2002 Nissan Sentra Owners Manual

WARNING

c Never get under the vehicle while it

is supported only by the jack.

c Use only the jack provided with your vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change.

c Use the correct

jack-up points. Never use any other part of the ve- hicle for jack support.

In case of emergency 6-5

Z X

c Never jack up the vehicle more than

necessary.

c Never use blocks on or under the

jack.

c Do not start or run engine while vehicle is on the jack. It may cause the vehicle to move.

c Do not allow passengers to stay in

the vehicle while it is on the jack.

6-6 In case of emergency

SCE0002

c Never run the engine with a wheel off the ground. It may cause the vehicle to move.

Carefully read the caution label attached to the jack body and the following in- structions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.

2. Place the jack directly under the jack-up

point as illustrated above so the top of the jack contacts the vehicle at the jack-up point. Align the center of the jack head with the notch at the jack-up point, as shown. Also fit the notched portion of the vehicle in the groove of the jack head, as shown. The jack should be used on firm and level ground.

3. To lift the vehicle, securely hold the jack lever and rod with both hands as shown. Carefully raise the vehicle until the tire clears the ground. Remove the wheel nuts, and then remove the tire.

Z X

WCE0007

Installing the spare tire The TEMPORARY USE ONLY spare tire is designed for emergency use. See spe- cific instructions under the heading ‘‘Wheels and tires’’ in the ‘‘Maintenance and do-it- yourself’’ section of this own- er’s manual. 1. Clean any mud or dirt from the surface

between the wheel and hub.

2. Carefully put the spare tire on and tighten

the wheel nuts finger tight.

3. With the wheel nut wrench, tighten wheel

nuts alternately and evenly until they are tight.

4. Lower the vehicle slowly until

the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts se- curely in the sequence as illustrated. Lower the vehicle completely.

WARNING

c Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.

c Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.

c Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of flat tire, etc.).

As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque:

80 ft-lb (108 Nzm)

The wheel nuts must be kept tightened to specifications at all times. It is recom- mended that wheel nuts be tightened to specification at each lubrication interval. Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire placard affixed to the driver’s door center pillar. 5. With the spare tire installed on the vehicle, place the damaged tire in the spare tire storage area. Put the jack rod and wheel nut wrench in the tool bag and place the tool bag in the spare tire storage area.

6. Place the spare tire cover and the trunk

floor carpeting over the damaged tire.

In case of emergency 6-7

Z X

WARNING

c Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an accident or sudden stop.

c The spare tire is designed for emer- gency use. See specific instructions under the heading ‘‘Wheels and tires’’ in do-it- yourself’’ section of this manual.

‘‘Maintenance

and

the

JUMP STARTING

To start your engine with a booster battery, the instructions and precautions below must be followed.

WARNING

c If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.

c Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.

c Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a corrosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with anything, immediately flush the con- tacted area with water.

c Keep the battery out of the reach of

children.

c The booster battery must be rated at 12 volts. Use of an improperly rated battery can damage your vehicle.

Z X

WCE0008

7. Install the jack in its storage area and

tighten the jack screw clockwise.

8. Close the trunk.

6-8 In case of emergency

c Whenever working on or near a bat- tery, always wear suitable eye pro- tectors (for example, goggles or in- dustrial and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.

spectacles)

safety

c Do not attempt to jump start a frozen battery. It could explode and cause serious injury.

c Your vehicle has an automatic en- gine cooling fan. It could come on at any time. Keep hands and other ob- jects away from it.

Always follow the instructions below. Failure to do so could result in damage to the charging system and cause per- sonal injury. 1. If the booster battery is in another vehicle, position the two vehicles to bring their batteries into close proximity to each other. Do not allow the two vehicles to touch. 2. Apply the parking brake. Move the selec- tor lever to N (Neutral) (on automatic transmission models, move the shift se- lector lever to P (Park)). Switch off all unnecessary electrical systems (lights,

ACE1013

heater, air conditioner, etc.).

3. Cover the battery with an old cloth to

reduce explosion hazard.

4. Connect jumper cables in the sequence

illustrated.

CAUTION

c Always connect positive (+) to positive (+) and negative (−) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery.

In case of emergency 6-9

Z X

PUSH STARTING

CAUTION

c Automatic transmission models can- not be push started. This may cause transmission damage.

c Three way catalyst equipped models should not be started by pushing. The three way catalyst may be dam- aged.

c Never try to start the vehicle by tow- ing it. When the engine starts, the forward surge could cause the ve- hicle to collide with the tow vehicle.

c Make sure the jumper cables do not touch moving parts in the engine com- partment and that the cable clamps do not contact any other metal.

5. Start the engine of the booster vehicle

and let it run for a few minutes.

6. Keep the engine speed of the booster vehicle at about 2,000 rpm, and start the engine of the vehicle being jump started.

CAUTION

Do not keep the starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.

7. After starting the engine, carefully dis- connect the negative cable and then the positive cable.

8. Be sure to dispose of the cloth used to cover the vent holes as it may be con- taminated with corrosive acid.

6-10 In case of emergency

IF YOUR VEHICLE OVERHEATS

If your vehicle is overheating (indicated by an extremely high temperature gauge read- ing), or if you feel a lack of engine power, detect abnormal noise, etc., take the follow- ing steps.

WARNING

c Do not continue to drive if your ve- hicle overheats. Doing so could cause a vehicle fire.

c To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radiator cap is removed, pressurized hot water will spurt out, possibly causing serious injury.

c Do not open the hood if steam is

coming out.

1. Move the vehicle safely off

the road, apply the parking brake and move the selector lever to N (Neutral) (manual transmission) or the shift selector lever to P (Park) (automatic transmission). Do not stop the engine.

2. Turn off the air conditioner. Open all the windows, move the heater or air condi- tioner temperature control to maximum

Z X

WARNING

Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or get caught in, engine belts or the engine cooling fan. The engine cooling fan can start at any time when the coolant temperature is high.

6. After the engine cools down, check the coolant level in the reservoir tank with the engine running. Add coolant to the res- ervoir tank if necessary. Have your ve- hicle repaired at an authorized NISSAN dealer.

hot and fan control to high speed.

3. Get out of the vehicle. Look and listen for steam or coolant escaping from the ra- diator before opening the hood. Wait until no steam or coolant can be seen before proceeding.

4. Open the hood.

WARNING

If steam or water is coming from the engine, stand clear to prevent getting burned.

5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running. The radiator hoses and radia- tor should not leak water. If coolant is leaking, the water pump belt is missing or loose, or the cooling fan does not run, stop the engine.

TOWING YOUR VEHICLE

When towing your vehicle, all State (Provin- cial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from an authorized NISSAN dealer. Local service operators are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle. is advisable to have the service operator carefully read the following precautions:

It

WARNING

c Never ride in a vehicle that is being

towed.

c Never get under your vehicle after it

has been lifted by a tow truck.

CAUTION

c When towing, make sure that the transmission, axles, steering system and powertrain are in working con- dition. If any unit is damaged, dollies must be used.

In case of emergency 6-11

Z X

c Always attach safety chains before

towing.

ACE0511

TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the

6-12 In case of emergency

ground or place the vehicle on a flat bed truck as illustrated.

CAUTION

c Never tow automatic transmission models with the front wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive dam- age to the transmission. If it is nec- essary to tow the vehicle with the rear wheels raised, always use tow- ing dollies under the front wheels.

c When towing automatic transmis- sion models with the front wheels on towing dollies, or when towing manual transmission models with the front wheels on the ground:

c Turn the ignition key to the OFF position, and secure the steer- ing wheel in a straight ahead position with a rope or similar device. Never secure the steer- ing wheel by turning the igni- tion key to the LOCK position. This may damage the steering lock mechanism.

c Move the shift lever to the N

(Neutral) position.

Z X

When towing automatic or manual transmission models with the rear wheels on the ground (if you do not use towing dollies): Always release the parking brake.

VEHICLE RECOVERY (freeing a stuck vehicle) c Tow chains or cables must be attached only to the main structural members of the vehicle.

c Pulling devices should be routed so they do not touch any part of the suspension, steering, brake or cooling systems.

c Always pull the cable straight out from the front or rear of the vehicle. Never pull the vehicle at an angle.

c Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.

c Stand clear of a stuck vehicle.

WARNING

Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.

CE1052

In case of emergency 6-13

Z X

MEMO

6-14 In case of emergency

Z X

7 Appearance and care

Cleaning exterior ....................................................7-2
Washing.............................................................7-2
Waxing...............................................................7-2
Removing spots.................................................7-3
Underbody .........................................................7-3
Glass..................................................................7-3
Aluminum alloy wheels......................................7-3
Chrome parts.....................................................7-3

Cleaning interior .....................................................7-4
Seat belts ..........................................................7-5
Corrosion protection...............................................7-5

Most common factors contributing to vehicle corrosion................................................7-5
Environmental factors influence the rate of corrosion........................................................7-5
To protect your vehicle from corrosion .............7-5

Z X

CLEANING EXTERIOR

MAI0001

In order to maintain the appearance of your vehicle, it is important to take proper care of it. In the following cases, please wash your vehicle as soon as possible to protect the paint surface: c after a rainfall to prevent possible dam-

age from acid rain.

c after driving on coastal roads. c when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface.

7-2 Appearance and care

c when dust or mud builds up on the paint

surface.

Whenever possible, store or park your ve- hicle inside a garage or in a covered area. When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint sur- face when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water.

CAUTION

c Do not wash the vehicle with strong household soap, strong chemical detergents, gasoline or solvents.

c Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted.

c Avoid using tight-napped or rough cloths such as washing mitts. Care must be taken when removing caked-on dirt or other foreign sub- stances so that the paint surface is not scratched or damaged.

Rinse the vehicle thoroughly with plenty of clean water. Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. There- fore, these areas must be cleaned regularly. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. After waxing, polishing is recommended to remove built-up residue and to avoid a ‘‘weathered’’ appearance. An authorized NISSAN dealer can assist

Z X

you in choosing the proper product. c Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax.

c Do not use a wax containing any abra- sives, cutting compounds or cleaners that may damage the vehicle finish.

c If the surface does not polish easily, use

a “road tar” remover and wax again.

Machine compounding or aggressive pol- ishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. Only use black wax or black shoe polish on black urethane or polypropylene bumpers. REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning prod- ucts are available at an authorized NISSAN dealer or any automotive accessory store. UNDERBODY In areas where road salt is used in winter, the underbody must be cleaned regularly. This prevents dirt and salt from building up

and causing the acceleration of underbody and suspension corrosion. Before winter and again in the spring, the underseal must be checked and, if necessary, re-treated. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is nor- mal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth easily remove this film.

CAUTION

When cleaning the inside of the win- dows, do not use sharp-edged tools, abrasive cleaners or chlorine based disinfectant cleaners. They could dam- age the electrical conductors, radio an- tenna elements or rear window defog- ger elements.

ALUMINUM ALLOY WHEELS Wash the wheels regularly, especially dur- ing winter months in areas where road salt is used. If not removed, road salt could discolor the wheels.

CHROME PARTS Clean all chrome parts regularly with a non-abrasive chrome polish to maintain the finish.

Appearance and care 7-3

Z X

are fitted for your vehicle and are prop- erly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn.

CLEANING INTERIOR

Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry soft cloth. Before using any fabric protector, read the manu- facturer’s recommendations. Some fabric protectors contain chemicals that may stain or bleach the seat material. Use a cloth dampened only with water, to clean the meter and gauge lens.

CAUTION

c Never use benzine, thinner, or any

similar material.

c Never use fabric protectors unless recommended by the manufacturer. c Do not use glass or plastic cleaner on meter or gauge lens covers. It may damage the lens cover.

Floor mats The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they 7-4 Appearance and care

WAI0002

Floor mat positioning aid All models include front floor mat brackets to act as a floor mat positioning aid. NIS- SAN floor mats have been specially de- signed for your vehicle model. The floor mat has a grommet hole incorporated in it. Po- sition the mat by placing the floor mat bracket hook through the floor mat grommet hole while centering the mat in the footwell. Periodically check to make certain the mats are properly positioned.

Z X

SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry com- pletely in the shade before using them. See ‘‘Seat belt maintenance’’ in the ‘‘Seats, re- straints and supplemental air bag systems’’ section of this owner’s manual.

WARNING

Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye, or chemical solvents to clean the seat belts, since these materials may se- verely weaken the seat belt webbing.

CORROSION PROTECTION

MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1. The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.

2. Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents.

ENVIRONMENTAL FACTORS IN- FLUENCE THE RATE OF COR- ROSION Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate cor- rosion. Wet floor coverings will not dry com- pletely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated: c in areas of high relative humidity.

c in areas where the temperatures stay

above freezing.

c where atmospheric pollution exists. c where road salt is used. Temperature High temperatures accelerate the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates the disintegra- tion of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION c wash and wax your vehicle often to keep

the vehicle clean.

c always check for minor damage to the paint and repair it as soon as possible. c keep drain holes at the bottom of the doors open to avoid water accumulation. c check the underbody for accumulation of Appearance and care 7-5

Z X

sand, dirt or salt. If present, wash with water as soon as possible. CAUTION

c NEVER remove dirt, sand or other debris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.

c Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them.

Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, cleaned periodically. For additional protection against rust and corrosion, which may be required in some areas, consult an authorized NISSAN dealer.

the underbody must be

7-6 Appearance and care

Z X

MEMO

Appearance and care 7-7

Z X

8 Maintenance and do-it-yourself

Maintenance requirements.....................................8-2
General maintenance.............................................8-3

Explanation of general maintenance items ..................................................................8-3
Maintenance precautions .......................................8-5
Engine compartment check locations - QG engine .............................................................8-7
Engine compartment check locations - QR engine .............................................................8-8
Engine cooling system ...........................................8-9
Checking engine coolant level ..........................8-9
Changing engine coolant ................................8-10
Engine oil .............................................................8-12
Checking engine oil level ................................8-12
Changing engine oil ........................................8-13
Changing engine oil filter.................................8-14
Automatic transmission fluid ................................8-15
Temperature conditions for checking..............8-16
Power steering fluid..............................................8-17
Brake and clutch fluid...........................................8-18
Brake fluid........................................................8-18
Clutch fluid.......................................................8-18

Window washer fluid ............................................8-19
Battery ..................................................................8-19
Jump starting...................................................8-21
Drive belts ............................................................8-22
Spark plug ............................................................8-23
Replacing spark plugs.....................................8-23
Air cleaner ............................................................8-24
Cabin air filter (if so equipped)........................8-24
Windshield wiper blades ......................................8-28
Cleaning ..........................................................8-28
Replacing.........................................................8-28
Parking brake and brake pedal............................8-29
Checking park brake .......................................8-29
Checking brake pedal .....................................8-30
Brake booster ..................................................8-30
Clutch pedal .........................................................8-31
Checking clutch pedal .....................................8-31
Fuses....................................................................8-31
Engine compartment .......................................8-31
Passenger compartment .................................8-34
Keyfob battery replacement .................................8-35
Lights....................................................................8-36

Z X

Headlights........................................................8-36
Fog lights (if so equipped)...............................8-39
Exterior and interior lights ...............................8-40
Wheels and tires ..................................................8-43

Tire pressure ...................................................8-43
Types of tires...................................................8-44
Tire chains.......................................................8-45
Changing wheels and tires..............................8-45

Z X

forms the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way.

MAINTENANCE REQUIREMENTS

Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day- to-day and regular maintenance is essential to maintain your NISSAN’s good mechani- cal condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. Scheduled maintenance For your convenience, both required and optional scheduled maintenance items are described and listed in your ‘‘NISSAN Ser- vice and Maintenance Guide.’’ You must refer to that guide to ensure that necessary maintenance is performed on your Nissan at regular intervals. General maintenance General maintenance includes those items which should be checked during normal 8-2 Maintenance and do-it-yourself

day-to-day operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these maintenance procedures regularly as prescribed. Performing general maintenance checks re- quire minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, an authorized NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an autho- rized NISSAN dealer. NISSAN technicians are well-trained spe- cialists who and are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that an authorized NISSAN dealer’s service department per-

Z X

GENERAL MAINTENANCE

During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have an authorized NISSAN dealer do it promptly. In addition, you should notify an authorized NISSAN dealer if you think that repairs are required. When performing any checks or mainte- nance work, closely observe the ‘‘Mainte- nance precautions’’ later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with ‘‘*’’ is found later in this sec- tion. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Tires* Check the pressure with a gauge at least once a month and always prior to long distance trips, including the spare, and ad- just to the specified pressure if necessary.

Check carefully for damage, cuts or exces- sive wear. Wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Wheel alignment and balance If the ve- hicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. c For additional information regarding tires, refer to ‘‘Important Tire Safety Informa- tion’’ in the Warranty Information Booklet (US) or ‘‘Tire Safety Information’’ in the Warranty and Roadside Assistance Infor- mation booklet (Canada).

Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other dam- age. Have a damaged windshield repaired by a qualified repair facility.

Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Doors, hood and tailgate Check that the doors, hood and tailgate operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, latch pins, rollers and links as necessary. Make sure that the secondary latch keeps the hood from open- ing when the primary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Additional information on the following items with an ‘‘*’’ is found later in this section. Warning lights and chimes Make sure all 8-3

Maintenance and do-it-yourself

Z X

warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Steering wheel Check for changes in the steering conditions, such as excessive free- play, hard steering or strange noises. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched posi- tions. Seat belts Check that all parts of the seat belt system (e.g., buckles, anchors, adjust- ers and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. 8-4 Maintenance and do-it-yourself

Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mat away from the pedal. Clutch pedal* Make sure the pedal oper- ates smoothly and check that it has the proper free travel. Brakes Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when de- pressed fully. Check the brake booster func- tion. Be certain to keep the floor mat away from the pedal. Parking brake* Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Automatic transmission P (Park) posi- tion mechanism Check that the lock re- lease button on the selector lever operates properly and smoothly. On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes.

Under the hood and vehicle The maintenance items listed here should be checked periodically (e.g., each time you check the engine oil or refuel). Additional information on the following items with an ‘‘*’’ is found later in this section. Windshield washer fluid* Check that there is adequate fluid in the reservoir. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait a few minutes for the oil to drain back into the oil pan. Brake and clutch fluid levels* Make sure that the brake and clutch fluid level is be- tween the MIN and MAX lines on the reser- voir. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Automatic transmission fluid level* Check the level after putting the selector lever in P with the engine idling at operating temperature.

Z X

may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the ‘‘Appearance and care’’ section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately.

Engine coolant level* Check the coolant level when the engine is cold. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, de- formation, rot or loose connections. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Battery* Check the fluid level in each cell. It should be between the MAX and MIN lines. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by an autho- rized NISSAN dealer. See the carbon mon- oxide warning in the ‘‘Starting and driving’’ section of this manual. Underbody The underbody is frequently exposed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these sub- stances from the underbody, otherwise rust

MAINTENANCE PRECAUTIONS

When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed.

WARNING

c Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. For manual trans- mission models, move the shift lever to N (Neutral). For automatic trans- mission models, move the shift se- lector lever to P (Park).

c Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.

c Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warn- ing, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always dis- connect the negative battery cable before working near the fan.

Maintenance and do-it-yourself

8-5

Z X

c If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.

c It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc., before working on your vehicle.

c Always wear eye protection when-

ever you work on your vehicle.

c If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.

c Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands.

c Keep smoking materials, flame and sparks away from the fuel tank and battery.

c On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by an authorized NISSAN dealer because the fuel lines are under high pressure even when the engine is off.

c Avoid contact with used engine oil and coolant. Improperly disposed engine oil, engine coolant, and/or other vehicle fluids can damage the environment. Always conform to lo- cal regulations for disposal of ve- hicle fluid.

CAUTION

c Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.

c Never connect or disconnect the bat- tery or any transistorized compo- nent while the ignition switch is in the ON position.

c Never leave the engine or automatic transmission related component harnesses disconnected while the ignition switch is in the ON position.

This ‘‘Maintenance and do-it-yourself’’ sec- tion gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN service manual is also available. See ‘‘Owner’s Manual/Service Manual order information’’ in the ‘‘Technical and consumer information’’ section. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect your warranty coverage. If in doubt about any servicing, have it done by an authorized NISSAN dealer.

8-6 Maintenance and do-it-yourself

Z X

ENGINE COMPARTMENT CHECK LOCATIONS - QG ENGINE

1. Engine oil filler cap 2. Spark plug caps 3. Brake fluid reservoir 4. Clutch fluid reservoir (M/T model) 5. Air Cleaner 6. Battery 7. Fuse/Fusible link holds 8. Radiator cap 9. Engine oil dipstick 10. Windshield washer fluid reservoir 11. Coolant reservoir 12. Power steering fluid reservoir * Engine cover removed for clarity

WDI0024

Maintenance and do-it-yourself

8-7

Z X

ENGINE COMPARTMENT CHECK LOCATIONS - QR ENGINE

1. Engine oil filler cap 2. Spark plug caps 3. Brake fluid reservoir 4. Clutch fluid reservoir (M/T model) 5. Air Cleaner 6. Battery 7. Fuse/Fusible link holds 8. Radiator cap 9. Engine oil dipstick 10. Windshield washer fluid reservoir 11. Coolant reservoir 12. Power steering fluid reservoir *Engine cover removed for clarity

8-8 Maintenance and do-it-yourself

LDI0108

Z X

ENGINE COOLING SYSTEM

The engine cooling system is filled at the factory with a high-quality, year-round, anti- freeze coolant solution. The anti-freeze so- lution contains rust and corrosion inhibitors; therefore, additional engine cooling system additives are not necessary.

CAUTION

When adding or replacing coolant, be sure to use only an ethylene glycol anti-freeze with the proper mixture ratio of 50% Genuine Nissan Anti-freeze coolant or equivalent and 50% deminer- alized or distilled water. The use of other types of coolant solutions may damage the engine cooling system.

Outside

temperature

down to

°C

−35

°F

−30

Genuine

NISSAN Anti- freeze coolant or equivalent

Demineral-

ized or distilled water

50%

50%

WARNING

c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

c The radiator is equipped with a pres- sure type radiator cap. To prevent engine damage, use only a genuine NISSAN radiator cap.

ADI1137

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below MIN, add coolant up to the MAX level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient cool- ant the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level.

in the radiator,

fill

Maintenance and do-it-yourself

8-9

Z X

c Keep coolant out of reach of children

and pets.

If the cooling system frequently requires coolant, have it checked by an autho- rized NISSAN dealer. CHANGING ENGINE COOLANT c Major cooling system repairs should be performed by an authorized NISSAN dealer. The service procedures can be found in the NISSAN Service Manual.

c Improper servicing can result in reduced heater performance and engine over- heating.

WARNING

c To avoid the danger of being scalded, never change the coolant when the engine is hot.

c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

c Avoid direct skin contact with used coolant. is made, wash thoroughly with soap or hand cleaner as soon as possible.

If skin contact

8-10 Maintenance and do-it-yourself

WDI0109

Engine coolant must be disposed of properly. Check your local regulations. 1. Open the radiator drain plug.

Z X

WDI0106

WDI0041

WDI0042

2. Open the drain plug on the engine block. 3. Open the radiator cap to drain the cool-

ant. c Waste coolant must be disposed of

properly.

c Check your local regulations.

4. Flush the cooling system by running

fresh water through the radiator.

5. Close the drain plugs on the radiator and

the engine block securely.

6. See the ‘‘Technical and consumer infor- mation’’ section for cooling system ca- pacity. Fill the radiator slowly with the proper mixture of coolant and water. Fill the reservoir tank up to the MAX level.

7. For QG18DE engine only, open and close the air release plug(s) to release air. Then fill the radiator again and install the radiator cap.

8. Start the engine, and warm it up until it reaches normal operating temperature. Then race the engine two or three times under no load. Watch the engine coolant

Maintenance and do-it-yourself

8-11

Z X

temperature gauge for signs of overheat- ing.

9. Stop the engine. After it completely cools down, refill the radiator up to the filler opening. Fill the reservoir tank up to the MAX level.

10. For QG18DE engine only, open and close the air release plug(s) to release air. Then fill the radiator again and install the radiator cap.

11. Check the drain plugs on the radiator and the engine block for any sign of leakage. For QG18DE only, also check the air release plug for any sign of leakage.

8-12 Maintenance and do-it-yourself

ENGINE OIL

WDI0014

WDI0110

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and

apply the parking brake.

2. Start the engine and let it idle until

reaches operating temperature.

it

3. Turn off the engine. Wait a few minutes for the oil to drain back into the oil pan.

4. Remove the dipstick and wipe it clean.

Reinsert it all the way.

level.

5. Remove the dipstick again and check the oil It should be between the H (High) and L (Low) marks. If the oil level is below the L (Low) mark, remove the oil filler cap and pour recommended oil through the opening. Do not overfill.

Z X

DI1252M

LDI0016

WDI0112

6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the sever- ity of operating conditions.

CAUTION

Oil level should be checked regularly. Operating the engine with an insuffi- cient amount of oil can damage the engine, and such damage is not cov- ered by warranty.

CHANGING ENGINE OIL 1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until it reaches operating

temperature, and then turn it off.

3. Remove the oil filler cap. 4. Place a large drain pan under the drain

plug.

5. Remove the drain plug with a wrench and

completely drain the oil.

If the oil filter is to be changed, remove and replace it at this time. See ‘‘Chang- ing engine oil filter’’ later in this section.

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

c Waste oil must be disposed of prop-

erly.

c Check your local regulations.

Maintenance and do-it-yourself

8-13

Z X

WARNING

c Prolonged and repeated contact with used engine oil may cause skin can- cer.

c Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

c Keep used engine oil out of reach of

children.

6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Drain plug tightening torque: 22 to 29 ft-lb (29 to 39 Nzm)

Do not overtighten.

7. Refill engine with recommended oil through the oil filler opening then install the oil filler cap securely. See the ‘‘Technical and consumer infor- mation’’ section for drain and refill capac- ity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.

8. Start

the engine. Check for

leakage around the drain plug and oil filter. Cor- rect as required.

9. Turn the engine off and wait several level with the

minutes. Check the oil dipstick. Add engine oil if necessary.

8-14 Maintenance and do-it-yourself

LDI0017

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and

apply the parking brake.

2. Turn the engine off. 3. Place a large drain pan under the oil

filter.

4. Loosen the oil

filter with an oil

wrench. Then remove the oil turning it by hand.

filter filter by

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

Z X

AUTOMATIC TRANSMISSION FLUID

9. Turn the engine off and wait several minutes. Check the oil level. Add engine oil if necessary.

WDI0113

5. Wipe the engine oil filter mounting sur-

face with a clean rag. Be sure to remove any old gasket mate- rial remaining on the mounting surface of the engine.

6. Coat the gasket on the new filter with

clean engine oil.

7. Screw on the oil filter until a slight resis- tance is felt, then tighten an additional 2/3 turn.

8. Start the engine and check for leakage around the oil filter. Correct as required.

LDI0018

WARNING

c When the engine is running, keep hands, jewelry and clothing away from any moving parts such as the cooling fan and drive belts.

c Automatic transmission fluid is poi- sonous and should be stored care- fully in marked containers out of the reach of children.

Maintenance and do-it-yourself

8-15

Z X

3. Check the fluid level with the engine

idling.

4. Remove the dipstick and wipe it clean

with lint-free paper.

5. Reinsert

the dipstick into the dipstick

tube as far as it will go.

6. Remove the dipstick and note the read- ing. If the level is at the low side of either range, add fluid through the dipstick tube.

TEMPERATURE CONDITIONS FOR CHECKING c The fluid level should be checked using the HOT range on the dipstick after the following conditions have been met:

— The engine should be warmed up to

operating temperature.

— The vehicle should be driven at least 5

minutes.

— The automatic transmission fluid should be warmed to between 122 and 176°F (50 and 80°C).

8-16 Maintenance and do-it-yourself

WDI0133

c The fluid can be checked at fluid tem- peratures of 86 to 122°F (30 to 50°C) using the COLD range on the dipstick after the engine is warmed up and before driving. However, the fluid should be re-checked using the HOT range.

1. Park the vehicle on a level surface and

set the parking brake.

2. Start the engine and then move the shift selector lever through each gear range. Move the shift selector lever to P (Park) after you have moved it through all ranges.

Z X

CAUTION

DO NOT OVERFILL. Use ONLY Nissan Matic ‘D’ (Continental U.S. and Alaska) or Canada NISSAN Automatic Trans- mission Fluid. DexronTM III/MerconTM or equivalent may also be used. Out- side the continental United States and Alaska contact an authorized NISSAN dealership for more information re- garding suitable fluids, including rec- of DexronTM ommended III/MerconTM Automatic Transmission Fluid.

brand(s)

NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the accurate fluid level cannot be read. You should wait until the fluid has cooled down (about 30 minutes) be- fore checking fluid level.

POWER STEERING FLUID

WDI0137

WDI0138

Check the fluid level in the reservoir. The fluid level should be checked using the HOT range on the side of the fluid reservoir at fluid temperatures of 122 to 176°F (50 to 80°C) or using the COLD range on the side of the fluid reservoir at fluid temperatures of 32 to 86°F (0 to 30°C).

CAUTION

c DO NOT OVERFILL. c Recommended fluid is Genuine

NISSAN PSFII or equivalent.

Maintenance and do-it-yourself

8-17

Z X

BRAKE AND CLUTCH FLUID

WDI0039

LDI0035

BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid is below the MIN line or the brake warning light comes on, add Genuine Nis- san Brake fluid or equivalent DOT 3 fluid up to the MAX line. fluid must be added frequently, the system should be thoroughly checked by an authorized NISSAN dealer.

If

CLUTCH FLUID Check the clutch fluid level in the reservoir (manual transmission only). If the fluid level is below the MIN line, add Genuine Nissan Brake fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added fre- quently, the system should be thoroughly checked by an authorized NISSAN dealer. For further brake and clutch fluid specifica- tion information, refer to “Capacities and recommended fuel/lubricants” in the “Tech- nical and consumer information” section of this manual.

8-18 Maintenance and do-it-yourself

WARNING

Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the brake system and af- fect the vehicle’s stopping ability.

CAUTION

Do not spill the fluid on painted sur- faces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

Z X

WINDOW WASHER FLUID

BATTERY

WDI0040

To fill the window washer fluid reservoir, lift the cap off the reservoir tank and pour the window washer fluid into the tank opening. Add a washer solvent to the water for better cleaning. In the winter season, add a wind- shield washer antifreeze. Follow the manu- facturer’s instructions for the mixture ratio. USA Only Fill the window washer fluid reservoir peri- odically. Perform the refilling operation more often under driving conditions that require an increased amount of window washer fluid.

Canada Only Add fluid when the low washer fluid warning light comes on. Add a washer solvent to the water for better cleaning. In the winter sea- son, add a windshield washer antifreeze. Follow the manufacturer’s instructions for the mixture ratio.

CAUTION

Do not substitute engine anti-freeze coolant for windshield washer solution. This may result in damage to the paint.

c Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water.

c Make certain the terminal connections

are clean and securely tightened.

c If the vehicle is not to be used for 30 days or longer, disconnect the negative (−) bat- tery terminal cable to prevent discharge.

WARNING

c Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by the battery is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention.

c Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, re- duce battery life, and in some cases lead to an explosion.

Maintenance and do-it-yourself

8-19

Z X

c When working on or near the battery, always wear suitable eye protection and remove all jewelry.

c Battery posts, terminals and related accessories contain lead com- pounds. Wash hands after handling. c Keep the battery out of the reach of

children.

WDI0020

WDI0021

1. Remove the battery caps with a screw-

driver as shown.

2. Check the fluid level in each cell.

If it is necessary to add fluid, add only distilled water to bring the level up to the OK level indicator in each filler opening. Do not overfill. Vehicles operated in high temperatures or under severe conditions require checks of the battery fluid level.

8-20 Maintenance and do-it-yourself

Z X

JUMP STARTING If jump starting is necessary, see the ‘‘In case of emergency’’ section of this owner’s manual. If the engine does not start by jump starting, the battery may have to be re- placed. Contact an authorized NISSAN dealer.

Maintenance and do-it-yourself

8-21

Z X

DRIVE BELTS

WARNING

Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.

1. Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by an autho- rized NISSAN dealer.

2. Have the belts checked regularly for con- dition and tension in accordance with the maintenance schedule found in the

8-22 Maintenance and do-it-yourself

‘‘NISSAN Service and Maintenance Guide’’.

WDI0111

Z X

SPARK PLUG

DI1229M

ADI1100

WARNING

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.

REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum- tipped spark plugs as frequently as conven- tional type spark plugs because they last much longer. Follow the maintenance schedule, but do not reuse the spark plugs by cleaning or regapping. c Always replace spark plugs with rec-

ommended or equivalent ones.

1. On the 1.8L engine, disconnect the igni- tion coil connectors. Remove the ignition coil bolts.

2. Disconnect the spark plug cables from

the spark plugs. When disconnecting, always hold the boots, not the cables. Mark all cables to identify their original locations.

3. Remove the spark plugs with a spark

plug socket. The plug socket has a rubber seal that holds the spark plug so it does not fall when it is pulled out. Make sure each spark plug is snugly fitted into the spark plug socket.

4. Fit the new plugs, one at a time, into the spark plug socket and install them. Use only the specified spark plugs. Turn each plug several full turns by hand, then tighten with the spark plug socket to the correct torque. Do not overtighten. Spark plug tightening torque: 14 to 22 ft-lb (20 to 29 Nzm)

Maintenance and do-it-yourself

8-23

Z X

AIR CLEANER

5. Holding the boot, reconnect each high tension cable to its proper spark plug by pushing it on until you feel a snap.

6. On the 1.8L engine, install the ignition

coil bolt. Ignition coil bolt tightening torque:

33 to 44 in-lb (3.8 - 5.0 Nzm)

Connect the ignition coil connector.

ADI0631

The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance the ‘‘NISSAN Service and Maintenance Guide’’. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.

intervals

shown

in

WARNING

c Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops the

8-24 Maintenance and do-it-yourself

flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed and be careful when working on the engine with the air cleaner removed.

c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

CABIN AIR FILTER (if so equipped) The cabin air filter restricts the entry of airborne dust and pollen particles and re- duces some objectionable outside odors. The filter is located behind the glove box. Refer to the ‘‘NISSAN Service and Mainte- nance Guide’’ for change intervals. To replace the filter, perform the following procedure:

Z X

LDI0139

LDI0140

LDI0141

1. Remove the glove box door by removing

the 2 lower hinge pins.

2. Remove the 2 screws securing the glove

box frame.

3. Remove the 2 screws securing the glove box door latch. Remove the latch by pulling it down.

4. Remove the glove box frame by pulling it away from the instrument panel to disen- gage the retaining clips.

5. Remove the filter cover from the intake unit by disengaging the 2 hook tabs at the bottom of the cover.

Maintenance and do-it-yourself

8-25

Z X

LDI0142

NOTE: The filter is marked ‘‘UP’’ with an arrow. The end of the filter with the arrow should face the rear of the vehicle. 6. Slide the filter into the housing.

8-26 Maintenance and do-it-yourself

LDI0143

Z X

NOTE: Make sure the filter sits on top of the 2
supporting tabs on the housing. 7. Replace the cover by inserting the upper tabs inside the housing slot and pushing the hook tabs until they snap onto the housing lip.

8. Install the glove box frame and latch. 9. Install the glove box door. 10. Fill out the date information on the small replacement label and attach it to the glove box lid.

Maintenance and do-it-yourself

8-27

Z X

WINDSHIELD WIPER BLADES

CLEANING If your windshield is not clear after using the windshield washer or if the wiper blade chatters when running, wax or other mate- rial may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter- gent. Then rinse the blade with clear water. If your windshield is still not clear after 8-28 Maintenance and do-it-yourself

cleaning the blades and using the wiper, replace the blades.

CAUTION

Worn windshield wiper blades can damage the windshield and impair driver vision.

REPLACING Replace the wiper blades if they are worn 1. Lift the wiper arm away from the wind-

shield.

2. Push the tab, then move the wiper blade

ADI1022

down the wiper arm to remove.

3. Remove the wiper blade. 4. Insert the new wiper blade onto the wiper

arm until it clicks.

CAUTION

c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.

Z X

c Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure.

PARKING BRAKE AND BRAKE PEDAL

WDI0036

CHECKING PARK BRAKE From the released position, pull the parking brake lever up slowly and firmly. the number of clicks is out of the range listed above, see an authorized NISSAN dealer.

If

Maintenance and do-it-yourself

8-29

Z X

ADI0613

When you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may cause clogging or im- proper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin.

DI1020M

CHECKING BRAKE PEDAL With the engine running, check the distance between the upper surface of the pedal and the metal floor. If it is out of the range shown above, see an authorized NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front (and rear, if equipped) disc-type brakes self-adjust every time the brake pedal is applied. The rear drum-type brakes also self-adjust every time the brake pedal is applied. 8-30 Maintenance and do-it-yourself

If the brake pedal goes down farther than normal, it may be due to a lack of adjust- ment of the rear drum brakes. To adjust, apply the parking brake several times.

WARNING

See an authorized NISSAN dealer for a brake system check if the brake pedal height does not return to normal.

Brake pad wear indicators The disc brake pads on your vehicle have an audible wear indicator. When a brake pad requires replacement, it makes a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occasional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is nor- mal and does not affect the function or performance of the brake system. The rear drum brakes (if so equipped) do not have audible wear indicators. Should

you ever hear an unusually loud noise from the rear drum brakes, have them inspected as soon as possible by an authorized