2013 Toyota Matrix Owners Manual

starting of the engine in cold weather.

● The 20 in 0W-20 indicates the viscosity characteristic of the oil when the oil is at high temperature. An oil with a higher viscosity (one with a higher value) may be better suited if the vehicle is operated at high speeds, or under extreme load conditions.

444

6-1. Specifications

How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use.

Cooling system

Capacity (Reference)

Coolant type

1.8 L 4-cylinder (2ZR-FE) engine 5.8 qt. (5.5 L, 4.8 Imp. qt.) 2.4 L 4-cylinder (2AZ-FE) engine 6.0 qt. (5.7 L, 5.0 Imp. qt.)

Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology

Do not use plain water alone.

445

6-1. Specifications

Ignition system

Spark plug Make

1.8 L 4-cylinder (2ZR-FE) engine DENSO SC20HR11
2.4 L 4-cylinder (2AZ-FE) engine DENSO SK20R11
DENSO SK16R11
NGK IFR6A11
NGK IFR5A11

Gap

0.043 in. (1.1 mm)

NOTICE

■Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust spark plug gap.

12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (Voltage checked 20 minutes after the engine and all the lights turned off) 5 A max.

Electrical system

Battery

Open voltage at 68°F (20°C):

Charging rates

446

6-1. Specifications

1.8 L 4-cylinder (2ZR-FE) engine 2.0 qt. (1.9 L, 1.7 Imp. qt.) 2.4 L 4-cylinder (2AZ-FE) engine 2.6 qt. (2.5 L, 2.2 Imp. qt.)

Use either of the following: • “TOYOTA Genuine Manual Transmission Gear Oil LV” • Other gear oil that meets API GL-4 and SAE 75W specifications

Manual transmission

Gear oil capacity (Reference)

Gear oil type

NOTICE

■Manual transmission gear oil

Please be aware that depending on the particular characteristics of the gear oil used or the operating conditions, idle sound, shift feeling and/or fuel effi- ciency may be different or affected. Toyota recommends to use “TOYOTA Genuine Manual Transmission Gear Oil LV” to achieve optimal performance.

447

6-1. Specifications

Automatic transmission

Fluid capacity (Reference)

1.8 L 4-cylinder (2ZR-FE) engine 6.9 qt. (6.5 L, 5.7 Imp. qt.) 2.4 L 4-cylinder (2AZ-FE) engine (2WD models) 8.2 qt. (7.8 L, 6.9 Imp. qt.) 2.4 L 4-cylinder (2AZ-FE) engine (AWD models) 8.6 qt. (8.1 L, 7.1 Imp. qt.)

Fluid type

Toyota Genuine ATF WS

NOTICE

■Automatic transmission fluid type

Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.

448

6-1. Specifications

Rear differential (AWD models)

Oil capacity Oil type

Recommended oil viscosity

Transfer (AWD models)

Oil capacity Oil type

Recommended oil viscosity

Clutch

Pedal free play Fluid type

0.5 qt. (0.5 L, 0.4 Imp. qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

0.8 qt. (0.8 L, 0.7 Imp. qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

0.2 ⎯ 0.6 in. (5 ⎯ 15 mm) SAE J1703 or FMVSS No.116 DOT 3

449

6-1. Specifications

Brakes

Pedal clearance*1

1.8 L 4-cylinder (2ZR-FE) engine 3.4 in. (87 mm) 2.4 L 4-cylinder (2AZ-FE) engine • AWD models: 3.4 in. (87 mm) • 2WD models with P215/45R18 tires: 3.4 in. (87 mm) • 2WD models with tires other than the above: 3.3 in. (85 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) 0.04 in. (1.0 mm) 0.04 in. (1.0 mm) 6 ⎯ 9 clicks SAE J1703 or FMVSS No.116 DOT 3

Pedal free play Brake pad wear limit Parking brake lining wear limit*2
Parking brake lever travel*3
Fluid type *1: Minimum pedal clearance when depressed with a force of 66 lbf (294 N, 30

kgf) while the engine is running

*2: 2.4 L 4-cylinder (2AZ-FE) engine with 18-inch tires or AWD models *3: Parking brake lever travel when pulled up with a force of 44 lbf (200 N, 20

kgf)

450

6-1. Specifications

Steering

Free play

Tires and wheels

16-inch tires

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Less than 1.2 in. (30 mm)

P205/55R16 89H, T135/80R16 101M or T135/70R17 102M

2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) AWD models Front: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar)

Wheel size

Wheel nut torque

16 × 6 1/2 J, 16 × 4T or 17 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

451

6-1. Specifications

17-inch tires

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size

Wheel nut torque

18-inch tires

P215/45R17 87W, T135/80R16 101M or T135/70R17 102M

2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) AWD models Front: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar)

17 × 7 J, 16 × 4T or 17 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P215/45R18 89W, T135/70R17 102M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 18 × 7 J, 17 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

452

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

Headlights Low beam High beam Front turn signal/park- ing and front side marker lights Front fog lights (if equipped) Rear turn signal lights Stop/tail and rear side marker lights License plate lights Back-up lights Personal lights Interior light

Exterior

Interior

A: H11 halogen bulbs C: Wedge base bulbs (clear) E: Double end bulbs

51
60

9006
9005

3457NA

27/7

⎯

⎯

55

21

7443

21/5

⎯ 921
⎯

16
B: HB3 halogen bulbs D: Wedge base bulbs (amber) F: HB4 halogen bulbs

⎯

Type

453

6-1. Specifications Fuel information

Your vehicle must use only unleaded gasoline. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.

■Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

■If your engine knocks

●Consult your Toyota dealer. ●You may occasionally notice light knocking for a short time while acceler-

ating or driving uphill. This is normal and there is no need for concern.

■Gasoline quality

In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

■Gasoline quality standards

●Automotive manufacturers in the U.S., the Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.

●The WWFC consists of four categories that are based on required emis-

sion levels. In the U.S., category 4 has been adopted.

●The WWFC improves air quality by lowering emissions in vehicle fleets,

and improves customer satisfaction through better performance.

■Toyota recommends the use of gasoline containing detergent additives ●Toyota recommends the use of gasoline that contains detergent additives

to avoid build-up of engine deposits.

●All gasoline sold in the U.S. contains detergent additives to clean and/or

keep clean intake systems.

454

6-1. Specifications

■Toyota recommends the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

■Toyota does not recommend blended gasoline

DO NOT use gasoline containing more than 10% ethanol.

(15% ethanol)

(50% ethanol)

(85% ethanol)

●Use only gasoline containing a maxi-

mum of 10% ethanol. DO NOT use any flex-fuel or gasoline that could contain more than 10% etha- nol, including from any pump labeled E15, E30, E50, E85 (which are only some examples of fuel containing more than 10% ethanol).

●If you use gasohol in your Toyota, be sure that it has an octane rating no

lower than 87.

●Toyota does not recommend the use of gasoline containing methanol.

■Toyota does not recommend gasoline containing MMT

Some gasoline contains octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

455

6-1. Specifications

NOTICE

■Notice on fuel quality

●Do not use improper fuels. If improper fuels are used the engine will be

damaged.

●Do not use leaded gasoline.

Leaded gasoline can cause damage to your vehicle’s catalytic converters causing the emission control system to malfunction.

●Do not use gasohol other than that stated here.

Other gasohol may cause fuel system damage or vehicle performance problems.

●Using unleaded gasoline with an octane number or rating lower than that

stated here will cause persistent heavy knocking. At worst, this will lead to engine damage.

■Fuel-related poor driveability

If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

■When refueling with gasohol

Take care not to spill gasohol. It can damage your vehicle's paint.

456

6-1. Specifications Tire information

Typical tire symbols

Full-size tire

Compact spare tire

Tire size DOT and Tire Identification Number (TIN) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators

(→P. 460) (→P. 459)

(→P. 349)

457

6-1. Specifications

Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube main- tains the air pressure. Load limit at maximum cold tire inflation pressure Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. Summer tires or all season tires (→P. 354) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. “TEMPORARY USE ONLY” (→P. 417) A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded into its sidewall. This tire is designed for temporary emergency use only.

(→P. 353) (→P. 451)

458

6-1. Specifications

Typical DOT and Tire Identification Number (TIN)

Identification Number

DOT symbol* Tire (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional type code (3 or 4 letters) Manufacturing week Manufacturing year *: The DOT symbol certifies that to applicable Federal Motor Vehicle Safety Standards.

tire conforms

the

tire

459

The illustration indicates typical tire size.

Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol (alphabet with one letter)

Section width Tire height Wheel diameter

6-1. Specifications

Tire size

■ Typical tire size information

■ Tire dimensions

460

6-1. Specifications

Tire section names

Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer

Uniform Tire Quality Grading

This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.

Your Toyota dealer will help answer any questions you may have as you read this information.

■ DOT quality grades

All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

461

6-1. Specifications

■ Treadwear

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

■ Traction AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turn- ing) traction.

■ Temperature A, B, C

The temperature grades are A (the highest), B, and C, represent- ing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speci- fied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passen- ger car tires must meet under the Federal Motor Vehicle Safety Stan- dard No.109. Grades B and A represent higher levels of performance on the labo- ratory test wheel than the minimum required by law.

462

6-1. Specifications

Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.

Glossary of tire terminology

Tire related term

Meaning

Cold tire inflation pres- sure

Maximum inflation pressure

Recommended infla- tion pressure

Accessory weight

Curb weight

Maximum loaded vehi- cle weight

Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer The combined weight (in excess of those stan- dard items which may be replaced) of auto- matic transmission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory-installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight

463

6-1. Specifications

Tire related term

Normal occupant weight

Occupant distribution

Production options weight

Rim

Rim diameter (Wheel diameter) Rim size designation

Rim type designation

Rim width Vehicle capacity weight (Total load capacity)

Vehicle maximum load on the tire

Vehicle normal load on the tire

464

Meaning

150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows Distribution of occupants in a vehicle as speci- fied in the third column of Table 1* below The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated

Nominal diameter of the bead seat

Rim diameter and width The industry manufacturer's designation for a rim by style or code Nominal distance between rim flanges The rated cargo and luggage load plus 150 lb. (68 kg) times the vehicle's designated seating capacity The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two The load on an individual tire that is determined by distributing to each axle its share of curb weight, accessory weight, and normal occu- pant weight (distributed in accordance with Table 1* below), and dividing by two

Tire related term

Weather side

Bead

Bead separation

Bias ply tire

Carcass

Chunking

Cord

Cord separation

Cracking

CT

Extra load tire

Groove

Innerliner

6-1. Specifications

Meaning

The surface area of the rim not covered by the inflated tire The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components in the bead A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the cen- terline of the tread The tire structure, except tread and sidewall rubber which, when inflated, bears the load The breaking away of pieces of the tread or sidewall The strands forming the plies in the tire The parting of cords from adjacent rubber com- pounds Any parting within the tread, sidewall, or inner- liner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The space between two adjacent tread ribs The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire

465

6-1. Specifications

Tire related term

Innerliner separation

Intended outboard sidewall

Light truck (LT) tire

Load rating

Maximum load rating

Maximum permissible inflation pressure

Measuring rim

Open splice

Outer diameter

Overall width

Passenger car tire

466

Meaning

The parting of the innerliner from cord material in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or

(b) The outward facing sidewall of an asym-

metrical tire that has a particular side that must always face outward when mounted on a vehicle

A tire designated by its manufacturer as prima- rily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry for a given inflation pressure The load rating for a tire at the maximum per- missible inflation pressure for that tire The maximum cold inflation pressure to which a tire may be inflated The rim on which a tire is fitted for physical dimension requirements Any parting at any junction of tread, sidewall, or innerliner that extends to cord material The overall diameter of an inflated new tire The linear distance between the exteriors of the sidewalls of an inflated tire, including eleva- tions due to labeling, decorations, or protective bands or ribs A tire intended for use on passenger cars, mul- tipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less.

Tire related term

Ply

Ply separation

Pneumatic tire

Radial ply tire

Reinforced tire

Section width

Sidewall

Sidewall separation

Snow tire

Test rim

6-1. Specifications

Meaning

A layer of rubber-coated parallel cords A parting of rubber compound between adja- cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and bead The parting of the rubber compound from the cord material in the sidewall A tire that attains a traction index equal to or greater than 110, compared to the ASTM E- 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Signal Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( least one sidewall The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire

) on at

467

6-1. Specifications

Tire related term

Meaning

Tread

Tread rib

Tread separation

Treadwear indicators (TWI)

That portion of a tire that comes into contact with the road A tread section running circumferentially around a tire Pulling away of the tread from the tire carcass The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread The fixture used to hold the wheel and tire assembly securely during testing

Wheel-holding fixture *: Table 1 ⎯ Occupant loading and distribution for vehicle normal load

for various designated seating capacities

Designated seating capacity, Number of

occupants 2 through 4

5 through 10

11 through 15

16 through 20

Vehicle normal load, Number of occupants

Occupant distribution in a normally loaded vehi-

cle

2 in front

2 in front, 1 in second

seat

2 in front, 1 in second seat, 1 in third seat, 1

in fourth seat

2 in front, 2 in second seat, 2 in third seat, 1

in fourth seat

468

6-2. Customization Customizable features

Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer.

Item

Function

Default setting

Wireless remote control

On

Customized

setting

Off

Wireless remote con- trol (if equipped) (→P. 28)

Unlocking operation

Automatic door lock function to be activated if door is not opened after being unlocked

Time elapsed before automatic door lock function is activated if door is not opened after being unlocked

Operation signal (Emergency flashers) Operation signal (Buzzer) Door lock buzzer Panic function

Driver's door unlocked in one step, all doors unlocked in two

steps

All doors

unlocked in one

step

On

Off

60 seconds

30 seconds

120 seconds

On

On

On On

Off

Off

Off Off

469

6-2. Customization

Item

Function

Default setting

Customized

setting

Door lock (vehicles with power door lock system) (→P. 31)

Driver's door unlocked in one step, all doors unlocked in two

steps

Off

On

On

Unlocking using a key

Opening driver's door unlocks all doors Shifting gears to P unlocks all doors. (vehi- cles with an automatic transmission) Shifting gears to posi- tion other than P locks all doors. (vehicles with an automatic transmis- sion)

All doors

unlocked in one

step

On

Off

Off

Time elapsed before lights turn off

15 seconds

7.5 seconds

30 seconds

Illumination (→P. 279)

Seat belt reminder (→P. 400)

Operation when the doors are unlocked (vehicles with power door lock system) Operation after the engine switch is turned to the “LOCK” position Vehicle speed linked seat belt reminder buzzer

On

On

On

Off

Off

Off

470

6-3. Initialization Items to initialize

The following items must be initialized for normal system operation in cases such as after maintenance is performed on the vehicle.

Item

Maintenance data (U.S.A. only)

Tire pressure warning system (if equipped)

When to initialize

Reference

After the maintenance is performed

P. 321

• When rotating the tires on vehicles differing with front and rear tire infla- tion pressure. • When changing the tire size.

P. 350

471

6-3. Initialization

472

Reporting safety defects for U.S. owners

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA can- not become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Ave, S.E., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

504

Seat belt instructions for Canadian owners (in French)

The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.

Utilisation correcte des ceintures de sécurité

● Déroulez la sangle diagonale de telle sorte qu'elle passe bien sur l'épaule, sans pour autant être en contact avec le cou ou glisser de l'épaule.

● Placez la sangle abdominale le plus bas possible sur les hanches.

● Réglez la position du dossier de siège. Asseyez-vous le dos le plus droit possible et calez- vous bien dans le siège.

● Ne vrillez pas la ceinture de

sécurité.

505

Guide confort de ceinture de sécurité (sièges arrière latéraux)

Si la sangle diagonale est proche du cou d’une personne, utilisez le guide confort de la ceinture de sécurité.

Sortez le guide confort de la pochette.

Glissez la ceinture dans la fente du guide.

Le cordon élastique doit être derrière la ceinture de sécurité.

Attachez-vous, positionnez ceinture et relâchez-la.

la

ÉTAPE

ÉTAPE

ÉTAPE

506

■ Ceinture de sécurité latérale arrière

Si la ceinture de sécurité est sortie de son guide, repassez-la dedans avant de l'utiliser.

Entretien et soin

■ Ceintures de sécurité

Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Vérifiez régulièrement que les ceintures ne sont pas effilochées, entaillées ou exagérément usées.

ATTENTION

■ Détérioration et usure des ceintures de sécurité

Inspectez les ceintures de sécurité périodiquement. Contrôlez qu'elles ne sont pas entaillées, effilochées et que leurs ancrages ne sont pas desserrés. Ne pas utiliser une ceinture de sécurité défectueuse avant qu'elle ne soit remplacée. Une ceinture de sécurité défectueuse n'apporte aucune garantie de protection de l'occupant en cas d'accident.

507

SRS airbag instructions for Canadian owners (in French)

The following is a French explanation of SRS airbag instructions

extracted from the SRS airbag section in this manual.

See the SRS airbag section for more detailed SRS airbag instructions in English.

Airbags frontaux Airbag conducteur et passager avant Participent à la protection de la tête et du thorax du conducteur et du passager avant contre les chocs avec des éléments de l'habitacle. Airbags latéraux et rideau Airbags latéraux Participent à la protection du haut du corps des occupants assis aux places avant. Airbags rideau Participent principalement à la protection de la tête des occupants assis aux places extérieures.

508

Composition du système d’airbags

Capteurs d’airbag avant Système de classification de l'occupant du siège passager avant (ECU et capteurs) Capteurs de porte Airbag passager avant Airbags latéraux de Prétensionneurs ceintures de sécurité et limiteurs de force Capteurs d’airbags latéraux et rideau Airbags rideau Témoins indicateurs “PASSENGER AIR BAG ON” et “PASSENGER AIR BAG OFF”

électronique

Témoin d'alerte SRS Contacteur de boucle de ceinture sécurité de passager avant Boîtier d’airbags Capteurs rideau Airbag conducteur Contacteur de boucle de ceinture sécurité conducteur Capteur de position du siège conducteur

airbags

des

de

509

Votre véhicule est équipé de ADVANCED AIRBAGS conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). Le boîtier électronique (ECU) des sacs de sécurité gonflables régule le déploiement de ces derniers sur la base des informations qu'il reçoit des capteurs, etc. indiqués ci-dessus dans le schéma illustrant les composants du système. Parmi ces informations figurent la gravité du choc et l'occupation du véhicule par les passagers. Le déploiement rapide des airbags est obtenu au moyen d'une réaction chimique dans les dispositifs pyrotechniques, qui produit un gaz inoffensif permettant d'amortir le mouvement des occupants.

510

ATTENTION

■ Précautions avec les airbags SRS

Respectez les précautions suivantes concernant les airbags. Autrement, des blessures graves, voire mortelles, pourraient s'ensuivre. ●Le conducteur et tous les passagers à bord du véhicule doivent porter leur

ceinture de sécurité correctement. Les airbags SRS sont des dispositifs de protection complémentaires aux ceintures de sécurité.

●L'airbag SRS conducteur se déploie avec une violence considérable, qui peut être très dangereuse voire mortelle si le conducteur se trouve très près de l’airbag. L’autorité fédérale chargée de la sécurité routière aux États-Unis (“NHTSA”) conseille:

Sachant que la zone de danger pour l’airbag conducteur se trouve dans les premiers 2 à 3 in. (50 à 75 mm) de déploiement, vous disposez d’une marge de sécurité confortable en vous plaçant à 10 in. (250 mm) de votre airbag conducteur. Cette distance est à mesurer entre le moyeu du volant et le sternum. Si vous êtes assis à moins de 10 in. (250 mm), vous pouvez changer votre position de conduite de différentes façons:

• Reculez votre siège le plus possible, de manière à pouvoir encore

atteindre confortablement les pédales.

• Inclinez légèrement le dossier du siège.

Bien que les véhicules puissent être différents les uns des autres, la plupart des conducteurs peuvent s'asseoir à une distance de 10 in. (250 mm), même avec le siège conducteur complètement avancé, simplement en inclinant un peu le dossier de siège. Si vous avez des difficultés à voir la route après avoir incliné votre siège, utilisez un coussin ferme et antidérapant pour vous rehausser ou, si votre véhicule est équipé du réglage en hauteur du siège, remontez-le.

• Si votre volant est réglable, inclinez-le vers le bas. Cela a pour effet d'orienter l’airbag en direction de votre poitrine plutôt que de votre tête et de votre cou.

Réglez votre siège selon ces recommandations de la NHTSA, tout en conservant le contrôle des pédales, du volant et la vue des commandes du tableau de bord.

511

ATTENTION

■ Précautions avec les airbags SRS

●Si vous attachez une rallonge de ceinture de sécurité aux boucles de ceinture de sécurité avant, mais pas au pêne de la ceinture de sécurité, les airbags SRS frontaux détectent que le conducteur et le passager avant ont attaché leur ceinture de sécurité, alors même que ce n'est pas le cas. Dans ce cas, il se peut que les airbags SRS frontaux pas correctement en cas d'accident, et vous risquez d'être tué ou grièvement blessé. Veillez à porter la ceinture de sécurité avec la rallonge de ceinture de sécurité.

déploient

ne

se

●L’airbag SRS passager avant se déploie également avec une violence considérable, qui peut être très dangereuse voire mortelle si le passager avant se trouve très près de l’airbag. Éloignez le siège passager avant au maximum de l’airbag et réglez le dossier de siège de sorte à être assis bien droit dans le siège.

512

ATTENTION

■ Précautions avec les airbags SRS

●Les nourrissons et les enfants qui ne sont pas correctement assis et/ou protégés peuvent être grièvement blessés ou tués par le déploiement d'un airbag. Installez dans un siège de sécurité enfant les enfants trop jeunes pour pouvoir utiliser la ceinture de sécurité. Toyota recommande vivement que les nourrissons et les jeunes enfants soient installés sur le siège arrière du véhicule et convenablement attachés. Les sièges arrière sont les plus sûrs pour les nourrissons et les enfants. ((cid:111)P. 103)

●Ne pas s'asseoir sur le bord du siège et ne pas s'appuyer contre la planche de bord.

513

ATTENTION

■ Précautions avec les airbags SRS

●Ne laissez pas un enfant rester debout devant l’airbag SRS passager avant ou bien s'asseoir sur les genoux du passager avant.

●Ne conduisez pas le véhicule lorsque le conducteur ou le passager avant a quelque chose de posé sur les genoux. ●Ne vous appuyez pas contre la porte, contre le rail latéral de toit ou contre les montants avant, latéraux et arrière.

●Interdisez à quiconque de s'agenouiller sur le siège passager en appui contre la porte ou de sortir la tête ou les mains à l'extérieur du véhicule.

●Ne fixez ni ne posez aucun objet sur la la garniture

planche de bord ou centrale du moyeu de volant. Au déploiement des airbags SRS conducteur et passager avant, ces objets risquent de se transformer en projectiles.

514

ATTENTION

■ Précautions avec les airbags SRS

●Ne rien fixer aux portes, à la vitre du pare-brise, aux vitres latérales, aux montants avant et arrière, au rail latéral de toit et à la poignée de maintien.

●Ne

suspendez aux

crochets à vêtements aucun cintre nu ni aucun objet dur. En cas de déploiement des airbags rideau SRS, tous ces objets pourraient se transformer en projectiles et vous causer des blessures graves, voire mortelles.

●N'utilisez aucun accessoire de siège venant recouvrir les zones de déploiement des airbags SRS latéraux, car il risquerait d'en gêner le déploiement.

●Évitez de faire subir des chocs ou des pressions excessives aux zones

renfermant les composants des airbags SRS ((cid:111)P. 509). En effet, cela pourrait entraîner un fonctionnement anormal des airbags SRS.

●Ne touchez aucun composant du système immédiatement après le déclenchement (gonflage) des airbags SRS, car ils sont alors encore très chauds.

515

ATTENTION

■ Précautions avec les airbags SRS

●Si vous avez des difficultés à respirer après le déploiement de l’airbag SRS, ouvrez une porte ou une vitre pour faire entrer de l'air frais, ou bien descendez du véhicule si cela ne présente pas de danger. Essuyez tout résidu dès que possible afin d'éviter d'éventuelles irritations de la peau.

●Si les parties renfermant les airbags SRS, telles que la garniture du volant et les garnitures de montants avant et arrière, apparaissent abîmées ou craquelées, faites-les remplacer par votre concessionnaire Toyota.

■ Modification et mise au rebut des éléments du système d’airbags SRS Consultez impérativement votre concessionnaire Toyota si vous avez besoin d'intervenir sur votre véhicule ou de procéder à l'une des modifications suivantes. Les airbags SRS risquent de ne pas fonctionner correctement ou de se déployer (gonflage) accidentellement, provoquant ainsi des blessures graves, voire mortelles. ●Installation, dépose, démontage et réparations des airbags SRS. ●Réparations, modifications, démontage ou remplacement du volant, du tableau de bord, de la planche de bord, des sièges ou de leur garnissage, des montants avant, latéraux et arrière ou du rail latéral de toit.

●Réparations ou modifications des ailes avant, du bouclier avant ou des

flancs de l'habitacle.

●Installation de chasse-neige, de treuils, etc., sur la calandre (pare-buffle,

pare-kangourou, etc.).

●Modification du système de suspension du véhicule. ●Installation d'appareils électroniques, tels qu'un radioémetteur/récepteur

ou d'un lecteur CD.

●Aménagements du véhicule visant à permettre sa conduite par une

personne atteinte d'un handicap physique.

516

Abbreviation list Abbreviation/Acronym list

ABBREVIATIONS MEANING

2WD 4WD A/C ABS ACC ALR AWD CRS ECU EDR ELR EPS GAWR GCWR GVWR

I/M

LATCH LED M + S MMT MTBE OBD SRS TIN TPMS TRAC TWR

486

2 Wheel Drive 4 Wheel Drive Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor All Wheel Drive Child Restraint System Electronic Control Unit Event Data Recorder Emergency Locking Retractor Electric Power Steering Gross Axle Weight Rating Gross Combination Weight Rating Gross Vehicle Weight Rating Emission inspection and maintenance Lower Anchors and Tethers for Children Light Emitting Diode Mud and Snow Methylcyclopentadienyl Manganese Tricarbonyl Methyl Tertiary Butyl Ether On Board Diagnostics Supplemental Restraint System Tire Identification Number Tire Pressure Warning System Traction Control Trailer Weight Rating

Abbreviation list

ABBREVIATIONS MEANING

VIN VSC

Vehicle Identification Number Vehicle Stability Control

487

What to do if... What to do if...

A tire punctures

P. 408 If you have a flat tire

The engine does not start

P. 422 If the engine will not start P. 68 Engine immobilizer system P. 425 If the battery is discharged

The shift lever cannot be moved out

P. 423 If the shift lever cannot be shifted

from P

The engine coolant temperature gauge enters the red zone

Steam can be seen coming from under the hood

P. 430 If your vehicle overheats

The key is lost

P. 424 If you lose your keys

The battery runs out

P. 425 If the battery is discharged

The doors cannot be locked

P. 31 Doors

The vehicle is stuck in mud or sand

P. 433 If the vehicle becomes stuck

A warning light or indicator light comes on

P. 397 If a warning light turns on or a

warning buzzer sounds...

498

What to do if...

■Warning lights

or

or

or

Brake system warning light

P. 397

Charging system warn- ing light P. 398

Low engine oil pressure warning light P. 398

Malfunction indicator lamp

P. 398

SRS warning light

P. 398

ABS warning light

P. 398

Electric power steering sys- tem warning light P. 398

Active Torque Control 4WD sys- tem warning light P. 398

Maintenance required reminder light P. 400

Tire pressure warning light P. 400

Low windshield washer fluid level warning light

P. 400

Slip indicator light

P. 398

Cruise control indicator light* P. 398

Open door warning light P. 400

Low fuel level warning light P. 400

Driver’s seat belt reminder light

P. 400

Front passenger’s seat belt reminder light P. 400

*: The light flashes to indicate a malfunction.

499

GAS STATION INFORMATION

Auxiliary catch lever

P. 330

Fuel filler door