2010 Toyota FJ Cruiser Owners Manual

Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ●Excessive wear ●Uneven wear ●Poor handling ●Possibility of blowouts resulting from overheated tires ●Poor sealing of the tire bead ●Wheel deformation and/or tire separation ●A greater possibility of tire damage from road hazards

315

4-3. Do-it-yourself maintenance

NOTICE

■When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.

316

4-3. Do-it-yourself maintenance Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at your Toyota dealer. *: Conventionally referred to as “offset”. Toyota does not recommend using: ● Wheels of different sizes or types ● Used wheels ● Bent wheels that have been straightened

■ Aluminum wheel precautions (if equipped)

● Use only Toyota wheel nuts and wrench designed for use with

your aluminum wheels.

● When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1000 miles (1600 km).

● Be careful not to damage the aluminum wheels when using

tire chains.

● Use only Toyota genuine balance weights or equivalent and a

plastic or rubber hammer when balancing your wheels.

317

4-3. Do-it-yourself maintenance

■When replacing wheels

The wheels of your Toyota are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P. 309)

CAUTION

■When replacing wheels

●Do not use wheels that are a different size from those recommended in

the Owner’s Manual, as this may result in loss of handling control.

●Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or seri- ous injury.

NOTICE

■Replacing tire pressure warning valves and transmitters

●Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.

●Ensure that only Genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.

318

4-3. Do-it-yourself maintenance Air conditioning filter

The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. ■ Removal method

Turn the engine switch off.

Open the glove box.

Slide off the damper.

Push in each side of the glove box to disconnect the claws.

319

4-3. Do-it-yourself maintenance

Remove the filter case.

If the filter is dirty, clean by blowing air through the downward side.

compressed from

filter

the

Hold the air gun 2 in. (5 cm) from the filter and blow for approximately 2 minutes at 72 psi (500 kPa, 5.0 kgf/cm2
or bar). If it is not available, have the filter cleaned by your Toyota dealer.

Remove the air conditioning filter and replace it with a new one.

The “↑UP” marks shown on the filter should be pointing up.

■ Cleaning method

■ Replacement method

320

4-3. Do-it-yourself maintenance

■Checking interval

Inspect, clean and replace the air conditioning filter according to the mainte- nance schedule. In dusty areas or areas with heavy traffic flow, more fre- quent cleaning or early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

■If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

NOTICE

■To prevent damage to the system

●When using the air conditioning system, make sure that a filter is always

installed.

●When cleaning the filter, do not clean the filter with water.

321

4-3. Do-it-yourself maintenance Key battery

Replace the battery with a new one if it is discharged. ■ You will need the following items:

● Small Phillips-head screwdriver ● Lithium battery CR1616

■ Replacing the battery

Remove the screw and cover. Push the cover in the arrow direction.

Remove the module.

Remove the 2 screws to take out the lid.

Insert a new battery with the “+” terminal facing up.

322

4-3. Do-it-yourself maintenance

■If the key battery is discharged

The following symptoms may occur. ●The wireless remote control will not function properly. ●The operational range is reduced.

■Use a CR1616 lithium battery

●Batteries can be purchased at your Toyota dealer, jewelers, or camera

stores.

●Replace only with the same or equivalent type recommended by your

Toyota dealer.

●Dispose of used batteries according to the local laws.

CAUTION

■Removed battery and other parts

Keep away from children. These parts are small and if swallowed by a child they can cause choking.

NOTICE

■For normal operation after replacing the battery

Observe the following precautions to prevent accidents. ●Always work with dry hands.

Moisture may cause the battery to rust.

●Do not touch or move any other components inside the remote control. ●Do not bend either of the battery terminals.

323

4-3. Do-it-yourself maintenance Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.

Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.

■ Engine compartment

Type A

Push the tab in and lift the lid off.

Type B (if equipped)

Push the tab in and lift the lid off.

324

4-3. Do-it-yourself maintenance

■ Under the instrument panel

Remove the lid.

After a system failure, see “Fuse layout and amperage rat- ings” (→P. 328) for details about which fuse to check.

325

4-3. Do-it-yourself maintenance

Remove the fuse with the pull- out tool.

Check if the fuse has blown.

326

Type A

Type B

Type C

4-3. Do-it-yourself maintenance

Normal fuse Blown fuse it with one of an Replace appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid

327

4-3. Do-it-yourself maintenance

Fuse layout and amperage ratings

■ Engine compartment

Type A

Type B (if equipped)

328

4-3. Do-it-yourself maintenance

Ampere

Circuit

Fuse SPARE SPARE TOWING TAIL RR FOG

5 OFFROAD LP

10 A 15 A 15 A 10 A 15 A

STOP

10 A

AUX LP

8 OBD

HEAD (LO RH)

10 HEAD (LO LH)

11 HEAD (HI RH) 12 HEAD (HI LH)

13 EFI NO.2

14

INJ

15 DRL 16 DEFOG

15 A 7.5 A

10 A

10 A

10 A 10 A

10 A

10 A

7.5 A 30 A

Spare fuse Spare fuse Trailer lights No circuit Offroad lamp Stop lights, high mounted stop- light, anti-lock brake system, trac- tion control system, active traction control system, vehicle stability control system, AUTO LSD system, multiport fuel injection system/ sequential multiport fuel injection system, shift lock system Driving lamp On-board diagnosis system Right-hand headlight (low beam)*1
Right-hand headlight*2
Left-hand headlight (low beam)*1
Left-hand headlight*2
Right-hand headlight (high beam) Left-hand headlight (high beam) Multiport fuel injection system/ sequential multiport fuel injection system Multiport fuel injection system/ sequential multiport fuel injection system Daytime running light system Rear window defogger

329

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

17 DEFOG NO.2

7.5 A

18 DOME

19 RADIO NO.1

20 ECU-B

21 ALT-S 22 HORN

23 A/F HEATER

24 TRN-HAZ

25 ETCS

26 EFI

27 DR/LCK

28 TOWING 29 RADIO NO.2

30 AM1

31

J/B

330

10 A

20 A

10 A

7.5 A 10 A

15 A

15 A

10 A

20 A

20 A

15 A 20 A

50 A

50 A

Multiport fuel injection system/ sequential multiport fuel injection system Interior light, personal lights, engine switch light, clock, acces- sory meter, meter and gauge Audio system Air conditioning system, multiplex communication system, SRS air- bag system, front passenger occu- pant classification system Charging system Horn Multiport fuel injection system/ sequential multiport fuel injection system Turn signal lights, emergency flashers Multiport fuel injection system/ sequential multiport fuel injection system, electronic throttle control system EFI NO.2, multiport fuel injection system/sequential multiport fuel injection system Door lock system, multiplex com- munication system Towing converter Audio system ACC, ECU-IG, IG1, RR WSH, FR WIP-WSH, 4WD/DIFF and STA TAIL, PWR OUTLET, POWER

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

32 ABS MTR

40 A

33 AM2

30 A

34 ABS SOL

30 A

35 ALT

36 HEATER 37 AC 115V

120 A

60 A 80 A

Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system IGN and GAUGE, multiport fuel injection system/sequential multi- port fuel injection system, starting system Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system AM1, AC 115V, DEFOG, DEFOG NO.2, STOP, OBD, J/B, TOWING TAIL, AUX LP and OFFROAD LP Air conditioning system Power outlet

*1: Vehicles with daytime running light *2: Vehicles without daytime running light

331

4-3. Do-it-yourself maintenance

■ Under the instrument panel

6 7 8

10 11

12

Fuse

Ampere

Circuit

IGN

10 A

2 GAUGE

FR WIP-WSH

4WD/DIFF

PWR OUTLET

RR WSH

7.5 A 30 A

20 A

15 A

15 A

Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, vehicle stability control system, traction control system, active trac- tion control system, AUTO LSD system, SRS airbag system, front passenger occupant classification system Meter and gauge Windshield wipers and washer Four-wheel drive system, rear dif- ferential lock system Power outlet Rear window wiper and washer, multiplex communication system

332

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

ECU-IG

10 A

IG1

15 A

STA

10 TAIL

11 ACC

12 POWER

7.5 A

10 A

7.5 A

30 A

Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system, multi- port fuel injection system/sequen- tial multiport fuel injection system, cruise control system, back door lock system, shift lock system, mul- tiplex communication system Turn signal lights, air conditioning system, charging system, clutch start cancel switch, anti-lock brake system, traction control system, active traction control system, vehi- cle stability control system, AUTO LSD system, back-up lights, intui- tive parking assist, rear differential lock system, power outlet, acces- sory meter, meter and gauge, rear view monitor system Starting system, clutch start cancel switch, power outlet Tail lights, license plate lights, park- ing lights, instrument panel light control, illuminations Shift lock system, outside rear view mirrors, audio system, power out- let, clock, accessory meter, multi- plex communication system Power windows

333

4-3. Do-it-yourself maintenance

■After a fuse is replaced

●If the lights do not turn on even after the fuse has been replaced, a bulb

may need replacement. (→P. 335)

●If the replaced fuse blows again, have the vehicle inspected by your

Toyota dealer.

■If there is an overload in the circuits

The fuses are designed to blow before the entire wiring harness is damaged.

CAUTION

■To prevent system breakdowns and vehicle fire

Observe the following precautions. Failing to do so may cause damage, and possibly a fire or injury. ●Never use a fuse of a higher amperage rating than indicated, or use any

other object in place of a fuse.

●Always use a genuine Toyota fuse or equivalent.

Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.

●Do not modify the fuse or the fuse box.

NOTICE

■Before replacing fuses

Have the cause of electrical overload determined and repaired by your Toy- ota dealer as soon as possible.

334

4-3. Do-it-yourself maintenance Light bulbs

You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. ■ Prepare a replacement light bulb.

Check the wattage of the light bulb being replaced. (→P. 397)

■ Front bulb locations

Headlights

Front turn signal/parking and front side marker lights

335

4-3. Do-it-yourself maintenance

■ Rear bulb locations

Stop/tail and rear side marker lights

Back-up lights

Rear turn signal lights

License plate lights

Replacing light bulbs

■ Headlights

Unplug the connector.

336

4-3. Do-it-yourself maintenance

Remove the rubber cover.

Release spring.

the bulb

retaining

Remove the bulb.

To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.

337

4-3. Do-it-yourself maintenance

■ Front turn signal/parking and front side marker lights

Turn the bulb base counterclock- wise.

Remove the light bulb.

338

4-3. Do-it-yourself maintenance

■ Back-up lights, stop/tail and rear side marker and rear turn

signal light bulbs

● Removing the sub woofer speaker (vehicles with sub woofer)

Remove the speaker cover.

Remove the cover.

Installing the sub woofer speaker (→P. 342)

Remove the sub woofer speaker.

Disconnect the connector. Remove the 4 screws and the sub woofer speaker.

339

4-3. Do-it-yourself maintenance

● Removing the back-up, stop/tail and rear side marker and rear turn

signal light bulbs

Open the back door and remove the cover.

Using a flathead screwdriver or equivalent which is wrapped with a cloth.

Turn the bulb bases counter- clockwise.

Back-up light Stop/tail and rear side marker lights Rear turn signal light

Remove the light bulb.

Back-up light Stop/tail and rear side marker lights Rear turn signal light

340

4-3. Do-it-yourself maintenance

■ License plate lights

Remove the screws and cover.

Remove the light bulb.

■ Lights other than the above

If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. • Outside rear view mirror illumination lights (if equipped) • High mounted stoplight

341

4-3. Do-it-yourself maintenance

■Condensation build-up on the inside of the lens

Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. ●Large drops of water are built up on the inside of the lens. ●Water has built up inside the headlight.

■LED high mounted stoplight

The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

■Installing the sub woofer speaker (vehicles with sub woofer)

Install the rubber inside the panel as shown in the illustration.

CAUTION

■Replacing light bulbs

●Turn off the headlights. Do not attempt to replace the bulb immediately

after turning off the headlights. The bulbs become very hot and may cause burns.

●Do not touch the glass portion of the light bulb with bare hands. Hold the

bulb by the plastic or metal portion. If the bulb is scratched or dropped it may blow out or crack.

●Fully install light bulbs and any parts used to secure them. Failing to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.

■To prevent damage or fire

Make sure bulbs are fully seated and locked.

342

5-1. Essential information Emergency flashers

Use the emergency flashers if the vehicle malfunctions or is involved in an accident.

Press the switch to flash all the turn signal lights. To turn them off, press the switch once again.

NOTICE

■To prevent battery discharge

Do not leave the emergency flashers on longer than necessary when the engine is not running.

344

5-1. Essential information If your vehicle needs to be towed

If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly or flat bed truck.

Before towing

The following may indicate a problem with your transmission. Contact your Toyota dealer before towing. ● The engine is running, but the vehicle will not move. ● The vehicle makes an abnormal sound.

Emergency towing

If a tow truck is not available, in an emergency your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet. This should only attempted on hard, surfaced roads for short distances at low speeds. A driver must be in the vehicle to steer and operate the brakes. The vehicle’s wheels, drive train, axles, steering and brakes must be in good condition.

Towing eyelet

345

5-1. Essential information

■Emergency towing procedure

The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models with an automatic transmission: Shift the front-wheel drive control lever in H2. 4WD models with a manual transmission: Unlock the center differ- ential. Put the shift lever in N. Release the parking brake.

CAUTION

■Caution while towing

●Use extreme caution when towing the vehicle.

Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains.

●If the engine is not running, the power assist for the brakes and steering

will not function, making steering and braking more difficult.

NOTICE

■To prevent causing serious damage to the transmission

(vehicles with an automatic transmission) Never tow this vehicle from the rear with the four wheels on the ground. This may cause serious damage to the transmission.

■Emergency towing eyelet precautions

●Before emergency towing, check that the eyelet is not broken or damaged. ●Fasten the towing cable or chain securely to the eyelet. ●Do not jerk the eyelet. Apply steady and even force. ●To avoid damaging the eyelet, do not pull from the side or at a vertical

angle. Always pull straight ahead.

346

5-1. Essential information

Towing with a sling-type truck

NOTICE

■To prevent body damage

Do not tow with a sling-type truck, either from the front or rear.

Towing with a wheel lift-type truck from the front

Use a towing dolly under the rear wheels.

NOTICE

■To prevent causing serious damage to the transmission

Never tow this vehicle wheels on the ground.

347

5-1. Essential information

Towing with a wheel lift-type truck from the rear

2WD models

Turn the engine switch to the ACC position.

4WD models

Vehicles with a manual transmis- sion: Use a towing dolly under the front wheels. Vehicles with an automatic trans- mission: When not using a tow- ing dolly, turn the engine switch to the ACC position, shift the shift lever to N and shift the front- wheel drive control lever in H2.

NOTICE

■To prevent causing serious damage to the transmission (4WD models)

Never tow this vehicle wheels on the ground.

■To prevent damaging the vehicle

●Do not tow the vehicle with the key removed or in the LOCK position.

The steering lock mechanism is not strong enough to hold the front wheel straight.

●When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.

348

Using a flat bed truck

Front

5-1. Essential information

If your Toyota is transported by a flat bed truck, it should be tied down at the locations shown in the illustration.

If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. Apply the parking brake firmly.

349

5-1. Essential information If you think something is wrong

If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms

● Fluid leaks under the vehicle

(Water dripping from the air conditioning after use is normal.)

● Flat-looking tires or uneven tire wear ● Engine coolant temperature gauge needle continually points

higher than normal

● Voltmeter continually points higher or lower than normal.

■ Audible symptoms

● Changes in exhaust sound ● Excessive tire squeal when cornering ● Strange noises related to the suspension system ● Pinging or other noises related to the engine

■ Operational symptoms

● Engine missing, stumbling or running rough ● Appreciable loss of power ● Vehicle pulls heavily to one side when braking ● Vehicle pulls heavily to one side when driving on a level road ● Loss of brake effectiveness, spongy feeling, pedal almost

touches the floor

350

5-1. Essential information Fuel pump shut off system

To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine.

Follow the procedure below to restart the engine after the system is activated.

Turn the engine switch to the ACC or LOCK position. Restart the engine.

NOTICE

■Before starting the engine

Inspect the ground under the vehicle. If you find that fuel has leaked onto the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine.

351

5-1. Essential information Event data recorder

Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.

In a crash or a near car crash event

The SRS airbag sensor assembly contains the EDR. In a crash or a near car crash event, this device may record some or all of the follow- ing information: ● Engine speed ● Whether the brake pedal was applied or not ● Vehicle speed ● To what extent the accelerator pedal was depressed ● Position of the transmission shift lever ● Whether the driver and front passenger wore seat belts or not ● Driver’s seat position ● SRS airbag deployment data ● SRS airbag system diagnostic data ● Front passenger’s occupant classification The information above is intended to be used for the purpose of improving vehicle safety performance. Unlike general data recorders, the EDR does not record sound data such as conversation between passengers.

352

5-1. Essential information

Disclosure of the data

Toyota will not disclose the data recorded in an EDR to a third party except when: ● An agreement from the vehicle’s owner (or the leasing company for

a leased vehicle) is obtained

● Officially requested by the police or other authorities ● Used as a defense for Toyota in a law suit ● Ordered by a court of law However, if necessary Toyota will: ● Use the data for research on Toyota vehicle safety performance ● Disclose the data to a third party for research purposes without dis- closing details of the vehicle owner, and only when it is deemed necessary

● Disclose summarized data cleared of vehicle identification informa-

tion to a non-Toyota organization for research purposes

353

5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds...

Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system.

Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.

The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Brake system warning light • Low brake fluid • Malfunction in the brake system This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released, the system is operating nor- mally.

354

5-2. Steps to take in an emergency

Stop the vehicle immediately.

The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Charging system warning light Indicates a malfunction in the vehicle’s charging sys- tem.

Low engine oil pressure warning light Indicates that the engine oil pressure is too low*.

*: The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the engine oil level dipstick.

Have the vehicle inspected immediately.

Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately.

Warning light

Warning light/Details

Malfunction indicator lamp Indicates a malfunction in: • The electronic engine control system; • The electronic throttle control system; • The electronic automatic transmission control sys- tem; or • Emission control system. SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system.

355

5-2. Steps to take in an emergency

Warning light

Warning light/Details

ABS warning light Indicates a malfunction in: • The ABS; or • The brake assist system.

(U.S.A.)

(Canada)

Slip indicator The indicator comes on to indicate a malfunction in: • The VSC; • The TRAC; or • The active traction control system (if equipped); or • The AUTO LSD system (2WD models). Automatic transmission fluid temperature warn- ing light Indicates that the automatic transmission fluid tem- perature is too high.

(Automatic transmis-

sion vehicles)

(if equipped)

Unengaged “Park” warning light Malfunction in the transmission “Park” mechanism.

356

5-2. Steps to take in an emergency

Follow the correction procedures.

After taking the specified steps to correct the suspected problem, check that the warning light turns off.

Warning light

Warning light/Details

Correction procedure

(On the instrument

cluster)

(On the center panel)

Open door warning light Indicates that a door, back door or glass hatch is not fully closed.

Check that all doors and glass hatch are closed.

Driver’s seat belt reminder light (warning buzzer)*1
Warns the driver to fas- ten his/her seat belt. Front passenger’s seat belt reminder light (warning buzzer)*2
Warns the front passen- ger to fasten his/her seat belt. Tire pressure warning light • When the light comes on: Low tire inflation pres- sure. • When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warning system.

Fasten the seat belt.

Fasten the seat belt.

Adjust the tire inflation pressure. (including spare tire) Have the system checked by your Toyota dealer.

357

5-2. Steps to take in an emergency

Warning light

Warning light/Details

Correction procedure

Low fuel level warning light Low level of fuel.

Refuel the vehicle.

(Canada only)

(U.S.A.)

Low washer fluid warn- ing light Low level of washer fluid.

Maintenance required reminder light*3
• Inidicates that mainte- nance is required accord- ing to the driven distance on the maintenance schedule. • Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the main- tenance data has been reset. • Comes on and remains on if the distance driven exceedes 5000 miles (8000 km) after the main- tenance data has been reset. (The Indicator will not work properly unless the maintenance data has been reset.)

Fill the tank.

If necessary, perform maintenance.

Perform the necessary maintenance. Please reset the main- tenance data after the maintenance is per- formed. See page “Reset the maintenance data”

*1: Driver's seat belt reminder:

The driver’s seat belt reminder sounds to alert the driver that his or her seat belt is not fastened. Once the engine switch is turned to the ON or START position, the buzzer sounds for 6 seconds. If the vehicle has reached a

358

5-2. Steps to take in an emergency

speed of at least 12 mph (20 km/h), the buzzer sounds intermittently for 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 more seconds.

*2: Front passenger’s seat belt reminder:

The front passenger’s seat belt reminder sounds to alert the front passenger that his or her seat belt is not fastened. The buzzer sounds intermittently for 10 seconds after the vehicle has reached a speed of at least 12 mph (20 km/ h). Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 more seconds.

*3: Maintenance required reminder:

Refer to the seperate “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” for the maintenance interval applicable to your vehicle.

359

5-2. Steps to take in an emergency

■Key reminder buzzer

The buzzer indicates that the key has not been removed (with the engine switch in the ACC or LOCK position and the driver’s door opened).

■If the malfunction indicator lamp comes on while driving

First check the following: ●Is your vehicle low on gas?

If it is, refuel the vehicle immediately.

●Is the fuel tank cap loose?

If it is, tighten it securely.

The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible.

■Front passenger detection sensor and passenger seat belt reminder

If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light to flash and buzzer to sound.

■When the tire pressure warning light comes on

Check the tire inflation pressure and adjust to the appropriate level.

■The tire pressure warning light may turn on due to natural causes

The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temper- ature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).

■When a tire is replaced with a spare tire

The spare tire is also equipped with the tire pressure warning valve and transmitter. The tire pressure warning light will turn on if the tire inflation pressure of the spare tire is low. If a tire goes flat, even though the flat tire is replaced with the spare tire, the warning light does not turn off. Replace the spare tire with the repaired tire and adjust the proper tire inflation pressure. The tire pressure warning light will turn off after a few minutes.

360

5-2. Steps to take in an emergency

■If the tire pressure warning system is inoperative

The tire pressure warning system will be disabled in the following condi- tions: (When the condition becomes normal, the system will work properly.) ●If tires not equipped with tire pressure warning valves and transmit-

ters are used.

●If the ID code on the tire pressure warning valves and transmitters is

not registered in the tire pressure warning computer.

●If the tire inflation pressure is 73 psi (500 kPa, 5.1 kgf/cm2 or bar) or

higher. The tire pressure warning system may be disabled in the following conditions: (When the condition becomes normal, the system will work properly.) ●If electronic devices or facilities using similar radio wave frequencies

are nearby.

●If a radio set at similar frequencies is in use in the vehicle. ●If a window tint that affects the radio wave signals is installed. ●If there is a lot of snow or ice on the vehicle, in particular around the

wheels or wheel housings.

●If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.)

●If tire chains are used. ●If the spare tire is in a location subject to poor radio wave signal

reception.

●If a large metallic object which can interfere with signal reception is

put in the luggage compartment.

■If the tire pressure warning light comes on after blinking for 1

minute frequently If the tire pressure warning light comes on after blinking for 1 minute fre- quently when the engine switch is turned to the ON position, have it checked by your Toyota dealer.

361

5-2. Steps to take in an emergency

■Customization that can be configured at Toyota dealer

The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features →P. 412)

CAUTION

■If the tire pressure warning light comes on

Be sure to observe the following precautions. Failure to do so could cause loss of vehicle control and result in death or serious injury. ●Stop your vehicle in a safe place as soon as possible. Adjust the tire

inflation pressure immediately.

●If the tire pressure warning light comes on even after tire inflation pres- sure adjustment, it is probable that you have a flat tire. Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer.

●Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate,

you could lose control of the steering wheel or the brakes.

■If a blowout or sudden air leakage should occur

The tire pressure warning system may not activate immediately.

■Maintenance of the tire

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label). (If your vehicle has tires of a differ- ent size than the size indicated on the vehicle placard or tire inflation pressure label [tire and load information label], you should determine the proper tire inflation pressure for those tires.)

362

5-2. Steps to take in an emergency

CAUTION

■Maintenance of the tire

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS-tire pressure warning system) that illuminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale (tire pressure warning light) illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS (tire pressure warning system) is not a sub- stitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale (tire pressure warning light). Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light). When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illumi- nated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illumi- nated, the system may not be able to detect or signal low tire pressure as intended. TPMS (tire pressure warning system) malfunctions may occur for a vari- ety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS (tire pressure warning system) from functioning properly. Always check the TPMS (tire pres- sure warning system) malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alter- nate tires and wheels allow the TPMS (tire pressure warning system) to continue to function properly.

363

5-2. Steps to take in an emergency

NOTICE

■Precaution when installing a different tire

When a tire of a different specification or maker is installed, the tire pres- sure warning system may not operate properly.

364

5-2. Steps to take in an emergency

If you have a flat tire

365

5-2. Steps to take in an emergency

Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle

● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ● Shift the shift lever to P (automatic transmission) or R (manual

transmission).

● Stop the engine. ● Turn on the emergency flashers.

■ Location of the spare tire, jack and tools

Jack

Tool bag

Spare tire

■ Tools

Jack handle

Extension

Wheel nut wrench

Remover*

Wrench*

*: Vehicles with rear view monitor system

366

Taking out the jack and tool bag

5-2. Steps to take in an emergency

Remove the cover and loosen the strap.

Loosen and remove the jack.

Tighten Loosen

Taking out the spare tire (vehicles without rear view monitor system)

Vehicles with an aluminum wheel: Remove the wheel orna- ment using the wheel nut wrench as shown.

To protect the wheel and wheel ornament, place a rag between the wheel nut wrench and the wheel ornament, as shown in the illustration.

367

5-2. Steps to take in an emergency

Turn the hold-down nuts counter- clockwise with the wheel nut wrench and remove them.

Taking out the spare tire (vehicles with rear view monitor system)

Remove the bolt cover.

Bolt cover

Remove the bolt which fixes the spare wheel cover using the wrench in the tool bag (→P. 364).

368

5-2. Steps to take in an emergency

Remove the spare wheel cover.

Turn the hold-down nuts counter- clockwise with the wheel nut wrench and remove them.

369

5-2. Steps to take in an emergency

Replacing a flat tire

Chock the tires.

Flat tire

Front