2006 Toyota Matrix Owners Manual

opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your hands or eyes. If fluid gets on your hands or in your eyes, flush the af- fected area with clean water immedi- ately. If you still feel uncomfortable with your hands or eyes, go to the doctor.

NOTICE

If you spill some of the fluid, be sure to wipe it off to prevent it from dam- aging the parts or paintwork.

276

’06 MATRIX_U (L/O 0508)

Checking tire inflation pressure

D Use the manufacturer’s recom- mended wheels. Do not use wheels of different sizes and types. (See “Replacing wheels” on page 285 in this Section.)

Precautions for tires of four−wheel drive models

CAUTION

Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. D Keep your tire pressure at the proper level. (See “Checking tire inflation pressure” on page 277 in this Section.)

D Do not use tires (including snow tires) of different brands, sizes, construction or tread patterns. (See “Checking and replacing tires” on page 280
and “Installing snow tires and chains” on page 284 in this Section.)

D Do not use tires with different tread wear. To equalize the tire wear, rotate tires at the ap- propriate interval. (See “Rotat- ing tires” on page 283 in this Section.)

Type A

277

’06 MATRIX_U (L/O 0508)

Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on page 302 and 306. They are also on the tire and loading infor- mation label. You should check the tire inflation pressure every two weeks, or at least once a month. And do not forget the spare! The for checking tire inflation pressure should be observed: D The

instructions

be checked only when the tires are cold. If your vehicle has been parked for at least 3 hours and has not been driven for more than 1.5
km or 1 mile since, you will get an accurate cold tire inflation pres- sure reading.

following

pressure

should

D Always use a tire pressure gauge. The appearance of a tire can be misleading. Besides, tire inflation pressures that are even just a few pounds off can degrade ride and handling.

D Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quickly. Add com- pressed air in small quantities and check the pressure often until it reaches the specified pressure. D Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving. D Never exceed the vehicle capac- ity weight. Passenger and lug- gage weight should be located so that the vehicle is balanced.

Type B

278

’06 MATRIX_U (L/O 0508)

Tire pressure gauge

INSPECTION AND ADJUSTMENT PROCEDURE 1. Remove the tire valve cap. 2. Press the tip of the tire pressure

gauge to the tire valve.

3. Read the pressure using the grad-

uations of the gauge.

4. In case the tire inflation pressure is not within the prescribed range, insert the compressed air from the valve. In case of applying too much air, press the center of the valve and release the air to adjust.

5. After completing the tire inflation pressure measurement and ad- justment, apply soapy water to the valve and check for leakage.

6. Install the tire valve cap. If a gauge and air pump are not avail- able, have your vehicle checked by your Toyota dealer.

CAUTION

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as pos- sible.

Incorrect tire inflation pressure may waste fuel, reduce the comfort of driv- ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal- er.

CAUTION

Keep your tires properly inflated. Otherwise, the following condi- tions may occur and cause an ac- cident resulting in death or seri- ous injuries. Low tire pressure (underinfla- tion)— D Excessive wear D Uneven wear D Poor handling D Possibility of blowouts from an

overheated tire

D Poor sealing of the tire bead D Wheel deformation and/or tire

separation

D A greater possibility of tire

damage from road hazards

279

’06 MATRIX_U (L/O 0508)

Checking and replacing tires

Tread wear indicator

High tire pressure (overinfla- tion)— D Poor handling D Excessive wear D Uneven wear D A greater possibility of tire

damage from road hazards

CHECKING YOUR TIRES Check the tire’s tread for tread wear indicators. If the indicators show, replace the tires. The loca- tion of tread wear indicators is shown by the “TWI” or “∆” marks, etc., molded on the sidewall of each tire.

280

equipped

The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replace- ment. When the tread depth wears to 1.6 mm (0.06 in.) or less, the indica- tors will appear. If you can see the indicators in two or more adjacent grooves, the tire should be replaced. The lower the tread, the higher the risk of skidding. Vehicles with P215/50ZR17 tires: Your Toyota has been fitted with specially developed tires which provide exceptional dy- namic performance under general road conditions. However your riding comfort may worsen a little and road noise may increase during driving. You may also notice that your tires will wear more rapidly and tire grip performance will be reduced on the snowy and/or roads when compared to standard tires. Be sure to have snow tires or tire chains on the snowy and/or icy roads and drive carefully with the speed appropriate for road conditions.

icy

NOTICE

tire

profile

like Low P215/50ZR17 or P215/50R17 90H may have greater damage than usual tires to its tire wheel when receiving impact from the road surface. Therefore, pay attention to the following. z Be sure to use with proper tire pressure. If the tire pres- sure tire may have a greater damage. For detailed information about tire pressure, see page 306 in Section 8.

low,

the

is

z Avoid driving onto high, sharp−edged objects and oth- er road hazards. Failure to do so can lead to severe tire damage.

’06 MATRIX_U (L/O 0508)

The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.). If you have tire damage such as cuts, splits, cracks deep enough to expose the fabric, or bulges indi- cating internal damage, the tire should be replaced. If a tire often goes flat or cannot be properly repaired due to the size or location of a cut or other damage, it should be replaced. If you are not sure, consult with your Toyota dealer. If air loss occurs while driving, do not continue driving. Driving even a short distance can damage a tire beyond repair. Any tires which are over 6 years old must be checked by a qualified technician even if damage is not obvious. Tires deteriorate with age even if they have never or seldom been used. This applies also to the spare tire and tires stored for future use.

REPLACING YOUR TIRES When replacing a tire, use a tire of the same size and construction, and the same or greater maximum load as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Using any other size or type of tire may seriously affect handling, ride, speedometer/odometer calibration, ground clearance, and clearance be- tween the body and tires or snow chains. Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Cer- tification Label.

281

’06 MATRIX_U (L/O 0508)

Initial adjustment of the tire pres- sure warning system is necessary after you have rotated your tires. See “Tire pressure warning sys- tem” on page 126 in Section 1−7.

For details about the side wall of the tire and the Certification Label, see pages 193 and 195.

CAUTION

Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. D Do not mix radial, bias belted, or bias−ply tires on your ve- hicle, as this may cause dan- gerous handling characteris- tics resulting in loss of control. D Do not use tires other than the manufacturer’s recommended size, as this may cause danger- ous handling characteristics resulting in loss of control.

282

D Four−wheel drive models:

Do not use tires of different brands, sizes, construction or tread patterns, as this may cause dangerous handling characteristics in loss of control.

resulting

Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” on page 231 for tire change procedure. When a tire is replaced, the wheel should always be balanced. An unbalanced wheel may affect ve- hicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

Rotating tires

To equalize tire wear and help ex- tend tire life, Toyota recommends that you rotate your tires accord- ing to the maintenance schedule. (For scheduled maintenance infor- mation, please refer to the “Sched- uled Maintenance Guide” or “Own- er’s Supplement”.) However, the most appropriate tim- ing for tire rotation may vary ac- cording to your driving habits and road surface conditions. See “If you have a flat tire” on page 231 in Section 4 for tire change proce- dure.

Manual

’06 MATRIX_U (L/O 0508)

When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking.

CAUTION

Turning direction

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

Type A

Type B

Initial adjustment of the tire pres- sure warning system is necessary after you have rotated your tires. See “Tire pressure warning sys- tem” on page 126 in Section 1−7.

equipped

Vehicles with P215/50ZR17 tires: You have direc- tional tires, and a turning indicator marked on the side wall. Using tires on the wrong side of the ve- hicle will impair tire performance.

283

’06 MATRIX_U (L/O 0508)

CAUTION

the

following

Observe instructions. Otherwise, an accident may occur re- sulting in death or serious injuries. D Do not use snow tires other than the manufacturer’s recommended si- ze, as this may cause dangerous handling characteristics resulting in loss of control.

D Four−wheel drive models:

Do not use snow tires of different brands, sizes, construction or tread patterns, as this may cause danger- ous handling characteristics result- ing in loss of control.

SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires, which could cause loss of vehicle control. When storing removed tires, you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replacing.

CAUTION

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.

284

TIRE CHAIN SELECTION Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains. Regulations regarding the use of tire chains vary according to location or type of road, so always check local reg- ulations before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.

rear driving

0.5—1.0

the

’06 MATRIX_U (L/O 0508)

CAUTION

D Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

D When driving with chains installed, to drive carefully. Slow be sure down before entering curves to avoid losing control of the vehicle. Otherwise an accident may occur.

NOTICE

Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace a damaged wheel, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. This must be observed on compact spare tire, too. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

285

’06 MATRIX_U (L/O 0508)

Aluminum wheel precautions D When aluminum wheels, check tight after driving your vehicle the first 1600
km (1000 miles).

the wheel nuts are

installing that

repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

D When using tire chains, be careful not

to damage the aluminum wheels.

D Use only Toyota wheel nuts and for your aluminum

wrench designed wheels.

D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

CAUTION

Initial adjustment of the tire pressure warning system is necessary after you have replaced your wheels. See “Tire pressure warning system” on page 126
in Section 1−7.

the

following

instructions. Observe Otherwise, an accident may occur re- sulting in death or serious injuries. D Do not use wheels other than the manufacturer’s recommended size, as this may cause dangerous han- dling characteristics in loss of control.

resulting

D Four−wheel drive models:

Do not use wheels of different brands, sizes and types, as this may cause dangerous handling characteristics resulting in loss of control.

286

’06 MATRIX_U (L/O 0508)

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

288
289
290
291
292

287

’06 MATRIX_U (L/O 0508)

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

EMERGENCY MEASURES D If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

288

—Checking battery exterior

Terminals

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

’06 MATRIX_U (L/O 0508)

—Checking battery condition

NOTICE

Type A

z Be sure the engine and all accesso- ries are off before performing main- tenance.

z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY INDICATOR Check the battery condition by the indi- cator color.

Indicator color

Type A

Type B

Green

Blue

Dark

White

Clear or

light yellow

Red

Condition

Good

Charging necessary. Have battery checked by your Toyota dealer.

Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

289

’06 MATRIX_U (L/O 0508)

Checking and replacing fuses

Type A

Good

Blown

Type B

Good

Blown

Type C

Good

Blown

290

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” on page 266 in Sec- tion 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull the suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 307 in Section 8 for the functions controlled by each circuit.

Type A fuses can be pulled out by using the pull−out tool. The location of the pull− out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “INV” or “P/POINT” fuse, which may be dispens- able for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close to the rating as possible. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

’06 MATRIX_U (L/O 0508)

Adding washer fluid

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

You may use plain water as washer fluid. However, in cold areas where tempera- tures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

level

For vehicles sold in the U.S.A.—If any washer does not work, the washer tank may be empty. Check the washer fluid level on the level gauge. If the washer fluid is at “LOW”, add washer fluid. For vehicles sold in Canada—If any washer does not work or the low wind- shield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid.

291

’06 MATRIX_U (L/O 0508)

the

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the is caused by fogging temperature difference between the outside and the windshield fogs up in the rain. However, if there large drop of water on the inside of the lens, or if there is water pooled light, contact your Toyota dealer.

inside of

inside

lens,

is a

just

like

the

the

Light bulbs

Headlights (low)

Headlights (high)

Front fog lights

Parking, front side marker and front turn signal lights

Stop/tail and rear side marker lights

Rear turn signal lights

Back−up lights

High mounted stop light

License plate light

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

D To prevent burning yourself, do not replace the light bulbs while they are hot.

D Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

292

W Type

Bulb No. 9006

9005

9006

55

65

55

1157NA 27/8

7443

21/5

—

921

921

—

21

16

16

’06 MATRIX_U (L/O 0508)

—Headlights (low beam)

W Type

Bulb No. —

192

4.3

—

10

Light bulbs

Interior lights

Personal lights (on the inside rear view mirror without compass)

Personal lights (on the switch panel of the electric moon roof)

A: HB4 halogen bulbs B: HB3 halogen bulbs C: Single end bulbs D: Wedge base bulbs (clear) E: Wedge base bulbs (amber)

1. Open the hood. Turn the bulb base counterclockwise to the front of the vehicle as shown.

2. Unplug the connector. If the connector is tight, wiggle it.

293

’06 MATRIX_U (L/O 0508)

—Headlights (high beam)

3. Install a new bulb and connector

into the mounting hole.

Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

1. Open the hood.

LEFT−HAND HEADLIGHT: Remove the clip and pull out and twist the air cleaner duct unit as shown.

Removing the clip

294

Installing the clip

’06 MATRIX_U (L/O 0508)

2. Turn the bulb base counterclockwise

to the front of the vehicle.

3. Unplug the connector. If the connector is tight, wiggle it.

4. Install a new bulb and connector

into the mounting hole.

Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

295

’06 MATRIX_U (L/O 0508)

—Parking, front side marker and front turn signal lights

—Stop/tail, rear side marker, rear turn signal and back−up lights

—Front fog lights If either the left or right front fog light bulbs burns out, contact your Toyota dealer.

NOTICE

Do not try to replace the front fog light bulbs by yourself. You may dam- age the vehicle.

296

’06 MATRIX_U (L/O 0508)

—High mounted stoplight

a: Stop/tail and rear side marker light b: Rear turn signal light c: Back−up light

Remove the clips and the cover.

Removing the clips

Installing the clips

297

’06 MATRIX_U (L/O 0508)

—License plate lights

Remove the bolts with a Phillips−head screwdriver.

Remove the cover with a flathead screw- driver which is wrapped with a cloth.

298

’06 MATRIX_U (L/O 0508)

299

’06 MATRIX_U (L/O 0508)

300

’06 MATRIX_U (L/O 0508)

SECTION 8

SPECIFICATIONS Specifications Dimensions and weights Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

302
302
303
303
306
307

301

’06 MATRIX_U (L/O 0508)

Engine Model:

1ZZ−FE and 2ZZ−GE

Type:

4 cylinder in line, 4 cycle, gasoline

Bore and stroke, mm (in.):

1ZZ−FE engine

79.0 91.5 (3.11 3.60)

2ZZ−GE engine

82.0 85.0 (3.23 3.35)

Displacement, cm3 (cu. in.):

1ZZ−FE engine 2ZZ−GE engine

1794 (109.5) 1796 (109.6)

P205/55R16 89H tires

P215/50ZR17
P215/50R17 90H tires

4350 (171.3)

1775

1540
1550

(69.9) (60.6)∗2
(61.0)∗3

2600 (102.4)

1515

1495
1500

(59.6) (58.9)∗2
(59.1)∗3

4350 (171.3)

1775

(69.9)

1550

(61.0)

2600 (102.4)

1505

(59.3)

1485

(58.5)

385

(850)

385

(850)

680 (1500)

680 (1500)

Dimensions and weights

Overall length

Overall width

Overall height∗1

Wheelbase

Front tread

Rear tread

Vehicle capacity weight (occupants + luggage)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

kg (lb.)

Towing capacity (trailer weight + cargo weight) ∗1: Unladen vehicle ∗2: Two−wheel drive models ∗3: Four−wheel drive models

kg (lb.)

302

Fuel Fuel type:

1.8 L 4−cylinder (1ZZ−FE) engine

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

1.8 L 4−cylinder (2ZZ−GE) engine

Select premium unleaded gasoline with an Octane Rating of 91 (Research Oc- tane Number 96) or higher for opti- mum engine performance

Fuel tank capacity, L (gal., Imp. gal.):

Two−wheel drive models

50 (13.2, 11.0)

Four−wheel drive models

45 (11.9, 9.9)

’06 MATRIX_U (L/O 0508)

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

1.8 L 4−cylinder (1ZZ−FE) engine

Intake Exhaust

0.15—0.25 (0.006—0.010) 0.25—0.35 (0.010—0.014)

1.8 L 4−cylinder (2ZZ−GE) engine (on a roller side)

Intake Exhaust

0.08—0.18 (0.003—0.007) 0.22—0.32 (0.009—0.013)

Spark plug type:

1.8 L 4−cylinder (1ZZ−FE) engine

DENSO NGK

SK16R11
IFR5A11

is used

“Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

satisfy

the

ILSAC multigrade engine oil

Recommended oil viscosity:

SAE 5W−30

1.8 L 4−cylinder (2ZZ−GE) engine

DENSO NGK

SK20R11
IFR6A11

Spark plug gap, mm (in.):

1.1 (0.043)

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):

1.8 L 4−cylinder (1ZZ−FE) engine

With filter Without filter

4.2 (4.4, 3.7) 4.0 (4.2, 3.5)

1.8 L 4−cylinder (2ZZ−GE) engine

With filter Without filter

4.4 (4.7, 3.9) 4.2 (4.4, 3.7)

Outside temperature

Please contact your Toyota dealer for fur- ther details.

303

’06 MATRIX_U (L/O 0508)

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

1.8 L 4−cylinder (1ZZ−FE) engine

1.8 L 4−cylinder (2ZZ−GE) engine

6.5 (6.9, 5.7)

6.7 (7.0, 5.9)

Coolant type:

“Toyota Super Long Life Coolant” is used in your Toyota vehicle at factory fill. In order to avoid technical problems, only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. (Coolant with long−life hybrid organic acid technology is a combination of low phosphates and organic acids.) Do not use plain water alone. Please contact your Toyota dealer for further details.

304

BATTERY Open voltage∗ at 20_C (68_F):

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

Fully charged Half charged Discharged

∗: Voltage that is checked 20 minutes af- ter the key is removed with all the lights turned off Charging rates:

5 A max.

CLUTCH Pedal free play, mm (in.):

5—15 (0.2—0.6)

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

MANUAL TRANSAXLE Oil capacity, L (qt., Imp. qt.):

5−speed 6−speed

Oil type:

1.9 (2.0, 1.7) 2.3 (2.4, 2.0)

Gear oil API GL−4 or GL−5

Recommended oil viscosity:

SAE 75W−90

AUTOMATIC TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.):

Two−wheel drive models

Up to 3.0 (3.2, 2.6)

Four−wheel drive models

Up to 2.9 (3.1, 2.6)

Fluid type:

Toyota Genuine ATF Type T−IV

in

listed

Guide”

is necessary

Change automatic transmission fluid only as necessary. to change Generally, it automatic transmission fluid only if your vehicle is driven under one of the Special your Operating Conditions “Scheduled Maintenance or “Owner’s Manual Supplement”. When changing the automatic transmission fluid, use only “Toyota Genuine ATF Type T−IV” (ATF JWS3309 or NWS6500) to aid in assuring optimum transaxle performance. Notice: Using automatic transmission fluid other than “Toyota Genuine ATF Type T−IV” may cause deterioration in shift quality, locking up of your trans- mission accompanied by vibration, and ultimately damage the automatic trans- mission of your vehicle. Please contact your Toyota dealer for fur- ther details.

’06 MATRIX_U (L/O 0508)

TRANSFER (four−wheel drive models) Oil capacity, L (qt., Imp. qt.):

0.8 (0.8, 0.7)

Oil type:

Hypoid gear oil API GL−5
Recommended oil viscosity:

Above −18_C (0_F)

SAE 90

Below −18_C (0_F)

SAE 85W or 85W−90

REAR DIFFERENTIAL (four−wheel drive models) Oil capacity, L (qt., Imp. qt.):

0.5 (0.5, 0.4)

Oil type:

Hypoid gear oil API GL−5
Recommended oil viscosity:

Above −18_C (0_F)

SAE 90

Below −18_C (0_F)

SAE 85W or 85W−90

BRAKES Minimum pedal clearance when depressed with the force of 294 N (30 kgf, 66 lbf) with the engine running, mm (in.): Without anti−lock brake system

78 (3.07)

With anti−lock brake system

76 (2.99)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):

5—8 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRONrII or III

305

’06 MATRIX_U (L/O 0508)

Tires Tire size and cold tire inflation pressure: Front and rear

kPa (kgf/cm2 or bar, psi)

Tire size

Two−wheel drive models

Four−wheel drive models

P205/55R16 89H P215/50ZR17
P215/50R17 90H P205/55R16 89H

Front

220 (2.2, 32) 220 (2.2, 32) 220 (2.2, 32) 240 (2.4, 35)

Rear

220 (2.2, 32) 220 (2.2, 32) 220 (2.2, 32) 220 (2.2, 32)

Wheel size

16 6 1/2JJ

17 7 JJ 17 7 JJ

16 6 1/2JJ

Spare

Tire size T135/70R16
T135/80R16

kPa (kgf/cm2 or bar, psi)

420 (4.2, 60) 420 (4.2, 60)

Wheel size 16 4T 16 4T

Wheel nut torque, N·m (kgf·m, ft·lbf):

103 (10.5, 77)

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Precautions for tires of four−wheel drive models” through “Aluminum wheel precautions”, pages 277 through 286, in Section 7−2.

306

Fuses

Engine compartment

’06 MATRIX_U (L/O 0508)

7. ETCS 10 A (1.8 L 4−cylinder [1ZZ− FE] engine with two−wheel drive models only): Electronic throttle con- trol system

8. AMP 30 A: Audio system 9. MAIN 30 A: Starting system, “AM2”

fuse

10. DOME 15 A: Audio system, navigation system, clock, personal lights, interior lights, open door warning light, wireless remote control system

11. HORN 10 A: Horn 12. HAZARD 10 A: Emergency

flashers,

turn signal lights

13. EFI 15 A: Multiport fuel injection sys- injection tem/sequential multiport system, emission control system, “EFI” fuse

fuel

14. ALT−S 5 A: Charging system 15. HEAD LH LWR 10 A: Left−hand head-

light (low beam)

16. HEAD RH LWR 10 A: Right−hand

headlight (low beam)

17. EFI2 15 A: (1.8 L 4−cylinder [1ZZ−FE] engine with two−wheel drive models only): Multiport fuel injection system/ sequential multiport fuel injection sys- tem, emission control system

307

Instrument panel

Fuses (type A) 1. FOG 15 A: Front fog lights 2. HEAD LH UPR 10 A: Left−hand head-

light (high beam)

3. HEAD RH UPR 10 A: Right−hand headlight (high beam), headlight high beam indicator light

4. SPARE 30 A: Spare fuse 5. SPARE 15 A: Spare fuse 6. SPARE 10 A: Spare fuse

’06 MATRIX_U (L/O 0508)

30. ECU−B 10 A: Daytime running

light

system

31. CIG 15 A: Power outlet (12 VDC/on the instrument panel) or cigarette light- er, audio system, clock, shift lock con- trol system

32. GAUGE 10 A: Gauges and meters, air conditioning system, daytime running light system, charging system, auto anti−glare inside rear view mirror, pow- er windows, cruise control system, rear window defogger, back−up lights, front passenger’s seat belt reminder light, emergency flasher

33. WASHER 15 A: Windshield washer,

rear window washer

34. M−HTR/DEF I−UP 10 A: Engine control

system

Fuses (type B) 35. ABS NO.1 30 A: Anti−lock brake sys- traction control system, vehicle tem, stability control system, brake assist system

36. RDI FAN 40 A: Electric cooling fan

18. TAIL 15 A: Tail

lights, lights, instrument panel ment cluster lights, clock

license plate lights, instru-

19. OBD 7.5 A: On−board diagnosis sys-

tem

20. WIPER 25 A: Windshield wipers 21. AM2 15 A: Charging system, multiport fuel injection system/sequential multi- port fuel injection system, starting sys- tem, SRS airbag system

22. STOP 15 A: Stop lights, high mounted stoplight, anti−lock brake system, shift lock control system, multiport fuel in- jection system/sequential multiport fuel injection system, cruise control system 23. DOOR 25 A: Power door lock system,

glass hatch opener switch

24. AM1 25 A: “CIG” fuse 25. ECU−IG 10 A: Electric cooling

fan, anti−lock brake system, traction control system, vehicle stability control system, brake assist system, shift lock control system, cruise control system

26. RR WIPER 15 A: Rear window wiper 27. A/C 10 A: Air conditioning system 28. INV 15 A: Power outlet (115 VAC) 29. P/POINT 15 A: Power outlet (12 VDC/

in the rear console box)

308

37. ABS NO.2 40 A (without vehicle sta- bility control system): Anti−lock brake system ABS NO.2 50 A (with vehicle stability control system): Anti−lock brake sys- tem, traction control system, vehicle stability control system, brake assist system

38. HEAD MAIN 40 A: “HEAD LH UPR”, “HEAD RH UPR”, “HEAD LH LWR” and “HEAD RH LWR” fuses

39. AIR PUMP 50 A (1.8 L 4−cylinder [1ZZ−FE] engine with four−wheel drive models and 1.8 L 4−cylinder [2ZZ−GE] engine only): Emission con- trol system

40. HTR 40 A: Air conditioning system 41. DEF 30 A: Rear window defogger,

“M−HTR/DEF I−UP” fuse

42. POWER 30 A: Power windows, electric

moon roof

Fuses (type C) 43. ALT 100 A: “ABS NO.1”, “ABS NO.2”, “RDI FAN”, “AM1”, “POWER”, “DOOR”, “ECU−B”, “TAIL”, “STOP”, “P/POINT”, “INV” and “OBD” fuses, charging system

“FOG”,

“HTR”,

’06 MATRIX_U (L/O 0508)

SECTION 9

REPORTING SAFETY DEFECTS FOR U.S. OWNERS Reporting safety defects for U.S. owners Reporting safety defects for U.S. owners

. . . . . . . . . . . . . . . . . . . . . .

310

309

’06 MATRIX_U (L/O 0508)

To contact NHTSA, you may ei- ther call the Auto Safety Hotline toll−free at 1−800−424−9393 (or 366−0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hot- line.

Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately in- form the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll−free: 1−800−331−4331). If NHTSA receives similar com- plaints, it may open an investiga- tion, and if it finds that a safety defect exists in a group of ve- hicles, it may order a recall and remedy However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

campaign.

310

’06 MATRIX_U (L/O 0508)

Foreword

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build. This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully. When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, please call the following number: U.S. OWNERS:

D When traveling in the U.S. mainland or Canada:

Toyota Customer Experience Center

Toll−free:1−800−331−4331

D Hawaii:

Servco Automotive Customer Services

Toll−free:1−888−272−5515

CANADIAN OWNERS:

D When traveling in Canada or the U.S. mainland:

Toyota Canada Customer Interaction Centre

Toll−free:1−888−TOYOTA−8 or 1−888−869−6828
Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also. All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of continual product improvement, we reserve the right to make changes at any time without notice. Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. Please access our websites for further information. D The U.S. mainland D Hawaii D Canada

www.toyota.com www.toyotahawaii.com www.toyota.ca

© 2005 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.

’06 MATRIX_U (L/O 0508)

qU−7

Quick index D If a service reminder indicator or warning buzzer comes on D If your vehicle will not start D If your engine stalls while driving D If your vehicle overheats D If you have a flat tire D If your vehicle needs to be towed D Tips for driving during break−in period D How to start the engine D General maintenance D Complete index Gas station information Fuel type:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105
226
229
230
231
243
182
212
259
NO TAG

1.8 L 4−cylinder (1ZZ−FE) engine: UNLEADED gasoline, Octane Rating 87
(Research Octane Number 91) or higher 1.8 L 4−cylinder (2ZZ−GE) engine: Premium UNLEADED gasoline, Octane Rating 91 (Research Octane Number 96) or higher See page 182 for detailed information.

Fuel tank capacity:

Two−wheel drive models: 50 L (13.2 gal., 11.0 Imp. gal.) Four−wheel drive models: 45 L (11.9 gal., 9.9 Imp. gal.)

Engine oil:

ILSAC multigrade engine oil is recommended. See page 273 for detailed information.

Tire information: See pages 277 through 286. Tire inflation pressure: See page 306.

Publication No. OM12A21U Part No. 01999-12A21
Printed in Japan 01-0508-00

( U)

’06 MATRIX_U (L/O 0508)

Important information about this manual

Safety and vehicle damage warnings

Safety symbol

Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows:

CAUTION

This is a warning against anything which may cause is ignored. You are injury to people if the warning informed about what you must or must not do in order to reduce the risk of injury to yourself and others.

NOTICE

This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.

ii

the safety symbol When you see shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.

’06 MATRIX_U (L/O 0508)

Important information about your Toyota

Occupant restraint systems

Toyota encourages you and your family to take the time to read Section 1−3 of this Owner’s Manual carefully. In terms of helping you understand how you can receive the maximum benefit of the occupant restraint systems this vehicle provides, Section 1−3 of this Owner’s Manual is the most important Section for you and your family to read. Section 1−3 describes the function and operation concern- ing seats, seat belts, SRS airbags and child restraint sys- tems of this vehicle and some potential hazards you should be aware of. These systems work together along with the overall structure of this vehicle in order to provide occupant restraint in the event of a crash. The effect of each system is enhanced when it is used properly and together with other systems. No single occupant restraint system can, by itself, provide you or your family with the equal level of restraint which these systems can provide when used together. That is why it is important for you and your family to understand the purpose and proper use of each of these systems and how they relate to each other.

iii

The purpose of all occupant restraint systems is to help reduce the possibility of death or serious injury in the event of a collision. None of these systems, either individ- ually or together, can ensure that there is no injury in the event of collision. However, the more you know about these systems and how to use them properly, the greater your chances become of surviving an accident without death or serious injury.

Seat belts provide the primary restraint to all occupants of the vehicle, and every occupant of the vehicle should wear seat belts properly at all times. Children should always be secured in child restraint systems that are appropriate for their age and size. SRS (Supplemental Restraint System) airbags are, as their names imply, designed to work with, and be supplemental to, seat belts and are not substitutes for them. SRS airbags can be very effective in reducing the risk of head and chest injuries by preventing contact of the head and chest with interior portions of the vehicle.

In order to be effective, the SRS airbags must deploy with tremendous speed. The rapid deployment of the SRS air- bags makes the SRS airbags themselves potential sources of serious injury if an occupant is too close to an airbag, or if an object or some part of his or her body has been placed between the occupant and the airbag at the time of deployment. This is just one example of how the instruc- tions in Section 1−3 of this Owner’s Manual will help en- sure proper use of the occupant restraint systems, and increase the safety they can provide to you and your fami- ly in the event of an accident.

Toyota recommends you to read the provisions in Section 1−3 carefully and refer to them as needed during your time of ownership of this vehicle.

’06 MATRIX_U (L/O 0508)

Event data recorder

Your vehicle has computers that monitor and control cer- tain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Be- sides storing data useful for troubleshooting, there is a system to record data in a crash or a near car crash event. This is called an Event Data Recorder (EDR).