2009 Saab 9 7X Owners Manual

Download PDF Manual
Storage Areas ................................................2-43 Glove Box ...................................................2-43 Cupholders ..................................................2-43 Overhead Console ........................................2-44 Center Console Storage .................................2-44 Luggage Carrier ...........................................2-44 Rear Floor Storage Cover ..............................2-45 Cargo Cover ................................................2-46 Cargo Tie Downs ..........................................2-47 Moonroof .......................................................2-47 2-2 Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window. Do not leave the keys in a vehicle with children. This vehicle has double-sided keys that can be used for the ignition and door lock. When a new vehicle is delivered, the dealer/retailer provides the owner with a pair of identical keys and a key code number. 2-3 If you ever lock your keys in the vehicle, The key code number tells your dealer/retailer or a qualiﬁed locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you will be able to have new ones made easily using this number. Your selling dealer/retailer should also have this number. Notice: you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever do get locked out of your vehicle, call the Roadside Assistance Center. See Roadside Assistance Program on page 7-6. The key cannot be removed from the ignition if your vehicle does not have power. See Ignition Positions on page 2-20 for additional information. Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-4 If there is a decrease in the RKE operating range, try this: (cid:129) Check the distance. The transmitter may be too far from the vehicle. Stand closer during rainy or snowy weather. (cid:129) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:129) Check the transmitter’s battery. See “Battery Replacement” later in this section. If the transmitter is still not working correctly, see your dealer/retailer or a qualiﬁed technician for service. Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 30 feet (9 m) away from the vehicle. The RKE transmitter buttons do not operate when the key is in the ignition. Q (Lock): Press to lock all the doors. Press Q again within three seconds and the horn may chirp. K (Unlock): Press once to unlock the driver door. The parking lamps may ﬂash and the interior lights come on. Press K again and all remaining doors unlock. To program different feedback settings through the Driver Information Center (DIC), see Driver Information Center (DIC) on page 3-42. L (Panic Alarm): Press to sound the horn. The headlamps and taillamps ﬂash for up to 30 seconds. To turn the alarm off, press L again, or wait 30 seconds, or start the vehicle. 2-5 (cid:129) Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen transmitters no longer work once the new transmitter is programmed. Each vehicle can have up to four transmitters programmed to it. Battery Replacement Replace the battery if the KEY FOB # BATTERY LOW message displays in the DIC. See “KEY FOB # BATTERY LOW” under DIC Warnings and Messages on page 3-45. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter. 2-6 To replace the battery: 1. Remove the screw from the back of the RKE cover to open the transmitter. 2. Remove the old battery. Do not use a metal object. 3. Insert the new battery. Replace with a CR2032 or equivalent battery. 4. Assemble the transmitter and replace the screw. Doors and Locks Door Locks { CAUTION: There are several ways to lock and unlock your vehicle. From the outside, use the remote keyless entry transmitter or the key. From the inside, slide the manual lever forward or rearward. Unlocked doors can be dangerous. (cid:129) Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:129) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:129) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. The manual lever on each door works only that door’s lock. 2-7 Five seconds after the last door is closed, all the doors will lock. You can lock the doors immediately by using the power door lock switch or by pressing the lock button on the optional remote keyless entry transmitter a second time. If the key is inserted in the ignition, this feature will not lock the doors. See Lockout Protection on page 2-11. You can turn the delayed locking feature on or off. If the feature is turned off, the doors will lock immediately when a power door lock switch or remote keyless entry transmitter lock button is pressed. Programming Delayed Locking To turn the delayed locking feature on or off, do the following: 1. Press and hold the power door lock switch on the driver’s door in the lock position. 2. Press the remote keyless entry transmitter unlock button twice. If the delayed locking feature was on, it will now be off. If the feature was off, it will now be on. Power Door Locks The power door lock switches are located on the driver’s and front passenger’s door armrests. Press the lock symbol to lock all of the doors. To unlock the doors, press the other side of the switch. Delayed Locking This feature delays the locking of the doors and the liftgate when using the power lock or the remote keyless entry system. The ﬁrst press of the power door lock switch or lock button on the remote keyless entry transmitter with the driver’s door open will activate the delay locking. A chime will sound. All doors and the liftgate can be reopened for up to ﬁve seconds from the time the last door is closed. 2-8 Programmable Automatic Door Locks Your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. See DIC Vehicle Customization on page 3-51. Programmable Locking Feature Following are the two locking modes that can be programmed: Mode 1: All doors lock when the transmission is shifted out of (P) Park. Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h). The automatic door locks were pre-programmed at the factory to lock all the doors when the transmission is shifted into gear. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the two programming options listed previously before entering the program mode. To enter the program mode, do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to ON/RUN and LOCK/OFF twice. Then, with the key in LOCK/OFF, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the two programming options listed previously, and press the lock side of the power door lock switch to cycle through the lock options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to ON/RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. 2-9 Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into (P) Park. Mode 2: All doors unlock when the transmission is shifted into (P) Park. Mode 3: All doors unlock when the key is removed from the ignition. Mode 4: No automatic door unlock. The automatic door locks were pre-programmed at the factory to unlock all doors once the transmission is shifted to (P) Park. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the four programming options listed previously before entering the program mode. To enter the program mode you need to do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to ON/RUN and LOCK/OFF twice. Then, with the key in LOCK/OFF, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the four programming options listed above, and press the unlock side of the power door lock switch to cycle through the unlocking options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to ON/RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. 2-10 Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they cannot be opened from the inside by passengers. To use one of these locks do the following: 1. Open one of the rear doors. You will ﬁnd a security lock lever located on the inside edge of each rear door. 2. Move the lever down to engage the security lock. Move the lever up to disengage the security lock. The rear doors of your vehicle cannot be opened from the inside while this feature is in use. If you want to open the rear door while the security lock is on, unlock the door and open the door from the outside. Lockout Protection This feature stops the power door locks from locking when the key is in the ignition and a door is open to protect you from locking your key in the vehicle. If the power lock switch is pressed when a door is open and the key is in the ignition, all the doors will lock and then the driver’s door will unlock. 3. Close the door. 2-11 Liftgate/Liftglass { CAUTION: It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate or liftglass: (cid:129) Make sure all other windows are shut. (cid:129) Turn the fan on your climate control system to its highest speed and select the control setting that will force outside air into your vehicle. See “Climate Control System” in the Index. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-30. Liftgate Release To unlock the liftgate, use the power door lock switch or the remote keyless entry transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5. The liftglass will also unlock when the liftgate is unlocked. Press the button on the liftglass to open it. To open the entire liftgate, lift the handle located in the center of the liftgate. When the liftgate is opened, the liftglass will lock after a short delay. Emergency Release for Opening Liftgate 1. Remove the trim plug, located on the inside of the liftgate in the center, to expose the access hole in the trim panel. 2. Use a tool to reach through the access hole in the trim panel. 3. Pry the left release lever up to the unlock position. Pry the right release lever up to unlatch the liftgate. 4. Reinstall the trim plug. 2-12 (cid:129) Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-13 Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window. Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows. 2-14 The controls for the power windows are located on the armrest on each of the side doors. With power windows, the switches operate the windows when the ignition is in ON/RUN, ACC/ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-21. The driver’s door also has a switch for each of the passenger’s windows. Press down the top of the switch to lower the window and pull up on the switch to raise the window. If you hold the switch down for three to seven seconds after the window has been completely lowered or raised, the window will not operate for about 15 seconds. Express-Down Window AUTO (Express-down): The driver’s and front passenger’s window switches have an express-down feature that allows you to lower the window without holding the switch down. Press down brieﬂy on the driver’s or front passenger’s window switch labeled AUTO to activate the express-down feature. Lightly tap the switch to open the window slightly. The express-down feature can be interrupted at any time by pressing the top of the switch. Window Lockout o (Lockout): Your vehicle has a lockout feature to prevent passengers from operating the power windows. The lockout switch is located in front of the window switches on the driver’s door. A light in the lockout switch will come on to show that the switch has been activated. Press the lockout switch again to return to normal operation. Sun Visors Sun Visors with Slide Rod Your vehicle may have this feature. Pull the sun visor down to block glare. Detach the sun visor from the center mount and slide it along the rod from side-to-side to cover the driver or passenger side of the front window. Swing the sun visor to the side to cover the side window. It can also be moved along the rod from side-to-side in this position. Sun Visors with Fixed Rod and Pull-out Extension Your vehicle may have this feature. Pull the sun visor down to block glare. Pull the sun visor extender out for additional coverage. Detach the sun visor from the center mount and swing it to the side to cover the side window. Lighted Visor Vanity Mirror Pull the sun visor down and lift the mirror cover to turn on the lamps. The lamps will turn off when the cover is closed. 2-15 Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle is equipped with a content theft-deterrent alarm system. Here is how to operate the system: 1. Open the door. 2. Lock the door with the power door lock switch or the remote keyless entry transmitter. The security light should ﬂash. 3. Close all doors. The security light should turn off after approximately 30 seconds. The alarm is not armed until the security light turns off. If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will ﬂash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power. Remember, the theft-deterrent system will not activate if you lock the doors with a key or use the manual door lock. It activates only if you use a power door lock switch with the door open, or with the remote keyless entry transmitter. You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off. Here is how to avoid setting off the alarm by accident: If you do not want to activate the theft-deterrent system, the vehicle should be locked with the door key after the doors are closed. (cid:129) Always unlock a door with a key, or use the remote keyless entry transmitter. Unlocking a door any other way will set off the alarm. If you set off the alarm by accident, unlock any door with the key. You can also turn off the alarm by pressing unlock on the remote keyless entry transmitter. The alarm will not stop if you try to unlock a door any other way. 2-16 (cid:129) Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter. 3. Get out of the vehicle, close the door and wait for the security light to go out. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm. When the alarm is set the power door unlock switch is not operational. If the alarm does not sound when it should but the headlamps ﬂash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 5-107. If the alarm does not sound or the headlamps do not ﬂash, the vehicle should be serviced by your dealer. PASS-Key® III Electronic Immobilizer Your PASS-Key III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key III uses a radio frequency transponder in the key that matches a decoder in your vehicle. 2-17 PASS-Key® III Electronic Immobilizer Operation Your vehicle is equipped with the PASS-Key III (Personalized Automotive Security System) theft-deterrent system. PASS-Key III is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system. When the PASS-Key III system senses that someone is using the wrong key, it shuts down the vehicle’s starter and fuel systems. The starter will not work and fuel will stop being delivered to the engine. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. When trying to start the vehicle, if the engine does not start and the SECURITY light comes on, there may be a problem with your theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-107. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty. See your dealer/retailer who can service the PASS-Key III to have a new key made. It is possible for the PASS-Key III decoder to learn the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. This procedure is for programming additional keys only. Canadian Owners: If you lose or damage your keys, only a dealer/retailer can service PASS-Key III to have new keys made. To program additional keys you will require two current driver’s keys. You must add a step to the following procedure. After Step 2 repeat Steps 1 and 2 with the second current driver’s key. Then continue with Step 3. 2-18 To program the new key: 1. Verify that the new key has PK3 stamped on it. 2. Insert the current driver’s key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key. 4. Insert the key to be programmed and turn it to ON/RUN within 10 seconds of removing the previous key. 5. The SECURITY light will turn off once the key has been programmed. It may not be apparent that the SECURITY light went on due to how quickly the key is programmed. 6. Repeat Steps 1 through 4 if additional keys are to be programmed. If you are ever driving and the SECURITY light comes on and stays on, you will be able to restart your engine if you turn it off. Your PASS-Key III system, however, is not working properly and must be serviced by your dealer/ retailer. Your vehicle is not protected by the PASS-Key III system at this time. If you lose or damage a PASS-Key III key, see your dealer/retailer to have a new key made. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:129) Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km). (cid:129) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake or slow the vehicle. (cid:129) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:129) Do not tow a trailer during break-in. See Towing a Trailer on page 4-29 for the trailer towing capabilities of the vehicle and more information. Following break-in, engine speed and load can be gradually increased. 2-19 Ignition Positions The ignition switch is located on the center console, and has four different positions. In order to shift out of P (Park), turn the ignition to ON/RUN and apply the brake pedal. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer. 9 (LOCK/OFF): This position locks the ignition and transmission. The key can only be removed when the ignition switch is in LOCK/OFF and the vehicle has power. 2-20 The steering wheel can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY. If this doesn’t work, then the vehicle needs service. ACC (ACC/ACCESSORY): This position can be used to operate the electrical accessories. R (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The switch stays in this position when the engine is running. If you leave the key in the ACC/ACCESSORY or ON/RUN position with the engine off, the battery could be drained. You may not be able to start the vehicle if the battery is allowed to drain for an extended period of time. / (START): This position starts the engine. When the engine starts, release the key. The ignition switch returns to ON/RUN for driving. A warning tone will sound when the driver door is opened, the ignition is in ACC/ACCESSORY or LOCK/OFF and the key is in the ignition. Retained Accessory Power (RAP) These vehicle accessories may be used for up to 10 minutes after the engine is turned off: (cid:129) Audio System (cid:129) DVD Player (cid:129) Power Windows (cid:129) Overhead console (cid:129) Sunroof (if equipped) These features work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF, these features will continue to work up to 10 minutes or until a door is opened. Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the engine when the vehicle is already moving, use N (Neutral) only. Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to START. When the engine starts, let go of the key. The idle speed will slow down as the engine warms. Do not race the engine immediately after starting it. Operate the engine and transmission gently to allow the oil to warm up and lubricate all moving parts. The vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START, cranking will be stopped after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Engine cranking can be stopped by turning the ignition switch to the ACC/ACCESSORY or LOCK/OFF position. Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down. 2-21 Adjustable Throttle and Brake Pedal If the vehicle has this feature, you can change the position of the throttle and brake pedals. The vehicle must be in P (Park) for this feature to operate. The switch used to adjust the pedals is located on the steering column. Press the switch forward or backward to move the pedals closer or farther away from you. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, repeat these steps. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts. Notice: The engine is designed to work with the electronics in the vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer/retailer. If you do not, the engine might not perform properly. Any resulting damage would not be covered by the vehicle warranty. 2-22 Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F (−18°C). Vehicles with an engine coolant heater should be plugged in at least four hours before starting the vehicle. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above 0°F (−18°C). To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver side of the engine compartment next to the battery box facing the engine. 3. Plug it into a normal, grounded 110-volt AC outlet. { CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts and prevent damage. The length of time the heater should remain plugged in depends on several factors. Ask a dealer/retailer in the area where you will be parking the vehicle for the best advice on this. 2-23 Active Fuel Management™ If the vehicle has a 5.3L V8 engine, it has Active Fuel Management™. This system allows the engine to operate on either all or half of its cylinders, depending on driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing the vehicle to achieve better fuel economy. When greater power is required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain full-cylinder operation. Automatic Transmission Operation There are several different positions for the gear shift lever. P (Park): This position locks the rear wheels. It is the best position to use when you start the engine because the vehicle cannot move easily. { CAUTION: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). See Shifting Into Park on page 2-28. If you are pulling a trailer, see Towing a Trailer on page 4-29. Make sure the shift lever is fully in P (Park) before starting the engine. The vehicle has an automatic transmission shift lock control system. You have to apply the brake pedal then press the shift lever button before you can shift from P (Park) when the ignition key is in ON/RUN. 2-24 If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 2-29. R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-20. N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only. { CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, the vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed. Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle. D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: (cid:129) Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:129) Going about 35 mph (55 km/h) or more, push the accelerator all the way down. The vehicle will shift down to the next gear and have more power. 2-25 Downshifting the transmission in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 4-12. D (Drive) can be used when towing a trailer, carrying a heavy load, driving on steep hills, or for off-road driving. You may want to shift the transmission to 3 (Third) or, if necessary, a lower gear selection if the transmission shifts too often. 3 (Third): This position is also used for normal driving. It reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill. To shift to the 3 (Third) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter to the 3 (Third) position. 2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. You can use 2 (Second) on hills. It can help you control vehicle speed as you go down steep mountain roads, while using the brakes off and on. To shift to the 2 (Second) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter to the 2 (Second) position. You can also use 2 (Second) for starting the vehicle from a stop on slippery road surfaces. 1 (First): This position reduces vehicle speed even more than 2 (Second) without using the brakes. You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in 1 (First) while the vehicle is moving forward, the transmission will not shift into ﬁrst gear until the vehicle is going slowly enough. To shift to the 1 (First) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter to the 1 (First) position. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. 2-26 Parking Brake To set the parking brake, hold the regular brake pedal down with your foot and pull up on the parking brake lever located between the seats. To release the parking brake, hold the regular brake pedal down. Pull the parking brake lever up until you can press in the button at the end of the lever. Hold the button in as you move the parking brake lever all the way down. If the ignition is on, the brake system warning light on the instrument panel cluster will come on. See Brake System Warning Light on page 3-31. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and you must park on a hill, see Towing a Trailer on page 4-29. 2-27 Shifting Into Park { CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-29. 1. Hold the brake pedal down and set the parking brake. See Parking Brake on page 2-27 for more information. 2. Move the shift lever into P (Park) by pressing the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to LOCK/OFF. 4. Remove the key and take it with you. If you can leave the vehicle with the key, the vehicle is in P (Park). 2-28 Leaving the Vehicle With the Engine Running { CAUTION: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave the vehicle with the engine running. If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Park) and the parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into P (Park), hold the regular brake pedal down. Then, see if you can move the shift lever away from P (Park) without ﬁrst pressing the button on the console shift lever. If you can, it means that the shift lever was not fully locked into P (Park). Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into P (Park) properly before you leave the driver seat. To ﬁnd out how, see Shifting Into Park on page 2-28. When you are ready to drive, move the shift lever out of P (Park) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of P (Park). Shifting Out of Park The vehicle has an electronic shift lock release system. The shift lock release is designed to: (cid:129) Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and (cid:129) Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN and the regular brake pedal is applied. The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery. If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 5-43 for more information. To shift out of P (Park) use the following: 1. Apply the brake pedal. 2. Press the shift lever button. 3. Move the shift lever to the desired position. If you still are unable to shift out of P (Park): 1. Fully release the shift lever button. 2. Hold the brake pedal down and press the shift lever button again. 3. Move the shift lever to the desired position. If you still cannot move the shift lever from P (Park), consult your dealer/retailer or a professional towing service. 2-29 Parking Over Things That Burn CAUTION: (Continued) { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. CAUTION: (Continued) 2-30 Exhaust may enter the vehicle if: (cid:129) The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes). (cid:129) The exhaust smells or sounds strange or different. damage. (cid:129) The exhaust system leaks due to corrosion or (cid:129) The vehicle’s exhaust system has been modiﬁed, damaged or improperly repaired. (cid:129) There are holes or openings in the vehicle body from damage or after-market modiﬁcations that are not completely sealed. If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle: (cid:129) Drive it only with the windows completely down. (cid:129) Have the vehicle repaired immediately. Never park the vehicle with the engine running in an enclosed area such as a garage or a building that has no fresh air ventilation. Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 2-30. It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure the vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to P (Park). Follow the proper steps to be sure the vehicle will not move. See Shifting Into Park on page 2-28. If parking on a hill and pulling a trailer, see Towing a Trailer on page 4-29. 2-31 Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming rearview mirror with a compass display. O (On/Off): Press to turn the dimming feature on or off. Automatic Dimming Mirror Operation Automatic dimming reduces the glare of lights from behind the vehicle. The dimming feature comes on and the indicator light illuminates each time the vehicle is started. Cleaning the Mirror Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water. Compass Compass Operation There is a compass display on the upper right corner of the mirror. Press O to turn the compass display on or off. Compass Calibration Press and hold O to activate the compass calibration mode. CAL displays in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder, or similar object. If CAL appears in the compass window, the compass may need to be reset or calibrated. 2-32 Compass Variance The mirror is set to zone eight. Adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, such as during a long distance cross-country trip, it is necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold O until the zone number displays. The number shown is the current zone number. 3. Scroll through the zone numbers that appear in the window on the mirror by pressing the O button. Once you ﬁnd your zone number, release the button. After about four seconds, the mirror returns to the compass display, and the new zone number is set. If CAL appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. 2-33 Outside Power Mirrors The outside power mirror control is located on the driver’s door. 1. Turn the knob toward the mirror you desire to adjust. 2. Move the control in the direction you want the mirror to go. 3. Adjust the mirror in all four directions to see the side of your vehicle and the area behind your vehicle. 4. After adjusting each mirror, turn the control to the center position so the mirror cannot be moved. If you reach the mirror’s end of the travel position in any direction, the mirror enters a ratcheting mode. This action is harmless. It is a warning that the mirror can go no further. To stop this action, back the mirror up by moving the control in the opposite direction. 2-34 Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position. Outside Convex Mirror { CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes. The passenger side mirror is convex shaped. A convex mirror’s surface is curved so more can be seen from the driver seat. Outside Heated Mirrors For vehicles with heated mirrors: < (Rear Defogger): Press to heat the mirrors. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-19. OnStar® System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If the keys are locked in the vehicle, call OnStar at 1-888-4-ONSTAR to have a signal sent to unlock the doors. OnStar Hands-Free Calling, including 30 trial minutes good for 60 days, is available on most vehicles. OnStar Turn-by-Turn Navigation service, with one trial route, is available on most vehicles. Press the OnStar button to have an OnStar advisor contact Roadside Service. OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar. After the ﬁrst prepaid year, contact OnStar to select a monthly or annual subscription payment plan. If a payment plan is not selected, the OnStar system and all services, including airbag notiﬁcation and emergency services, may be deactivated and no longer available. For more information visit www.onstar.com (U.S.) or www.onstar.ca (Canada), or press the OnStar button to speak with an advisor. Not all OnStar services are available on all vehicles. To check if this vehicle is able to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in the glove box or visit www.onstar.com (U.S.) or www.onstar.ca (Canada), contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. 2-35 OnStar Services Available with the Safe & Sound Plan (cid:129) Automatic Notiﬁcation of Airbag Deployment (cid:129) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) Link to Emergency Services (cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostic Email (cid:129) Remote Diagnostics (cid:129) OnStar Hands-Free Calling with 30 trial minutes (cid:129) OnStar Virtual Advisor (U.S. Only) OnStar Services Included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) OnStar Turn-by-Turn Navigation (If equipped) or Driving Directions - Advisor delivered (cid:129) RideAssist Information and Convenience Services 2-36 OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days. Hands-Free Calling can also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Turn-by-Turn Navigation Vehicles with the OnStar Turn-by-Turn Navigation system can provide voice-guided driving directions. Press the OnStar button to have an OnStar advisor locate a business or address and download driving directions to the vehicle. Voice-guided directions to the desired destination will play through the audio system speakers. See the OnStar Owner’s Guide for more information. (cid:129) (cid:129) OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics. See the OnStar Owner’s Guide for more information. This feature is only available in the continental U.S. OnStar Steering Wheel Controls This vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-97 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information. How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy. This information usually includes the vehicles GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicles GPS location so they can provide services where it is located. OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless the vehicle is in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. 2-37 Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place. Some examples are damage to important parts of the vehicle in a crash, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the volume of the radio if the OnStar advisor cannot be heard. If the light next to the OnStar buttons is red, the system may not be functioning properly. Press the OnStar button and request a vehicle diagnostic. If the light appears clear (no light is appearing), your OnStar subscription has expired and all services have been deactivated. Press the OnStar button to conﬁrm that the OnStar equipment is active. Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-38 Universal Home Remote System Operation (With One Triangular LED) If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate that is being programmed. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. 2-39 Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated. To program up to three devices: 1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2-40 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require substitution of Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light on the Universal Home Remote will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and the garage door should move when the Universal Home Remote button is pressed and released. There is no need to continue programming Steps 6 through 8. If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person assist with the remaining steps. 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 2-41 Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 2-42 Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. 2. Release both buttons. Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-6. Storage Areas Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box. Cupholders A cupholder is located on the instrument panel next to the radio. To open the cupholder, push once on the support and the cupholder will move into position for use. To close the cupholder, lift the support up towards the instrument panel. A cupholder is located on the front of the center console and two more are located at the rear of the center console. To use the rear cupholders, pull down on the lid. 2-43 Overhead Console For this vehicles with this feature, the overhead console may include reading lamps, a Universal Home Remote, and a moonroof switch. See the following for more information: (cid:129) Reading Lamps on page 3-17. (cid:129) Universal Home Remote System on page 2-38. (cid:129) Moonroof on page 2-47. Center Console Storage Grasp the front lever on the center console while lifting the top to open it. The console may contain one or more of the following components: (cid:129) Rear Seat Audio Controls. See Rear Seat Audio (RSA) on page 3-95. (cid:129) Rear Climate Control. See Rear Climate Control System on page 3-23. (cid:129) Accessory Power Outlets. See Accessory Power Outlet(s) on page 3-18. Ignition Switch. See Ignition Positions on page 2-20. For vehicles with the center armrest compartment, pull up on the latch handle located underneath the front edge to lift the cover. 2-44 Luggage Carrier { CAUTION: If something is carried on top of the vehicle that is longer or wider than the luggage carrier — like paneling, plywood, or a mattress — the wind can catch it while the vehicle is being driven. This can cause a driver to lose control. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle. Items may be carried inside. Never carry something longer or wider than the luggage carrier on top of the vehicle. The vehicle may be equipped with a luggage carrier that allows things to be loaded on top of the vehicle. The luggage carrier, if equipped, has side rails attached to the roof, and places to use for tying things down. These allow for thing to be loaded on the vehicle, as long as they are not wider or longer than the luggage carrier. (cid:129) Crossrails can be purchased from your dealer/retailer. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle can damage the vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 4-21. To prevent damage or loss of cargo while driving, check now and then to make sure the luggage carrier is locked and cargo is still securely fastened. When the luggage carrier is not in use, place the crossrails at the following positions for reduced wind noise. Place one crossrail at the rear most point of the vehicle and the other crossrail above the opening of the rear door. Rear Floor Storage Cover { CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. The vehicle has a rear cargo area with a removable storage cover. To remove the rear ﬂoor storage cover, do the following: 1. Press the latch release and lift up the latch handle. 2. Raise the cover slightly to unhook it. 3. Pull the cover towards the rear of the vehicle to release it from the forward mounting slots. To reinstall the rear ﬂoor storage cover, reverse the previous steps. Make sure the cover is secure by applying slight pressure to the latch until it clicks. 2-45 Cargo Cover The cargo cover can be used to cover items in the cargo area of the vehicle. To install the cargo cover, do the following: 1. Align the endcap with the pocket in the trim panel located behind the rear seat. 2. Squeeze the opposite endcap, align it with the pocket located on the opposite side of the trim panel and release. 3. Grasp the handle and unroll the cover. Latch the posts into the sockets on the inside of the vehicle to secure it. To remove the cargo cover, do the following: 1. Release the cover from the latch posts and carefully roll it back up. 2. Squeeze one endcap and remove it from the pocket in the trim panel. 3. Remove the cargo cover from the other endcap so that the shade can be removed from the vehicle. { CAUTION: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. Someone could be injured. If the cover is removed, always store it in the proper storage location. When it is replaced, always be sure that it is securely reattached. 2-46 Cargo Tie Downs Four cargo tie-downs are located in the rear compartment of the vehicle. The tie-downs can be used to secure small loads. Moonroof The vehicle may be equipped with a power sliding moonroof. The ignition must be turned to ON/RUN, ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active to operate it. See Retained Accessory Power (RAP) on page 2-21. The moonroof switch is located in the overhead console. Press and release the back of the button to open the moonroof. Press and hold the front of the button to close the moonroof. With the moonroof closed, press the front of the button to open the moonroof to the vent position. The moonroof has a sunshade which can be pulled forward to block sun rays. If the sunshade is in the closed position, it will open when the moonroof is opened. 2-47 ✍ NOTES 2-48 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-6 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..................3-7 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-8 Windshield Washer .........................................3-9 Rear Window Wiper/Washer .............................3-9 Headlamp Washer ........................................3-10 Cruise Control ..............................................3-10 Headlamps ..................................................3-13 Headlamps on Reminder ................................3-14 Daytime Running Lamps (DRL) .......................3-14 Automatic Headlamp System ..........................3-14 Fog Lamps ..................................................3-15 Instrument Panel Brightness ...........................3-16 Dome Lamps ...............................................3-16 Dome Lamp Override ....................................3-16 Entry Lighting ...............................................3-16 Exit Lighting .................................................3-17 Reading Lamps ............................................3-17 Electric Power Management ...........................3-17 Battery Run-Down Protection ..........................3-18 Accessory Power Outlet(s) .............................3-18 Climate Controls ............................................3-19 Dual Automatic Climate Control System ...........3-19 Outlet Adjustment .........................................3-23 Rear Climate Control System .........................3-23 Climate Controls Personalization .....................3-24 Warning Lights, Gages, and Indicators ............3-24 Instrument Panel Cluster ................................3-25 Speedometer and Odometer ...........................3-26 Trip Odometer ..............................................3-26 Tachometer .................................................3-26 Safety Belt Reminders ...................................3-27 Airbag Readiness Light ..................................3-28 Passenger Airbag Status Indicator ...................3-29 Charging System Light ..................................3-30 Voltmeter Gage ............................................3-30 Brake System Warning Light ..........................3-31 Antilock Brake System (ABS) Warning Light .....3-32 StabiliTrak® Service Light ...............................3-32 StabiliTrak® Indicator Light .............................3-33 Engine Coolant Temperature Gage ..................3-33 3-1 Section 3 Instrument Panel Tire Pressure Light .......................................3-34 Malfunction Indicator Lamp .............................3-34 Oil Pressure Gage ........................................3-37 Security Light ...............................................3-38 Cruise Control Light ......................................3-38 Reduced Engine Power Light .........................3-39 Highbeam On Light .......................................3-39 Service All-Wheel Drive Light .........................3-40 Check Gages Warning Light ...........................3-40 Gate Ajar Light .............................................3-40 Fuel Gage ...................................................3-41 Low Fuel Warning Light .................................3-41 Check Gas Cap Light ....................................3-41 Driver Information Center (DIC) .......................3-42 DIC Operation and Displays ...........................3-42 DIC Warnings and Messages .........................3-45 DIC Vehicle Customization .............................3-51 Audio System(s) .............................................3-57 Setting the Clock ..........................................3-57 Radio(s) ......................................................3-58 Using an MP3 ..............................................3-68 XM Radio Messages .....................................3-72 Navigation/Radio System ...............................3-74 Bluetooth® ...................................................3-74 Rear Seat Entertainment (RSE) System ...........3-84 Rear Seat Audio (RSA) .................................3-95 Theft-Deterrent Feature ..................................3-97 Audio Steering Wheel Controls .......................3-97 Radio Reception ...........................................3-98 Fixed Mast Antenna ......................................3-99 XM™ Satellite Radio Antenna System .............3-99 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-23. B. Turn Signal/Multifunction Lever on page 3-6. C. Audio Steering Wheel Controls on page 3-97. D. Instrument Panel Cluster on page 3-25. E. Windshield Wipers on page 3-8. F. Hazard Warning Flashers on page 3-6 or Driver Information Center (DIC) on page 3-42. G. Windshield Washer on page 3-9. H. Instrument Panel Brightness on page 3-16. I. Hood Release on page 5-11. J. Dome Lamp Override on page 3-16. K. Adjustable Throttle and Brake Pedal on page 2-22. L. Tilt Wheel on page 3-6. M. Horn on page 3-6. N. Audio System(s) on page 3-57. O. Dual Automatic Climate Control System on page 3-19. P. Shift Lever. See Automatic Transmission Operation on page 2-24. Q. Ignition Positions on page 2-20. R. Parking Brake on page 2-27. S. Accessory Power Outlet(s) on page 3-18. T. Cupholders on page 2-43. U. Glove Box on page 2-43. 3-5 Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press | again to turn the ﬂashers off. Horn To sound the horn, press the horn symbols on the steering wheel pad. Tilt Wheel The tilt lever is on the outboard side of the steering column, under the turn signal lever. Hold the steering wheel and pull the lever toward you to change the position, then release the lever to lock. Do not adjust the steering wheel while driving. 3-6 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals O : Headlamps 2 3 : Headlamp High/Low Beam-Changer # : Fog Lamps I : Cruise Control Flash-To-Pass Feature. Information for these features is on the pages following. Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change. Hold it there until the lane change is complete. The lever returns to its starting position when it is released. If after signaling a turn or lane change the arrows ﬂash rapidly or do not come on, a signal bulb could be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 5-107. If the vehicle has a trailer towing option with added wiring for the trailer lamps, a turn signal ﬂasher is used. With this ﬂasher installed, the signal indicator ﬂashes even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working. Turn Signal On Chime A chime sounds if the turn signal has been on 3/4 of a mile (1.2 km). Move the turn signal lever to off. Headlamp High/Low-Beam Changer To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. 3-7 Flash-to-Pass This feature lets high-beam headlamps be used to signal to a driver in front of you that you want to pass. It works even if the headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, the high-beam headlamps turn on. They will stay on as long as the lever is held toward you. The high-beam indicator on the instrument panel cluster comes on. Release the lever to return to normal operation. Windshield Wipers The windshield wiper lever is located on the right side of the steering column. Move the lever to control the windshield wipers. 3-8 7 (Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. Hold the lever down longer for more wipe cycles. 9 (Off): Turns off the wipers. & (Delay): Sets a delay between wipes. Turn the delay adjustment band to set the length of the delay. x (Delay Adjustment): Use this band to set the length of the delay between wipes when using the delay feature. The closer the band is moved toward mist, the longer the delay. The windshield wiper lever must be in delay for this feature to work. 6 (Low Speed): For steady wiping at low speed. 1 (High Speed): For wiping a high speed. If the windshield wipers are in use for about six seconds while you are driving, the exterior lamps will come on automatically if the exterior lamp control is in AUTO. Clear ice and snow from the wiper blades before using them. If the wiper blades are frozen to the windshield, gently loosen or thaw them. If they become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-56. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Windshield Washer L (Windshield Washer): Press the windshield washer paddle to spray washer ﬂuid on the windshield. The wipers will clear the window and then either stop or return to the preset speed. { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Rear Window Wiper/Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The rear window wiper/ washer control is located to the left of the steering wheel on the instrument panel. To turn the rear wiper on, turn the control to either 1, 2, or 3. For delayed wiping, turn the control to 1 or 2. For steady wiping, turn the control to 3. To turn the wiper off, turn the control to 0. To wash the rear window, press = located in the center of the control. The rear window washer uses the same ﬂuid bottle as the windshield washer. However, the rear window washer will run out of ﬂuid before the windshield washer. If windshield can be washed, but not the rear window, check the ﬂuid level. 3-9 Headlamp Washer For vehicles with headlamp washers, they clear debris from the headlamp lenses by soaking the lens with ﬂuid, waiting for about ﬁve seconds, then rinsing away the loose debris. The headlamp washers are located under the headlamps. The headlamp washers activate for one wash-wait-rinse cycle when the front windshield washer button is pressed for the ﬁrst time after the vehicle is turned on. The headlamps washers then activate automatically for one cycle after every four front windshield washes. The headlamps must be on to be washed. If the headlamps are off, only the front windshield will be washed. The headlamp washers use the same ﬂuid bottle as the windshield washer. However, the headlamp washers will run out of ﬂuid before the windshield washer. If the windshield can be washed, but not the headlamps, check the ﬂuid level. See Windshield Washer on page 3-9 for more information. Cruise Control With cruise control, a speed of about 25 mph (40 km/h) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 25 mph (40 km/h). If the brakes are applied, the cruise control shuts off. { CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. 3-10 The cruise controls are located on the end of the turn signal/multifunction lever. Setting Cruise Control { CAUTION: R (On): Turns the system on. + (Resume/Accelerate): Makes the vehicle accelerate or resume to a previously set speed. T (Set): Press this button to set the speed. 9 (Off): Turns the system off. If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to R . 2. Get up to the desired speed. 3. Press T at the end of the lever and release it. 4. Take your foot off the accelerator pedal. Some vehicles have a cruise light on the instrument panel cluster that comes on when the cruise control is engaged. 3-11 Resuming a Set Speed Suppose the cruise control is set at a desired speed and then the brakes are applied. This disengages the cruise control. But it does not need to be reset. Once the vehicle is going about 25 mph (40 km/h) or more, move the cruise control switch brieﬂy from R to S . The vehicle returns to the chosen speed and stays there. If the switch is held at resume/accelerate the vehicle will keep going faster until the switch is released or the brake is applied. So unless you want the vehicle to go faster, do not hold the switch at resume/accelerate. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:129) Use the accelerator pedal to get to the higher speed. Press T at the end of the lever, then release the button and the accelerator pedal. The vehicle will now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:129) Move the cruise switch from R to S . Hold it there until the desired speed is reached, and then release the switch. To increase the vehicle speed in small amounts, move the switch brieﬂy to resume/accelerate. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control (cid:129) Press in the button at the end of the lever until the lower desired speed is reached, then release it. To slow down in very small amounts, brieﬂy press the set button. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle will slow down to the cruise control speed set earlier. Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle’s speed, load and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s 3-12 (cid:129) speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle’s speed down. When the brakes are applied this disengages the cruise control. Ending Cruise Control To turn off the cruise control, do one of the following: (cid:129) Step lightly on the brake pedal, (cid:129) move the cruise control switch to 9, or shift the transmission to N (Neutral). If your vehicle has the StabiliTrak feature, cruise control will turn off if road conditions cause StabiliTrak to activate. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. The cruise control will turn off automatically if the traction control system or StabiliTrak system activate, if your vehicle has either feature. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. See Turn Signal/Multifunction Lever on page 3-6. O (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has the following four positions: O (On/Off): Turns off the Daytime Running Lamps (DRL) and Automatic Headlamps. Turning the control to this position again turns the automatic lighting system back on. This feature is not available for vehicles ﬁrst sold in Canada. AUTO (Automatic): Automatically turns the exterior lamps on and off depending upon how much light is available outside of the vehicle. ; (Parking Lamps): Turns on the parking lamps together with the following: (cid:129) Sidemarker Lamps Taillamps License Plate Lamps Instrument Panel Lights

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Saab 9 7X Owners Manual