2010 Toyota FJ Cruiser Owners Manual

●Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an obstacle. Particular instances where this may occur are listed below. • There is dirt, snow or ice on a sensor. • A sensor is frozen. • A sensor is covered in any way. • The vehicle is leaning considerably to one side. • On an extremely bumpy road, on an incline, on gravel, or on grass. • The vicinity of the vehicle is noisy due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.

• There is another vehicle equipped with parking assist sensors in the

vicinity.

• A sensor is coated with a sheet of spray or heavy rain. • The vehicle is equipped with a fender pole or radio antenna. • A bumper or sensor receives a strong impact. • The vehicle is approaching a tall or right-angled curb. • In harsh sunlight or intense cold weather. • The area directly under the bumpers is not detected.

Objects lower than the sensors or thin stakes etc. may be detected ini- tially, but as they draw closer, they may cease to be detected.

• A towing hitch is mounted to the vehicle. • A non-genuine Toyota suspension (lowered suspension etc.) is

installed.

• When attaching a two-way radio antenna. • When a towing eyelet is mounted on your vehicle. • When the bumper is damaged.

In addition to the examples above, there are instances in which, because of their shapes, signs and other objects may be judged by a sensor to be closer than they are.

156

2-4. Using other driving systems

●The shape of the obstacle may prevent a sensor from detecting it. Pay

particular attention to the following obstacles: • Wires, fences, ropes, etc. • Cotton, snow and other materials that absorb radio waves • Sharply-angled objects • Low obstacles • Tall obstacles with upper sections projecting outwards in the direction

of your vehicle

• A person near the vehicle (depending on the type of clothes worn) • When the bumper is damaged.

■Certification (Canada only)

This ISM device complies with Canadian ICES-001.

CAUTION

■Caution when using the intuitive parking assist

Observe the following precautions. Failure to do so may result in the vehicle being unable to be driven safely and possibly cause an accident. ●Do not use the sensor at speeds in excess of 6 mph (10 km/h). ●Do not attach any accessories within the sensor range.

NOTICE

■Notes when washing the vehicle

Do not apply intensive bursts of water or steam to the sensor area. Doing so may result in the sensor malfunctioning.

157

2-4. Using other driving systems Rear view monitor system (vehicles with auto anti-glare inside rear view mirror)

The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.

The rear view image is dis- played on the inside rear view mirror when the shift lever is in the R.

The screen is turned off if any one of the following conditions are met: • The shift lever is shifted out

of R

• The back door opens • The screen remains on for 5

minutes

Automatic transmission Manual transmission Screen

■The rear view monitor system can be operated when

The shift lever is in R, the back door is fully closed and the engine switch is ON.

158

2

2-4. Using other driving systems

■Switching the screen ON/OFF mode

■Displayed area

Corners of bumper

When the screen is displayed, press the AUTO button on the inside rear view mir- ror to switch the screen ON/OFF mode. Screen ON mode: Green indicator comes on. Screen OFF mode: Orange comes on.

indicator

The auto anti-glare inside rear view mir- ror will revert to the screen ON mode each time the engine switch is turned on.

The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or underneath the spare tire cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.

159

2-4. Using other driving systems

■Rear view monitor system camera

In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly.

●The vehicle is in a dark area, such

as at night.

●The temperature near the lens is

extremely high or low.

●Water droplets are on the camera lens or humidity is high, such as when it rains.

●Foreign matter, such as snow or

mud, adheres to the camera lens.

●The sun or headlights are shining

directly into the camera lens.

●A bright object such as a white wall is reflected in the mirror surface over the monitor.

If a bright light, such as sunlight reflected off the vehicle body, is picked up by the camera, a smear effect* char- acteristic to the camera may occur. *: Smear effect: A phenomenon that occurs when a bright light is picked up by the camera; when transmitted by light source appears to have a vertical streak above and below it.

the camera,

the

■Smear effect

160

2-4. Using other driving systems

CAUTION

■When using the rear view monitor system, observe the following pre- cautions to avoid an accident that could result in death or serious inju- ries. ●Never depend solely on the monitor system when reversing. ●Always check visually and with the mirrors to confirm your intended path is

clear.

●Depicted distances between objects and flat surfaces differ from actual

distances.

■Conditions which may affect the rear view monitor system

●If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer.

●Rapid temperature changes, such as when hot water is poured on the

vehicle in cold weather, may cause the system to function abnormally.

●If the camera lens is dirty, it cannot transmit a clear image. Rinse with water and wipe with a soft cloth. If extremely dirty, wash with a mild cleanser and rinse.

●The displayed image may be darker and moving images may be slightly

distorted when the system is cold.

NOTICE

●As the camera has a water proof construction, do not detach, disassemble

or modify it. This may cause incorrect operation.

●If the camera lens becomes dirty, it cannot transmit a clear image. If water droplets, snow, or mud adhere to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse.

161

2-4. Using other driving systems Four-wheel drive system (4WD models with a manual transmission)

Use the four-wheel drive control lever to select the following transfer modes.

The center differential lock indicator comes on when the LL or HL mode is selected.

H (high speed position) Normal driving. HL (high speed position, center differential locked) When your vehicle’s wheel gets stuck in ditch or when you are driving on a slippy or bumpy surface. N (neutral position) No power is delivered to the wheels. LL (low speed position, center differential locked) Driving requiring maximum power and traction such as climbing or descending steep hills, off-road driving and hard pulling in sand or mud, etc.

162

2

2-4. Using other driving systems

■Shifting between H and HL

●You need not to depress the clutch pedal. ●If the center differential lock indicator does not come on when you shift

from H to HL, drive straight ahead while accelerating or decelerating.

●If the center differential lock indicator does not go off when you shift from HL to H, drive straight ahead while accelerating or decelerating, or drive in reverse.

■Shifting from HL to LL

Stop the vehicle or reduce your speed to less than 5 mph (8 km/h). Depress the clutch pedal and move the four-wheel drive control lever.

■Shifting from LL to HL

Depress the clutch pedal and move the four-wheel drive control lever.

■Shifting to LL

VSC is automatically turned off.

NOTICE

■To prevent damage to the center differential

●For normal driving on dry and hard surface roads, unlock the center differ-

ential.

●Shift to H after the wheels are out of the ditch or off the slippery or bumpy

surface.

●Do not shift to any position when the vehicle is cornering or when its

wheels spinning freely off the ground.

■Shifting from H to HL while driving

Never operate the four-wheel drive control lever if the wheels are slipping. Stop the slipping or spinning before shifting.

163

2-4. Using other driving systems Four-wheel drive system (4WD models with an automatic transmission)

Use the front-wheel drive control lever to select the following trans- fer modes.

The four-wheel drive indicator comes on when the H4, N or L4 mode is selected.

H2 (high speed position, two-wheel drive) Normal driving. H4 (high speed position, four-wheel drive) Greater traction than two wheel drive. When you experience a loss of power, such as wheel slipping. N (neutral position) No power is delivered to the wheels. L4 (low speed position, four-wheel drive) Driving requiring maximum power and traction such as climbing or descending steep hills, off-road driving and hard pulling in sand or mud, etc.

164

2-4. Using other driving systems

■Shifting between H2 and H4

●Reduce your speed to less than 50 mph (80 km/h) and shift the front-

wheel drive control lever from H2 to H4. If you have trouble shifting in cold weather, reduce your speed or stop the vehicle.

●If the four-wheel drive indicator does not go off when you shift from H4 to H2, drive straight ahead while accelerating or decelerating, or drive in reverse.

■Shifting between H4 and L4

Stop the vehicle, shift the shift lever to N and shift the front-wheel drive con- trol lever.

■Shifting to L4

VSC is automatically turned off.

■Four-wheel drive usage frequency

You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front drive components are lubricated.

CAUTION

■Shift from H2 to H4 while driving

Never operate the front-wheel drive control lever if the wheels are slipping. Stop the slipping or spinning before shifting.

165

2-4. Using other driving systems Active traction control system∗

The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. ■ System operation

Vehicles with an automatic transmission: Stop the vehicle, shift the shift lever to N and shift the front- wheel drive control lever into L4. Vehicles with a manual transmission: Stop the vehicle or reduce your speed to less than 5 mph (8 km/h). Depress the clutch pedal and shift the four-wheel drive control lever into LL.

Press the A-TRAC switch to activate the system.

At this time, the active traction control system indicator will come on. To cancel the system, push the switch again.

When the active traction control system is operating

If all wheels spin, the slip indica- tor flashes to indicate that the active traction control system have been engaged.

166

∗: If equipped

2-4. Using other driving systems

■When the rear differential is locked (vehicles with the rear differential

lock system) The active traction control system is activated only when the vehicle speed is less than 4 mph (6 km/h).

■Sounds and vibrations caused by the active traction control system

●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in the system.

●Vibrations may be felt through the vehicle body and steering. It may

occur when the system is operating.

■If the brake system overheats

The system will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.)

CAUTION

■The active traction control system may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the active traction control system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

167

2-4. Using other driving systems AUTO LSD system (2WD models)

The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when wheel spinning occurs in a ditch or rough surface. ■ System operation The system is activated when driving at a speed under 62 mph (100 km/h).

Press the VSC OFF switch to turn on the system.

At this time, the AUTO LSD and VSC OFF indicators will come on. To turn off the system, push the switch again.

When the AUTO LSD system is operating

If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system have been controlled the spinning of the rear wheels.

168

2-4. Using other driving systems

■If the engine is turned off and restarted

The AUTO LSD system and the indicators are automatically turned off.

■Automatic VSC reactivation

If the AUTO LSD system is turned on and the vehicle speed decreases, the vehicle speed increases the VSC system will turn on and the VSC OFF indi- cator will turn off. Then, if the VSC system will turn off and the VSC OFF indi- cator will turn on.

■If the brake system overheats

The system will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.) The system will be automatically restored after a short time.

CAUTION

■To avoid an accident

●Do not use the AUTO LSD system in conditions other than the above.

A much greater steering effort and more careful cornering control will be required.

●Do not drive with the AUTO LSD system continuously turned on.

169

2-4. Using other driving systems Rear differential lock system∗

The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.

Press the RR DIFF LOCK switch to lock the rear differen- tial.

At this time, the rear differential lock indicator will blink. Wait a few seconds for the system to complete operation. After the rear differential is locked, the indicator will stop blinking and remain on. To unlock the rear differential, push the switch again.

Using the rear differential lock system

Automatic transmission

4WD models: Before using the rear differential lock system. Stop the vehicle, shift the shift lever to N and shift the front- wheel drive control lever into L4 to see if this is sufficient. If this has no effect, additionally use the rear differential lock system. Be sure to stop the wheels. Press the RR DIFF LOCK switch. Gently depress the accelerator pedal. After the rear differential is locked, the indicator will come on.

Unlock the rear differential as soon as the vehicle moves. To unlock the rear differential, push the switch again.

∗: If equipped

170

2

2-4. Using other driving systems

Manual transmission

Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 5 mph (8 km/h). Depress the clutch pedal and shift the four-wheel drive control lever into LL to see if this is sufficient. If this has no effect, additionally use the rear differential lock system. Be sure to stop the wheels. Depress the clutch pedal. Press the RR DIFF LOCK switch. Slowly release the clutch pedal. After the rear differential is locked, the indicator will come on.

Unlock the rear differential as soon as the vehicle moves. To unlock the rear differential, push the switch again.

■Locking the rear differential

●When the rear differential is locked, VSC is automatically turned off.

(The rear differential lock and VSC OFF indicators will come on.)

●The following systems do not operate when the rear differential is locked. It is normal operation for the ABS warning light, VSC OFF indicator and slip indicator to be on at this time. • ABS • Brake assist system • VSC • TRAC

■The rear differential lock is disengaged when

●Shift the four-wheel drive control lever to H or HL. (4WD models with a

manual transmission)

●Shift the front-wheel drive control lever to H2 or H4. (4WD models with

an automatic transmission)

Never forget to turn off the switch after using this feature.

■After unlocking the rear differential

Check that the indicator goes off.

171

2-4. Using other driving systems

CAUTION

■To avoid an accident

●Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or ragged surface. Large steering effort and careful cornering control will be required.

●Do not lock the rear differential until the wheels have stopped spinning.

Otherwise, the vehicle may move in an unexpected direction when the dif- ferential lock is engaged, resulting in an accident. This may also lead to possible damage to rear differential lock component parts.

●Do not drive over 5 mph (8 km/h) when the rear differential is locked. ●Do not keep driving with the RR DIFF LOCK switch on.

172

2-4. Using other driving systems Clutch start cancel switch (vehicles with a manual transmission)

The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting. Be sure to follow the starting procedure. (→P. 126)

Press the CLUTCH START CANCEL switch to cancel the clutch start system with the engine switch is turned to the ON position.

The indicator will come on when the clutch start system is canceled. The clutch start cancel switch turned off is automatically when is turned off.

the engine switch

■Clutch start system

The system is designed to keep the starter motor from operating if the clutch pedal is not depressed all the way down.

173

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake Assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the rear wheels (2WD models) or all wheels (4WD models) from spinning when starting the vehicle or accelerating on slippery roads.

When VSC/TRAC are operating

If the vehicle is in danger of slip- ping, or if the rear wheels (2WD models) or all wheels (4WD models) spin, the slip indicator flashes to indicate that VSC/ TRAC have been engaged.

A buzzer (intermittent) sounds to indicate that VSC is operating.

174

2-4. Using other driving systems

To disable TRAC and/or VSC (2WD models)

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC

Press the VSC OFF switch to turn off TRAC.

■ Turning off TRAC and VSC

indicator will

The AUTO LSD come on. Push the switch again to turn the system back on.

Press the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC and VSC.

The VSC OFF and TRAC OFF indicators will come on. Push the switch again to turn both systems back on.

175

2-4. Using other driving systems

To disable TRAC and/or VSC (H2 and H4 mode [automatic transmission] or H and HL mode [manual transmission] on 4WD models)

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC

■ Turning off TRAC and VSC

Press the VSC OFF switch to turn off TRAC.

The TRAC OFF indicator will come on. Push the switch again to turn the system back on.

Press and hold the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC and VSC.

The VSC OFF and TRAC OFF indicators will come on. Push the switch again to turn both systems back on.

■Automatic reactivation of TRAC and VSC

Turning the engine switch off after turning off the TRAC and VSC systems will automatically re-enable them.

■Automatic VSC reactivation (2WD models)

If only the TRAC system is turned off, VSC OFF and AUTO LSD indicators turn on. The VSC system will turn on when the vehicle speed increases.

176

2

2-4. Using other driving systems

■Automatic TRAC and VSC reactivation

If the TRAC and VSC systems are turned off, the systems will not turn on, even when vehicle speed increases.

■Sounds and vibrations caused by the ABS, TRAC, VSC and brake

assist system ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

■If the brake system overheats

TRAC will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driv- ing.)

CAUTION

■The ABS does not operate effectively when

●The limits of the gripping performance have been exceeded. ●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

■Stopping distance when the ABS is operating will exceed that of nor-

mal conditions The ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or roads with uneven roads

177

2-4. Using other driving systems

CAUTION

■When VSC is activated

The slip indicator flashes and a warning buzzer sounds. Always drive care- fully. Reckless driving may cause an accident. Exercise particular care when the indicator flashes and a buzzer sounds. ■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if TRAC is operating. Do not drive the vehicle in conditions where stability and power may be lost.

■Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the appro- priate tire pressure level. The ABS and VSC will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

178

2

2-5. Driving information Off-road precautions

This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications.

Off-road vehicle feature

● Specific design characteristics give it a higher center of gravity than ordinary passenger cars. This vehicle design feature causes this type of vehicle to be more likely to rollover. And, utility vehicles have a significantly higher rollover rate than other types of vehi- cles.

● An advantage of the higher ground clearance is a better view of the

road allowing you to anticipate problems.

● It is not designed for cornering at the same speeds as ordinary passenger cars any more than low-slung sports cars designed to perform satisfactorily under off-road conditions. Therefore, sharp turns at excessive speeds may cause rollover.

179

2-5. Driving information

CAUTION

■Off-road vehicle precautions

Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ●In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.

●Avoid sharp turns or abrupt maneuvers, if at all possible.

Failure to operate this vehicle correctly may result in loss of control or vehicle rollover causing death or serious injury.

●Loading cargo on the roof luggage carrier will make the center of the vehi- cle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly.

●Always slow down in gusty crosswinds. Because of its profile and higher center of gravity, your vehicle is more sensitive to side winds than an ordi- nary passenger car. Slowing down will allow you to have better control.

●When driving off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

●Do not drive horizontally across steep slopes. Driving straight up or straight down is preferred. Your vehicle (or any similar off-road vehicle) can tip over sideways much more easily than forward or backward.

180

2-5. Driving information

Off-road driving

When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are permit-

ted to travel.

● Respect private property. Get owner’s permission before entering

private property.

● Do not enter areas that are closed. Honor gates, barriers and signs

that restrict travel.

● Stay on established roads. When conditions are wet, driving tech- niques should be changed or travel delayed to prevent damage to roads.

■Additional information for off-road driving

For owners in U.S. mainland, Hawaii and Puerto Rico:

To obtain additional information pertaining to driving your vehicle off-road, consult the following organizations. ●State and Local Parks and Recreation Departments ●State Motor Vehicle Bureau ●Recreational Vehicle Clubs ●U.S. Forest Service and Bureau of Land Management

181

2-5. Driving information

CAUTION

■Off-road driving precautions

Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: ●Drive carefully when off the road. Do not take unnecessary risks by driving

in dangerous places.

●Do not grip the steering wheel spokes when driving off-road. A bad bump could jerk the wheel and injure your hands. Keep both hands and espe- cially your thumbs on the outside of the rim.

●Always check your brakes for effectiveness immediately after driving in

sand, mud, water or snow.

●After driving through tall grass, mud, rock, sand, rivers, etc., check that there is no grass, bush, paper, rags, stone, sand, etc. adhering or trapped on the underbody. Clear off any such matter from the underbody. If the vehicle is used with these materials trapped or adhering to the underbody, a breakdown or fire could occur.

●In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.

●When driving off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

182

2-5. Driving information

NOTICE

■To prevent the water damage

●Take all necessary safety measures to ensure that water damage to the

engine or other components does not occur.

●Water entering the engine air intake will cause severe engine damage. ●Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ulti- mately damage.

●Water can wash the grease from wheel bearings, causing rusting and pre- mature failure, and may also enter the differentials, transmission and transfer case, reducing the gear oil’s lubricating qualities.

■When you drive through water

If driving through water, such as when crossing shallow streams, first check the depth of the water and the bottom of the river bed for firmness. Drive slowly and avoid deep water.

■Inspection after off-road driving

●Sand and mud that has accumulated in brake drums and around brake discs may affect braking efficiency and may damage brake system compo- nents.

●Always perform a maintenance inspection after each day of off-road driv- ing that has taken you through rough terrain, sand, mud, or water. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

183

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the luggage compartment whenever

possible.

● Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) − (Total weight of occupants) Steps for Determining Correct Load Limit— (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

184

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 1130 lb. (510 kg), the available amount of cargo and luggage load capacity will be as follows: 1130 lb. − 366 lb. = 764 lb. (510 kg − 166 kg = 344 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

764 lb. − 388 lb. = 376 lb. (344 kg − 176 kg = 168 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

185

2-5. Driving information

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment. ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Instrument panel • Dashboard • Auxiliary box or tray that has no lid

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious injury, in the event of sudden braking, sudden swerv- ing or an accident.

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

186

2

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 1130 lb. (510 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity. ■ Towing capacity: 5000 lb. (2265 kg)

Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label.(→P. 313)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

187

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the rear tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window, scrape an outside rear view mirror surface or move a wiper or outside rear view mir- ror that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.

● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

188

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission) or to 1 or R (manual transmission) without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the rear tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

■Snow chain installation

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the rear tires only. Do not install tire chains on the

front tires.

●Install tire chains following the instructions provided in the accompanying

instructions.

189

2-5. Driving information

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified for your vehicle. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h) regardless of the type of

snow tires being used.

●Snow tires should be installed on all wheels. ●4WD models:

Do not mix tires of different makes, models, tread patterns or treadwear.

■Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking. ●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

190

2

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger-carrying vehicle, thus towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. ■ Weight limits

Confirm the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

■ Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum of the weights of the unloaded vehicle, driver, passengers, luggage, hitch, and the trailer tongue load. It also includes the weight of any special equipment installed on your vehicle.

■ Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

191

2-5. Driving information

■ Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum 500 lb. (227 kg) (Tongue load / Total trailer weight x 100 = 9 to 11%) The total trailer weight and tongue load can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

Total trailer weight Tongue load

Towing a trailer

Consult your Toyota dealer for further information about additional requirements such as a towing kits, etc.

Hitch and tow hitch receiver

■ Hitch

Trailer hitch assemblies have different weight capacities estab- lished by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maximum weight rating specified for the trailer hitch.

192

2

2-5. Driving information

Selecting trailer ball

Use the correct trailer ball for your application.

Connecting trailer lights

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers are stamped with the required trailer ball size. Shank length Protrudes beyond the bottom of the lock washer and nut at least 2 threads. Shank diameter Matches diameter size.

the ball mount hole

Use the wire harness stored in the rear end underbody.

193

2-5. Driving information

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (→P. 396) ●Trailer tires should be inflated according to the trailer manufacturer’s rec-

ommendation.

●All trailer lights work to be legal. ●Confirm all lights work each time you connect them. ●The trailer ball is set up at the proper height for the coupler on the trailer. ●Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

●Make sure the trailer cargo is securely loaded. ●Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. ■Break-in schedule

●Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bearings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km).

194

2

2-5. Driving information

CAUTION

■To avoid accident or injury

●The total trailer weight (trailer weight plus the weight of cargo) must not

exceed 5000 lb. (2265 kg)

●If a trailer and cargo weight over 2000 lb. (907 kg), use a sway control

device with sufficient capacity.

●The gross combined weight (sum of your vehicle weight plus its load and

the total trailer weight) must not exceed the following. 2WD models:

9200 lb. (4173 kg)

4WD models:

9500 lb. (4309 kg)

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

●Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

●The tow hitch receiver installed on your vehicle must never be used on

another vehicle.

■Hitches

●If you wish to install a trailer hitch, your Toyota dealer should be consulted. ●Use only a hitch that conforms to the total trailer weight requirement. ●Follow the directions supplied by the hitch manufacturer. ●Lubricate the hitch ball with a light coat of grease. ●Remove the trailer hitch whenever you are not towing a trailer to reduce the possibility of additional damage caused by the hitch if your vehicle is struck from behind.

195

2-5. Driving information

CAUTION

■When towing a trailer

●If the total trailer weight exceeds 1000 lb. (453 kg), trailer brakes are

required.

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

NOTICE

■When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

■Brakes

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations.

■Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

■Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

196

2

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. The three main causes of vehicle-trailer accidents are driver error, excessive speed and improper trailer loading. Keep these in mind when towing. ● Before starting out, check the trailer’s light and the vehicle-trailer

connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. Vehicles with a manual transmission, prevent excessive clutch slippage by keeping engine rpm low and not racing the engine. Always start out in first gear.

● Avoid jerky steering and sharp turns, and slow down before mak-

ing a turn.

197

2-5. Driving information

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

● Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● In order to maintain engine braking efficiency, do not use the trans- mission in D (automatic transmission) or 6 (manual transmission).

● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 382)

198

2

2-5. Driving information

● Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoidable, do so only after performing the following:

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into 1 or R (manual transmission) or P (automatic trans- mission) and turn off the engine.

● When restarting after parking on a slope:

With the transmission in P (automatic transmission) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake (also brake pedal on vehicles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

199

2-5. Driving information

CAUTION

■To avoid an accident

●Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

●Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

●Avoid holding the brake pedal down too long or too frequently. This could

cause the brakes to overheat and result in reduced braking efficiency.

200

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

201

2-5. Driving information

202

3-1. Using the air conditioning system and defogger Air conditioning system

Outside air or recirculated air mode switch

Air conditioning ON/OFF switch

Fan speed control dial

Temperature control dial

Air outlet selection dial

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

A/C

is not pressed, the system will blow ambient temperature air or

If heated air. For quick cooling, turn the temperature control dial to the MAX A/C position. The air conditioning will automatically turn on and the air intake selector will be set to recirculated air mode.

204

3-1. Using the air conditioning system and defogger

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Set the dial to OFF to turn the fan off.

■ Selecting the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment.

When the dial is set to flows to the upper body.

, air

When the dial is set to , air flows to the upper body and feet.

When the dial is set to mainly air flows to the feet.

205

3-1. Using the air conditioning system and defogger

When the dial is set to , air flows to the feet and the wind- shield defogger operates.

The air intake selector is automat- ically set to outside air mode. To return

the recirculated air

mode, press

When the dial is set to , air flows to the windshield and side windows to defog them.

The air intake selector is automat- ically set to outside air mode. In this position, the air intake selector cannot be changed to the recirculated air mode.

■ Switching between outside air and recirculated air modes

Press

The mode switches between

(outside air mode) and

(recirculated air mode) each time the switch is pressed.

206

3-1. Using the air conditioning system and defogger

■ If the ambient temperature drops while using the recirculated

air mode The air intake mode automatically changes from recirculated air mode to outside air mode after a few minutes. To cancel this function:

Press and hold

for longer than 2 seconds.

To reactivate this function: Turn the engine switch to the LOCK or ACC position.

Adjusting the position of the air outlets

Center outlets

Direct air flow to the left or right, up or down.

207

3-1. Using the air conditioning system and defogger

Right and left side outlets

Direct air flow to the left or right, up or down.

Opening and closing the right and left side outlets

Open the vent. Close the vent.

208

3-1. Using the air conditioning system and defogger

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■When outside air temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

A/C

is pressed.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature adjust- ment dial.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

CAUTION

■To prevent the windshield from fogging up

Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

209

3-1. Using the air conditioning system and defogger Rear window defogger

This feature is used to defog the rear window.

On/off

Press the button to turn on the rear window defogger. The indicator light will come on. The defogger will automatically turn off after 15 to 240 minutes. The operation time changes according to the ambient tem- perature and vehicle speed. Pressing the button again also turns the defogger off.

■The rear window defogger can be operated when

The engine switch is in the ON position.

NOTICE

■To prevent battery discharge

Turn the rear window defogger off when the engine is off.

210

3-2. Using the audio system Audio system types

Type A: CD player with external CD changer controller and AM/FM radio Type B: CD player with changer and AM/FM radio

Type A

Type B

211

3-2. Using the audio system

Title

Using the radio Using the CD player Playing back MP3 and WMA discs Optimal use of the audio system Operating the sub woofer Changing display color Using the AUX adapter Using the steering wheel audio switches

Page P. 214
P. 220
P. 227
P. 235
P. 238
P. 239
P. 240
P. 242

■Welcome function (type B only)

When you turn the engine switch to the ACC or ON position, “FJ CRUISER” will appear scrolling on the display. And then “FJammer” will appear for 6 seconds. While this function is operating, the display is illuminated with full intensity and the instrument panel light control dial is disabled. However, you can turn

off the display illumination by pushing the

■Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

212

3-2. Using the audio system

CAUTION

■For vehicles sold in U.S.A. and Canada

●Part 15 of the FCC Rules