with a rear seat as it may cause the “AIRBAG OFF” indicator light be il- luminated. If the seatback interferes with the rear seat, return the seat- back to a position where it does not interfere with the rear seat. Keep the front passenger seatback as upright as possible when the ve- hicle is moving. Reclining the seat- back excessively may lessen the ef- fectiveness of the seat belt system.
D Make
the
the
sure
If light
reconnect
passenger
seat. indicator
“AIRBAG ON” indicator light is illuminated when using the seat belt extender for the the front “AIRBAG OFF” is illuminated, disconnect the extender tongue from the seat belt buckle, then seat belt. Reconnect the seat belt extender after making sure the “AIRBAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIRBAG OFF” is illuminated, front passenger the airbag and side airbag on the front passenger side may not activate correctly, which could cause death or serious in the event of collision.
indicator
injury
light
D If an adult sits
If
is
in
the
the
light
light should be
front passenger seat, the “AIRBAG ON” indicator illumi- “AIRBAG OFF” nated. indicator illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. the “AIRBAG OFF” indicator light still remains illumi- nated, either ask the passenger to move to the rear seat, or if that is not front the passenger seat fully rearward.
possible, move
If
the
D Wear the seat belt properly. D Make sure
front passenger’s seat belt tab has not been left in- serted into the buckle before some- one sits front passenger seat.
the
in
D Do not apply a heavy load to the front passenger seat or equipment (e.g. seatback pocket).
75
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
D Do not remove the seat. D Do not kick
the
front passenger seat or subject it to severe impact. Otherwise, the SRS warning light may come on to indicate a malfunc- tion of the detection system. In this case, contact your Toyota dealer im- mediately.
The “AIRBAG ON” indicator light may be
illuminated (the front passenger airbag and
side airbag on the front passenger seat
may deploy) even if observing the above
cautions, when a child sits in, or a for-
ward−facing
is
installed on the front passenger seat. Re-
fer to all the cautions in “SRS airbags” on
page 58 and “Child restraint” on page 76
in this Section.
restraint
system
child
D Do not put weight on the front pas- senger seat by putting your hands or feet on the front passenger seat seatback from the rear passenger seat.
D Do not let a rear passenger lift the front passenger seat with their feet or press on the seatback with their legs.
D Do not put objects under the front
passenger seat.
D Child restraint systems installed on the rear seat should not contact the front seatbacks.
D When it is unavoidable to install the forward−facing child restraint sys- tem on the front passenger seat, install the child restraint system on the the proper order. (As for the installation order, see “—Child restraint sys- tem” on page 78 in this Section.)
front passenger seat
in
76
Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- propriate child restraint systems for children. The laws of all 50 states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” on page 47 in this Section for details.
CAUTION
D For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior.
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
D Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, installed on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or serious if the rear−facing child restraint system is installed on front passenger seat.
injury to the child
the
the
D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.
force. Otherwise,
inflate with
D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbags and/or curtain shield air- bags inflate, and the impact could cause death or serious injury to the child.
If
installing a child
D Do not use the seat belt extender when restraint system on the front or rear passen- ger seat. installing a child re- straint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of collision.
D Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly se- cured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sud- den stop or accident.
77
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 89 in this Section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 91 in this Sec- tion.
(A) Infant seat
—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s in- structions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. restraint system should be The child installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than the passenger compartment. This will pre- vent the event of a sudden stop or accident.
injuring passengers
from
in
it
78
(B) Convertible seat
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
—Installation with seat belt
(C) Booster seat
(A) INFANT SEAT INSTALLATION An infant seat must be used in rear− facing position only.
CAUTION
D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the impact of the rapid inflation of the front pas- senger airbag could cause death or serious if the rear−facing child restraint system is installed on front passenger seat.
injury to the child
the
79
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
CAUTION
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
2006 CAMRY from July ‘05 Prod. (OM33708U)
the
lock mechanism of
D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.
80
’06Camry_U (L/O 0507)
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
the
To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing the infant seat
firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
81
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the appropriate age and size of the child as well as directions the child restraint system.
installing, follow instructions about
installing
for
4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
82
Install the child restraint system on the front passenger seat only when it is un- avoidable. Your vehicle is equipped with a front passenger occupant classification system. In order to activate the occupant classification system correctly, install the forward−facing child restraint system on the front passenger seat in the following order: 1. Turn the ignition key to the “ON” posi-
tion.
2. Move the front passenger seat to the
rearward position.
3. Put the child restraint system on the front passenger seat without putting your weight on front passenger seat.
the
4. Insert the seat belt tab into the seat
belt buckle.
5. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the seat securely, make sure the belt is in the lock mode before letting the belt retract.
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
6. While pressing
the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
7. Put a child on the child restraint sys- tem and secure the child, complying with the instructions provided by the child restraint system manufacturer.
light
indicator
illuminated when the ignition key
The “AIRBAG OFF” indicator light should be is “ON” and the child is in the child restraint system after following these procedures. The “AIRBAG OFF” indi- cates the SRS front passenger airbag and side airbag on the passenger side will not deploy. If the “AIRBAG ON” indicator light is illuminated, remove the child restraint system and reinstall it with the ignition key in the “ACC” or “LOCK” position. If the “AIRBAG ON” indicator light is illumi- nated when the ignition key is turned to the “ON” position, then the SRS front pas- senger airbag and side airbag on the pas- senger side may deploy in an accident. Do not drive the vehicle in this condition. Remove the child restraint system and contact your Toyota dealer.
CAUTION
the
D Never install a rear−facing child re- straint system on the front passen- ger seat. A forward−facing child re- straint system should only be installed on front passenger seat when unavoidable. If you must install the child restraint system on the front passenger seat, put the seat in its most rearward position, and install the forward−facing child restraint system in the proper or- der. Otherwise, the front passenger occupant classification system can not detect the presence of the child restraint system and the front pas- senger airbag and side airbag on the front passenger seat could deploy, and the impact could cause death or serious injury to the child.
83
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and/or curtain shield airbag inflate, and the impact could cause death or serious injury to the child.
Move seat fully back
D Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the impact of the rapid inflation of the front pas- senger airbag could cause death or serious if the rear−facing child restraint system is installed on front passenger seat.
injury to the child
the
the
D A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag could considerable speed and the child may be killed or seriously in- jured.
force. Otherwise,
inflate with
84
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
provided insert the
by tab
the
lock mechanism of
D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
D If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.
CAUTION
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
85
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing
the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
86
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.
Move seat fully back
CAUTION
the
D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.
force. Otherwise,
inflate with
87
2006 CAMRY from July ‘05 Prod. (OM33708U)
D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in a child restraint system. It is dangerous if the side airbag and/or curtain shield airbag inflate, and the impact could cause death or serious injury to the child.
88
’06Camry_U (L/O 0507)
CAUTION
D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.
1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.
Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 47 in this Section for details.
could
D Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.
injuries due
D For child’s safety, do not place the
shoulder belt under child’s arm.
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
—Using a top strap
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
D If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
2. To remove the booster seat, press the the
buckle release button and allow belt to retract.
Follow the procedure below for a child restraint system that requires the use of a top strap.
89
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Symbol
Anchor brackets
Use the anchor bracket on the package tray behind the rear seat to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the locations of the anchor brackets.
for each
installed
TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.
2. Open the lid of the anchor bracket.
90
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
—Installation with child restraint lower anchorages
4. Replace the head restraint and lift it
up to the uppermost lock position.
specifications
Lower anchorages for the child restraint
systems interfaced with the FMVSS225
or CMVSS210.2
are
installed in the rear seat.
The anchorages are installed in the clear-
ance between the seat cushion and seat-
back of both outside rear seats.
Child restraint systems interfaced with the
FMVSS213 or CMVSS213 specification
can be fixed with these anchorages. In
this case, it is not necessary to fix the
child restraint system with a seat belt on
the vehicle.
91
2006 CAMRY from July ‘05 Prod. (OM33708U)
3. Fix the child restraint system with
the seat belt. Latch bracket and tighten the top strap.
the hook onto
the anchor
instructions
For the child re- straint system, see “Child restraint” on page 76 in this Section.
install
to
CAUTION
Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.
’06Camry_U (L/O 0507)
RESTRAINT
SYSTEM
CHILD INSTALLATION 1. Widen
the gap between
the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.
the button on
2. Type A—Latch the hooks of
lower the anchorages and
straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.
Canada only
Type A
92
Canada only
Type B
For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 89 in this Section.)
it should be anchored. (For
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
For installation details, refer to the instruc- tion manual equipped with each product.
CAUTION
D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.
D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.
it
the
lock mechanism of
D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
93
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
94
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
SECTION 1− 5
OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Ignition switch light Personal lights Windshield wipers and washer Rear window and outside rear view mirror defoggers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
109
110
110
110
111
112
112
113
103
2006 CAMRY from July ‘05 Prod. (OM33708U)
Headlights and turn signals (for the U.S.A.)
’06Camry_U (L/O 0507)
Automatic operation—
To turn on or off the lights automatical-
ly, twist the headlight/turn signal lever
knob to the “AUTO” position when the
ignition key is in the “ON” position.
The headlights and/or all of the lights in
position 1 automatically turn on or off de-
pending on the darkness of the surround-
ings.
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.
HEADLIGHTS Manual operation— To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The headlight light (green light) on the instrument panel will tell you that the low beams are on.
license plate,
low beam
indicator
tail,
the
top of
the driver’s side
The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor.
104
2006 CAMRY from July ‘05 Prod. (OM33708U)
Automatic light cut off system
Position 1 or “AUTO” position with the
tail lights on—
The lights automatically turn off when the
driver’s door is opened with the ignition
key in the “ACC” or “LOCK” position.
Position 2 or “AUTO” position with the
headlights on—
The lights automatically turn off after 30
seconds when any of the doors or trunk
lid is opened and closed with the ignition
key in the “ACC” or “LOCK” position.
With wireless remote control—If you want
to turn off the lights immediately, push the
“LOCK” button on
remote
control transmitter twice. The lights also
can be turned off immediately by pushing
the “LOCK” button on the wireless remote
control
the doors
locked and the trunk lid closed.
If any of the doors or trunk lid is kept
open, the lights automatically turn off after
20 minutes.
To turn on the lights again, turn the igni-
tion key to the “ON” position or actuate
the headlight switch. If you are going to
park for over one week, make sure the
light switch is in the “DRL OFF” position.
transmitter with all
the wireless
’06Camry_U (L/O 0507)
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
Daytime Running Light (DRL) system The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The ignition is on with the engine run-
ning.
D The light switch is in the “AUTO” posi-
tion or position 1.
D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to position 1. Twist the knob to position 2 to turn the headlights to full intensity for night driving. To turn off the DRL system, twist the knob to the position 3 (“DRL OFF”) or turn the ignition switch off.
105
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Headlights and turn signals (for Canada)
High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights even when the headlights are off.
the lever all
106
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 328 in Section 7−3.
tail,
license plate,
HEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1—Parking,
side marker and instrument panel lights
The tail light indicator (green light) on the
instrument panel will tell you that the tail
lights are on.
Position 2—Headlights and all of
above
Position 3 (“AUTO”)—Headlights and/or all
of the lights in the position 1
They automatically turn on or off depend-
ing on the darkness of the surroundings.
the
2006 CAMRY from July ‘05 Prod. (OM33708U)
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.
’06Camry_U (L/O 0507)
top of
the driver’s side
The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. If you feel that the automatic light control comes into operation too early or too late, have the sensor adjusted by your Toyota dealer.
Automatic light cut off system
Position 1 or position 3 with the tail
lights on—
The lights automatically turn off when the
driver’s door is opened with the ignition
key in the “ACC” or “LOCK” position.
Position 2 or position 3 with the head-
lights on—
The lights automatically turn off after 30
seconds when any of the doors or trunk
lid is opened and closed with the ignition
key in the “ACC” or “LOCK” position.
If you want to turn off the lights immedi-
ately, push the “LOCK” button on the wire-
less remote control transmitter twice. The
lights also can be turned off immediately
by pushing the “LOCK” button on the wire-
less remote control transmitter with all the
doors locked and the trunk lid closed.
If any of the doors or trunk lid is kept
open, the lights automatically turn off after
20 minutes.
To turn on the lights again, turn the igni-
tion key to the “ON” position or actuate
the headlight switch. If you are going to
park for over one week, make sure the
light switch is in the “OFF” position.
107
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
Daytime Running Light (DRL) system The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The ignition is on with the engine run-
ning.
is
D The knob
“OFF” position, position 1 or position 3 with tail lights on.
the
in
D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to position 1. Twist the knob to position 2 to turn the headlights to full intensity for night driving.
108
High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.
the lever all
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Emergency flashers
NOTICE
To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 328 in Section 7−3.
flashers,
turn on
the emergency
To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.
109
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Instrument panel light control
Front fog lights
Interior light
To adjust the brightness of the instru- ment panel lights, turn the dial. With the dial turned fully up, the intensity of the instrument panel lights will not be reduced even when the tail lights/head- lights are turned on.
To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.
To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns light on when any door is opened. The light goes off when all the doors are closed.
the
110
2006 CAMRY from July ‘05 Prod. (OM33708U)
ILLUMINATED ENTRY SYSTEM When the switch is in the “DOOR” posi- tion and any door is opened, the light will come on. After all the doors are closed, the light remains on for about 15 seconds before fading out. However, in the following cases, the light go off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.
D The ignition key is turned to the “ACC” or “ON” position after all the side doors are closed.
D All the doors are closed and locked. When all the doors are unlocked using either the key or the wireless remote con- trol transmitter simultaneously, the interior light will come on and remain on for about 15 seconds before fading out. To prevent the battery being discharged, the light will automatically turn off when the key is removed and the door is left opened with the switch at the “DOOR” position for 20 minutes or more.
’06Camry_U (L/O 0507)
Ignition switch light
When all the doors are unlocked using either the key or the wireless remote con- trol transmitter simultaneously, the ignition switch light will come on and remain on for about 15 seconds before fading out. To prevent the battery being discharged, the light will automatically turn off when the key is removed and the door is left opened for 20 minutes or more.
For easy access to the ignition switch, the ignition switch light comes on when any of the doors are opened. The light remains on for about 15 seconds after all the doors are closed. However, in the following cases, the light goes off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.
D The ignition key is turned to the “ACC” or “ON” position after all the side doors are closed.
D All the doors are closed and locked.
111
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Personal lights
Windshield wipers and washer
To turn on the front personal lights, push the lenses. To turn the lights off, push the lenses once again.
To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.
Lever position
Speed setting
Position 1
Position 2
Position 3
Intermittent
Slow
Fast
For a single sweep of push the lever up and release it.
the windshield,
112
With interval adjuster: The “INT” band lets you adjust the wiping time interval when the wiper lever is in the intermittent posi- tion (position 1). Twist the band upward to increase the time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 328 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.
the washer
NOTICE
Do not operate the wipers if the wind- shield the glass.
It may scratch
is dry.
2006 CAMRY from July ‘05 Prod. (OM33708U)
When waxing your vehicle, make sure that the washer nozzles do not become blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the vehicle serviced.
NOTICE
If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.
’06Camry_U (L/O 0507)
Rear window and outside rear view mirror defoggers
With manual air conditioning controls
With automatic air conditioning controls
To defog or defrost the rear window,
push the switch.
The key must be in the “ON” position.
The thin heater wires on the inside of the
rear window will quickly clear
the sur-
faces. An indicator light will illuminate to
indicate the defogger is operating.
On some models, heater panels
in the
outside rear view mirrors will also quickly
clear the surfaces.
Push the switch once again to turn the
defogger off.
The system will automatically shut off af-
ter the defogger has operated about 15
minutes.
CAUTION
Since the mirror surfaces can get hot do not touch them when the defogger switch is on.
turn
Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow.
113
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.
NOTICE
When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.
114
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
SECTION 1− 6
OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers
116
116
117
117
119
115
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Fuel gauge
Engine coolant temperature gauge
Low fuel level warning light
On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
indicates
The gauge the approximate quantity of fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The gauge remains for about 10 minutes after the ignition switch is turned off. Turn the headlight switch off and then on to illuminate the instrument cluster. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible.
116
The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool.
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Tachometer
Odometer and two trip meters
Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high
speed driving.
D Idling for a long period with the air conditioning on in stop−and−go traffic.
D Towing a trailer.
NOTICE
z Do not remove the thermostat
in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.
z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 267 in Section 4.
The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.
NOTICE
Do not let the indicator needle get into the red zone. This may cause severe engine damage.
trip meters when
This meter displays the odometer and two ignition switch is on. 1. Odometer—Shows
total distance
the
the
the vehicle has been driven.
2. Two
trip meters—Show
two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.
fuel economy and
the other
117
2006 CAMRY from July ‘05 Prod. (OM33708U)
to
3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B. This display remains for about 10 minutes after the ignition switch is turned off. Turn the headlight switch off and then on to illuminate the instrument cluster.
118
’06Camry_U (L/O 0507)
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
Service reminder indicators and warning buzzers
If the indicator or buzzer comes on...
Do this.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
or
If parking brake is off, stop immediately and contact Toyota dealer.
(indicator and buzzer)
Fasten driver’s seat belt.
(indicator and buzzer)
Fasten front passenger’s seat belt.
Stop immediately and contact Toyota dealer.
Take vehicle to Toyota dealer.
Stop and check.
Low fuel level warning light
Fill up tank.
119
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
If the indicator or buzzer comes on...
Do this.
or
Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.
Close all doors.
Take vehicle to Toyota dealer immediately.
Add washer fluid.
Take vehicle to Toyota dealer.
Replace engine oil.
Key reminder buzzer
Remove key.
(h)
(i)
(j)
(k)
(l)
(m)
(n)
120
2006 CAMRY from July ‘05 Prod. (OM33708U)
(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. D When the brake fluid level is low...
ignition key
turned
the
is
CAUTION
It is dangerous to continue driving normally when the brake fluid level is low.
Have your vehicle checked at your Toyota dealer in the following cases: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.
D The light does not come on even if the ignition key is turned on with the park- ing brake released.
’06Camry_U (L/O 0507)
A warning light turning on briefly during operation does not indicate a problem.
(b) Driver’s Seat Belt Reminder Light
and Buzzer
CAUTION
If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The
light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.
D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.
The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer stops after about 6 seconds. If the vehicle speed rises above 15 km/h (9 mph) with the seat belt unfastened, the buzzer will sound for about 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 15 km/h (9 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the front passenger’s seat belt is fastened.
121
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
(d) Charging System Warning Light This warning the light comes on when ignition switch is turned to the “ON” posi- tion, and goes off when is started. When there are problems in the charging system while the engine is running, the warning light comes on.
the engine
NOTICE
When the charging system warning light comes on while the engine is running, malfunctions such as the en- gine drive belt being broken may have occurred. If the warning light comes on, immediately stop the vehicle in a safe place and contact your Toyota dealer.
(e) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly.
If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank
If the fuel tank is empty, refuel immedi- ately.
D Loose fuel tank cap
If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, elec- tronic throttle control system, automatic transmission electrical system or warn- ing light system itself.
Contact your Toyota dealer as soon as possible to service the vehicle.
(c) Front Passenger’s Seat Belt Re-
minder Light and Buzzer
The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If the vehicle speed rises above 15 km/h (9 mph) with the seat belt unfastened, the buzzer will sound for about 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 15 km/h (9 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the front passenger seat, depending on its weight, flash and buzzer to sound.
the reminder
light
to
122
2006 CAMRY from July ‘05 Prod. (OM33708U)
If engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in the elec- tronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key to “ACC” or “LOCK” position.
turned
is
CAUTION
Be especially careful to prevent erro- neous pedal operation.
’06Camry_U (L/O 0507)
if
inspection
Emissions inspection and maintenance
(I/M) programs
Your vehicle may not pass a state
emission
the malfunction
indicator lamp remains on. Contact your
to check your vehicle’s
Toyota dealer
emission
and OBD
(On−Board Diagnostics) system before
taking your vehicle for the inspection.
For details, see “Emissions Inspection and
Maintenance (I/M) programs” on page 299
in Section 6.
system
control
(f) Low Engine Oil Pressure Warning
Light
This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.
light may occasionally
low. It
NOTICE
the Do not drive warning light on—even for one block. It may ruin the engine.
the vehicle with
123
2006 CAMRY from July ‘05 Prod. (OM33708U)
’06Camry_U (L/O 0507)
If either of the following conditions oc- curs, this indicates a malfunction some- where in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.
D The light comes on while you are driv-
ing.
A warning light turning on briefly during operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer.