pressure, replacement of the fuel filter should be performed only by your SUBARU dealer.
. Wear adequate eye protection to
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
11-4 Maintenance and service
in your eyes,
guard against getting oil or fluids in your eyes. If something does get thoroughly wash them out with clean water. . Do not tamper with the wiring of the SRS airbag system or seat- belt pretensioner system, or at- tempt to take its connectors apart, as that may activate the system or it can render it inop- erative. The wiring and connec- tors of these systems are yellow for easy identification. NEVER use a circuit tester for this wiring. If your SRS airbag or seatbelt pretensioner needs service, con- sult your nearest SUBARU deal- er.
& Before checking or servicing
in the engine compartment
WARNING
. Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
. Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine is stopped.
. Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire.
. Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped.
. Before performing any servicing on a vehicle equipped with a remote engine start system (a dealer option) temporarily place that system in the service mode to prevent it from unexpectedly starting the engine.
Black plate (302,1)
& When you do checking or
servicing in the engine com- partment while the engine is running
WARNING
A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Engine hood
To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original position.
2. Pull the hood release knob under the instrument panel.
Black plate (303,1)
Maintenance and service 11-5
WARNING
Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily in- jury.
3. Release the secondary hood release by moving the lever between the front grille and the hood toward the left. 4. Lift up the hood.
To close the hood: 1. Lower the hood to a height of approxi- mately 5.9 in (15 cm) above its closed position and then let it drop. 2. After closing the hood, be sure the hood is securely locked.
If this does not close the hood, release it from a slightly higher position. Do not push the hood forcibly to close it. It could deform the metal.
11
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-6 Maintenance and service
Engine compartment overview & Non-turbo models
Black plate (304,1)
1) Power steering fluid reservoir (page 11-
24)
2) Manual transmission oil level gauge (MT) (page 11-19) or Differential gear oil level gauge (AT) (page 11-21)
3) Clutch fluid reservoir (page 11-26) 4) Automatic transmission fluid level gauge
(page 11-20)
Fuse box (page 11-44)
5) Brake fluid reservoir (page 11-25) 6) 7) Battery (page 11-43) 8) Windshield washer tank (page 11-38) 9) Engine oil filler cap (page 11-8) 10) Engine coolant reservoir (page 11-13) 11) Radiator cap (page 11-13) 12) Engine oil level gauge (page 11-8) 13) Air cleaner element (page 11-15)
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Turbo models
Black plate (305,1)
Maintenance and service 11-7
1) Power steering fluid reservoir
(page 11-24)
2) Manual transmission oil level gauge (MT) (page 11-19) or differential gear oil level gauge (AT) (page 11-21)
3) Clutch fluid reservoir (page 11-26) 4) Automatic transmission fluid level gauge
(page 11-20)
Fuse box (page 11-44)
5) Brake fluid reservoir (page 11-25) 6) 7) Battery (page 11-43) 8) Windshield washer tank (page 11-38) 9) Engine oil filler cap (page 11-8) 10) Engine coolant reservoir (page 11-13) 11) Engine oil level gauge (page 11-8) 12) Radiator cap (page 11-13) 13) Air cleaner element (page 11-15)
11
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-8 Maintenance and service
Engine oil
NOTE
. The engine oil consumption rate is
not stabilized, and therefore cannot be
determined until the vehicle has tra-
veled at least several thousand miles
(kilometers). Even after break-in, when
the vehicle is used under severe driv-
ing conditions such as those men-
tioned in the Warranty and Mainte-
nance Booklet, engine oil is consumed
or deteriorated more quickly than un-
der normal driving conditions.
If you
drive your vehicle under these severe
conditions, you should check the oil
level at least at every second fuel fill-up
time, and change the oil more fre-
quently. Please refer to the Warranty
and Maintenance Booklet for more de-
tails.
. If the oil consumption rate seems
abnormally high after the break-in
period, for example more than 1 quart
per 1,200 miles or 1 liter per 2,000
kilometers, contact your SUBARU deal-
er.
& Checking the oil level Check the engine oil stop. 1. Park the vehicle on a level surface and stop the engine.
level at each fuel
2. Pull out the level gauge that has the “ ” symbol on top, wipe it clean, and insert it again. 3. Be sure the level gauge is correctly inserted until it stops.
Black plate (306,1)
1) Notch 2) Upper level Lower level 3)
4. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.
CAUTION
. Use only engine oil with the recommended grade and vis- cosity.
. Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
pipe, be sure to wipe it off.
If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. Just after driving or while the engine is warm, the engine oil level reading may be in a range between the upper level and the notch mark. This is caused by thermal expansion of the engine oil. To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold. & Changing the oil and oil filter Change the oil and oil filter according to the maintenance schedule in the “War- ranty and Maintenance Booklet”. The engine oil and oil filter must be changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold weather. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.
Black plate (307,1)
Maintenance and service 11-9
properly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wipe the seating surface of the drain plug with a clean cloth and tighten it securely with a new sealing washer after the oil has completely drained out. 6. Remove the under cover.
Turbo models
Turbo models
11
Non-turbo models
4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-10 Maintenance and service
Non-turbo models
7. Remove the oil filter with an oil filter wrench. 8. Before installing a new oil filter, apply a thin coat of engine oil to the seal. 9. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 10. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.
Oil filter color Part number
Black
15208AA100
Amount of
rotation 1 rotation
CAUTION
. Never over tighten the oil filter because that can result in an oil leak.
. Thoroughly wipe off any engine oil that has spilled over the exhaust pipe and/or under-cover. If spilled oil is not promptly wiped up, the oil could cause a fire.
11. Reinstall under cover. 12. Pour engine oil through the filler neck.
Oil capacity (guideline):
4.2 US qt (4.0 liters, 3.5 Imp qt)
The oil quantity indicated above is only guideline. The necessary quantity of oil depends on the quantity of oil that has been drained. The quantity of drained oil differs slightly depending on the temperature of the oil and the time the oil is left flowing out. After refilling the engine with oil, therefore, you
Black plate (308,1)
must use the level gauge to confirm that the level is correct. 13. Start the engine and make sure that no oil leaks appear around the filter’s rubber seal and drain plug. 14. Run the engine until it reaches the normal operating temperature. Then stop the engine and wait a few minutes to allow the oil drain back. Check the oil level again and if necessary, add more engine oil.
CAUTION
Be careful not to spill engine oil If oil touches the when adding it. exhaust pipe, it may cause a bad smell, smoke, and/or a fire.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Recommended grade and
viscosity
capabilities
Black plate (309,1)
Maintenance and service 11-11
Oil grade:
ILSAC GF-4, which can be identified with the ILSAC certification mark (Starburst mark) or API classification SM with the words “ENERGY CONSERVING”
These recommended oil grades can be identified by looking for either or both of the following marks displayed on the oil container.
API Service label 1)
Indicates the oil quality by API designa- tions Indicates the SAE oil viscosity grade Indicates that
the oil has fuel saving
2) 3)
ILSAC Certification Mark (Starburst Mark) In choosing an oil, you want the proper quality and viscosity, as well as one that will add to fuel economy. The following table lists the recommended viscosities and applicable temperatures. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU.
SAE viscosity No. and applicable tempera- ture *:
5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better in hot weather, oil of higher viscosity is required to properly lubricate the engine.
fuel economy. However,
CAUTION
Use only engine oil with the recom- mended grade and viscosity.
11
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-12 Maintenance and service
& Recommended grade and
viscosity under severe driv- ing conditions
If the vehicle is used in desert areas, in areas with very high temperatures, or is used for heavy-duty applications, use of oil with the following grade and viscosities is recommended.
API classification SM (or SL):
SAE viscosity No.: 30, 40, 10W-50,
20W-40, 20W-50
& Synthetic oil You can use synthetic engine oil that meets the same requirements given for conventional engine oil. When using synthetic oil, you must use oil of the same classification, viscosity and grade shown in this Owner’s Manual, and must follow the oil and filter changing intervals shown in the maintenance schedule.
Cooling system
WARNING
Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.
CAUTION
. Vehicles are filled at the factory
with SUBARU Super Coolant that
does not require the first change
for 11 years/137,500 miles (11
years/220,000 km). This coolant
should not be mixed with any
other brand or type of coolant
during this period. Mixing with a
different coolant will reduce the
life of the coolant. Should it be
necessary to top up the coolant
f o r a n y r e a s o n , u s e o n l y
SUBARU Super Coolant.
If the SUBARU Super Coolant is
diluted with another brand or
type, the maintenance interval is
Black plate (310,1)
shortened to that of the mixing coolant.
. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.
& Cooling fan, hose and con-
nections
Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific temperature. If the radiator cooling fan does not operate even when the coolant temperature high warning light illuminates, the cooling fan circuit may be defective. Check the fuse and replace it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU dealer.
If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Engine coolant ! Checking the coolant level
1) 2)
“FULL” level mark “LOW” level mark
Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, remove the radiator cap and refill as required.
3. After refilling the reserve tank and the radiator, reinstall the caps and check that the rubber gaskets inside the radiator cap are in the proper position.
CAUTION
. Be careful not
to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.
. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.
Black plate (311,1)
Maintenance and service 11-13
! Changing the coolant
WARNING
Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.
Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi- tioner using the following procedures according to the maintenance schedule. 1. Remove the under cover.
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
11-14 Maintenance and service
Non-turbo models 1)
Fill up to this level
2. Place a proper container under the drain plug and loosen the drain plug. 3. Loosen the radiator cap to drain the coolant from the radiator. Then drain the coolant from the reserve tank. Tighten the drain plug securely. NOTE (turbo model only) The cap (without tabs) on top of the radiator does not need to be removed. To add coolant, remove the cap (with tabs) on the coolant tank on top of the engine. 4.
Install the under cover.
Turbo models 1)
Fill up to this level
5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough
Black plate (312,1)
room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the system.
Guideline of coolant quantity (including coolant in reservoir tank):
Non-turbo models:
MT: 7.2 US qt (6.8 liters, 6.0 Imp qt) AT: 7.1 US qt (6.7 liters, 5.9 Imp qt)
Turbo models:
8.5 US qt (8.0 liters, 7.0 Imp qt)
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (313,1)
Maintenance and service 11-15
Air cleaner element
WARNING
Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. the air cleaner element installed when the engine backfires, you could be burned.
is not
If
1) 2)
“FULL” level mark “LOW” level mark
CAUTION
. Be careful not
to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.
. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.
6. Pour the coolant and fill to the reser- voir tank’s “FULL” level mark.
7. Put the radiator cap back on and tighten firmly. At this time, make sure that the rubber gasket in the radiator cap is correctly in place. 8. Start and run the engine for more than 5 minutes at 2,000 to 3,000 rpm. 9. Stop the engine and wait until the coolant cools down (122 to 1408F [50 to 608C]). If there is any loss of coolant, add coolant to the radiator’s filler neck and to the reserve tank’s “FULL” level. 10. Put the radiator cap and reservoir cap back on and tighten firmly.
CAUTION
When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.
The air cleaner element functions as a filter screen. When the element is perfo- rated or removed, engine wear will be excessive and engine life shortened.
The air cleaner element is a dry type. It is unnecessary to clean or wash the ele- ment.
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
Black plate (314,1)
11-16 Maintenance and service
& Replacing the air cleaner
element
Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. ! Non-turbo models
cleaner case. 3. Unsnap the two clips holding the air cleaner case cover.
6. To install the air cleaner case cover, insert the three projections on the air cleaner case cover into the slits on the air cleaner case and then snap the two clips on the air cleaner case cover.
4. Open the air cleaner case cover and remove the air cleaner element. 5. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element.
1) Connector 2) Clamp 3) Air intake boot 4) Clip
1. Unplug the connector that is attached to the top of the air cleaner case. 2. Loosen the screw of the clamp and pull the air
intake boot out of
the air
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
! Turbo models
to the top of the air cleaner case.
Black plate (315,1)
Maintenance and service 11-17
cover and case with a damp cloth and install a new air cleaner element.
1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct.
3. Unsnap the two clips holding the air cleaner case cover.
11
2. Unplug the connector that is attached
4. Open the air cleaner case cover and remove the air cleaner element. 5. Clean the inside of
the air cleaner
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (316,1)
11-18 Maintenance and service
Spark plugs
& Recommended spark plugs
Drive belts
Non-turbo models: FR5AP-11 (NGK)
Turbo models:
SILFR6A (NGK)
It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer.
The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.
CAUTION
. When disconnecting the spark plug cables, always grasp the spark plug cap, not the cables.
. Make sure the cables are re-
placed in the correct order.
Front side belt
1) Power steering pump pulley 2) 3) Alternator 4) Air conditioner compressor pulley 5) Rear side belt 6) Crank pulley A)
98 N (10 kgf, 22 lbf)
The alternator, power steering pump, and air conditioner compressor depend on drive belts. Satisfactory performance re- quires that belt tension be correct.
To check the tension of the front side belt, place a straightedge (ruler) across two adjacent pulleys (alternator and crank pulley) and apply a force of 22 lbs (98 N, 10 kg) midway between the pulleys by
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Manual transmission oil & Checking the oil level
using a spring scale. Belt deflection should be the amount specified. the front side belt is loose, cracked, or worn, contact your SUBARU dealer.
If
in (mm)
Deflection
New belt
0.28 – 0.35
(7.0 – 9.0)
Used belt
0.35 – 0.43
(9.0 – 11.0)
The rear side belt is a stretch-type belt, and the deflection and tension do not need to be checked. If there are cracks or wear confirmed on the belts and a squeaking sound is heard from them, contact your SUBARU dealer.
1) Yellow handle
Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again.
Black plate (317,1)
Maintenance and service 11-19
1) Upper level 2) Lower level
3. Pull out the level gauge again and check the oil level on it. If it is below the lower through the level gauge hole to bring the level up to the upper level.
level, add oil
CAUTION
Be careful not to spill manual trans- mission oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If oil gets on the exhaust pipe, be sure to wipe it off.
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
11-20 Maintenance and service
& Recommended grade and
viscosity
Each oil manufacturer has its own base oils and additives. Never use different brands together.
Oil grade:
API classification GL-5
Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the level gauge.
range,
Though the fluid level can be checked without warming up the fluid on the “COLD” is recommended to check the fluid level when the fluid is at operating temperature. ! Checking the fluid level when the
it
fluid is hot
SAE viscosity No. and applicable tempera- ture
1. Drive the vehicle several miles to raise
the temperature of the transmission fluid
up to normal operating temperature; 158
to 1768F (70 to 808C) is normal.
2. Park the vehicle on a level surface and
set the parking brake.
3. First shift the selector lever in each
position. Then shift it in the “P” position,
and run the engine at idling speed.
Black plate (318,1)
1) Yellow handle
1) HOT range 2) COLD range 3) Upper level Lower level 4)
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Recommended fluid
Use one of the following types of auto- matic transmission fluid. SUBARU ATF Type-HP IDEMITSU ATF HP
NOTE Using any non-specified type of auto- matic transmission fluid could result in damage inside the transmission. When replacing the automatic transmission fluid, be sure to use the kind specified.
4. Pull out the level gauge and check the fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended automatic transmission fluid up to the upper level.
! Checking the fluid level when the
fluid is cold
When the fluid level has to be checked without time to warm up the automatic transmission, check to see that the fluid level is between the lower level and upper level on the “COLD” range. If it is below that range, add fluid up to the upper level. Be careful not to overfill.
CAUTION
Be careful not to spill automatic transmission fluid when adding it. If automatic transmission fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If automatic transmission fluid gets on the exhaust pipe, be sure to wipe it off.
Black plate (319,1)
Maintenance and service 11-21
Front differential gear oil (AT vehicles) & Checking the oil level
1) Yellow handle
1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again.
11
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (320,1)
11-22 Maintenance and service
& Recommended grade and
viscosity
Each oil manufacturer has its own base oils and additives. Never use different brands together.
Oil grade:
API classification GL-5
Rear differential gear oil & Checking the gear oil level
1) Upper level 2) Lower level
3. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.
CAUTION
Be careful not to spill front differ- ential gear oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If oil gets on the exhaust pipe, be sure to wipe it off.
1) Filler plug 2) Drain plug
SAE viscosity No. and applicable tempera- ture
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (321,1)
it off.
. If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.
Maintenance and service 11-23
& Recommended grade and
viscosity
Each oil manufacturer has its own base oils and additives. Never use different brands together.
Oil grade:
API classification GL-5
1) Filler hole 2) Drain hole 3) Oil level
Remove the plug from the filler hole and check the oil level. The oil level should be kept even with the bottom of the filler hole. If the oil level is below the bottom edge of the hole, add oil through the filler hole to raise the level.
CAUTION
. Be careful not to spill rear differ- ential gear oil when adding it. If rear differential gear oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If rear differential gear oil gets on the exhaust pipe, be sure to wipe
SAE viscosity No. and applicable tempera- ture
11
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-24 Maintenance and service
Power steering fluid & Checking the fluid level
The power steering fluid expands greatly as its temperature rises; the fluid level differs according to fluid temperature. Therefore, tank has two different checking ranges for hot and cold fluids.
the reservoir
Check the power steering fluid level monthly. 1. Park the vehicle on a level surface, and stop the engine.
level
the oil
2. Check the fluid level of the reservoir tank. When the fluid is hot after the vehicle has been run: Check that is between “HOT MIN” and “HOT MAX” on the surface of the reservoir tank. When the fluid is cool before the vehicle is run: Check that the oil is between “COLD MIN” and “COLD MAX” on the surface of the reservoir tank. 3. than the applicable “MIN” line, add the recom- mended fluid as necessary to bring the level between the “MIN” and “MAX” line.
the fluid level
is lower
level
If
If the fluid level is extremely low, it may indicate possible leakage. Consult your SUBARU dealer for an inspection.
Black plate (322,1)
WARNING
Be careful not because the fluid may be hot.
to burn yourself
CAUTION
. When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank. And never use different brands together.
. Avoid spilling fluid when adding
it in the tank.
. Be careful not
to spill power steering fluid when adding it. If power steering fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If power steering fluid gets on the exhaust pipe, be sure to wipe it off.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Recommended fluid
Use one of the following types of auto- matic transmission fluid. SUBARU ATF Type-HP IDEMITSU ATF HP
Brake fluid & Checking the fluid level
1) 2)
“MAX” level mark “MIN” level mark
Check the fluid level monthly. Check the fluid level on the outside of the reservoir. If the level is below “MIN”, add the recommended brake fluid to “MAX”. Use only brake fluid from a sealed container.
WARNING
. Never let brake fluid contact your eyes because brake fluid can be harmful If brake fluid gets in your eyes, immedi- ately flush them thoroughly with
to your eyes.
Black plate (323,1)
Maintenance and service 11-25
clean water. For safety, when performing this work, wearing eye protection is advisable.
. Brake fluid absorbs moisture from the air. Any absorbed moist- ure can cause a dangerous loss of braking performance.
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.
CAUTION
. Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are of the same brand.
. When adding brake fluid, be care- ful not to allow any dirt into the reservoir.
. Never splash the brake fluid over painted surfaces or rubber parts. Alcohol contained in the brake fluid may damage them.
. Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
11-26 Maintenance and service
cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off.
Clutch fluid (MT vehicles) & Checking the fluid level
& Recommended brake fluid
FMVSS No. 116, fresh DOT 3 brake fluid
Check the fluid level on the outside of the reservoir. If the level is below “MIN” level mark, add the recommended clutch fluid to “MAX” level mark. Use only clutch fluid from a sealed container.
WARNING
Never let clutch fluid contact your eyes because clutch fluid can be harmful to your eyes. If clutch fluid gets in your eyes, immediately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is
Black plate (324,1)
advisable.
CAUTION
. Clutch fluid absorbs moisture from the air. Any absorbed moist- ure can cause improper clutch operation.
. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.
. Never use different brands of
clutch fluid together.
. When clutch fluid is added, be careful not to allow any dirt into the tank.
. Never splash the clutch fluid over painted surfaces or rubber parts. Alcohol contained in the clutch fluid may damage them.
. Be careful not to spill clutch fluid when adding it. If clutch fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If clutch fluid gets on the exhaust pipe, be sure to wipe it off.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
& Recommended clutch fluid
Brake booster
FMVSS No. 116, fresh DOT 3 brake fluid
If the brake booster does not operate as described in the following, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary. 2. With the brake pedal depressed, start the engine. The pedal should move slightly down to the floor. 3. With the brake pedal depressed, stop the engine and keep the pedal depressed for 30 seconds. The pedal height should not change. 4. Start the engine again and run for approximately 1 minute then turn it off. Depress the brake pedal several times to check the brake booster. The brake booster operates properly if the pedal stroke decreases with each depression.
NOTE For vehicles equipped with the brake assist system, when you depress the brake pedal strongly or suddenly, the following phenomena occur. However, even though these occur, they do not indicate any malfunctions, and the brake assist system is operating prop-
Black plate (325,1)
Maintenance and service 11-27
erly. . You might feel that the brake pedal is applied by lighter force and gener- ates a greater braking force. . You might hear clicking (knocking) sounds around brake pedal.
Brake assist is not a system that brings more braking ability to the vehicle beyond its breaking capability.
11
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11-28 Maintenance and service
Brake pedal
Check the brake pedal free play and reserve distance according to the main- tenance schedule in the “Warranty and Maintenance Booklet”.
& Checking the brake pedal
free play
& Checking the brake pedal
reserve distance
1) More than 2.56 in (65 mm)
Depress the pedal with a force of approxi- mately 66 lbs (294 N, 30 kg) and measure the distance between the upper surface of the pedal pad and the floor. When the measurement is smaller than the specification, or when the pedal does not operate smoothly, contact with your SUBARU dealer.
1)
0.02 – 0.08 in (0.5 – 2.0 mm)
Stop the engine and firmly depress the brake pedal several times. Lightly pull the brake pedal up with one finger to check the free play with a force of less than 2 lbs (10 N, 1 kg). the free play is not within proper If specification, contact your SUBARU deal- er.
Black plate (326,1)
Clutch pedal (MT vehicles)
Check the clutch pedal free play and reserve distance according to the main- tenance schedule in the “Warranty and Maintenance Booklet”.
& Checking the clutch function Check the clutch engagement and disen- gagement. 1. With the engine idling, check that there are no abnormal noises when the clutch pedal is depressed, and that shifting into 1st or reverse feels smooth. 2. Start the vehicle by releasing the pedal slowly to check that the engine and transmission smoothly couple without any sign of slippage.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (327,1)
Maintenance and service 11-29
& Checking the clutch pedal
free play
Hill start assist system (MT vehicles)
Replacement of brake pad and lining
the Hill start assist system the following
Ensure that operates properly under circumstances: 1. Stop the vehicle on an uphill grade by depressing the brake pedal and clutch pedal, with the engine running. 2. Make sure that the vehicle does not move backward even after the brake pedal is released. 3. Then make sure the vehicle starts climbing the grade by following the normal starting procedures.
If the Hill start assist system does not operate as described above, contact with your SUBARU dealer.
1)
0.16 – 0.51 in (4.0 – 13.0 mm)
Lightly press the clutch pedal down with your finger until you feel resistance, and check the free play. If the free play is not within proper specification, contact your SUBARU deal- er.
11
The right front disc brake and the right rear disc brake have audible wear indicators on the brake pads. If the brake pads wear close to their service limit, the wear indicator makes a very audible scraping noise when the brake pedal is applied.
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible.
CAUTION
If you continue to drive despite the scraping noise from the audible it will brake pad wear indicator, – CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (328,1)
11-30 Maintenance and service
result in the need for costly brake rotor repair or replacement.
range, adjust it by turning the adjusting nut located on the parking brake lever.
Parking brake stroke
Parking brake stroke:
7 – 8 notches / 44 lbs (196 N, 20 kg)
WARNING
A safe location and situation should be selected for break-in driving.
CAUTION
Pulling the parking brake lever too forcefully may cause the rear wheels to lock. To avoid this, be certain to pull the lever up slowly and gently.
& Breaking-in of new brake
pads and linings
lightly. Repeat
When replacing the brake pad or lining,
use only genuine SUBARU parts. After
replacement,
the new parts must be
broken in as follows:
! Brake pad and lining
While maintaining a speed of 30 to 40
mph (50 to 65 km/h), step on the brake
pedal
this five or more
times.
! Parking brake lining
1. Drive the vehicle at a speed of
approximately 22 mph (35 km/h).
2. With the parking brake release button
pushed in, pull
the parking brake lever
SLOWLY and GENTLY. (Pulling with a
force of approximately 33 lbs [147 N, 15
kg].)
3. Drive the vehicle for approximately
220 yards (200 meters) in this condition.
4. Wait 5 to 10 minutes for the parking
brake to cool down. Repeat this proce-
dure.
5. Check the parking brake stroke. If the
parking brake stroke is out of the specified
Check the parking brake stroke according to the maintenance schedule in the “Warranty and Maintenance Booklet”. When the parking brake is properly adjusted, braking power is fully applied by pulling the lever up seven to eight notches gently but firmly (approximately 44 lbs [196 N, 20 kg]). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle. The factory-fitted tires are all-season tires. ! All season tires All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road conditions. However all season tires do not offer as much traction performance as winter (snow) tires in heavy or loose snow or on icy roads. All season tires are identified by “ALL SEASON” and/or “M+S” (Mud & Snow) on the tire sidewall. ! Summer tires Summer tires are high-speed capability tires best suited for highway driving under dry conditions. Summer tires are inadequate for driving on slippery roads such as on snow- covered or icy roads. If you drive your vehicle on snow-covered or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to replace all four tires.
! Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads.
& Tire pressure monitoring
system (TPMS) (U.S.-spec. models)
The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low. The tire pressure monitor- ing system will activate only when the vehicle is driven. Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused by running over a sharp object).
If you adjust the tire pressures in a warm garage and will then drive the vehicle in cold outside air, the resulting drop in tire pressures may cause the low tire pressure warning light to illuminate. To avoid this problem when adjusting the tire pressures in a warm garage, inflate the tires to pressures higher than those shown on the tire placard. Specifically, inflate them by an extra 1 psi (6.9 kPa, 0.07 kgf/cm2) for every difference of 108F (5.68C) between
Black plate (329,1)
Maintenance and service 11-31
the temperature in the garage and the temperature outside. By way of example, the following table shows the required tire pressures that correspond to various out- side temperatures when the temperature in the garage is 608F (15.68C). Example: Tire size: P215/65R16 96H Standard tire pressures: Front: 30 psi (210 kPa, 2.1 kgf/cm2) Rear: 29 psi (200 kPa, 2.0 kgf/cm2) Garage temperature: 608F (15.68C)
Outside
temperature
Adjusted pressure [psi (kPa, kgf/cm2)] rear front
308F (−18C)
108F (−128C)
−108F (−238C)
33
(230, 2.3)
35
(240, 2.4)
37
(255, 2.55)
32
(220, 2.2)
34
(235, 2.35)
36
(250, 2.5)
Example: Tire size: P225/55R17 95H Standard tire pressures: Front: 32 psi (220 kPa, 2.2 kgf/cm2) Rear: 30 psi (210 kPa, 2.1 kgf/cm2) Garage temperature: 608F (15.68C)
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
11-32 Maintenance and service
Outside
temperature
308F (−18C)
108F (−128C)
−108F (−238C)
Adjusted pressure
[psi (kPa, kgf/cm2)]
front
rear
33
35
(240, 2.4)
(230, 2.3)
37
(255, 2.55)
39
(270, 2.7)
35
(240, 2.4)
37
(255, 2.55)
If the low tire pressure warning light illuminates when you drive the vehicle in cold outside air after adjusting the tire pressures in a warm garage, re-adjust the tire pressures using the method described above. Then, increase the vehicle speed to at least 20 mph (32 km/h) and check to see that the low tire pressure warning light turns off a few minutes later. If the low tire pressure warning light does not turn off, the tire pressure monitoring system may not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible.
While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up. After illumination of the low tire pressure warning light, any increase in the tire pressures caused by an increase in the outside air temperature or by an increase in the temperature in the
tires can cause the low tire pressure warning light to turn off.
System resetting is necessary when the wheels are changed (for example, a switch to snow tires) and new TPMS valves are installed on the newly fitted wheels. Have this work performed by a SUBARU dealer following wheel replace- ment.
It may not be possible to install TPMS valves on certain wheels that are on the market. Therefore, if you change the wheels (for example, a switch to snow tires), use wheels that have the same part number as the standard-equipment wheels. Without four operational TPMS valve/sensors on the wheels, the TPMS will not fully function and the warning light in the instrument panel will illuminate steadily after blinking for approximately one minute.
When a tire is replaced, adjustments are necessary to ensure continued normal operation of the tire pressure monitoring system. As with wheel replacement, there- fore, you should have the work performed by a SUBARU dealer.
Black plate (330,1)
WARNING
If the low tire pressure warning light does not illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blink- ing for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possi- ble. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. If illuminates while driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi-
this light still
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
approach the curbs as squarely as possible. Also, make sure the tires are not pressed against the curb when you park the vehicle. . If you feel unusual vibration while driving or find it difficult to steer the vehicle in a straight line, one of the tires and/or wheels may be damaged. Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected.
& Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’ service lives and is essential for good running perfor- mance. Check and, if necessary, adjust the pressure of each tire (including the spare) at least once a month (for example, during a fuel stop) and before any long journey.
mately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. the light illuminates steadily after blinking for approximately one minute, promptly contact a SUBARU dealer to have the system inspected.
If
immedi-
& Tire inspection Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Contact your SUBARU dealer ately if you find any problem. NOTE . When the wheels and tires strike curbs or are subjected to harsh treat- ment as when the vehicle is driven on a rough surface, they can suffer damage that cannot be seen with the naked eye. This type of damage does not become evident until time has passed. Try not to drive over curbs, potholes or on other rough surfaces. If doing so is unavoidable, keep the vehicle’s speed down to a walking pace or less, and
Black plate (331,1)
Maintenance and service 11-33
Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the values shown on the tire placard. The tire placard is located on the door pillar on the driver’s side.
Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the outside temperature. It is best to check tire pressure outdoors before driving the vehicle.
When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure.
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
Black plate (332,1)
. Correct evenly)
tire pressure (tread worn
. Abnormally low tire pressure (tread worn at shoulders)
11-34 Maintenance and service
NOTE
. The air pressure in a tire increases
by approximately 4.3 psi (30 kPa, 0.3
kgf/cm2) when the tire becomes warm.
. The tires are considered cold when
the vehicle has been parked for at least
3 hours or has been driven less than 1
mile (1.6 km).
WARNING
Do not let air out of warm tires to adjust pressure. Doing so will result in low tire pressure.
Incorrect tire pressures detract from con- trollability and ride comfort, and they cause the tires to wear abnormally.
Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower.
Rolling resistance is high, so fuel con- sumption is also higher.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (333,1)
Maintenance and service 11-35
. Abnormally high tire pressure (tread worn in center)
the tires. The resulting loss of vehicle control could lead to an accident.
& Wear indicators
that
& Wheel balance Each wheel was correctly balanced when your vehicle was new, but the wheels will become unbalanced as the tires become worn during use. Wheel imbalance causes the steering wheel to vibrate slightly at certain vehicle speeds and detracts from the vehicle’s straight-line stability. It can also cause steering and suspension sys- tem problems and abnormal tire wear. If you suspect the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE Loss of correct wheel alignment* causes the tires to wear on one side and reduces the vehicle’s running stability. Contact your SUBARU dealer if you notice abnormal tire wear. *: The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering perfor- mance.
is poor. Also,
the tire Ride comfort magnifies the effects of road-surface bumps and dips, possibly resulting in vehicle damage.
If the tire placard shows tire pressures for the vehicle when fully loaded, adjust the tire pressures to the values that match current loading conditions.
WARNING
Driving at high speeds with exces- sively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp in- crease in temperature could cause tread separation, and destruction of
1) New tread 2) Worn tread 3)
Tread wear indicator
Each tire incorporates a tread wear indicator, which becomes visible when the depth of the tread grooves decreases to 0.063 in (1.6 mm). A tire must be replaced when the tread wear indicator appears as a solid band across the tread.
WARNING
When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at high speeds in wet weather can
– CONTINUED –
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
11
Black plate (334,1)
11-36 Maintenance and service
cause the vehicle to hydroplane. The resulting loss of vehicle control can lead to an accident.
the direction mark facing forward.
& Tire rotation
NOTE For safety, inspect tire tread regularly and replace the tires before their tread wear indicators become visible.
& Tire rotation direction mark
Vehicles equipped with 4 non-unidirec- tional tires 1)
Front
Vehicles equipped with unidirectional tires 1)
Front
Tire wear varies from wheel to wheel. To
maximize the life of each tire and ensure
that the tires wear uniformly, it is best to
rotate the tires every 7,500 miles (12,500
km). Move the tires to the positions shown
in the illustration each time they are
rotated.
Example of tire rotation direction mark 1)
Front
the tire has the rotation direction the tire rotation direction
If specification, mark is placed on its sidewall.
When you install a tire that has the tire rotation direction mark, install the tire with
the time of
Replace any damaged or unevenly worn tires at tire rotation, adjust the tires pressures and make sure the wheel nuts are correctly tightened.
rotation. After
After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose.
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (335,1)
Maintenance and service 11-37
& Tire replacement The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbitrarily. The tires fitted as standard equipment are optimally matched to the characteristics of the vehicle and were selected to give the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a size and construction matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard.
Using tires of a non-specified size detracts from controllability, ride comfort, braking performance, speedometer accuracy and odometer accuracy. It also creates incor- rect body-to-tire clearances and inappro- priately changes the vehicle’s ground clearance.
All four tires must be the same in terms of manufacturer, brand (tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment.
For safe vehicle operation, SUBARU recommends replacing all tires at the same time.
four
WARNING
WARNING
. All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, de- gree of wear, speed symbol, load index and size. Mixing tires of different types, sizes or degrees of wear can result in damage to vehicle’s powertrain. Use of dif- ferent types or sizes of tires can also dangerously reduce con- trollability and braking perfor- mance and can lead to an acci- dent.
. Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously re- duce controllability, resulting in an accident.
Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper opera- tion and may cause the tires to rub against the wheel well housing dur- ing turns. The resulting loss of vehicle control could lead to an accident.
NOTE When any of the wheels are removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nuts after driv- ing approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque.
& Wheel replacement When replacing wheels due, for example, to damage, make sure the replacement wheels match the specifications of the wheels that are fitted as standard equip- ment. Replacement wheels are available from SUBARU dealers.
11
北米Model "A8140BE-B" EDITED: 2008/ 2/ 28
Black plate (336,1)
11-38 Maintenance and service
Aluminum wheels
Windshield washer fluid
Aluminum wheels can be scratched and damaged easily. Handle them carefully to maintain their appearance, performance, and safety. . When any of the wheels are removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nuts after driving approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque. . Never apply oil to the threaded parts, wheel nuts, or the wheel. . Never let the wheel rub against sharp protrusions or curbs. . Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. Re- member that tire chains should be placed on the front wheels only. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts