2005 Nissan Titan Owners Manual

1. To begin, press and hold the two outer HomeLinkT buttons (to clear the memory) until the indicator light s1 blinks slowly (after 20 seconds). Release both buttons.

2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface.

Type B

Type A

3. Using both hands, simultaneously press and hold both the HomeLinkT button you want to program and the hand-held transmitter but- ton.

DO NOT release the buttons until step 4 has been completed.

4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a (cid:147)slow blink(cid:148) to a (cid:147)rapidly flashing blink(cid:148). This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro- grammed device, press and hold the pro- grammed HomeLinkT button (cid:151) releasing when the device begins to activate.

Instruments and controls 2-51

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

6. Press and release the (cid:147)smart(cid:148) or (cid:147)learn(cid:148) pro- gram button located on the garage door opener(cid:146)s motor to activate the (cid:147)training mode(cid:148). This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button.

NOTE:

Once you have pressed and released the program button on the garage door open- er(cid:146)s motor and the (cid:147)training light(cid:148) is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step.

7. Within 30 seconds of pressing and releas- ing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you(cid:146)ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training.

8. Your HomeLinkT button should now be pro- grammed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-8 only.)

Type B

LIC0677

5.

If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a (cid:147)rolling code(cid:148) garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another per- son for convenience.

2-52 Instruments and controls

all

previously

NOTE: Do not repeat step 1 unless you want to (cid:147)clear(cid:148) programmed HomeLinkT buttons. If you have any questions or are having difficulty programming your HomeLinkT buttons, refer to the HomeLinkT web site at: www.homelink.com or call 1-800-355-3515. PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (note steps 2 - 4 under (cid:147)Pro- gramming HomeLinkT(cid:148)) while you press and re- press ((cid:147)cycle(cid:148)) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).

NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the (cid:147)cycling(cid:148) process to prevent pos- sible damage to the garage door opener components.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLinkT Universal Transceiver button. The amber indicator light will illuminate while the signal is being transmitted. PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLinkT does not quickly learn the hand- held transmitter information: c replace the hand-held transmitter batteries

with new batteries.

c position the hand-held transmitter with its from the

facing

away

battery HomeLinkT surface.

area

c press and hold both the HomeLinkT and hand-held transmitter buttons without inter- ruption.

c position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the HomeLinkT surface. Hold the transmitter in that position for up to 15 seconds. If HomeLinkT is not programmed within that time, try holding the transmitter in another

position (cid:150) keeping the indicator light in view at all times.

If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). REPROGRAMMING A SINGLE HOMELINKT BUTTON To reprogram a HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT but- ton. Do not release the button until step 4
has been completed.

2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3 inches (26 - 76
mm) away from the HomeLinkT surface.

3. Press and hold the hand-held transmitter

button.

4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.

The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not affect any other programmed HomeLinkT buttons. IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLinkT. Consult the Owner(cid:146)s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLinkT Univer- sal Transceiver with your new transmitter information.

Instruments and controls 2-53

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

FCC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This de- vice must accept any interference that may be received, including interference that may cause undesired operation. This transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the device. DOC: ISTC 1763K1313
FCC I.D. CV2V67690

2-54 Instruments and controls

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

3 Pre-driving checks and adjustments

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Nissan vehicle immobilizer system (NVIS) keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4
Locking with power door lock switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Wide Open doors (if so equipped) . . . . . . . . . . . . . . . 3-5
Child safety rear door lock (Crew Cab models only) . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Remote keyless entry system (if so equipped). . . . . . . . . 3-7
How to use remote keyless entry system . . . . . . . . . . 3-7
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Fuel filler lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Fuel filler cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Tilt operation (if so equipped) . . . . . . . . . . . . . . . . . . . 3-12
Pedal position adjustment (if so equipped) . . . . . . . . . . 3-12
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Vanity mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
Inside mirror (if so equipped). . . . . . . . . . . . . . . . . . . . 3-14
Automatic anti-glare inside mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Truck box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
Tailgate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Tie down hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Automatic drive positioner (if so equipped) . . . . . . . . . . 3-20
Memory storage function . . . . . . . . . . . . . . . . . . . . . . . 3-21
Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/28/05—tbrooks X

KEYS

1.

WPD0128
Two master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip Key number plate Transponder chip

2. 3. 4. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate.

3-2 Pre-driving checks and adjustments

process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration pro- cess, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer Sys- tem (NVIS) during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.

A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) KEYS You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.

The master key can be used for all the locks.

The valet key cannot be used for the console box lock, the beside storage compartment lock, or the tailgate lock.

To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can dupli- cate your existing key. As many as five NVIS keys can be used with one vehicle. You should bring all NVIS keys that you have to your NISSAN dealer for registration. This is because the registration

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

DOORS

WARNING

c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.

c Before opening any door, always look

for and avoid oncoming traffic.

c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.

Turning the key one time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks all doors s4 . Opening and closing windows The driver(cid:146)s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. c To open the windows, turn the driver(cid:146)s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. c To close the windows, turn the driver(cid:146)s door key to the front of the vehicle for longer than 1 second after the door is locked.

Windows stop when the key cylinder is released.

Driver(cid:146)s side

LPD0240

LOCKING WITH KEY Manual To lock a door, turn the key toward the front of the vehicle s1 . To unlock, turn the key toward the rear s4 . Power The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front s1 of the vehicle locks all doors.

Pre-driving checks and adjustments 3-3

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Lockout protection When the power door lock switch (driver(cid:146)s or front passenger(cid:146)s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and unlock automatically. This helps to prevent the keys from being acci- dently locked inside the vehicle.

Inside lock

Door lock switch

LPD0241

WPD0317

LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .

LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the lock position s1 . When locking the door this way, be certain not to leave the key inside the vehicle.

To unlock all the doors without a key, push the door lock switch (driver(cid:146)s or front passenger(cid:146)s side) to the unlock position s2 .

3-4 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LPD0278
WIDE OPEN DOORS (if so equipped)

LPD0266
2. From the outside, pull the door handle s1

toward you.

LPD0267
From the inside, pull the inside door handle to- ward you. The door will unlock automatically.

CAUTION

Do not open the Wide Open door to the full open position while the fuel filler door is open; only open it as far as the first detent. Opening the door to the full open position may damage the fuel filler door and Wide Open door.

The Wide Open doors open nearly 180(cid:176) to allow access to the rear of the cab. 1. Open the driver(cid:146)s or passenger(cid:146)s door.

Pre-driving checks and adjustments 3-5

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

3. Open the door to the desired position.

3-6 Pre-driving checks and adjustments

LPD0265

LPD0242
CHILD SAFETY REAR DOOR LOCK (Crew Cab models only) Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

CAUTION

Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against

another object.

c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).

If a keyfob is lost or stolen, NISSAN rec- ommends erasing the ID code of that key- fob. This will prevent the keyfob from un- authorized use to unlock the vehicle. For information regarding the erasing proce- dure, please contact a NISSAN dealer.

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)

It is possible to lock/unlock all doors, turn on the interior lights and puddle lamps (if so equipped), and activate the panic alarm by using the keyfob from outside the vehicle.

Some settings for the keyfob, such as horn beep, can be adjusted. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For vehicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a maximum distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle. As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer. The keyfob will not function when: c the battery is discharged. c the distance between the vehicle and the

keyfob is over 33 ft (10 m).

The panic alarm will not activate when the key is in the ignition switch.

LPD0209

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all doors. 4. Push the

button on the keyfob. All the doors lock. The hazard warning lights flash twice and the horn beeps once to indicate all doors are locked.

Pre-driving checks and adjustments 3-7

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

c When the

button is pushed with all doors locked, the hazard warning lights flash twice and the horn beeps once as a re- minder that the doors are already locked.

c If a door is open and you push the

button, the doors will lock but the horn will not beep and the hazard warning lights will not flash.

The horn may or may not beep. For vehicles without navigation system, refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section. For ve- hicles with navigation system, refer to (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) sec- tion later in this manual.

3-8 Pre-driving checks and adjustments

button on the keyfob again within

Push the 5 seconds. c All doors unlock. c The hazard warning lights flash once if all

doors are completely closed.

The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the off position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 1 minute unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and

the key is turned from OFF to ON.

Linking the keyfob to automatic drive positioner memory If the vehicle is equipped with automatic drive positioner, the keyfob can be linked to a memory setting. See (cid:147)Automatic driver positioner(cid:148) later in this section.

LPD0210

button on the keyfob once.

Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The hazard warning lights flash once if all doors are completely closed with the ignition key in any position except the ON position. c The interior lights and puddle lamps (if so equipped) turn on and the light timer acti- vates for 30 seconds when the interior light switch is in the DOOR position with the ignition key in any position except the ON position.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

buttons for at least 2 seconds.

buttons for at least 2 seconds

To deactivate: Press and hold the and The hazard warning lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. Using the interior lights Push the button on the keyfob once to turn on the interior lights and puddle lamps (if so equipped). For additional information, refer to (cid:147)Interior light(cid:148) in the (cid:147)Instruments and controls(cid:148) section earlier in this manual.

LPD0211

LPD0262

Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for 25
seconds. The panic alarm stops when: c it has run for 25 seconds, or c any button is pushed on the keyfob.

Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob.

NOTE: If you change the horn beep and lamp flash feature with the keyfob, the display screen (if so equipped) will not show the current mode and cannot be used to change the mode. Use the keyfob to return to the pre- vious mode and re-enable the display screen control.

Pre-driving checks and adjustments 3-9

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

HOOD

FUEL FILLER LID

LPD0244

LPD0263

s1 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly.

s2 Push the lever at the front of the hood to the side as illustrated with your fingertips and raise the hood.

When closing the hood, lower it slowly and make sure it locks into place.

WARNING

c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.

c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

FUEL FILLER CAP The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.

For additional information, see (cid:147)Fuel recommen- dation(cid:148) and (cid:147)Flexible fuel vehicle (FFV) fuel rec- ommendation(cid:148) in the (cid:147)Technical and consumer information(cid:148) section later in this manual.

3-10 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

WARNING

c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.

c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to

attempt to start your vehicle.

c Do not fill a portable fuel container on a truck bed liner, rubber truck bed mad, or other insulating material. Static elec- tricity can cause an explosion of flam- mable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the

ground when filling.

(cid:150) Do not use electronic devices when

filling.

(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.

(cid:150) Use only approved portable fuel con-

tainers for flammable liquid.

CAUTION

c Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.

c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap mal- properly may cause the function indicator lamp (MIL) to illumi- nate. If the lamp illuminates be- cause the fuel filler cap is loose or missing, tighten or install the cap and to continue vehicle. The lamp should turn off after a

drive

the

lamp few driving trips. If the does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. c For additional

information, see the (cid:147)Malfunction indicator lamp (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.

Pre-driving checks and adjustments 3-11

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

STEERING WHEEL

PEDAL POSITION ADJUSTMENT (if so equipped)

CAUTION

Do not adjust the pedal position with your foot on the pedal.

LPD0254

TILT OPERATION (if so equipped) Pull the lock lever forward and hold it to adjust the steering wheel up or down to the desired posi- tion. Release the lock lever to lock the steering wheel in place.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

LPD0255
The accelerator and brake pedals can be ad- justed for driving comfort.

Use the pedal adjusting switch to adjust the brake and accelerator pedal position forward s1
or backward s2 . Pedal adjustment can only be performed when: c Ignition switch is in the OFF or ACC position c Ignition switch is ON and the selector lever

is in the P (Park) position

The brake and accelerator pedals cannot be ad- justed separately.

3-12 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

SUN VISORS

CAUTION

c Do not store the sun visor before return- ing the extension to its original position.

c Do not pull the extension sun visor forc-

edly downward.

LPD0264

s1 To block glare from the front, swing down the

Type B

main sun visor.

s2 To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side.

s3 To block glare from the side and front, swing

down the sub-sun visor (if so equipped).

s4 Slide the extension sun visor (if so equipped)

in or out as needed.

Type A

LPD0273

Pre-driving checks and adjustments 3-13

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

MIRRORS

WPD0168

LPD0257

WPD0126

Type A

VANITY MIRRORS To access the vanity mirror, pull the sun visor down and flip open the mirror cover (if so equipped). Some vanity mirrors are illuminated and turn on when the mirror cover is open.

Type B

INSIDE MIRROR (if so equipped) The night position s1 reduces glare from the headlights of vehicles behind you at night. Use the day position s2 when driving in daylight hours.

WARNING

Use the night position only when neces- sary, because it reduces rear view clarity.

3-14 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LPD0280

AUTO position

AUTO indicator light Sensor (on back of mirror) Sensor

1. 2. OFF position 3. 4. 5. AUTOMATIC ANTI-GLARE INSIDE MIRROR (if so equipped) The inside mirror is designed so that it automati- cally changes reflection according to the intensity of the headlights of the vehicle following you.

When the inside mirror switch is in the AUTO position, excessive glare from the headlights of the vehicle behind you will be reduced. The

AUTO indicator light will be on. When the switch on the inside mirror is in the OFF position, the inside mirror will operate normally. Do not hang any object on the sensor or apply glass cleaner. Doing so will reduce the sensitivity of the sensor, resulting in improper operation. OUTSIDE MIRRORS

WARNING

c Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.

c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.

LPD0237

Electric control type (if so equipped) The outside mirror remote control will operate only when the ignition switch is in the ACC or ON position. Move the small switch s1 to select the right or left mirror. Adjust each mirror to the desired position using the large switch s2 .

Pre-driving checks and adjustments 3-15

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Use the outside mirror remote control to adjust the top portion of the trailer tow mirror. The lower portion of the trailer tow mirror can be moved manually in any direction for a better rear view.

WPD0170

LPD0279

Manual control type The outside mirror can be moved in any direction for a better rear view.

Trailer tow mirrors (if so equipped)

WARNING

c Objects viewed in the convex portion of the trailer tow mirror are closer than they appear. Be careful when changing lanes or turning. Using only the convex mirror could cause an accident. Use the other mirrors or glance over your shoul- der to properly judge distances to other objects.

c Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.

3-16 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Heated mirrors (if so equipped) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. For addi- tional information, see (cid:147)Rear window and outside mirror (if so equipped) defroster switch(cid:148) in the (cid:147)Instrument and controls(cid:148) section of this manual.

LPD0268
Pull the trailer tow mirror outward to extend it to the desired position for better visibility while tow- ing a trailer.

WARNING

Do not extend or retract mirrors while driv- ing. You may lose control of your vehicle and cause an accident.

CAUTION

Driving in tight spaces with mirrors ex- tended may cause damage to the vehicle.

Type A

LPD0259

Foldable outside mirrors Pull the outside mirror toward the door to fold it.

Pre-driving checks and adjustments 3-17

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

TRUCK BOX

Type B

LPD0269

LPD0270

TAILGATE Opening the tailgate Pull the tailgate handle upward and lower the tailgate. The support cables hold the tailgate open.

When closing the tailgate, make sure the latches are securely locked. Do not drive the vehicle with the tailgate down, unless equipped with NISSAN(cid:146)s Bed Extender (accessory) or equivalent in the extended position.

3-18 Pre-driving checks and adjustments

For proper truck box loading see (cid:147)Vehicle loading information(cid:148) in the (cid:147)Technical and consumer in- formation(cid:148) section of this manual.

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

4. Slide the tailgate out of the right side hinge. Installing the tailgate 1. 2. Hold the tailgate at a 45 degree angle and

Insert the tailgate into the right side hinge.

insert into the left side hinge.

3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables.

4. Close the tailgate securely.

LPD0272

Locking the tailgate To unlock the tailgate, turn the key toward the passenger side of the vehicle s1 . To lock, turn the key toward the driver side s2 .

LPD0271

Removing the tailgate 1. Release the tailgate support cables.

CAUTION

c The tailgate is heavy. Two people should remove or install it. Be careful not to drop it during removal.

c After releasing the support cables, do not let the tailgate rest on the bumper.

2. Hold the tailgate at a 45 degree angle.

3. Pull the tailgate out from the left side hinge.

Pre-driving checks and adjustments 3-19

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

AUTOMATIC DRIVE POSITIONER (if so equipped)

The automatic drive positioner system has two features: c Memory storage function c Entry/exit function

LTI0102

TIE DOWN HOOKS For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box. c The weight of the cargo load must be evenly distributed over both the front and the rear axles.

c All cargo should be securely fastened with ropes or straps to prevent it from shifting or sliding within the vehicle.

3-20 Pre-driving checks and adjustments

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LPD0260

MEMORY STORAGE FUNCTION Two positions for the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory sys- tem.

1. Set the automatic transmission selector le-

ver to the P (Park) position.

2. Turn the ignition ON.

3. Adjust

the driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional infor- mation, see (cid:147)Seats(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint sys- tem(cid:148) section and (cid:147)Pedal position adjust- ment(cid:148) and (cid:147)Outside mirrors(cid:148) earlier in this section.

During this step, do not turn the ignition to any position other than ON.

4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second.

The indicator light for the pushed memory switch will come on and stay on for approxi- mately 5 seconds after pushing the switch. After the indicator light goes off, the se- lected positions are stored in the selected memory (1 or 2).

If a new memory is stored in the same memory switch, the previous memory will be deleted. Linking a keyfob to a stored memory position Each keyfob can be linked to a stored memory position (memory switch 1 or 2) with the follow- ing procedure.

1. Follow the steps for storing a memory posi-

tion.

2. While the indicator light for the memory switch being set is illuminated for 5 sec- button on the keyfob. onds, press the The indicator light will blink. After the indica- tor light goes off, the keyfob is linked to that memory setting.

With the key removed from the ignition switch, press the button on the keyfob. The driv- er(cid:146)s seat, accelerator and brake pedals, and out- side mirrors will move to the memorized position.

NOTE: If a new memory is saved to the memory switch, the keyfob must be re-linked. Confirming memory storage c Turn the ignition ON and push the SET If the main memory has not been switch. stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indica- tor light will stay on for approximately 5 sec- onds.

c If the battery cable is disconnected, or if the fuse opens, the memory will be canceled. In such a case, reset the desired positions using the following procedures.

Pre-driving checks and adjustments 3-21

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

1. Open and close the driver(cid:146)s door more than two times with the ignition key in the LOCK position.

2. Reset the desired position using the previ-

ous procedure.

Selecting the memorized position 1. Set the automatic transmission selector le-

ver to the P (Park) position.

2. Turn the ignition ON.

3. Push the memory switch (1 or 2) fully for at

least 1 second.

The driver(cid:146)s seat, accelerator and brake pedals, and outside mirrors will move to the memorized position with the indicator light blinking, and then the light will stay on for approximately 5 seconds. ENTRY/EXIT FUNCTION This system is designed so that the driver(cid:146)s seat will automatically move when the automatic transmission selector lever is in the P (Park) position. This allows the driver to get into and out of the driver(cid:146)s seat more easily. The driver(cid:146)s seat will slide backward: c When the driver(cid:146)s door is opened with the

ignition key turned to LOCK.

3-22 Pre-driving checks and adjustments

c When the ignition key is turned from ACC to LOCK with the driver(cid:146)s door open while the automatic transmission selector lever is in the P (Park) position.

The driver(cid:146)s seat will return to the previous posi- tion: c When the key is inserted into the ignition

switch.

c When the driver(cid:146)s door is closed with the key

turned to LOCK.

c When the key is turned from ACC to ON while the automatic transmission selector lever is in the P (Park) position.

The entry/exit function can be adjusted or can- celed. For vehicles with navigation system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio sys- tems(cid:148) section of this manual. For vehicles without navigation system, see your NISSAN dealer. SYSTEM OPERATION The automatic drive positioner system will not work or will stop operating under the following conditions: c When the vehicle speed is above 4 MPH (7

km/h).

c When any two or more of

the memory switches are simultaneously pushed while the automatic drive positioner is operating. c When the adjusting switch for the driver(cid:146)s seat is turned on while the automatic drive positioner is operating.

c When the memory switch (1 or 2) is not

pushed for at least 1 second.

c When the seat has been already moved to

the memorized position.

c When no seat position is stored in the

memory switch.

The automatic drive positioner system can be adjusted and canceled. For vehicles with naviga- tion system, see (cid:147)Vehicle electronic systems(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section of this manual. For ve- hicles without navigation system, see your NISSAN dealer.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

4 Display screen, heater, air conditioner and audio systems

Control panel buttons (if so equipped) . . . . . . . . . . . . . . . 4-2
Names of the components. . . . . . . . . . . . . . . . . . . . . . . 4-3
How to use joystick and (cid:147)ENTER(cid:148) button . . . . . . . . . . 4-3
How to use (cid:147)PREV(cid:148) button . . . . . . . . . . . . . . . . . . . . . . 4-3
Setting up the start-up screen . . . . . . . . . . . . . . . . . . . 4-3
How to use the (cid:147)TRIP(cid:148) button . . . . . . . . . . . . . . . . . . . . 4-4
How to use the (cid:147)SETTING(cid:148) button. . . . . . . . . . . . . . . . 4-7
Setting the display (Audio or HVAC display): . . . . . . 4-7
button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . 4-13
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Air conditioner operation . . . . . . . . . . . . . . . . . . . . . . . 4-16
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Satellite radio reception (if so equipped) . . . . . . . . . 4-20
Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-21
FM-AM radio with compact disc (CD) player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
FM-AM-SAT radio with compact disc (CD) changer (Type A, B, C and D) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
Rear audio controls (if so equipped) . . . . . . . . . . . . . 4-38
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

NISSAN mobile entertainment system (MES) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
Digital video disc (DVD) player controls . . . . . . . . . . 4-40
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
Flip-down screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
Playing a digital video disc (DVD) . . . . . . . . . . . . . . . 4-42
Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 4-45
How to handle the DVD . . . . . . . . . . . . . . . . . . . . . . . . 4-46
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-48

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/28/05—tbrooks X

WARNING

c Positioning of the heating or air condi- tioning controls and display controls should not be done while driving in or- der that full attention may be given to the driving operation.

c Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock.

c Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.

c In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ignoring such conditions may lead to accidents, fire or electrical shock.

CONTROL PANEL BUTTONS (if so equipped)

When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start.

LHA0388

Reference symbols: (cid:147)ENTER(cid:148) button (cid:151) This is a button on the con- trol panel.

4-2 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

If you do not touch the button or screen key for more than 1 minute on the TRIP, SETTING or START-UP screen, the screen will change to TRIP screen automatically. To proceed to the next step, refer to the separate Navigation System Owner(cid:146)s Manual.

brightness control button (P. 4-12)

(cid:147)Display(cid:148) key (cid:151) This is a select key on the screen. By selecting this key you can proceed to the next function. NAMES OF THE COMPONENTS 1. 2. PREV (previous) button (P. 4-3) 3. Joystick and ENTER push button (P. 4-3) 4. SETTING button (P. 4-7) 5. TRIP drive computer button (P. 4-4) 6. DEST button* 7. ROUTE button* 8. MAP button* 9. GUIDE VOICE button* 10. zoom out button* 11. zoom in button* *For Navigation system control buttons, refer to the separate Navigation System Owner(cid:146)s Manual.

HOW TO USE JOYSTICK AND (cid:147)ENTER(cid:148) BUTTON Choose an item on the display using the joystick and push the (cid:147)ENTER(cid:148) button for operation. HOW TO USE (cid:147)PREV(cid:148) BUTTON This button has two functions. c Go back to the previous display (cancel). If you touch (cid:147)PREV(cid:148) button during setup, the setup will be canceled and/or the display will return to the previous screen. c Finish setup. If you touch this button after the setup is com- pleted, the setup will start over, and the display will return to the climate control or audio mode and Navigation screen. SETTING UP THE START-UP SCREEN When you turn the ignition key to ACC or ON, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the (cid:147)I AGREE(cid:148) (English) or (cid:147)ENTER(cid:148) (Fran(cid:231)ais) key then push the (cid:147)ENTER(cid:148) button. If you do not push the (cid:147)ENTER(cid:148) button, the Navigation system will not proceed to the next step display.

Display screen, heater, air conditioner and audio systems 4-3

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/28/05—tbrooks X

LHA0398
HOW TO USE THE (cid:147)TRIP(cid:148) BUTTON When the (cid:147)TRIP(cid:148) button is pushed, the following modes will display on the screen. Warning message (if there are any) ! TRIP 1
(Elapsed Time, Driving Distance, Average Speed) ! TRIP 2 ! FUEL ECONOMY (Average Fuel Economy, Distance to Empty) ! MAINTE- NANCE (Engine Oil, Tire Rotation and Tire Pres- sure (cid:151) if so equipped) ! OFF.

LHA0399

LHA0402

Trip 1, trip 2 and fuel economy items To reset the TRIP 1, TRIP 2 and FUEL ECONOMY, select the (cid:147)RESET(cid:148) key using the joystick and push the (cid:147)ENTER(cid:148) button or push the (cid:147)TRIP(cid:148) button for more than approximately 1.5 seconds.

Maintenance items You can set the engine oil and the tire rotation interval. To display the setting of the maintenance interval, select the (cid:147)Engine Oil(cid:148) or (cid:147)Tire Rotation(cid:148) key using the joystick and push the (cid:147)ENTER(cid:148) button.

4-4 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

the maintenance interval, select

LHA0400
the To set (cid:147)Maintenance Schedule(cid:148) key by using the joy- stick and push the joystick to right or left. To reset the maintenance interval, select the (cid:147)Re- set(cid:148) key using the joystick and push the (cid:147)EN- TER(cid:148) button. To display the MAINTENANCE INFORMATION automatically when set trip distance is reached, select the (cid:147)Display Maintenance Notifica- tion(cid:148) key and push the (cid:147)ENTER(cid:148) button.

LHA0401

LHA0483
The (cid:147)MAINTENANCE NOTICE(cid:148) screen ((cid:147)EN- GINE OIL(cid:148) and (cid:147)TIRE ROTATION(cid:148)) will be auto- matically displayed as shown when both of the following conditions are met: c the vehicle is driven the set distance and the

ignition key is turned OFF.

c the ignition key is turned ON the next time

the vehicle will be driving.

To return to the previous display after the (cid:147)MAIN- TENANCE NOTICE(cid:148) screen is displayed, press the PREV button.

Display screen, heater, air conditioner and audio systems 4-5

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Tire pressure rises and falls depending on the heat caused by the vehicle(cid:146)s operation and the outside temperature. In case of low tire pressure, a message is dis- played on the screen: FLAT TIRE (cid:151) low tire air pressure.

WARNING

When a spare tire is mounted or a wheel is replaced, tire pressure will not be indi- cated and the low tire pressure warning system will not function. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

The (cid:147)MAINTENANCE NOTICE(cid:148) screen displays each time the key is turned ON until one of the following conditions are met: c (cid:147)RESET(cid:148) is selected. c (cid:147)Display Maintenance and Notification(cid:148) is

set OFF.

c the maintenance interval is set again.

LHA0403

Tire pressure information To view (cid:147)TIRE PRESSURE(cid:148) information, push the (cid:147)TRIP(cid:148) button repeatedly until the (cid:147)MAINTE- NANCE(cid:148) screen is displayed. Select (cid:147)TIRE PRESSURE(cid:148) using the joystick and push the (cid:147)ENTER(cid:148) button.

Pressure indication in ** psi on the screen indi- cates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.

4-6 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0268

HOW TO USE THE (cid:147)SETTING(cid:148) BUTTON To adjust the various settings within the display screen press the(cid:147)SETTING(cid:148) button. After pressing the SETTING button a menu will be shown on the display screen which will allow you to program several functions such as the display screen appearance, programmable fea- tures for your vehicles electronics system and other system settings such as your clock. To make a selection from this mode use the joystick and press the (cid:147)ENTER(cid:148) button.

SETTING THE DISPLAY (Audio or HVAC display): The audio or HVAC reading can be displayed at the bottom of the screen. Choose the (cid:147)Audio(cid:148) or (cid:147)HVAC(cid:148) (Heater and air conditioner) key to be displayed at the bottom, by using the joystick and pressing the ENTER button to select or deselect the key. The setting condition will normally appear on the screen. To return to the setting screen, push the (cid:147)SETTING(cid:148) button or (cid:147)PREV(cid:148) button. Display settings The DISPLAY SETTINGS screen will appear af- ter pushing the (cid:147)SETTING(cid:148) button, selecting (cid:147)Display(cid:148) key and pushing the (cid:147)ENTER(cid:148) but- ton. Brightness/Contrast/Map Background: To adjust the brightness and contrast of the screen, select the (cid:147)Brightness/contrast(cid:148) key and push the (cid:147)ENTER(cid:148) button. You can then use the joystick to adjust the brightness to Darker or Brighter and the contrast to Lower or Higher. For information on Map Background, please refer to the separate Navigation System Owner(cid:146)s Manual.

Display Off: To turn off the screen, push the (cid:147)SETTING(cid:148) button and select the (cid:147)Display(cid:148) key and (cid:147)Dis- play Off(cid:148) key. The indicator of the (cid:147)Display Off(cid:148) will turn to amber. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5 seconds after the operation is finished on the map display in the Audio, HVAC (Heater and air conditioner), SETTING or VE- HICLE INFO modes. To turn on the screen, push the (cid:147)SETTING(cid:148) button and select the (cid:147)Display(cid:148) key and (cid:147)Dis- play Off(cid:148) key, then set the screen to on by pushing the (cid:147)ENTER(cid:148) button. Setting Audio or HVAC display: Choose the (cid:147)Audio(cid:148) or (cid:147)HVAC(cid:148) (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC setting condition will normally appear on the screen. To return to the setting screen, push the (cid:147)SET- TING(cid:148) button or (cid:147)PREV(cid:148) button.

Display screen, heater, air conditioner and audio systems 4-7

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0382

LHA0381

LHA0261

Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the (cid:147)Vehicle Elec- tronic Systems(cid:148) key with the joystick and push- ing the (cid:147)ENTER(cid:148) button. To set the various electronic systems operating conditions, select the applicable item using the joystick, and push the (cid:147)ENTER(cid:148) button. The indicator light, box at left of selected item, alter- nately turns on and off each time the (cid:147)ENTER(cid:148) button is pressed. Indicator light is illuminated (cid:151) ON Indicator light is not illuminated (cid:151) OFF

4-8 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

Speed dependent wiper: This key allows you to turn on or turn off the driving speed dependent intermittent wiper func- tion. Return all settings to default: When this key is selected and turned on using the (cid:147)ENTER(cid:148) button, all settings made by VE- HICLE ELECTRONICS will return to the default settings.

Adjust driver seat when exiting vehicle:

NOTE:

With this option ON, the driver(cid:146)s seat automati- cally moves back and returns to the original po- sition for ease of exit and entry. Remote unlock driver(cid:146)s door first:

This option allows you to select which doors will unlock first during an unlocking operation: Only the driver(cid:146)s door ˆ! All the doors Keyless remote response (cid:151) horn:

This key allows you to change the horn chirp mode that occurs when pressing the LOCK or UNLOCK button on the keyfob.

NOTE:

If you change the horn beep or the lamp flash feature with the keyfob, the display screen will not show the current mode. Use the keyfob to return to the previous mode and re-enable the display screen control.

Keyless remote response (cid:151) lights:

This key allows you to change the hazard indica- tor flash mode that occurs when pressing the LOCK or UNLOCK button on the keyfob.

If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.

Auto re-lock time:

This key allows you to set the length of time before doors auto re-lock. Sensitivity of automatic headlights:

This key allows you to set the sensitivity of the automatic headlights: c Lower- less sensitive, automatic headlights will take longer to come on when the head- light sensor senses less ambient light.

c Higher- more sensitive, automatic head- lights will come on quicker when the head- light sensor senses less ambient light.

Automatic headlights off delay:

This key allows you to set the length of time before the automatic headlights turn off after exiting the vehicle.

Display screen, heater, air conditioner and audio systems 4-9

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0262

LHA0270

LHA0271

System settings Language/Unit The LANGUAGE/UNIT screen will appear when selecting the (cid:147)Language/Unit(cid:148) key and push- ing the (cid:147)ENTER(cid:148) button. Language: English or French Unit: US (cid:151) mile, (cid:176)F, MPG

Metric (cid:151) km, (cid:176)C, L/100 km

You can select the language and unit using the joystick and (cid:147)ENTER(cid:148) button.

Clock Adjusting the time: Select the (cid:147)Hours(cid:148) or (cid:147)Minutes(cid:148) key and move the joystick to the right or left to adjust the time. The time will change step by step. After completion of (cid:147)PREV(cid:148) button.

the setting, press the

Setting daylight savings time: Use the (cid:147)Daylight Saving Time(cid:148) key to adjust the clock to daylight savings time. ON: The displayed time advances by 1 hour. OFF: The current time is displayed.

4-10 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

LHA0272

LHA0273

Adjusting the time to the GPS: Select the (cid:147)Auto Adjust(cid:148) key. The time will be reset to the GPS time.

Selecting the time zone: 1. Select the (cid:147)Select Time Zone(cid:148) key. The [TIME ZONE] screen will appear.

LHA0274
2. Select one of the following zones depending

on the current location. c Pacific zone c Mountain zone c Central zone c Eastern zone c Atlantic zone c Newfoundland zone

After selection, the [CLOCK SETTINGS] screen will appear.

Display screen, heater, air conditioner and audio systems 4-11

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

VENTILATORS

The GPS time (manual time) corresponding to the selected zone will be displayed. Pacific zone has been set as the initial (default) setting. Beep setting With this option ON, a beep will sound if any audio button is pushed.

BUTTON

To change the display brightness, push the button. Pushing the button again will change the display to DAY or NIGHT display. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the (cid:147)PREV(cid:148) button is pushed, the display will return to the previous display.

Adjust air flow direction for the driver and pas- senger side s1 , center s2 , and rear passenger (if so equipped) s3 ventilators by moving the venti- lator slide and/or ventilator assemblies.

LHA0410

4-12 Display screen, heater, air conditioner and audio systems

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

HEATER AND AIR CONDITIONER (manual)

WARNING

c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

c Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation.

1. 2. 3. 4. 5. 6.

Fan speed control dial Air recirculation button Temperature control dial Air conditioner button Air flow control dial Rear window defroster switch (if so equipped) CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.

WHA0535

Air flow control dial The air flow control dial allows you to select the air flow outlets. MAX A/C

(cid:151) Air flows from center and side

vents with maximum cooling (air conditioning).

(cid:151) Air flows from center and side

ventilators.

(cid:151) Air flows from center and side

ventilators and the front and rear floor outlets.

(cid:151) Air flows mainly from the front

and rear floor outlets.

Display screen, heater, air conditioner and audio systems 4-13

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

(cid:151) Air flows from defroster outlets

and the front and rear floor outlets.

(cid:151) Air flows mainly from defroster

outlets.

The air flow control dial also has intermediate positions which allow the air flow to be distrib- uted between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left. To increase the temperature, turn the dial to the right.

Air recirculation button

ON position: Push the the vehicle.

button to recirculate air inside

button to the on position when:

Push the c driving on a dusty road. c to prevent traffic fumes from entering pas-

senger compartment.

c for maximum cooling when using the air con-

ditioner.

OFF position: button again to turn air recircula- Push the tion off. Outside air is drawn into the passenger compartment and distributed through the se- lected outlet. Use the off position for normal heater or air con- ditioner operation.

Air conditioner button

Start the engine, turn the fan control dial to the desired position and push the button to turn on the air conditioner. A/C will appear on the display when the air conditioner is operating. To turn off the air conditioner, push the button again, the display will show A/C OFF. The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch (if so equipped) For more information about the rear window de- froster switch, see (cid:147)Rear window defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. Heated mirror switch (if so equipped) For more information about the heated mirror switch, see (cid:147)Heated mirror switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section of this manual.

4-14 Display screen, heater, air conditioner and audio systems

HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets.

1. Push the

button to the OFF position for normal heating. The indicator light on the will ap- pear on the display, if so equipped.)

button will go off. (

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Ventilation This mode directs outside air to the side and center ventilators.

1. Push the

button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

c To quickly remove ice or fog from the win- dows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. c When the

position is selected, the air conditioner automatically turns on (however, the indicator light on the button will not come on and A/C will not appear on the display, if so equipped) if the outside tem- perature is more than 36(cid:176)F (2(cid:176)C). If in de- frost mode for more than one minute, the air conditioning system will continue to operate until the fan control dial is turned to OFF or

the vehicle is shut off, even if the air flow control dial is turned to a position other than position. This dehumidifies the air the which the windshield. The mode automatically turns off, al- lowing outside air to be drawn into the pas- senger compartment to further improve the defogging performance.

defog

helps

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets.

1. Push the

button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Heating and defogging This mode heats the interior and defogs the wind- shield.

c When the

position is selected, the air conditioner automatically turns on (however, the indicator light on the button will not come on and A/C will not appear on the display, if so equipped) if the outside tem- perature is more than 36(cid:176)F (2(cid:176)C). If in de- frost mode for more than one minute, the air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which the windshield. The mode automatically turns off, al- lowing outside air to be drawn into the pas- senger compartment to further improve the defogging performance.

defog

helps

Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.

Display screen, heater, air conditioner and audio systems 4-15

Z REVIEW COPY—2005 Titan (tzw) Owners Manual—USA_English (nna) 02/26/05—tbrooks X

AIR CONDITIONER OPERATION Start the engine, turn the fan control dial to the desired position, and push in the button to activate the air conditioner. When the air condi- tioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.

1. Push the

button to the OFF position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the

button. The indicator light button will come on. (A/C will

on the appear on the display, if so equipped.)

5. Turn the temperature control dial to the de-

sired position.

c For quick cooling when the outside tem- perature is high, push the button to light on the ON position. The indicator the will button will come on. ( appear on the display, if so equipped.) Be

to the OFF position sure to return the for normal cooling. The indicator light on will ap- the pear on the display, if so equipped.) You may also select MAX A/C for quick cooling.

button will go off. (

Dehumidified heating This mode is used to heat and dehumidify the air. 1. Push the button to the OFF position. button will will appear on the display, if so

The indicator light on the go off. ( equipped.)

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the

button on. The indicator light on the button will come on. (A/C will appear on the display, if so equipped.) The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the

position.

5. Turn the temperature control dial to the de-

sired position.

Operating tips c Keep the windows closed while the air con-

ditioner is in operation.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your