2004 Toyota Matrix Owners Manual

When returning the seatback to the upright position, make sure the seat- back is securely locked by pushing forward and rearward on the top of the seatback. Failure to do so will prevent seat belt from operating prop- erly.

You can use the front passenger’s seat- back as a temporary table only when the vehicle is stopped.

CAUTION

To avoid serious injury: D Do not set up the seatback table

while the vehicle is moving.

D Do not sit on the seatback table.

NOTICE

To prevent damage to the seat, avoid putting heavy loads on the temporary table.

32

Lower the head restraints to the lowest position. Pull up the lock release button and fold the seatback down. Each seatback can be folded separately. This will enlarge the luggage compartment as far as the seatbacks. See “—Stowage precautions” on page 192 in Section 2 for precautions when loading luggage.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

Head restraints

CAUTION

When returning the seatback to the upright position, observe the follow- ing precautions in order to prevent personal injury in a collision or sud- den stop: D Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback and that the red mark at the button on the top of the seatback cannot be seen. Failure to do so will pre- vent seat belt from operating prop- erly.

D Make sure the seat belts are not twisted or caught in the seatback and are arranged the proper position and are ready to use.

in

Front

Rear

33

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

You can use the rear right side seatback as a temporary table only when the ve- hicle is stopped.

CAUTION

To avoid serious injury: D Do not set up the seatback table

while the vehicle is moving.

D Do not sit on the seatback table.

NOTICE

To prevent damage to the seat, avoid putting heavy loads on the temporary table.

’04 MATRIX_U (L/O 0307)

Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. The seat belts provided for your vehicle are designed for people of adult size, large enough to properly wear them. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” on page 54 in this Section for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.

For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.

CAUTION

D Adjust the center of the head re- straint so that it is closest to the top of your ears.

D After adjusting the head restraint, make sure it is locked in position. the head re-

D Do not drive with

straints removed.

34

Do not allow any children to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. Holding a child in your arms does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.

recommendations. The

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

CAUTION

the vehicle

in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: D Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. D To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. In the event of a frontal collision, the more the seat is reclined, the greater the risk of personal injury.

’04 MATRIX_U (L/O 0307)

D Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.

D Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.

—Fastening front and rear seat belts

Tab

Buckle

D Keep the belts clean and dry.

If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers, or allow them to come into contact with the belt—they may se- verely weaken (See “Cleaning the interior” on page 239
in Section 5.)

the belts.

D Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.

tab

the

into

insert

Adjust the seat as needed and sit up straight and well back in the seat. To fasten your belt, pull it out of the re- tractor and the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.

35

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

is

then

When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” on page 54 in this Section.) To free the belt again, fully retract the belt and then pull the belt out once more. If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor.

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

D If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from injury.

36

’04 MATRIX_U (L/O 0307)

Take up slack

Too high

CAUTION

D Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on hips as possible.

D Do not place the shoulder belt un-

der your arm.

Keeps as low on hips as possible

the

lap and

the position of

Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

CAUTION

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause serious injures in a collision.

Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment, make sure the anchor is locked in position.

To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.

37

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

from your Toyota dealer

—Seat belt extender If your seat belts cannot be fastened se- curely because they are not long enough, a personalized seat belt extender is avail- able free of charge. Please contact your local Toyota dealer to order the proper required length for the extender. Bring the heaviest coat you ex- pect to wear for proper measurement and selection of length. Additional ordering in- formation is available at your Toyota deal- er.

CAUTION

the

When using the seat belt extender, following precautions. observe Failure to follow these instructions could reduce the effectiveness of the seat belt restraint system in case of an accident, increasing the chance of personal injury. D Remember that the extender pro- vided for you may not be safe when used on a different vehicle, for another person, or at a different seating position than the one origi- nally intended.

38

’04 MATRIX_U (L/O 0307)

D Be sure to wear the seat belt with- out the seat belt extender if you can fasten the seat belt without the extender.

in

the extender

D If the seat belt extender has been connected to the driver’s seat belt buckle without wearing the seat belt when using the driver’s seat, the SRS driver’s air- bag system will judge that the driv- er wears the seat belt even if not wearing it. In this case, the driver’s airbag may not activate correctly, causing death or serious injury in the event of collision. Be sure to wear the seat belt with the seat belt extender.

If

installing a child

D Do not use the seat belt extender when restraint system on the front or rear passen- ger seat. installing a child re- straint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of collision.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

—Seat belt pretensioners

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt and the seat belt extend- er are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

D If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from injury.

To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the “PRESS” signs on the buckle release buttons of the ex- tender and the seat belt are both facing outward as shown. You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extend- er itself. When not and store in the vehicle for future use.

in use, remove the extender

The driver and front passenger seat belt pretensioners are designed to be activated in response to a severe fron- tal impact. When the sensor detects a severe frontal impact, the front seat belts are quickly drawn back by the retractors so that the belts snugly restrain the occupants. The seat belt pretensioners are activated even with no passenger in the front seat. The seat belt pretensioners and SRS air- bags may not operate together in case of collisions at certain speeds and angles.

39

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

When the seat belt pretensioners are acti- vated, an operating noise may be heard and a small amount of non−toxic gas may be released. This does not indicate that a fire is occurring. This gas is normally harmless. Once been activated, remain locked.

the seat belt pretensioners have the seat belt retractors

CAUTION

Do not modify, remove, strike or open the seat belt pretensioner assemblies, airbag sensor or surrounding area or wiring. Failure to follow these instruc- tions may prevent the seat belt pre- tensioners from activating correctly, cause sudden operation of the system or disable the system, which could result in death or serious injury. Con- sult your Toyota dealer about any re- pair and modification.

NOTICE

consulting

Do not perform any of the following changes without your Toyota dealer. Such changes can interfere with proper operation of the seat belt pretensioners in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player

z Repairs on or near the front seat

belt retractor assemblies

z Modification of the suspension sys-

tem

z Modification of the front end struc-

ture

z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

z Repairs made on or near the front fenders, front end structure or con- sole

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

The seat belt pretensioner system mainly consists of the following components and their locations are shown in the illustra- tion. 1. Front airbag sensors 2. SRS warning light 3. Seat belt pretensioner assemblies 4. Airbag sensor assembly The seat belt pretensioners are controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.

40

’04 MATRIX_U (L/O 0307)

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. D When the ignition key is turned to the “ON” position, the light does not come on, remains on or flashes.

D The light comes on or starts flashing

while driving.

D If any seat belt does not retract or can not be pulled out due to a malfunction or activation of the relevant seat belt pretensioner.

D The seat belt pretensioner assembly or

surrounding area has been damaged.

light system monitors

This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the front seat belt pretensioners are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. (For details, see “Service reminder indicators and warning buzzers” on page 91 in Section 1−6.)

In the following cases, contact your Toyota dealer as soon as possible: D The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the seat belt pretensioners to operate. D Either seat belt pretensioner assembly scratched,

or cracked, or otherwise damaged.

surrounding area

is

41

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

SRS driver airbag and front passenger airbag

Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver when the SRS front airbags are inflated.

The SRS (Supplemental Restraint Sys- tem) front airbags are designed to pro- vide further protection for the driver and front passenger in addition to the primary safety protection provided by the seat belts. In response to a severe frontal impact, the SRS front airbags work together with the seat belts to help reduce injury by inflating. The SRS front airbags help re- duce injuries mainly to the driver’s or front passenger’s head or chest caused by hit- ting the vehicle interior. The is activated even with no passenger in the front seat. Always wear your seat belt properly.

front passenger airbag

42

CAUTION

D The SRS front airbag system is de- signed only as a supplement to the primary protection of the driver and front passenger seat belt systems. The driver and front passenger can be killed or seriously injured by the inflating airbags if they do not wear the available seat belts properly. During sudden braking just before a collision, an unrestrained driver or front passenger can move for- ward into direct contact with or close proximity to the airbag which may then deploy during the colli- sion. To ensure maximum protection in an accident, the driver and all passengers the vehicle must wear their seat belts properly. Wear- ing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For in- structions and precautions concern- ing the seat belt system, see “Seat belts” on page 34 in this Section.

in

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

restraint

D Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seat of the vehicle and proper- ly restrained. The rear seat is the safest for infants and children. For instructions concerning the installa- tion of a child restraint system, see “Child restraint” on page 54 in this Section.

that all

system.

The SRS front airbags are designed to deploy in severe (usually frontal) colli- sions where the magnitude and duration of the forward deceleration of the ve- hicle exceeds the designed threshold level. The SRS front airbags will deploy if the severity of the impact is above the de- signed threshold level, comparable to an approximate 25 km/h (15 mph) collision when the vehicles has the impact straight into a fixed barrier that does not move or deform. However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It in some collisions where the forward deceleration of the ve- hicle is very close to the designed thresh- old level, the SRS front airbags and the seat belt pretensioners may not activate together. Always wear your seat belts properly.

(e.g. a collision

is possible

that

this

Collision from the rear

Collision from the side

Vehicle rollover

The SRS front airbags are generally not designed to inflate if the vehicle is in- volved in a side or rear collision, if it rolls over, or if it is involved in a low− speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, de- ployment of the SRS front airbags may occur.

43

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

Hitting a curb, edge of pavement or hard surface

Falling into or jumping over a deep hole

Landing hard or vehicle falling

The SRS front airbags may also deploy if a serious impact occurs to the under- side of your vehicle. Some examples are shown in the illustration.

44

the

The SRS front airbag system mainly con- sists of following components, and their locations are shown in the illustra- tion. 1. Front airbag sensors 2. SRS warning light 3. Airbag module for front passenger

(airbag and inflator)

4. Driver’s seat belt buckle switch 5. Driver’s seat position sensor 6. Airbag sensor assembly 7. Airbag module for driver

(airbag and inflator)

The airbag sensor assembly consists of a safing sensor and airbag sensor.

fills

The front airbag sensors constantly moni- tor the forward deceleration of the vehicle. If an impact results in a forward decelera- tion beyond the designed threshold level, the system triggers the airbag inflators. At this time a chemical reaction in the infla- tors very quickly the airbags with non−toxic gas to help restrain the forward motion of the occupants. The front airbags then quickly deflate, so that there is no obstruction of the driver’s vision should it be necessary to continue driving. When the airbags inflate, they produce a loud noise and release some smoke and residue along with non−toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation with soap and water. If you can safely exit from the vehicle, you should do so imme- diately.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

CAUTION

The driver or front passenger who is too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: D The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.

D The front passenger sit as far back

as possible from the dashboard.

D All vehicle occupants be properly restrained using the available seat belts.

For instructions and precautions con- cerning the seating position, see “—Front seat precautions” on page 28 in this Section.

injuries, especially

Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, primarily to the head and chest, it may also cause other, less severe injuries to the face, chest, arms and hands. These are usually in the nature of minor burns or abrasions and swelling, but the force of a deploying airbag can cause more seri- ous if an occupant’s hands, arms, chest or head is in close proximity to the airbag module at the time of deployment. This is why it is important for to: avoid placing any object or part of the body between the occupant and the airbag module; sit straight and well back into the seat; wear the available seat belt properly; and sit as far as possible from the airbag module, while still maintaining control of the ve- hicle. Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment, so do not inflate only once. The windshield may be damaged by absorbing some of the force of the inflat- ing airbag.

touch! The airbags

the occupant

is

in use, since

D Do not sit on the edge of the seat or lean against the dashboard when the vehicle the front passenger airbag could inflate with considerable speed and force. Anyone who is up against, or very close to, an airbag when it inflates, can be killed or seriously injured. Sit up straight and well back in the seat, and always use your seat belt properly.

45

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

D Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” on page 54 in this Sec- tion.

D Do not put anything or any part of your baby on or in front of the dashboard or steering wheel pad that houses the front airbag sys- tem. They might restrict inflation or cause death or serious injury as they are projected rearward by the force of the deploying airbags. Like- wise, the driver and front passenger should not hold objects their arms or on their knees.

in

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

D Toyota strongly recommends that all infants and children be placed in the rear seat of the vehicle and be properly restrained.

D Do not allow a child to stand up or kneel on the front passenger seat, front passenger airbag since could considerable speed and the child may be killed or seriously in- jured.

the inflate with

force. Otherwise,

46

the

D Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, dashboard near front passenger airbag, front passenger airbag cover, front passenger airbag or airbag sensor assembly. Doing so may prevent the front airbag system from activating correctly, cause sudden activation of the system or disable the sys- tem, which could result in death or serious injury.

Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification. If you wish to modify your vehicle for the handicapped, consult with your Toyota dealer. It may dangerously in- terfere with the SRS front airbags op- eration.

’04 MATRIX_U (L/O 0307)

NOTICE

consulting

front airbag system

Do not perform any of the following changes without your Toyota dealer. Such changes can interfere with proper operation of the SRS in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player

z Modification of the suspension sys-

tem

z Modification of the front end struc-

ture

z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

z Repairs made on or near the front fenders, front end structure, con- sole, steering wheel or dashboard near the front passenger airbag

steering

column,

light system monitors

This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS side airbags are operat- ing properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. (For details, see “Service reminder indicators and warning buzzers” on page 91 in Section 1−6.)

47

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. D When the ignition key is turned to the “ON” position, the light does not come on, remains on or flashes.

D The light comes on or starts flashing

while driving.

In the following cases, contact your Toyota dealer as soon as possible: D The SRS front airbags have been in-

flated.

D The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS front airbags to inflate.

D The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.

passenger

airbag

front

48

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

SRS side airbags

The SRS (Supplemental Restraint Sys- tem) side airbags are designed to pro- vide further protection for the driver and front passenger in addition to the primary safety protection provided by the seat belts. In response to a severe side impact, the SRS side airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS side airbags help to reduce injuries mainly to the driver’s or front pas- senger’s chest. The SRS side airbag on the passenger seat is activated even with no passenger in the front seat. Always wear your seat belt properly.

Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and front passenger when the SRS side airbags are inflated.

CAUTION

D The SRS side airbag system is de- signed only as a supplement to the primary protection of the driver and front passenger seat belt systems. To ensure maximum protection in an accident, the driver and all pas- sengers in the vehicle must wear their seat belts properly. Wearing a seat belt properly during an acci- dent reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts” on page 34 in this Section.

restraint

D Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child Toyota strongly recommends in- fants and children be placed in the rear seats of the vehicle and prop- erly restrained. The rear seats are the safest for infants and children. For the installation of a child restraint sys- tem, see “Child restraint” on page 54 in this Section.

instructions concerning

that all

system.

D Do not allow anyone to lean his/her head or any part of his/her body against the front door or the area of the seat from which the SRS side airbag deploys even if he/she is a child seated in the child re- is dangerous if straint system. the SRS side airbag inflates, and the impact of the deploying airbag could cause death or serious injury to the occupant.

It

49

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

Collision from the rear

Collision from the front

Vehicle rollover

The SRS side airbags are not designed to inflate if the vehicle is involved in a front or rear collision, if it rolls over, or if it is involved in a low−speed side collision.

the

The SRS side airbag system mainly con- sists of following components, and their locations are shown in the illustra- tion. 1. SRS warning light 2. Side airbag modules

(airbag and inflator) 3. Side airbag sensors 4. Airbag sensor assembly The SRS side airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

from

The SRS side airbag system may not activate if the vehicle is subjected to a collision the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment as shown in the illustra- tion. The SRS side airbags are designed to inflate when the passenger compartment area suffers a severe the side. Always wear your seat belts properly.

impact

from

50

In a severe side impact, the side airbag sensor triggers the side airbag inflators. At this time a chemical reaction in the inflators quickly fills the airbags with non− toxic gas to help restrain the lateral mo- tion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non−toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation with soap and water. If you can safely exit from the vehicle, you should do so imme- diately. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Front seats may be hot for several min- utes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.

’04 MATRIX_U (L/O 0307)

CAUTION

SRS side airbags inflate with consid- erable force. To reduce the possibility of death or serious injury when they inflate, the driver and front passenger must: D Wear their seat belts properly. D Remain properly seated with their backs upright and against the seats at all times.

D Do not allow anyone to lean against the front door when the vehicle is in use, since the side airbag could inflates with considerable speed and force. Otherwise, he/she may be killed or be seriously injured. Special care should be taken espe- cially when you have a small child in the vehicle.

D Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight the seats on vehicles with side airbags.

the outer side of

to

51

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

D Do not use seat accessories which cover the parts where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.

D Do not modify or replace the seats or upholstery of the seats with side airbags. Such changes may prevent the side airbag system from activat- ing correctly, disable the system or cause the side airbags to inflate ac- cidentally, resulting in death or seri- ous injury.

Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification. If you wish to modify your vehicle for the handicapped, consult with your Toyota dealer. It may dangerously in- terfere with the SRS side airbags op- eration.

NOTICE

consulting

Do not perform any of the following changes without your Toyota dealer. Such changes can interfere with proper operation of the SRS side airbag system in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player

z Modification of the suspension sys-

tem

z Modification of the side structure of

the passenger compartment

z Repairs made on or near the con-

sole or front seat

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

D Do not attach a cup holder or any other device or object on or around the door. When the side airbag in- flates, the cup holder or any other device or object will be thrown with great force or the side airbag may not activate correctly, resulting in injury. Likewise, death or serious the driver and front passenger should not hold objects their arms or on their knees.

in

52

’04 MATRIX_U (L/O 0307)

If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. D When the ignition key is turned to the “ON” position, the light does not come on, remains on or flashes.

D The light comes on or starts flashing

while driving.

In the following cases, contact your Toyota dealer as soon as possible: D Any of

the SRS side airbags have

been inflated.

D The portion of the doors (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS side airbags to inflate.

D The surface of the seats with the side airbag (shaded is scratched, cracked, or otherwise dam- aged.

illustration)

the

in

53

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

light system monitors

This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS side airbags are operat- ing properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. (For details, see “Service reminder indicators and warning buzzers” on page 91 in Section 1−6.)

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

’04 MATRIX_U (L/O 0307)

Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- propriate child restraint systems for children. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” on page 34 in this Section for details.

CAUTION

D For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.

D Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, installed on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. D Never install a rear−facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the impact of the rapid infla- tion of the front passenger airbag could cause death or serious injury to the child if the rear−facing child restraint system is installed on the front passenger seat.

the

D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- inflate with senger airbag could considerable speed and force. Otherwise, the child may be killed or seriously injured.

54

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

if the child

D On vehicles with side airbags, do not allow the child to lean his/her head or any part of his/her body against the front door or the area of the seat from which the side air- bags deploy even is seated in the child restraint system. It is dangerous if the side airbag inflate, and the impact could cause death or serious injury to the child. D Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly se- cured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sud- den stop or accident.

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s in- structions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. restraint system should be The child installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than the passenger compartment. This will pre- vent the event of a sudden stop or accident.

injuring passengers

from

in

it

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 65 in this Section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 67 in this Sec- tion.

55

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

—Installation with seat belt

(A) Infant seat

(C) Booster seat

(A) INFANT SEAT INSTALLATION An infant seat must be used in rear− facing position only.

(B) Convertible seat

56

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

CAUTION

D Never install a rear−facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the impact of the rapid infla- tion of the front passenger airbag could cause death or serious injury to the child if the rear−facing child restraint system is installed on the front passenger seat.

the

lock mechanism of

D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

57

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

58

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.

installing, follow instructions about

installing

for

59

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

D On vehicles with side airbags, do not allow the child to lean his/her head or any part of his/her body against the front door or the area of the seat from which the side air- bags deploy even is seated in the child restraint system. It is dangerous if the side airbag inflate, and the impact could cause death or serious injury to the child.

if the child

CAUTION

D Never install a rear−facing child re- straint system on the front passen- ger seat. In the event of an acci- dent, the impact of the rapid infla- tion of the front passenger airbag could cause death or serious injury to the child if the rear−facing child restraint system is installed on the front passenger seat.

Move seat fully back

the

D A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- inflate with senger airbag could considerable speed and force. Otherwise, the child may be killed or seriously injured.

60

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

the

lock mechanism of

D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

CAUTION

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

61

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

62

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.

Move seat fully back

CAUTION

the

D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- senger airbag could inflate with considerable force. and speed Otherwise, the child may be killed or seriously injured.

63

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

D On vehicles with side airbags, do not allow the child to lean his/her head or any part of his/her body against the front door or the area of the seat from which the side air- bags deploy even is seated in the child restraint system. It is dangerous if the side airbag inflate, and the impact could cause death or serious injury to the child.

if the child

CAUTION

D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” on page 34 in this Section for details.

64

could

D Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

D For child’s safety, do not place the

shoulder belt under child’s arm.

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

—Using a top strap

D If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

2. To remove the child restraint system, the buckle release button and

press allow the belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

65

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

Anchor brackets

Symbol

Use the anchor brackets in the luggage compartment to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the location of the anchor bracket.

for each

installed

TO USE THE ANCHOR BRACKET: 1. Outside anchor brackets only—

Remove the head restraint.

2. Open the lid of the anchor bracket.

66

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

—Installation with child restraint lower anchorages

4. Outside anchor brackets only—

Replace the head restraint.

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of both outside rear seats. Child restraint systems complying with the FMVSS225 or CMVSS210.2 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

67

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

3. Securely

fasten

the child restraint

system with the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 54 in this Section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

’04 MATRIX_U (L/O 0307)

RESTRAINT

For owners in Canada The symbol on a child restraint system indicates the presence of a lower connec- tor system. CHILD INSTALLATION Type A— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages near the tag on the seatback.

SYSTEM

Canada only

Canada only

Type A

68

Type B

2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages near the tag on the seatback.

2. Latch the buckles onto the anchor-

ages.

it should be anchored. (For

If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 65 in this Section.)

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

the installation details, refer

For to the instruction manual equipped with each product.

CAUTION

D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

the

lock mechanism of

D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

69

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

70

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

SECTION 1− 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Vanity mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72
72
74
75
76

71

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

Tilt steering wheel

Outside rear view mirrors—

CAUTION

D Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

To change the steering wheel angle, hold the steering wheel, push down the lock the steering wheel to the desired angle and return the lever to its original position.

release

lever,

tilt

72

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

2004 MATRIX from Oct. ’03 Prod. (OM12861U)

’04 MATRIX_U (L/O 0307)

—Rear view mirror remote control