Download PDF Manual

Anchor brackets


2. To remove the child restraint system, press the buckle−release button and al- low the belt to retract.


Follow the procedure below for a child restraint system that requires the use of a top strap.


Use the anchor bracket on the package tray behind the rear seat to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the location of the anchor brackets.


for each


installed


81


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


TO USE THE ANCHOR BRACKET: 1. Outside anchor brackets only—


Remove the head restraint.


2. Open the lid of the anchor bracket


to open.


82


3. Securely


fasten


the child restraint


system with the seat belt. Latch bracket and tighten the top strap.


the hook onto


the anchor


instructions


For the child re- straint system, see “Child restraint” on page 69 in this section.


install


to


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


—Installation with child restraint lower anchorages


4. Outside anchor brackets only—


Replace the head restraint.


specifications


Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of both outside rear seats. Child restraint systems complying with the FMVSS225 or CMVSS210.2 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.


Canada only


Type A


83


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


RESTRAINT


For owners in Canada The symbol on a child restraint system indicates the presence of a lower connec- tor system. CHILD INSTALLATION Type A— 1. Widen


the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages around the tag on the seat cushion.


SYSTEM


2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen


the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages around the tag on the seat cushion.


2. Latch the buckles onto the anchor-


ages.


it should be anchored. (For


If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 81 in this section.)


Canada only


Type B


84


the installation details, refer


For to the instruction manual equipped with each product.


CAUTION


D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.


D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.


it


the


lock mechanism of


D Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. This can cause death or serious injury to the child and front passenger in case of sudden brak- ing or a collision.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Tilt steering wheel


Power adjustable pedals (some models with an automatic transmission)


CAUTION


D Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.


D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.


To change the steering wheel angle, hold the steering wheel, push down the lock the steering wheel to the desired angle and return the lever to its original position.


release


lever,


tilt


To adjust the position of the accelerator and brake pedals, push the switch. The ignition key must be in the “ON” posi- tion with the automatic transmission selec- tor lever in the “P” position. To move the pedals toward the front of the vehicle: Push the switch. To move Push the “Ɯ” side of the switch. The accelerator and brake pedals will move simultaneously as long as you hold the switch.


the “Ɲ” side of


the pedals back


toward you:


85


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Outside rear view mirrors—


When you set your driving position: 1. Set the parking brake firmly. 2. Move the accelerator and brake pedals


to the front most position.


3. Adjust the seat position and steering wheel angle properly. “Front seats” on page 38 and “Tilt steering wheel” on page 85.)


(See


4. Move the pedals toward you until you


can fully depress the brake pedal.


5. After adjusting, depress the pedals a


few times to get used to the feel.


CAUTION


D Never put your foot on the acceler- ator pedal while the pedals are moving. It may cause racing of the engine or sudden acceleration.


D Make sure that you can fully de- press the brake pedal before driv- ing. Otherwise, you may not be able to hold down the brake pedal firmly in an emergency stop.


86


Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the rear window defogger switch, the heater panels in the outside rear view mirrors will quick- ly clear the mirror surface. (See “Rear window and outside rear view mirror de- foggers” on page 99 in Section 1−4.)


CAUTION


D Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.


D Since the mirror surfaces can get hot, do not touch them when the defogger switch is on.


NOTICE


The outside rear view mirrors are fixed in place. Do not try to fold the mirrors. It may damage the mirrors.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


—Power rear view mirror control


Anti−glare inside rear view mirror


NOTICE


If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.


To adjust a mirror, use the switches. 1. Master switch—To select the mirror to


the switch to “L” (left) or “R”


be adjusted Push (right). 2. Control


switch—To move


ror P ush direction.


the switch


in


the mir- the desired


Mirrors can be adjusted when the key is in the “ACC” or “ON” position.


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.


87


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Auto anti−glare inside rear view mirror


CAUTION


Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.


88


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.


ignition key


the


is


to reduce


In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “MIRROR” switch. To turn on the automatic function again, push the “MIRROR” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it for the mirror to may take little longer darken to the detection of headlights.


in response


CAUTION


Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Vanity mirrors


To use the vanity mirror, swing down the sun visor and open the cover. Vanity lights (type B only)— The lights come on when you open the cover. To adjust the brightness of the lights, slide the switch.


To ensure correct functioning of an anti−glare mirror sensor located on the back side of the mirror, do not touch or cover the sensor with your finger or a piece of cloth, etc.


Type A


Type B


89


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


90


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


SECTION 1− 4


OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Ignition switch light Personal lights Windshield wipers and washer Rear window and outside rear view mirror defoggers


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


92
95
96
96
97
97
98
98
99


91


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Headlights and turn signals (without automatic light control system)


Position 2— The lights automatically turn off after 30
seconds when any of the door or trunk lid is opened and closed with the ignition key in the “ACC” or “LOCK” position. If you want to turn off the lights immedi- ately, push the “LOCK” button on the wire- less remote control transmitter twice. The lights also can be turned off immediately by pushing the “LOCK” button on the wire- less remote control transmitter with all the doors locked and the trunk lid closed. If any of the door or trunk lid is kept opened, the lights automatically turn off after 20 minutes. To turn on the lights again, turn the igni- tion key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is in the “DRL” or “DRL OFF” position.


NOTICE


To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.


Daytime running light (DRL) system Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many different driving conditions, but they can be espe- cially helpful the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The light switch is in the “DRL” posi-


in


tion.


D The ignition is on with the engine run-


ning.


D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights for night driving. To turn off the DRL system, twist the knob to the position 3 (“DRL OFF”) or turn the ignition switch off.


to full intensity


tail,


license plate,


HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Automatic light cut off system Position 1— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.


the


92


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Headlights and turn signals (with automatic light control system)


High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “DRL” or “DRL OFF”.


the lever all


TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 279 in Section 7−3.


tail,


license plate,


HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Position 3 (“AUTO”)—Headlights and/or all of the lights in the position 1
They automatically turn on or off depend- ing on the darkness of the surroundings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.


the


93


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Daytime running light (DRL) system Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many different driving conditions, but they can be espe- cially helpful the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The ignition is on with the engine run-


in


ning.


D The headlight switch is off. D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights for night driving.


to full intensity


Position 2 or position 3 with the head- lights on— The lights automatically turn off after 30
seconds when any of the door or trunk lid is opened and closed with the ignition key in the “ACC” or “LOCK” position. If you want to turn off the lights immedi- ately, push the “LOCK” button on the wire- less remote control transmitter twice. The lights also can be turned off immediately by pushing the “LOCK” button on the wire- less remote control transmitter with all the doors locked and the trunk lid closed. If any of the door or trunk lid is kept opened, the lights automatically turn off after 20 minutes. To turn on the lights again, turn the igni- tion key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.


NOTICE


To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.


top of


the driver’s side


The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. Automatic light cut off system Position 1 or position 3 with the tail lights on— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.


94


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Emergency flashers


High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.


the lever all


TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 279 in Section 7−3.


flashers,


turn on


the emergency


To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.


95


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Instrument panel light control


Front fog lights


NOTICE


To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.


To adjust the brightness of the instru- ment panel lights, turn the dial.


To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.


96


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Interior light


Ignition switch light


ILLUMINATED ENTRY SYSTEM When the switch is in the “DOOR” posi- tion and any door is opened, the light will come on. After all the doors are closed, the light remains on for about 15 seconds before fading out. However, in the following cases, the light go off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.


To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns light on when any door is opened. The light goes off when all the doors are closed.


the


D The ignition key is turned to the “ACC”, the side


“START” after all


“ON” or doors are closed.


D All the doors are closed and locked. When all the doors are unlocked using either the key or the wireless remote con- trol transmitter simultaneously, the interior light will come on and remain on for about 15 seconds before fading out. To prevent the battery being discharged, the light will automatically turn off when the key is removed and the door is left opened with the switch at the “DOOR” position for 20 minutes or more.


For easy access to the ignition switch, the ignition switch light comes on when any of the doors are opened. The light remains on for about 15 seconds after all the doors are closed. However, in the following cases, the light goes off immediately. D All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.


D The ignition key is turned to the “ACC”, the side


“START” after all


“ON” or doors are closed.


D All the doors are closed and locked.


97


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


When all the doors are unlocked using either the key or the wireless remote con- trol transmitter simultaneously, the ignition switch light will come on and remain on for about 15 seconds before fading out. To prevent the battery being discharged, the light will automatically turn off when the key is removed and the door is left opened for 20 minutes or more.


’03Camry_U (L/O 0301)


Personal lights


Windshield wipers and washer


To turn on the front personal lights, push the lenses. To turn the lights off, push the lenses once again.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Position 3


Intermittent


Slow


Fast


For a single sweep of push the lever up and release it.


the windshield,


98


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


to


the


increase


interval adjuster: The


With “INT TIME” band lets you adjust the wiping time inter- val when the wiper lever is in the intermit- tent position (position 1). Twist the band upward time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 279 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield the glass.


It may scratch


is dry.


’03Camry_U (L/O 0301)


Rear window and outside rear view mirror defoggers


When waxing your vehicle, make sure that the washer nozzles do not become blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the vehicle serviced.


NOTICE


If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.


With manual air conditioning controls


With automatic air conditioning controls


99


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.


NOTICE


When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.


To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the sur- faces. An indicator light will illuminate to indicate the defogger is operating. On some models, heater panels in the outside rear view mirrors will also quickly clear the surfaces. Push the switch once again to turn the defogger off. The system will automatically shut off af- ter the defogger has operated about 15
minutes.


CAUTION


Since the mirror surfaces can get hot do not touch them when the defogger switch is on.


turn


Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow.


100


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


SECTION 1− 5


OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers


102
102
103
103
105


101


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Fuel gauge


Engine coolant temperature gauge


On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


indicates


The gauge the approximate quantity of the fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The gauge remains on for about 10 min- utes after the ignition switch is off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible.


102


The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high


speed driving.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Tachometer


Odometer and two trip meters


D Idling for a long period with the air conditioning on in stop−and−go traffic.


D Towing a trailer.


NOTICE


z Do not remove the thermostat


in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.


z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 226 in Section 4.


thousands


The tachometer indicates engine speed in of rpm ( revolutions per minute). Use it while driving to se- lect correct shift points and to prevent engine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.


NOTICE


Do not let the indicator needle get into the red zone. This may cause severe engine damage.


trip meters when


This meter displays the odometer and two ignition switch is on. 1. Odometer—Shows


total distance


the


the


the vehicle has been driven.


2. Two


trip meters—Show


two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.


fuel economy and


the other


103


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B. This display remains on for about 10 min- utes after the ignition switch is off.


to


104


’03Camry_U (L/O 0301)


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Service reminder indicators and warning buzzers


If the indicator or buzzer comes on...


Do this.


(a)


(b)


(c)


(d)


(e)


(f)


(g)


or


If parking brake is off, stop immediately and contact Toyota dealer.


(indicator and buzzer)


Fasten driver’s seat belt.


Fasten front passenger’s seat belt.


Stop and check.


Take vehicle to Toyota dealer.


Stop and check.


Fill up tank.


105


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


If the indicator or buzzer comes on...


Do this.


or


Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.


Close all doors.


Take vehicle to Toyota dealer immediately.


Add washer fluid.


Take vehicle to Toyota dealer.


(h)


(i)


(j)


(k)


(l)


(m)


Key reminder buzzer


Remove key.


106


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... Vehicles with anti−lock brake system— This light comes on for a few seconds when to the “ON” position even after the parking brake is released. D When the brake fluid level is low...


ignition key


turned


the


is


CAUTION


It is dangerous to continue driving normally when the brake fluid level is low.


Have your vehicle checked at your Toyota dealer in the following cases: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.


Vehicles with anti−lock brake system— D The light does not come on even if the ignition key is turned on with the park- ing brake released.


’03Camry_U (L/O 0301)


A warning light turning on briefly during operation does not indicate a problem.


(b) Driver’s Seat Belt Reminder Light


and Buzzer


CAUTION


If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The


light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.


Vehicles with anti−lock brake sys- tem— D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.


to


reminder


remind you


light and buzzer


This buckle up the driver’s seat belt. Once the ignition key is turned to “ON”, the flashes and buzzer sounds if the driver’s seat belt is not fas- tened. Unless the driver fastens the belt, the light keeps flashing and the buzzer stops after about 4 to 8 seconds. (c) Front Passenger’s Seat Belt Re-


light


minder Light


This light reminds you to buckle up the front passenger’s seat belt. Once the ignition key is turned to “ON”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. However, if a front passenger uses an additional seat cushion, flash even when the seat belt is not buckled up. If luggage or other load is placed on the front outside passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the re- minder light to come on.


light may not


the


107


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


(d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.


NOTICE


Do not continue driving if the engine drive belt is broken or loose.


(e) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank


If the fuel tank is empty, refuel immedi- ately.


108


D Loose fuel tank cap


If the fuel tank cap is loose, securely tighten it.


These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp will not go off even after the several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, elec- tronic throttle control system, automatic transmission electrical system or warn- ing light system itself.


Contact your Toyota dealer as soon as possible to service the vehicle. If the engine speed does not increase with the accelerator pedal depressed down, there may be a problem somewhere in your electronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible.


Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the to “ACC” or ignition key “LOCK” position.


turned


is


CAUTION


Be especially careful to prevent erro- neous pedal operation.


if


inspection


Emissions inspection and maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your Toyota dealer to check your vehicle’s emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” on page 254
in Section 6.


system


control


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


(f) Low Engine Oil Pressure Warning


Light


This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.


light may occasionally


low. It


NOTICE


the Do not drive warning light on—even for one block. It may ruin the engine.


the vehicle with


’03Camry_U (L/O 0301)


(g) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual. (h) “ABS” Warning Light Vehicles without vehicle skid control sys- tem— The light comes on with the ignition key turned to the “ON” position. If the anti− lock brake system works properly, the light turns off after a few seconds. There- after, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, but the brake system still operates con- ventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.


the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.


D The light comes on while you are driv-


ing.


A warning light turning on briefly during operation does not indicate a problem.


CAUTION


If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.


109


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


the


the systems malfunctions,


Vehicles with vehicle skid control sys- tem— The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system work properly, the light turns off after a few seconds. Thereafter, if either of light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, traction control system and the vehicle skid control system do not oper- ate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden brake or braking on slippery road surfaces.


110


’03Camry_U (L/O 0301)


the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.


D The light comes on while you are driv-


ing.


A warning light turning on briefly during operation does not indicate a problem.


CAUTION


If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.


light system monitors


(i) Open Door Warning Light This light remains on until all the doors are completely closed. (j) SRS Warning Light This light will come on when the igni- tion key is turned to the “ON” position. After about 6 seconds, the light will go off. This means the systems of the air- bag and front seat belt pretensioner are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, front seat belt pretensioner assemblies, inflators, warning light, inter- connecting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion or remains on.


D The light comes on or flashes while


driving.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed. (m) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.


(k) Low Windshield Washer Fluid Level


Warning Light


The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” on page 279 in Section 7−3.) (l) “VSC” Warning Light The light warns that there is a problem somewhere in the vehicle skid control sys- tem or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after about a few seconds. If the light comes on, the vehicle skid control system and traction control system do not work. However, as conventional braking operates when applied, there is no problem to continue your driving. In the following cases, contact your Toyota dealer: D The light does not come on after the


ignition is turned to on.


D The light is left on after the ignition is


turned to on.


D The light comes on while driving.


light


SERVICE


CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.


and


The open door warning come on.


light should


3. Close the door.


The open door warning light should go off.


4. Turn the ignition key to “ON”, but do


not start the engine. All the service reminder indicators ex- cept the open door warning light should come on. The “ABS” and “VSC” warn- ing lights, “TRAC OFF” and slip indica- tor lights go off after a few seconds. The SRS warning light goes off after about 6 seconds.


If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.


111


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


112


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


SECTION 1− 6


OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual transmission Traction control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle skid control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


114
115
123
124
126
128
129


113


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


CAUTION


For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.


NOTICE


leave the key


Do not in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.


“LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be put in the “P” position before pushing the key. Vehicles with engine immobiliser system— Once you remove the key, the engine im- mobiliser system is automatically set. (See “Engine immobiliser system” on page 15
in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently. If the automatic unlocking operation linked with the ignition switch is set, all doors are automatically unlocked when the igni- tion switch is turned from the “ON” posi- tion to the “ACC” or “LOCK” position. For details, see “—Automatic door locking and unlocking functions” on page 19 in Section 1−2.


Ignition switch with steering lock


“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see page 207 in Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key.


the key


leave


in


114


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Automatic transmission "2AZ−FE engine


Lock release button To prevent misshifting


Selector lever


With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in “ON” position.)


Shift while holding the lock release button in.


Shift normally.


Overdrive switch


Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, engine starting and


key removal


R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking


115


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” on page 129 in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” on page 208 in Section 3. The transmission must be in “P” or “N”.


2. With your foot holding down the brake


pedal, shift the selector lever to “D”.


When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.


temperature


low,


is


CAUTION


Never put your foot on the accelera- tor pedal while shifting.


3. Release the parking brake and brake the accelerator pedal


pedal. Depress slowly for smooth starting.


If the automatic locking operation linked with the shift position is set, all doors are automatically locked when the shift lever is moved out of the “P” position with the ignition switch is in the “ON” position and all the doors are closed. For details, see “—Automatic door locking and unlocking functions” on page 19 in Section 1−2. (d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will be on automatically.


for better


116


’03Camry_U (L/O 0301)


D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than 107 km/h (66 mph), and stronger engine braking will be en- abled.


D Shift into the “L” position. The trans- first gear mission will downshift when the vehicle speed drops down to or lower than 53 km/h (32 mph), and maximum engine braking will be en- abled.


to


Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” on page 129 in this section.


CAUTION


Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.


surface. Abrupt


(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.


NOTICE


z Be careful not to over−rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:


“2” “L”


. . . . . . . . . . . . . . . . . . . . . . .


115 km/h (71 mph) 64 km/h (40 mph)


z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.


(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.


NOTICE


Never shift into reverse while the ve- hicle is moving.


(g) Parking 1. Bring the vehicle to a complete stop. 2. Pull the parking brake lever up fully to


securely apply the parking brake.


3. With


the brake pedal pressed down, shift the selector lever to the “P” posi- tion.


117


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


CAUTION


CAUTION


Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.


If the automatic unlocking operation linked with the shift position is set, all doors are automatically unlocked when the selector lever is moved to the “P” position with the ignition switch is in the “ON” position. For details, see “—Automatic door locking and unlocking functions” on page 19 in Section 1−2. (h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.


D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.


Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.


NOTICE


Always use the brake pedal or the parking brake to hold the vehicle on an upgrade. Do not attempt to hold the vehicle using the accelerator ped- al, as this can cause the transmission to overheat.


(i)


If you cannot shift the selector le- ver out of “P” position


If you cannot shift the selector lever from “P” position even though the brake pedal is depressed, use the shift lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” on page 241 in Section 4.


118


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


"1MZ−FE engine


Lock release button To prevent misshifting


Selector lever


With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in “ON” position.)


Shift while holding the lock release button in.


Shift normally.


Overdrive switch


Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, engine starting and


key removal


R: Reverse N: Neutral D: Normal driving (with overdrive on) 3, 2: Stronger engine braking L: Maximum engine braking


119


2003 CAMRY from Jan. ’03 Prod. (OM33593U)


’03Camry_U (L/O 0301)


Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” on page 129 in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” on page 208 in Section 3. The transmission must be in “P” or “N”.


2. With your foot holding down the brake


pedal, shift the selector lever to “D”.


When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.


temperature


low,


is


CAUTION


Never put your foot on the accelera- tor pedal while shifting.


3. Release the parking brake and brake the accelerator pedal


pedal. Depress slowly for smooth starting.


If the automatic locking operation linked with the shift position is set, all doors are automatically locked when the shift lever is moved out of the “P” position with the ignition switch is in the “ON” position and all the doors are closed. For details, see “—Automatic door locking and unlocking functions” on page 19 in Section 1−2. (d) Using engine braking

Loading...
x