Download PDF Manual

cludes a supplemental air bag. Most U.S. states and Canadian provinces or territories specify that seat belts be worn at all times when a vehicle is being driven.


1-28 Safety(cid:151)Seats, seat belts and supplemental air bags


SSS0136


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint.


SSS0134


SSS0016


WARNING


c The seat belt should be properly ad- justed to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an acci- dent. Serious injury or death can occur if the seat belt is not worn properly.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-29


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c Be sure the seat belt tongue is securely


fastened to the proper buckle.


c Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness.


c Do not allow more than one person to


use the same seat belt.


c Never carry more people in the vehicle


than there are seat belts.


c If the seat belt warning light glows con- tinuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indicate a mal- function in the system. Have the system checked by a NISSAN dealer.


c Once the pre-tensioner seat belt has activated, it cannot be reused and must be replaced together with the retractor. See your NISSAN dealer.


c Removal and installation of the pre- tensioner seat belt system components should be done by a NISSAN dealer.


SSS0014


WARNING


c Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. c Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident.


1-30 Safety(cid:151)Seats, seat belts and supplemental air bags


and


attaching


c All seat belt assemblies, including re- tractors hardware, should be inspected after any collision by a NISSAN dealer. NISSAN recom- mends that all seat belt assemblies in use during a collision be replaced un- less the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. c All child restraints and attaching hard- ware should be inspected after any col- lision. Always follow the restraint manufacturer(cid:146)s inspection instructions and replacement recommendations. The child restraints should be replaced if they are damaged.


CHILD SAFETY Children need adults to help protect them. They need to be properly restrained.


The proper restraint depends on the child(cid:146)s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child re- straints are available for children who outgrow rear facing child restraints.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING


Infants and children need special protec- tion. The vehicle(cid:146)s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fit- ting seat belt could cause serious or fatal injury. Always use appropriate child restraints.


All U.S. states and Canadian provinces or terri- tories require the use of approved child restraints for infants and small children. See (cid:147)Child Re- straints(cid:148) later in this section.


In addition, there are many types of child re- straints available for larger children which should be used for maximum protection. NISSAN recommends that all pre-teens and children be restrained in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. This is especially important because your vehicle has a supplemental restraint system (Air bag system) for the front passenger. See (cid:147)Supplemental restraint system(cid:148) earlier in this section.


Infants and small children NISSAN recommends that infants and small chil- dren be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Ca- nadian Motor Vehicle Safety Standards. You should choose a child restraint that fits your ve- hicle and always follow the manufacturer(cid:146)s in- structions for installation and use. Larger children Children who are too large for child restraints should be seated and restrained by the seat belts which are provided.


If the child(cid:146)s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that the shoulder belt is properly posi- tioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Mo- tor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.


WARNING


Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop.


PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as pos- sible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations. INJURED PERSONS NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-31


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


THREE-POINT TYPE SEAT BELT WITH RETRACTOR


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times.


c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.


c For the most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.


Fastening the seat belts 1. Adjust the seat. See (cid:147)Seats(cid:148) earlier in this


section.


WRS0137
s2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.


The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.


WRS0138
s3 Position the lap belt portion low and snug


on the hips as shown.


s4 Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest.


The right front passenger seat and the rear seat- ing positions three-point seat belts have a cinch- ing mechanism for child restraint installation. It is referred to as the automatic locking mode or child restraint mode. When automatic locking mode is activated the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully


1-32 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


retracted. Once retracted, the seat belt is in the emergency locking mode. See (cid:147)Child restraints(cid:148) later in this section for more information. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passen- ger, the locking mode should not be acti- vated. If it is activated it may cause uncom- fortable seat belt It can also change the operation of the front passen- ger air bag. See (cid:147)Front passenger air bag and status light(cid:148) earlier in this section.


tension.


WARNING


When fastening the seat belts, be certain that the seatbacks are completely se- cured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop.


c Grasp the shoulder belt and pull forward quickly. The retractor should lock and re- strict further belt movement.


If the retractor does not lock during this check or if you have any questions about seat belt opera- tion, see a NISSAN dealer.


WRS0139


Unfastening the seat belts s1 To unfasten the seat belt, press the button on the buckle. The seat belt automatically re- tracts.


Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods: c When the seat belt is pulled quickly from the


retractor.


c When the vehicle slows down rapidly. To increase your confidence in the seat belts, check the operation as follows.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-33


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING


c After adjustment, release the adjust- ment button and try to move the shoul- der belt anchor up and down to make sure it is securely fixed in position.


c The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effec- tiveness of the entire restraint system and increase the chance or severity of injury in an accident.


LRS0394


Center of the rear seat Selecting correct set of seat belts: The center seat belt buckle is identified by the CENTER mark. The center seat belt tongue can be fastened only into the center seat belt buckle.


Front seats


LRS0242


Shoulder belt height adjustment (front outboard seats) The shoulder belt anchor height should be ad- justed to the position best for you. (See (cid:147)Precau- tions on seat belt usage(cid:148) earlier in this section.) To adjust, pull outs1 the adjustment button and move the shoulder belt anchors2 to the desired position, so the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Re- lease the adjustment button to lock the shoulder belt anchor into position.


1-34 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WRS0190


WRS0445


TWO-POINT TYPE SEAT BELT WITHOUT RETRACTOR (center of the front bench seat) (if so equipped)


Fastening the belts 1.


Insert the tongue into the buckle until you hear and feel the latch engage.


WRS0446
2. Tighten the belt by pulling the free end of the


belt away from the tongue.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-35


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WRS0447
3. Position the lap belt low and snug on the


hips as illustrated.


WRS0448
4. Loosen the belt by holding the tongue at a right angle to the belt, then pull on the belt.


WRS0201


Unfastening the seat belts To unfasten the seat belt, press the button the buckle. SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the three-point lap- shoulder belt and fasten it, an extender is avail- able which is compatible with the installed seat belts. The extender adds approximately 8 inches (200 mm) of length and may be used for either the driver or right front passenger seating posi- tion. See a NISSAN dealer for assistance if an extender is required.


1-36 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING


c Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts.


c Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.


c Never use seat belt extenders to install child restraints. If the child restraint is not secured properly, the child could be seriously injured in a collision or a sud- den stop.


SEAT BELT MAINTENANCE c To clean the seat belt webbing, apply a mild soap solution or any solution recom- mended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry.


c If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.


CHILD RESTRAINTS


c Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt as- sembly should be replaced.


ARS1098


PRECAUTIONS ON CHILD RESTRAINTS


WARNING


c Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-37


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c Never install a rear-facing child re- straint in the front seat. An inflating supplemental front air bag could seri- ously injure or kill your child. A rear- facing child restraint must only be used in the rear seat.


c NISSAN recommends that the child re- straint be installed in the rear seat. Ac- cording to accident statistics, children are safer when properly restrained in the rear seat than in the front seat.


c An improperly installed child restraint could lead to serious injury or death in an accident.


In general, child restraints are designed to be installed with the lap portion of a three-point type seat belt. In addition, this vehicle is equipped with a universal child restraint lower anchor system, referred to as the LATCH (Lower Anchors and Tethers for CHildren) system. Some child re- straints include two rigid or webbing-mounted attachments that can be connected to these lower anchors. For details, see the (cid:147)LATCH (Lower Anchors and Tethers for CHildren) sys- tem(cid:148) later in this section.


Child restraints for infants and small children of various sizes are offered by several manufactur- ers. When selecting any child restraint, keep the following points in mind: c Choose only a restraint with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.


c Check the child restraint in your vehicle to be sure it is compatible with the vehicle(cid:146)s seat and seat belt system.


c If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child. Always follow all recommended procedures.


All U.S. states and provinces of Canada require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being oper- ated.


WRS0256


WARNING


c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


1-38 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING


c Improper use of a child restraint can increase the risk or severity of injury for both the child and other occupants of the vehicle.


c Follow all of the child restraint manu- facturer(cid:146)s instructions for installation and use. When purchasing a child re- straint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.


c If the child restraint is not anchored properly, the risk of a child being in- jured in a collision or a sudden stop greatly increases.


c Adjustable seatbacks should be posi- tioned to fit the child restraint, but as upright as possible.


c After attaching the child restraint, test it before you place the child in it. Push it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. The child restraint should not move more than 1 inch (25
mm). is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.


the restraint


If


c Failure to use the retractor(cid:146)s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.


c For a front-facing child restraint, check to make sure the shoulder belt does not go in front of the child(cid:146)s face or neck. If it does, put the shoulder belt behind the child restraint. If you must install a front facing child restraint in the front seat, see (cid:147)Installation on front passenger seat(cid:148) later in this section.


c When your child restraint is not in use, keep it secured with a seat belt to pre- vent it from being thrown around in case of a sudden stop or accident.


CAUTION


Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.


INSTALLATION ON REAR BENCH SEAT


WARNING


c The three-point seat belt in your vehicle is equipped with an automatic locking mode retractor which must be used when installing a child restraint.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-39


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


Front Facing (outboard) (cid:151) step 1


Front Facing (center) (cid:151) step 1


Front Facing (cid:151) step 2


LRS0402


LRS0401


WRS0250


Front facing When you install a child restraint on the rear bench seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing direction, de- pending on the size of the child. Adjust the head restraint to its highest position. Always follow the restraint manufacturer(cid:146)s instruc- tions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer(cid:146)s instructions for belt routing.


1-40 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


Front Facing (cid:151) step 3


Front Facing (cid:151) step 4


Front Facing (cid:151) step 5


WRS0251


WRS0146


WRS0252


3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.


4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.


5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm).


6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode.


7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-41


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is canceled.


Rear Facing (outboard) (cid:151) step 1


Rear Facing (center) (cid:151) step 1


LRS0403


LRS0404


Rear facing When you install a child restraint on the rear bench seat, follow these steps: 1. Position the child restraint on the seat. The direction of the child restraint depends on the type of the child restraint and the size of the child. Always follow the restraint manu- facturer(cid:146)s instructions.


1-42 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


Rear Facing (cid:151) step 2


Rear Facing (cid:151) step 3


Rear Facing (cid:151) step 4


LRS0408


LRS0409


LRS0410


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer(cid:146)s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emer- gency locking mode when the seat belt is fully retracted.


4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-43


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.


After the child restraint is removed and the seat belt fully retracted, the automatic locking mode (child restraint mode) is canceled.


LRS0411


Rear Facing (cid:151) step 5


5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch (25 mm).


6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the automatic locking mode.


1-44 Safety(cid:151)Seats, seat belts and supplemental air bags


LRS0429
LATCH system anchor point locations rear


bench seat


LATCH (Lower Anchors and Tethers for CHildren) SYSTEM


WARNING


c Attach LATCH system compatible child restraints only at the locations shown. If a child restraint is not secured properly, your child could be seriously injured or killed in an accident.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


LRS0395
LATCH anchor point labels rear bench seat c The LATCH system anchors are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstance are they to be used for adult seat belts or harnesses.


Some child restraints include two rigid or webbing-mounted attachments that can be con- nected to two anchors located at certain seating positions in your vehicle. This system is known as the LATCH (Lower Anchors and Tethers for CHil- dren) system. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle


seat belt to secure the child restraint. Your vehicle is equipped with special anchor points that are used with LATCH system compatible child re- straints. Check your child restraint for a label stating that it is compatible with the LATCH sys- tem. This information may also be in the child restraint owner(cid:146)s manual. If you have such a child restraint, refer to the illustration for the seating positions equipped with LATCH system anchors which can be used to secure the child restraint.


The LATCH system anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LATCH system anchors.


LATCH child restraints generally require the use of a top tether strap. See (cid:147)Top tether strap child restraint(cid:148) later in this section for installation in- structions.


When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint.


When you install a LATCH system compatible child restraint to the lower anchor attachments, follow these steps:


WARNING


Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LATCH system an- chors, such as seat belt webbing or seat cushion material. The child restraint will not be secured properly if the LATCH sys- tem anchors are obstructed.


insert


1. To install the LATCH system compatible child restraint, the child restraint LATCH system anchor attachments into the anchor points on the seat. If the child re- straint is equipped with a top tether, see (cid:147)Top tether strap child restraint(cid:148) later in this section for installation instructions.


2. After attaching the child restraint and before placing the child in it, use force to push the child restraint from side to side and tug it forward to make sure that the child restraint is securely held in place. It should not move more than 1 inch.


3. Check to make sure that the child restraint is


properly secured prior to each use.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-45


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


TOP TETHER STRAP CHILD RESTRAINT If your child restraint has a top tether strap, it must be secured to the anchor point provided behind its position.


Tighten the tether strap according to the manu- facturer(cid:146)s instructions to remove any slack. For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer(cid:146)s instructions.


WARNING


c Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


c A child restraint with a top tether should not be used in the front seat. Do not attempt to attach a tether strap to the rear tether anchor points from the front seat.


First, secure the child restraint with the seat belt or the LATCH system (rear bench seat outboard positions only), as applicable. Adjust the rear bench seat head restraint to its highest position and route the top tether strap between the head restraint and the top of the seatback. Secure the child restraint with a seat belt. Secure the top tether strap to the anchor point which provides the straightest installation of the tether strap as shown later in this section. 1-46 Safety(cid:151)Seats, seat belts and supplemental air bags


LRS0393


Anchor point locations The anchor points are located under the rear window behind the rear bench seat. If you have any questions when installing a top strap child restraint on the rear seat, consult your NISSAN dealer for details.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


LRS0392


Anchor point access


1. Pull strap 2. Anchor point location To access the anchor points behind the rear bench seat, tilt the rear seatback forward by lifting up on the pull strap behind the seat back.


1. Top tether strap 2. Hook 3. Anchor point


WRS0423


WRS0256


INSTALLATION ON FRONT PASSENGER SEAT OUTBOARD POSITION


WARNING


c Never install a rear-facing child re- straint in the front passenger seat. Supplemental front air bags inflate with great force. A rear-facing child restraint could be struck by the supplemental front air bag in a crash and could seri- ously injure or kill your child.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-47


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c The three-point seat belt in your vehicle is equipped with an automatic locking mode retractor which must be used when installing a child restraint.


c Failure to use the retractor(cid:146)s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision. Also, it can change the operation of the front pas- senger air bag. See (cid:147)Front passenger air bag and status light(cid:148) earlier in this section.


Front Facing (cid:151) step 1


WRS0379


If you must install a child restraint in the right front seat, follow these steps: 1. Position the child restraint on the front pas- senger seat. It should be placed in a front-facing direction only. Move the seat to the rearmost position. Adjust the head restraint to its highest position. Always follow the child restraint manufacturer(cid:146)s in- structions. Child restraints for infants must be used in the rear-facing direc- tion and therefore must not be used in the front seat.


WRS0378


c NISSAN recommends that child re- straints be installed in the rear seat. However, if you must install a forward- facing child restraint in the right front passenger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the pas- senger air bag is OFF. See (cid:147)Front pas- senger air bag and status light(cid:148) earlier in this section for details.


c A child restraint with a top tether strap should not be used in the front passen- ger seat.


1-48 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


Front Facing (cid:151) step 2


Front Facing (cid:151) step 3


Front Facing (cid:151) step 4


WRS0159


WRS0160


WRS0161


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer(cid:146)s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emer- gency locking mode when the seat belt is fully retracted.


4. Allow the seat belt to retract slightly. Pull up on the shoulder belt to remove any slack in the belt.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-49


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


7. Check to make sure the child restraint is properly secured prior to each use. If the seat belt locked, repeat steps 3
through 6.


is not


8. Turn the ignition to the ON position. The passenger air bag status light should say . If this light is not illu- (cid:147)OFF(cid:148) minated it may indicate a malfunction. Move the child restraint to another seating position. Have the system checked by a NISSAN dealer.


or


After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is canceled.


WRS0380


Front Facing (cid:151) step 5


5. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 inch.


6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode.


1-50 Safety(cid:151)Seats, seat belts and supplemental air bags


WRS0256
INSTALLATION ON FRONT BENCH PASSENGER SEAT CENTER POSITION


WARNING


c Never install a rear-facing child re- straint in the front passenger seat. Supplemental front air bags inflate with great force. A rear-facing child restraint could be struck by the supplemental front air bag in a crash and could seri- ously injure or kill your child.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c NISSAN recommends that child re- straints be installed in the rear seat. However, if you must install a forward facing child restraint in the front center bench seat, follow these instructions carefully.


c A child restraint with a top tether strap should not be used in the front passen- ger seat.


Front Facing (cid:151) step 1


Front Facing (cid:151) step 2


WRS0430


WRS0250


If you must install a child restraint in the front center bench seat, follow these steps: 1. Position the child restraint on the front pas- senger bench seat as illustrated. It should be placed in a front-facing direction only. Always follow the restraint manufac- turer(cid:146)s instructions. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer(cid:146)s instructions for belt routing.


Safety(cid:151)Seats, seat belts and supplemental air bags 1-51


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WRS0264


WRS0265


Front Facing (cid:151) step 3


3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.


Front Facing (cid:151) step 4


4. Before placing the child in the child restraint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely in place. It should not move more than 1 inch. If it is not secure, try to tighten the belt again, or put the restraint in another seat.


5.


6. Check to make sure the child restraint is


properly secured prior to each use.


1-52 Safety(cid:151)Seats, seat belts and supplemental air bags


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


MEMO


Safety(cid:151)Seats, seat belts and supplemental air bags 1-53


2 Instruments and controls


Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-5
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Engine oil pressure gauge . . . . . . . . . . . . . . . . . . . . . . . 2-6
Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Automatic transmission fluid temperature gauge (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7


Compass and outside temperature display (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Outside temperature display . . . . . . . . . . . . . . . . . . . . . 2-8
Compass display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Warning/indicator lights and audible reminders . . . . . . 2-12
Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
Security systems (if so equipped) . . . . . . . . . . . . . . . . . . 2-20
Vehicle security system. . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Nissan vehicle immobilizer system (NVIS) . . . . . . . . 2-21
Windshield wiper and washer switch . . . . . . . . . . . . . . . 2-22


Switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Heated mirror switch (if so equipped) . . . . . . . . . . . . . . . 2-23
Headlight and turn signal switch. . . . . . . . . . . . . . . . . . . . 2-24
Headlight control switch. . . . . . . . . . . . . . . . . . . . . . . . 2-24
Daytime running light system (Canada only) . . . . . . 2-26
Instrument brightness control . . . . . . . . . . . . . . . . . . . 2-27
Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Fog light switch (if so equipped) . . . . . . . . . . . . . . . . 2-27
Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . 2-28
Cargo lamp switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-29
Heated seat (if so equipped). . . . . . . . . . . . . . . . . . . . . . . 2-29
Vehicle dynamic control (VDC) off switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Electronic locking rear differential (E-Lock) system switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Rear sonar system off switch (if so equipped). . . . . . . . 2-31
Tow mode switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-35
Instrument panel storage trays . . . . . . . . . . . . . . . . . . 2-35
Console box (if so equipped) . . . . . . . . . . . . . . . . . . . 2-35


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/11/04—debbie X


Center armrest storage (if so equipped). . . . . . . . . . 2-37
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Sunglasses holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Seatback pocket (if so equipped) . . . . . . . . . . . . . . . 2-39
Overhead console (if so equipped) . . . . . . . . . . . . . . 2-39
Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
Grocery hooks (if so equipped) . . . . . . . . . . . . . . . . . 2-42
Lockable bedside storage compartment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-43
Power windows (if so equipped) . . . . . . . . . . . . . . . . 2-43
Manual windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Rear sliding window (if so equipped) . . . . . . . . . . . . 2-46
Sunroof (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46


Automatic sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Console light (if so equipped). . . . . . . . . . . . . . . . . . . 2-49
Personal lights (if so equipped) . . . . . . . . . . . . . . . . . . . . 2-49
Map lights (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 2-50
HomeLinkT universal transceiver (if so equipped). . . . . 2-50
Programming HomeLinkT. . . . . . . . . . . . . . . . . . . . . . . 2-51
Programming HomeLinkT for Canadian customers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
Operating the HomeLinkT universal transceiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52
Programming trouble-diagnosis . . . . . . . . . . . . . . . . . 2-52
Clearing the programmed information . . . . . . . . . . . . 2-53
Reprogramming a single HomeLinkT button . . . . . . 2-53
If your vehicle is stolen . . . . . . . . . . . . . . . . . . . . . . . . . 2-53


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/11/04—debbie X


INSTRUMENT PANEL


1.


2. 3.


4.


5.


Driver, center and passenger ventila- tors (P. 4-11) Instrument brightness control (P. 2-27) Headlight/fog light (if so equipped)/ turn signal switch (P. 2-24) Steering wheel switch for audio control (if so equipped) (P. 4-36) Driver supplemental air bag/horn (P. 1-12, P. 2-29)


6. Meters, gauges and warning/indicator


7.


lights (P. 2-3, 2-12) Cruise control main/set switches (if so equipped) (P. 5-17)


8. Windshield wiper/washer switch


2-2 Instruments and controls


(P. 2-22) Ignition switch (P. 5-7)


9. 10. Navigation system* (if so equipped)


(P. 4-2)


11. Navigation system* controls


(if so equipped) (P. 4-2)


12. Audio system controls (P. 4-19) 13. Front passenger supplemental air bag


(P. 1-12)


14. Glove box (P. 2-37) 15. Climate controls (P. 4-12) 16. Aux jack (P. 4-35) 17. Heated seat switch (if so equipped)


WIC0730


(P. 2-29)


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


18. Power outlet/Cigarette lighter (accessory) (P. 2-32/P. 2-34)


19. Vehicle dynamic control (VDC) off


switch (if so equipped) (P. 2-30)


20. Tow mode switch (P. 2-32) 21. E-Lock system switch (if so equipped)


(P .2-30)


22. Shift selector lever (console)


(if so equipped) (P. 5-9)


23. Power outlet (P. 2-32) 24. Passenger air bag status light (P. 2-18) 25. Hazard lights (P. 2-28) 26. 4WD shift switch (if so equipped)


(P. 5-20)


27. Shift selector lever (column) (if so


equipped) (P. 5-9) Instrument brightness control (P. 2-27)


28. 29. Tilt steering wheel control (P. 3-13) 30. Cargo lamp switch (P. 2-28) 31. Rear sonar system off switch


(if so equipped) (P. 2-31)


32. Pedal position adjustment switch


(if so equipped) (P. 3-13)


*: Refer to the separate Navigation System Own- er(cid:146)s Manual (if so equipped). See the page number indicated in paren- theses for operating details.


METERS AND GAUGES


1. Warning/indicator lights 2. 3. 4. 5. 6.


Tachometer Speedometer Engine coolant temperature gauge Fuel gauge Engine oil pressure gauge


LIC0540


7.


Automatic transmission fluid tempera- ture gauge (if so equipped)


8. Odometer/Twin trip odometer 9.


Voltmeter


Instruments and controls 2-3


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


LIC0541


Speedometer


1. 2. Odometer/twin trip display 3. Change button SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition key is in the ON position.


2-4 Instruments and controls


The odometer records the total distance the ve- hicle has been driven. The twin trip odometer records the distance of individual trips.


LIC0542


! Trip


! Odometer only


Changing the display: Pushing the change button changes the display as follows: Trip Resetting the trip odometer: Pushing the change button for more than 1 sec- ond resets the trip odometer to zero. Elapsed time, driving distance and average speed information is also available. Refer to the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


CAUTION


If the gauge indicates engine coolant tem- perature over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued opera- tion of the vehicle may seriously damage the engine. See (cid:147)If your vehicle over- heats(cid:148) in the (cid:147)In case of emergency(cid:148) sec- tion for immediate action required.


LIC0543


TACHOMETER The tachometer indicates engine speed in revo- lutions per minute (r/min). Do not rev engine into the red zone s1 .


CAUTION


When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage.


LIC0544
ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range s1 when the gauge needle points within the zone shown in the illustration.


The engine coolant temperature varies with the outside air temperature and driving conditions.


Instruments and controls 2-5


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


The located on the driver(cid:146)s side of the vehicle.


indicates that the fuel filler lid is


CAUTION


c If


the vehicle runs out of


fuel, malfunction indicator lamp the (MIL) may come on. Refuel as soon as possible. After a few driving trips, the lamp should turn off. If the lamp remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.


LIC0545


FUEL GAUGE The gauge indicates the approximate fuel level in the tank.


The gauge may move slightly during braking, turning, acceleration, or going up or down hills.


The gauge needle returns to E (Empty) after the ignition key is turned to OFF.


The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge regis- ters E (Empty).


2-6 Instruments and controls


c For additional information, see (cid:147)Mal- function indicator lamp (MIL)(cid:148) later in this section.


LIC0546


ENGINE OIL PRESSURE GAUGE The gauge indicates the engine lubrication sys- tem oil pressure while the engine is running. When the engine speed is high, the engine oil pressure is also high. When it is low, the gauge indicates the low oil pressure.


CAUTION


c This gauge is not designed to indicate low engine oil level. Use the dipstick to check the oil level. (See (cid:147)Engine oil(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section.)


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine.


LIC0547


VOLTMETER When the ignition key is turned to the ON posi- tion, the voltmeter indicates the battery voltage. When the engine is running, it indicates the gen- erator voltage. While cranking the engine, the volts drop below the normal range. If the needle is not in the normal range (11 - 15 volts) s1 while the engine is running, it may indicate that the charging system is not functioning properly. Have the system checked by a NISSAN dealer.


LIC0548
AUTOMATIC TRANSMISSION FLUID TEMPERATURE GAUGE (if so equipped) This gauge indicates the temperature of the au- tomatic transmission fluid. The automatic trans- mission fluid temperature is in the normal range s1 when the gauge needle points within the zone shown in the illustration.


Instruments and controls 2-7


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


COMPASS AND OUTSIDE TEMPERATURE DISPLAY (if so equipped) This unit has the following functions: c Measures terrestrial magnetism and indi-


cates heading direction of vehicle c Indicates outside air temperature


CAUTION


c This gauge is not designed to indicate low automatic transmission fluid level. Use the dipstick to check the fluid level. (See (cid:147)5-speed automatic transmission fluid(cid:148) in the (cid:147)Maintenance and do-it- yourself(cid:148) section.)


c If the gauge indicates automatic trans- mission fluid temperature over the nor- mal range, stop the vehicle as soon as safely possible. Have the vehicle checked by a NISSAN dealer. Contin- ued operation of the vehicle may seri- ously damage the transmission.


LIC0583
OUTSIDE TEMPERATURE DISPLAY Push the button when the ignition key is in the ACC or ON position. The outside tempera- ture will be displayed s1 . c To change from (cid:176)F to (cid:176)C, push and hold the button for about 3 seconds until the display begins to flash. Press the button again to toggle between (cid:176)F and (cid:176)C. Once you have selected (cid:176)F or (cid:176)C, the display will continue to flash for about 5 seconds, then the temperature will display.


2-8 Instruments and controls


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


You can also calibrate the compass by driving your vehicle on your everyday route. The com- pass will be calibrated once it has tracked three complete circles.


c When the outside temperature is between 140(cid:176)F (60(cid:176)C) and 194(cid:176)F (90(cid:176)C), the display will read 140(cid:176)F (60(cid:176)C). When the tempera- ture is above 194(cid:176)F (90(cid:176)C), the display will read (cid:147)SC(cid:148).


c When the outside temperature is between than -40(cid:176)F (-40(cid:176)C) and -60(cid:176)F (-51(cid:176)C), the display will read -40(cid:176)F (-40(cid:176)C). When the temperature is below -60(cid:176)F (-51(cid:176)C), the dis- play will read (cid:147)OC(cid:148).


c The outside temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind direc- tion and other driving conditions. The display may differ from the actual outside tempera- ture or the temperature displayed on various signs or billboards.


COMPASS DISPLAY Push the button when the ignition key is in the ACC or ON position to display the direction s1 . N: north E: east S: south W: west If the display reads (cid:147)CAL(cid:148), calibrate the compass by driving the vehicle in three complete circles at less than 5 MPH (8 km/h).


Instruments and controls 2-9


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


Zone variation change procedure The difference between magnetic north and geo- graphical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens:


1. Press and hold the


button for about 8
seconds. The current zone number will ap- pear in the display.


2. Find your current location on the zone map. Refer to the illustration. Record the zone number.


3. Press and hold the


button until the new zone number appears in the display. After you stop pressing the switch in, the display will show a compass direction within a few seconds.


Inaccurate compass direction


1. With the display turned on, push the


button about 8 seconds, until the zone se- lection comes up (a number will be dis- played in the mirror compass window).


2. Toggle until correct zone is found and re-


lease button.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


2-10 Instruments and controls


WIC0355


3. The display will return to the normal com- pass mode within 5 seconds of no button activity. If the vehicle changes zone, repeat steps 1
through 3. See map.


4.


c If the compass deviates from the correct indication soon after repeated adjustment, have the compass checked at an authorized dealer.


c The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct compass point when the ve- hicle moves to an area where the geomag- netism is stabilized.)


CAUTION


c Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet. They affect the op- eration of the compass.


c When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing.


Instruments and controls 2-11


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS


or


Anti-lock brake warning light


Low tire pressure warning light


4WD shift indicator light (


model)


Automatic transmission check warning light


Low windshield washer fluid warning light


or


Front passenger air bag status light


Automatic transmission park warning light


model)


Seat belt warning light and chime


High beam indicator light (Blue)


or


Brake warning light


Supplemental air bag warning light


Malfunction indicator lamp (MIL)


Charge warning light


Automatic transmission position indicator light


Security indicator light (NVIS) (if so equipped)


Door open warning light


Engine oil pressure low/engine coolant tem- perature high warning light


or


Active brake limited slip (if so equipped)


Cruise main switch indicator light


Slip indicator light (if so equipped)


Transfer 4LO position indicator light


model)


4WD warning light (


model)


Cruise set switch indicator light


Turn signal/hazard indicator lights


Low fuel warning light


Electronic locking rear differential (E-Lock) system on indicator light (if so equipped)


Vehicle dynamic control off indicator light (if so equipped)


CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights will come on: 2-12 Instruments and controls


or


The following lights come on briefly and then go off:


or


If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


WARNING LIGHTS


or


Anti-lock brake warning light


If the light comes on while the engine is running, it may indicate the anti-lock brake system is not functioning properly. Have the system checked by a NISSAN dealer. Turn off the engine, and start it again by slowly turning the ignition key (quickly do- ing so may cause the ABS light to stay on when there is nothing wrong). If the light stays on, have the system checked by a NISSAN dealer.


If an abnormality occurs in the system, the anti- lock function ceases, but the regular braking system continues to operate. If the light comes on while you are driving, contact a NISSAN dealer for repair.


The ABS system will be disabled and the ABS light will illuminate when the electronic locking rear differential (E-Lock) system switch (if so equipped) is turned on and the E-Lock system is engaged. If the E-Lock system disengages or the switch is turned off, the ABS system will be enabled and the ABS light will turn off.


Automatic transmission check warning light


When the ignition switch is turned ON, the light comes on for about 2 seconds. If the light blinks for approximately 8 seconds, it may indicate the automatic transmission system is not functioning properly. Have your NISSAN dealer check and repair the transmission, if necessary.


Automatic transmission park model) warning light (


WARNING


c If the ATP light is ON, this indicates that the automatic transmission P (Park) po- sition will not function and the transfer case is in neutral.


c When parking, always make sure that the 4WD shift switch is in 4H or 4LO and the parking brake is set. Failure to en- gage the transfer control in 4H or 4LO could result in the vehicle moving unex- pectedly, resulting in serious personal injury or property damage.


c Part time 4WD: Shift the 4WD switch into the 2WD, 4H or 4LO position again to turn off the ATP warning light when the automatic transmission selector le- ver is in the P position and the ATP warning light is ON. (Before shifting the 4WD switch into the 4LO position, move the automatic transmission selector le- ver into the N position once, shift the selector lever into P again and make sure the ATP warning light is OFF.)


This light indicates that the automatic transmis- sion parking function is not engaged. If the trans- fer control is not secured in any drive position while the automatic transmission selector lever is in the P (Park) position, the transmission will disengage and the drive wheels will not lock.


or


Brake warning light


This light functions for both the parking brake and the foot brake systems.


Instruments and controls 2-13


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X


When the ignition key is in the ON position, the light comes on when the parking brake is applied, and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:


1. Check the brake fluid level. Add brake fluid as necessary. See (cid:147)Brake and clutch fluid(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) sec- tion of this manual.


2.


If the brake fluid level is correct, have the brake system checked by a NISSAN dealer.


WARNING


c Your brake system may not be working properly if the warning light is on. Driv- ing could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driv- ing it could be dangerous.


c Pressing the brake pedal with the en- gine stopped and/or a low brake fluid level may increase your stopping dis- tance and braking will require greater pedal effort as well as pedal travel.


2-14 Instruments and controls


c If the brake fluid level


is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.


Charge warning light


If this light comes on while the engine is running, it may indicate the charging system is not func- tioning properly. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light remains on, see a NISSAN dealer immediately.


CAUTION


Do not continue driving if the generator belt is loose, broken or missing.


Door open warning light


This light comes on when any of the doors are not closed securely while the ignition key is in the ON position.


Engine oil pressure low/Engine coolant tempera- ture high warning light


This light warns of low engine oil pressure or high engine coolant temperature.


If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine and allow it to cool. If the light remains on after checking the oil and coolant, stop the en- gine immediately and call a NISSAN dealer or other authorized repair shop. This light is not designed to indicate a low oil or low coolant level. Check the oil level with the dipstick and check the coolant level on the reservoir. See (cid:147)Engine oil(cid:148) and (cid:147)Checking engine coolant level(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual. Also see (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emer- gency(cid:148) section of this manual.


CAUTION


c Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c If the gauge indicates engine coolant temperature over the normal range, stop the vehicle as soon as safely pos- sible. If the engine is overheated, con- tinued operation of the vehicle may se- riously damage the engine. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section for immediate ac- tion required.


4WD warning light


model)


The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started.


If the engine or vehicle is not functioning properly, the warning light will either remain illuminated or blink. See (cid:147)4WD warning light(cid:148) in the (cid:147)Starting and driving(cid:148) section.


CAUTION


c If the warning light comes on or blinks during operation, have your vehicle checked by a NISSAN dealer as soon as possible.


c Do not drive on dry hard surface roads in the 4H or 4LO position. If the 4WD warning light turns on when you are driving on dry hard surface roads: (cid:150) in the 4H position, shift the 4WD shift


switch to 2WD.


(cid:150) in the 4LO position, stop the vehicle, move the automatic transmission shift selector lever to the N position with the brake pedal depressed, and shift the 4WD shift switch to 2WD.


c If the warning light is still on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.


Low fuel warning light


This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is conve- nient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).


Low tire pressure warning light


After the ignition switch is turned ON, this light comes on for about 1 second and turns off.


This light warns of low tire pressure.


NISSAN(cid:146)s low tire pressure warning system is a tire pressure monitoring system. It monitors tire pressure of all tires except the spare. When the tire pressure monitoring system warning light is lit, one or more of your tires is significantly under- inflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle(cid:146)s tire infor- mation placard. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle(cid:146)s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the vehicle plac- ard and owner(cid:146)s manual.


The recommended inflation pressure may also be found on the Tire and Loading Information Label. Low tire pressure warning:


If the vehicle is being driven with very low tire pressure (lower than 28 psi, 193 kPa), the light will illuminate and the chime will sound for about 10 seconds. If you select the tire pressure infor- mation in the display, the FLAT TIRE warning message will be displayed.


Instruments and controls 2-15


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X


For additional information, see (cid:147)Low tire pressure warning system(cid:148) in the (cid:147)Starting and driving(cid:148) section and (cid:147)Low tire pressure warning system(cid:148) in the (cid:147)In case of emergency(cid:148) section.


WARNING


c If the light does not come on with the key switch turned ON, have the vehicle checked by a NISSAN dealer as soon as possible.


c If the light comes on while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still comes on while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, re- place it with a spare tire as soon as possible.


2-16 Instruments and controls


c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.


CAUTION


c The low tire pressure warning system is not a substitute for the regular tire pres- sure check. Be sure to check the tire pressure regularly.


c If the vehicle is being driven at speeds of less than 20 MPH (32 km/h), the low tire pressure warning system may not operate correctly.


c Be sure to install the specified size of


tires to the 4 wheels correctly.


Low windshield washer fluid warning light


This light comes on when the windshield washer fluid is at a low level. Add windshield washer fluid as necessary. See the (cid:147)Maintenance and do-it- yourself(cid:148) section of this manual.


Seat belt warning light and chime


The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver(cid:146)s seat belt is fastened. At the same time, the chime sounds for about 6 seconds unless the driver(cid:146)s seat belt is securely fastened.


Refer to (cid:147)Seat belts(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental air bags(cid:148) section for pre- cautions on seat belt usage.


Supplemental air bag warning light


When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.


the following conditions occur,


If any of the supplemental front air bags, supplemental side air bags (if so equipped), curtain side-impact and rollover air bags (if so equipped), and pre- tensioner seat belt systems need servicing and your vehicle must be taken to a NISSAN dealer: c The supplemental air bag warning light re-


mains on after approximately 7 seconds.


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


c The supplemental air bag warning light


flashes intermittently.


c The supplemental air bag warning light does


not come on at all.


Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pre- tensioner seat belts may not function properly. For additional details see (cid:147)Supplemental restraint system(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental air bags(cid:148) section of this manual.


WARNING


If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag, curtain side-impact and rollover air bag systems (if so equipped) and/or pre- tensioner seat belt systems will not oper- ate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible. INDICATOR LIGHTS


Automatic transmission posi- tion indicator light


When the ignition key is turned to the ON posi- tion, this indicator light shows the automatic


transmission selector lever position. See (cid:147)Driving the vehicle(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual. or


Active brake lim- ited slip (if so equipped)


This indicator light comes on if the active brake limited slip is activated. If activated, the system will apply brake to the slipping rear wheel, giving the non-slipping rear wheel more traction.


Cruise main switch indicator light


The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.


Cruise set switch indicator light


The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning prop- erly. Have the system checked by a NISSAN dealer.


Electronic locking rear differ- ential (E-Lock) system on in- dicator light (if so equipped)


This light comes on when the electronic locking rear differential (E-Lock) system clutch is fully engaged.


The indicator light flashes when the system is first turned on. When the system fully engages, the light remains on. If the switch is on and the indicator light continues to flash, the system is not engaged.


For additional information, see (cid:147)Electronic lock- ing rear differential (E-Lock) system switch(cid:148) later in this section and (cid:147)Electronic locking rear differ- ential (E-Lock) system(cid:148) in the (cid:147)Starting and driv- ing(cid:148) section of this manual.


4WD shift indicator light


model)


The light should turn off within 1 second after turning the ignition switch to ON. While the engine is running, the 4WD shift indi- cator light will illuminate the position selected by the 4WD shift switch. The 4WD shift indicator light may blink while shifting from one drive mode to the other.


Instruments and controls 2-17


Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/09/04—debbie X


or


Front passenger air bag status light


Loading...
x