2012 Subaru Impreza Owners Manual

tighten the wheel nuts to the specified torque, following the tightening order in the illustration. For the wheel nut tightening torque, refer to “Tires” F12-8. Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have the wheel nut

16. Store the flat tire in the spare tire compartment. Put in the spacer and tight- en the attaching bolt firmly. Also store the jack, jack handle and wheel nut wrench in their storage locations.

WARNING

Never place a tire or tire changing tools in the passenger compartment after changing wheels. In a sudden stop or collision, loose equipment could strike occupants and cause injury. Store the tire and all tools in the proper place.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

9-8 In case of emergency

& Tire pressure monitoring

system (TPMS) (U.S.-spec. models)

that

The tire pressure monitoring system pro- vides the driver with the warning message indicated by sending a signal from a is installed in each wheel sensor when tire pressure is severely low. The tire pressure monitoring system will activate only when the vehicle is driven. Also, this system may not react immedi- ately to a sudden drop in tire pressure (for example, a blow-out caused running over a sharp object).

WARNING

If the low tire pressure warning light illuminates while driving, never

brake suddenly and keep driving straight ahead while gradually redu- cing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. Check the pressure for all four tires and adjust the pressure to the COLD tire pressure shown on the vehicle placard on the door pillar on the driver’s side. If this light still illumi- nates while driving after adjusting the tire pressure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not

inject any tire liquid or

Black plate (378,1)

aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light illuminates steadily after blinking for approximately one min- ute, promptly contact a SUBARU dealer to have the system inspected.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Jump starting

WARNING

. Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and obtain immediate medical help. Keep everyone including chil- dren away from the battery.

. The gas generated by a battery explodes if a flame or spark is brought near it. Do not smoke or light a match while jump starting. . Never attempt jump starting if the discharged battery is frozen. It could cause the battery to burst or explode.

. Whenever working on or around a battery, always wear suitable

eye protectors, and remove metal objects such as rings, bands or other metal jewelry.

. Be sure the jumper cables and clamps on them do not have loose or missing insulation. Do not jump start unless cables in suitable condition are avail- able.

. A running engine can be danger- ous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.

. Jump starting is dangerous if it done incorrectly. If you are un- sure about the proper procedure for jump starting, consult a com- petent mechanic.

When your vehicle does not start due to a run down (discharged) battery, the vehicle may be jump started by connecting your battery to another battery (called the booster battery) with jumper cables.

Black plate (379,1)

In case of emergency 9-9

& How to jump start 1. Make sure the booster battery is 12
volts and the negative terminal is grounded. 2. the booster battery is in another vehicle, do not let the two vehicles touch. 3. Turn off all unnecessary lights and accessories. 4. Connect the jumper cables exactly in the sequence illustrated.

If

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

9-10 In case of emergency

Black plate (380,1)

the other end of

(1) Connect one jumper cable to the positive (+) terminal on the discharged battery. (2) Connect the jumper cable to the positive (+) term- inal of the booster battery. (3) Connect one end of the other cable to the negative (−) terminal of the booster battery. (4) Connect the other end of the cable to the strut mounting nut of the vehicle with the discharged battery.

Make sure that the cables are not near any moving parts and that the cable clamps are not in contact with any other metal. 5. Start the engine of the vehicle with the booster battery and run it at moderate speed. Then start the engine of the vehicle that has the discharged battery. 6. When finished, carefully disconnect the cables in exactly the reverse order.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Engine overheating

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.

If the engine overheats, safely pull off the road and stop the vehicle in a safe location.

& If steam is coming from the

engine compartment

. Turn off the engine and get everyone away from the vehicle until it cools down. . Contact an authorized SUBARU deal- er.

& If no steam is coming from

the engine compartment 1. Keep the engine running at speed. 2. Open the engine hood to ventilate the

idling

Black plate (381,1)

In case of emergency 9-11

until it stops. Release the pressure from the radiator. After the pressure has been fully released, remove the cap by pressing down and turning it.

to “Engine

the coolant

engine compartment. Refer hood” F11-5. Confirm that the cooling fan is turning. If the fan is not turning, immediately turn off the engine and contact an authorized SUBARU dealer for repair. temperature high 3. After warning light that has blinked or illumi- nated in RED turns off, turn off the engine. For details about the warning light, refer to “Coolant temperature low indicator light/ temperature high warning light” Coolant F3-13. 4. After the engine has fully cooled down, check the coolant in the reserve tank. is below the “LOW” mark, add coolant up to the “FULL” mark. NOTE For details about how to check the coolant level or how to add coolant, refer to “Engine coolant” F11-11. 5. If there is no coolant in the reserve tank, add coolant to the reserve tank. Then remove the radiator cap and fill the radiator with coolant.

the coolant

level

level

If

If you remove the radiator cap from a hot radiator, first wrap a thick cloth around the radiator cap, then turn the cap counter- clockwise slowly without pressing down

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

& Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow).

CAUTION

. Use only the specified towing hook and tie-down hook. Never use suspension parts or other parts of the body for towing or tie-down purposes.

. To prevent deformation to the front bumper and the towing hook, do not apply excessive lateral load to the towing hook.

Front towing hook: 1. Take the towing hook and screwdriver out of the tool bucket. Take the jack handle out of the trunk (4-door) or cargo area (5-door).

9-12 In case of emergency

Towing

If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety.

WARNING

Never tow AWD models (both CVT and MT models) with the front wheels raised off the ground while the rear wheels are on the ground, or with the rear wheels raised off the ground while the front wheels are on the ground. This will cause the vehicle to spin away due to the operation or deterioration of the center differential.

Black plate (382,1)

2. Cover the tip of a flat-head screwdriver with vinyl tape or cloth so that it will not scratch the bumper. Insert the flat-head screwdriver into the cutout of the cover and pry open the cover.

3. Screw the towing hook into the thread

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (383,1)

In case of emergency 9-13

hole until its thread can no longer be seen.

Rear towing hook: 1. Take the towing hook and screwdriver out of the tool bucket. Take the jack handle out of the trunk (4-door) or cargo area (5-door).

4. Tighten the towing hook securely using the jack handle.

After towing, remove the towing hook from the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper.

WARNING

. Do not use the towing hook except when towing your vehicle. . Be sure to remove the towing hook after towing. Leaving the towing hook mounted on the vehicle could interfere with prop- er operation of the SRS airbag system in a frontal collision.

3. Screw the towing hook into the thread hole until its thread can no longer be seen.

2. Pry off the cover on the rear bumper using a screwdriver, and you will find a threaded hole for attaching the towing hook.

4. Tighten the towing hook securely using the jack handle.

After towing, remove the towing hook from

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

9-14 In case of emergency

the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper.

Rear tie-down holes:

WARNING

Do not use the towing hook except when towing your vehicle.

Front tie-down hooks:

The front tie-down hooks are located between each of the front tires and the front bumper.

1) Rear tie-down hole

The rear tie-down holes are located near each of the jack-up reinforcements.

Black plate (384,1)

WARNING

Use the rear tie-down holes only for downward anchoring. they are used to anchor the vehicle in any other direction, cables may slip out of the holes, possibly causing a dangerous situation.

If

& Using a flat-bed truck

This is the best way to transport your vehicle. Use the following procedures to ensure safe transportation. into the “P” 1. Shift lever position for CVT models. Shift the shift lever into the “1st” position for MT models. 2. Pull up the parking brake lever firmly. 3. Secure the vehicle onto the carrier

the select

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

properly with safety chains. Each safety chain should be equally tightened and care must be taken not to pull the chains so tightly that the suspension bottoms out.

2. The ignition switch should be in the “ACC” position while the vehicle is being towed. 3. Take up slack in the towline slowly to prevent damage to the vehicle.

CAUTION

If your vehicle has a front under- spoiler and rear underspoiler (both optional), be careful not to scrape them when placing the vehicle on the carrier and when removing the vehicle from the carrier.

& Towing with all wheels on the

ground

1. Release the parking brake and put the transmission in the “N”/neutral position.

WARNING

. Never turn the ignition switch to the “LOCK” position while the vehicle is being towed because the steering wheel and the direc- tion of the wheels will be locked. . Remember that the brake booster and power steering do not func- tion when the engine is not running. Because the engine is turned off, take greater effort to operate the brake pedal and steering wheel.

it will

CAUTION

. If

transmission failure occurs, transport your vehicle on a flat- bed truck.

. Do not run the engine while being towed using this method. Trans- mission damage could result if the vehicle is towed with the engine running.

Black plate (385,1)

In case of emergency 9-15

. For CVT models,

the traveling speed must be limited to less than 20 mph (30 km/h) and the traveling distance to less than 31
miles (50 km). For greater speeds and distances, transport your vehicle on a flat-bed truck.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

9-16 In case of emergency

Rear gate – if the rear gate cannot be opened

In the event that you cannot open the rear gate by operating the rear gate opener button, you can open it from inside the cargo area.

1. Remove the access cover at bottom-center of the rear gate trim. 2. Locate the rear gate open lever behind the rear gate trim panel.

the

CAUTION

Never operate the rear gate open lever with fingers because doing so may cause an injury. Always use a flat-head screwdriver or a similar tool.

3. To open the rear gate, turn the lever to the right position using a flat-head screw- driver or a similar tool.

Black plate (386,1)

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (19,1)

Appearance care

Exterior care ....................................................... 10-2
Washing............................................................. 10-2
Waxing and polishing ......................................... 10-3
Cleaning aluminum wheels ................................. 10-3
Corrosion protection.......................................... 10-4
Most common causes of corrosion ..................... 10-4
To help prevent corrosion................................... 10-4

Cleaning the interior.......................................... Seat fabric......................................................... Leather seat materials........................................ Synthetic leather upholstery............................... Climate control panel, audio panel, instrument

panel, console panel, and switches .................. Monitor (if equipped)..........................................

10-5
10-5
10-5
10-5

10-5
10-6

10

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

10-2 Appearance care

Exterior care & Washing

CAUTION

. When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes.

. Do not wash the engine compart- ment and area adjacent to it. If water enters the engine air intake or electrical parts, it will cause engine trouble or a malfunction of electrical equipment.

. Do not use any organic solvents when washing the surface of the bulb assembly cover. However, if a detergent with organic solvents is used to wash the cover sur- face, completely rinse off the detergent with water. Otherwise, the cover surface may be da- maged.

. For 5-door models, since your vehicle is equipped with a rear wiper, automatic car-wash

brushes could become tangled around it, damaging the wiper arm and other components. Ask the automatic car-wash operator not to let the brushes touch the wiper arm or to fix the wiper arm on the rear window glass with adhesive tape before operating the machine.

NOTE When having your vehicle washed in an automatic car wash, make sure beforehand that the car wash is of suitable type. The best way to preserve your vehicle’s beauty is frequent washing. Wash the vehicle at least once a month to avoid contamination by road grime.

Wash dirt off with a wet sponge and plenty of lukewarm or cold water. Do not wash the vehicle with hot water and in direct sunlight.

insects,

tar, soot,

Salt, chemicals, tree sap, and bird droppings should be washed off by using a light detergent, as required. If you use a light detergent, make certain that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should be promptly

Black plate (394,1)

flushed from the surface and not allowed to dry there. Rinse the vehicle thoroughly with plenty of lukewarm water. Wipe the remaining water off with a chamois or soft cloth. ! Washing the underbody Chemicals, salts and gravel used for deicing road surfaces are extremely cor- rosive, accelerating the corrosion of un- derbody components, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and sus- pension. Thoroughly flush the underbody and in- side of the fenders with lukewarm or cold water at frequent intervals to reduce the harmful effects of such agents.

Mud and sand adhering to the underbody components may accelerate their corro- sion. After driving off-road or on muddy or sandy roads, wash the mud and sand off the underbody. Carefully flush the suspen- sion and axle parts, as they are particu- larly prone to mud and sand buildup. Do not use a sharp-edged tool to remove caked mud.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

CAUTION

. Be careful not to damage brake hoses, sensor harnesses, and other parts when washing sus- pension components.

. Be careful not to flush the engine bottom for a long time. It may cause damage of some electrical parts.

! Using a warm water washer . Keep a good distance of 12 in (30 cm) or more between the washer nozzle and the vehicle. . Do not wash the same area continu- ously. . If a stain will not come out easily, wash by hand. Some warm water washers are of the high temperature, high pressure type, and they can damage or deform the resin parts such as moldings, or cause water to leak into the vehicle. & Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and apply them according to the manufac- turer’s instructions. Wax or polish when the painted surface is cool.

Be sure to polish and wax the chrome trim, as well as the painted surfaces. Loss of wax on a painted surface leads to loss of the original luster and also quickens the deterioration of the surface. It is recom- mended that a coat of wax be applied at least once a month, or whenever the surface no longer repels water.

If the appearance of the paint has dimin- ished to the point where the luster or tone cannot be restored, lightly polish the surface with a fine-grained compound. Never polish just the affected area, but include the surrounding area as well. Always polish in only one direction. A No. 2000 grain compound is recom- mended. Never use a coarse-grained compound. Coarse-grained compounds have a smaller grain-size number and could damage the paint. After polishing with a compound, coat with wax to restore the original luster. Frequent polishing with a compound or an incorrect polishing technique will result in removing the paint layer and exposing the undercoat. When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list.

CAUTION

Do not use any agents with organic

Black plate (395,1)

Appearance care 10-3

solvents on the surface of the bulb assembly cover. However, if a polish or wax with organic solvents is applied to the cover surface, com- pletely wipe off the polish or wax. Otherwise, the cover surface may be damaged.

NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.

& Cleaning aluminum wheels . Promptly wipe the aluminum wheels clean of any kind of grime or agent. If dirt is left on too long, it may be difficult to clean off. . Do not use soap containing grit to clean the wheels. Be sure to use a neutral cleaning agent, and later rinse thoroughly with water. Do not clean the wheels with a stiff brush or expose them to a high-speed washing device. . Clean the vehicle (including the alumi- num wheels) with water as soon as possible when it has been splashed with sea water, exposed to sea breezes, or driven on roads treated with salt or other agents.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

10

10-4 Appearance care

Corrosion protection

Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable operation.

& Most common causes of

corrosion

The most common causes of corrosion are: 1. The accumulation of moisture retain- ing dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor accidents.

Corrosion is accelerated on the vehicle when: 1. is exposed to road salt or dust It control chemicals, or used in coastal areas where there is more salt in the air, or in areas where there is considerable industrial pollution. 2. It is driven in areas of high humidity, especially when temperatures range just above freezing. 3. Dampness in certain parts of the vehicle remains for a long time, even

though other parts of the vehicle may be dry. 4. High temperatures will cause corro- sion to parts of the vehicle which cannot dry quickly due to lack of proper ventila- tion.

& To help prevent corrosion Wash the vehicle regularly to prevent corrosion of the body and suspension components. Also, wash the vehicle promptly after driving on any of the following surfaces. . roads that have been salted to prevent them from freezing in winter . mud, sand, or gravel . coastal roads

After the winter has ended, it is recom- mended that the underbody be given a very thorough washing.

Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steering system, floor pan, and fenders. If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need

Black plate (396,1)

assistance.

Repair chips and scratches in the paint as soon as you find them.

Check the interior of the vehicle for water and dirt accumulation under the floor mats because that could cause corrosion. Occasionally check under the mats to make sure the area is dry. Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated garage. In such a garage, corrosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.

If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, trunk lid lock, and hood latch should be inspected and lubricated periodically.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Cleaning the interior

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. (Do not use organic solvents.)

& Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft brush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and luke- warm water then dry thoroughly.

the stain does not come out,

try a If commercially-available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instruc- tions.

CAUTION

When cleaning the seat, do not use benzine, paint thinner, or any similar materials.

& Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended the seats and head restraints be that covered, or to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a commercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of genuine leather.

the windows shaded,

Black plate (397,1)

Appearance care 10-5

& Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials may be used when necessary.

CAUTION

Strong cleaning agents such as solvents, paint thinners, window cleaner or fuel must never be used on leather or synthetic interior ma- terials. Doing so could damage the surface and cause the color to deteriorate.

& Climate control panel, audio

panel, instrument panel, console panel, and switches Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

10

Black plate (398,1)

10-6 Appearance care

CAUTION

. Do not use organic solvents such as paint thinners or fuel, or strong cleaning agents that con- tain those solvents.

. Do not use chemical solvents that contain silicone on the vehi- cle audio system, electrical com- ponents of the air-conditioner or any switches. If silicone adheres to these parts, it may cause damage to electrical compo- nents.

& Monitor (if equipped) To clean the audio/navigation monitor, wipe it with a silicone cloth or with a soft cloth. the monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent.

If

CAUTION

. Do not spray neutral detergent directly onto the monitor. Doing so could damage the monitor’s components.

. Do not wipe the monitor with a hard cloth. Doing so could scratch the monitor.

. Do not use cleaning fluid that contains thinner, fuel, or any other volatile substance. Such cleaning fluid could erase the lettering on the switches at the bottom of the monitor.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Maintenance schedule ....................................... 11-3
Maintenance precautions................................... 11-3

Before checking or servicing in the engine

compartment....................................................

11-4

When checking or servicing in the engine

compartment while the engine is running..........

Cooling fan, hose and connections................... Engine coolant .................................................

Checking the oil level ......................................... Changing the oil and oil filter.............................. Recommended grade and viscosity .................... Synthetic oil.....................................................

11-4
Engine hood ....................................................... 11-5
Engine compartment overview.......................... 11-6
Engine oil............................................................ 11-7
11-7
11-8
11-9
11-10
Cooling system ................................................ 11-10
11-10
11-11
Air cleaner element .......................................... 11-12
11-12
Spark plugs ...................................................... 11-13
11-13
Drive belts ........................................................ 11-14
Manual transmission oil .................................. 11-14
11-14
Continuously variable transmission fluid....... 11-14
Front differential gear oil (CVT models) ......... 11-15
11-15
Rear differential gear oil .................................. 11-15
11-15
Brake fluid ........................................................ 11-15
11-15

Recommended grade and viscosity ..................

Recommended grade and viscosity ..................

Recommended grade and viscosity ..................

Replacing the air cleaner element .....................

Recommended spark plugs ..............................

Checking the fluid level ....................................

Black plate (21,1)

Maintenance and service

Recommended brake fluid ............................... Clutch fluid (MT models)................................. Checking the fluid level.................................... Recommended clutch fluid............................... Brake booster .................................................. Brake pedal ...................................................... Checking the brake pedal free play .................. Checking the brake pedal reserve distance....... Clutch pedal (MT models) ............................... Checking the clutch function............................ Checking the clutch pedal free play.................. Hill start assist system (MT models).............. Replacement of brake pad and lining ............ Breaking-in of new brake pads and linings ....... Parking brake stroke ....................................... Tires and wheels.............................................. Types of tires................................................... Tire pressure monitoring system (TPMS) (if

equipped) ...................................................... Tire inspection................................................. Tire pressures and wear .................................. Wheel balance ................................................. Wear indicators ............................................... Tire rotation direction mark .............................. Tire rotation..................................................... Tire replacement.............................................. Wheel replacement .......................................... Aluminum wheels ............................................ Windshield washer fluid.................................. Replacement of wiper blades .........................

11-16
11-16
11-16
11-17
11-17
11-18
11-18
11-18
11-19
11-19
11-19
11-19
11-20
11-20
11-21
11-21
11-21

11-21
11-23
11-23
11-25
11-25
11-26
11-26
11-27
11-27
11-28
11-28
11-30

11

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Maintenance and service

11-30

Windshield wiper blade assembly ..................... Windshield wiper blade rubber (type A and type B) .................................................................. Rear window wiper blade assembly .................. Rear window wiper blade rubber.......................

11-31
11-32
11-33
Battery............................................................... 11-34
Fuses ................................................................ 11-35
Main fuse .......................................................... 11-36
Installation of accessories............................... 11-37
Replacing bulbs ............................................... 11-37
11-37

Headlights (models with HID headlights) ...........

Black plate (22,1)

Headlights (models without HID headlights)...... Front turn signal light ...................................... Parking light .................................................... Front fog light (if equipped).............................. Rear combination lights ................................... License plate light ........................................... Map light ......................................................... Dome light and cargo area light ....................... Trunk light ....................................................... High-mounted stop light (4-door)...................... Other bulbs .....................................................

11-37
11-39
11-39
11-39
11-39
11-42
11-43
11-43
11-44
11-44
11-45

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Maintenance schedule

Maintenance precautions

The scheduled maintenance items re- quired to be serviced at regular intervals are shown in the “Warranty and Main- tenance Booklet”.

For details of your maintenance schedule, read the separate “Warranty and Main- tenance Booklet”. NOTE For models with a multi function dis- play, you can set a reminder to be displayed when a scheduled mainte- nance item is almost due. For details, refer to “Maintenance settings” F3-52.

When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer.

If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.

Incorrect or incomplete service could cause improper or unsafe vehicle opera- tion. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage.

WARNING

. Always select a safe area when performing maintenance on your vehicle.

. Always be very careful to avoid injury when working on the vehi- cle. Remember that some of the materials in the vehicle may be hazardous if improperly used or handled, for example, battery acid.

. Your vehicle should only be ser- viced by persons fully competent to do so. Serious personal injury

Black plate (403,1)

Maintenance and service 11-3

may result to persons not experi- enced in servicing vehicles.

. Always use the proper tools and make certain that they are well maintained.

. Never get under the vehicle sup- ported only by a jack. Always use safety stands to support the vehicle.

. Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas.

. Do not smoke or allow open flames around the fuel or battery. This will cause a fire.

. Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer.

in your eyes,

. Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get thoroughly wash them out with clean water. . Do not tamper with the wiring of the SRS airbag system or seat- belt pretensioner system, or at- tempt to take its connectors apart, as that may activate the system or it can render it inop-

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11

11-4 Maintenance and service

erative. NEVER use a circuit tester for this wiring. If your SRS airbag or seatbelt preten- sioner needs service, consult your nearest SUBARU dealer.

on a vehicle equipped with a remote engine start system (a dealer option) temporarily place that system in the service mode to prevent it from unexpectedly starting the engine.

& Before checking or servicing

in the engine compartment

WARNING

. Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.

. Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine has stopped.

. Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire.

. Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped.

. Before performing any servicing

CAUTION

Do not contact the drive belt cover while checking the components in the engine compartment. Doing so may cause your hand to slip off the cover and result in an unexpected injury.

Black plate (404,1)

& When checking or servicing in the engine compartment while the engine is running

WARNING

A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, drive belt and any other moving engine parts. Removing rings, watches and ties is advisable.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Engine hood

To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original position.

3. Release the secondary hood release by moving the lever between the front grille and the hood toward the left.

2. Pull the hood release knob under the instrument panel.

Black plate (405,1)

Maintenance and service 11-5

To close the hood: 1. Lift the hood slightly and remove the hood prop from the slot in the hood and return the prop to its retainer. 2. Lower the hood to a height of approxi- mately 5.9 in (15 cm) above its closed position and then let it drop. 3. After closing the hood, be sure the hood is securely locked.

If this does not close the hood, release it from a slightly higher position. Do not push the hood forcibly to close it. It could deform the metal.

WARNING

Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily in- jury.

11

4. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11-6 Maintenance and service

Engine compartment overview

Black plate (406,1)

1) Brake fluid reservoir/Clutch fluid reservoir

(MT) (page 11-15) Fuse box (page 11-35)

2) 3) Battery (page 11-34) 4) Windshield washer tank (page 11-28) 5) Engine oil filler cap (page 11-7) 6) Engine coolant reservoir (page 11-11) 7) Radiator cap (page 11-11) 8) Engine oil level gauge (page 11-7) 9) Air cleaner case (page 11-12)

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Engine oil

NOTE . The engine oil consumption rate is not stabilized, and therefore cannot be determined until the vehicle has tra- veled at least several thousand miles (kilometers). Even after break-in, when the vehicle is used under severe driv- ing conditions such as those men- tioned in the Warranty and Mainte- nance Booklet, engine oil is consumed or deteriorated more quickly than un- der normal driving conditions. If you drive your vehicle under these severe conditions, you should check the oil level at least at every second fuel fill-up time, and change the oil more fre- quently. Please refer to the Warranty and Maintenance Booklet for more de- tails. . If the oil consumption rate seems abnormally high after the break-in period, for example more than 1 quart per 1,200 miles or 1 liter per 2,000
kilometers, contact your SUBARU deal- er.

level at each fuel

& Checking the oil level Check the engine oil stop. 1. Park the vehicle on a level surface and stop the engine. If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level.

1) Oil level gauge 2) Oil filler cap 3) Oil filter

2. Pull out the level gauge, wipe it clean, and insert it again. 3. Be sure the level gauge is correctly inserted until it stops.

Black plate (407,1)

Maintenance and service 11-7

Full level Low level

1) 2) 3) Approximately 1.1 US qt (1.0 liter, 0.9

Imp qt) from low level to full level

4. Pull out the level gauge again and check the oil level on it. If it is below the low level, add engine oil to bring the level up to the full level.

CAUTION

11

. Be careful not to touch the en- gine oil filter when removing the oil filler cap. Doing so may result in a burn, a pinched finger, or may cause some other injury.

. Use only engine oil with the recommended grade and vis- cosity.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11-8 Maintenance and service

. Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust pipe, be sure to wipe it off.

. If the level gauge is not pulled out easily, twist the level gauge right and left, then pull it out. Other- wise, you may be injured acci- dentally straining yourself.

the oil

To add engine oil, remove the engine oil filler cap and slowly pour engine oil through the filler neck. After pouring oil into the engine, you must use the level gauge to confirm that is correct. NOTE To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold. & Changing the oil and oil filter

level

CAUTION

If you change your own oil, be sure to drain all the oil from the filter before disposal. Do not dispose of used engine oil by placing it in the

trash, or by pouring it onto the ground, into sewers, or into any body of water. Check with your local government office for the proper disposal options available to you.

Change the oil and oil filter according to the maintenance schedule in the “War- ranty and Maintenance Booklet”. filter must be The engine oil and oil changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold weather. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.

Black plate (408,1)

4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of properly.

WARNING

Be careful not to burn yourself with hot engine oil.

5. Wipe the seating surface of the drain plug with a clean cloth and tighten it securely with a new sealing washer after the oil has completely drained out.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Oil filter color Part number

Black

15208AA160

Amount of

rotation 1 rotation

CAUTION

. Never over tighten the oil filter because that can result in an oil leak.

. Thoroughly wipe off any engine oil that has spilled over the exhaust pipe and/or under-cover. If spilled oil is not promptly wiped up, the oil could cause a fire.

10. Pour engine oil through the filler neck. For the oil capacity (guideline), refer to “Engine oil” F12-4. The oil quantity indicated above is only guideline. The necessary quantity of oil depends on the quantity of oil that has been drained. The quantity of drained oil differs slightly depending on the temperature of the oil and the time the oil is left flowing out. After refilling the engine with oil, therefore, you must use the level gauge to confirm that the level is correct. 11. Start the engine and make sure that no oil leaks appear around the filter’s rubber

Black plate (409,1)

Maintenance and service 11-9

seal and drain plug. 12. Run the engine until it reaches the normal operating temperature. Then stop the engine and wait a few minutes to allow the oil drain back. Check the oil level again and if necessary, add more engine oil.

CAUTION

Be careful not to spill engine oil If oil touches the when adding it. exhaust pipe, it may cause a bad smell, smoke, and/or a fire.

& Recommended grade and

viscosity

CAUTION

Use only engine oil with the recom- mended grade and viscosity.

Refer to “Engine oil” F12-4.

11

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

6. Remove the oil filter with an oil filter wrench. 7. Before installing a new oil filter, apply a thin coat of engine oil to the seal. 8. Clean the rubber seal seating area of the engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 9. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the seating sur- face.

11-10 Maintenance and service

NOTE Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the en- gine.

& Synthetic oil You should use synthetic engine oil that meets the same requirements given for conventional engine oil. When using synthetic oil, you must use oil of the same classification, viscosity and grade shown in this Owner’s Manual. Refer to “Engine oil” F12-4. Also, you must follow the oil and filter changing intervals shown in the Warranty and Maintenance booklet. NOTE Synthetic oil of the grade and viscosity noted in chapter 12 is the recom- mended engine oil for optimum engine performance. Conventional oil may be used if synthetic oil is unavailable.

Black plate (410,1)

Cooling system

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

CAUTION

. Vehicles are filled at the factory with SUBARU Super Coolant that does not require the first change for 11 years/137,500 miles (11
years/220,000 km). This coolant should not be mixed with any other brand or type of coolant during this period. Mixing with a different coolant will reduce the life of the coolant. Should it be necessary to top up the coolant f o r a n y r e a s o n , u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is

shortened to that of the mixing coolant.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

& Cooling fan, hose and con-

nections

Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific temperature.

If the radiator cooling fan does not operate even when the coolant temperature high warning light blinks or illuminates in RED, the cooling fan circuit may be defective. Refer to “Coolant temperature low indica- tor light/Coolant temperature high warning light” F3-13. Check the fuse and replace it if necessary. Refer to “Fuses” F11-35 and “Fuse panel located in the engine compartment” F12- 11. If the fuse is not blown, have the cooling system checked by your SUBARU dealer.

If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system. It is recommended that

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

the cooling system and connections be checked for leaks, damage, or looseness.

& Engine coolant ! Checking the coolant level

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

Black plate (411,1)

Maintenance and service 11-11

1)

Fill up to this level

1) 2)

“FULL” level mark “LOW” level mark

Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, remove the radiator cap and refill coolant up to just below the filler neck as shown in the following illustration.

11

3. After refilling the reserve tank and the radiator, reinstall the cap and check that the rubber gaskets inside the radiator cap are in the proper position.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11-12 Maintenance and service

CAUTION

Air cleaner element

. Be careful not

to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

! Changing the coolant It may be difficult to change the coolant. Have the coolant changed by your SUBARU dealer if necessary.

The coolant should be changed according to the maintenance schedule in the “Warranty and Maintenance Booklet”.

WARNING

Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. the air cleaner element installed when the engine backfires, you could be burned.

is not

If

CAUTION

When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.

The air cleaner element functions as a filter screen. When the element is perfo- rated or removed, engine wear will be excessive and engine life shortened.

It is not necessary to clean or wash the air cleaner element.

Black plate (412,1)

& Replacing the air cleaner

element

Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts.

1) Clamp 2) Air intake boot 3) Clip

the air

intake boot out of

1. Loosen the screw on the clamp and pull the air cleaner case. 2. Unsnap the two clips holding the air cleaner case cover.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

the three projections on the air cleaner case into the slits on the air cleaner case cover. 6.

Install in the reverse order of removal.

3. Open the air cleaner case and remove the air cleaner element. 4. Clean the inside of the air cleaner case and case cover with a damp cloth and install a new air cleaner element.

5. To install the air cleaner case, insert

Black plate (413,1)

Maintenance and service 11-13

Spark plugs

It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer.

The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.

CAUTION

Make sure the cables are replaced in the correct order.

& Recommended spark plugs For the recommended spark plugs, refer to “Electrical system” F12-7.

11

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (414,1)

11-14 Maintenance and service

Drive belts

Manual transmission oil

It is unnecessary to check the deflection of the drive belt periodically because your engine is equipped with an automatic belt tension adjuster. However, replacement of the belt should be done according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If the drive belt is loose, cracked or worn, contact your SUBARU dealer.

level. Check that

It is not necessary to check the transmis- sion oil there are no cracks, damage or leakage. However, the oil inspection should be performed ac- cording to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for details.

& Recommended grade and

viscosity

Continuously variable trans- mission fluid

It is not necessary to check the transmis- sion fluid level. Check that there are no cracks, damage or leakage. However, the fluid inspection should be performed according to the maintenance schedule in the “Warranty and Maintenance Book- let”. Consult your SUBARU dealer for details.

Each oil manufacturer has its own base oils and additives. Never use different brands together. For details, to “Manual front differential and rear differential gear oil” F12-6.

transmission,

refer

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Front differential gear oil (CVT models)

leakage. However,

It is not necessary to check the gear oil level. Check that there are no cracks, damage or the oil inspection should be performed according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for details.

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together. For details, to “Manual front differential and rear differential gear oil” F12-6.

transmission,

refer

Rear differential gear oil

leakage. However,

It is not necessary to check the gear oil there are no cracks, level. Check that damage or the oil inspection should be performed according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for details.

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together. For details, to “Manual front differential and rear differential gear oil” F12-6.

transmission,

refer

Black plate (415,1)

Maintenance and service 11-15

Brake fluid & Checking the fluid level

WARNING

to your eyes.

. Never let brake fluid contact your eyes because brake fluid can be harmful If brake fluid gets in your eyes, immedi- ately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable.

. Brake fluid absorbs moisture from the air. Any absorbed moist- ure can cause a dangerous loss of braking performance.

. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

CAUTION

. When adding brake fluid, be care- ful not to allow any dirt into the reservoir.

. Never splash the brake fluid over painted surfaces or rubber parts. – CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11

11-16 Maintenance and service

Alcohol contained in the brake fluid may damage them.

. Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off.

check the fluid level for the brake system at the front part of the reservoir (shaded area in the illustration). If the fluid level is below “MIN”, add the recommended brake fluid to “MAX”. Use only brake fluid from a sealed container.

& Recommended brake fluid Refer to “Fluids” F12-7.

CAUTION

Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand.

“MAX” level line “MIN” level line

1) 2) A) The brake fluid level must be checked in

this area.

Check the fluid level monthly. Check the fluid level on the outside of the reservoir. Because this reservoir is used for both the brake and clutch systems and has chambers for each system, be sure to

Black plate (416,1)

Clutch fluid (MT models) & Checking the fluid level

WARNING

Never let clutch fluid contact your eyes because clutch fluid can be harmful to your eyes. If clutch fluid gets in your eyes, immediately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable.

CAUTION

. Clutch fluid absorbs moisture from the air. Any absorbed moist- ure can cause improper clutch operation.

. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

. When clutch fluid is added, be careful not to allow any dirt into the tank.

. Never splash the clutch fluid over painted surfaces or rubber parts.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Alcohol contained in the clutch fluid may damage them.

. Be careful not to spill clutch fluid when adding it. If clutch fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If clutch fluid gets on the exhaust pipe, be sure to wipe it off.

. The fluid level

for the clutch system must be checked at the inboard side of the reservoir. It cannot be checked at the out- board side of the reservoir.

Check the fluid level monthly. Check the fluid level on the outside of the reservoir. Because this reservoir is used for both the brake and clutch systems and has chambers for each system, be sure to check the fluid level for the clutch system at the reservoir (shaded area in the illustration). If the fluid is below “MIN”, add the recom- level mended clutch fluid to “MAX”. Use only clutch fluid from a sealed container.

the inboard side of

& Recommended clutch fluid Refer to “Fluids” F12-7.

CAUTION

Never use different brands of clutch fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand.

“MAX” level line “MIN” level line

1) 2) A) The clutch fluid level must be checked in

this area.

Black plate (417,1)

Maintenance and service 11-17

Brake booster

If the brake booster does not operate as described in the following, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary. 2. With the brake pedal depressed, start the engine. The pedal should move slightly down to the floor. 3. With the brake pedal depressed, stop the engine and keep the pedal depressed for 30 seconds. The pedal height should not change. 4. Start the engine again and run for approximately one minute then turn it off. Depress the brake pedal several times to check the brake booster. The brake booster operates properly if the pedal stroke decreases with each depression.

NOTE For vehicles equipped with the brake assist system, when you depress the brake pedal strongly or suddenly, the following phenomena occur. However, even though these occur, they do not indicate any malfunctions, and the brake assist system is operating prop-

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

11

Black plate (418,1)

& Checking the brake pedal