Login- Download PDF Manual
-
3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the in- side door lock levers. 5. Close the doors. The system will automatically arm after one minute. In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arming will take place immediately regardless of whether or not the passive mode has been selected. (cid:84) Disarming the system To disarm the system, briefly press the “UNLOCK/ – CONTINUED – 2-19
switch to “ON”.
Keys and doors
DISARM” button on the transmitter. (cid:84) Tripped sensor identification If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the sys- tem, this indicates that the alarm was triggered. The number of times the indicator light flashes indicates what sensor caused the alarm condition. To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to “ON” twice. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing. The indicator light provides the following indications. Flashing once: Any door has been opened. Flashing three times: The impact sensor in the sys- tem’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected. NOTE The battery must be reconnected before the indi- cator light will flash. To exit this mode, close the door and turn the ignition
2-20
Child safety locks
Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.
Keys and doors
the doors from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.
1) Lock 2) Unlock Each rear door has a child safety lock that prevents
UB2002BB
– CONTINUED – 2-21
Keys and doors
Windows (cid:132) Power windows
To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window. (cid:121) Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.
The power windows operate only when the ignition switch is in the “ON” position.
2-22
(cid:84) Driver’s side switches
UB2008BB
1) Lock switch 2) For driver’s window 3) For rear left passenger’s window 4) For front passenger’s window 5) For rear right passenger’s window All door windows can be controlled by the power win- dow switch cluster at the driver side door.
(cid:86) Operating the driver’s window
UB2008DB
1) Lock 2) Unlock 3) Close 4) Open 5) Automatically open To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without hold- ing the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window half-
Keys and doors
way, pull the switch up lightly. To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows To open the passengers’ windows, push the appropri- ate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired posi- tion. (cid:86) Locking the passengers’ windows To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.
– CONTINUED – 2-23
Keys and doors
(cid:84) Passengers’ side switches
Front passenger’s window switch 1) Open 2) Close
2-24
UB2009CB
UB2005BB
Rear passenger’s window switches 1) Open 2) Close To open the window, push the switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.
Tailgate
Keep the tailgate closed when the vehicle is moving. If you must drive with the tailgate open, use the optional SUBARU Bed Extender and place the License Plate Bracket at its fully lowered/open position. Cargo must not stick out beyond the Extender. Otherwise a danger- ous road hazard or personal injury could result.
Keys and doors
upper surface of the rear bumper to avoid damaging the tailgate. To open the tailgate, lift up on its handle while pulling the tailgate toward you. The support cables hold the tailgate open. See “Loading your vehicle” section in Chapter 8 for precautions in loading cargo. To close the tailgate, firmly push it upward until it latch- es. After you put the tailgate back up, pull it back toward you to be sure it latches securely.
Before opening the tailgate, remove any object on the
UB2050BA
– CONTINUED – 2-25
Keys and doors
(cid:132) License plate bracket
UB2051BA
When you drive with the tailgate open and with the bed extender used, the license plate bracket must be placed at its fully lowered/open position to make the rear license plate visible.
In order to avoid damaging the license plate bracket or the bumper, the license plate bracket must be in its fully lowered/open position be- fore the tailgate is lowered.
2-26
UBB096BA
To use the license plate bracket at its lowered/open
UB2053BA
position, push the two release buttons and pull the li- cense plate bracket up until it clicks. And then open the tailgate. If your vehicle is equipped with a trailer hitch, remove the ball mount from the hitch receiver tube before opening the tailgate. Failure to follow this procedure could result in damage to the license plate bracket. When you drive with the tailgate closed, the license plate bracket must be restored to its original position. To restore the license plate bracket to its original posi- tion, close the tailgate, and then pull the license plate bracket down until it clicks. If the license plate bracket is hard to be restored to its original position, mud may have accumulated on the back of the license plate bracket. Remove accumulat- ed mud before pulling the license bracket down.
Keys and doors
Switchback door
With the switchback door open, you can increase the usable cargo space and can carry long objects.
UB2052BA
In order to avoid damaging the license plate bracket or the bumper, the license plate bracket must be restored to its original position until it clicks.
Secure long objects properly to prevent them from sliding forward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equivalent.
– CONTINUED – 2-27
Keys and doors
Pay attention that your fingers do not get pinched with the switchback door when open- ing and closing it.
To open the switchback door:
1. Pull up the rear seat cushion. Refer to “Rear seats” section in Chapter 1 for operating details.
UB1172BA
2-28
UB1112CB
1) Red A) LOCK B) UNLOCK
Keys and doors
UB1113BA
UB1114BA
2. Unlock the rear seatback by pulling up on the knob and fold down the rear seatback. Confirm that the pins located at the bottom of the seat cushion is inserted into the slots at the top of the seatback.
3. Fold down the switchback door by releasing the – CONTINUED – 2-29
UB1115BA
the vehicle body that prevent the door from ful- ly closing or that crimp the weather strip around the door.
To close the switchback door, firmly push it upward until it latches. Return the seatback and seat cushion to their original positions and make sure they are securely locked.
After returning the seatback to its original posi- tion, make sure that the rear seatback has been securely locked. When securely locked, the red marks on the locking knobs are no longer visi- ble.
Keys and doors
lock knob. Then you can have a flat and larger cargo space. 4. Place the long object on the cargo bed through the switchback door opening. Be sure all items are secured in place. NOTE (cid:121) When opening the switchback door in snow, ac- cumulated snow in the cargo bed may enter the passenger compartment which could result in dampness in the passenger compartment. Prior to opening of the switchback door, brush off the snow completely. (cid:121) Close the switchback door whenever you leave the vehicle to prevent unauthorized entry.
The switchback door should be kept complete- ly shut when the vehicle is idling in an enclosed or partially enclosed area to avoid the possibil- ity of exhaust gas entering the passenger com- partment. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is extremely dangerous, or even lethal if in- haled. To ensure that exhaust gas cannot pen- etrate the switchback door, make certain that there are no obstructions between the door and
2-30
(cid:132) Switchback door indicator light
Moonroof (if equipped)
Keys and doors
UB7023EA
While the ignition switch is in the “ON” position, the switchback door indicator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” po- sition, the switchback door indicator light flashes for about 20 seconds and goes off when the switchback door is open.
Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident. To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) Before closing the moonroof, make sure that no one’s hands, arms, neck, head or other ob- jects will be accidentally caught in the moon- roof. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.
(cid:121) Do not sit on the edge of the open moonroof.
– CONTINUED – 2-31
Keys and doors
(cid:121) Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
(cid:132) Tilting/sliding moonroof The moonroof has both tilting and sliding functions. The moonroof operates only when the ignition switch is in the “ON” position.
UB2034BB
1) Open/Close switch 2) Tilt switch (cid:84) To raise or lower the moonroof The tilting function will only operate when the moon-
2-32
roof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause damage to the moon- roof. (cid:84) To open or close the moonroof Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you con- tinue to press on the switch. Release the switch once and push it again to close the moonroof completely. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to pre- vent water drops from falling into the passenger com- partment. NOTE If the moonroof cannot be closed through the switch operation because of system failure, it can
be closed manually using a hex-headed wrench. For the procedure, refer to “Moonroof – if the moonroof cannot be closed” in Chapter 9 “In case of emergency”.
(cid:132) Sun shade
UG2510BA
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
Keys and doors
– CONTINUED – 2-33
Ignition switch .............................................. LOCK .................................................................. ACC .................................................................... ON ....................................................................... START ................................................................ Key reminder chime .......................................... Ignition switch light (if equipped) .................... Key interlock release (AT vehicles) ................. Hazard warning flasher ................................ Meters and gauges ....................................... Speedometer ..................................................... Odometer/Trip meter ........................................ Tachometer ........................................................ Outside temperature indicator (if equipped) .. Fuel gauge ......................................................... Temperature gauge ........................................... Warning and indicator lights ....................... Seatbelt warning light and chime .................... SRS airbag system warning light .................... CHECK ENGINE warning light/Malfunction indicator lamp ................................................. Charge warning light ........................................ Oil pressure warning light ................................ AT OIL TEMPerature warning light (AT vehicles) ................................................... ABS warning light ............................................. Brake system warning light ............................. Door ajar warning lights ................................... Switchback door indicator light ...................... Low fuel warning light ...................................... All-Wheel Drive warning light (AT vehicles) ...
3-2
3-2
3-3
3-3
3-4
3-4
3-4
3-4
3-5
3-6
3-6
3-6
3-7
3-7
3-8
3-8
3-9
3-9
3-10
3-10
3-11
3-12
3-12
3-12
3-13
3-14
3-14
3-14
3-14Instruments and controls
Headlights ......................................................... High/low beam change (dimmer) .................... Headlight flasher ............................................... Daytime running light system .........................
Security system status indicator light (if equipped) .................................................... Selector lever position indicator (AT vehicles) ................................................... Gear position indicator (Turbo-AT vehicles) .. Turn signal indicator lights .............................. High beam indicator light ................................. Cargo lamp indicator light ............................... Cruise control set indicator light ....................
3-15
3-15
3-16
3-16
3-16
3-16
3-16
Clock .............................................................. 3-17
Light control switch ...................................... 3-18
3-18
3-19
3-19
3-20
Turn signal lever ........................................... 3-20
Illumination brightness control ................... 3-21
Parking light switch ...................................... 3-22
Fog light button ............................................. 3-23
Wiper and washer ......................................... 3-23
3-25
Rear window defogger button ..................... 3-26
Windshield wiper deicer (if equipped) ........ 3-27
Mirrors ............................................................ 3-28
3-28
3-30
Tilt steering wheel ......................................... 3-33
Horn ................................................................ 3-34Inside mirror ...................................................... Outside mirrors .................................................
Windshield wiper and washer switches .........
3-1
Instruments and controls
Instruments and controls
Ignition switch
Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
The ignition switch has four positions: LOCK, ACC, ON and START.
UB4000CA
3-2
NOTE (cid:121) Keep the ignition switch in the “LOCK” position when the engine is not running. (cid:121) Using electrical accessories for a long time with the ignition switch in the “ON” or “ACC” position can cause the battery to go dead. If the ignition switch will not move from the “LOCK” position to the “ACC” position, turn the steering wheel slightly to the left and right as you turn the ignition switch. (cid:121) If the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch. Also, if a large key- holder is attached to the key, your knees or hands may accidentally touch it in a way that turns the ig- nition switch.
(cid:132) LOCK The key can only be inserted or removed in this posi- tion. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.
(cid:84) Automatic transmission vehicles
Instruments and controls
The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. (cid:84) Manual transmission vehicles
HS3015BA
HS2020CA
HS2020DA
The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.
(cid:132) ACC In this position the electrical accessories (radio, ciga- rette lighter socket, etc.) can be used.
(cid:132) ON This is the normal operating position after the engine – CONTINUED – 3-3
Instruments and controls
is started.
(cid:132) START
Do not turn the ignition switch to the “START” position while the engine is running.
The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
(cid:132) Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ig- nition switch.
(cid:132) Ignition switch light (if equipped) For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened. The light remains on for 10 seconds and goes out after driver’s door is closed or if the key is turned
3-4
to the “ON” position.
(cid:132) Key interlock release (AT vehicles) If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using a Phillips screwdriver.
HS3016BA
UG3025BA
3. Turn the ignition key while pressing the key inter- lock release lever. Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired.
Instruments and controls
Hazard warning flasher
UB8002BA
The hazard warning flasher is used to warn other driv- ers when you have to park your vehicle under emer- gency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the haz- ard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
– CONTINUED – 3-5
Instruments and controls
Meters and gauges (cid:132) Speedometer The speedometer shows the vehicle speed.
(cid:132) Odometer/Trip meter
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
UB3026BB
1) Trip meter 2) Odometer (cid:84) Odometer The odometer shows the total distance that the vehicle has been driven.
3-6
(cid:84) Double trip meter
UB3027BB
1) A trip meter 2) B trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.
A trip meter To set the trip meter to zero, select either the A trip or B trip meter and push the knob and keep it pushed for
B trip meter
Instruments and controls
more than 1 second. NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.
(cid:132) Tachometer
Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.
The tachometer shows the engine speed in thousands of revolutions per minute.
(cid:132) Outside temperature indicator (if
equipped)
The outside temperature indicator shows the outside – CONTINUED – 3-7
Instruments and controls
temperature in a range from –22 to 122°F (–30 to 50°C). The indicator can give a false reading under any of the following conditions: (cid:121) When there is too much sun. (cid:121) During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately follow- ing a shutdown. (cid:121) When the actual outside temperature falls outside the specified indicator range.
(cid:132) Fuel gauge The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ig- nition switch is in the “ACC” or “LOCK” position. The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.
(cid:132) Temperature gauge
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possi-
3-8
ble. See “In case of emergency” in chapter 9.
UB2012BB
1) Normal operating range The temperature gauge shows engine coolant temper- ature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with
the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
Instruments and controls
Warning and indicator lights Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:
Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light / Malfunction indica- tor lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light All-Wheel Drive warning light (AT vehicles)
If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair.
(cid:132) Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the remind-
– CONTINUED – 3-9
Instruments and controls
er chime will sound for about six seconds to remind the driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off auto- matically after six seconds.
(cid:132) SRS airbag system warning
light
If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly re- paired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of inju- ry. (cid:121) Flashing or flickering of the indicator light. (cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” posi- tion.
3-10
(cid:121) Continuous illumination of the warning light. (cid:121) Illumination of the warning light while driv- ing.
When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS frontal airbag and seatbelt pretensioners are in normal operation.
(cid:132) CHECK ENGINE warning light/
Malfunction indicator lamp
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
If this light comes on steadily or blinks while the engine
is running, it may indicate that there is a problem or po- tential problem somewhere in the emission control system. (cid:84) If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control sys- tem malfunction has been detected. You should have your vehicle checked by an autho- rized SUBARU dealer immediately. NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indica- tor lamp coming on could be a loose or missing fuel fill- er cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK EN- GINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer im- mediately. (cid:84) If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the
Instruments and controls
emission control system. To prevent serious damage to the emission control system, you should do the following: (cid:121) Reduce vehicle speed. (cid:121) Avoid hard acceleration. (cid:121) Avoid steep uphill grades. (cid:121) Reduce the amount of cargo, if possible. (cid:121) Stop towing a trailer as soon as possible. The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.
(cid:132) Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU deal- er immediately.
– CONTINUED – 3-11
Instruments and controls
(cid:132) Oil pressure warning light
Do not operate the engine with the oil pressure warning light on. This may cause serious en- gine damage.
If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil lev- el is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
(cid:132) AT OIL TEMPerature warning
light (AT vehicles)
The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid tem- perature is too hot.
3-12
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. (cid:84) Automatic transmission control system warn-
ing
If the light flashes after the engine starts, it may indi- cate that the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.
(U.S.) (cid:132) ABS warning light (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. (cid:121) The warning light does not come on when the ignition switch is turned to the “ON” position.
(cid:121) The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). (cid:121) The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
NOTE If the warning light behavior is as described be- low, the ABS system may be considered normal. (cid:121) The warning light comes on right after the en- gine is started but goes out immediately, remain- ing off. (cid:121) The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12 km/h). (cid:121) The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery volt- age and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.
Instruments and controls
(cid:132) Brake system warning light
(U.S.) (Canada)
(cid:121) Driving with the brake system warning light on is dangerous. This indicates your brake sys- tem may not be working properly. If the light re- mains on, have the brakes inspected by a SUBARU dealer immediately. (cid:121) If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.
This light has the following two functions: (cid:84) Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. (cid:84) Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid res- ervoir with the ignition switch in the “ON” position and with the parking brake fully released.
– CONTINUED – 3-13
Instruments and controls
If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the near- est safe place and check the brake fluid level. If the flu- id level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the near- est SUBARU dealer for repair.
(cid:132) Door ajar warning lights The specific door ajar warning light comes on if any door is not fully closed. Always make sure this light is out before you start to drive.
(cid:132) Switchback door indicator light While the ignition switch is in the “ON” position, the switchback door indicator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” po- sition, the switchback door indicator light flashes for about 20 seconds and goes off when the switchback door is open.
3-14
(cid:132) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.6 US gal (10.0 liters, or 2.2 Imp gal). It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 3.7 US gal (14 liters, 3.1 Imp gal).
Promptly put fuel in the tank whenever the low fuel warning light comes on. If the engine mis- fired as a result of an empty tank, resulting cat- alyzer damage could cause damage to the tur- bocharger.
(cid:132) All-Wheel Drive warning light
(AT vehicles)
The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds.
(cid:84) Turbo models This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires. (cid:84) Non-turbo models This light comes on when All-Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes. This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires.
Continued driving with the AWD warning light flashing can lead to powertrain damage. If the AWD warning light flashes, promptly park in a safe place then check whether all four tires are the same diameter and whether any of the tires has a puncture or has lost air pressure for some other reason.
Instruments and controls
(cid:132) Security system status indicator
light (if equipped)
This light is found at the bottom center of the combina- tion meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, refer to the “Security system (if equipped)” in Chapter 2.
(cid:132) Selector lever position indicator (AT
vehicles)
This indicator shows the position of the selector lever.
UB3025AA
– CONTINUED – 3-15
Instruments and controls
(cid:132) Gear position indicator (Turbo-AT ve-
hicles)
UBS094AA
When the selector lever is in the manual gate, this in- dicator shows the currently selected gear.
(cid:132) Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
3-16
(cid:132) High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.
(cid:132) Cargo lamp indicator light
Do not switch on the cargo lamp while driving to avoid distracting other drivers.
This indicator light shows that the cargo lamp comes on.
(cid:132) Cruise control set indicator light (cid:84) Non-turbo models The light comes on when vehicle speed has been set. (cid:84) Turbo models The cruise set indicator light comes on when the igni- tion switch is turned to the “ON” position and goes out after about three seconds. The light comes on when vehicle speed has been set.
Instruments and controls
Clock
NOTE (cid:121) If you move the cruise control lever while turn- ing the ignition switch “ON”, the cruise control function is deactivated and the cruise control set indicator light flashes. To reactivate the cruise control function, turn the ignition switch back to the “ACC” or “LOCK” position, and then turn it again to the “ON” position. (cid:121) If this indicator light and the “ ” indicator light flash simultaneously during driving, have the vehicle checked by your nearest SUBARU dealer.
To set the time, turn the setting knob clockwise to ad- vance and counterclockwise to retard the time.
UB2013BA
To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.
– CONTINUED – 3-17
Instruments and controls
Light control switch
(cid:132) Headlights
To prevent battery discharge resulting from ac- cidentally leaving your lights on when your ve- hicle is parked, the light switch operates only when the ignition switch is in the “ON” posi- tion. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.
The light switch operates only when the ignition switch is in the “ON” position.
3-18
HS3026BA
To turn on the headlights, turn the knob on the end of the turn signal lever.
first position
Parking lights, instrument panel illumination, tail lights and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina- tion, tail lights, and license plate light are on.
(cid:132) High/low beam change (dimmer)
(cid:132) Headlight flasher
Instruments and controls
HS3026CA
HS3026DA
To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the in- strument panel is also on. To switch back to low beam, pull the lever back to the detent position.
Do not hold the lever in the flashing position for more than just a few seconds.
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” posi- tion. When the headlights are on high beam, the high beam – CONTINUED – 3-19
Instruments and controls
indicator light “ comes on.
” on the instrument panel also
Turn signal lever
(cid:132) Daytime running light system
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
The low beam headlights will automatically come on at reduced brightness when the engine has started, un- der the following conditions: (cid:121) The parking brake is fully released. (cid:121) The light switch is in the “OFF” or “
” position.
3-20
HS3027BC
1) Right turn 2) Left turn To activate the right turn signal, push the turn signal le- ver up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return af- ter cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction
of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.
Illumination brightness control
Instruments and controls
HS3028BB
1) Brighten 2) Darken When the lighting switch is in the “ ” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.
” or “
– CONTINUED – 3-21
Instruments and controls
Parking light switch
that will run down the battery.
HS3029BA
The parking light switch operates regardless of the ig- nition switch position. By pushing the front end of this switch, following lights will come on. – Parking lights – Front and rear side marker lights – Tail lights – License plate lights To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because
3-22
Fog light button
Wiper and washer
Instruments and controls
UB3030BA
The fog lights operate only when the headlights are on low beam. Push the fog light button to turn the fog lights on. Press the button again to turn them off. The indicator light located on the button will illuminate when the fog lights are on.
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
(cid:121) Do not operate the washer continuously for more than ten seconds, or when the washer flu- id tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. (cid:121) Do not operate the wipers when the wind- shield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. (cid:121) In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. At- – CONTINUED – 3-23
Instruments and controls
tempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to oper- ate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. (cid:121) If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper operation. (cid:121) Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer flu- id” section in chapter 11.) Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades. (cid:121) Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper
3-24
blades.
NOTE (cid:121) The wiper operates only when the ignition switch is in the “ON” or “ACC” position. (cid:121) Clean your wiper blades and window glass peri- odically with a washer solution to prevent streak- ing, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. (cid:121) Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wip- er operation and streaking on the glass. If you can- not remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with wa- ter. (cid:121) If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wind-
shield wiper blades” section (chapter 11) for re- placement instructions.
(cid:132) Windshield wiper and washer switches (cid:84) Windshield wipers
sition. (cid:84) Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. (cid:84) Wiper intermittent time control (if equipped)
Instruments and controls
P U L L L P U L L L M I S T
OFF
INT
LO
PULLL MIST
HI
UB3022BB
1) MIST To turn the wipers on, push the wiper control lever down.
: Intermittent LO: Low speed HI: High speed To turn the wipers off, return the lever to the “OFF” po-
UB3024BA
When the wiper switch is in the “ the dial to adjust the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your desired interval.
” position, turn
– CONTINUED – 3-25
Instruments and controls
(cid:84) Washer
P U L L L P U L L L M I S T
UB3023BA
To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers oper- ate while you push the button.
3-26
Rear window defogger button
(cid:121) Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. (cid:121) To prevent the battery from being dis- charged, do not operate the defogger continu- ously for any longer than necessary.
The rear window defogger operates only when the ig- nition switch is in the “ON” position. The rear window defogger button is located on the cli- mate control panel. The defogger will automatically shut off after about 15
minutes. If the window clears before that time, push the button to turn it off. It also turns off when the igni- tion switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again.UB3028BA
To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.
Instruments and controls
Windshield wiper deicer (if equipped)
To prevent the battery from being discharged, do not operate the windshield wiper deicer con- tinuously for any longer than necessary.
UB3029BA
The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the wind- – CONTINUED – 3-27
Instruments and controls
shield wiper deicer, push the button. The indicator light located on the button lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 minutes. If the wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the button to turn the deicer on again.
Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving.
(cid:132) Inside mirror
HS3036BB
1) Tab The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.
3-28
(cid:84) Auto-dimming mirror/compass (if equipped)
HS3037BB
1) Left button 2) Auto dimming indicator 3) Photosensor 4) Right button The auto-dimming mirror/compass has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also con- tains a built-in compass. (cid:121) By pressing and releasing the left button, the auto- matic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming in- dicator light (green) located to the right of the button
Instruments and controls
will illuminate. (cid:121) By pressing and releasing the right button, the com- pass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror sur- face turns bright if the transmission is shifted into re- verse. This is to ensure good rearward visibility during reversing. (cid:86) Photosensors
HS3038BA
The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors – CONTINUED – 3-29
Instruments and controls
detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. (cid:86) Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/ air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metal- lic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then re- lease, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should out- side influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.
3-30
(cid:86) Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map at the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is dis- played. 4. Releasing the button for 3 seconds will exit the zone setting mode.
(cid:132) Outside mirrors (cid:84) Convex mirror (Passenger side)
Objects look smaller in a convex mirror and far- ther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of ob-
jects that you view in convex mirror.
(cid:84) Adjusting mirrors
Instruments and controls
OM-U2737
To adjust the mirrors by hand, push where indicated by the arrows. (cid:84) Remote control mirror switch The remote control mirrors operate only when the ig- nition switch is in the “ON” or “ACC” position.
UB4004BB
1) Selection switch 2) Direction control switch 1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation. The mirrors can also be adjusted manually.
– CONTINUED – 3-31
The indicator light located on the button will come on when the outside mirror defogger heater in operation. To turn it off, push the button again.
Instruments and controls
(cid:84) Outside mirror defogger (if equipped)
To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position.
UB4004CB
1) Indicator light To turn on the outside mirror defogger, push the but- ton while the engine is running.
3-32
Tilt steering wheel
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.
Instruments and controls
place. 5. Make sure that the steering wheel is securely locked by moving it up and down.
HS3043BA
1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in
– CONTINUED – 3-33
Instruments and controls
Horn
To sound the horn, push the horn pad.
HS3044BA
3-34
Climate control
Manual heating and air conditioning
Ventilator ....................................................... 4-2
Driver’s side ventilators ................................... 4-2
Center ventilators ............................................. 4-2
Front passenger’s side ventilators ................. 4-3
Air flow selection .............................................. 4-4
system ........................................................ 4-5
Control panel ..................................................... 4-5
Heater operation ............................................... 4-7
Air conditioner operation ................................. 4-10
Operating tips for heater and air conditioner ................................................. 4-11
Air filtration system (if equipped) ................ 4-134-1
Climate control
Climate controlVentilator (cid:132) Driver’s side ventilators
(cid:132) Center ventilators
UB4038BB
Move the thumb-wheel up and down or right and left to adjust the flow direction.
UB4039BA
1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.
4-2
(cid:132) Front passenger’s side ventilators
UB4040BB
1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.
Climate control
– CONTINUED – 4-3
Climate control
(cid:132) Air flow selection
4-4
UB4036BA
Manual heating and air conditioning system (cid:132) Control panel
UB5004BC
1) Temperature control dial 2) Fan speed control dial 3) Air flow control dial 4) Air conditioner button 5) Air inlet selection button 6) Rear window defogger button (Refer to “Rear window
defogger button” in chapter 3.)
(cid:84) Temperature control dial This dial regulates the temperature of air flow from the
Climate control
air outlets over a range from the blue area (cool) to red area (warm). (cid:84) Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. (cid:84) Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets
and the foot outlets.
: Air flows through the foot outlets and some
through the windshield defroster outlets.
: Air flows through the windshield defroster outlets
and foot outlets.
: Air flows through the windshield defroster out-
lets.
– CONTINUED – 4-5
Climate control
” or “
NOTE When the dial is placed in the “ ” po- sition, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quick- ly. At the same time, the air inlet selection is auto- matically set to “Outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button. (cid:84) Air conditioner button
Push the air conditioner button while the fan is in op- eration to turn on the air conditioner. The indicator light will come on. Push it again to turn off the air conditioner. (cid:84) Air inlet selection button
Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
The air conditioner operates only when the engine is running.
UG4507BA
4-6
UB4041BA
ON position (Recirculation): Interior air is recirculat- ed inside the vehicle. Push the air inlet selection but- ton to the ON position. The indicator light will come on. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selec- tion button again to the OFF position. The indicator light will go off. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temper- ature and the road is no longer dusty.
Climate control
(cid:132) Heater operation (cid:84) Defrosting or defogging the windshield
UB5011AA
”.
To direct warm air to the windshield and front door win- dows: 1. Set the air flow control dial to “ 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the – CONTINUED – 4-7
Climate control
” position.
“ (cid:84) Heating and defrosting
(cid:84) Heating
UB5013AA
UB5012AA
”.
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to “ 2. Set the temperature control dial to the desired tem- perature level. 3. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
”.
To direct warm air toward the floor: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial to the desired tem- perature level. 4. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
4-8
(cid:84) Bi-level heating
Climate control
ference between the air from the instrument panel out- lets and the air from the foot outlets. (cid:84) Ventilation
UB5014AA
This setting allows you to direct air of different temper- atures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial to the desired tem- perature level. 4. Set the fan speed control dial to the desired speed. Setting the temperature control dial fully turned to the red area or blue area decreases the temperature dif-
”.
UB5015AA
To force outside air through the instrument panel out- lets: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed. When driving on a dusty road, set the air inlet control button to the “ON” position.
”.
– CONTINUED – 4-9
Climate control
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
(cid:132) Air conditioner operation (cid:84) Cooling or dehumidifying
compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection button to the “OFF” posi- tion. 2. Set the air flow control dial to “ 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue area. 5. Set the fan speed control dial at the desired speed. (cid:84) Defrosting or defogging
”.
UB5016BB
1) ON position For cooling and dehumidification of the passenger
UB5011BB
1) ON position To direct warm air to the windshield and front door win- dows: 1. Set the air outlet control dial to “
”.
4-10
2. Set the temperature control dial to the red area. 3. Set the fan speed control dial at the highest speed.
Climate control
Operating tips for heater and air con- ditioner (cid:84) Cleaning ventilator grille
UB4037BA
Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any ac- cumulation of insects and leaves on the condenser. (cid:84) Efficient cooling after parking in direct sunlight After parking in direct sunlight, drive with the windows
– CONTINUED – 4-11
(cid:84) Air conditioner compressor shut-off when en-
gine is heavily loaded
To improve acceleration and gas mileage, the air con- ditioner compressor is designed to temporarily shut off during air conditioner operation whenever the acceler- ator is fully depressed such as during rapid accelera- tion or when driving on a steep upgrade. (cid:84) Refrigerant for your climate control system Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Climate control
open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency. (cid:84) Lubrication oil circulation in the refrigerant cir-
cuit
Operate the air conditioner compressor at a low en- gine speed (at idle or low driving speeds) a few min- utes each month during the off-season to circulate its oil. (cid:84) Checking air conditioning system before sum-
mer season
Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer. (cid:84) Cooling and dehumidifying in high humidity
and low temperature weather condition
Under certain weather conditions (high relative humid- ity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
4-12
Air filtration system (if equipped) If your vehicle’s air conditioning system is equipped with a optional air filtration system, replace the filter el- ement according to the replacement schedule shown below. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more frequently. Have your filter checked or replaced by your SUBARU dealer.
Replacement schedule:
Every 12 months or 9,300 miles (15,000 km) whichev- er comes first
NOTE The filter can influence the air conditioning, heat- ing and defroster performance if not properly maintained.
Climate control
– CONTINUED – 4-13
Audio
Antenna system ............................................ Pillar mounted antenna (Non-turbo models) .. Roof mounted antenna (Turbo models) ......... FM reception ..................................................... Installation of accessories ........................... Audio set ........................................................ Type A audio set ............................................... Type B audio set ............................................... In-dash 6 CD auto changer (Optional audio unit – if equipped) ............... AM/FM radio with CD player ........................ Radio operation ................................................ Compact disc player operation ....................... CD changer control (if optional in dash CD changer is connected) ...................................
5-2
5-2
5-2
5-3
5-4
5-4
5-4
5-5
5-5
5-6
5-6
5-11
5-13
Type B audio set (if equipped) ..................... 5-17
5-17
5-23
In-dash 6 CD auto changer (if equipped) .... 5-27
Precautions to observe when handling a compact disc .......................................... 5-30Radio operation ................................................ Built-in CD changer operation .........................
5-1
Audio
AudioAntenna system (cid:132) Pillar mounted antenna (Non-turbo
models)
(cid:132) Roof mounted antenna (Turbo models)
Pull the antenna out to extend it to its full length.
UB5070BA
5-2
UB5073BA
UB5074BA
Stand the roof antenna up for use. You can detach the roof antenna by turning it counterclockwise. When fit- ting the roof antenna, turn it clockwise and tighten it securely.
When working on the cargo bed, be careful not to get poked in the eye by the roof antenna.
NOTE (cid:121) Detach the roof antenna before putting the vehi- cle in a garage and before washing it in an auto- matic car wash. (cid:121) After detaching the roof antenna, keep the mounting hole free of dirt and dust. If any dirt or dust sticks to the hole, remove it before attaching the roof antenna. (cid:121) When detaching the roof antenna, grasp and turn the roof antenna at the base. (cid:121) To avoid damaging the roof antenna, be careful not to overtighten it when attaching it. (cid:121) Radio reception is not possible with the roof an- tenna folded down. Also, reception deteriorates if metallic objects are placed near the roof antenna.
Audio
(cid:132) FM reception Although FM is normally static free, reception can be affected by the surrounding area, atmospheric condi- tions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary stat- ic, flutter or station interference. If reception continues to be unsatisfactory, switch to a stronger station.
– CONTINUED – 5-3
Audio
Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly in- stalled or if they are not suited for the vehicle.
Audio set Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in this sec- tion for operating details.
(cid:132) Type A audio set
UB5066AA
(cid:121) Radio operation: refer to page 5-6 (cid:121) CD (compact disc) player operation: refer to page 5- 11 (cid:121) CD changer control: refer to page 5-13
5-4
(cid:132) Type B audio set
(cid:132) In-dash 6 CD auto changer (Optional
audio unit – if equipped)
Audio
(cid:121) Radio operation: refer to page 5-17 (cid:121) Built-in CD changer operation: refer to page 5-23
UB5075AA
HS5011AA (cid:121) Inserting and removing a disc or all discs: refer to page 5-27
