2012 Toyota Camry HV Owners Manual

The symbol on a child restraint system indicates the presence of a lower connector system.

STEP 2

Canada only

139

1-8. Safety information

Installing child restraints using a seat belt (child restraint lock function belt)

■ Rear facing ⎯ Infant seat/convertible seat STEP 1

Place the child restraint system on the rear seat facing the rear of the vehicle.

Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

STEP 2

STEP 3

140

STEP 4

1-8. Safety information

While pushing the child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

■ Forward facing ⎯ Convertible seat STEP 1

Place the child restraint system on the seat facing the front of the vehicle.

STEP 2

STEP 3

Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted.

Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.

141

1-8. Safety information

STEP 4

While pushing the child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (→P. 143)

STEP 5

■ Booster seat STEP 1

Place the child restraint system on the seat facing the front of the vehicle.

STEP 2

142

Sit the child in the child restraint system. Fit the seat belt to the child restraint system according to the manufacturer's instruc- tions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child's shoulder and that the lap belt is as low as possible. (→P. 85)

1-8. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Child restraint systems with a top tether strap

STEP 1

STEP 2

Secure the child restraint using the seat belt or LATCH anchors.

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched.

143

1-8. Safety information

■Laws and regulations pertaining to anchorages

The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to SAE J1819.

CAUTION

■When installing a booster seat

To prevent the belt from going into ALR lock mode, do not fully extend the shoulder belt. ALR mode causes the belt to tighten only. This could cause injury or discomfort to the child. (→P. 87)

144

1

1-8. Safety information

CAUTION

■When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.

●If the driver's seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

●Adjust the front passenger seat so that it does not interfere with the child restraint system.

●Only put a forward-facing child restraint system on the front seat when unavoid- able. When installing a forward-facing child restraint system on the front pas- senger seat, move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated. Failure to do so may result in death or serious injury if the airbags deploy (inflate).

145

1-8. Safety information

CAUTION

■When installing a child restraint system

●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Failure to do so may result in death or serious injury in the event of sudden braking, sudden swerving or an accident.

●Ensure that the belt and plate are securely locked and the seat belt is not

twisted.

●Push and pull the child restraint system from side to side and forward to be

sure it is secure.

●After securing a child restraint system, never adjust the seat. ●Follow all installation instructions provided by the child restraint system

manufacturer.

■Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sud- den braking, sudden swerving or an accident.

■To correctly attach a child restraint system to the anchors

When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of sudden braking, sudden swerve or an accident.

146

2-1. Driving procedures Driving the vehicle

The following procedures should be observed to ensure safe driv- ing: ■ Starting the hybrid system

→P. 159
■ Driving STEP 1

STEP 2

STEP 3

With the brake pedal depressed, shift the shift lever to D. (→P. 169) Release the parking brake. (→P. 172) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.

■ Stopping STEP 1

STEP 2

With the shift lever in D, depress the brake pedal. If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to P. (→P. 169)

■ Parking the vehicle STEP 1

With the shift lever in D, depress the brake pedal. Set the parking brake. (→P. 172) Shift the shift lever to P. (→P. 169) If parking on a hill, block the wheels as needed. Press the “POWER” switch to stop the hybrid system. Lock the door, making sure that you have the electronic key on your person.

STEP 2

STEP 3

STEP 4

STEP 5

148

2

2-1. Driving procedures

Starting off on a steep uphill

STEP 1

STEP 2

STEP 3

Make sure that the parking brake is set and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be

especially slippery.

●Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Engine speed while driving

In the following conditions, the engine speed may become high while driving. This is due to automatic up-shifting control or down-shifting implementation to meet driving conditions. It dose not indicate sudden acceleration. ●The vehicle is judged to be driving uphill or downhill ●When the accelerator pedal is released

■Breaking in your new Toyota

To extend the life of the vehicle, observing the following precautions is rec- ommended: ●For the first 200 miles (300 km):

Avoid sudden stops.

●For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive at a constant speed for extended periods.

149

2-1. Driving procedures

■Drum-in-disc type parking brake system

Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down operation.

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 474)

■For efficient use

●Shift the shift lever to D when driving.

In the N position, the gasoline engine operates but electricity cannot be generated. The hybrid battery (traction battery) will discharge, requiring unnecessary engine power to recharge.

●Drive your vehicle smoothly.

Avoid abrupt acceleration and deceleration. Gradual acceleration and deceleration will make more effective use of the electric motor (traction motor) without having to use gasoline engine power.

●Avoid repeated acceleration.

Repeated acceleration consumes hybrid battery (traction battery) power, resulting in poor acceleration. Battery power can be restored by driving with the accelerator pedal slightly released.

●Shift the shift lever to P when parking.

In the N position, the hybrid battery (traction battery) does not recharge. Leaving the shift lever in the N position for an extended period of time may discharge the hybrid battery. The vehicle cannot run if the hybrid battery is discharged.

■When “DRIVING FORCE LIMITED” is displayed on the multi-informa-

tion display Driving force is being limited. This is not a malfunction.

150

2

2-1. Driving procedures

CAUTION

■When starting the vehicle

Always keep your foot on the brake pedal while stopped with the hybrid sys- tem operating. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly. This allows you to depress the brake and acceler- ator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●When the hybrid vehicle is driven using the electric motor only, no engine noise is made. As such, pedestrians, people riding bicycles or other peo- ple and vehicles in the surrounding area may not realize that the vehicle is approaching. Even with the Vehicle Proximity Notification System active, people may not realize the vehicle is approaching when the surrounding area is noisy and so forth. Therefore, take extra care while driving.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. These hot parts may cause a fire if there is any flammable material nearby.

●Do not let the vehicle roll backward while the shift lever is in a driving posi-

tion, or roll forward while the shift lever is in R. Doing so may result in an accident or damage to the vehicle.

●If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.

151

2-1. Driving procedures

CAUTION

●Do not shift the shift lever to P while the vehicle is moving.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to R while the vehicle is moving forward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to D while the vehicle is moving backward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Moving the shift lever to N while the vehicle is moving will disengage the hybrid system. Engine braking is not available with the hybrid system dis- engaged.

●During normal driving, do not turn off the hybrid system. Turning the hybrid system off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: →P. 470

●Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 169)

●Do not adjust the position of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents, resulting in death or serious injury.

●Always check that all passengers' arms, heads or other parts of their body

are not outside the vehicle, as this may result in death or serious injury.

152

2

2-1. Driving procedures

CAUTION

●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. ■When driving on slippery road surfaces

●Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

●Sudden acceleration, engine braking due to shift changing, or changes in

engine speed could cause the vehicle to skid, resulting in an accident.

●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

■When shifting the shift lever

Be careful not to shift the shift lever with the accelerator pedal depressed. Shifting the shift lever to a gear other than P or N may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

■If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or those of the brake discs are exceeded.

153

2-1. Driving procedures

CAUTION

■When the vehicle is stopped

●Do not depress the accelerator pedal unnecessarily.

If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, causing an accident.

●Do not leave the vehicle with the hybrid system on for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

●In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the “READY” indicator is on. Apply the parking brake as necessary.

●If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.

●Avoid revving or racing the engine.

Running the engine at high speed while the vehicle is stopped may cause the exhaust system to overheat, which could result in a fire if combustible material is nearby.

154

2

2-1. Driving procedures

CAUTION

■When the vehicle is parked

●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle's electrical components.

●Do not leave cigarette lighters in the vehicle. If a cigarette lighter is in a place such as the glove box or on the floor, it may be lit accidentally when luggage is loaded or the seat is adjusted, causing a fire.

●Do not attach adhesive discs to the windshield or windows. Do not place containers such as air fresheners on the instrument panel or dashboard. Adhesive discs or containers may act as lenses, causing a fire in the vehi- cle.

●Do not leave a door or window open if the curved glass is coated with a metallized film such as a silver-colored one. Reflected sunlight may cause the glass to act as a lens, causing a fire.

●Always apply the parking brake, shift the shift lever to P, stop the hybrid

system and lock the vehicle. Do not leave the vehicle unattended while the hybrid system is operating. ●Do not touch the exhaust pipe while the hybrid system is operating or

immediately after turning the hybrid system off. Doing so may cause burns.

●Do not leave the hybrid system operating in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the hybrid system is operating, exhaust gases may collect and enter the vehi- cle. This may lead to death or a serious health hazard.

155

2-1. Driving procedures

CAUTION

■Exhaust gases

Exhaust gases include harmful carbon monoxide (CO), which is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health hazard. ●If the vehicle is in a poorly ventilated area, stop the hybrid system. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

●The exhaust system should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. ■When taking a nap in the vehicle

Always turn the hybrid system off. Otherwise, if you accidentally move the shift lever or depress the accelerator pedal, this could cause an accident or fire due to hybrid system overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

156

2

2-1. Driving procedures

CAUTION

■When braking

●When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.

●If the electronically controlled brake system does not operate, do not fol- low other vehicles closely and avoid hills or sharp turns that require brak- ing. In this case, braking is still possible, but the brake pedal should be depressed more firmly than usual. Also, the braking distance will increase. ●The brake system consists of 2 individual hydraulic systems; if one of the systems fails, the others will still operate. In this case, the brake pedal should be depressed more firmly than usual and the braking distance will increase. If this happens, do not continue to drive the vehicle. If the brake system warning light (red indicator) comes on together with the buzzer sound while driving, immediately stop the vehicle in a safe place and con- tact your Toyota dealer.

NOTICE

■When driving the vehicle

●Do not depress the accelerator and brake pedals at the same time during

driving, as this may restrain driving torque.

●Do not use the accelerator pedal or depress the accelerator and brake

pedals at the same time to hold the vehicle on a hill.

■When parking the vehicle

Always shift the shift lever to P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is acci- dentally depressed.

157

2-1. Driving procedures

NOTICE

■Avoiding damage to vehicle parts

●Do not turn the steering wheel fully in either direction and hold it there for

an extended period of time. Doing so may damage the power steering motor.

●When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

■If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down and stop the vehicle in a safe place. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds or vibrations. ●The vehicle will behave abnormally. Information on what to do in case of a flat tire (→P. 442)

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle: ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ●Brake function ●Changes in quantity and quality of oil and fluid used for the engine, hybrid

transmission, etc.

●Lubricant condition for the bearings and suspension joints (where possi-

ble), and the function of all joints, bearings, etc.

158

2-1. Driving procedures Power (ignition) switch

STEP 2

STEP 3

STEP 4

Performing the following operations when carrying the electronic key on your person starts the hybrid system or changes “POWER” switch modes. ■ Starting the hybrid system STEP 1

Check that the parking brake is set. Check that the shift lever is set in P. If the shift lever is not set in P, the hybrid system may not be started. (→P. 169) Firmly depress the brake pedal.

will be displayed on the multi-information display.

If it is not displayed, the hybrid system cannot be started.

Press the “POWER” switch.

After a while, the “READY” indicator comes on with a beep sound. The vehicle can move when the “READY” indicator is on even if the engine is stopped. Continue depressing the brake pedal until the hybrid system is completely started. The hybrid system can be started from any “POWER” switch mode.

STEP 5

Check that the “READY” indicator is on. The vehicle will not move when the “READY” indicator is off.

159

2-1. Driving procedures

■ Stopping the hybrid system STEP 1

Stop the vehicle. Shift the shift lever to P. Set the parking brake. (→P. 172) Release the brake pedal. Press the “POWER” switch.

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

Check that

on the multi-information display is off.

160

2

2-1. Driving procedures

■ Changing “POWER” switch modes

Modes can be changed by pressing the “POWER” switch with brake pedal released. (The mode changes each time the switch is pressed.)

Off*

The emergency flashers can be used. The multi-information display will not be displayed. ACCESSORY mode

Some electrical components such as the audio system can be used.

will be displayed on

the multi-information display.

ON mode

All electrical components can be used.

will be displayed on

the multi-information display.

*: If the shift lever is in a position other than P when turning off the the “POWER” switch will be turned to ACCESSORY mode, not to off.

system,

hybrid

161

2-1. Driving procedures

When stopping the hybrid system with the shift lever in a position other than P

If the hybrid system is stopped with the shift lever in a position other than P, the “POWER” switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off: STEP 1

Check that the parking brake is set. Shift the shift lever to P.

STEP 2

STEP 3

Check that

is displayed on the multi-information dis-

play and then press the “POWER” switch once.

STEP 4

Check that

on the multi-information display is off.

■Auto power off function

If the vehicle is left in ACCESSORY mode for more than 20 minutes or ON mode (the hybrid system is not operating) for more than an hour with the shift lever in P, the “POWER” switch will automatically turn off. However, this function cannot entirely prevent 12-volt battery discharge. Do not leave the vehicle with the “POWER” switch in ACCESSORY or ON mode for long peri- ods of time when the hybrid system is not operating.

■Sounds and vibrations specific to a hybrid vehicle

→P. 32

■Electronic key battery depletion

→P. 63

■When the ambient temperature is low, such as during winter driving

conditions It may take time until the “READY” indicator comes on.

■Conditions affecting operation

→P. 60

162

2-1. Driving procedures

■Note for the entry function

→P. 61

■If the hybrid system does not start

●The immobilizer system may not have been deactivated. (→P. 108)

●Check that the shift lever is securely set in P. The hybrid system may not start if the shift lever is displaced out of P. “SHIFT TO P POSITION TO START” will be displayed on the multi-informa- tion display.

■Steering lock

After turning the “POWER” switch off and opening and closing the doors, the steering wheel will be locked due to the steering lock function. Operating the “POWER” switch again automatically cancels the steering lock.

■When the steering lock cannot be released

“STEERING LOCK ACTIVE” will be dis- played on the multi-information display. Check that the shift lever is set in P. Press the “POWER” switch while turning the steering wheel left and right.

■Steering lock motor overheating prevention

To prevent the steering lock motor from overheating, the motor may be sus- pended if the hybrid system is turned on and off repeatedly in a short period of time. In this case, refrain from operating the hybrid system. After about 10
seconds, the steering lock motor will resume functioning.

■When “CHECK SMART KEY SYSTEM” will be displayed on the multi-

information display. The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.

163

2-1. Driving procedures

■If the “READY” indicator does not come on

If the “READY” indicator does not come on when you press the “POWER” switch with the shift lever in P and the brake pedal depressed, contact your Toyota dealer immediately.

■If the hybrid system is malfunctioning

→P. 424

■If the electronic key battery is depleted

→P. 382

■Operation of the “POWER” switch

●When operating the “POWER” switch, one short, firm press is enough. If the switch is pressed improperly, the hybrid system may not start or the “POWER” switch mode may not change. It is not necessary to press and hold the switch.

●If attempting to restart the hybrid system immediately after turning the “POWER” switch off, the hybrid system may not start in some cases. After turning the “POWER” switch off, please wait a few seconds before restarting the hybrid system.

■If the smart key system has been deactivated in a customized setting

→P. 459

CAUTION

■When starting the hybrid system

Always start the hybrid system while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the hybrid system under any cir- cumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution while driving

If hybrid system failure occurs while the vehicle is moving, do not lock or open the doors until the vehicle reaches a safe and complete stop. Activa- tion of the steering lock in this circumstance may lead to an accident, result- ing in death or serious injury.

164

2-1. Driving procedures

CAUTION

■Stopping the hybrid system in an emergency

If you want to stop the hybrid system in an emergency while driving the vehi- cle, press and hold the “POWER” switch for more than 2 seconds, or press it briefly 3 times or more in succession. However, do not touch the “POWER” switch while driving except in an emer- gency. Turning the hybrid system off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

NOTICE

■To prevent 12-volt battery discharge

●Do not leave the “POWER” switch in ACCESSORY or ON mode for long

periods of time without the hybrid system on.

●If

is displayed on the multi-information display, the “POWER”

switch is not off. Exit the vehicle after turning the “POWER” switch off.

●Do not stop the hybrid system when the shift lever is in a position other than P. If the hybrid system is stopped in another shift lever position, the “POWER” switch will not be turned off but instead be turned to ACCES- SORY mode. If the vehicle is left in ACCESSORY mode, 12-volt battery discharge may occur.

■When starting the hybrid system

Do not depress the accelerator pedal unnecessarily.

■Symptoms indicating a malfunction with the “POWER” switch

If the “POWER” switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Con- tact your Toyota dealer immediately.

165

2-1. Driving procedures EV drive mode

In EV drive mode the electric motor (traction motor), powered by the hybrid battery (traction battery), is used to drive the vehicle. This mode allows you to drive in residential areas early in the morn- ing and late at night, or in indoor parking lots etc. without concern for noises and gas emissions. However, when the Vehicle Proximity Notification System is active, the vehicle may produce sound.

Turns EV drive mode on/off

When EV drive mode is turned on, the EV drive mode indica- tor will come on. Pressing the switch when in EV drive mode will return the vehicle to normal driving the gasoline engine and electric motor [trac- tion motor]).

(using

166

2

2-1. Driving procedures

■Switching to EV drive mode when the gasoline engine is cold

If the hybrid system is started while the gasoline engine is cold, the gasoline engine will start automatically after a short period of time in order to warm up. In this case, you will become unable to switch to EV drive mode. After the hybrid system has started and the “READY” indicator has illumi- nated, press the EV drive mode switch before the gasoline engine starts to switch to EV drive mode.

■Situations in which EV drive mode cannot be turned on

It may not be possible to turn EV drive mode on in the following situations. If it cannot be turned on, a buzzer will sound and a message will be shown on the multi-information display. ●The temperature of the hybrid system is high.

The vehicle has been left in the sun, driven on a hill, driven at high speeds, etc.

●The temperature of the hybrid system is low.

The vehicle has been left in temperatures lower than about 68°F (20°C) for a long period of time etc.

●The gasoline engine is warming up. ●The hybrid battery (traction battery) is low.

The remaining battery level indicated in the “Energy Monitor” display is low. (→P. 39)

●Vehicle speed is about 25 mph (40 km/h) or more. ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc. ●The windshield defogger is in use.

167

2-1. Driving procedures

■Automatic cancelation of EV drive mode

When driving in EV drive mode, the gasoline engine may automatically restart in the following situations. When EV drive mode is canceled, a buzzer will sound and the EV drive mode indicator will flash and go off. ●The hybrid battery (traction battery) becomes low.

The remaining battery level indicated in the “Energy Monitor” display is low. (→P. 39)

●Vehicle speed becomes more than about 25 mph (40 km/h). ●The accelerator pedal is depressed firmly or the vehicle is on a hill etc.

■Possible driving distance when driving in EV drive mode

EV drive mode’s possible driving distance ranges from a few hundred yards (a few hundred meters) to approximately 1.3 miles (2 km). Driving is possible at speeds of less than approximately 25 mph (40 km/h). However, depend- ing on vehicle conditions, there are situations when EV drive mode cannot be used. (The distance that is possible depends on the hybrid battery [traction battery] level and driving conditions.)

■Fuel economy

Your Toyota is designed to achieve the best possible fuel economy during normal driving (using the gasoline engine and electric motor [traction motor]). Driving in EV drive mode more than necessary may lower fuel econ- omy.

CAUTION

■Caution while driving

When driving in EV drive mode no engine noise is made. As such, pedestri- ans, people riding bicycles or other people and vehicles in the surrounding area may not be aware of the vehicle starting off or approaching them. Therefore, take extra care while driving even if the Vehicle Proximity Notifi- cation System is active.

168

2-1. Driving procedures Hybrid transmission

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever

While the “POWER” switch is in ON mode, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.

■ Shift position Purpose

Shift position

Function

Parking the vehicle/starting the hybrid system

Reversing Neutral

Normal driving

Position for engine braking

169

2-1. Driving procedures

■ Selecting Eco drive mode

When the vehicle is driven in Eco drive mode, vehicle driving force and operation of the air conditioning system (heating/cool- ing) is controlled to improve fuel efficiency.

Eco drive mode

When eco drive mode is turned on, the “ECO MODE” indicator will come on. Pressing the “ECO MODE” switch again turns eco drive mode off.

■Operation of the air conditioning system in Eco drive mode

Eco drive mode controls the heating/cooling operations and fan speed of the air conditioning system to enhance fuel efficiency. (→P. 232) To improve air conditioning performance, adjust the fan speed or turn off Eco drive mode.

■When in heavy traffic

If the shift lever is in N, the hybrid battery (traction battery) will not be charged. To help prevent the battery from discharging, avoid putting the shift lever in N for an extended period of time.

■If the shift lever cannot be shifted from P

→P. 456

CAUTION

■When driving on slippery road surfaces Do not accelerate or shift gears suddenly. Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.

170

2

2-1. Driving procedures Turn signal lever

The turn signal lever can be used to show the following intentions of the driver:

Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. left Lane change (push and hold the lever partway) The left hand signals will flash until you release the lever.

the

to

■Turn signals can be operated when The “POWER” switch is in ON mode.

■If the indicators flashes faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

171

2-1. Driving procedures Parking brake

U.S.A. Canada

To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.)

■Usage in winter time

See “Winter driving tips” for parking brake usage in winter time. (→P. 225)

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

172

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 92)

173

2-2. Instrument cluster Gauges and meters

Hybrid System Indicator Displays hybrid system power output and regenerative level Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Average fuel consumption meter Displays the average fuel consumption since the function was reset. Current fuel consumption gauge Displays the current rate of fuel consumption. Display change button →P. 176
Odometer/trip meter display →P. 176
Multi-information display →P. 185

174

2

2-2. Instrument cluster

Engine coolant temperature display/instrument panel light con- trol display Displays the engine coolant temperature and instrument panel light control. Outside temperature display →P. 301
Shift position display Displays the currently selected shift position. →P. 169
Instrument panel light control button →P. 177

175

2-2. Instrument cluster

Changing the odometer/trip meter display

Pressing the button changes the display as follows.

● Odometer

● Trip meters A and B

Displays the total distance the vehicle has been driven.

Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and dis- play different distances independently.

Press and hold the button to reset.

176

2-2. Instrument cluster

Instrument panel light control button

The brightness of the instrument panel lights can be adjusted.

Pressing the button will adjust brightness of instrument panel lights.

the

177

2-2. Instrument cluster

■The meters and display illuminate when

The “POWER” switch is in ON mode.

■Hybrid System Indicator

Power area Shows that an Eco-friendly driving range is being exceeded (during full power driving etc.) Eco area Shows that the vehicle is being driven in an Eco-friendly manner. Hybrid Eco area Shows that gasoline engine power is not being used very often. The gasoline engine will automatically stop and restart under various condi- tions. Charge area Shows that energy is being recovered via the regenerative brake.

●By keeping the indicator needle within Eco area, more Eco-friendly driv-

ing can be achieved.

●Charge area indicates regeneration* status. Regenerated energy will be

used to charge the battery.

*: When used in this manual, “regeneration” refers to the conversion of

energy created by the movement of the vehicle into electrical energy.

■Engine speed

On hybrid vehicles, engine speed is precisely controlled in order to help improve fuel efficiency and reduce exhaust emissions etc. There are times when the engine speed that is displayed may differ even when vehicle operation and driving conditions are the same.

178

2-2. Instrument cluster

■The brightness of the instrument panel lights

When the tail lights are turned on, the meter’s brightness will be reduced slightly unless the meter brightness level adjustment is set to the brightest setting. If the tail lights are turned on when the surroundings are dark, the meter’s brightness will reduce slightly. However, when the surroundings are bright, such as during the daytime, the meter’s brightness will not be reduced even if the tail lights are turned on.

■Fuel gauge and odometer/trip meter display remain on mode

After the “POWER” switch has been turned off, the fuel gauge and odome- ter/trip meter display remain on for 10 minutes, enabling the fuel gauge and odometer/trip meter values to be checked again without having to turn the “POWER” switch to ON mode. When confirming the gauges and meters, turn the headlight switch to the position. Press the display change button to change between the

odometer and trip meter displays.

NOTICE

■To prevent damage to the engine and its components

The engine may be overheating if the rightmost segment of the engine cool- ant temperature display is flashing. In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 465)

179

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster, center panel and outside rear view mirrors inform the driver of the status of the vehicle’s various systems. ■ Instrument cluster

■ Center panel

180

■ Outside rear view mirrors (if equipped)

2-2. Instrument cluster

181

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

*1, 3

*1

*1

Turn signal indicator (→P. 171)

Headlight high beam indicator (→P. 194)

Slip indicator (→P. 208)

VSC OFF indicator (→P. 209)

“TRAC OFF” indicator (→P. 209)

Security indicator (→P. 108, 110) “ECO MODE” indicator (→P. 170) “READY” indicator (→P. 159)

Shift position indica- tors (→P. 169)

*2

(if equipped)

BSM outside rear view mirror indicators (→P. 215)

(U.S.A.)

(Canada)

(if equipped) *1

Headlight indicator (→P. 192)

Tail light indicator (→P. 192)

Front fog light indicator (→P. 198)

SRS airbag on-off indi- cator (→P. 128)

Cruise control indicator (→P. 204) Cruise control set indi- cator (→P. 204)

EV Indicator (→P. 30)

EV drive mode indica- tor (→P. 166)

182

2

2-2. Instrument cluster

*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: In order to confirm operation, the BSM outside rear view mirror indi-

cators illuminate in the following situations: • When the “POWER” switch is turned to ON mode while the BSM

main switch is set to ON.

• When the BSM main switch is set to ON while the “POWER”

switch is in ON mode.

If the system is functioning correctly, the BSM outside rear view mir- ror indicators will turn off after a few seconds. If the BSM outside rear view mirror indicators do not illuminate or do not turn off, there may be a malfunction with the system. If this occurs, have the vehicle inspected by your Toyota dealer.

*3: The light flashes to indicate that the system is operating.

183

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 413)

*1

*1

*1, 2

*1, 3

*1

(red) *1

*1, 2

*1, 3

*1

*1, 2

*1, 3

*1

*1, 2

*1

(yellow) *1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is on, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: For vehicles sold in U.S.A. *3: For vehicles sold in Canada

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS and SRS warning light not come on when you start the hybrid system, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

184

2

2-2. Instrument cluster Multi-information display

The multi-information display presents the driver with a variety of driving-related data.

● Trip information (→P. 187) Displays cruising range, fuel consumption and other cruis- ing-related information.

● Warning messages

(→P. 423) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

185

2-2. Instrument cluster

■ Display contents

Trip information contents

Switching display items

Cruising range/average fuel consumption Average vehicle speed/ elapsed time Eco drive level Energy monitor Customization - (off)

Press the “DISP” button.

186

2

2-2. Instrument cluster

Trip information

■ Cruising range/average fuel consumption

Cruising range Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.

• When only a small amount of fuel is added to the tank, the display

may not be updated. When refueling, turn the “POWER” switch off. If the vehicle is refueled without turning the “POWER” switch off, the display may not be updated.

Average fuel consumption Displays the average fuel consumption since the function was reset. • The function can be reset by pressing the “DISP” button for longer

than 1 second when the average fuel consumption is displayed. The average fuel consumption meter will also be reset, returning the needle to the 0 position.

• Use the displayed average fuel consumption as a reference.

■ Average vehicle speed/elapsed time

Displays the average vehicle speed and elapsed time since the hybrid system was started.

187

2-2. Instrument cluster

■ Eco drive level

Displays the average fuel consumption and eco drive level since the hybrid system was started. Even if a different screen has been selected for the multi-information dis- play, when the “POWER” switch is turned off, the eco drive level is dis- played. This is not a malfunction. When the highest eco drive level has been achieved “EXCELLENT!” is displayed.

■ Energy monitor

Displays the status of the hybrid system (→P. 39)

■ Customization

Language, Eco Indicator (current fuel consumption gauge) and EV Indicator settings can be changed. (→P. 188)

Customizing vehicle features

It is possible to customize the language, Eco Indicator (current fuel consumption gauge) and EV Indicator settings using the “DISP” but- ton. When customizing vehicle features, ensure that the vehicle is parked in a safe place with the shift position in P and the parking brake set. ■ Language STEP 1

Press the “DISP” button to dis- play the setting screen while the vehicle is stopped, and then press and hold the “DISP” button to display the customize mode screen.

188

2

STEP 2

STEP 3

2-2. Instrument cluster

Press the “DISP” button to select the item to be set, then press and hold the “DISP” button.

Press the “DISP” button to select the desired setting, and then press and hold the “DISP” but- ton.

To go back to the previous screen or exit the customize mode, press the “DISP” button to select “EXIT”, and then press and hold the “DISP” button. ■ Eco Indicator (current fuel consumption gauge) STEP 1

Press the “DISP” button to dis- play the setting screen while the vehicle is stopped, and then press and hold the “DISP” button to display the customize mode screen.

189

2-2. Instrument cluster

STEP 2

STEP 3

Press the “DISP” button to select the item to be set, then press and hold the “DISP” button.

Press the “DISP” button to select the desired setting, and then press and hold the “DISP” but- ton.

When the “ECO INDICATOR” is set to “OFF”, the current fuel con- sumption gauge will not be dis- played.

To go back to the previous screen or exit the customize mode, press the “DISP” button to select “EXIT”, and then press and hold the “DISP” button. ■ EV Indicator STEP 1

Press the “DISP” button to dis- play the setting screen while the vehicle is stopped, and then press and hold the “DISP” button to display the customize mode screen.

190

2

STEP 2

STEP 3

2-2. Instrument cluster

Press the “DISP” button to select the item to be set, then press and hold the “DISP” button.

Press the “DISP” button to select the desired setting, and then press and hold the “DISP” but- ton.

To go back to the previous screen or exit the customize mode, press the “DISP” button to select “EXIT”, and then press and hold the “DISP” button.

NOTICE

■The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

191

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: U.S.A.

the

The headlights, parking lights, daytime running lights and so on turn on and off automatically (when “POWER” switch is in ON mode). The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above (except daytime run- ning lights) turn on. The daytime light turns off.

running

192

2

2-3. Operating the lights and wipers

Canada

(when

The headlights, park- ing lights, daytime run- ning lights and so on turn on and off auto- matically the “POWER” switch is in ON mode). The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above (except daytime run- ning lights) turn on. The daytime lights turn on.

running

193

2-3. Operating the lights and wipers

Turning on the high beam headlights

With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.

Manual headlight leveling dial (if equipped)

The level of the headlights can be adjusted according to the number of passengers and the loading condition of the vehicle.

Raises the level of the head- lights Lowers the level of the head- lights

194

2

2-3. Operating the lights and wipers

■ Guide to dial settings

Occupancy and luggage load conditions Luggage load Occupants

Dial position

Driver

Driver and front pas-

senger

All seats occupied All seats occupied

Driver

None

None

None

Full luggage loading Full luggage loading

2.5
4.5

■Daytime running light system

●To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night. U.S.A.: Daytime running lights can be turned off by operating the switch. ●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.