2004 Nissan Titan Owners Manual

LDI0410

WHEELS AND TIRES

If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label under the 9Recommended Cold Tire Inflation Pressure9 heading. The Tire and Loading Infor- mation label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. Incorrect tire pressure, including under in- flation, may adversely affect tire life and vehicle handling.

Maintenance and do-it-yourself 8-29

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WARNING

c Improperly inflated tires can fail sud-

denly and cause an accident.

c The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components.

c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

c Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85
MPH (137 km/h) may result in tire failure, loss of control and possible injury.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

8-30 Maintenance and do-it-yourself

Tire and loading information label (for US) s1 Seating capacity: The maximum number of occupants that should be seated in the ve- hicle.

s2 Vehicle load limit: See loading information in information

the Technical and consumer section.

s3 Original tire size: The size of the tires origi- nally installed on the vehicle at the factory.

LDI0392
s4 Recommended cold tire inflation pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best balance of tire wear and vehicle handling characteristics based on the vehicles GVWR.

s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later in this

s6

section. and s7 Spare tire size or compact spare tire size (if so equipped).

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.

6. 7. Check the pressure of all other tires, includ-

ing the spare.

Front Original Tire

Rear Original Tire

Spare Tire

Size

P245/75R17
P285/70R17
P265/70R18
P245/75R17
P285/70R17
P265/70R18
P245/75R17
P285/70R17
P265/70R18

Cold Tire Infla- tion Pressure 240 kPa, 35 PSI

240 kPa, 35 PSI

240 kPa, 35 PSI

LDI0393

Checking tire pressure 1. Remove the valve stem cap from the tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leakage.

3. Remove the gauge.

4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label.

WDI0394

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

Maintenance and do-it-yourself 8-31

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WDI0395
6. Two- or three-digit number: This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. Tire speed rating. You should not drive the

vehicle faster than the tire speed rating.

s1 Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is designed for

passenger vehicles.

2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.

3. Two-digit number: This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width.

4. R: The 9R9 stands for radial. 5. Two-digit number: This number is the wheel

or rim diameter in inches.

8-32 Maintenance and do-it-yourself

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

s2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Number.

2. Two-digit code: Manufacturer(cid:146)s identifica-

tion mark

3. Two-digit code: Tire size

4. Three-digit code: Tire type code (Optional)

5. Three-digit code: Date of Manufacture

WDI0396
6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.

s3 Tire ply composition and material The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. s4 Maximum permissible inflation pressure This number is the greatest amount of air pres- sure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.

s5 Maximum load rating This number indicates the maximum load in kilo- grams and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire. s6 Term of (cid:148)tubeless(cid:148) or (cid:148)tube type(cid:148) Indicates whether the tire requires an inner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). s7 The word (cid:148)radial(cid:148) The word 9radial9 is shown if the tire has radial structure. s8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout Intended Outboard Sidewall is (1) the sidewall that contains a white- wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the outward facing sidewall of an asymmetrical tire that has a par- ticular side that must always face outward when mounted on a vehicle.

this section,

Maintenance and do-it-yourself 8-33

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

TYPES OF TIRES

WARNING

c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.

c Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ- ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. 8-34 Maintenance and do-it-yourself

Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.

If you do not,

If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing

studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use only SAE class (cid:147)S(cid:148) chains. Class 9S9 chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class (cid:147)S(cid:148) chains are de- signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufac- turer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully load- ing your vehicle when using tire chains. In addi- tion, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

Tire chains must be installed only on the rear wheels and not on the front wheels. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. Use only the 2WD range when driving on clear paved roads.

The wheel nuts must be kept tightened to specifications at all times. It is recom- mended that wheel nuts be tightened to specification at each tire rotation interval.

WARNING

c After rotating the tires, check and ad-

just the tire pressure.

c Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

c Do not include the spare tire in the tire

rotation.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

WDI0258

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km).

See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section in this manual for tire replacing proce- dures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque: 98 ft-lb (133 N•m)

Maintenance and do-it-yourself 8-35

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

c The original tires have built-in tread wear indicators. When the wear indica- tors are visible, the tire(s) should be replaced.

c Improper service of the spare tire may result in serious personal injury. If it is necessary to repair the spare tire, con- tact a NISSAN dealer.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

WDI0259

1. Wear indicator 2. Location mark Tire wear and damage

WARNING

c Tires should be periodically inspected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.

8-36 Maintenance and do-it-yourself

WARNING

c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.

c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.

this manual

with

the

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. is not

retread tires

c The use of recommended. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.

c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .

Care of wheels c Wash the wheels when washing the vehicle

to maintain their appearance.

c Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

c Do not use abrasive cleaners when washing

the wheels.

c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

Maintenance and do-it-yourself 8-37

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

MEMO

8-38 Maintenance and do-it-yourself

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation . . . . . . . . . . . 9-4
Recommended SAE viscosity number . . . . . . . . . . . . 9-5
Air conditioner system refrigerant and lubricant recommendations . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8

When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification number (VIN) plate . . . . . . . . . . 9-9
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
F.M.V.S.S. certification label . . . . . . . . . . . . . . . . . . . . 9-10
Emission control information label . . . . . . . . . . . . . . . 9-10
Tire and loading information label. . . . . . . . . . . . . . . . 9-11
Air conditioner specification label. . . . . . . . . . . . . . . . 9-11
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12

Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Securing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Utili-track(cid:153) channel system (if so equipped) . . . . . . 9-14
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Truck-camper loading information . . . . . . . . . . . . . . . . . . 9-19
Crew Cab Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
King Cab models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Special Body vehicles. . . . . . . . . . . . . . . . . . . . . . . . . . 9-19
Location for center of gravity . . . . . . . . . . . . . . . . . . . . 9-20
Payload weight capacity. . . . . . . . . . . . . . . . . . . . . . . . 9-20
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . 9-21
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Towing load/specification chart . . . . . . . . . . . . . . . . . 9-24
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-32
Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-32
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-32
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-33
Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-33
Readiness for inspection/maintenance (I/M) test . . . . . 9-34
Event data recorders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-34
Owner(cid:146)s Manual/Service Manual order information . . . 9-35
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-36

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/11/04—debbie X

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the (cid:147)Maintenance and do-it-yourself(cid:148) section to determine the proper refill capacity.

Fuel Engine oil *7

Drain and Refill

Capacity (Approximate) US measure 28 gal

Imp measure 23-1/4 gal

With oil filter change

Without oil filter change

6-1/2 qt

6-1/4 qt

5-1/2 qt

5-1/4 qt

Cooling system

With reservoir

12-7/8 qt

10-3/4 qt

Liter 105.8

6.2

5.9

12.2

Automatic transmission fluid Power steering fluid (PSF) Brake fluid

Multi-purpose grease Air conditioning system refrigerant Air conditioning system lubricants Transfer fluid

Refill to the proper level according to the instructions in the (cid:147)Main- tenance and do-it-yourself(cid:148) section.

(cid:151) (cid:151) (cid:151) 2-1/8 qt

(cid:151) (cid:151) (cid:151) 1- 3/4 qt

(cid:151) (cid:151) (cid:151) 2.0

Recommended Fluids and Lubricants

Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1

(cid:149) API Certification Mark *2 *3
(cid:149) API grade SL, Energy Conserving *2 *3
(cid:149) ILSAC grade GF-III*2 *3

50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine Nissan Matic J ATF *4
Genuine NISSAN PSF or equivalent.*8
Genuine NISSAN Super Heavy Duty Brake Fluid*5 or equivalent DOT 3 (US FMVSS No. 116) NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a)*6
NISSAN A/C System Lubricant Type S (DH-PS) or equivalent*6
Genuine Nissan Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid*8
API GL-5 Viscosity SAE 80W-90*9
API GL-5 Viscosity SAE 80W-90*9
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent

2-7/8pt 3-1/2 pt 1 gal

3-3/8 pt 4-1/4 pt 1-1/4 gal

Front final drive oil Rear final drive oil Windshield washer fluid (shared between front and rear wipers) *1: For further details, see (cid:147)Fuel recommendation.(cid:148) *2: For further details, see (cid:147)Engine oil and oil filter recommendations.(cid:148) *3: For further details, see (cid:147)Recommended SAE engine oil viscosity.(cid:148) *4: Using automatic transmission fluid other than Genuine Nissan Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle warranty. *5: Available in mainland USA through your NISSAN dealer. *6: For further details, see (cid:147)Air conditioner specification label.(cid:148) *7: For further details, see (cid:147)Changing engine oil.(cid:148) *8: For Canada, NISSAN Automatic Transmission Fluid (ATF), DEXRON(cid:153) III/MERCON(cid:153), or equivalent ATF may also be used. *9: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 0(cid:176) C (32(cid:176) F).

1.6
2.01
4.5

9-2 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).

CAUTION

c Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

c Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.

Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter specifications where it is available. Many of the automobile manufacturers developed this specification to improve emission system and vehicle perfor- mance. Ask your service station manager if the gasoline meets the World-Wide Fuel Charter specifications. Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN

supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager. If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

c If an oxygenate-blend other

c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount

of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.

fuels,

oxygenate-blend

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine.

Technical and consumer information 9-3

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy (cid:147)spark knock.(cid:148) ((cid:147)Spark knock(cid:148) is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

ignition timing may result

9-4 Technical and consumer information

ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the cor- rect quality and viscosity to ensure satisfactory engine life and performance. NISSAN recom- mends the use of a low friction oil (energy con- serving oil) in order to improve fuel economy and conserve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage.

Only those engine oils with the American Petro- leum Institute (API) CERTIFICATION MARK on

WTI0082
the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories.

If you cannot find engine oil with the API CERTI- FICATION MARK, use API grade SL Energy Conserving oil. An oil with a single designation SL, or in combination with other categories (for example, SL/CF) may also be used if one with the API CERTIFICATION MARK cannot be found. An ILSAC grade GF-III oil can also be used.

NISSAN recommends mineral based oils. These oils must, however, meet the API quality and SAE viscosity ratings specified for your vehicle.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. The chart (cid:147)Rec- ommended SAE viscosity number(cid:148) shows the recommended oil viscosities for the expected ambient temperatures. Choosing an oil viscosity other than that recommended could cause seri- ous engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in (cid:147)Change intervals(cid:148).

Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle warranty. Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: c repeated short distance driving at cold out-

side temperatures

c driving in dusty conditions c extensive idling c towing a trailer

ATI1028

RECOMMENDED SAE VISCOSITY NUMBER c SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0(cid:176)F (-18(cid:176)C). Technical and consumer information 9-5

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the lubricant, NISSAN A/C system oil DH-PS or the exact equivalents.

CAUTION

The use of any other refrigerant or lubri- cant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner system components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth(cid:146)s ozone layer. Although this refrigerant does not affect the earth(cid:146)s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.

9-6 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

SPECIFICATIONS

ENGINE

Model

Type Cylinder arrangement Bore x Stroke Displacement Firing order

Idle speed

A/T (in (cid:147)N(cid:148) position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle

Spark plug

Spark plug gap (Nominal)

Camshaft operation

VK56DE

Gasoline, 4-cycle, DOHC 8-cylinder, V-block, Slanted at 90(cid:176)

in (mm) 3.858 x 3.622 (98 x 92)

cu in (cm3) 338.78 (5,552)

1(cid:150)8(cid:150)7(cid:150)3(cid:150)6(cid:150)5(cid:150)4(cid:150)2

See the (cid:147)Emission Control label(cid:148) on the underside of the hood.

Standard PLFR5A-11

Hot PLFR4A-11
Cold PLFR6A-11

in (mm) 0.043 (1.1)

Timing chain

The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Technical and consumer information 9-7

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Wheels

Tires

Spare tire

17 x 7.5J 18 x 8.0J

P245/75R17
P285/70R17
P265/70R18
Full size

Overall length Overall width Overall height

2wd KC 4wd KC 2wd CC 4wd KC Front tread Rear tread Wheelbase

Gross vehicle weight rating Gross axle weight rating

Front Rear

in (mm) 224.2 (5,695) in (mm) 78.8 (2,001)

76.0(1,905.1) in (mm) 76.6(1,945.8) in (mm) 75.1 (1,907) in (mm) 76.7 (1,948) in (mm) 67.5 (1,715) in (mm) in (mm) 67.5 (1,715) in (mm) 139.8 (3,550) lb (kg) See the (cid:147)F.M.V.S.S.

certification label(cid:148) on the center pillar between the driver(cid:146)s side front and side doors.

lb (kg) lb (kg)

9-8 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle(cid:146)s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

VEHICLE IDENTIFICATION

LTI0085
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

LTI0086
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.

Technical and consumer information 9-9

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WTI0095

WTI0099

LTI0087

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

F.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Standard (F.M- .V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Num- ber (VIN), etc. Review it carefully.

EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.

information label

is at-

9-10 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

INSTALLING FRONT LICENSE PLATE

WTI0100
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown.

WTI0101
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed as shown.

LTI0093

Use the following steps to mount the front license plate: s1 Make holes on the plastic finisher at the location mark (small dimple) using a 0.20 in (5 mm) drill. Apply light pressure to the drill. Install the license plate holder using the two screws provided with the holder.

s2 Mount the license plate using two M6-

14mm bolts. License plate bolt tightening torque:

3.8 - 4.7 ft-lb (5.10 - 6.37 N•m)

Technical and consumer information 9-11

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

VEHICLE LOAD CAPACITY Do not exceed the load limit of your vehicle shown as 9The combined weight of occupants and cargo9 on the Tire and Loading Information label. Do not exceed the number of occupants shown as 9Seating Capacity9 on Tire and Loading Information label. To get 9the combined weight of occupants and cargo9, add the weight of all occupants, then add the total luggage weight. Examples are shown below.

VEHICLE LOADING INFORMATION

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

TERMS It is important to familiarize yourself with the fol- lowing terms before loading your vehicle: c Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and op- tional equipment, fluids, emergency tools, and spare tire assembly. This weight does not include passengers and cargo.

c GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

c GVWR (Gross Vehicle Weight Rating) - maximum total combined weight of the un- loaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional

9-12 Technical and consumer information

equipment. This information is located on the F.M.V.S.S. label.

c GAWR (Gross Axle Weight Rating) - maxi- mum weight (load) limit specified for the front or rear axle. This information is located on the F.M.V.S.S. label.

c GCWR (Gross Combined Weight rating) - The maximum total weight rating of the ve- hicle, passengers, cargo, and trailer.

c Vehicle Capacity Weight, Load limit, Total load capacity - maximum total weight limit specified of the load (passengers and cargo) for the vehicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be included as part of the cargo load. This information is located on the Tire and Loading Information label.

c Cargo capacity - permissible weight of cargo, the subtracted weight of occupants from the load limit.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

6.

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Before driving a loaded vehicle, confirm the you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See (cid:147)Measurement of Weights(cid:148) later in this section. Also check tires for proper inflation pressures. See the Tire and Loading label.

Steps for determining correct load limit 1. Locate the statement (cid:147)The combined weight of occupants and cargo should never ex- ceed XXX pounds(cid:148) on your vehicle(cid:146)s tire placard.

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.

WTI0091
4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400
lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400-750 (5 * 150) = 650 lbs.)

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

Technical and consumer information 9-13

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

LTI0102

SECURING THE LOAD For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box.

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.

9-14 Technical and consumer information

c Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

LTI0107

Side channels

1. 2. Header channel 3. Channel sections 4. UTILI-TRACK(cid:153) CHANNEL SYSTEM (if so equipped)

Floor channels

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WARNING

c Properly install and tighten the tie- down cleats into the Utili-track(cid:153) chan- nel system. Failure to properly install the tie-down cleats can cause the cargo to become unsecured. In a sudden stop or collision, unsecured cargo could cause personal injury.

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

The Utili-track(cid:153) channel system allows you to move tie-down clamps in the bed to the best location to secure a load.

The tie-down cleats must be installed so the clamp is properly seated in the notches in the rail. If the tie-down cleat is not seated in the notches, it will not be flush with the rail and cannot be properly tightened. The bolt in the center of the cleat must be tightened hand tight (20 (cid:150) 40 inch pounds)

Check the tightness of the tie-down cleat peri- odically during a trip to make sure the center bolt has not become loose.

Install the tie-down cleat as follows:

1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors.

2. Loosen the center bolt completely.

3.

LTI0103
Insert the cleat into the channel perpendicu- lar to the channel as shown. Then rotate the cleat clockwise 90(cid:176) and slide it to the de- sired location.

Technical and consumer information 9-15

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

5. There should be no gap between the bottom of the cleat and the top of the channel. Tighten the center bolt hand tight (20-40
inch pounds).

WTI0124

LTI0104
4. Position the cleat so the nubs on the bottom

fully seat into the channel detents.

9-16 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

CAUTION

c Install only one cleat per section of

channel.

c Applying loads at angles to the cleats greater then 45(cid:176) or loads greater than 150 lbs. (header and floor channels) or 200 lbs. (side channels) may cause damage to the channel or bed.

LTI0106

Technical and consumer information 9-17

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

1 correct installation, 2 incorrect installation

WARNING

Do not install accessories over the gap between the front and rear side channels. Doing this could affect the rear structure in certain rear impacts, which could result in serious injury.

9-18 Technical and consumer information

LTI0123

WTI0119

CAUTION

Properly secure all cargo with ropes or straps to prevent it from sliding or shifting. Use the channel end stoppers to help se- cure items in the channels from sliding off the end of the truck bed.

Channel End Stoppers The channel end stoppers should be used to help prevent accessories installed in the channels from sliding or shifting off the end of the truck bed. They must be installed so they are properly seated in the detents in the channel.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

Install the channels end stoppers as follows:

1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors.

2. Loosen the bolt on the center of the end stopper with the provided wrench and insert it into the channel.

3. Position the end stopper to the desired lo- cation on the channel so the nubs on the bottom of the end stopper fully seat into the channel detents.

4. Tighten the bolt on the center of the end

stopper with the provided wrench.

LOADING TIPS c The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S. certi- fication label.

c Do not load the front and rear axle to the

GAWR. Doing so will exceed the GVWR.

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.

c Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

c Overloading not only can shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and longer braking distances. This may cause a premature tire failure which could result in a serious accident and personal injury. Failures caused by overloading are not covered by the ve- hicle(cid:146)s warranty.

TRUCK-CAMPER LOADING INFORMATION

CREW CAB MODELS Crew Cab models should not be used to carry a slide-in camper. KING CAB MODELS This information is provided for you to properly install a slide-in camper and is based on the National Highway Traffic Safety Administration regulations. It is recommended that, before in- stalling the camper, you carefully read the follow- ing information and ensure that the camper meets the specifications. This information may not apply to some Canada model vehicles. SPECIAL BODY VEHICLES Some vehicles are equipped with commercial or camper bodies. However, this Owner(cid:146)s Manual does not cover these options. For further infor- mation, please refer to the body manufacturer(cid:146)s instruction manual.

Technical and consumer information 9-19

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

WARNING

Overloading or improper loading can ad- versely affect vehicle handling, braking and performance and may lead to accidents.

PAYLOAD WEIGHT CAPACITY The vehicle payload weight capacity shown on following charts indicate the maximum total weight of passengers, optional equipment (air conditioning, trailer hitch, etc) and cargo that your vehicle is designed to carry.

Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See (cid:146)(cid:146)Vehicle Loading Information(cid:146)(cid:146) earlier in this section for details.

Also check tires for proper inflation pressures. See the Tire and Loading Information label.

ATI0703

LOCATION FOR CENTER OF GRAVITY The illustration indicates the recommended cargo center of gravity location zone. King Cab: L1 = 960.1 mm (37.8 in), L2 = 1,087.1 mm (42.8
in)

WARNING

Improper loading may be dangerous. If a load is too far back, it can affect handling characteristics. If a load is too far forward, the front axle may be overloaded.

ATI0705
When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the camper manufacturer(cid:146)s weight figure, plus: c the weight of installed additional camper included in the camper

equipment not manufacturer(cid:146)s weight figure, c the weight of camper cargo, c and the weight of occupants in the camper. The total cargo load should not exceed the truck(cid:146)s pay load weight rating and the camper(cid:146)s center of gravity should fall within the truck(cid:146)s recommended center of gravity location zone when installed.

9-20 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

2WD

4WD

KC

CC

KC

CC

Payload Weight Capacity

Standard bed XE SE

High utility bed SE LE

Standard bed XE SE

High utility bed SE LE

Standard bed XE SE

High utility bed SE LE

Standard bed XE SE

High utility bed SE LE

Federal

1618 lb. (734 kg)

1570 lb. (712 kg)

1488 lb. (675kg)

1374 lb. (623 kg)

1563 lb. (709 kg)

1521 lb. (690kg)

1438 lb. (652 kg)

1314 lb. (596 kg)

1488 lb. (675 kg)

1438 lb. (652 kg)

1356 lb. (615 kg)

1241 lb. (563 kg)

1431 lb. (649 kg)

1391 lb. (631 kg)

1308 lb. (593 kg)

1184
lb. (537

Canada 1614 lb. (732 kg)

NA

1484lb. (673 kg)

1369 lb. (621 kg)

1559 lb. (707 kg)

NA

1433 lb. (650 kg)

1310 lb. (594 kg)

1484 lb. (673 kg)

NA

1352 lb. (613 kg)

1237 lb. (561 kg)

1424 lb. (646 kg)

NA

1299 lb. (589 kg)

kg) 1180

lb.

(535kg)

MEASUREMENT OF WEIGHTS Secure loose items to prevent weight shifts that could affect the balance of your vehicle. When the vehicle is loaded, drive to a scale and weigh the front and the rear wheels separately to deter- mine axle loads. Individual axle loads should not exceed either of the gross axle weight ratings (GAWR). The total of the axle loads should not exceed the gross vehicle weight rating (GVWR). These ratings are given on the vehicle certifica- tion label. If weight ratings are exceeded, move or remove items to bring all weights below the rat- ings.

Technical and consumer information 9-21

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

TOWING A TRAILER

WARNING

Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents.

CAUTION

c Do not tow a trailer or haul a heavy load for the first 500 miles (800 km). Your engine, axle or other parts could be damaged.

c For the first 500 miles (800 km) that you tow a trailer, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of your vehicle wear in at the heavier loads.

Your new vehicle was designed to be used pri- marily to carry passengers and cargo. Remember that towing a trailer places additional loads on your vehicle(cid:146)s engine, drive train, steering, brak- ing and other systems. A Nissan Trailer Towing Guide (U.S. only) is available from a NISSAN dealer. This guide in- cludes information on trailer towing ability and the special equipment required for proper towing.

9-22 Technical and consumer information

specified in

MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value following Towing Load/Specification Chart found later in this sec- tion. The total trailer load equals trailer weight plus its cargo weight. c When towing a trailer load of 1,000 lbs. (454 kg) or more, trailers with a brake sys- tem MUST be used.

the

The maximum GCWR (Gross Combined Weight Rating) should not exceed the value specified in the following Towing Load/ Specification Chart.

The GCWR equals the combined weight of the towing vehicle (including passengers and cargo) plus the total trailer load. Towing loads greater than these or using improper towing equipment could adversely affect vehicle handling, braking and performance. The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads, but also the places you plan to tow. Tow weights appro- priate for level highway driving may have to be reduced on very steep grades or in low traction situations (for example, on slippery boat ramps). Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside

temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.

WARNING

Overheating can result in reduced engine power and vehicle speed. The reduced speed may be lower than other traffic, which could increase the chance of a col- lision. Be especially careful when driving. Pull to the side of the road to a safe area. Allow the engine to cool and return to normal operation. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

CAUTION

Vehicle damage resulting from improper towing procedures are not covered by NISSAN warranties. A NISSAN Trailer Towing Guide (U.S. only) containing infor- mation on trailer towing ability and the special equipment required may be ob- tained from a NISSAN dealer.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

CA0009

CA0036

Tongue load When using a weight carrying or a weight distrib- uting hitch, keep the tongue load between 10 - 15 percent of the total trailer load within the maximum tongue load limits shown in the follow- ing Towing Load/Specification Chart. the tongue load becomes excessive, rearrange cargo to allow for proper tongue load.

If

Maximum gross vehicle weight/maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating (GVWR) shown on the F. M. V. S. S. certification label. The gross vehicle weight equals the com- bined weight of the unloaded vehicle, passen- gers, luggage, hitch, trailer tongue load and any other optional equipment. In addition, front or rear gross axle weight must not exceed the gross axle weight rating (GAWR) shown on the F. M. V. S. S. certification label.

Technical and consumer information 9-23

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

TOWING LOAD/SPECIFICATION CHART

Towing

Capacity*1, *3

Tongue Load

*3

Gross Com- bined Weight

Rating

w/o tow package

with tow package*2

w/o tow package with tow package*2

w/o tow package with tow package*2

XE

SE w/standard bed

SE w/High Utility Bed

LE w/High Utility Bed

6,500 lb. (2,948 kg)

7,400 lb. (3,357 kg)

7,300 lb. (3,311 kg)

7,200 lb. (3,266 kg)

N/A

9400 lb. (4,264 kg)

9,500 lb. (4,309 kg) 2WD

K/Cab

9,300 lb. (4,218 kg)

9,200 lb. (4,173 kg)

650 lb. (295 kg)

740 lb. (336 kg)

730 lb. (331 kg)

720 lb. (327 kg)

N/A

2WD 11,600 lb.

(5,262 kg)

4WD 11,800 lb.

(5,352 kg)

N/A

N/A

940 lb. (426 kg) 950 lb. (430 kg) 2WD K/Cab

2WD 12,800 lb.

(5,806 kg)

14,600 lb.

(6,622 kg)

4WD 13,000 lb.

(5,896 kg)

14,800 lb.

(6,713 kg)

930 lb. (422 kg)

920 lb. (417 kg)

2WD 12,800 lb.

(5,806 kg)

14,600 lb.

(6,622 kg)

4WD 13,000 lb.

(5,896 kg)

14,800 lb.

(6,713 kg)

2WD 12,800 lb.

(5,806 kg)

14,600 lb.

(6,622 kg)

4WD 13,000 lb.

(5,896 kg)

14,800 lb.

(6,713 kg)

*1: The towing capacity values are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment will add weight to the vehicle and reduce your vehicle(cid:146)s maximum towing capacity. *2: Requires weight distribution hitch. *3: The maximum towing capacity when using the genuine NISSAN step bumper as a ball mount is 5,000 lb. (2,268 kg) and 500 lb. (227 kg) tongue load.

9-24 Technical and consumer information

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

TOWING SAFETY Trailer hitch Your vehicle may be equipped with an optional trailer tow package. The trailer tow package in- cludes a receiver-type frame mounted hitch. This hitch is rated for the maximum towing capacity of this vehicle when the proper towing equipment is used. Choose a proper ball mount and hitch ball that is rated for the trailer to be towed. Genuine Nissan ball mounts and hitch balls are available from your NISSAN dealer.

If your vehicle is not equipped with the optional trailer tow package, check the towing capacity of your bumper hitch or receiver-type frame mounted hitch. Choose a proper hitch for your vehicle and trailer. A genuine Nissan trailer hitch is available from your NISSAN dealer. Make sure the trailer hitch is securely attached to the vehicle to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks.

WARNING

c Trailer hitch components have specific weight ratings. Your vehicle may be ca- pable of towing a trailer heavier than the weight rating of the hitch compo- nents. Never exceed the weight rating of the hitch components. Doing so can cause serious personal injury or prop- erty damage

Hitch ball Choose a hitch ball of the proper size and weight rating for your trailer: c The required hitch ball size is stamped on most trailer couplers. Most hitch balls also have the size printed on the top of the ball. c Choose the proper class hitch ball based on

the trailer weight.

c The diameter of the threaded shank of the hitch ball must be matched to the ball mount hole diameter. The hitch ball shank should be no more than 1/16(cid:148) smaller than the hole in the ball mount.

c The threaded shank of the hitch ball must be long enough to be properly secured to the ball mount. There should be at least 2
threads showing beyond the lock washer and nut.

Ball mount The hitch ball is attached to the ball mount and the ball mount is inserted into the hitch receiver. Choose a proper class ball mount based on the trailer weight. Additionally, the ball mount should be chosen to keep the trailer tongue level with the ground. Weight carrying hitches A weight carrying or 9dead weight9 ball mount is one that is designed to carry the whole amount of tongue weight and gross weight directly on the ball mount and on the receiver. Weight distribution hitch This type of hitch is also called a (cid:147)load-leveling(cid:148) or (cid:147)equalizing(cid:148) hitch. A set of bars attach to the ball mount and to the trailer to distribute the tongue weight (hitch weight) of your trailer. Many ve- hicles can(cid:146)t carry the full tongue weight of a given trailer, and need some of the tongue weight transferred through the frame and pushing down on the front wheels. This gives stability to the tow vehicle. Another reason to have a weight distributing ball mount is to comply with the rating on your re- ceiver. Most receivers have a weight carrying rating of 5,000 lbs. gross weight, 500 lbs. tongue weight and a weight distribution rating of 10,000
Technical and consumer information 9-25

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

lbs. gross weight, 1,000 lbs. tongue weight. This means that without using a weight distributing ballmount, the receiver is only designed to carry 5,000 lbs.

When hooking up a trailer using a weight distrib- uting hitch, always refer to the hitch manufactur- er(cid:146)s instructions.

1. Park unloaded vehicle on a level surface. With the ignition on and the doors closed, allow the vehicle to stand for several minutes so that it can level.

2. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle.

3. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0 - .5 inches (0 (cid:150) 13 mm) of the reference height measured in step 2. The rear bumper should be no higher than the reference height measured in step 2.

WARNING

Properly adjust the weight distributing hitch so the rear of the bumper is no higher than the measured reference height when the trailer is attached. If the rear bumper is higher than the measured reference height when loaded, the vehicle may handle unpredictably which could cause a loss of vehicle control and cause serious personal injury or property damage.

Sway control device Sway control devices are used to help control the effects of sudden maneuvers, wind gusts, and buffeting caused by other vehicles. Make sure the sway control device is compatible with the trail- er(cid:146)s brake system. Class I hitch Class I trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 2,000 lb (909 kg). Class II hitch Class II trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 3,500 lb (1,510 kg).

9-26 Technical and consumer information

Class III hitch Class III trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 5,000 lb (2,272 kg).

The genuine NISSAN step bumper is considered a Class III ball mount. Class IV hitch Class IV trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 10,000 lb (4,545 kg). A weight distributing hitch should be used to tow trailers that weigh over 5,000 lb (2,272 kg). Your vehicle may be equipped with Class IV trailer hitch equipment that has a 10,000 lb (4,545 kg) maximum weight rating, but your ve- hicle is only capable of towing the maximum trailer weights Towing Load/Specification Chart earlier in this section.

shown

the

in

CAUTION

c Special hitches which include frame re- inforcements are required for towing above 2,000 lb (907 kg). Suitable genu- ine NISSAN hitches, ball mounts and hitch balls for pickup trucks and sport utility vehicles are available at a NISSAN dealer.

Z REVIEW COPY—2004 Titan (tzw) Owners Manual (owners)—USA_English (nna) 06/10/04—debbie X

c The hitch should not be attached to or the impact-

the operation of

affect absorbing bumper.

c Do not use axle-mounted hitches. c Do not modify the vehicle exhaust sys- tem, brake system, etc. to install a trailer hitch.

c To reduce the possibility of additional damage if your vehicle is struck from the rear, where practical, remove the hitch and/or receiver when not in use. c After the hitch is removed, seal the bolt holes to prevent exhaust fumes, water or dust from entering the passenger compartment.

c Regularly check that all trailer hitch mounting bolts are securely mounted. c When towing with the hitch ball mounted to the rear bumper, do not make sharp turns. The trailer may con- tact the bumper and cause damage to the bumper or trailer.

Tire pressures c When towing a trailer, inflate the vehicle tires to the recommended cold tire pressure indi- cated on the Tire and Loading Information label.

c Trailer tire condition, size,

load rating and proper inflation pressure should be in accor- dance with the trailer and tire manufacturer(cid:146)s specifications.

Safety chains Always use suitable safety chains between your vehicle and the trailer. The safety chains should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. The safety chains can be attached to the bumper if the hitch ball is mounted to the bumper. Be sure to leave enough slack in the chains to permit turning corners.

Trailer lights

CAUTION

When splicing into the vehicle electrical system, a commercially available power- type module/converter must be used to provide power for all trailer lighting. This unit uses the vehicle battery as a direct