Download PDF Manual

In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.


(g) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual. (h) “ABS” Warning Light Vehicles without vehicle stability control system— The light comes on with the ignition key turned to the “ON” position. If the anti− lock brake system works properly, the light turns off after a few seconds. There- after, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, but the brake system still operates con- ventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.


124


the


the systems malfunctions,


Vehicles with vehicle stability control system— The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system work properly, the light turns off after a few seconds. Thereafter, if either of light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, traction control system and the vehicle stability control system do not op- erate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden brake or braking on slippery road surfaces.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.


D The light comes on while you are driv-


ing.


A warning light turning on briefly during operation does not indicate a problem.


CAUTION


If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.


(i) Open Door Warning Light This light remains on until all the doors are completely closed.


light system monitors


(j) SRS Warning Light The indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after 6 seconds. This means the SRS airbags and seat belt preten- sioners are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system, “AIRBAG ON” indi- cator light, “AIRBAG OFF” indicator light, front passenger’s seat belt buckle switch, seat belt pretensioner assemblies, inflat- ors, warning light, interconnecting wiring and power sources. If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. D When the ignition key is turned to the “ON” position, the light does not come on or remains on for more than about 6 seconds.


D The light comes on while driving.


The SRS warning light and “AIRBAG OFF” indicator light will come on if there is a malfunction in the front passenger occu- pant classification system. (k) Low Windshield Washer Fluid Level


Warning Light


The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” on page 328 in Section 7−3.) (l) “VSC” Warning Light The light warns that there is a problem somewhere in the vehicle stability control system or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after about a few seconds. If the light comes on, the vehicle stability control system and traction control system do not work. However, as conventional braking operates when applied, there is no problem to continue your driving.


125


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


In the following cases, contact your Toyota dealer: D The light does not come on after the


ignition is turned to on.


D The light is left on after the ignition is


turned to on.


D The light comes on while driving. The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed. (m) Engine Oil Replacement Reminder


Light (for vehicles sold in U.S.A.)


This light acts as a reminder to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500
miles) after the engine oil replacement, this light illuminates for about 3 seconds and for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the dis- tance driven exceeds 8000 km (5000
miles), the light will come on after the ignition key turned to “ON” position. The light will remain on thereafter. 126


then flashes


is


If


the


If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. light comes on, replace it as soon as possible. The system must be reset after the en- gine oil replacement. Reset the system by the following procedure: 1. Turn the ignition key to the “ACC” or the odometer details, see trip meters” on


“LOCK” position with reading shown. (For “Odometer and page 117 in this Section.)


two


2. Turn the ignition key to the “ON” posi- tion while holding down the trip meter reset knob.


indicates


Hold down the knob for at least 5 sec- onds. The odometer “000000” and the light goes off. If the system fails to reset, the light will continue flashing. (n) Key Reminder Buzzer This buzzer acts as a reminder to remove the key when you open the driver’s door with “ACC” or “LOCK” position.


ignition key


the


the


in


light


SERVICE


CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.


and


The open door warning come on.


light should


3. Close the door.


The open door warning light should go off.


4. Turn the ignition key to “ON”, but do


not start the engine. All the service reminder indicators ex- cept the open door warning light should come on. The “ABS” and “VSC” warn- ing replacement “TRAC OFF” and slip indicator lights go off after a few seconds. The SRS warning light goes off after about 6
seconds.


lights, engine oil


If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


SECTION 1− 7


OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual transmission Traction control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle stability control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


128
129
133
135
137
139
140


127


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


CAUTION


For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.


NOTICE


leave the key


Do not in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.


“LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be put in the “P” position before pushing the key. Vehicles with engine immobilizer system— Once you remove the key, the engine im- mobilizer system is automatically set. (See “Engine immobilizer system” on page 15
in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently. If the automatic unlocking operation linked with the ignition switch is set, all doors are automatically unlocked when the igni- tion switch is turned from the “ON” posi- tion to the “ACC” or “LOCK” position. For details, see “—Automatic door locking and unlocking functions” on page 24 in Section 1−2.


Ignition switch


“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see page 248 in Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key.


the key


leave


in


128


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Automatic transmission


Lock release button To prevent misshifting


Selector lever


With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in “ON” position.)


Shift while holding the lock release button in.


Shift normally.


Overdrive switch


Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, engine starting and


key removal


R: Reverse N: Neutral D: Normal driving (with overdrive on) 3, 2: Stronger engine braking L: Maximum engine braking


129


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” on page 140 in this Section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” on page 249 in Section 3. The transmission must be in “P” or “N”.


2. With your foot holding down the brake


pedal, shift the selector lever to “D”.


When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.


temperature


low,


is


CAUTION


Never put your foot on the accelera- tor pedal while shifting.


3. Release the parking brake and brake the accelerator pedal


pedal. Depress slowly for smooth starting.


If the automatic locking operation linked with the shift position is set, all doors are automatically locked when the selector le- ver is moved out of the “P” position with the ignition switch is in the “ON” position and all the doors are closed. For details, see “—Automatic door locking and unlock- ing functions” on page 24 in Section 1−2. (d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to fourth gear.


2006 CAMRY from July ‘05 Prod. (OM33708U)


(b) Overdrive switch You can select either fourth gear (with overdrive off) or fifth gear (with overdrive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will be on automatically.


for better


130


’06Camry_U (L/O 0507)


D Shift into the “3” position. The trans- mission will downshift third gear when the vehicle speed drops down to or lower than the following speed, and stronger engine braking will be en- abled.


to


D Shift into the “L” position. The trans- mission will downshift first gear when the vehicle speed drops down to or lower than the following speed, and maximum engine braking will be en- abled.


to


2.4 L 4−cylinder (2AZ−FE) engine


. . . . . . . . . . . . . . .


137 km/h (85 mph)


3.0 L V6 (1MZ−FE) engine


2.4 L 4−cylinder (2AZ−FE) engine


. . . . . . . . . . . . . . . .


45 km/h (28 mph)


3.0 L V6 (1MZ−FE) engine


. . . . . . . . . . . . . . .


136 km/h (85 mph)


. . . . . . . . . . . . . . . .


38 km/h (24 mph)


3.3 L V6 (3MZ−FE) engine


. . . . . . . . . . . . . . .


127 km/h (79 mph) D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than the following speed, and stronger engine braking will be en- abled.


3.3 L V6 (3MZ−FE) engine


. . . . . . . . . . . . . . . .


38 km/h (24 mph) Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled.


2.4 L 4−cylinder (2AZ−FE) engine


. . . . . . . . . . . . . . . .


87 km/h (54 mph)


3.0 L V6 (1MZ−FE) engine


. . . . . . . . . . . . . . . .


88 km/h (55 mph)


3.3 L V6 (3MZ−FE) engine


. . . . . . . . . . . . . . . .


82 km/h (51 mph)


For ways to decrease the vehicle speed, see “Cruise control” on page 140 in this Section.


CAUTION


Be careful when downshifting on a slippery shifting could cause the vehicle to skid or spin.


surface. Abrupt


(e) Using “3”, “2” and “L” positions The “3”, “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “3”, “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “3” or “2”, the vehicle will start in first gear and automat- ically shift to third gear or second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.


131


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


z Do not continue hill climbing or hard towing for a long time in the “3”, “2” or “L” position. This may cause severe automatic transmis- sion damage from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.


(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.


NOTICE


Never shift into reverse while the ve- hicle is moving.


(g) Parking 1. Bring the vehicle to a complete stop. 2. Pull the parking brake lever up fully to


securely apply the parking brake.


3. With


the brake pedal pressed down, shift the selector lever to the “P” posi- tion.


CAUTION


Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.


If the automatic unlocking operation linked with the shift position is set, all doors are automatically unlocked when the selector lever is moved to the “P” position with the ignition switch is in the “ON” position. For details, see “—Automatic door locking and unlocking functions” on page 24 in Section 1−2.


NOTICE


z Be careful not to over−rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference: 2.4 L 4−cylinder (2AZ−FE) engine—


“3” “2” “L”


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


142 km/h (88 mph) 91 km/h (57 mph) 50 km/h (31 mph)


3.0 L V6 (1MZ−FE) engine—


“3” “2” “L”


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


140 km/h (87 mph) 89 km/h (55 mph) 49 km/h (30 mph)


3.3 L V6 (3MZ−FE) engine—


“3” “2” “L”


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


133 km/h (82 mph) 85 km/h (53 mph) 47 km/h (29 mph)


132


2006 CAMRY from July ‘05 Prod. (OM33708U)


(h) Good driving practice D If the transmission repeatedly shifts up and down between fourth gear and ov- erdrive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately afterward.


D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.


CAUTION


Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.


NOTICE


Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.


’06Camry_U (L/O 0507)


Manual transmission


(i)


If you cannot shift the selector le- ver out of “P” position


If you cannot shift the selector lever from “P” position even though the brake pedal is depressed, use the shift lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” on page 284 in Section 4.


is conventional as


The shift pattern shown above. Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. Do not use the vehicle when stopped on an uphill grade—use the parking brake.


the clutch


to hold


133


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Maximum allowable speeds To get on a highway or to pass slower traffic, maximum acceleration may be nec- essary. Make sure you observe the follow- ing maximum allowable speeds in each gear:


gear


km/h (mph) (32) 52
(55) 89
137
(85) 189 (117)


NOTICE


Do not downshift faster speed for the next lower gear.


if you are going the maximum allowable


than


Recommended shifting speeds The transmission is fully synchronized and upshifting or downshifting is easy. For fuel economy and vehicle performance, you should upshift or downshift at the following speeds:


the best compromise between


gear


1 to 2 or 2 to 1
2 to 3 or 3 to 2
3 to 4 or 4 to 3
4 to 5 or 5 to 4


km/h (mph)


24 (15) 40 (25) 64 (40) 72 (45)


Downshift to the appropriate gear if accel- eration is needed when you are cruising below the above downshifting speeds. Upshifting too too soon or downshifting late will cause lugging, and possibly ping- ing. Regularly revving the engine to maxi- mum speed in each gear will cause ex- cessive engine wear and high fuel consumption.


134


Good driving practice D If it is difficult to shift into reverse, put the transmission in neutral, release the clutch pedal momentarily, and then try again.


D When towing a trailer, in order to main- tain engine braking efficiency, do not use fifth gear.


CAUTION


Be careful when downshifting on a slippery shifting could cause the vehicle to skid or spin.


surface. Abrupt


NOTICE


Make sure the vehicle is completely stopped before shifting into reverse.


2006 CAMRY from July ‘05 Prod. (OM33708U)


Traction control system The traction control system automatical- ly helps prevent the spinning of front wheels when the vehicle is started or accelerated on slippery road surfaces. When the ignition key is turned to “ON”, the system automatically turns on.


CAUTION


Under certain slippery road condi- tions, full traction of the vehicle and power against front wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tire chains. Always drive at an appropriate and cautious speed the present road condi- tions.


the vehicle


tires or


lose


for


to


’06Camry_U (L/O 0507)


When the traction control system is oper- ating, the following conditions occur: D The system controls the spinning of the front wheels. At this time, the slip indi- cator light blinks.


that


NORMAL DRIVING MODE Leave the system on during the ordi- nary driving so it can operate when needed. You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the trac- tion control system is in the self−check mode, but does not indicate a malfunction.


in


D You may feel vibration or noise in your the is


vehicle, caused by operation of brakes. This functioning properly.


the system


indicates


The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.


135


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


to “ON”.


“TRAC OFF” indicator light comes on for a few seconds when the ignition key is turned It will come on again when you push the “TRAC OFF” switch to turn off the system. In the following cases, contact your Toyota dealer: D The indicator light does not come on when the ignition key is turned “ON”. D The indicator light remains on after the


ignition is turned on.


D The indicator light comes on with the


normal driving mode while driving.


TRACTION CONTROL OFF MODE When getting the vehicle out of mud or newly fallen snow, etc., turn off the traction control system. This system that controls engine performance inter- feres with the process of freeing front wheels. To turn off: Push “TRAC OFF” switch. The “TRAC OFF” indicator light will come on. The vehicle stability control system is al- ways activated, even if the traction control system is turned off. To turn on: Push “TRAC OFF” switch once again. The “TRAC OFF” indicator light will go off. 136


“VSC” warning light This light warns that there is a problem somewhere in the traction control system or the vehicle stability control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the


ignition key is turned to “ON”.


D The warning light comes on while driv-


ing.


The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.


Vehicle stability control system The vehicle stability control system helps provide integrated control of the systems such as anti−lock brake sys- tem, traction control, engine control, etc. This system automatically controls the brakes and engine to help prevent the vehicle from skidding when corner- ing on a slippery road surface or oper- ating steering wheel abruptly. This system will activate when your ve- hicle speed reaches or exceeds 15 km/h (9 mph), and will deactivate when the ve- hicle speed reduces to below 15 km/h (9
mph). You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the sys- tem is in the self−check mode, but does not indicate a malfunction.


in


CAUTION


D Do not rely excessively on the ve- hicle stability control system. Even if the vehicle stability control sys- tem is operating, you must always drive carefully and attentively to avoid serious injury. Reckless driv- ing will result in an unexpected ac- cident. light flashes, an alarm sounds, and spe- cial care should be taken while driving.


indicator


the slip


If


D Only use tires of specified size. The size, manufacture, brand and tread pattern for all 4 tires should be the same. If you use the tires other than specified, or different type or size, the vehicle stability control system may not function correctly. When replacing the tires or wheels, contact your Toyota dealer. (See “Checking and replacing tires” on page 317 in Section 7−2.)


D In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tires or tire chains.


137


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the


ignition key is turned to “ON”.


D The warning light comes on while driv-


ing.


The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.


If the vehicle is going to skid during driv- ing, the slip indicator light blinks and an alarm sounds intermittently. Special care should be taken while driving. The slip indicator light comes on for a few seconds when the ignition key is turned to “ON”. If the indicator light does not come on when the ignition is turned on, contact your Toyota dealer.


“VSC” warning light This light warns that there is a problem somewhere in the vehicle stability control system or the traction control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.


138


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Parking brake


Lever type (type A)


Pedal type (type A)


Lever type (type B)


Pedal type (type B)


it while setting


When parking, firmly apply the parking brake to avoid inadvertent creeping. Lever type— To set: Pull up the lever. For better hold- ing power, first depress the brake pedal and hold the parking brake. To release: Pull up the lever slightly (1), press the lock release button (2), and low- er (3). Pedal type— To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal while depressing the brake pedal. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.


the parking brake


CAUTION


Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.


139


2006 CAMRY from July ‘05 Prod. (OM33708U)


Cruise control The cruise control is designed to main- tain a set cruising speed without requir- ing the driver to operate the accelera- tor. Cruising speed can be set to any speed above 40 km/h (25 mph). Within the limits of the engine’s capabili- ties, cruising speed can be maintained up or down grades. However, changes in ve- hicle speed may occur on steeper grades.


CAUTION


D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.


If


D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.


140


’06Camry_U (L/O 0507)


CAUTION


To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off.


TURNING THE SYSTEM ON AND OFF To turn the cruise control on, press the “ON−OFF” button. The “CRUISE” indicator light on the instrument panel will come on to indicate that the cruise control is opera- tional. Pressing “ON−OFF” button again turns the system off. When the system is turned off, cruising speed must be reset when the cruise con- trol is turned on again.


the


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration.


CAUTION


For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overrev- ving.


SETTING THE CRUISING SPEED On vehicles with automatic transmission, the transmission must be in “D” before you set the cruising speed. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed. If the speed is not satisfac- tory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6 km/h (1.0 mph). You can now take your foot off the accelerator pedal.


CANCELLING THE CRUISE CONTROL The cruise control may be temporarily cancelled by the driver or by the system itself under certain circumstances. Tempo- rary cancellation allows the set cruising speed to remain in memory. The cruise control can be temporarily can- celled by doing the following: D Pulling the lever in the “CANCEL” di-


rection and releasing it


D Depressing the brake pedal D Depressing


the clutch pedal (manual


transmission)


Under certain circumstances, control is temporarily cancelled: D When vehicle speed


falls below 40


the cruise


km/h (25 mph)


D When vehicle stability control is acti-


vated


is cancelled and


When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con- trol the set speed is erased from memory. The “CRUISE” indicator light remains on to indicate that the system is still in op- eration.


141


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “− SET” direction. On vehicles with automatic transmission, even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled.


If you use


sure


button. Make


To turn the cruise control off, press the “ON−OFF” the “CRUISE” indicator light is off. If the cruise control automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESUMING THE CRUISE CONTROL If the cruise control is temporarily can- celled, the cruising speed can be resumed by pushing the lever up in the “+ RES” direction. Vehicle speed must be above 40 km/h (25
mph). RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction.


the


light


indicator


“CRUISE”


CRUISE CONTROL FAILURE WARNING If flashes when using the cruise control, press the “ON−OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The


light goes out after


indicator


it


comes on.


If this is the case, contact your Toyota dealer and have your vehicle inspected.


142


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


SECTION 1− 8


OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference Using your audio system Audio remote controls Audio system operating hints


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


144
145
168
170


For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”.


143


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Reference


Type 1: AM·FM radio/compact disc player (with compact disc changer controller)


Type 2: AM·FM radio/cassette player/com- pact disc player (with compact disc changer controller)


Type 3: AM·FM radio/cassette player/com- pact disc player with changer (with XM satellite radio∗ controller)


∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.


144


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “FM1”, “FM2”, “FM1·2”, “FM”, “SAT”∗, “TAPE”, “CD” or “DISC” to turn on that function without pushing “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. function was pre- viously playing, it will come on again. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.


If another


SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1”, “FM2”, “FM1·2”, “FM”, “SAT”∗, “TAPE”, “CD” or “DISC” if the sys- tem is already on but you want to switch from one function to another. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.


LISTENING TO THE XM SATELLITE RADIO BROADCAST∗ (type 3) To listen to a satellite radio broadcast in your vehicle, an additional genuine Toyota satellite receiver and antenna (or equiva- lents) must be purchased and installed. A subscription to the XM satellite radio ser- vice is also necessary. How to subscribe to an XM satellite radio An XM satellite radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 contiguous states.


radio, visit XM on


How to subscribe: You must enter into a separate service agreement with the XM radio in order to receive satellite broadcast programming in the vehicle. Additional activation and ser- vice subscription fees apply that are not included in the purchase price of the ve- hicle and optional digital satellite tuner. For complete information on subscription rates and terms, or to subscribe to the XM the web at www.xmradio.com or call an XM’s Listener Care at (800) 852−9696. The XM radio is solely responsible for the quality, availabil- ity and content of the satellite radio ser- vices provided, which are subject to the terms and conditions of the XM radio cus- tomer service agreement. Customers should have ID ready; the radio ID can be found by tun- ing to “channel 000” on the radio. For details, see “Displaying the radio ID” be- low. All fees and programming are the respon- sibility of the XM satellite radio and are subject to change.


radio


their


145


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange (type 2 and 3), and bass levels. In fact, different kinds of mu- sic and vocal programs usually sound bet- ter with different mixes of treble, mi- drange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.


YOUR RADIO ANTENNA Your vehicle has an antenna printed on the inside of the rear window.


NOTICE


Putting a film (especially a conductive or metallic film) on the rear window will noticeably reduce the sensitivity of the radio.


YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.


NOTICE


Never try to disassemble or oil any part of the cassette player. Do not insert anything other than cassette tapes into the slot.


Satellite tuner technology notice: Toyota’s satellite radio tuners are awarded Type Approval Certificates from XM Satel- lite Radio Inc. on “March 10, 2003” and “April 15, 2003” as proof of compatibility with the services offered by the XM satel- lite radio. Displaying the radio ID Each XM tuner is identified with a unique radio ID. You will need the radio ID when activating XM service or when reporting a problem. If you select the “TUNE” knob, the ID code of 8 alphanu- meric characters appears. If you select another channel, display of the ID code is canceled. The channel (000) alternates the display between the radio ID and the spe- cific radio ID code. ∗: Use of satellite radio requires XM tuner and service. Contact your Toyota deal- er for details.


“CH 000” using


the


146


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


YOUR COMPACT DISC PLAYER (type 1
and 2) When you insert a disc, gently push it in with the label side up. The compact disc player will play from track 1 through to the end of the disc. Then it will play from track 1 again. The player is intended for use with 12 cm (4.7 in.) discs only.


NOTICE


Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.


YOUR COMPACT DISC PLAYER WITH CHANGER (type 3) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. The compact disc player will play from track 1 through to the end of the disc. Then it will play from track 1 of the next disc. The player is intended for use with 12 cm (4.7 in.) discs only.


NOTICE


z Do not stack up two discs for in- sertion, or it will cause damage to the compact disc player. Insert only one compact disc into slot at a time.


z Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.


147


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


—Controls and features "Type 1


Details of specific buttons, controls and features are described in the alphabetical list that follows.


148


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


(See


to preset and


1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM”, “FM1” or “FM2” button.)


(Eject button)


the compact disc eject button


Push eject a compact disc. While the ignition is in “LOCK”, you can eject a disc but you cannot reinsert it.


to


(Reverse/Fast−forward button)


time


Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast−forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BASS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TREBLE: Adjusts high−pitched tones. The display ranges from −5 to 5. BALANCE: Adjusts the sound balance be- tween left speakers. The display ranges from L7 to R7. the sound balance be- FADER: Adjusts tween the front and rear speakers. The display ranges from F7 to R7.


tone and balance,


the right and


turn


you


the


the


DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “Err 1”: The disc may be dirty, damaged or (up−side down). Clean the disc and re−insert it. “Err 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “Err 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer.


incorrectly


inserted


149


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


in random order, or


RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.


feature, push


random


Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. FM1 FM2
Push the “FM1” or “FM2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume.


150


the


track


RPT (Repeat) There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan all the frequencies: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push “Ɯ” or “Ɲ” side of this button again. To scan the preset stations: Push and hold “Ɯ” or “Ɲ” side of the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5
seconds, and then move to the next pre- set station. To stop scanning, push “Ɯ” or “Ɲ” side of this button again.


Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. To stop scanning, push “Ɯ” or “Ɲ” side of this button again. If the player scanned all it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push and hold “Ɯ” or “Ɲ” side of the “SCAN” button until you hear a beep. ·SCAN” will appear on the display and “ the player will scan the first track on the next disc. To stop scanning, push “Ɯ” or “Ɲ” side of this button again. If the player has scanned all it will stop scanning.


the tracks on the disc,


the discs,


the seek mode,


(Seeking/Tracking up or


the radio finds and the next station up or down the


SEEK/TRACK down) Radio In plays station band. To seek the next station, quickly push and release “Ɯ” or “Ɲ” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “Ɯ” or “Ɲ” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time.


151


2006 CAMRY from July ‘05 Prod. (OM33708U)


ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.


152


’06Camry_U (L/O 0507)


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


"Type 2


Details of specific buttons, controls and features are described in the alphabetical list that follows.


153


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


(See


to preset and


the button until


1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK/TRACK” button.) Push and hold down you hear a beep—this will set the station to the but- ton. The button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM1·2” button.)


(Eject button) the cassette


Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. While the ignition is in “LOCK”, you can eject a cassette or disc but you cannot reinsert it.


154


(Program)



indicates


Push “ ” (preset button 5) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates bottom side). Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.


feature: After


top side, “


(Reverse/Fast−forward


but-


tons) Cassette player


Push “ ” (preset button 2) to fast−for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 1) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast−forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button.


If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast−forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. Compact disc player


” (preset button 2) or Push and hold “ “ ” (preset button 1) to fast−forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. CD (Compact disc) Push the “CD” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


inserted


incorrectly


too. Allow


the player


Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be to cool down. “Err 1”: The disc may be dirty, damaged or (up−side down). Clean the disc and re−insert it. “Err 3”: There is trouble inside the sys- tem. Eject the disc. Set the disc again. “Err 4”: Over−current. Ask your Toyota dealer to inspect. If the malfunction still exists, take your vehicle to your Toyota dealer. Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 5) or “Ɯ” (preset button 6) until the number of the disc you want to listen appears on the display.


B NR∗


” (preset button 6). “


Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push “ ” will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button.


the


MODE (Tone and sound balance adjust- ment function) Each time you push the “MODE” knob, the mode changes. To adjust tone and balance, turn the knob. BASS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TREBLE: Adjusts high−pitched tones. The display ranges from −5 to 5. BALANCE: Adjusts the sound balance be- tween left speakers. The display ranges from L7 to R7. FADER: Adjusts the sound balance be- tween the front and rear speakers. The display ranges from F7 to R7. PWR·VOL (Power and Volume) Push turn to audio system on and off. Turn “PWR·VOL” knob to adjust the volume.


the “PWR·VOL” knob


the right and


the the


155


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


RPT (Repeat) Cassette player Push “RPT” (preset button 3) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically be rewound and replayed. To turn off the repeat feature, push this but- ton again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact disc player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 3) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again.


track


the


in random order, or


” will appear on the player will perform


RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset the button 4). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 4) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.


feature, push


random


156


With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 3) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To select a station, push “SCAN” button again.


2006 CAMRY from July ‘05 Prod. (OM33708U)


’06Camry_U (L/O 0507)


To scan all the frequencies: Quickly push and release the “SCAN” but- ton. If you hear a beep, you held the button too long, and the radio will scan the preset stations. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again. To select a station, push “SCAN” button again. Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display

Loading...
x