WARNING
c Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
c During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.
c Your vehicle(cid:146)s engine should be turned off while programming the HomeLinkT Universal Transceiver.
Type A
LIC0671
PROGRAMMING HOMELINKT 1. To begin, press and hold the two outer HomeLinkT buttons (to clear the memory) until the indicator light s1 blinks slowly (after 20 seconds). Release both buttons.
2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface.
Instruments and controls 2-51
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LIC0670
LIC0677
LIC0676
Type B
Type A
3. Using both hands, simultaneously press and hold both the HomeLinkT button you want to program and the hand-held transmitter but- ton.
DO NOT release the buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a (cid:147)slow blink(cid:148) to a (cid:147)rapidly flashing blink(cid:148). This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro- grammed device, press and hold the pro- grammed HomeLinkT button (cid:151) releasing when the device begins to activate.
Type B
5.
If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a (cid:147)rolling code(cid:148) garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another per- son for convenience.
2-52 Instruments and controls
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
all
previously
NOTE: Do not repeat step 1 unless you want to (cid:147)clear(cid:148) programmed HomeLinkT buttons. If you have any questions or are having difficulty programming your HomeLinkT buttons, refer to the HomeLinkT web site at: www.homelink.com or call 1-800-355-3515.
6. Press and release the (cid:147)smart(cid:148) or (cid:147)learn(cid:148) pro- gram button located on the garage door opener(cid:146)s motor to activate the (cid:147)training mode(cid:148). This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button.
NOTE:
Once you have pressed and released the program button on the garage door open- er(cid:146)s motor and the (cid:147)training light(cid:148) is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step.
7. Within 30 seconds of pressing and releas- ing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you(cid:146)ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training.
8. Your HomeLinkT button should now be pro- grammed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-8 only.)
PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (note steps 2 - 4 under (cid:147)Pro- gramming HomeLinkT(cid:148)) while you press and re- press ((cid:147)cycle(cid:148)) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).
NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the (cid:147)cycling(cid:148) process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLinkT Universal Transceiver button. The amber indicator light will illuminate while the signal is being transmitted.
Instruments and controls 2-53
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLinkT does not quickly learn the hand- held transmitter information: c replace the hand-held transmitter batteries
with new batteries.
c position the hand-held transmitter with its from the
facing
away
battery HomeLinkT surface.
area
c press and hold both the HomeLinkT and hand-held transmitter buttons without inter- ruption.
c position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the
HomeLinkT surface. Hold the transmitter in
that position for up to 15 seconds.
If
HomeLinkT is not programmed within that
time, try holding the transmitter in another
position (cid:150) keeping the indicator light in view
at all times.
If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual.
2-54 Instruments and controls
CLEARING THE PROGRAMMED
INFORMATION
Individual buttons cannot be cleared. However,
to clear all programming, press and hold the two
outside buttons and release when the indicator
light begins to flash (approximately 20 seconds).
REPROGRAMMING A SINGLE
HOMELINKT BUTTON
To reprogram a HomeLinkT Universal Transceiver
button, complete the following.
1. Press and hold the desired HomeLinkT but-
ton. Do not release the button until step 4
has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 1 - 3 inches (26 - 76
mm) away from the HomeLinkT surface.
3. Press and hold the hand-held transmitter
button.
4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not af- fect any other programmed HomeLinkT buttons.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLinkT. Consult the
Owner(cid:146)s Manual of each device or call the manu-
facturer or dealer of those devices for additional
information.
When your vehicle is recovered, you will
need to reprogram the HomeLinkT Univer-
sal Transceiver with your new transmitter
information.
FCC Notice:
This device complies with FCC rules part
15. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference and (2) This de-
vice must accept any interference that may
be received,
including interference that
may cause undesired operation.
This transmitter has been tested and com-
plies with FCC and DOC/MDC rules.
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user(cid:146)s authority to op-
erate the equipment.
DOC: ISTC 1763K1313
FCC I.D. CV2V67690
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
3 Pre-driving checks and adjustments
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN vehicle immobilizer system keys
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4
Locking with power door lock switch
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Wide Open doors (if so equipped) . . . . . . . . . . . . . . . 3-5
Child safety rear door lock
(Crew Cab models only) . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Remote keyless entry system (if so equipped). . . . . . . . . 3-7
How to use remote keyless entry system . . . . . . . . . . 3-8
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Pedal position adjustment (if so equipped) . . . . . . . . . . 3-12
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
Rearview mirror (if so equipped). . . . . . . . . . . . . . . . . 3-15
Automatic anti-glare rearview mirror
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Automatic drive positioner (if so equipped) . . . . . . . . . . 3-21
Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-21
Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
KEYS
1.
2.
WPD0128
Two master keys (black) with transpon-
der chip (if so equipped) and chrome
NISSAN brand symbol on one side
Valet key (black) with transponder chip
(if so equipped)
Key number plate
Transponder chip (if so equipped)
3. 4. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate.
3-2 Pre-driving checks and adjustments
your NISSAN dealer for registration. This is be- cause the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.
A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS (if so equipped) You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.
The master key can be used for all the locks.
The valet key cannot be used for the console box lock, the beside storage compartment lock, or the glove box lock (if so equipped).
To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can dupli- cate your existing key. As many as five NISSAN Vehicle Immobilizer System keys can be used with one vehicle. You should bring all NISSAN Vehicle Immobilizer System keys that you have to
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
DOORS
WARNING
c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.
c Before opening any door, always look
for and avoid oncoming traffic.
c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.
Turning the key one time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks all doors s4 . Opening and closing windows The driver(cid:146)s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. c To open the windows, turn the driver(cid:146)s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. c To close the windows, turn the driver(cid:146)s door key to the front of the vehicle for longer than 1 second after the door is locked.
Windows stop when the key cylinder is released.
Driver(cid:146)s side
LPD0240
LOCKING WITH KEY Manual To lock a door, turn the key toward the front of the vehicle s1 . To unlock, turn the key toward the rear s4 . Power The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front s1 of the vehicle locks all doors.
Pre-driving checks and adjustments 3-3
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LPD0241
WPD0317
WPD0381
Door lock switch (cid:151) Type B
Inside lock
LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .
Door lock switch (cid:151) Type A
LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the lock position s1 . When locking the door this way, be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the unlock position s2 .
3-4 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
Lockout protection When the power door lock switch (driver(cid:146)s or front passenger(cid:146)s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and then unlock auto- matically. This helps to prevent the keys from being accidently locked inside the vehicle.
LPD0278
WIDE OPEN DOORS (if so equipped)
LPD0266
2. From the outside, pull the door handle s1
toward you.
CAUTION
Do not open the Wide Open door to the full open position while the fuel-filler door is open; only open it as far as the first detent. Opening the door to the full open position may damage the fuel-filler door and Wide Open door.
The Wide Open doors open nearly 180(cid:176) to allow access to the rear of the cab. 1. Open the driver(cid:146)s or passenger(cid:146)s door.
Pre-driving checks and adjustments 3-5
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LPD0267
From the inside, pull the inside door handle to-
ward you. The door will unlock automatically.
3. Open the door to the desired position.
LPD0265
3-6 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LPD0242
CHILD SAFETY REAR DOOR LOCK
(Crew Cab models only)
Child safety locks help prevent the rear doors
from being opened accidentally, especially when
small children are in the vehicle.
The child safety lock levers are located on the
edge of the rear doors.
When the lever is in the lock position, the
door can be opened only from the outside.
CAUTION
Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against
another object.
c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).
If a keyfob is lost or stolen, NISSAN rec- ommends erasing the ID code of that key- fob. This will prevent the keyfob from un- authorized use to unlock the vehicle. For information regarding the erasing proce- dure, please contact a NISSAN dealer.
REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
It is possible to lock/unlock all doors, turn on the interior lights and puddle lamps (if so equipped), and activate the panic alarm by using the keyfob from outside the vehicle.
Some settings for the keyfob, such as horn beep, can be adjusted. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For vehicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a maximum distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle. As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer. The keyfob will not function when: c the battery is discharged. c the distance between the vehicle and the
keyfob is over 33 ft (10 m).
The panic alarm will not activate when the key is in the ignition switch.
Pre-driving checks and adjustments 3-7
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
c When the
button is pushed with all doors locked, the hazard warning lights flash twice and the horn beeps once as a re- minder that the doors are already locked.
c If a door is open and you push the
button, the doors will lock but the horn will not beep and the hazard warning lights will not flash.
The horn may or may not beep. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For ve- hicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) sec- tion later in this manual.
LPD0210
button on the keyfob once.
Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The hazard warning lights flash once if all doors are completely closed with the ignition key in any position except the ON position. c The interior lights and puddle lamps (if so equipped) turn on and the light timer acti- vates for 30 seconds when the interior light switch is in the DOOR position with the ignition key in any position except the ON position.
LPD0209
HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all doors. 4. Push the
button on the keyfob. All the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked.
3-8 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
button on the keyfob again within
Push the 5 seconds. c All doors unlock. c The hazard warning lights flash once if all
doors are completely closed.
The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the off position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 1 minute unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and
the key is turned from OFF to ON.
Linking the keyfob to automatic drive positioner memory If the vehicle is equipped with automatic drive positioner, the keyfob can be linked to a memory setting. See (cid:147)Automatic drive positioner(cid:148) later in this sec- tion.
LPD0211
LPD0262
Using the panic alarm
If you are near your vehicle and feel threatened,
you may activate the panic alarm to call attention
by pushing and holding the
button on the
keyfob for longer than 0.5 second.
The panic alarm and headlights will stay on for 25
seconds.
The panic alarm stops when:
c it has run for 25 seconds, or
c any button is pushed on the keyfob.
Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob.
NOTE:
If you change the horn beep and lamp flash
feature with the keyfob, the display screen
(if so equipped) will not show the current
mode and cannot be used to change the
mode. Use the keyfob to return to the pre-
vious mode and re-enable the display
screen control.
To deactivate: Press and hold the
and
Pre-driving checks and adjustments 3-9
buttons for at least 2 seconds.
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
buttons for at least 2 seconds
The hazard warning lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. Using the interior lights Push the button on the keyfob once to turn on the interior lights and puddle lamps (if so equipped). For additional information, refer to (cid:147)Interior light(cid:148) in the (cid:147)Instruments and controls(cid:148) section earlier in this manual.
3-10 Pre-driving checks and adjustments
HOOD
s1 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly.
s2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood.
When closing the hood, lower it slowly and make sure it locks into place.
LPD0244
WARNING
c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.
c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
FUEL-FILLER DOOR
LPD0263
FUEL-FILLER CAP The fuel-filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.
For additional information, see (cid:147)Fuel recommen- dation(cid:148) and (cid:147)Flexible fuel vehicle (FFV) fuel rec- ommendation(cid:148) in the (cid:147)Technical and consumer information(cid:148) section later in this manual.
WARNING
c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.
c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
c Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator light to come on. c Never pour fuel into the throttle body to
attempt to start your vehicle.
c Do not fill a portable fuel container on a truck bed liner, rubber truck bed mad, or other insulating material. Static elec- tricity can cause an explosion of flam- mable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the
ground when filling.
(cid:150) Do not use electronic devices when
filling.
(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.
(cid:150) Use only approved portable fuel con-
tainers for flammable liquid.
CAUTION
c Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.
c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.
Pre-driving checks and adjustments 3-11
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
c Tighten until the fuel-filler cap clicks. Failure to tighten the fuel-filler cap properly may cause the mal- function indicator light (MIL) to illumi- nate. If the light illuminates be- cause the fuel-filler cap is loose or missing, tighten or install the cap and to continue vehicle. The light should turn off after a
drive
the
If the
light few driving trips. does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. c For additional
information, see the (cid:147)Malfunction indicator light (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.
3-12 Pre-driving checks and adjustments
STEERING WHEEL
PEDAL POSITION ADJUSTMENT (if so equipped)
LPD0254
TILT OPERATION Pull the lock lever forward and hold it to adjust the steering wheel up or down to the desired posi- tion. Release the lock lever to lock the steering wheel in place.
WARNING
Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.
LPD0255
The accelerator and brake pedals can be ad-
justed for driving comfort.
Use the pedal adjusting switch to adjust the
brake and accelerator pedal position forward s1
or backward s2 . Pedal adjustment can only be
performed when:
c Ignition switch is in the OFF or ACC position
c Ignition switch is ON and the selector lever
is in the P (Park) position
The brake and accelerator pedals cannot be ad- justed separately.
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
SUN VISORS
CAUTION
Do not adjust the pedal position with your foot on the pedal.
Type A
LPD0273
LPD0264
s1 To block glare from the front, swing down the
Type B
main sun visor.
s2 To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side.
s3 To block glare from the side and front, swing
down the sub-sun visor (if so equipped).
s4 Slide the extension sun visor (if so equipped)
in or out as needed.
Pre-driving checks and adjustments 3-13
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
CAUTION
c Do not store the sun visor before return- ing the extension to its original position.
c Do not pull the extension sun visor forc-
edly downward.
WPD0168
LPD0257
Type A
Type B
VANITY MIRRORS To access the vanity mirror, pull the sun visor down and flip open the mirror cover (if so equipped). Some vanity mirrors are illuminated and turn on when the mirror cover is open.
3-14 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
MIRRORS
WPD0126
REARVIEW MIRROR (if so equipped)
The night position s1 reduces glare from the
headlights of vehicles behind you at night.
Use the day position s2 when driving in daylight
hours.
WARNING
Use the night position only when neces- sary, because it reduces rear view clarity.
WPD0331
AUTOMATIC ANTI-GLARE REARVIEW MIRROR (if so equipped) The inside mirror is designed so that it automati- cally dims according to the intensity of the head- lights of the vehicle following you. The automatic anti-glare feature operates only when the ignition switch is in the ON position. The indicator light s1 will automatic anti-glare feature is operating. To turn off the anti-glare feature, push the button. The indicator light will turn off. To turn on the anti-glare feature again, push the button. The indicator light will turn on.
illuminate when the
NOTE: Do not hang any objects over the sensors s2 or apply glass cleaner to the sensors. Doing so will reduce the sensitivity of the sensors, resulting in improper operation. OUTSIDE MIRRORS
WARNING
c Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.
Pre-driving checks and adjustments 3-15
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LPD0237
WPD0170
LPD0279
Electric control type (if so equipped) The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. Move the small switch s1 to select the right or left mirror. Adjust each mirror to the desired position using the large switch s2 .
Manual control type (if so equipped) The outside mirror can be moved in any direction for a better rear view.
Trailer tow mirrors (if so equipped)
WARNING
Objects viewed in the convex portion of the trailer tow mirror are closer than they appear. Be careful when changing lanes or turning. Using only the convex mirror could cause an accident. Use the other mirrors or glance over your shoulder to properly judge distances to other objects.
3-16 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
Use the outside mirror remote control to adjust the top portion of the trailer tow mirror. The lower portion of the trailer tow mirror can be moved manually in any direction for a better rear view.
Type A
LPD0259
Manual folding outside mirrors (if so equipped) Pull the outside mirror toward the door to fold it.
LPD0268
Pull the trailer tow mirror outward to extend it to
the desired position for better visibility while tow-
ing a trailer.
WARNING
Do not extend or retract mirrors while driv- ing. You may lose control of your vehicle and cause an accident.
CAUTION
Driving in tight spaces with mirrors ex- tended may cause damage to the vehicle.
Pre-driving checks and adjustments 3-17
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
headlights of trailing vehicles. The automatic anti- glare feature operates only when the ignition switch is in the ON position. The automatic anti-glare feature will be on when starting the vehicle. The indicator light on the automatic anti-glare rearview mirror will illuminate when the automatic anti-glare feature is operat- ing. To turn off the anti-glare feature, push the button on the rearview mirror. The indicator light will turn off. To turn on the anti-glare feature again, push the button on the rearview mirror. The in- dicator light will turn on. For information on the automatic anti-glare rear- view mirror, see (cid:147)Automatic anti-glare rearview mirror(cid:148) earlier in this section. Heated mirrors (if so equipped) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. For addi- tional information, see (cid:147)Rear window and outside mirror (if so equipped) defroster switch(cid:148) in the (cid:147)Instrument and controls(cid:148) section of this manual.
Type B
LPD0269
LPD0196
Power folding outside mirrors (if so equipped)
CAUTION
Do not manually fold the power folding mirrors. Manually folding the mirrors can damage the mirrors.
Press the switch to open or close the mirrors. Automatic anti-glare outside mirrors (if so equipped) The outside mirrors will automatically dim during nighttime conditions to reduce the glare from the
3-18 Pre-driving checks and adjustments
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
For proper truck box loading see (cid:147)Vehicle loading information(cid:148) in the (cid:147)Technical and consumer in- formation(cid:148) section of this manual.
WARNING
c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.
c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
c Be sure everyone in your vehicle is in a
seat and using a seat belt properly.
TRUCK BOX
LPD0270
TAILGATE Opening the tailgate Pull the tailgate handle upward and lower the tailgate. The support cables hold the tailgate open.
When closing the tailgate, make sure the latches are securely locked. Do not drive the vehicle with the tailgate down, unless equipped with NISSAN(cid:146)s Bed Extender (accessory) or equivalent in the extended position.
Removing the tailgate 1. Release the tailgate support cables.
LPD0271
CAUTION
c The tailgate is heavy. Two people should remove or install it. Be careful not to drop it during removal.
c After releasing the support cables, do not let the tailgate rest on the bumper.
2. Hold the tailgate at a 45 degree angle. 3. Pull the tailgate out from the left side hinge. 4. Slide the tailgate out of the right side hinge.
Pre-driving checks and adjustments 3-19
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
Installing the tailgate 1. 2. Hold the tailgate at a 45 degree angle and
Insert the tailgate into the right side hinge.
insert into the left side hinge.
3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables.
4. Close the tailgate securely.
3-20 Pre-driving checks and adjustments
LPD0272
LTI0102
Locking the tailgate To unlock the tailgate, turn the key toward the passenger side of the vehicle s1 . To lock, turn the key toward the driver side s2 . Both the master key and the valet key can be used to lock and unlock the tailgate.
TIE DOWN HOOKS For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box. c The weight of the cargo load must be evenly distributed over both the front and the rear axles.
c All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle.
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
WARNING
c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
AUTOMATIC DRIVE POSITIONER (if so equipped)
The automatic drive positioner system has two features: c Memory storage function c Entry/exit function
LPD0260
MEMORY STORAGE FUNCTION Two positions for the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory sys- tem.
1. Set the automatic transmission selector le-
ver to the P (Park) position.
2. Turn the ignition ON.
Pre-driving checks and adjustments 3-21
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
3. Adjust
the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional infor- mation, see (cid:147)Seats(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint sys- tem(cid:148) section and (cid:147)Pedal position adjust- ment(cid:148) and (cid:147)Outside mirrors(cid:148) earlier in this section.
During this step, do not turn the ignition to any position other than ON.
4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second.
The indicator light for the pushed memory switch will come on and stay on for approxi- mately 5 seconds after pushing the switch. After the indicator light goes off, the se- lected positions are stored in the selected memory (1 or 2).
If a new memory is stored in the same memory switch, the previous memory will be deleted. Linking a keyfob to a stored memory position Each keyfob can be linked to a stored memory position (memory switch 1 or 2) with the follow- ing procedure. 3-22 Pre-driving checks and adjustments
1. Follow the steps for storing a memory posi-
tion.
2. While the indicator light for the memory switch being set is illuminated for 5 sec- button on the keyfob. onds, press the The indicator light will blink. After the indica- tor light goes off, the keyfob is linked to that memory setting.
With the key removed from the ignition switch, press the button on the keyfob. The driv- er(cid:146)s seat, accelerator and brake pedals, and out- side mirrors will move to the memorized position.
NOTE: If a new memory position is saved to the memory switch, the keyfob automatically re-links. Confirming memory storage c Turn the ignition ON and push the SET switch. If the main memory has not been stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indica- tor light will stay on for approximately 5 sec- onds.
c If the battery cable is disconnected, or if the fuse opens, the memory storage function will be canceled and must be restarted before a
stored memory position can be set again. Drive the vehicle over 25 MPH (40 km/h) to restart the memory storage function. You can also restart the memory storage function using the following procedure.
1. Connect the battery cable or replace the
fuse.
2. Open and close the driver(cid:146)s door more than two times with the ignition key in the LOCK position. Once the memory storage function has been restarted, you can store a memory position. See (cid:147)Memory storage function(cid:148) earlier in this section.
Selecting the memorized position Set the automatic transmission selector lever to the P (Park) position, then: c Within 45 seconds of opening the driver(cid:146)s door, push the memory switch (1 or 2) fully for at least 1 second, or
c Turn the ignition switch to the ON position and push the memory switch (1 or 2) fully for at least 1 second.
The driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors will move to the memorized position with the indicator light blinking, and then the light will stay on for approximately 5 seconds.
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
ENTRY/EXIT FUNCTION This system is designed so that the driver(cid:146)s seat will automatically move when the automatic transmission selector lever is in the P (Park) position. This allows the driver to get into and out of the driver(cid:146)s seat more easily. The driver(cid:146)s seat will slide backward: c When the key is removed from the ignition
switch and the driver(cid:146)s door is opened.
c When the driver(cid:146)s door is opened with the
ignition key turned to LOCK.
c When the ignition key is turned from ACC to
LOCK with the driver(cid:146)s door open.
The driver(cid:146)s seat will return to the previous posi- tion: c When the key is inserted into the ignition
switch and the driver(cid:146)s door is closed.
c When the driver(cid:146)s door is closed with the key
turned to LOCK.
c When the key is turned from ACC to ON while the automatic transmission selector lever is in the P (Park) position.
The entry/exit function can be adjusted or can- celed. For vehicles with navigation system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio sys-
tems(cid:148) section of this manual. For vehicles without navigation system, see your NISSAN dealer. Restarting the entry/exit function If the battery cable is disconnected or if the fuse opens, the entry/exit function will be disabled. Drive the vehicle over 25 MPH (40 km/h) to restart the entry/exit function. You can also restart the entry/exit function using the following proce- dure.
1. Connect the battery cable or replace the
fuse.
2. Open and close the driver(cid:146)s door more than two times with the ignition key in the LOCK position.
The entry/exit function should now work properly.
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
c When the vehicle speed is above 4 MPH (7
km/h).
c When any of
the memory switches are pushed while the automatic drive positioner is operating.
c When the adjusting switch for the driver(cid:146)s seat is turned on while the automatic drive positioner is operating.
c When the memory switch (1 or 2) is not
pushed and held for at least 1 second.
c When the seat has been already moved to
the memorized position.
c When no seat position is stored in the
memory switch.
c When the automatic transmission selector lever is moved from P (Park) to any other position.
c When the driver(cid:146)s door remains open more than 45 seconds and the ignition switch is not in the ON position.
The automatic drive positioner system can be adjusted and canceled. For vehicles with naviga- tion system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section of this manual. For ve- hicles without navigation system, see your NISSAN dealer.
Pre-driving checks and adjustments 3-23
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
MEMO
3-24 Pre-driving checks and adjustments
4 Display screen, heater, air conditioner and audio systems
Control panel buttons (if so equipped) . . . . . . . . . . . . . . . 4-2
How to use the joystick and ENTER button . . . . . . . . 4-3
How to use the BACK button . . . . . . . . . . . . . . . . . . . . 4-3
Setting up the start-up screen . . . . . . . . . . . . . . . . . . . 4-3
How to use the TRIP button . . . . . . . . . . . . . . . . . . . . . 4-3
How to use the SETTING button . . . . . . . . . . . . . . . . . 4-7
button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . 4-14
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Air conditioner operation . . . . . . . . . . . . . . . . . . . . . . . 4-17
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Heater and air conditioner (automatic)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Automatic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Manual operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Operating tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-24
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
Satellite radio reception (if so equipped) . . . . . . . . . 4-25
Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-26
FM/AM radio with compact disc (CD) player
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
FM/AM/SAT radio with compact disc (CD)
changer (Type A, B, C and D)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44
Steering wheel switch for audio control
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45
Rear audio controls (if so equipped) . . . . . . . . . . . . . 4-46
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47
NISSAN mobile entertainment system (MES)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47
Digital video disc (DVD) player controls . . . . . . . . . . 4-48
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49
Flip-down screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49
Playing a digital video disc (DVD) . . . . . . . . . . . . . . . 4-51
Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 4-54
How to handle the DVD . . . . . . . . . . . . . . . . . . . . . . . . 4-54
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-57
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
WARNING
c Positioning of the heating or air condi- tioning controls and display controls should not be done while driving in or- der that full attention may be given to the driving operation.
c Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock.
c Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
c In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock.
CONTROL PANEL BUTTONS (if so equipped)
1.
brightness control button (P. 4-13)
5. TRIP button (P. 4-3)
2. BACK (previous) button (P. 4-3)
3. Joystick and ENTER button (P. 4-3)
4. SETTING button (P. 4-7)
6. DEST button*
7. ROUTE button*
8. MAP button*
LHA0581
4-2 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
9. GUIDE VOICE button* 10. zoom out button* 11. zoom in button* *For Navigation system control buttons, refer to the separate Navigation System Owner(cid:146)s Manual. When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: ENTER button (cid:151) This is a button on the control panel. Display key (cid:151) This is a select key on the screen. By selecting this key you can proceed to the next function. HOW TO USE THE JOYSTICK AND ENTER BUTTON Use the joystick to choose an item on the display screen. Move the joystick up, down, left or right to highlight an item. Then press the ENTER button to select the item or perform the action.
HOW TO USE THE BACK BUTTON This button has two functions. c Go back to the previous display (cancel). If you press the BACK button during setup, the setup will be canceled and/or the display will return to the previous screen. c Finish setup. In some screens pressing the BACK button ac- cepts the changes made during setup. SETTING UP THE START-UP SCREEN When you turn the ignition key to ACC or ON, the system start-up warning is displayed on the screen. Read the warning and select the (cid:147)OK(cid:148) key by pressing the ENTER button. If you do not press the ENTER button, the Navi- gation system will not proceed to the next step in the Navigation display. If you do not touch a button or screen key for more than 1 minute on the system start-up warn- ing screen, the screen will change to the audio screen automatically. To proceed to the next step, refer to the separate Navigation System Owner(cid:146)s Manual.
LHA0572
HOW TO USE THE TRIP BUTTON
When the TRIP button is pressed, the following
modes will display on the screen.
Warning message (if any) ! TRIP 1 ! TRIP 2 !
FUEL ECONOMY ! MAINTENANCE ! Audio
or OFF ! TRIP 1
Each trip display tracks an independent trip and
displays the following:
c Elapsed Time - Journey time since the last
reset up to a maximum of 99 hours and 59
minutes.
c Driving Distance - Distance driven (mile or
km) since the last reset.
Display screen, heater, air conditioner and audio systems 4-3
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
c Average Speed - Average speed driven
(MPH or km/h) since the last reset.
Resetting trip 1 and trip 2
Each trip screen can be reset to 0. Press the TRIP
button to select the TRIP screen to be reset.
c Select the (cid:147)Reset(cid:148) key on screen by press-
ing the ENTER button, or
c Press the TRIP button for more than approxi-
mately 1.5 seconds.
Resetting fuel economy The average fuel economy calculation can be reset to 0. Press the TRIP button repeatedly until the FUEL ECONOMY menu is shown, then ei- ther: c Select the (cid:147)Reset(cid:148) key on screen by press-
ing the ENTER button, or
c Press the TRIP button for more than approxi-
mately 1.5 seconds.
Distance to empty (MI or km) The Distance To Empty (DTE) mode provides you with an estimation of the distance that can be driven before refueling. The DTE is constantly calculated based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. When the fuel level is low, the DTE display will change to (*).
NOTE: c If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may con- tinue to be displayed.
c When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display.
LHA0573
Fuel economy Press the TRIP button to display Average Fuel Economy and Distance To Empty. Average fuel economy (MPG or L/100 km)
The Average Fuel Economy is calculated based
on fuel consumption since the last reset. The
display is updated every 30 seconds and 1/3
mile (500 m). After a reset or connecting the
battery cables, the display will show (**.*).
4-4 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LHA0574
LHA0575
LHA0576
Maintenance items Press the TRIP button to display maintenance information or set maintenance intervals for the following: c Engine Oil c Tire Rotation c Tire Pressure (if so equipped) For setting the Tire Pressure display, refer to (cid:147)Tire pressure information(cid:148) later in this section.
Changing the maintenance interval Select the (cid:147)Engine Oil(cid:148) or (cid:147)Tire Rotation(cid:148) key using the joystick and press the ENTER button to display the screen to change the maintenance interval. Select the (cid:147)Maintenance Schedule(cid:148) key using the joystick and move the joystick to right or left to set the maintenance interval.
Resetting the maintenance interval The ENGINE OIL and TIRE ROTATION mainte- nance intervals can be reset to 0 miles (kilome- ters). Select the (cid:147)Reset(cid:148) key using the joystick and press the ENTER button.
Display screen, heater, air conditioner and audio systems 4-5
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
c The ignition key is turned ON the next time
the vehicle will be driven.
To return to the previous display after the MAIN- TENANCE NOTICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: c (cid:147)Reset(cid:148) key is selected. c (cid:147)Display Maintenance Notification(cid:148) is set to
OFF.
c The maintenance interval is set again.
LHA0483
Displaying the maintenance notice re-
minder
Select the (cid:147)Display Maintenance Notification(cid:148) key and press the ENTER button to display the MAINTENANCE INFORMATION automatically at the set maintenance interval.
The MAINTENANCE NOTICE screen (ENGINE OIL and TIRE ROTATION) will be automatically displayed as shown when both of the following conditions are met: c The vehicle is driven the set distance and the
ignition key is turned OFF.
LHA0577
Tire pressure information To display tire pressure information, press the TRIP button repeatedly until the MAINTENANCE screen is displayed. Select the (cid:147)Tire Pressure(cid:148) key using the joystick and press the ENTER but- ton.
Pressure indication in ** psi on the screen indi- cates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.
The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.
4-6 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
Tire pressure rises and falls depending on the heat caused by the vehicle(cid:146)s operation and the outside temperature. In case of low tire pressure, a message is dis- played on the screen: LOW PRESSURE (cid:151) Check All Tires.
WARNING
c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the Tire Pressure Monitoring System (TPMS) will not function and the low tire pressure warning light will flash. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.
LHA0558
WHA0715
HOW TO USE THE SETTING BUTTON When the SETTING button is pressed, the SET- TINGS screen will appear on the display. You can select and/or adjust several functions, features and modes that are available for your vehicle. Move the joystick and press the ENTER button to select each item to be set.
Display settings Select the (cid:147)Display(cid:148) key and press the ENTER button. The DISPLAY SETTINGS screen will ap- pear.
Display screen, heater, air conditioner and audio systems 4-7
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
To turn the screen on, c Press the SETTING button and select the (cid:147)Display(cid:148) key and then select the (cid:147)Display Off(cid:148) key. Then set the screen to on by press- ing the ENTER button, or
c Hold the
button for approximately 2
seconds and the message (cid:147)resuming dis-
play(cid:148) will appear and the (cid:147)Display Off(cid:148) key
will be automatically turned on (no amber
indicator).
WHA0716
LHA0642
Brightness/contrast: Select the (cid:147)Brightness/Contrast(cid:148) key to adjust the brightness and contrast of the map back- ground. Use the joystick to adjust the brightness to darker or brighter and the contrast to lower or higher. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.
Display off: Select the (cid:147)Display Off(cid:148) key. The indicator of the (cid:147)Display Off(cid:148) turns amber and the message above will be displayed briefly. When the audio, HVAC (Heater and air conditioner), or any mode button on the control panel is operated, the dis- play turns on for that operation. If one of the control panel buttons is pressed, the display will not automatically turn off until that operation is finished. Otherwise, the screen turns off auto- matically after 5 seconds.
4-8 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
WHA0715
Lower display setting: You can choose to display the audio or HVAC (Heater and air conditioner) functions on the lower part of the display. Select the (cid:147)Lower Dis- play Setting(cid:148) key by using the joystick. Then se- lect the (cid:147)Audio(cid:148) or (cid:147)HVAC(cid:148) key using the joystick or by pressing the ENTER button. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.
WHA0717
Any time audio information is shown on the main
part of the screen, HVAC information will be
displayed on the lower part of the screen. HVAC
information will be shown even if (cid:147)Audio(cid:148) is se-
lected to be displayed on the lower part of the
screen.
LHA0559
Vehicle electronic systems Select the (cid:147)Vehicle Electronic Systems(cid:148) key by using the joystick and pressing the ENTER but- ton. The VEHICLE ELECTRONIC SYSTEMS screen will be displayed.
You can set the following operating conditions by selecting the desired item using the joystick, then pressing the ENTER button. The indicator light, box at the left of the selected item, alternately turns on and off each time the ENTER button is pressed.
Indicator light is illuminated (cid:151) ON
Display screen, heater, air conditioner and audio systems 4-9
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
NOTE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control. Auto re-lock time: Select to set the length of time before doors automatically re-lock. Sensitivity of automatic headlights: Select to change the sensitivity setting of the automatic headlights: c Lower: less sensitive, automatic headlights will take longer to come on when the head- light sensor senses less ambient light.
LHA0564
LHA0565
Indicator light is not illuminated (cid:151) OFF Adjust driver seat when exiting vehicle: Se- lect so the driver(cid:146)s seat automatically moves back and returns to the original position for ease of exit and entry. Remote unlock driver(cid:146)s door first: Select to change which doors will unlock first during an unlocking operation: Only the driver(cid:146)s door ˆ! All the doors Keyless remote response (cid:151) horn: Select to turn on or turn off the horn chirp mode used when the LOCK button on the keyfob is pressed.
NOTE:
If you change the horn beep or the lamp flash feature with the keyfob, the display screen will not show the current mode. Use the keyfob to return to the previous mode and re-enable the display screen control.
Keyless remote response (cid:151) lights: Select to turn on or turn off the hazard indicator flash mode used when the LOCK or UNLOCK button on the keyfob is pressed.
4-10 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
c Higher: more sensitive, automatic headlights will come on quicker when the headlight sensor senses less ambient light.
Automatic headlights off delay: Select to change the setting for the length of time the automatic headlights remain on after exiting the vehicle. Speed dependent wiper: Select to turn on or turn off the driving speed dependent intermittent wiper function. Return all settings to default: Select to change all VEHICLE ELECTRONICS SYSTEMS to their default settings.
You can select the language and unit using the joystick or pressing the ENTER button. The settings are automatically saved when you exit the menu by pressing the BACK button or any other mode button.
LHA0561
System settings Select the (cid:147)System Settings(cid:148) key by using the joystick and pressing the ENTER button. The SYSTEM SETTINGS screen will be displayed. Language/unit
The LANGUAGE/UNIT screen will appear when selecting the (cid:147)Language/Unit(cid:148) key and pressing the ENTER button.
Language: English or French
Unit: US (cid:151) mile, (cid:176)F, MPG
Metric (cid:151) km, (cid:176)C, L/100 km
Display screen, heater, air conditioner and audio systems 4-11
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
LHA0562
LHA0566
LHA0567
Clock Adjusting the time: Select the (cid:147)Hours(cid:148) or (cid:147)Minutes(cid:148) key and move the joystick to the right or left to adjust the time. The time will change step by step. The new settings are automatically saved when you exit the setting screen by pressing the BACK button or any other mode button.
Setting daylight savings time: Use the (cid:147)Daylight Saving Time(cid:148) key to adjust the clock to daylight savings time. ON: The displayed time advances by 1 hour. OFF: The current time is displayed.
Adjusting the time to the GPS: Select the (cid:147)Auto Adjust(cid:148) key. The time will be reset to the GPS time.
4-12 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
The GPS time (manual time) corresponding to the selected zone will be displayed. Pacific zone has been set as the initial (default) setting. Beep setting With this option ON, a beep will sound if any audio button is pressed. Navigation settings Refer to the separate Navigation System Own- er(cid:146)s Manual for information regarding these set- tings. Guidance voice settings Refer to the separate Navigation System Own- er(cid:146)s Manual for information regarding these set- tings.
BUTTON
To change the display brightness, press the button. Pressing the button again will change the display to (cid:147)DAY(cid:148) or (cid:147)NIGHT(cid:148) display. Then, adjust the brightness by moving the joy- stick right or left. If no operation is done within 10 seconds, or if the BACK button is pressed, the display will return to the previous display.
Selecting the time zone: 1. Select the (cid:147)Select Time Zone(cid:148) key. The TIME ZONE screen will appear.
LHA0568
LHA0563
2. Select one of the following zones, depend-
ing on the current location. c Pacific zone c Mountain zone c Central zone c Eastern zone c Atlantic zone c Newfoundland zone
After selection, the CLOCK SETTINGS screen will appear.
Display screen, heater, air conditioner and audio systems 4-13
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
VENTILATORS
Adjust air flow direction for the driver and pas- senger side s1 , center s2 , and rear passenger (if so equipped) s3 ventilators by moving the venti- lator slide and/or ventilator assemblies.
HEATER AND AIR CONDITIONER (manual)
WARNING
c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.
LHA0410
4-14 Display screen, heater, air conditioner and audio systems
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
(cid:151) Air flows from defroster outlets
and the front and rear floor outlets.
(cid:151) Air flows mainly from defroster
outlets.
The air flow control dial also has intermediate positions which allow the air flow to be distrib- uted between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left. To increase the temperature, turn the dial to the right.
Air recirculation button
ON position: Push the the vehicle.
button to recirculate air inside
button to the on position when:
Push the c driving on a dusty road. c to prevent traffic fumes from entering pas-
senger compartment.
c for maximum cooling when using the air con-
ditioner.
1. 2. 3. 4. 5. 6.
Fan speed control dial Air recirculation button Temperature control dial Air conditioner button Air flow control dial Rear window defroster switch (if so equipped) CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.
WHA0535
Air flow control dial The air flow control dial allows you to select the air flow outlets. MAX A/C
(cid:151) Air flows from center and side
vents with maximum cooling (air conditioning).
(cid:151) Air flows from center and side
ventilators.
(cid:151) Air flows from center and side
ventilators and the front and rear floor outlets.
(cid:151) Air flows mainly from the front
and rear floor outlets.
Display screen, heater, air conditioner and audio systems 4-15
Z REVIEW COPY—2007 Titan (tzw) Owners Manual—USA_English (nna) 07/09/06—tbrooks X
OFF position: Push the button again to turn air recircula- tion off. Outside air is drawn into the passenger compartment and distributed through the se- lected outlet. Use the off position for normal heater or air con- ditioner operation.
Air conditioner button
HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets.
1. Push the
button to the OFF position for normal heating. The indicator light on the will ap- pear on the display, if so equipped.)
button will go off. (
2. Turn the air flow control dial to the
3. Turn the fan control dial to the desired posi-
tion.
position.
Start the engine, turn the fan control dial to the desired position and push the button to turn on the air conditioner. A/C will appear on the display when the air conditioner is operating. To turn off the air conditioner, push the button again, the display will show A/C OFF. The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch (if so equipped) For more information about the rear window de- froster switch, see (cid:147)Rear window defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. Heated mirror switch (if so equipped) For more information about the heated mirror switch, see (cid:147)Heated mirror switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section of this manual. 4-16 Display screen, heater, air conditioner and audio systems
1. Push the
position.
4. Turn the temperature control dial to the de- sired position between the middle and the hot position.
Ventilation This mode directs outside air to the side and center ventilators.
button to the OFF position. button will will appear on the display, if so
The indicator light on the go off. ( equipped.)
2. Turn the air flow control dial to the
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de-
sired position.
Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air flow control dial to the
position.
2. Turn the fan control dial to the desired posi-
tion.
3. Turn the temperature control dial to the de- sired position between the middle and the hot position.
c To quickly remove ice or fog from the win- dows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. c When the
position is selected, the air conditioner automatically turns on (however, the indicator light on the