Login- Download PDF Manual
-
(cid:121) Reduce vehicle speed. (cid:121) Avoid hard acceleration. (cid:121) Avoid steep uphill grades. (cid:121) Reduce the amount of cargo, if possible. (cid:121) Stop towing a trailer as soon as possible. The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.
(cid:132) Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU deal- er immediately.
– CONTINUED – 3-11
Instruments and controls
(cid:132) Oil pressure warning light
Do not operate the engine with the oil pressure warning light on. This may cause serious en- gine damage.
If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil lev- el is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
(cid:132) AT OIL TEMPerature warning
light (AT vehicles)
The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid tem- perature is too hot.
3-12
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. (cid:84) Automatic transmission control system warn-
ing
If the light flashes after the engine starts, it may indi- cate that the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.
(U.S.) (cid:132) ABS warning light (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. (cid:121) The warning light does not come on when the ignition switch is turned to the “ON” position.
(cid:121) The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). (cid:121) The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
NOTE If the warning light behavior is as described be- low, the ABS system may be considered normal. (cid:121) The warning light comes on right after the en- gine is started but goes out immediately, remain- ing off. (cid:121) The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12 km/h). (cid:121) The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery volt- age and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.
Instruments and controls
(cid:132) Brake system warning light
(U.S.) (Canada)
(cid:121) Driving with the brake system warning light on is dangerous. This indicates your brake sys- tem may not be working properly. If the light re- mains on, have the brakes inspected by a SUBARU dealer immediately. (cid:121) If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.
This light has the following two functions: (cid:84) Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. (cid:84) Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid res- ervoir with the ignition switch in the “ON” position and with the parking brake fully released.
– CONTINUED – 3-13
Instruments and controls
If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the near- est safe place and check the brake fluid level. If the flu- id level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the near- est SUBARU dealer for repair.
(cid:132) Door ajar warning lights The specific door ajar warning light comes on if any door is not fully closed. Always make sure this light is out before you start to drive.
(cid:132) Switchback door indicator light While the ignition switch is in the “ON” position, the switchback door indicator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” po- sition, the switchback door indicator light flashes for about 20 seconds and goes off when the switchback door is open.
3-14
(cid:132) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.6 US gal (10.0 liters, or 2.2 Imp gal). It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 3.7 US gal (14 liters, 3.1 Imp gal).
Promptly put fuel in the tank whenever the low fuel warning light comes on. If the engine mis- fired as a result of an empty tank, resulting cat- alyzer damage could cause damage to the tur- bocharger.
(cid:132) All-Wheel Drive warning light
(AT vehicles)
The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds.
(cid:84) Turbo models This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires. (cid:84) Non-turbo models This light comes on when All-Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes. This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires.
Continued driving with the AWD warning light flashing can lead to powertrain damage. If the AWD warning light flashes, promptly park in a safe place then check whether all four tires are the same diameter and whether any of the tires has a puncture or has lost air pressure for some other reason.
Instruments and controls
(cid:132) Security system status indicator
light (if equipped)
This light is found at the bottom center of the combina- tion meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, refer to the “Security system (if equipped)” in Chapter 2.
(cid:132) Selector lever position indicator (AT
vehicles)
This indicator shows the position of the selector lever.
UB3025AA
– CONTINUED – 3-15
Instruments and controls
(cid:132) Gear position indicator (Turbo-AT ve-
hicles)
UBS094AA
When the selector lever is in the manual gate, this in- dicator shows the currently selected gear.
(cid:132) Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
3-16
(cid:132) High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.
(cid:132) Cargo lamp indicator light
Do not switch on the cargo lamp while driving to avoid distracting other drivers.
This indicator light shows that the cargo lamp comes on.
(cid:132) Cruise control set indicator light (cid:84) Non-turbo models The light comes on when vehicle speed has been set. (cid:84) Turbo models The cruise set indicator light comes on when the igni- tion switch is turned to the “ON” position and goes out after about three seconds. The light comes on when vehicle speed has been set.
Instruments and controls
Clock
NOTE (cid:121) If you move the cruise control lever while turn- ing the ignition switch “ON”, the cruise control function is deactivated and the cruise control set indicator light flashes. To reactivate the cruise control function, turn the ignition switch back to the “ACC” or “LOCK” position, and then turn it again to the “ON” position. (cid:121) If this indicator light and the “ ” indicator light flash simultaneously during driving, have the vehicle checked by your nearest SUBARU dealer.
To set the time, turn the setting knob clockwise to ad- vance and counterclockwise to retard the time.
UB2013BA
To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.
– CONTINUED – 3-17
Instruments and controls
Light control switch
(cid:132) Headlights
To prevent battery discharge resulting from ac- cidentally leaving your lights on when your ve- hicle is parked, the light switch operates only when the ignition switch is in the “ON” posi- tion. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.
The light switch operates only when the ignition switch is in the “ON” position.
3-18
HS3026BA
To turn on the headlights, turn the knob on the end of the turn signal lever.
first position
Parking lights, instrument panel illumination, tail lights and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina- tion, tail lights, and license plate light are on.
(cid:132) High/low beam change (dimmer)
(cid:132) Headlight flasher
Instruments and controls
HS3026CA
HS3026DA
To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the in- strument panel is also on. To switch back to low beam, pull the lever back to the detent position.
Do not hold the lever in the flashing position for more than just a few seconds.
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” posi- tion. When the headlights are on high beam, the high beam – CONTINUED – 3-19
Instruments and controls
indicator light “ comes on.
” on the instrument panel also
Turn signal lever
(cid:132) Daytime running light system
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
The low beam headlights will automatically come on at reduced brightness when the engine has started, un- der the following conditions: (cid:121) The parking brake is fully released. (cid:121) The light switch is in the “OFF” or “
” position.
3-20
HS3027BC
1) Right turn 2) Left turn To activate the right turn signal, push the turn signal le- ver up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return af- ter cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction
of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.
Illumination brightness control
Instruments and controls
HS3028BB
1) Brighten 2) Darken When the lighting switch is in the “ ” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.
” or “
– CONTINUED – 3-21
Instruments and controls
Parking light switch
that will run down the battery.
HS3029BA
The parking light switch operates regardless of the ig- nition switch position. By pushing the front end of this switch, following lights will come on. – Parking lights – Front and rear side marker lights – Tail lights – License plate lights To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because
3-22
Fog light button
Wiper and washer
Instruments and controls
UB3030BA
The fog lights operate only when the headlights are on low beam. Push the fog light button to turn the fog lights on. Press the button again to turn them off. The indicator light located on the button will illuminate when the fog lights are on.
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
(cid:121) Do not operate the washer continuously for more than ten seconds, or when the washer flu- id tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. (cid:121) Do not operate the wipers when the wind- shield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. (cid:121) In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. At- – CONTINUED – 3-23
Instruments and controls
tempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to oper- ate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. (cid:121) If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper operation. (cid:121) Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer flu- id” section in chapter 11.) Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades. (cid:121) Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper
3-24
blades.
NOTE (cid:121) The wiper operates only when the ignition switch is in the “ON” or “ACC” position. (cid:121) Clean your wiper blades and window glass peri- odically with a washer solution to prevent streak- ing, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. (cid:121) Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wip- er operation and streaking on the glass. If you can- not remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with wa- ter. (cid:121) If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wind-
shield wiper blades” section (chapter 11) for re- placement instructions.
(cid:132) Windshield wiper and washer switches (cid:84) Windshield wipers
sition. (cid:84) Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. (cid:84) Wiper intermittent time control (if equipped)
Instruments and controls
P U L L L P U L L L M I S T
OFF
INT
LO
PULLL MIST
HI
UB3022BB
1) MIST To turn the wipers on, push the wiper control lever down.
: Intermittent LO: Low speed HI: High speed To turn the wipers off, return the lever to the “OFF” po-
UB3024BA
When the wiper switch is in the “ the dial to adjust the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your desired interval.
” position, turn
– CONTINUED – 3-25
Instruments and controls
(cid:84) Washer
P U L L L P U L L L M I S T
UB3023BA
To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers oper- ate while you push the button.
3-26
Rear window defogger button
(cid:121) Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. (cid:121) To prevent the battery from being dis- charged, do not operate the defogger continu- ously for any longer than necessary.
The rear window defogger operates only when the ig- nition switch is in the “ON” position. The rear window defogger button is located on the cli- mate control panel. The defogger will automatically shut off after about 15
minutes. If the window clears before that time, push the button to turn it off. It also turns off when the igni- tion switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again.UB3028BA
To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.
Instruments and controls
Windshield wiper deicer (if equipped)
To prevent the battery from being discharged, do not operate the windshield wiper deicer con- tinuously for any longer than necessary.
UB3029BA
The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the wind- – CONTINUED – 3-27
Instruments and controls
shield wiper deicer, push the button. The indicator light located on the button lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 minutes. If the wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the button to turn the deicer on again.
Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving.
(cid:132) Inside mirror
HS3036BB
1) Tab The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.
3-28
(cid:84) Auto-dimming mirror/compass (if equipped)
HS3037BB
1) Left button 2) Auto dimming indicator 3) Photosensor 4) Right button The auto-dimming mirror/compass has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also con- tains a built-in compass. (cid:121) By pressing and releasing the left button, the auto- matic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming in- dicator light (green) located to the right of the button
Instruments and controls
will illuminate. (cid:121) By pressing and releasing the right button, the com- pass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror sur- face turns bright if the transmission is shifted into re- verse. This is to ensure good rearward visibility during reversing. (cid:86) Photosensors
HS3038BA
The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors – CONTINUED – 3-29
Instruments and controls
detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. (cid:86) Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/ air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metal- lic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then re- lease, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should out- side influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.
3-30
(cid:86) Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map at the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is dis- played. 4. Releasing the button for 3 seconds will exit the zone setting mode.
(cid:132) Outside mirrors (cid:84) Convex mirror (Passenger side)
Objects look smaller in a convex mirror and far- ther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of ob-
jects that you view in convex mirror.
(cid:84) Adjusting mirrors
Instruments and controls
OM-U2737
To adjust the mirrors by hand, push where indicated by the arrows. (cid:84) Remote control mirror switch The remote control mirrors operate only when the ig- nition switch is in the “ON” or “ACC” position.
UB4004BB
1) Selection switch 2) Direction control switch 1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation. The mirrors can also be adjusted manually.
– CONTINUED – 3-31
The indicator light located on the button will come on when the outside mirror defogger heater in operation. To turn it off, push the button again.
Instruments and controls
(cid:84) Outside mirror defogger (if equipped)
To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position.
UB4004CB
1) Indicator light To turn on the outside mirror defogger, push the but- ton while the engine is running.
3-32
Tilt steering wheel
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.
Instruments and controls
place. 5. Make sure that the steering wheel is securely locked by moving it up and down.
HS3043BA
1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in
– CONTINUED – 3-33
Instruments and controls
Horn
To sound the horn, push the horn pad.
HS3044BA
3-34
Climate control
Manual heating and air conditioning
Ventilator ....................................................... 4-2
Driver’s side ventilators ................................... 4-2
Center ventilators ............................................. 4-2
Front passenger’s side ventilators ................. 4-3
Air flow selection .............................................. 4-4
system ........................................................ 4-5
Control panel ..................................................... 4-5
Heater operation ............................................... 4-7
Air conditioner operation ................................. 4-10
Operating tips for heater and air conditioner ................................................. 4-11
Air filtration system (if equipped) ................ 4-134-1
Climate control
Climate controlVentilator (cid:132) Driver’s side ventilators
(cid:132) Center ventilators
UB4038BB
Move the thumb-wheel up and down or right and left to adjust the flow direction.
UB4039BA
1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.
4-2
(cid:132) Front passenger’s side ventilators
UB4040BB
1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.
Climate control
– CONTINUED – 4-3
Climate control
(cid:132) Air flow selection
4-4
UB4036BA
Manual heating and air conditioning system (cid:132) Control panel
UB5004BC
1) Temperature control dial 2) Fan speed control dial 3) Air flow control dial 4) Air conditioner button 5) Air inlet selection button 6) Rear window defogger button (Refer to “Rear window
defogger button” in chapter 3.)
(cid:84) Temperature control dial This dial regulates the temperature of air flow from the
Climate control
air outlets over a range from the blue area (cool) to red area (warm). (cid:84) Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. (cid:84) Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets
and the foot outlets.
: Air flows through the foot outlets and some
through the windshield defroster outlets.
: Air flows through the windshield defroster outlets
and foot outlets.
: Air flows through the windshield defroster out-
lets.
– CONTINUED – 4-5
Climate control
” or “
NOTE When the dial is placed in the “ ” po- sition, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quick- ly. At the same time, the air inlet selection is auto- matically set to “Outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button. (cid:84) Air conditioner button
Push the air conditioner button while the fan is in op- eration to turn on the air conditioner. The indicator light will come on. Push it again to turn off the air conditioner. (cid:84) Air inlet selection button
Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
The air conditioner operates only when the engine is running.
UG4507BA
4-6
UB4041BA
ON position (Recirculation): Interior air is recirculat- ed inside the vehicle. Push the air inlet selection but- ton to the ON position. The indicator light will come on. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selec- tion button again to the OFF position. The indicator light will go off. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temper- ature and the road is no longer dusty.
Climate control
(cid:132) Heater operation (cid:84) Defrosting or defogging the windshield
UB5011AA
”.
To direct warm air to the windshield and front door win- dows: 1. Set the air flow control dial to “ 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the – CONTINUED – 4-7
Climate control
” position.
“ (cid:84) Heating and defrosting
(cid:84) Heating
UB5013AA
UB5012AA
”.
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to “ 2. Set the temperature control dial to the desired tem- perature level. 3. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
”.
To direct warm air toward the floor: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial to the desired tem- perature level. 4. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
4-8
(cid:84) Bi-level heating
Climate control
ference between the air from the instrument panel out- lets and the air from the foot outlets. (cid:84) Ventilation
UB5014AA
This setting allows you to direct air of different temper- atures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial to the desired tem- perature level. 4. Set the fan speed control dial to the desired speed. Setting the temperature control dial fully turned to the red area or blue area decreases the temperature dif-
”.
UB5015AA
To force outside air through the instrument panel out- lets: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed. When driving on a dusty road, set the air inlet control button to the “ON” position.
”.
– CONTINUED – 4-9
Climate control
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
(cid:132) Air conditioner operation (cid:84) Cooling or dehumidifying
compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue area. 5. Set the fan speed control dial at the desired speed. (cid:84) Defrosting or defogging
”.
UB5016BB
1) ON position For cooling and dehumidification of the passenger
UB5011BB
1) ON position To direct warm air to the windshield and front door win- dows: 1. Set the air outlet control dial to “
”.
4-10
2. Set the temperature control dial to the red area. 3. Set the fan speed control dial at the highest speed.
Climate control
Operating tips for heater and air con- ditioner (cid:84) Cleaning ventilator grille
UB4037BA
Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any ac- cumulation of insects and leaves on the condenser. (cid:84) Efficient cooling after parking in direct sunlight After parking in direct sunlight, drive with the windows
– CONTINUED – 4-11
(cid:84) Air conditioner compressor shut-off when en-
gine is heavily loaded
To improve acceleration and gas mileage, the air con- ditioner compressor is designed to temporarily shut off during air conditioner operation whenever the acceler- ator is fully depressed such as during rapid accelera- tion or when driving on a steep upgrade. (cid:84) Refrigerant for your climate control system Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Climate control
open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency. (cid:84) Lubrication oil circulation in the refrigerant cir-
cuit
Operate the air conditioner compressor at a low en- gine speed (at idle or low driving speeds) a few min- utes each month during the off-season to circulate its oil. (cid:84) Checking air conditioning system before sum-
mer season
Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer. (cid:84) Cooling and dehumidifying in high humidity
and low temperature weather condition
Under certain weather conditions (high relative humid- ity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
4-12
Air filtration system (if equipped) If your vehicle’s air conditioning system is equipped with a optional air filtration system, replace the filter el- ement according to the replacement schedule shown below. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more frequently. Have your filter checked or replaced by your SUBARU dealer.
Replacement schedule:
Every 12 months or 9,300 miles (15,000 km) whichev- er comes first
NOTE The filter can influence the air conditioning, heat- ing and defroster performance if not properly maintained.
Climate control
– CONTINUED – 4-13
Audio
Antenna system ............................................ Pillar mounted antenna (Non-turbo models) .. Roof mounted antenna (Turbo models) ......... FM reception ..................................................... Installation of accessories ........................... Audio set ........................................................ Type A audio set ............................................... Type B audio set ............................................... In-dash 6 CD auto changer (Optional audio unit – if equipped) ............... AM/FM radio with CD player ........................ Radio operation ................................................ Compact disc player operation ....................... CD changer control (if optional in dash CD changer is connected) ...................................
5-2
5-2
5-2
5-3
5-4
5-4
5-4
5-5
5-5
5-6
5-6
5-11
5-13
Type B audio set (if equipped) ..................... 5-17
5-17
5-23
In-dash 6 CD auto changer (if equipped) .... 5-27
Precautions to observe when handling a compact disc .......................................... 5-30Radio operation ................................................ Built-in CD changer operation .........................
5-1
Audio
AudioAntenna system (cid:132) Pillar mounted antenna (Non-turbo
models)
(cid:132) Roof mounted antenna (Turbo models)
Pull the antenna out to extend it to its full length.
UB5070BA
5-2
UB5073BA
UB5074BA
Stand the roof antenna up for use. You can detach the roof antenna by turning it counterclockwise. When fit- ting the roof antenna, turn it clockwise and tighten it securely.
When working on the cargo bed, be careful not to get poked in the eye by the roof antenna.
NOTE (cid:121) Detach the roof antenna before putting the vehi- cle in a garage and before washing it in an auto- matic car wash. (cid:121) After detaching the roof antenna, keep the mounting hole free of dirt and dust. If any dirt or dust sticks to the hole, remove it before attaching the roof antenna. (cid:121) When detaching the roof antenna, grasp and turn the roof antenna at the base. (cid:121) To avoid damaging the roof antenna, be careful not to overtighten it when attaching it. (cid:121) Radio reception is not possible with the roof an- tenna folded down. Also, reception deteriorates if metallic objects are placed near the roof antenna.
Audio
(cid:132) FM reception Although FM is normally static free, reception can be affected by the surrounding area, atmospheric condi- tions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary stat- ic, flutter or station interference. If reception continues to be unsatisfactory, switch to a stronger station.
– CONTINUED – 5-3
Audio
Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly in- stalled or if they are not suited for the vehicle.
Audio set Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in this sec- tion for operating details.
(cid:132) Type A audio set
UB5066AA
(cid:121) Radio operation: refer to page 5-6 (cid:121) CD (compact disc) player operation: refer to page 5- 11 (cid:121) CD changer control: refer to page 5-13
5-4
(cid:132) Type B audio set
(cid:132) In-dash 6 CD auto changer (Optional
audio unit – if equipped)
Audio
(cid:121) Radio operation: refer to page 5-17 (cid:121) Built-in CD changer operation: refer to page 5-23
UB5075AA
HS5011AA (cid:121) Inserting and removing a disc or all discs: refer to page 5-27
– CONTINUED – 5-5
(1) Power switch/Volume, Tone,
Balance, Fader control dial
(2) BAND button (3) Tuning buttons (4) Preset buttons (5) AUDIO button (6) SCAN button
Audio
AM/FM radio with CD player The audio set will operate only when the ignition switch is in the “ACC” or “ON” position.
(cid:132) Radio operation
(1)
(2)
(6)
(5)
(4)
(3)
UB5067BB
5-6
(cid:84) Power switch and volume/bass/treble/fader/
balance control
The “AUDIO” button (5) is used for selecting the fol- lowing control modes:
Audio
(cid:86) Power switch and volume control (PWR/VOL) The dial (1) is used for both power (ON/OFF) and vol- ume control. The radio is turned ON and OFF by push- ing the dial and the volume is controlled by turning the dial. (cid:86) Tone and balance control (AUDIO) The volume control dial (1) normally functions as a vol- ume control. This dial becomes a control for Bass, Treble, Fader or Balance when you select the appro- priate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds. To change control modes: Each brief press of the “AUDIO” button (5) changes control modes in the fol- lowing sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.)
Volume
Bass
Treble
Balance
Fader
– CONTINUED – 5-7
Audio
Display
Control mode
Bass control
Treble control
Balance control
Fader control
Turn counterclockwise
For less bass sound
For less treble sound
HS5014BA
Turn clockwise
For more bass sound
For more treble sound
To increase left speaker volume and
decrease right speaker volume
To increase right speaker volume and
decrease left speaker volume
To increase rear speaker volume and
decrease front speaker volume
To increase front speaker volume and
decrease rear speaker volume
Volume control
For less volume
For more volume
BAS TRE BAL
FAD
VOL
5-8
(cid:84) Waveband selection (cid:86) FM/AM selection Push the “BAND” button (2) to select FM1, FM2 or AM reception. The display indicates which one is currently selected. (cid:84) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. (cid:84) Tuning (TUNE) (cid:86) Manual tuning (TUNE) Press the “ crease the tuning frequency and press the “ of the button to decrease it. Each time the button is pressed, the frequency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode. (cid:86) Seek tuning (SEEK) If the tuning button (3) is pressed for longer than half of a second, the radio will begin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion.
” side of the tuning button (3) to in- ” side
Audio
(cid:86) Automatic tuning (SCAN) Press the “SCAN” button (6) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tun- ing, stations are scanned in the direction of low fre- quencies to high frequencies only. Automatic tuning may not function properly if the sta- tion reception is weakened by distance from the sta- tion or proximity to tall buildings and hills. (cid:84) Selecting preset stations Presetting a station with a “Preset” button (4) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. (cid:84) How to preset stations 1. Press the “BAND” button (2) to select FM1, FM2 or AM reception. 2. Press the “SCAN” button or tune the radio manually until the desired station frequency is displayed. 3. Press one of the “Preset” buttons for more than 2
– CONTINUED – 5-9Audio
seconds to store the frequency. At this time, there will momentarily be no sound from the radio. If the button is pressed for less than 2 seconds, the preceding se- lection will remain in memory. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is nec- essary to reset the preset buttons. (cid:121) If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
5-10
(cid:132) Compact disc player operation
(7)
(8)
(9)
(14) (15)
(13)
(12)
(11)
(10)
UB5067CB
Audio
(7) Disc slot (8) CD button (9) Eject button (10) Fast-forwarding and track up
(11) Fast-reversing and track down
button
button
(12) Random button (13) Repeat button (14) Scan button (15) PWR (power) switch
– CONTINUED – 5-11
Audio
(cid:84) To playback a compact disc (cid:86) When CD is not in the player Hold a disc with a finger in the center hole while grip- ping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatical- ly pull the disc into position. A 8 cm/3 inch CD may also be used without any adapt- er. NOTE (cid:121) DO NOT INSERT TWO DISCS INTO THE DISC IN- SERTION SLOT AT A TIME. (cid:121) Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. (cid:121) After the last song finishes, the player will auto- matically return to track 1 (the first song on the disc). (cid:86) When CD is in the player When the “CD” button (8) is pressed, the player will start playback. NOTE After the last song finishes, the player will auto- matically return to track 1 (the first song on the
5-12
disc). (cid:84) To stop playback of a CD When the “PWR” button (15) is pressed during play- back of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track num- ber will decrease. (cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “ for more than 0.5 second to fast-forward the disc. Release the button to stop fast-forwarding.
” side of the button (10) continuously
” side of the button (11) continuously
(cid:86) Fast-reversing Press the “ for more than 0.5 second to fast-reverse the disc. Release the button to stop fast-reversing. (cid:84) Repeat playback Use this to play a certain track repeatedly. During playback, press the “RPT” button (13) and release it in less than 2 seconds. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Use this to play the tracks on the disc in random order. During playback, press the “RAND” button (12) and hold it in for more than 2 seconds. The “RAND” indica- tor will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored. (cid:84) Scan Press the “SCAN” button (14) and release it in less than 2 seconds, and you can hear the first 10 seconds of each track to search for the desired program. To
Audio
continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored. (cid:84) To eject a disc from the player When a disc is being played back or when a disc is in the player, press the “Eject” button “ ” (9). The disc will be ejected. The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE (cid:121) Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. (cid:121) To protect the disc, the disc is automatically loaded if it is left in the ejected position for more than approximately 15 seconds (Auto Reload). In this case, the disc is not played.
(cid:132) CD changer control (if optional in dash
CD changer is connected)
An optional CD changer can be connected to this au- dio unit. See your SUBARU dealer for more informa- tion. For procedures for loading and unloading CDs, refer to “In-dash 6 CD auto changer (Optional audio unit – if equipped)” in this chapter.
– CONTINUED – 5-13
(16) CD button (17) Track selection buttons (18) RAND (Random) button (19) RPT (Repeat) button (20) SCAN button
(16)
(20)
(19)
(18)
(17)
UB5067DB
Audio
5-14
(cid:84) To start playback Press the “CD” button (16). The “CD” indicator will come on and the disc number will appear on the dis- play and the CD changer will start playback. NOTE (cid:121) If the “CD” button is pressed during a radio broadcast, the CD changer will interrupt the broadcast. (cid:121) At the end of the disc, playback automatically continues with the next disc. (cid:121) After playback on the last disc finishes, the play- er will automatically return to the first disc. (cid:121) If you have loaded fewer than 6 discs, any miss- ing disc is automatically skipped. (cid:84) Selection of a desired disc Discs cannot be selected using the main audio unit. To select a disc, press one of the “Disc select” buttons (these are numbered from 1 to 6) on the CD changer unit. The disc will begin to play. (cid:84) To select a song from its beginning Briefly press the “ ” side of the track selection but- ton (17) to skip to the beginning of the next track and briefly press the “ ” side of the button to skip to the beginning of the current track.
Audio
” side of the button continuously for
(cid:84) Fast-forwarding and fast-reversing Press the “ ” side of the track selection button (17) continuously for more than a half second to fast-for- ward the disc. Press the “ more than a half second to fast-reverse the disc. Release the button to stop fast-forwarding or fast-re- versing. (cid:84) Repeat playback Press the “RPT” button (19) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Press the “RAND” button (18) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored.
– CONTINUED – 5-15
Audio
a disc)
(cid:84) Scan (a convenient way to become familiar with
1. Press the “SCAN” button (20).
– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after play- ing all programs. Then, normal playback starts.
2. Press the “SCAN” button again when you hear a track you like.
– Normal playback resumes.
(cid:84) To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
5-16
Type B audio set (if equipped) The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
(cid:132) Radio operation
(1)
(2)
(3)
(4)
(5)
Audio
(1) Power switch, Volume control, Bass/Midrange/Treble control and Fader/Balance control dial
(2) AUDIO (audio mode) button (3) Fader/Balance selection button (4) FM button (5) AM button (6) Preset buttons (7) Tuning buttons (8) SCAN button
(8)
(7)
(6)
UB5072BB
– CONTINUED – 5-17
Audio
(cid:84) Power switch and volume/bass/treble/fader/
balance control (PWR/VOL)
The dial (1) is used for both power (ON/OFF) and vol- ume control. The radio is turned ON and OFF by push- ing the dial and the volume is controlled by turning the dial. This dial is used for bass/midrange/treble controls when the “AUDIO” button (2) is in the depressed posi- tion. It is also used for fader/balance controls when the “BAL” button (3) is in the depressed position.
5-18
Display
Control mode
Audio
BASS MIDDLE TREBLE FADER
Bass control
Midrange control
Treble control
Fader control
Turn counterclockwise
For less bass sound
HS5014BA
Turn clockwise
For more bass sound
For less midrange sound
For more midrange sound
For less treble sound
For more treble sound
To increase rear speaker volume and de-
crease front speaker volume
To increase front speaker volume and de-
crease rear speaker volume
BALANCE
Balance control
To increase left speaker volume and de-
crease right speaker volume
To increase right speaker volume and de-
crease left speaker volume
VOLUME
Volume control
For less volume
For more volume
– CONTINUED – 5-19
Audio
(cid:86) Tone control The volume control dial (1) normally function as vol- ume control. The dial become a control for Bass, Midrange or Treble when you select the appropriate tone control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds. To change control modes: Each brief press of the “AUDIO” button (2) changes control modes in the fol- lowing sequence starting from bass control mode. (When the radio is first turned on, the control mode is in the volume control.)
Bass
Midrange
Treble
Volume
(cid:86) Fader and balance control The volume control dial (1) normally function as vol- ume control. The dial become the controls for Fader or Balance when you select the appropriate fader and balance control mode. Choose desired setting for each mode by turning the volume control dial. The control function returns to vol- ume control mode after about 5 seconds. To change control modes: Each brief press of the
5-20
“BAL” button (3) changes control modes in the follow- ing sequence starting from fader control mode. (When the radio is turned on, the control mode is in the vol- ume control.)
Fader
Balance
Volume
(cid:86) Display illumination dimness cancellation
(BRIGHT)
” or “
The brightness of the radio display dims when the light switch is in the “ ” positions. If this makes the display difficult to read, press the volume dial for more than 1.5 seconds to return the display to original brightness. Subsequently pressing the volume dial again for more than 1.5 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” position makes the radio display dim again. (cid:84) FM/AM selection button (cid:86) FM button Press the “FM” button (4) for FM reception. The radio will toggle between FM1 and FM2 settings each time the “FM” button (4) is subsequently pressed.
” or “
” side of the tuning button (7) to in- ” side
(cid:86) AM button Press the “AM” button (5) for AM reception. (cid:84) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. (cid:84) Manual tuning (TUNE) (cid:86) Manual tuning for AM and FM Push the “ crease the tuning frequency and press the “ of the button to decrease it. Each time the button is pressed, the frequency chang- es 10 KHz in the AM waveband and 0.2 MHz in the FM waveband. (cid:86) Seek tuning (SEEK) If the tuning button (7) is pressed for longer than half of a second, the radio will begin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion. (cid:84) Automatic tuning (SCAN) Press the “SCAN” button (8) to change the radio to the
Audio
SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tun- ing, stations are scanned in the direction of low fre- quencies to high frequencies only. Automatic tuning may not function properly if the sta- tion reception is weakened by distance from the sta- tion or proximity to tall buildings and hills. (cid:84) Selecting preset stations Presetting a station with a “Preset” button (6) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. (cid:84) How to preset stations 1. Press the “FM/AM” selection button to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (8) or tune the radio man- ually until the desired station frequency is displayed. 3. Press one of the “Preset” buttons (6) for at least 1.5
seconds to store the frequency. The frequency of the station will flash once on the display at this time. If the – CONTINUED – 5-21Audio
button is pressed for less than 1.5 seconds, the pre- ceding selection will remain in memory. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is nec- essary to reset the preset buttons. (cid:121) If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
5-22
(cid:132) Built-in CD changer operation
(9)
(10)
(11)
(12)
(13)
(14)
Audio
(9) Eject button (10) Disc slot (11) CD (CD player selection) button (12) Repeat button (13) Random button (14) LOAD button (15) Disc select buttons (16) Track selection buttons (17) SCAN button
(17)
(16)
(15)
UB5072CB
– CONTINUED – 5-23
Audio
NOTE Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. (cid:84) How to insert a CD(s) (cid:86) Inserting a CD 1. Press “LOAD” button (14). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle position will blink. If no indicator blinks, it means that there is no idle po- sition in the magazine. 2. As soon as the “DISC” indicator begins to blink, the “IN” will appear on display for a period of 15 seconds. Insert a disc during the period. The disc will be then automatically drawn in, and the player will begin to play back the first track of the disc. (cid:121) To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” button, the player will begin to play back the first track of the last disc you have in- serted.5-24
(cid:121) The disc indicator steadily lights up if a disc is al- ready inserted in the corresponding position of the magazine. (cid:121) While the player is in the loading mode, if you press the “FM” button (4) or “AM” button (5), the player will enter the standby mode. Press the “CD” button (11) to start playback. (cid:86) Inserting a disc in a desired position 1. Press the “LOAD” button. If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle position will blink. The positions in the magazine the indicator of which steadily lights up are already loaded with discs. 2. Press the “Disc select” button (15) at the position where you want to insert a disc. The associated “DISC” indicator will blink, and the “IN” will be dis- played. 3. If you insert a disc during the 15-second period while the “IN” is on display, the disc will be automati- cally drawn in, and the player will start playback of the disc, beginning with the first track. (cid:121) To insert more discs in succession, repeat Steps 1
and 2. (cid:121) While the player is in the loading mode, if you press the “FM” button (4) or “AM” button (5), the player willenter standby mode. Press the “CD” button to start playback. (cid:86) Loading all the magazine (Full disc loading
mode)
1. If you continue to press the “LOAD” button for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2. A “DISC” indicator will blink, and the “IN” will be on display for a period of 15 seconds. If a disc is success- fully loaded during this period, the “DISC” indicator will stop blinking and will steadily light. 3. When the loading of a disc is complete, the next “DISC” indicator will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15 seconds in- terval, the full disc loading mode will be canceled, and the player will start playback of the disc inserted first. (cid:84) How to play back a CD or make a pause (cid:86) When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first track.
Audio
(cid:86) When there are CDs loaded: Press a desired one of the “Disc select” buttons (15) the “DISC” indicator of which steadily lights up. The player will then start playback of the selected CD, be- ginning with the first track. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” side of the button (16) to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” side of the button (16) to skip to the beginning of the current track. Each time the but- ton is pressed, the indicated track number will de- crease. (cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “ more than 0.5 second to fast-forward the disc. Release the button to stop fast-forwarding. (cid:86) Fast-reversing Press the “ more than 0.5 second to fast-reverse the disc.
” side of the button (16) continuously for
” side of the button (16) continuously for
– CONTINUED – 5-25
Audio
Release the button to stop fast-reversing. (cid:84) Repeat playback Press the “RPT” button (12) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Press the “RAND” button (13) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored. (cid:84) Scan When the “SCAN” button (17) is pressed while the disc is being played back, you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal playback mode is restored.
5-26
(cid:84) How to unload CDs from the player (cid:86) Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the “Disc select” button (15) of the disc whose “DISC” indicator is ON. 2. Press the “Eject” button (9). Then the “DISC” indi- cator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1
and 2. (cid:86) Ejecting all discs from the player (All disc ejec-tion mode)
1. If you continue to press the “Eject” button (9), the player will produce beep sound and will enter the all disc ejection mode. 2. Remove the disc that has been ejected. The other discs loaded will then be ejected one after another. If you do not remove the disc that has been ejected, the “All disc ejection mode” will be canceled. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
In-dash 6 CD auto changer (if equipped)
(1)
(2)
Audio
(1) Disc slot (2) Disc indicators (disc No.1 to 6) (3) Disc select buttons (disc No.1 to
6)
(4) Eject button
(4)
(3)
HS5016BB
– CONTINUED – 5-27
Audio
mark.
identified by
(cid:121) Do not attempt to insert two or more discs into the slot at a time. Doing so can cause me- chanical damage to the CD changer. (cid:121) Use only music CDs (cid:121) Do not use CDs listed below which could cause damage to the CD player.
