2005 Nissan Titan Owners Manual

3-6 Pre-driving checks and adjustments

LPD0265

LPD0242
CHILD SAFETY REAR DOOR LOCK (Crew Cab models only) Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

CAUTION

Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against

another object.

c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).

If a keyfob is lost or stolen, NISSAN rec- ommends erasing the ID code of that key- fob. This will prevent the keyfob from un- authorized use to unlock the vehicle. For information regarding the erasing proce- dure, please contact a NISSAN dealer.

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)

It is possible to lock/unlock all doors, turn on the interior lights and puddle lamps (if so equipped), and activate the panic alarm by using the keyfob from outside the vehicle.

Some settings for the keyfob, such as horn beep, can be adjusted. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For vehicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a maximum distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle. As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer. The keyfob will not function when: c the battery is discharged. c the distance between the vehicle and the

keyfob is over 33 ft (10 m).

The panic alarm will not activate when the key is in the ignition switch.

LPD0209

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all doors. 4. Push the

button on the keyfob. All the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked.

Pre-driving checks and adjustments 3-7

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

c When the

button is pushed with all doors locked, the hazard warning lights flash twice and the horn beeps once as a re- minder that the doors are already locked.

c If a door is open and you push the

button, the doors will lock but the horn will not beep and the hazard warning lights will not flash.

The horn may or may not beep. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For ve- hicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) sec- tion later in this manual.

3-8 Pre-driving checks and adjustments

button on the keyfob again within

Push the 5 seconds. c All doors unlock. c The hazard warning lights flash once if all

doors are completely closed.

The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the off position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 1 minute unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and

the key is turned from OFF to ON.

Linking the keyfob to automatic drive positioner memory If the vehicle is equipped with automatic drive positioner, the keyfob can be linked to a memory setting. See (cid:147)Automatic driver positioner(cid:148) later in this section.

LPD0210

button on the keyfob once.

Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The hazard warning lights flash once if all doors are completely closed with the ignition key in any position except the ON position. c The interior lights and puddle lamps (if so equipped) turn on and the light timer acti- vates for 30 seconds when the interior light switch is in the DOOR position with the ignition key in any position except the ON position.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

buttons for at least 2 seconds.

buttons for at least 2 seconds

To deactivate: Press and hold the and The hazard warning lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. Using the interior lights Push the button on the keyfob once to turn on the interior lights and puddle lamps (if so equipped). For additional information, refer to (cid:147)Interior light(cid:148) in the (cid:147)Instruments and controls(cid:148) section earlier in this manual.

LPD0211

LPD0262

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for 25
seconds. The panic alarm stops when: c it has run for 25 seconds, or c any button is pushed on the keyfob.

Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob.

NOTE: If you change the horn beep and lamp flash feature with the keyfob, the display screen (if so equipped) will not show the current mode and cannot be used to change the mode. Use the keyfob to return to the pre- vious mode and re-enable the display screen control.

Pre-driving checks and adjustments 3-9

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

HOOD

FUEL FILLER LID

LPD0244

LPD0263

s1 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly.

s2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood.

When closing the hood, lower it slowly and make sure it locks into place.

WARNING

c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.

c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

FUEL FILLER CAP The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.

For additional information, see (cid:147)Fuel recommen- dation(cid:148) and (cid:147)Flexible fuel vehicle (FFV) fuel rec- ommendation(cid:148) in the (cid:147)Technical and consumer information(cid:148) section later in this manual.

3-10 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

WARNING

c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.

c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to

attempt to start your vehicle.

c Do not fill a portable fuel container on a truck bed liner, rubber truck bed mad, or other insulating material. Static elec- tricity can cause an explosion of flam- mable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the

ground when filling.

(cid:150) Do not use electronic devices when

filling.

(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.

(cid:150) Use only approved portable fuel con-

tainers for flammable liquid.

CAUTION

c Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.

c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap mal- properly may cause the function indicator lamp (MIL) to illumi- nate. If the lamp illuminates be- cause the fuel filler cap is loose or missing, tighten or install the cap and to continue vehicle. The lamp should turn off after a

drive

the

lamp few driving trips. If the does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. c For additional

information, see the (cid:147)Malfunction indicator lamp (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.

Pre-driving checks and adjustments 3-11

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

STEERING WHEEL

PEDAL POSITION ADJUSTMENT (if so equipped)

CAUTION

Do not adjust the pedal position with your foot on the pedal.

LPD0254

TILT OPERATION (if so equipped) Pull the lock lever forward and hold it to adjust the steering wheel up or down to the desired posi- tion. Release the lock lever to lock the steering wheel in place.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

LPD0255
The accelerator and brake pedals can be ad- justed for driving comfort.

Use the pedal adjusting switch to adjust the brake and accelerator pedal position forward s1
or backward s2 . Pedal adjustment can only be performed when: c Ignition switch is in the OFF or ACC position c Ignition switch is ON and the selector lever

is in the P (Park) position

The brake and accelerator pedals cannot be ad- justed separately.

3-12 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

SUN VISORS

CAUTION

c Do not store the sun visor before return- ing the extension to its original position.

c Do not pull the extension sun visor forc-

edly downward.

LPD0264

s1 To block glare from the front, swing down the

Type B

main sun visor.

s2 To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side.

s3 To block glare from the side and front, swing

down the sub-sun visor (if so equipped).

s4 Slide the extension sun visor (if so equipped)

in or out as needed.

Type A

LPD0273

Pre-driving checks and adjustments 3-13

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

MIRRORS

WPD0168

LPD0257

WPD0126

Type A

VANITY MIRRORS To access the vanity mirror, pull the sun visor down and flip open the mirror cover (if so equipped). Some vanity mirrors are illuminated and turn on when the mirror cover is open.

Type B

INSIDE MIRROR (if so equipped) The night position s1 reduces glare from the headlights of vehicles behind you at night. Use the day position s2 when driving in daylight hours.

WARNING

Use the night position only when neces- sary, because it reduces rear view clarity.

3-14 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LPD0280

AUTO position

AUTO indicator light Sensor (on back of mirror) Sensor

1. 2. OFF position 3. 4. 5. AUTOMATIC ANTI-GLARE INSIDE MIRROR (if so equipped) The inside mirror is designed so that it automati- cally changes reflection according to the intensity of the headlights of the vehicle following you.

When the inside mirror switch is in the AUTO position, excessive glare from the headlights of the vehicle behind you will be reduced. The

AUTO indicator light will be on. When the switch on the inside mirror is in the OFF position, the inside mirror will operate normally. Do not hang any object on the sensor or apply glass cleaner. Doing so will reduce the sensitivity of the sensor, resulting in improper operation. OUTSIDE MIRRORS

WARNING

c Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.

c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.

LPD0237

Electric control type (if so equipped) The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. Move the small switch s1 to select the right or left mirror. Adjust each mirror to the desired position using the large switch s2 .

Pre-driving checks and adjustments 3-15

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Use the outside mirror remote control to adjust the top portion of the trailer tow mirror. The lower portion of the trailer tow mirror can be moved manually in any direction for a better rear view.

WPD0170

LPD0279

Manual control type The outside mirror can be moved in any direction for a better rear view.

Trailer tow mirrors (if so equipped)

WARNING

c Objects viewed in the convex portion of the trailer tow mirror are closer than they appear. Be careful when changing lanes or turning. Using only the convex mirror could cause an accident. Use the other mirrors or glance over your shoul- der to properly judge distances to other objects.

c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.

3-16 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Heated mirrors (if so equipped) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. For addi- tional information, see (cid:147)Rear window and outside mirror (if so equipped) defroster switch(cid:148) in the (cid:147)Instrument and controls(cid:148) section of this manual.

LPD0268
Pull the trailer tow mirror outward to extend it to the desired position for better visibility while tow- ing a trailer.

WARNING

Do not extend or retract mirrors while driv- ing. You may lose control of your vehicle and cause an accident.

CAUTION

Driving in tight spaces with mirrors ex- tended may cause damage to the vehicle.

Type A

LPD0259

Foldable outside mirrors Pull the outside mirror toward the door to fold it.

Pre-driving checks and adjustments 3-17

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

TRUCK BOX

Type B

LPD0269

LPD0270

TAILGATE Opening the tailgate Pull the tailgate handle upward and lower the tailgate. The support cables hold the tailgate open.

When closing the tailgate, make sure the latches are securely locked. Do not drive the vehicle with the tailgate down, unless equipped with NISSAN(cid:146)s Bed Extender (accessory) or equivalent in the extended position.

3-18 Pre-driving checks and adjustments

For proper truck box loading see (cid:147)Vehicle loading information(cid:148) in the (cid:147)Technical and consumer in- formation(cid:148) section of this manual.

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

4. Slide the tailgate out of the right side hinge. Installing the tailgate 1. 2. Hold the tailgate at a 45 degree angle and

Insert the tailgate into the right side hinge.

insert into the left side hinge.

3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables.

4. Close the tailgate securely.

LPD0272

Locking the tailgate To unlock the tailgate, turn the key toward the passenger side of the vehicle s1 . To lock, turn the key toward the driver side s2 .

LPD0271

Removing the tailgate 1. Release the tailgate support cables.

CAUTION

c The tailgate is heavy. Two people should remove or install it. Be careful not to drop it during removal.

c After releasing the support cables, do not let the tailgate rest on the bumper.

2. Hold the tailgate at a 45 degree angle.

3. Pull the tailgate out from the left side hinge.

Pre-driving checks and adjustments 3-19

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

AUTOMATIC DRIVE POSITIONER (if so equipped)

The automatic drive positioner system has two features: c Memory storage function c Entry/exit function

LTI0102

TIE DOWN HOOKS For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box. c The weight of the cargo load must be evenly distributed over both the front and the rear axles.

c All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle.

3-20 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LPD0260

MEMORY STORAGE FUNCTION Two positions for the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory sys- tem.

1. Set the automatic transmission selector le-

ver to the P (Park) position.

2. Turn the ignition ON.

3. Adjust

the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional infor- mation, see (cid:147)Seats(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint sys- tem(cid:148) section and (cid:147)Pedal position adjust- ment(cid:148) and (cid:147)Outside mirrors(cid:148) earlier in this section.

During this step, do not turn the ignition to any position other than ON.

4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second.

The indicator light for the pushed memory switch will come on and stay on for approxi- mately 5 seconds after pushing the switch. After the indicator light goes off, the se- lected positions are stored in the selected memory (1 or 2).

If a new memory is stored in the same memory switch, the previous memory will be deleted. Linking a keyfob to a stored memory position Each keyfob can be linked to a stored memory position (memory switch 1 or 2) with the follow- ing procedure.

1. Follow the steps for storing a memory posi-

tion.

2. While the indicator light for the memory switch being set is illuminated for 5 sec- button on the keyfob. onds, press the The indicator light will blink. After the indica- tor light goes off, the keyfob is linked to that memory setting.

With the key removed from the ignition switch, press the button on the keyfob. The driv- er(cid:146)s seat, accelerator and brake pedals, and out- side mirrors will move to the memorized position.

NOTE: If a new memory is saved to the memory switch, the keyfob must be re-linked. Confirming memory storage c Turn the ignition ON and push the SET If the main memory has not been switch. stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indica- tor light will stay on for approximately 5 sec- onds.

c If the battery cable is disconnected, or if the fuse opens, the memory will be canceled. In such a case, reset the desired positions using the following procedures.

Pre-driving checks and adjustments 3-21

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

1. Open and close the driver(cid:146)s door more than two times with the ignition key in the LOCK position.

2. Reset the desired position using the previ-

ous procedure.

Selecting the memorized position 1. Set the automatic transmission selector le-

ver to the P (Park) position.

2. Turn the ignition ON.

3. Push the memory switch (1 or 2) fully for at

least 1 second.

The driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors will move to the memorized position with the indicator light blinking, and then the light will stay on for approximately 5 seconds. ENTRY/EXIT FUNCTION This system is designed so that the driver(cid:146)s seat will automatically move when the automatic transmission selector lever is in the P (Park) position. This allows the driver to get into and out of the driver(cid:146)s seat more easily. The driver(cid:146)s seat will slide backward: c When the driver(cid:146)s door is opened with the

ignition key turned to LOCK.

3-22 Pre-driving checks and adjustments

c When the ignition key is turned from ACC to LOCK with the driver(cid:146)s door open while the automatic transmission selector lever is in the P (Park) position.

The driver(cid:146)s seat will return to the previous posi- tion: c When the key is inserted into the ignition

switch.

c When the driver(cid:146)s door is closed with the key

turned to LOCK.

c When the key is turned from ACC to ON while the automatic transmission selector lever is in the P (Park) position.

The entry/exit function can be adjusted or can- celed. For vehicles with navigation system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio sys- tems(cid:148) section of this manual. For vehicles without navigation system, see your NISSAN dealer. SYSTEM OPERATION The automatic drive positioner system will not work or will stop operating under the following conditions: c When the vehicle speed is above 4 MPH (7

km/h).

c When any two or more of

the memory switches are simultaneously pushed while the automatic drive positioner is operating. c When the adjusting switch for the driver(cid:146)s seat is turned on while the automatic drive positioner is operating.

c When the memory switch (1 or 2) is not

pushed for at least 1 second.

c When the seat has been already moved to

the memorized position.

c When no seat position is stored in the

memory switch.

The automatic drive positioner system can be adjusted and canceled. For vehicles with naviga- tion system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section of this manual. For ve- hicles without navigation system, see your NISSAN dealer.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

4 Display screen, heater, air conditioner and audio systems

Control panel buttons (if so equipped) . . . . . . . . . . . . . . . 4-2
Names of the components. . . . . . . . . . . . . . . . . . . . . . . 4-3
How to use joystick and (cid:147)ENTER(cid:148) button . . . . . . . . . . 4-3
How to use (cid:147)PREV(cid:148) button . . . . . . . . . . . . . . . . . . . . . . 4-3
Setting up the start-up screen . . . . . . . . . . . . . . . . . . . 4-3
How to use the (cid:147)TRIP(cid:148) button . . . . . . . . . . . . . . . . . . . . 4-4
How to use the (cid:147)SETTING(cid:148) button. . . . . . . . . . . . . . . . 4-7
Setting the display (Audio or HVAC display): . . . . . . 4-7
button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . 4-13
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Air conditioner operation . . . . . . . . . . . . . . . . . . . . . . . 4-16
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Satellite radio reception (if so equipped) . . . . . . . . . 4-20
Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-21
FM-AM radio with compact disc (CD) player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
FM-AM-SAT radio with compact disc (CD) changer (Type A, B, C and D) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
Rear audio controls (if so equipped) . . . . . . . . . . . . . 4-38
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

NISSAN mobile entertainment system (MES) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
Digital video disc (DVD) player controls . . . . . . . . . . 4-40
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
Flip-down screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
Playing a digital video disc (DVD) . . . . . . . . . . . . . . . 4-42
Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 4-45
How to handle the DVD . . . . . . . . . . . . . . . . . . . . . . . . 4-46
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-48

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/28/05—tbrooks X

WARNING

c Positioning of the heating or air condi- tioning controls and display controls should not be done while driving in or- der that full attention may be given to the driving operation.

c Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock.

c Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.

c In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock.

CONTROL PANEL BUTTONS (if so equipped)

When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start.

LHA0388

Reference symbols: (cid:147)ENTER(cid:148) button (cid:151) This is a button on the con- trol panel.

4-2 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

If you do not touch the button or screen key for more than 1 minute on the TRIP, SETTING or START-UP screen, the screen will change to TRIP screen automatically. To proceed to the next step, refer to the separate Navigation System Owner(cid:146)s Manual.

brightness control button (P. 4-12)

(cid:147)Display(cid:148) key (cid:151) This is a select key on the screen. By selecting this key you can proceed to the next function. NAMES OF THE COMPONENTS 1. 2. PREV (previous) button (P. 4-3) 3. Joystick and ENTER push button (P. 4-3) 4. SETTING button (P. 4-7) 5. TRIP drive computer button (P. 4-4) 6. DEST button* 7. ROUTE button* 8. MAP button* 9. GUIDE VOICE button* 10. zoom out button* 11. zoom in button* *For Navigation system control buttons, refer to the separate Navigation System Owner(cid:146)s Manual.

HOW TO USE JOYSTICK AND (cid:147)ENTER(cid:148) BUTTON Choose an item on the display using the joystick and push the (cid:147)ENTER(cid:148) button for operation. HOW TO USE (cid:147)PREV(cid:148) BUTTON This button has two functions. c Go back to the previous display (cancel). If you touch (cid:147)PREV(cid:148) button during setup, the setup will be canceled and/or the display will return to the previous screen. c Finish setup. If you touch this button after the setup is com- pleted, the setup will start over, and the display will return to the climate control or audio mode and Navigation screen. SETTING UP THE START-UP SCREEN When you turn the ignition key to ACC or ON, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the (cid:147)I AGREE(cid:148) (English) or (cid:147)ENTER(cid:148) (Fran(cid:231)ais) key then push the (cid:147)ENTER(cid:148) button. If you do not push the (cid:147)ENTER(cid:148) button, the Navigation system will not proceed to the next step display.

Display screen, heater, air conditioner and audio systems 4-3

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/28/05—tbrooks X

LHA0398
HOW TO USE THE (cid:147)TRIP(cid:148) BUTTON When the (cid:147)TRIP(cid:148) button is pushed, the following modes will display on the screen. Warning message (if there are any) ! TRIP 1
(Elapsed Time, Driving Distance, Average Speed) ! TRIP 2 ! FUEL ECONOMY (Average Fuel Economy, Distance to Empty) ! MAINTE- NANCE (Engine Oil, Tire Rotation and Tire Pres- sure (cid:151) if so equipped) ! OFF.

LHA0399

LHA0402

Trip 1, trip 2 and fuel economy items To reset the TRIP 1, TRIP 2 and FUEL ECONOMY, select the (cid:147)RESET(cid:148) key using the joystick and push the (cid:147)ENTER(cid:148) button or push the (cid:147)TRIP(cid:148) button for more than approximately 1.5 seconds.

Maintenance items You can set the engine oil and the tire rotation interval. To display the setting of the maintenance interval, select the (cid:147)Engine Oil(cid:148) or (cid:147)Tire Rotation(cid:148) key using the joystick and push the (cid:147)ENTER(cid:148) button.

4-4 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

the maintenance interval, select

LHA0400
the To set (cid:147)Maintenance Schedule(cid:148) key by using the joy- stick and push the joystick to right or left. To reset the maintenance interval, select the (cid:147)Re- set(cid:148) key using the joystick and push the (cid:147)EN- TER(cid:148) button. To display the MAINTENANCE INFORMATION automatically when set trip distance is reached, select the (cid:147)Display Maintenance Notifica- tion(cid:148) key and push the (cid:147)ENTER(cid:148) button.

LHA0401

LHA0483
The (cid:147)MAINTENANCE NOTICE(cid:148) screen ((cid:147)EN- GINE OIL(cid:148) and (cid:147)TIRE ROTATION(cid:148)) will be auto- matically displayed as shown when both of the following conditions are met: c the vehicle is driven the set distance and the

ignition key is turned OFF.

c the ignition key is turned ON the next time

the vehicle will be driving.

To return to the previous display after the (cid:147)MAIN- TENANCE NOTICE(cid:148) screen is displayed, press the PREV button.

Display screen, heater, air conditioner and audio systems 4-5

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Tire pressure rises and falls depending on the heat caused by the vehicle(cid:146)s operation and the outside temperature. In case of low tire pressure, a message is dis- played on the screen: FLAT TIRE (cid:151) low tire air pressure.

WARNING

When a spare tire is mounted or a wheel is replaced, tire pressure will not be indi- cated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

The (cid:147)MAINTENANCE NOTICE(cid:148) screen displays each time the key is turned ON until one of the following conditions are met: c (cid:147)RESET(cid:148) is selected. c (cid:147)Display Maintenance and Notification(cid:148) is

set OFF.

c the maintenance interval is set again.

LHA0403

Tire pressure information To view (cid:147)TIRE PRESSURE(cid:148) information, push the (cid:147)TRIP(cid:148) button repeatedly until the (cid:147)MAINTE- NANCE(cid:148) screen is displayed. Select (cid:147)TIRE PRESSURE(cid:148) using the joystick and push the (cid:147)ENTER(cid:148) button.

Pressure indication in ** psi on the screen indi- cates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.

4-6 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0268

HOW TO USE THE (cid:147)SETTING(cid:148) BUTTON To adjust the various settings within the display screen press the(cid:147)SETTING(cid:148) button. After pressing the SETTING button a menu will be shown on the display screen which will allow you to program several functions such as the display screen appearance, programmable fea- tures for your vehicles electronics system and other system settings such as your clock. To make a selection from this mode use the joystick and press the (cid:147)ENTER(cid:148) button.

SETTING THE DISPLAY (Audio or HVAC display): The audio or HVAC reading can be displayed at the bottom of the screen. Choose the (cid:147)Audio(cid:148) or (cid:147)HVAC(cid:148) (Heater and air conditioner) key to be displayed at the bottom, by using the joystick and pressing the ENTER button to select or deselect the key. The setting condition will normally appear on the screen. To return to the setting screen, push the (cid:147)SETTING(cid:148) button or (cid:147)PREV(cid:148) button. Display settings The DISPLAY SETTINGS screen will appear af- ter pushing the (cid:147)SETTING(cid:148) button, selecting (cid:147)Display(cid:148) key and pushing the (cid:147)ENTER(cid:148) but- ton. Brightness/Contrast/Map Background: To adjust the brightness and contrast of the screen, select the (cid:147)Brightness/contrast(cid:148) key and push the (cid:147)ENTER(cid:148) button. You can then use the joystick to adjust the brightness to Darker or Brighter and the contrast to Lower or Higher. For information on Map Background, please refer to the separate Navigation System Owner(cid:146)s Manual.

Display Off: To turn off the screen, push the (cid:147)SETTING(cid:148) button and select the (cid:147)Display(cid:148) key and (cid:147)Dis- play Off(cid:148) key. The indicator of the (cid:147)Display Off(cid:148) will turn to amber. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5 seconds after the operation is finished on the map display in the Audio, HVAC (Heater and air conditioner), SETTING or VE- HICLE INFO modes. To turn on the screen, push the (cid:147)SETTING(cid:148) button and select the (cid:147)Display(cid:148) key and (cid:147)Dis- play Off(cid:148) key, then set the screen to on by pushing the (cid:147)ENTER(cid:148) button. Setting Audio or HVAC display: Choose the (cid:147)Audio(cid:148) or (cid:147)HVAC(cid:148) (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC setting condition will normally appear on the screen. To return to the setting screen, push the (cid:147)SET- TING(cid:148) button or (cid:147)PREV(cid:148) button.

Display screen, heater, air conditioner and audio systems 4-7

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0382

LHA0381

LHA0261

Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the (cid:147)Vehicle Elec- tronic Systems(cid:148) key with the joystick and push- ing the (cid:147)ENTER(cid:148) button. To set the various electronic systems operating conditions, select the applicable item using the joystick, and push the (cid:147)ENTER(cid:148) button. The indicator light, box at left of selected item, alter- nately turns on and off each time the (cid:147)ENTER(cid:148) button is pressed. Indicator light is illuminated (cid:151) ON Indicator light is not illuminated (cid:151) OFF

4-8 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Speed dependent wiper: This key allows you to turn on or turn off the driving speed dependent intermittent wiper func- tion. Return all settings to default: When this key is selected and turned on using the (cid:147)ENTER(cid:148) button, all settings made by VE- HICLE ELECTRONICS will return to the default settings.

Adjust driver seat when exiting vehicle:

NOTE:

With this option ON, the driver(cid:146)s seat automati- cally moves back and returns to the original po- sition for ease of exit and entry. Remote unlock driver(cid:146)s door first:

This option allows you to select which doors will unlock first during an unlocking operation: Only the driver(cid:146)s door ˆ! All the doors Keyless remote response (cid:151) horn:

This key allows you to change the horn chirp mode that occurs when pressing the LOCK or UNLOCK button on the keyfob.

NOTE:

If you change the horn beep or the lamp flash feature with the keyfob, the display screen will not show the current mode. Use the keyfob to return to the previous mode and re-enable the display screen control.

Keyless remote response (cid:151) lights:

This key allows you to change the hazard indica- tor flash mode that occurs when pressing the LOCK or UNLOCK button on the keyfob.

If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Auto re-lock time:

This key allows you to set the length of time before doors auto re-lock. Sensitivity of automatic headlights:

This key allows you to set the sensitivity of the automatic headlights: c Lower- less sensitive, automatic headlights will take longer to come on when the head- light sensor senses less ambient light.

c Higher- more sensitive, automatic head- lights will come on quicker when the head- light sensor senses less ambient light.

Automatic headlights off delay:

This key allows you to set the length of time before the automatic headlights turn off after exiting the vehicle.

Display screen, heater, air conditioner and audio systems 4-9

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0262

LHA0270

LHA0271

System settings Language/Unit The LANGUAGE/UNIT screen will appear when selecting the (cid:147)Language/Unit(cid:148) key and push- ing the (cid:147)ENTER(cid:148) button. Language: English or French Unit: US (cid:151) mile, (cid:176)F, MPG

Metric (cid:151) km, (cid:176)C, L/100 km

You can select the language and unit using the joystick and (cid:147)ENTER(cid:148) button.

Clock Adjusting the time: Select the (cid:147)Hours(cid:148) or (cid:147)Minutes(cid:148) key and move the joystick to the right or left to adjust the time. The time will change step by step. After completion of (cid:147)PREV(cid:148) button.

the setting, press the

Setting daylight savings time: Use the (cid:147)Daylight Saving Time(cid:148) key to adjust the clock to daylight savings time. ON: The displayed time advances by 1 hour. OFF: The current time is displayed.

4-10 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0272

LHA0273

Adjusting the time to the GPS: Select the (cid:147)Auto Adjust(cid:148) key. The time will be reset to the GPS time.

Selecting the time zone: 1. Select the (cid:147)Select Time Zone(cid:148) key. The [TIME ZONE] screen will appear.

LHA0274
2. Select one of the following zones depending

on the current location. c Pacific zone c Mountain zone c Central zone c Eastern zone c Atlantic zone c Newfoundland zone

After selection, the [CLOCK SETTINGS] screen will appear.

Display screen, heater, air conditioner and audio systems 4-11

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

VENTILATORS

The GPS time (manual time) corresponding to the selected zone will be displayed. Pacific zone has been set as the initial (default) setting. Beep setting With this option ON, a beep will sound if any audio button is pushed.

BUTTON

To change the display brightness, push the button. Pushing the button again will change the display to DAY or NIGHT display. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the (cid:147)PREV(cid:148) button is pushed, the display will return to the previous display.

Adjust air flow direction for the driver and pas- senger side s1 , center s2 , and rear passenger (if so equipped) s3 ventilators by moving the venti- lator slide and/or ventilator assemblies.

LHA0410

4-12 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

HEATER AND AIR CONDITIONER (manual)

WARNING

c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

c Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation.

1. 2. 3. 4. 5. 6.

Fan speed control dial Air recirculation button Temperature control dial Air conditioner button Air flow control dial Rear window defroster switch (if so equipped) CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.

WHA0535

Air flow control dial The air flow control dial allows you to select the air flow outlets. MAX A/C

(cid:151) Air flows from center and side

vents with maximum cooling (air conditioning).

(cid:151) Air flows from center and side

ventilators.

(cid:151) Air flows from center and side

ventilators and the front and rear floor outlets.

(cid:151) Air flows mainly from the front

and rear floor outlets.

Display screen, heater, air conditioner and audio systems 4-13

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

(cid:151) Air flows from defroster outlets

and the front and rear floor outlets.

(cid:151) Air flows mainly from defroster

outlets.

The air flow control dial also has intermediate positions which allow the air flow to be distrib- uted between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left. To increase the temperature, turn the dial to the right.

Air recirculation button

ON position: Push the the vehicle.

button to recirculate air inside

button to the on position when:

Push the c driving on a dusty road. c to prevent traffic fumes from entering pas-

senger compartment.

c for maximum cooling when using the air con-

ditioner.

OFF position: button again to turn air recircula- Push the tion off. Outside air is drawn into the passenger compartment and distributed through the se- lected outlet. Use the off position for normal heater or air con- ditioner operation.

Air conditioner button

Start the engine, turn the fan control dial to the desired position and push the button to turn on the air conditioner. A/C will appear on the display when the air conditioner is operating. To turn off the air conditioner, push the button again, the display will show A/C OFF. The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch (if so equipped) For more information about the rear window de- froster switch, see (cid:147)Rear window defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. Heated mirror switch (if so equipped) For more information about the heated mirror switch, see (cid:147)Heated mirror switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section of this manual.

4-14 Display screen, heater, air conditioner and audio systems

HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets.

1. Push the

button to the OFF position for normal heating. The indicator light on the will ap- pear on the display, if so equipped.)

button will go off. (

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Ventilation This mode directs outside air to the side and center ventilators.

1. Push the

button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

c To quickly remove ice or fog from the win- dows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. c When the

position is selected, the air conditioner automatically turns on (however, the indicator light on the button will not come on and A/C will not appear on the display, if so equipped) if the outside tem- perature is more than 36(cid:176)F (2(cid:176)C). If in de- frost mode for more than one minute, the air conditioning system will continue to operate until the fan control dial is turned to OFF or

the vehicle is shut off, even if the air flow control dial is turned to a position other than position. This dehumidifies the air the which the windshield. The mode automatically turns off, al- lowing outside air to be drawn into the pas- senger compartment to further improve the defogging performance.

defog

helps

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets.

1. Push the

button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Heating and defogging This mode heats the interior and defogs the wind- shield.

c When the

position is selected, the air conditioner automatically turns on (however, the indicator light on the button will not come on and A/C will not appear on the display, if so equipped) if the outside tem- perature is more than 36(cid:176)F (2(cid:176)C). If in de- frost mode for more than one minute, the air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which the windshield. The mode automatically turns off, al- lowing outside air to be drawn into the pas- senger compartment to further improve the defogging performance.

defog

helps

Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.

Display screen, heater, air conditioner and audio systems 4-15

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

AIR CONDITIONER OPERATION Start the engine, turn the fan control dial to the desired position, and push in the button to activate the air conditioner. When the air condi- tioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.

1. Push the

button to the OFF position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the

button. The indicator light button will come on. (A/C will

on the appear on the display, if so equipped.)

5. Turn the temperature control dial to the de-

sired position.

c For quick cooling when the outside tem- perature is high, push the button to light on the ON position. The indicator the will button will come on. ( appear on the display, if so equipped.) Be

to the OFF position sure to return the for normal cooling. The indicator light on will ap- the pear on the display, if so equipped.) You may also select MAX A/C for quick cooling.

button will go off. (

Dehumidified heating This mode is used to heat and dehumidify the air. 1. Push the button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the

button on. The indicator light on the button will come on. (A/C will appear on the display, if so equipped.) The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the

position.

5. Turn the temperature control dial to the de-

sired position.

Operating tips c Keep the windows closed while the air con-

ditioner is in operation.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. For additional information on heating and cooling see (cid:147)Heater and air con- ditioner(cid:148) in this section(cid:148). The air recirculation ) button should always be in the OFF position for heating and defrosting.

4-16 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

WHA0536

WHA0537

Display screen, heater, air conditioner and audio systems 4-17

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

4-18 Display screen, heater, air conditioner and audio systems

WHA0538

WHA0539

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

SERVICING AIR CONDITIONER

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and lubricant recommendations(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

WHA0540

Display screen, heater, air conditioner and audio systems 4-19

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

AUDIO SYSTEM

RADIO Turn the ignition key to the ACC or ON position and press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area, and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 (cid:150) 30
miles (40 (cid:150) 48 km), with monaural (single chan- nel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.

Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.

4-20 Display screen, heater, air conditioner and audio systems

Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver.

Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist.

Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights. SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available and (cid:147)NO SAT(cid:148) is displayed when the SAT band option is selected unless optional satellite receiver and antenna are installed and an XMT or SIRIUS(cid:153) satellite radio service subscription is active. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna.

c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

c The player may skip while driving on

rough roads.

c The CD player sometimes cannot func- tion when the compartment tempera- ture is extremely high. Decrease the temperature before use.

c Do not expose the CD to direct sunlight. c CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

c The following CDs may not work properly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW) c Do not use the following CDs as they may cause the CD player to malfunction: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or

have abnormal edges

LHA0099
AUDIO OPERATION PRECAUTIONS Compact disc (CD) player c Only use high quality 4.7 inches (12 cm) round discs that have the (cid:147)COMPACT disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.

Display screen, heater, air conditioner and audio systems 4-21

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

PRESET ABC button Display

1. 2. 3. CD button 4. CD eject button 5. CD insert slot 6. MENU button AUDIO button 7. Station select buttons 8. 9. SEEK/TRACK button 10. PWR/VOL control knob 11. BAND select button FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) PWR/VOL control knob Turn the ignition key to the ACC or ON position, then push the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume.

4-22 Display screen, heater, air conditioner and audio systems

LHA0117

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

times for BAL (balance). Once the audio level is set the display will return back to radio or CD display mode after 7 seconds or the AUDIO button can be pressed again within 7 seconds to set the next audio level. Pressing the AUDIO button a fifth time will return the display back to radio or CD display mode.

Fader adjusts the sound level between the front and rear speakers, balance adjusts the sound level between the right and left speakers. Clock set

1. Press and hold the MENU button until

it

beeps (longer than 2 seconds).

2. The

hours will SEEK/TRACK ( hours.

start or

flashing. Press the ) to adjust

3. Press the MENU button until the radio beeps

to switch to the minute adjustment.

LHA0118
Adjusting tone quality and speaker balance

SEEK/TRACK ( utes.

or

4. The minutes will start

flashing. Press ) to adjust the min-

FM-AM radio operation

FM-AM band select

Push the reception.

button to change from AM to FM

The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.

SEEK/manual/SCAN tuning

When the button is pushed while the radio is playing, tuning mode is cycled between: SEEK tuning ! manual tuning ! SCAN mode (cid:147)TUNE(cid:148) and (cid:147)SCAN(cid:148) are shown in the display for each mode. No icon is displayed for SEEK mode.

WARNING

The radio should not be tuned while driv- ing so full attention may be given to ve- hicle operation.

To adjust the audio levels for bass, treble, fader, and balance, push the AUDIO button and adjust the level with the SEEK/TRACK button. Press the AUDIO button once for BASS (bass), twice for TREB (treble), 3 times for FAD (fader) and 4

clock set mode.

5. Press the MENU button again to exit the

The display will return to the regular clock display after 7 seconds, or you may press the MENU button again to return to the regular clock display.

SEEK tuning Push the SEEK/TRACK tuning button ( or ) for less than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is Display screen, heater, air conditioner and audio systems 4-23

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

and

If using the

pressed, and stops at the next broadcasting sta- button, once the highest tion. broadcasting station is reached, the radio contin- ues in the SEEK mode at the lowest broadcasting station. If using the button, once the lowest broadcasting station is reached, the radio contin- ues in the SEEK mode at the highest broadcast- ing station. Manual tuning Use the buttons for manual tuning. To move quickly through the channels, hold either of the tuning buttons down. SCAN tuning Push and hold the SEEK/TRACK tuning button SCAN illuminates in the display window, and the radio station blinks. SCAN tuning begins from low to high frequencies or high to low frequen- cies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for 5 seconds. When scanning, SCAN is solid and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the sta- tion display is solid. Pushing the button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station.

) for more than 1.5 seconds.

or

Press the PRESET ABC button to change be- tween the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active.

To store a radio station in a preset:

1. Select the desired preset by pressing PRE-

SET ABC.

2. Tune to the desired station. 3. Press the desired station select button for more than 3 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.

4. When the indicator illuminates in the display and the sound resumes, memorizing is com- plete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations. Compact disc (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot

LHA0119

Station memory operations

Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM and FM stations.

4-24 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Blank (no symbol): All selections are played repeatedly in sequence. When a new compact disc is inserted, the play pattern automatically changes to ALL.

CD EJECT button

button is pushed with a com-

When the pact disc loaded, the compact disc ejects. When the button is pushed while the com- pact disc is playing, the compact disc ejects and the system turns off.

DISC indicator light

This light is loaded into the player.

comes on when a compact disc

with the label side up. The compact disc is auto- matically pulled into the slot and starts to play.

If the radio is already operating, it automatically turns off and the compact disc begins to play.

CAUTION

Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.

CD button

When the CD button is pushed with a compact