Login- Download PDF Manual
-
SRS side airbag. (cid:1) When is the SRS side airbag unlikely to deploy?
1-68
1
Seat, seatbelt and SRS airbags
1) The vehicle is involved in an ob-
lique side-on impact.
2) The vehicle is involved in a side-on impact in an area outside the vicin- ity of the passenger compartment.
3) The vehicle strikes a telephone
pole or similar object.
4) The vehicle is involved in a side-on
impact from a motorcycle.
5) The vehicle rolls onto its side or
roof.
US1568BB
– CONTINUED –
1-69
Seat, seatbelt and SRS airbags
There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of accidents like those illustrated, the SRS side airbag may not deploy depending on the level of accident forces involved.
(cid:1) When will the SRS side airbag not deploy?
US1569BB
1) The vehicle is involved in frontal collision with another
vehicle (moving or stationary).
2) The vehicle is struck from behind.
1-70
The SRS side airbag is basically not designed to de- ploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are il- lustrated.
vated on the second.
SRS airbag system monitors
Seat, seatbelt and SRS airbags
HS1102BB
HS1103BA
1) First impact 2) Second impact
In an accident where the vehicle is struck from the side more than once, the SRS side airbag deploys only once.
Example: In the case of a double side impact collision, first with one vehicle and immediately followed by an- other from the same direction, once the SRS side air- bag is activated on the first impact, it will not be acti-
A diagnostic system continually monitors the readi- ness of the SRS airbag system while the vehicle is be- ing driven. The SRS airbag system warning light “AIR- BAG” will show normal system operation by lighting for about 6 seconds when the ignition key is turned to the “ON” position.
The following components are monitored by the indi- cator: Front sub sensor (Right hand side) Front sub sensor (Left hand side)
– CONTINUED –
1-71
Seat, seatbelt and SRS airbags
Airbag control module (including impact sensors) Frontal airbag module (Driver’s side) Frontal airbag module (Passenger’s side) Side airbag sensor (Driver’s side) Side airbag sensor (Passenger’s side) Side airbag module (Driver’s side) Side airbag module (Passenger’s side) Seatbelt pretensioner (Driver’s side) Seatbelt pretensioner (Passenger’s side) All related wiring
In the event of a malfunction indicated by any of follow- ing, the vehicle should be taken promptly to your near- est SUBARU dealer to have the system checked. Un- less checked and repaired, the SRS airbags will not function reliably: Flashing or flickering of the indicator light. No illumination of the warning light when the ignition switch is first turned to the “ON” position. Continuous illumination of the warning light. Illumination of the warning light while driving.
SRS airbag system servicing
When discarding an airbag module or scrap- ping the entire car damaged by a collision, con-
1-72
sult your SUBARU dealer. The SRS airbag has no user-serviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your nearest SUBARU dealer. Tampering with or disconnecting the system’s wiring could re- sult in accidental inflation of the SRS airbag or could make the system inoperative, which may result in serious injury. The wiring harnesses of the SRS airbag system are covered with yellow insulation and system connectors are yellow for easy identification.
If you need service or repair in areas listed be- low, we recommend that you have an autho- rized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas. Under the center console Near the bottom of the radiator Steering wheel and column and nearby areas Top of the dashboard on front passenger’s side and nearby areas
Each front seat and nearby area (for vehicles with SRS side airbags only) Inside each center pillar
In the event that the SRS airbag is deployed, re- placement of the system should be performed only by an authorized SUBARU dealer. When the components of the SRS airbag system are re- placed, use only genuine SUBARU parts.
To ensure their long-term reliability, the SRS airbags must be inspected by a SUBARU dealer ten years af- ter the date of manufacture, which is shown on the cer- tification plate attached to the driver’s door jamb. NOTE In the following cases, contact your SUBARU deal- er as soon as possible. The front part of the vehicle was involved in an accident in which the SRS frontal airbags did not deploy. The pad section of the steering wheel or front passenger’s frontal airbag cover is scratched, cracked, or otherwise damaged. In addition, if your vehicle is equipped with SRS side airbags, contact your SUBARU dealer as soon as possible in the following cases.
Seat, seatbelt and SRS airbags
Either center pillar or a nearby area of the vehi- cle was involved in an accident in which the SRS side airbag did not deploy. The fabric or leather of either front seatback is cut, frayed, or otherwise damaged.
Precautions against vehicle modifica-
tion
To avoid accidental activation of the system or rendering the system inoperative, which may result injury, no modifications should be made to any components or wiring of the SRS airbag system. This includes following modifications:
in serious
Installation of custom steering wheels Attachment of additional trim materials to the dashboard Installation of custom seats (for vehicles with SRS side airbags only) Replacement of seat fabric or leather (for vehicles with SRS side airbags only) Installation of additional fabric or leather on the front seat (for vehicles with SRS side airbags only)
– CONTINUED –
1-73
Always consult your SUBARU dealer if you want to in- stall any accessory parts to your vehicle.
Seat, seatbelt and SRS airbags
Installation of additional electrical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could inter- fere with proper operation of the SRS airbag system.
Do not perform any of the following modifica- tions. Such modifications can interfere with proper operation of the SRS airbag system. Attachment of any equipment (brush bar, winches, snow plow, skid plate, etc.) other than SUBARU genuine accessory parts to the front end. Modification of the suspension system or front end structure. Installation of a tire of different size and con- struction from the tires specified on the tire placard attached to the driver’s door jamb. Attachment of any equipment (side steps or side sill protectors, etc.) other than SUBARU genuine accessory parts to the side body. (for vehicles with side airbags only)
1-74
Keys and doors
Keys ............................................................... Key number ....................................................... Door locks ..................................................... Locking and unlocking from the outside ....... Locking and unlocking from the inside .......... Power door locking switches ...................... Remote keyless entry system (if equipped) Locking the doors ............................................. Unlocking the doors ......................................... Illuminated entry ............................................... Vehicle finder function ..................................... Sounding a panic alarm ................................... Selecting audible signal operation ................. Replacing the battery ....................................... Replacing lost transmitters .............................
2-2
2-2
2-3
2-3
2-4
2-5
2-6
2-7
2-7
2-8
2-8
2-8
2-8
2-9
2-10
Security system (if equipped) ...................... 2-14
2-14
2-14
2-16
2-17
2-17
Child safety locks ......................................... 2-20
Windows ........................................................ 2-21
2-21
Rear gate ........................................................ 2-24
Moonroof (if equipped) ................................. 2-26
2-26
2-26
2-26System operation .............................................. Arming the system ........................................... Disarming the system ...................................... Valet mode ......................................................... Passive arming .................................................
To open the moonroof ...................................... To close the moonroof ..................................... Anti-entrapment function .................................
Power windows .................................................
2-1
Keys and doors
Keys and doorsKeys
HS2011BB
1) Master key 2) Submaster key 3) Valet key 4) Key number plate
Three types of keys are provided for your vehicle: Master key, submaster key and valet key.
The master key and submaster key fit all locks on your vehicle. Ignition switch Driver’s door Glove box
2-2
The valet key fits only the ignition switch and driver’s door lock. You can keep the glove box locked when you leave your vehicle and valet key at a parking facil- ity.
Do not attach a large key holder or key case to either key. If it banged against your knees while you were driving, it could turn the ignition switch from the ON position to the ACC or OFF position, thereby stopping the engine.
Key number The key number is stamped on the metal plate at- tached to the key set. Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.
Door locks
Locking and unlocking from the out-
side
Keys and doors
1) Lock 2) Unlock
To lock the door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front (Driver’s side only).
Pull the outside door handle to open the unlocked door.
HS2013BB
1) Rotate the lock lever rearward. 2) Close the door.
HS2012BB
To lock the door from the outside without the key, ro- tate the lock lever rearward and then close the door.
To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK” side) and then close the door. In this case, all closed doors and the rear gate are locked at the same time.
Always make sure that all doors and the rear gate are locked before leaving your vehicle.
– CONTINUED –
2-3
Keys and doors
NOTE Make sure that you do not leave the key inside the vehicle when locking the doors from the outside without the key.
Locking and unlocking from the inside
is unlocked.
Pull the inside door handle to open an unlocked door.
Always make sure that all doors and the rear gate are closed before starting to drive.
Keep all doors locked when you drive, especial- ly when small children are in your vehicle. Along with the proper use of seat belts and child restraints, locking the doors reduces the chance of being thrown out of the vehicle in an accident. It also helps prevent passengers from falling out if a door is accidentally opened, and intrud- ers from unexpectedly opening doors and en- tering your vehicle.
HS2014BB
1) Lock 2) Unlock
To lock the door from the inside, rotate the lock lever rearward. To unlock the door from the inside, rotate the lock lever forward.
The red mark on the lock lever appears when the door
2-4
Power door locking switches
Keys and doors
NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using power door locking switches.
HS2015BB
1) Lock 2) Unlock
All doors and the rear gate can be locked and un- locked by the power door locking switches located at the driver’s side and the front passenger’s side doors.
To lock the doors, push the front side of the switch. To unlock the doors, push the rear side of the switch.
When you close the doors after you set the door locks, the doors remain locked.
– CONTINUED –
2-5
tance will vary depending on environmental condi- tions. Range may be reduced near sources of RF in- terference such as power plants and radio/television broadcasting towers.
The keyless entry system does not operate when the key is inserted in the ignition switch to prevent acci- dental lockout.
Do not expose the transmitter to severe shocks, such as those experienced as a result of dropping or throwing. Do not take the transmitter apart except when replacing the battery. Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.
Keys and doors
Remote keyless entry system (if equipped)
Two transmitters are provided for your vehicle.
The remote keyless entry system has the following functions. Locking and unlocking the doors and rear gate with- out a key Sounding a panic alarm Arming and disarming the security system (if your vehicle is equipped with an optional security system). See the next section “Security system (if equipped)” for detailed information. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The operable distance of the keyless entry system is approximately 30 feet (10 meters). However, this dis-
2-6
C
B1
B2
HS2016BB
A: LOCK/ARM button (Orange)
Press to Lock all doors. Press and Hold to activate panic alarm. Press three times in a five-second period to use vehi- cle finder function.
B: UNLOCK/DISARM button (Blue)
1) Press once to Unlock driver’s door. 2) Press a second time to Unlock all other doors and
rear gate.
C: LED
Locking the doors Briefly press the “LOCK/ARM” button (for less than two seconds) to lock all doors and rear gate. An elec-
Keys and doors
tronic chirp will sound one time and the turn signal lights will flash one time. If any of the doors or the rear gate is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors or the rear gate are not properly closed. When you close the door, it will automatically lock. NOTE If the “LOCK/ALARM” button is pressed for two seconds or longer, the panic alarm will sound. When locking the doors in normal circumstances, press the “LOCK/ALARM” button for less than two seconds. For details on the panic alarm, refer to “Sounding a panic alarm”.
Unlocking the doors Briefly press the “UNLOCK/DISARM” button (for less than two seconds) to unlock the driver’s door. An elec- tronic chirp will sound two times and the turn signal lights will flash two times. To unlock all other doors and rear gate, briefly press the “UNLOCK/DISARM” button a second time within 5 seconds. NOTE If the interval between the first and second press- es of the "UNLOCK/DISARM" button (for unlock-
– CONTINUED –
2-7
Keys and doors
ing of all of the doors and the rear gate) is extreme- ly short, the system may not respond.
the “UNLOCK/DISARM” button
Illuminated entry The interior dome light and ignition switch light will illu- minate when is pressed. These lights stay illuminated for approxi- mately 30 seconds if any of the doors or the rear gate is not opened. If the “LOCK/ARM” button is pressed before 30 sec- onds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light must be set to the middle po- sition in order for this function to operate.
Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “LOCK/ARM” button three times in a five-second peri- od will cause your vehicle’s horn to sound one time and its turn signal lights to flash three times.
Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds.
2-8
The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the re- mote is pressed, the alarm will be deactivated after ap- proximately 30 seconds.
Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If de- sired, you may turn the audible signal off. To turn the audible signal off, unlock the door by pressing the “UNLOCK/DISARM” button and then si- multaneously depress “LOCK/ARM” and “UNLOCK/ DISARM” buttons for more than two seconds. An elec- tronic chirp will sound two times and the turn signal lights will flash two times to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the door by pressing the “UNLOCK/DISARM” button and then si- multaneously depress “LOCK/ARM” and “UNLOCK/ DISARM” buttons for more than two seconds. An elec- tronic chirp will sound one time and the turn signal lights will flash one time to inform you that the audible signal has been turned on.
Replacing the battery When the transmitter battery begins to get weak, transmitter range will begin to decrease and the LED will not illuminate. Replace the battery as soon as pos- sible.
To replace the battery:
HS2017BA
1. Remove the two screws on the back of the trans- mitter case by using a phillips screwdriver. 2. Separate the case. 3. Remove the old battery from the holder.
Keys and doors
HS2018BB
1) Positive (+) side facing up
4. Replace with a new battery (Type CR2032 or equivalent) making sure to install the new battery with the positive (+) side facing up. 5. Install the back half of the transmitter case. 6. Reinstall the two screws on the back of the trans- mitter case. After the battery is replaced, the transmitter must be synchronized with the keyless entry system’s control unit. Press either the “LOCK/ARM” or “UN- LOCK/DISARM” button six times to synchronize the unit.
– CONTINUED –
2-9
To enter the programming mode:
1. Press “UNLOCK/DISARM” button to disarm the se- curity system. (If your vehicle is equipped with the op- tional security system.)
HS2016CA
Keys and doors
Do not let dust, oil or water get on or in the transmitter when replacing the battery. Be careful not to damage the printed circuit board in the transmitter when replacing the bat- tery.
Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system. (cid:0) Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmit- ter codes. The four transmitter codes may be the same or different.
2-10
Keys and doors
2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.
1) ON 2) LOCK
HS2019BB
HS2020BB
4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15
seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode. NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this proce- dures.– CONTINUED –
2-11
Keys and doors
To program the transmitters:
1. Open the driver’s door. 2. Close the driver’s door.
2-12
HS2019BC
1) Press any button.
HS2016DB
3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound two times to indicate that the transmitter has been programmed.
Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter. To exit the programming mode: 1. After all of your transmitters are programmed, re- move the key from the ignition switch. The horn will sound three times to indicate that the
system has exited the programming mode. 2. Make sure that the keyless entry system properly operates by operating each transmitter. (cid:0) Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code re- mains in the memory. For security reasons, lost trans- mitter codes should be deleted from the memory. To delete old transmitter codes, program four trans- mitter codes into the system. If you have only one cur- rent transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memo- ry. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access
Keys and doors
to your vehicle.
– CONTINUED –
2-13
Keys and doors
Security system (if equipped)
The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key.
The system can be armed and disarmed with the re- mote transmitter. The system does not operate when the key is inserted into the ignition switch.
System operation The security system will give the following alarm indi- cations when triggered: The turn signal lights will flash and the horn will sound intermittently. In addition, the starter motor will not operate. The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tam- pered with again. The alarm will continue for six times if any sensor continues to be activated.
The alarm is triggered by: Opening a door or the rear gate. Application of physical shock to the vehicle (e.g.
2-14
breaking glass or forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher levels of shock are detected and the system will go into full alarm. Ignition switch being turned on while in armed state. NOTE With the valet mode selected, the security system does not operate when the remote transmitter is used for locking and unlocking. The security sys- tem indicator light in the combination meter flash- es twice per second to show that the valet mode is selected. For details, refer to “Valet mode” in this section.
Arming the system (cid:0) To arm the system using remote transmitter 1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood is locked. 5. Close all doors and the rear gate.
2
1) Press to Arm the system. 2) Press to Disarm the system.
Keys and doors
HS2016EB
HS2021BA
Security system — indicator light
6. Briefly press the “LOCK/ARM” button (for less than two seconds). All doors and the rear gate will lock, an electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light starts flashing slowly (approximately once every two sec- onds).
If any of the doors or the rear gate is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors or the rear gate are not properly closed. When you close the door, the system will automatically arm and doors will automatically lock.
– CONTINUED –
2-15
Keys and doors
(cid:0) To arm the system using power door locking
switches
1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood is locked. 5. Close the doors and the rear gate but leave only the driver’s door or the front passenger’s door open.
HS2013CB
6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light will start flashing slowly (approximately once every two seconds) to inform you that the system
2-16
has armed. NOTE The system can be armed even if the engine hood, the windows and/or moonroofs are opened. Al- ways make sure that they are fully closed before arming the system.
Disarming the system Briefly press the “UNLOCK/DISARM” button (for less than two seconds) on the remote transmitter. The driv- er’s door will unlock, an electronic chirp will sound two times, the turn signal lights will flash two times and the indicator light will go off.
To unlock all other doors and the rear gate, briefly press the “UNLOCK/DISARM” button a second time. (cid:0) Emergency disarming If you cannot disarm the system using the transmitter (i.e. the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system with- out using the transmitter.
To disarm the system: 1. Unlock the door with the key and then open the door. 2. The alarm will sound.
3. Insert the key into the ignition switch and cycle it from the “LOCK” to the “ON” position three (3) times within 5 seconds.
Valet mode When you choose the valet mode, the security system does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors and rear gate and panic activation.
To enter the valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button depressed for more than two seconds. The security system status indicator light will continue to flash two times per sec- ond indicating that the system is in the valet mode.
To exit valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button pressed for more than two seconds. The indicator will stop flashing. NOTE If the remote transmitter is used to lock or unlock the doors while the valet mode is selected, the turn signal lights do not flash but an electronic chirp is emitted.
Keys and doors
Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically ac- complished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. (cid:0) To enter the passive mode
HS2022BA
1. Remove the side sill cover on the driver’s side.
1)Open the driver’s door. 2)Remove the two clips fastening the front portion of the cover with a screwdriver. 3)Remove the side sill cover by pulling it up.
– CONTINUED –
2-17
Keys and doors
HS2023BB
1) Connector for SRS airbag system (yellow) 2) White (1P)
2. Connect the white (1 pole) connector. 3. Turn the ignition switch from the “LOCK” to the “ON” position. 4. Install the side sill cover.
To place the system in active arming mode (remote re- quired for activation), disconnect the white connector.
low insulation and/or tape. Doing so could result in accidental inflation of the SRS airbag or could make the SRS airbag system inoperative, which may result in serious injury.
(cid:0) Arming the system 1. Turn the ignition switch to the “ON” position.
HS2024BB
1) ON 2) LOCK
Do not disconnect or tamper with any yellow connector and/or any harness covered with yel-
2. Turn the ignition switch from “ON” to “LOCK” posi- tion and remove the key from the ignition switch.
2-18
3
HS2013DB
3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the in- side door lock levers. 5. Close the doors. The system will automatically arm after one minute.
In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door locking switch is used to lock the vehicle, arming will take place immediately regardless of whether or not the passive mode has been selected.
Keys and doors
In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4
above or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.(cid:0) Disarming the system To disarm the system, briefly press the “UNLOCK/ DISARM” button on the transmitter. (cid:1) Tripped sensor identification If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the sys- tem, this indicates that the alarm was triggered. The number of times the indicator light flashes indicates what sensor caused the alarm condition.
To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to the “ON” position two times. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.
– CONTINUED –
2-19
Keys and doors
The indicator light provides the following indications. Flashing one time: Any door or the rear gate has been opened. Flashing three times: The impact sensor in the sys- tem’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected. NOTE The battery must be reconnected before the indi- cator light will flash.
To exit this mode, close the door and turn the ignition switch to the “ON” position.
2-20
Child safety locks
HS2025BB
1) Lock 2) Unlock
Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.
Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.
Keys and doors
Windows
Power windows
To avoid serious personal injury caused by en- trapment, you must do the followings. When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window. Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.
The power windows operate only when the ignition switch is in the “ON” position.
– CONTINUED –
2-21
Keys and doors
(cid:0) Driver’s side switches
(cid:1) Operating the driver’s window
HS2026BB
HS2027BB
1) Lock switch 2) For driver’s window (with one-touch auto down fea-
ture)
3) For front passenger’s window 4) For rear left window 5) For rear right window
All door windows can be controlled by the power win- dow switch cluster at the driver side door.
2-22
1) Open 2) Automatically open 3) Close
To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without hold- ing the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window half- way, pull the switch up lightly.
To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:1) Operating the passengers’ windows
HS2027CA
To open the passengers’ windows, push the appropri- ate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired position.
Keys and doors
(cid:1) Locking the passengers’ windows
US2510BB
1) Lock 2) Unlock
To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. (cid:0) Passengers’ side switches To open the window, push the switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position.
When the lock switch on the power window switch – CONTINUED –
2-23
Keys and doors
cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.
Rear gate
The rear gate can be locked and unlocked using either the keyless entry system or the power door locking switches. Refer to the “Power door locking switches” and “Re- mote keyless entry system (if equipped)” sections in this chapter.
HSB087CA
To open the rear gate, first unlock the rear gate lock then pull the outside handle up. Then, hold the rear gate and raise it as high as it will go.
2-24
Keys and doors
closed while driving.
Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.
NOTE If the rear gate cannot be unlocked due to a dis- charged battery, a fault in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release le- ver. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” in chapter 9 “In case of emergency” .
– CONTINUED –
2-25
HS2029BA
To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull down on the inside handle as shown in the illustration.
Do not attempt to shut the rear gate while holding the inside handle. Also avoid closing the rear gate by pulling on the inside handle from inside the cargo space. There is a danger of your hand being caught and injured. To prevent dangerous exhaust gas from en- tering the vehicle, always keep the rear gate
Keys and doors
Moonroof (if equipped)
HS2030BB
1) Open/close switch 2) Open 3) Close
The moonroof operates only when the ignition switch is in the “ON” position.
To open the moonroof Push and quickly release the rear part of the switch to open the moonroof. The sun shade also will be opened together with the moonroof. The moonroof will stop at a position 20 in. (50 cm) away from the fully
2-26
closed position. Push the switch again to open the moonroof completely. To stop the moonroof at a desired position, simply push the opposite side of the switch.
After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to pre- vent water drops from falling into the passenger com- partment.
To close the moonroof Push and quickly release the front part of the switch to close the moonroof. The moonroof will stop at a posi- tion 8 in. (20 cm) away from the fully closed position. Push the switch again to close the moonroof com- pletely. To stop the moonroof at a desired position, simply push the opposite side of the switch.
Anti-entrapment function When the moonroof senses an object trapped be- tween its glass and the vehicle’s roof during closure, it automatically moves back by 6 in. (15 cm) from that point and then stops. The anti-entrapment function may also be activated by a strong shock on the moon- roof even when there is nothing trapped.
NOTE For the sake of safety, it is recommended that you avoid driving with the moonroof fully opened. Driving with the moonroof fully open can cause an annoying sound to generate at high speeds. If such a condition has been encountered, use the moonroof at the initial stop position of 20 in. (50
cm). If the moonroof cannot be closed through switch operation because of system failure, it can be closed manually using a hex-head wrench. For the procedure, refer to “Moonroof – if the moon- roof cannot be closed” in Chapter 9 “In case of emergency”.Keys and doors
(cid:0) Sun shade
HS2031BA
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident.
– CONTINUED –
2-27
Keys and doors
To avoid serious personal injury caused by en- trapment, you must do the followings: Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof. Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof. Never try to check the anti-entrapment func- tion by deliberately placing part of your body in the moonroof.
Do not sit on the edge of the open moonroof. Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
2-28
Ignition switch .............................................. LOCK .................................................................. ACC .................................................................... ON ....................................................................... START ................................................................ Key reminder chime .......................................... Key interlock release (AT vehicles only) ........ Hazard warning flasher ................................ Meters and gauges ....................................... Speedometer ..................................................... Odometer/Trip meter ........................................ Tachometer ........................................................ Fuel gauge ......................................................... Temperature gauge ........................................... Ambient temperature gauge ............................ Warning and indicator lights ....................... Seatbelt warning light and chime .................... SRS airbag system warning light .................... CHECK ENGINE warning light/Malfunction
indicator lamp ................................................. Charge warning light ........................................ Oil pressure warning light ................................ AT OIL TEMPerature warning light
(for AT vehicles) ............................................. ABS warning light ............................................. Brake system warning light ............................. Door open warning lights ................................. Low fuel warning light ...................................... Front-wheel drive warning light
(for AT vehicles) ............................................. Shift position indicator (AT vehicles) .............
3-2
3-2
3-3
3-3
3-3
3-3
3-4
3-5
3-5
3-5
3-5
3-6
3-7
3-8
3-9
3-10
3-10
3-103-11
3-12
3-123-12
3-12
3-13
3-15
3-153-15
3-15Instruments and controls
Turn signal indicator lights .............................. High beam indicator light ................................. Cruise control indicator light ...........................
Headlights ......................................................... High/low beam change (dimmer) .................... Headlight flasher ............................................... Daytime running light system .........................
3-15
3-16
3-16
Clock .............................................................. 3-16
Light control switch ...................................... 3-17
3-18
3-18
3-19
3-19
Turn signal lever ........................................... 3-20
Illumination brightness control ................... 3-21
Parking light switch ...................................... 3-21
Fog light switch (if equipped) ...................... 3-22
Wiper and washer ......................................... 3-22
3-24
3-26
Windshield wiper deicer (if equipped) ........ 3-27
Rear window defogger switch ..................... 3-28
Mirrors ............................................................ 3-29
3-29
3-32
Tilt steering wheel ......................................... 3-34
Horn ................................................................ 3-35Inside mirror ...................................................... Outside mirrors .................................................
Windshield wiper and washer switches ......... Rear window wiper and washer switch ..........
3-1
Instruments and controls
Instruments and controls
Ignition switch
(cid:0) Automatic transmission vehicles
HS3014BA
The ignition switch has four positions: LOCK, ACC, ON and START.
LOCK The key can only be inserted or removed in this posi- tion. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.
3-2
HS3015BA
HS2020CA
The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. (cid:0) Manual transmission vehicles
The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.
HS2020DA
Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to
Instruments and controls
steer.
ACC In this position the electrical accessories (radio, ac- cessory power outlet, etc.) can be used.
ON This is the normal operating position after the engine is started.
START The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
Do not turn the ignition switch to the “START” position while the engine is running.
Key reminder chime The reminder chime sounds when the driver’s door
– CONTINUED –
3-3
Instruments and controls
opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ig- nition switch.
Key interlock release (AT vehicles
only)
If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using a phillips screwdriver.
HS3016BA
3-4
HS3017BA
3. Turn the ignition key while pressing the key inter- lock release lever. Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired.
Hazard warning flasher
Meters and gauges
Instruments and controls
Speedometer The speedometer shows the vehicle speed.
Odometer/Trip meter
UG3026BB
1) Trip meter 2) Odometer
This meter displays the odometer and two trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position.
– CONTINUED –
3-5
HS3019BA
The hazard warning flasher is used to warn other driv- ers when you have to park your vehicle under emer- gency conditions. The hazard warning flasher works with the ignition switch in any position.
To turn on the hazard warning flasher, push the haz- ard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
Instruments and controls
(cid:0) Odometer The odometer shows the total distance that the vehicle has been driven. (cid:0) Double trip meter
A trip meter
B trip meter
To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.
UG3027AB
1) A trip meter 2) B trip meter
The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.
3-6
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.
Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
Do not operate the engine with the pointer of the tachometer in the red zone. In this range,
fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank. NOTE
Instruments and controls
Fuel gauge
HS3022BB
1) Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ig- nition switch is in the “ACC” or “LOCK” position.
HS3023AA
” sign near the
You will see the “FUEL DOOR fuel gauge. This indicates that the fuel filler door (lid) is locat- ed on the right side of the vehicle. (cid:0) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [about 2.3 U.S. gal. (9.0 liters, 1.9 Imp. gal.]. It only operates when the ignition switch is in the “ON” position.
– CONTINUED –
3-7
Instruments and controls
NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 4.0 U.S. gal. (15 liters, 3.3 Imp. gal.).
Temperature gauge
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possi- ble. See “In case of emergency” in chapter 9.
HS3024BB
1) Normal operating range
The temperature gauge shows engine coolant temper- ature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temperature and driving conditions.
3-8
Ambient temperature gauge
When the actual ambient temperature falls outside the specified indicator range.
Instruments and controls
US3050BB
A: U.S. Spec. models B: CANADA models
The ambient temperature gauge shows the ambient temperature in a range from –22° F to 122° F (–30° C to 50° C). The gauge can give a false reading under any of the following conditions: When there is too much sun. During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately follow- ing a shutdown.
– CONTINUED –
3-9
Instruments and controls
Warning and indicator lights
Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:
Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light/Malfunction indica- tor lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light
If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair.
Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the remind- er chime will sound for about six seconds to remind the
3-10
driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off auto- matically after six seconds.
SRS airbag system warning light When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS air- bag and SRS side airbag (if equipped) and seatbelt pretensioners are in normal operation. If this light comes on while driving or remains illuminat- ed even after a period of about 6 seconds from when the ignition has been turned on, it may indicate that the SRS airbag system or SRS side airbag system (if equipped) or seatbelt pretensioner system is not work- ing properly. Contact your nearest SUBARU dealer immediately.
CHECK ENGINE warning light/
Malfunction indicator lamp
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or po- tential problem somewhere in the emission control system. (cid:0) If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control sys- tem malfunction has been detected. You should have your vehicle checked by an autho- rized SUBARU dealer immediately.
Instruments and controls
NOTE This light also comes on when the fuel filler cap is not tightened until it clicks.
If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indica- tor lamp coming on could be a loose or missing fuel fill- er cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK EN- GINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer im- mediately. (cid:0) If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the emission control system. To prevent serious damage to the emission control system, you should do the following: Reduce vehicle speed. Avoid hard acceleration. Avoid steep uphill grades. Reduce the amount of cargo, if possible. Stop towing a trailer as soon as possible.
The CHECK ENGINE warning light may stop blinking
– CONTINUED –
3-11
Instruments and controls
and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.
Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.
If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU deal- er immediately.
Oil pressure warning light If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil lev- el is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
3-12
Do not operate the engine with the oil pressure warning light on. This may cause serious en- gine damage.
AT OIL TEMPerature warning
light (for AT vehicles)
If this light comes on when the engine is running, it may indicate that the automatic transmission fluid tem- perature is too hot.
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. (cid:0) Automatic transmission control system warn-
ing
If the light flashes after the engine starts, it may indi- cate that the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.
(U.S.) ABS warning light (Canada) The ABS warning light comes on when the ignition
switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. The warning light does not come on when the ignition switch is turned to the “ON” position. The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
With a vehicle equipped with an EBD system, the ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For
Instruments and controls
further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If the warning light behavior is as described be- low, the ABS system may be considered normal. The warning light comes on right after the en- gine is started but goes out immediately, remain- ing off. The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12 km/h). The warning light comes on during driving, but it goes out immediately and remains off.
When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery volt- age and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.
Brake system warning light
(U.S.) (Canada)
Driving with the brake system warning light on is dangerous. This indicates your brake sys- tem may not be working properly. If the light re- – CONTINUED –
3-13
Instruments and controls
mains on, have the brakes inspected by a SUBARU dealer immediately. If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.
This light has the following three functions: (cid:0) Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. (cid:0) Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid res- ervoir with the ignition switch in the “ON” position and with the parking brake fully released.
If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the near- est safe place and check the brake fluid level. If the flu- id level is below the “MIN” mark in the reservoir, do not
3-14
drive the vehicle. Have the vehicle towed to the near- est SUBARU dealer for repair. (cid:0) Electronic Brake Force Distribution (EBD) sys-
tem warning (for vehicles with EBD)
The brake system warning light also illuminates if a malfunction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conventional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehicle’s motion may there- fore become somewhat harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, then restart it. 3. Release the parking brake. If both warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights come on again and stay illu- minated after the engine has been restarted, shut down the engine again, apply the parking brake, and
check the brake fluid level. 5. If the brake fluid level is not below the “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspect- ed. 6. If the brake fluid level is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair.
Door open warning lights The door open warning light comes on if any door or the rear gate is not fully closed.
Always make sure this light is out before you start to drive.
Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.3 U.S. gal. (9.0 liters, or 1.9 Imp. gal.). It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 4.0 U.S. gal. (15 liters, 3.3 Imp. gal.).
Instruments and controls
Front-wheel drive warning light
(for AT vehicles)
This light comes on when All Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes.
Shift position indicator (AT vehicles)
UG3030AA
This indicator shows the position of the shift lever.
Turn signal indicator lights These lights show the operation of the turn signal or lane change signal.
– CONTINUED –
3-15
Instruments and controls
If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
Clock
High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.
Cruise control indicator light This light comes on when the “CRUISE” main switch is pressed.
To adjust the clock, open the small article storage compartment in the dashboard with the vehicle parked in a safe place.
HS3025BA
3-16
To set the hour, press the “H” button. To set the min- utes, press the “M” button. To reset the minutes to “00” with a radio time signal, push the “Reset” button.
HS3018BA
To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.
Instruments and controls
Light control switch
The light switch operates only when the ignition switch is in the “ON” position.
To prevent battery discharge resulting from ac- cidentally leaving your lights on when your ve- hicle is parked, the light switch operates only when the ignition switch is in the “ON” posi- tion. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.
– CONTINUED –
3-17
Instruments and controls
Headlights
High/low beam change (dimmer)
HS3026BA
HS3026CA
To turn on the headlights, turn the knob on the end of the turn signal lever.
first position:
Parking lights, instrument panel illumination, tail lights and license plate light are on.
second position:
Headlights, parking lights, instrument panel illumina- tion, tail lights, and license plate light are on.
To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the in- strument panel is also on. To switch back to low beam, pull the lever back to the detent position.
3-18
Headlight flasher
more than just a few seconds.
Instruments and controls
HS3026DA
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” posi- tion.
When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on.
Do not hold the lever in the flashing position for
Daytime running light system
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
The low beam headlights will automatically come on at reduced brightness when the engine has started, un- der the following conditions: The parking brake is fully released. ” position. The light switch is in the “OFF” or “ The automatic transmission selector lever is set at other than the “P” position.
– CONTINUED –
3-19
or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.
Instruments and controls
Turn signal lever
1) Right turn 2) Left turn 3) Lane change for right 4) Lane change for left
HS3027BB
To activate the right turn signal, push the turn signal le- ver up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return af- ter cornering, return the lever to the neutral position by hand.
To signal a lane change, push the turn signal lever up
3-20
Illumination brightness control
Parking light switch
Instruments and controls
HS3028BA
HS3029BA
When the headlight switch is in the “ ” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial upward. To darken, turn the control dial downward.
” or “
The parking light switch operates regardless of the ig- nition switch position.
By pushing the front end of this switch, following lights will come on. – Parking lights – Tail lights – License plate lights
To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.
– CONTINUED –
3-21
Instruments and controls
Fog light switch (if equipped)
Wiper and washer
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
Do not operate the washer continuously for more than ten seconds, or when the washer flu- id tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. Do not operate the wipers when the wind- shield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. At-
HS3030AA
The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off. The indicator light located on the switch will illuminate when the fog lights are on.
3-22
tempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to oper- ate the defroster, windshield wiper deicer (if equipped) or rear window defogger before turn- ing on the wiper. If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper operation.
