what the estimated maximum driving range is with the air conditioning system off according to the amount of charge remaining in the traction battery. Displays the amount the estimated maximum driv- ing range is shortened according to current air con- ditioning mode. The climate setting is linked to the air conditioning sys- tem, and changes according to air conditioning settings. (P. 276) The estimated maximum driving range is only an esti- mate. According to driving conditions, the actual driving range may differ. Keep early charging in mind. The driving range according to current air conditioning mode is displayed in the left section of the instrument cluster. (P. 218)
229
2-2. Instrument cluster
■ Efficiency
Displays average power consumption and current power consumption.
Average power consumption Displays the average power consumption since the function was reset.
The function can be reset by pressing the “DISP” but- ton for longer than 1 second when the average power consumption/current power consumption is dis- played.
Current power consumption Displays current power consumption.
■ Trip efficiency
Displays the average power consumption in intervals of 5 minutes. Current power consumption is simulta- neously displayed, allowing it to be compared with previous power consumption rates.
■ ECO coach
Evaluates the level of eco friendly driving according to acceleration, speed and braking. An overall score is also displayed.
Displays the average score up until now when the EV system is turned off. (P. 232)
230
2-2. Instrument cluster
■ CO2 reduction
In accordance with the amount of charging performed since the function was last reset, the amount of CO2
reduction when compared to a conventional gasoline vehicle is displayed as a growing tree.The function can be reset by pressing the “DISP” button for longer than 1 second when the CO2 reduction screen is displayed.
■ AUX Power
Displays average 12-volt battery power consumption and current 12-volt battery power consumption.
Average 12-volt battery consumption Displays the average 12-volt battery power con- sumption since the function was reset.
The function can be reset by pressing the “DISP” but- ton for longer than 1 second when the Aux Power screen is displayed.
Current 12-volt battery power consumption Displays the current 12-volt battery power con- sumption.
Turn-by-turn navigation*
Displays a notification of upcom- ing intersections during naviga- tion system route guidance
Turn-by-turn can be activated or deactivated. (P. 220)
*: For more details on route guid- ance settings, refer to “Navigation System Owner’s Manual”.
231
2-2. Instrument cluster
Ending screen
When the EV system is turned off, drive information data since the system was started is dis- played after the ending anima- tion.
When the driver’s door is closed, the screen turns off.
■ECO coach
●As the accelerator pedal is not depressed, the driven distance using
cruise control is not included in the ECO coach.
●As the eco coach evaluation differs according to driving conditions and environmental factors, in some cases it may not be linked to power con- sumption.
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display.
■Customization that can be configured at Toyota dealer
Setting of available languages can be changed. (Customizable features P. 500)
CAUTION
■ECO score
ECO score should be used as a guide only. Always drive safely in accor- dance with road and traffic conditions.
232
2-2. Instrument cluster
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.
233
2-3. Operating the lights and wipers Headlight switch
The headlights can be operated manually or automatically.
headlights, The lights and parking daytime running lights turn on and off automatically. (When the “POWER” switch is in ON mode) The side marker, parking, tail, license plate, daytime run- and ning instrument panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on. The daytime ning lights turn off.
lights
run-
234
2
2-3. Operating the lights and wipers
Turning on the high beam headlights
With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.
Manual headlight leveling dial
The level of the headlights can be adjusted according to the number of passengers and the loading condition of the vehicle.
Raises the level of the head- lights Lowers the level of the head- lights
235
2-3. Operating the lights and wipers
■ Guide to dial settings
Occupancy and luggage load conditions Luggage load Occupants
Dial position
Driver
Driver and front pas-
senger
All seats occupied All seats occupied
Driver
None
None
None
Full luggage loading Full luggage loading
■Daytime running light system
●To make your vehicle more visible to other drivers, the daytime running lights turn on automatically whenever the EV system is started and the parking brake is released. Daytime running lights are not designed for use at night.
●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve power consumption.
■Headlight control sensor
The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.
interferes with
236
2
2-3. Operating the lights and wipers
■Automatic light off system
The headlights and tail lights turn off 30 seconds after driver’s door is opened and closed if the “POWER” switch has been turned to ACCESSORY mode or turned off. (The lights turn off immediately if on the key is pressed twice after all the doors are closed.) To turn the lights on again, turn the “POWER” switch to ON mode, or turn the headlight switch off and then back to
or
■Customization that can be configured at Toyota dealer Settings (e.g. light sensor sensitivity) can be deactivated. (Customizable features P. 500)
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than necessary when the EV system is off.
237
2-3. Operating the lights and wipers Windshield wipers and washer
When “INT” is selected, the wiper interval can be adjusted for inter- mittent operation. The wiper operation is selected by moving the lever as follows.
wind- Intermittent shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
238
2-3. Operating the lights and wipers
Wash/wipe operation
The wipers will automatically operate a couple of times after the washer squirts.
■The windshield wipers and washer can be operated when
The “POWER” switch is in ON mode.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.
CAUTION
■Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes warm. The fluid may freeze on the windshield and cause low visibility. This may lead to an accident, resulting in death or serious injury.
239
2-3. Operating the lights and wipers
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over- heat.
■When a nozzle becomes blocked
In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
240
2
2-3. Operating the lights and wipers Rear window wiper and washer
The wiper operation is selected by moving the lever as follows:
window
Intermittent window wiper operation Normal wiper operation Washer/wiper dual operation Washer/wiper dual operation
■The rear window wiper and washer can be operated when
The “POWER” switch is in ON mode.
■If no washer fluid sprays
Check that the washer nozzle is not blocked if there is washer fluid in the washer fluid reservoir.
241
2-3. Operating the lights and wipers
NOTICE
■When the rear window is dry
Do not use the wipers, as they may damage the rear window.
■When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over- heat.
■When a nozzle is blocked
Do not try to clear it with a pin or other object. The nozzle will be damaged.
242
2-4. Using other driving systems Cruise control
Use the cruise control to maintain a set speed without depressing the accelerator pedal.
Indicators Cruise control switch
■ Setting the vehicle speed
STEP 1
Press the “ON-OFF” button to activate the cruise control.
indicator will
Cruise control come on. Press the button again deactivate the cruise control.
to
STEP 2
Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
“SET” indicator will come on. The vehicle speed at the moment the lever is released becomes the set speed.
243
2-4. Using other driving systems
■ Adjusting the set speed
To change the set speed, operate the lever until the desired set speed is obtained.
Increase the speed Decrease the speed Hold the lever until the desired speed setting is obtained. Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.
the
The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.
■ Canceling and resuming the constant speed control
Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40 km/h).
lever up constant
the the
244
2-4. Using other driving systems
■Cruise control can be set when
●The shift position is in D. ●Vehicle speed is above approximately 25 mph (40 km/h) and below the
maximum vehicle speed. Maximum vehicle speed differs according to driving mode. (P. 208)
■Accelerating after setting the vehicle speed
●The vehicle can be accelerated normally. After acceleration, the set
speed resumes.
●Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.
■Automatic cruise control cancelation
Cruise control will stop maintaining the vehicle speed in any of the following situations. ●Actual vehicle speed falls more than approximately 10 mph (16 km/h)
below the preset vehicle speed. At this time, the memorized set speed is not retained.
●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated.
■If the cruise control indicator light flashes and “Check Cruise Control
System” is shown on the multi-information display There may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
245
2-4. Using other driving systems
CAUTION
■To avoid operating the cruise control by mistake
Switch the cruise control off using the “ON-OFF” button when not in use.
■Situations unsuitable for cruise control
Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills
Vehicle speed may exceed the set speed when driving down a steep hill.
246
2
2-4. Using other driving systems Rear view monitor system
The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.
The rear view image is dis- played when the shift position is in R.
If the shift position is changed out of R, the screen returns to the previous one.
247
2-4. Using other driving systems
■Displayed area
Corners of bumper
The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.
248
2
2-4. Using other driving systems
■Rear view monitor system camera
In the following cases, it may become difficult to see the images on the screen, even when the system is func- tioning correctly: ●The vehicle is in a dark area, such
as at night.
●The temperature near the lens is
extremely high or low.
●Water droplets are on the camera lens or humidity is high, such as when it rains.
●Foreign matter, such as snow or
mud, adheres to the camera lens.
●The camera has scratches or dirt on
it.
●The sun or headlights are shining
directly into the camera lens.
■Smear effect
If a bright light, such as sunlight reflected off the vehicle body, is picked up by the camera, a smear effect* char- acteristic to the camera may occur. *: Smear effect A phenomenon that occurs when a bright light is picked up by the camera; when transmitted by light source appears to have a vertical streak above and below it.
the camera,
the
249
2-4. Using other driving systems
CAUTION
■When using the rear view monitor system, observe the following pre- cautions to avoid an accident that could result in death or serious inju- ries: ●Never depend solely on the monitor system when reversing. ●Always check visually and with the mirrors to confirm your intended path is
clear.
●Depicted distances between objects and flat surfaces differ from actual
distances.
●Do not use the system if the back door is open.
■Conditions which may affect the rear view monitor system
●If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer.
●Rapid temperature changes, such as when hot water is poured on the
vehicle in cold weather, may cause the system to function abnormally.
●If the camera lens is dirty, it cannot transmit a clear image. Rinse with water and wipe with a soft cloth. If extremely dirty, wash with a mild cleanser and rinse.
●The displayed image may be darker and moving images may be slightly
distorted when the system is cold.
●As the camera has a water proof construction, do not detach, disassemble
or modify it. This may cause incorrect operation.
●Do not allow organic solvent, car wax, window cleaner or glass coat to
adhere to the camera. If this happens, wipe it off as soon as possible.
●If the temperature changes rapidly, such as when hot water is poured on
the vehicle in cold weather, the system may not operate normally.
●When the camera is used under fluorescent lights, sodium lights, or mer-
cury lights, the lights and the illuminated areas may appear to flicker.
●When washing the vehicle, do not apply intensive bursts of water to the camera or camera area. Doing so may result in the camera malfunction- ing.
250
2
2-4. Using other driving systems Driving assist systems
To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface
■ Brake assist
Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation
■ VSC (Vehicle Stability Control)
Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces
■ TRAC (Traction Control)
Helps to maintain drive power and prevent the drive wheels from spin- ning when starting the vehicle or accelerating on slippery roads
■ Hill-start assist control
P. 256
■ EPS (Electric Power Steering)
Employs an electric motor to reduce the amount of effort needed to turn the steering wheel
When the TRAC/VSC/ABS systems are operating
The slip indicator light will flash while the TRAC/VSC/ABS sys- tems are operating.
251
2-4. Using other driving systems
Disabling the TRAC system
If the vehicle gets stuck in mud, dirt or snow, the TRAC system may reduce power from the EV system to the wheels. Pressing to turn the system off may make it easier for you to rock the vehicle in order to free it.
To turn the TRAC system off, quickly press and release
The “TRAC OFF” indicator light will come on. Press tem back on.
again to turn the sys-
■Turning off both TRAC and VSC systems
To turn the TRAC and VSC systems off, press and hold seconds while the vehicle is stopped. The “TRAC OFF” indicator light and VSC OFF indicator light will come on. Press
again to turn the systems back on.
for more than 3
■When the “TRAC OFF” indicator light comes on even if the VSC OFF
switch has not been pressed TRAC cannot be operated. Contact your Toyota dealer.
252
2
2-4. Using other driving systems
■Sounds and vibrations caused by the ABS, brake assist, TRAC, and
VSC systems ●A sound may be heard from the motor compartment when the EV system is started or just after the vehicle begins to move, if the brake pedal is depressed forcefully or repeatedly, or 1 - 2 minutes after the EV system is stopped. This sound does not indicate that a malfunction has occurred in any of these systems.
●Any of the following conditions may occur when the above systems are
operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.
■EPS operation sound
When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Automatic reactivation of TRAC and VSC systems
After turning the TRAC and VSC systems off, the systems will be automati- cally re-enabled in the following situations: ●When the “POWER” switch is turned off ●If only the TRAC system is turned off, the TRAC will turn on when vehicle
speed increases If both the TRAC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.
■Reduced effectiveness of the EPS system
The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the EV sys- tem off. The EPS system should return to normal within 10 minutes.
■If the slip indicator comes on...
It may indicate a malfunction in the TRAC, VSC and ABS. Contact your Toyota dealer.
253
2-4. Using other driving systems
CAUTION
■The ABS does not operate effectively when
●The limits of tire gripping performance have been exceeded (such as
excessively worn tires on a snow covered road).
●The vehicle hydroplanes while driving at high speed on wet or slick roads. ■Stopping distance when the ABS is operating may exceed that of nor-
mal conditions The ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you, especially in the fol- lowing situations: ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or uneven surfaces
■TRAC may not operate effectively when
Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Drive the vehicle carefully in conditions where stability and power may be lost.
■When the VSC is activated
The slip indicator light flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes.
■When the TRAC/VSC systems are turned off
Be especially careful and drive at a speed appropriate to the road condi- tions. As these are the systems to ensure vehicle stability and driving force, do not turn the TRAC/VSC systems off unless necessary.
254
2-4. Using other driving systems
CAUTION
■Replacing tires
Make sure that all tires are of the specified size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recommended tire inflation pressure level. The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.
■Handling of tires and the suspension
Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.
255
2-4. Using other driving systems Hill-start assist control
Assists with starting off and temporarily maintains braking power even if the foot is removed from the brake pedal when starting off on an incline or a slippery slope.
To engage hill-start assist con- trol, further depress the brake pedal when is stopped completely.
the vehicle
A buzzer will sound once to indicate the system is acti- vated. The slip indicator will also start flashing.
■Hill-start assist control operating conditions
●The system operates in the following situations: • The shift position is in a position other than P. • The parking brake is not applied. • The accelerator pedal is not depressed.
●Hill-start assist control cannot be operated while the slip indicator light is
illuminated.
■Hill-start assist control
●While hill-start assist control is operating, the brakes remain automati- cally applied after the driver releases the brake pedal. The stop lights and the high mounted stoplight turn on.
●Hill-start assist control operates for about 2 seconds after the brake pedal
is released.
●If the slip indicator does not flash and the buzzer does not sound when the brake pedal is further depressed, slightly reduce the pressure on the brake pedal (do not allow the vehicle to roll backward) and then firmly depress it again. If the system still does not operate, check that the oper- ating conditions explained above have been met.
256
2
2-4. Using other driving systems
■Hill-start assist control buzzer
●When hill-start assist control is activated, the buzzer will sound once. ●In the following situations, hill-start assist control will be canceled and the
buzzer will sound twice. • No attempt is made to drive the vehicle within approximately 2 seconds
of releasing the brake pedal.
• The P position switch is pushed. • The parking brake is applied. • The brake pedal is depressed again. • The brake pedal has been depressed for more than approximately 3
minutes.
■If the slip indicator comes on
It may indicate a malfunction in the system. Contact your Toyota dealer.
CAUTION
■Hill-start assist control
●Do not overly rely on hill-start assist control. Hill-start assist control may
not operate effectively on steep inclines and roads covered with ice.
●Unlike the parking brake, hill-start assist control is not intended to hold the vehicle stationary for an extended period of time. Do not attempt to use hill-start assist control to hold the vehicle on an incline, as doing so may lead to an accident.
257
2-5. Driving information Utility vehicle precautions
This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity as compared to ordinary passenger cars.
Utility vehicle feature
● Specific design characteristics give it a higher center of gravity than ordinary passenger cars. This vehicle design feature causes this type of vehicle to be more likely to rollover. And, utility vehicles have a significantly higher rollover rate than other types of vehi- cles.
● This vehicle is not designed for cornering at the same speeds as ordinary passenger cars. Therefore, sharp turns at excessive speeds may cause rollover.
● This vehicle is an electric vehicle. It has a heavy traction battery mounted under the floor, giving the vehicle a lower ground clear- ance than that of conventional off-road vehicles. Avoid off-road driving as it may damage the traction batteries.
258
2
2-5. Driving information
CAUTION
■Utility vehicle precautions
Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ●In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.
●Avoid sharp turns or abrupt maneuvers, if at all possible. Failure to operate this vehicle correctly may result in loss of control or vehicle rollover caus- ing death or serious injury.
●Avoid loading any items on the roof that will raise the vehicle’s center of
gravity.
●Always slow down in gusty crosswinds. Because of its profile and taller vehicle height, this vehicle is more sensitive to side winds than an ordinary passenger car. Slowing down will allow you to have better control.
●This vehicle is an electric vehicle. Avoid driving through deep water that may cause the battery pack, motor or motor controller to be submerged or flooded. Furthermore, this vehicle is not suitable for off-road driving, unlike conventional sport utility vehicles. When it is unavoidable to drive off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension, chassis and traction batteries.
●Do not drive horizontally across steep slopes. Driving straight up or straight down is preferred. Your vehicle (or any similar vehicle) can tip over sideways much more easily than forward or backward.
259
2-5. Driving information
Off-road driving
Your vehicle is not designed to be driven off-road. However, in the event that off-road driving cannot be avoided, please observe the fol- lowing precautions to help avoid the areas prohibited to vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit-
ted to travel.
● Respect private property. Get owner’s permission before entering
private property.
● Do not enter areas that are closed. Honor gates, barriers and signs
that restrict travel.
● Stay on established roads. When conditions are wet, driving tech- niques should be changed or travel delayed to prevent damage to roads.
● Avoid driving on very steep, slippery roads and other surfaces,
such as sand, where the tires are liable to lose traction.
260
2-5. Driving information
CAUTION
■Off-road driving precautions
Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ●Drive carefully when off-road driving is unavoidable. Do not take unneces-
sary risks by driving in dangerous places.
●Do not grip the steering wheel spokes when off-road driving is unavoid- able. A bad bump could jerk the wheel and injure your hands. Keep both hands and especially your thumbs on the outside of the rim.
●Always check your brakes for effectiveness immediately after driving in
sand, mud, water or snow.
●When it is unavoidable to drive through tall grass, mud, rock, sand, etc., take care not to damage the traction batteries equipped under the floor. After driving through such terrain, check that there is no grass, bush, paper, rags, stone, sand, etc. adhering or trapped on the underbody. Clear off any such matter from the underbody. If the vehicle is used with these materials trapped or adhering to the underbody, a breakdown or fire could occur.
●When driving off-road is unavoidable, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension, chassis, drive unit or the traction batteries.
261
2-5. Driving information
NOTICE
■To prevent water damage
Take all necessary safety measures to ensure that water damage to the trac- tion battery and motor or other components does not occur. ●Water entering the motor will cause severe motor damage. ●Water entering the traction battery may cause short-circuit. ●Water can wash the grease from wheel bearings, causing rusting and pre- mature failure, and may also enter the differential and transmission case, reducing the gear oil’s lubricating qualities.
■When you drive through water
When driving through water is unavoidable, drive slowly, taking extreme cau- tion to avoid deep water.
262
2-5. Driving information Cargo and luggage
Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever
possible.
● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage
evenly within the luggage compartment.
● For better power economy, do not carry unnecessary weight.
Capacity and distribution
Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle's placard.
(2)Determine the combined weight of the driver and passengers that
will be riding in your vehicle.
(3)Subtract the combined weight of the driver and passengers from
XXX kg or XXX lbs.
(4)The resulting figure equals the available amount of cargo and lug-
gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 - 750 (5 150) = 650 lbs.)
(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the avail- able cargo and luggage load capacity calculated in Step 4.
263
2-5. Driving information
(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (P. 267) Toyota does not recommend towing a trailer with your vehicle. Your vehi- cle is not designed for trailer towing.
Calculation formula for your vehicle
Cargo capacity Total load capacity (vehicle capacity weight) (P. 482)
When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb. (kg), the available amount of cargo and luggage load capacity will be C lb. (kg) as follows: B*2 lb. (kg) - A*1 lb. (kg) = C*3 lb. (kg) *1: A = Weight of people *2: B = Total load capacity *3: C = Available cargo and luggage load
In this condition, if 3 more passengers with the combined weight of D lb. (kg) get on, the available cargo and luggage load will be reduced E lb. (kg) as follows:
C lb. (kg) - D*4 lb. (kg) = E*5 lb. (kg) *4: D =Additional weight of people *5: E =Available cargo and luggage load
264
2-5. Driving information
As shown in the example above, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.
CAUTION
■Things that must not be carried in the luggage compartment
The following things may cause a fire if loaded in the luggage compart- ment. ●Receptacles containing gasoline ●Aerosol cans
■Storage precautions
Observe the following precautions. Failure to do so may result in death or serious injury. ●Stow cargo and luggage in the luggage compartment whenever possi-
ble.
●Do not stack anything in the luggage compartment higher than the
seatbacks. Such items may be thrown about and possibly injure people in the vehicle in the event of sudden braking or in an accident.
●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident: • At the feet of the driver • On the front passenger or rear seats (when stacking items) • On the instrument panel • On the dashboard
265
2-5. Driving information
CAUTION
●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.
●When you fold down the rear seats, long items should not be place
directly behind the front seats.
●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or an accident. ■Capacity and distribution
●Do not exceed the maximum axle weight rating or the total vehicle
weight rating.
●Even if the total load of occupant's weight and the cargo load is less
than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.
266
2-5. Driving information Vehicle load limits
Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity (vehicle capacity weight): (P. 482)
Total load capacity means the combined weight of occupants, cargo and luggage.
■ Seating capacity: 5 occupants (Front 2, Rear 3)
Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.
■ Towing capacity
Toyota does not recommend towing a trailer with your vehicle.
■ Cargo capacity
Cargo capacity may increase or decrease depending on the weight and the number of occupants.
■Total load capacity and seating capacity
These details are also described on the tire and loading information label. (P. 374)
CAUTION
■Overloading the vehicle
Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
267
2-5. Driving information Winter driving tips
Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations
● Use fluids that are appropriate to the prevailing outside tem-
peratures. • Motor coolant • Heater coolant • Traction battery coolant • Washer fluid
● Have a service technician inspect the condition of the 12-volt
battery.
● Have the vehicle fitted with four snow tires or purchase a set
of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle
Perform the following according to the driving conditions: ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● Do not try to forcibly open the charging port cap if it is frozen. Melt the ice using a hair dryer, immediately and thoroughly wiping away any moisture.
● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.
● Check for and remove any excess ice or snow that may have accumulated on the exterior lights, vehicle's roof, chassis, around the tires or on the brakes.
268
2-5. Driving information
● Remove any snow or mud from the bottom of your shoes
before getting in the vehicle.
■ When driving the vehicle
Accelerate the vehicle slowly, keep a safe distance between you and the vehicle ahead, and drive at a reduced speed suitable to road conditions.
■ When parking the vehicle
Park the vehicle and push the P position switch without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.
Selecting tire chains
Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.
Side chain
0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length
Cross chain
0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length
269
2-5. Driving information
Regulations on the use of tire chains
● Regulations regarding the use of tire chains vary depending on location and type of road. Always check local regulations before installing chains.
● Install the chains on the front tires.
■Tire chain installation
Observe the following precautions when installing and removing chains: ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on
the rear tires.
●Install tire chains on front tires as tightly as possible. Retighten chains
after driving 1/4 1/2 mile (0.5 1.0 km).
●Install tire chains following the instructions provided with the tire
chains.
270
2-5. Driving information
CAUTION
■Driving with snow tires
Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of
snow tires being used.
●Use snow tires on all, not just some wheels. ●Do not mix tires of different makes, models, tread patterns or tread-
wear.
■Driving with tire chains
Observe the following precautions to reduce the risk of accidents. Failure to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains
being used, or 30 mph (50 km/h), whichever is lower.
●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden acceleration, abrupt steering, sudden braking and shift-
ing operations that cause sudden regenerative braking.
●Slow down sufficiently before entering a curve to ensure that vehicle
control is maintained.
271
2-5. Driving information
NOTICE
■Repairing or replacing snow tires
Request repairs or replacement of snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the operation of the tire pressure warning valves and transmitters.
■Fitting tire chains
The tire pressure warning valves and transmitters may not function cor- rectly when tire chains are fitted.
272
2-5. Driving information Trailer towing
Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your vehicle is not designed for trailer towing or for the use of tow hitch mounted carriers.
273
2-5. Driving information Dinghy towing
Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.
NOTICE
■To avoid serious damage to your vehicle
Do not tow your vehicle with the four wheels on the ground.
274
2-5. Driving information
275
Interior features
3-4. Other interior features
Sun visors ........................ 304
Vanity mirrors................... 305
Power outlets ................... 306
Seat heaters..................... 310
Armrest ............................ 313
Coat hooks....................... 314
Assist grips....................... 315
Floor mat.......................... 316
Luggage compartment features.......................... 317
Garage door opener......... 320
Safety Connect ................ 3263-1. Using the air conditioning
system and defogger Automatic air conditioning system ....... 276
Rear window and outside rear view mirror defoggers....................... 2923-2. Using the interior lights
Interior lights list............... 293
• Personal/interior light main switch .................... 294
• Personal/interior lights .............................. 294
• Interior light .................... 295
• Luggage compartment light ................................ 2953-3. Using the storage features
List of storage features .... 296
• Glove box....................... 297
• Console box................... 298
• Cup holders ................... 299
• Bottle holders................. 300
• Auxiliary boxes............... 302275
3-1. Using the air conditioning system and defogger Automatic air conditioning system
The driving distance of the RAV4 EV is affected by the method of air conditioning use. In order to extend driving range, Toyota recom- mends using AUTO ECO mode and setting temperatures conserva- tively. The effect on driving range can be confirmed on the meter. (P. 218) ■ Operation mode
Mode
ECO setting
Details
Air conditioning is operated automati- cally, maintaining an optimal balance between cabin comfort and driving range. The seat heater is also linked and controlled depending on condi- tions. Air conditioning is operated automati- cally. More importance is placed on extending driving range than in ECO LO mode and the air conditioning is used moderately. The seat heater is also linked and controlled depending on conditions. Air conditioning is operated automati- cally with more importance placed on cabin comfort than ECO LO mode. Therefore, driving range is shorter than when using ECO LO mode. Fan speed adjustment or changing air outlets is performed manually. Functions that have not been set in Manual mode will continue to operate in AUTO ECO mode. The seat heater is also linked and controlled depend- ing on conditions. Fan speed adjustment or changing air outlets is performed manually.
ECO LO (Recommended)
AUTO
ECO HI
Normal
ECO
Manual
Normal
276
