1999 Nissan Quest Owners Manual

SEATS/FLOOR MATS

SEATING ARRANGEMENTS Many different arrangements for passenger seating or cargo hauling are available as you will see in the following illustrations. The second row seats may be removed and the third row seat may be moved forward to the second row seating position. The second and third row seats have an optional fold- down table-top feature. This offers a variety of uses for the vehicle when moving or stopped. The illustrations shown reflect the different seating positions available. Before you begin to arrange the seats in your vehicle, read all of the cautions and warnings in this chapter, including the following section on the removable floor mats. Also observe any labels that are in the vehicle.

WARNING

c While the vehicle is in motion, pas- sengers should always be seated in a forward facing direction in a seat which is properly secured and ad- justed. Seat belts should always be used. Sitting without a seat belt in a seat that is not properly secured in one of the locations shown in this chapter, or in a place without a seat and seat belt can result in personal injury in a sudden stop or collision. c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an acci- dent, you could be thrown into it and receive neck or other serious inju- ries. You could also slide under the lap belt and receive serious internal injuries.

c For the most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.

c It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these ar- eas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. c Be sure everyone in your vehicle is in a seat and using a seat belt prop- erly.

c Do not place hard items such as coffee mugs or drinking glasses on the tabletop seats when the vehicle is moving. Any item can become a projectile inside a vehicle involved in a collision. To help prevent personal injury, never leave loose items on the fold-down tabletop seats when the vehicle is moving.

1-68 Seats, restraints and supplemental air bag systems

Z X

FLOOR MAT POSITIONING

ARS1216

ARS1217

SEVEN PASSENGER SEATING Removable floor mats Whenever you remove the mats for any reason, the mats must be reinstalled before passengers ride in your vehicle. The floor mats are specifically designed to keep objects out of the seat tracks. The cargo mat is reversible.

THREE-PASSENGER BENCH SEAT IN STORAGE POSITION

CAUTION

It is important to replace the floor mats whenever they are removed for any reason. The floor mats are intended to help prevent the possibility that high heeled shoes or similar objects might become stuck in the seat tracks. Failure to replace the floor mats might result in personal injury.

Be sure to keep the seat tracks clear of debris by cleaning them periodically. Review the following illustrations so you will know the proper way to place the floor mats with the various seating arrangements available in your vehicle.

Seats, restraints and supplemental air bag systems 1-69

Z X

FIVE PASSENGER SEATING

ARS1218

ARS1219

1-70 Seats, restraints and supplemental air bag systems

Z X

FIVE PASSENGER SEATING WITH CARGO ROOM The step mat is not used in this seating configuration.

THREE-PASSENGER BENCH SEAT IN FULLY FORWARD POSITION The step mat is not used in this seating configuration.

ARS1220

ARS1221

Seats, restraints and supplemental air bag systems 1-71

Z X

the vehicle that

c Do not allow people to ride in any area of is not equipped with seats and seat belts. c Be sure everyone in your vehicle is in a seat and is using a seat belt properly.

c Failure to follow proper seating in- structions in this section could re- sult in serious personal injury in an accident or during a sudden stop.

over the floor mat positioning bracket lo- cated at the base of the driver’s seat. Push the positioning pins into the seat tracks to ensure correct installation, then straighten the mats as necessary. The step mat has holes in addition to pins. When the mats are arranged properly, the positioning pins of the two mats on either side of the step mat should fit through the holes in the step mat and into the seat track.

WARNING

c No occupant should ride in a vehicle seat unless it is in a normal riding arrangement and the seat belts are properly used.

c It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these ar- eas are more likely to be seriously injured or killed.

c Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

APD0083

FLOOR MAT POSITIONING AID Positioning pins are attached to three of the floor mats. The cargo mat and front mats do not have pins. However, the driver’s front floor mat has a grommet which is placed

1-72 Seats, restraints and supplemental air bag systems

Z X

SEAT POSITIONS

APD0096

WITH SECOND ROW BENCH SEAT The most common seating arrangement for seven passengers is with the three- passenger bench seat in seating position #1. This provides more leg room for the passengers sitting in the third row.

When more cargo area room is necessary, the three-passenger sliding bench seat can be moved to seating position #2 or #3. This seating arrangement provides less leg room for third row passengers, but more cargo room.

ARS1204

Seats, restraints and supplemental air bag systems 1-73

Z X

APD0042

APD0043

APD0049

The fold-down tabletop seats in the second and third rows provide a surface for eating or playing games on long trips.

If a considerable amount of cargo area room is needed, the seat cushion of the three-passenger sliding bench seat can be flipped up and the seat can be moved up to storage position #2, just behind the second row seat.

When maximum cargo area is needed and there are no rear seat passengers, the second row seat can be removed and the three-passenger sliding bench seat can be moved up to storage position #1, just behind the front seats.

1-74 Seats, restraints and supplemental air bag systems

Z X

APD0044

APD0045

APD0046

The second row bench seat can be folded down to serve as a tabletop for passengers sitting in the three-passenger bench seat.

The second and third row bench seats can be folded down to tabletops.

To increase cargo area space, the second row bench seat can be removed and the three-passenger sliding seat can be moved up to the second row position.

Seats, restraints and supplemental air bag systems 1-75

Z X

APD0047

APD0048

APD0050

The third seat can be folded down into a tabletop.

With the third seat folded down and the second seat removed, cargo can be placed in between the front seats and the third row seat. People should not be allowed to ride in areas meant for cargo. Passen- gers should always be properly re- strained in seat belts.

The second row seat can be folded down and the third row seat can be moved just behind it in a storage position.

1-76 Seats, restraints and supplemental air bag systems

Z X

APD0128

WITH SECOND ROW BUCKET SEATS The normal seating arrangement for seven passengers is with the three-passenger bench seat in seating position #1. This provides more leg room for the passengers sitting in the third row.

When one passenger in the three- passenger bench seat would like more leg room, one of the second row bucket seats can be removed.

ARS1195

Seats, restraints and supplemental air bag systems 1-77

Z X

When more cargo area room is necessary, the three-passenger sliding bench seat can be moved to seating position #2 or #3. This seating arrangement provides less leg room for third row passengers, but more cargo room.

ARS1205

APD0053

If passengers in the three-passenger bench seat would like more leg room, both second row bucket seats can be removed. The floor area should never be used by pas- sengers. Passengers should always be properly restrained by seat belts.

1-78 Seats, restraints and supplemental air bag systems

Z X

2 Instruments and controls

Meters and gauges ................................................2-3
Speedometer and odometer ..................................2-4
Tachometer ............................................................2-4
Engine coolant temperature gauge........................2-4
Fuel gauge .............................................................2-5
Warning/indicator lights and chimes ......................2-6
Theft warning (if so equipped) .............................2-10
Windshield wiper and washer switch...................2-12
Rear window wiper and washer switches............2-13
Rear window defogger switch..............................2-13
Headlight control switch .......................................2-13
Daytime running light system (Canada only).......2-14
Autolamp switch (if so equipped).........................2-14
Turn signal switch .............................................2-15
Cornering light......................................................2-15
Instrument brightness control...............................2-16
Hazard warning flasher switch.............................2-16
Cigarette lighter and ashtray (accessory)............2-17
Rear power point..................................................2-18
Cup holder............................................................2-18
Map pockets.........................................................2-20
Overhead storage compartment ..........................2-20

Power windows ....................................................2-21
Automatic power window switch ..........................2-21
Sunroof (if so equipped).......................................2-22
Manual vent windows...........................................2-23
Power vent windows (if so equipped)..................2-23
Interior lights.........................................................2-24
Luggage compartment lights................................2-24
Personal reading light ..........................................2-24
Map lights.............................................................2-25
Illuminated entry system ......................................2-25
Storage compartment for garage door transmitter (if so equipped) ..................................2-25
Integrated HomeLinkT universal transceiver (if so equipped) ....................................................2-27
Programming the HomeLinkT universal transceiver............................................................2-27
Operating the transceiver.....................................2-28
Programming problem diagnosis .........................2-28
Rolling codes........................................................2-29
Clearing the programming information.................2-30
If your vehicle is ever stolen ................................2-30

Z X

2-2 Instruments and controls

AIC1055

Z X

METERS AND GAUGES

AIC1094

Instruments and controls 2-3

Z X

SPEEDOMETER AND ODOMETER

TACHOMETER

ENGINE COOLANT TEMPERATURE GAUGE

AIC0003

AIC0110

AIC0004

Speedometer The speedometer indicates vehicle speed. Odometer The odometer records the total distance the vehicle has been driven. Trip odometer The trip odometer records the distance of individual trips. Before each trip, set the trip odometer to zero by pushing the RESET button.

2-4 Instruments and controls

The tachometer indicates engine speed in revolutions per minute (RPM).

CAUTION

When engine speed approaches the red zone, shift to a higher gear. Oper- ating the engine in the red zone may cause serious engine damage.

This gauge indicates the engine coolant temperature. The engine coolant tempera- ture varies with the outside air temperature and driving conditions.

CAUTION

If the gauge indicates engine coolant temperature above the normal range, stop the vehicle as soon as safely pos- sible. If the engine is overheated, con- tinued operation of the vehicle may seriously damage the engine. See the ‘‘In case of emergency’’ section for immediate action required.

Z X

CAUTION

c If the vehicle is driven with the fuel level very low, the malfunction indi- cator light may come on. Refuel as soon as possible. After driving for a while, the light should remain off. If the light remains on, have the ve- hicle inspected by an authorized NISSAN dealer.

information, see the For additional ‘‘Malfunction indicator light (MIL)’’ later in this section.

FUEL GAUGE

AIC0005

This gauge indicates the approximate fuel level in the tank. The gauge may move slightly during brak- ing, turning, acceleration, or going up or down hills. The gauge needle remains in approximately the same position even when the ignition key is turned OFF. The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge registers E (empty).

Instruments and controls 2-5

Z X

WARNING/INDICATOR LIGHTS AND CHIMES

Checking bulbs Apply the parking brake, fasten seat belts, and turn the ignition key to ON without start- ing the engine. The following lights come on and stay on until the engine is started:

The following lights come on briefly and then go off: ABS or If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the 2-6 Instruments and controls

system repaired promptly.

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call an autho- rized NISSAN dealer. The oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See ‘‘Engine oil’’ in the ‘‘Do-it-yourself’’ section of this manual.

AIC1093

CAUTION

Running the engine with the oil pres- sure warning light on could cause seri- ous damage to the engine almost im- mediately. Turn off the engine as soon as it is safe to do so.

Charge warning light

If the light comes on while the engine is running, it may indicate something wrong with the charging system. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light re-

Z X

mains on, see an authorized NISSAN dealer immediately.

CAUTION

Do not continue driving if the belt is loose, broken or missing.

Low fuel warning light

This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).

Door ajar warning light

This light comes on when any of the doors are not closed securely while the ignition key is ON.

Seat belt warning light and chime

The light and chime remind you to fasten your seat belts. If the driver’s seat belt is NOT securely fastened when the ignition key is turned to ON or START, the chime sounds for approximately 6 seconds and the light illuminates.

in the ‘‘Seats, re- Refer to ‘‘Seat belts’’ straints and supplemental air bag systems’’ section of this manual for precautions on seat belt usage.

Supplemental air bag warning light

When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the Air Bag Supple- mental Restraint System is operational. If any of the following conditions occur, the supplemental air bag system needs servic- ing and your vehicle should be taken to an authorized NISSAN dealer: 1. The supplemental air bag warning light does not come on for 7 seconds and then turn off as described above.

2. The supplemental air bag warning light flashes intermittently, or remains on after 7 seconds.

3. The supplemental air bag warning light

does not come on at all.

Under these conditions, the Air Bag Supple- mental restraint system may not function properly. For additional details, see ‘‘Supple-

in the ‘‘Seats, re- mental restraint system’’ straints and supplemental air bag systems’’ section of this manual.

WARNING

is on,

If the supplemental air bag warning light the supplemental air bag will not operate in an accident.

it could mean that

Low washer fluid warning light

This light comes on when the washer fluid is at a low level. Add washer fluid as neces- sary. See the ‘‘Do-it-yourself’’ section of this manual.

Brake warning light

functions for both the parking

This light brake and the foot brake systems. When the ignition key is in the ON position, the light comes on when the parking brake is applied, and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:

Instruments and controls 2-7

Z X

1. Check the brake fluid level. Add brake fluid in the

as necessary. See ‘‘Brake fluid’’ ‘‘Do-it-yourself’’ section of this manual.

2. If the brake fluid level is correct, have the warning system checked by an autho- rized NISSAN dealer.

WARNING

c Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your ve- hicle towed.

c Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel.

c If the brake fluid level is below the minimum mark on the brake fluid reservoir, do not drive until the brake system has been checked at an au- thorized NISSAN dealer.

2-8 Instruments and controls

ABS or

Anti-lock brake warning light

If the light comes on while the engine is running, it may indicate something is wrong with the anti-lock portion of the brake sys- tem. Have the system checked by an autho- rized NISSAN dealer. If a malfunction occurs in the system, the anti-lock function turns off, but the brakes continue to operate normally. If the light comes on while you are driv- ing, contact an authorized NISSAN dealer for repair.

Overdrive off indicator light

This light comes on during driving when the overdrive switch is pressed to prevent over- drive operation. The O/D OFF indicator light comes on for two seconds each time the ignition key is turned ON. This shows the light is function- ing properly. If the O/D OFF indicator light blinks for approximately 8 seconds after coming on for 2 seconds, have an authorized NISSAN

dealer check the transmission and repair it if necessary. The automatic transmission is equipped with an electronic Fail-Safe mode. This sys- tem allows the vehicle to be driven even in the event of damage to the electrical cir- cuits. If this occurs, the gears automatically engage and lock into third gear. NOTE: See ‘‘Fail-safe’’ in the ‘‘Starting and driving’’ section of this manual before visit- ing an authorized NISSAN dealer.

Turn signal/hazard indicator lights

The appropriate light flashes when the turn signal lever is activated. Both lights flash when the hazard switch is turned on.

High beam indicator light

This light comes on when the headlight high beam is on and goes out when the low beam is selected.

Cruise indicator light

The light comes on while the vehicle speed is controlled by the cruise control system. If the

Z X

CRUISE indicator blinks, have the system checked by an authorized NISSAN dealer. Key reminder chime The chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime A chime sounds when the driver’s door is opened if the headlight control switch is turned on (ignition switch is turned OFF). The chime will not sound when the Auto- lamp (if so equipped) shut-off delay is acti- vated. Refer to the ‘‘Autolamp Switch’’ in- structions later in this section. Turn the headlight control switch to OFF when you leave the vehicle. Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard.

Malfunction indicator (MIL)

light

If the malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control problem. The malfunction indicator light may also come on steady or blink if the fuel filler cap has not been closed tightly or if the fuel tank is nearly empty. Check to make sure the fuel cap is secure and that you have at least three gallons (14 liters) of fuel in the fuel tank. After driving for a while, the light should remain off if no other potential emission control system problem exists. Operation The malfunction indicator light will come on in one of two ways: c Malfunction indicator light on steady - An emission control system malfunction has been detected. Have the vehicle in- spected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

c Malfunction indicator light blinking - An engine misfire has been detected which may damage the emission control sys- tem. To reduce or avoid emission control system damage: a) do not drive at speeds above 45 MPH

b) avoid hard acceleration or decelera-

(72 km/h).

tion.

c) avoid steep uphill grades. d) if possible, reduce the amount of cargo

being hauled or towed.

The malfunction indicator light may stop blinking and come on steady. Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your ve- hicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Instruments and controls 2-9

Z X

THEFT WARNING (if so equipped)

c When the

that

button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder the doors are already locked. The horn may or may not beep once. Refer to ‘‘silencing the horn beep fea- ture’’ later in this section.

IC0005

The theft warning system provides audio and visual alarm signals if parts of the vehicle are disturbed. How to activate the theft warning system 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close all doors and the hood. 4. Push the

button on the multi-remote controller. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.

2-10 Instruments and controls

The system can be activated even if the windows are open. 5. Confirm that

the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then begins to flash once every three seconds. The system is now activated. If, during this 30-second time period, the door is unlocked by the key or the multi-remote controller, or the ignition key is turned to ACC or ON, the system will not activate. If the key is turned slowly when locking the door, the system may not activate. Furthermore, if the key is turned exces- sively to the unlock position, the system may be deactivated when the key is re- moved. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.

Even when the driver and/or passengers are in the vehicle, the system will acti- vate with all doors, hood and trunk lid locked and ignition key off. Turn the ignition key to ACC or ON to turn the system off. Theft warning system operation The theft warning system emits the follow- ing alarm: c The headlights and tail lights flash and the horn sounds intermittently. In addi- tion, the starter motor does not operate. c The alarm automatically turns off after two to three minutes. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking a door with the key or by pressing the button on the multi- remote controller.

The alarm is activated when: c a door is unlocked or opened without using the key or the multi-remote control- ler. This includes unlocking the doors with the inside door lock switch.

c the hood is opened.

Z X

c the ignition is placed into the ACC, ON, or START position without the key in the ignition.

How to stop the alarm The alarm stops only by unlocking a door with the key or by pressing the button on the multi-remote controller. The alarm does not stop if the ignition key is turned to the ACC or ON position.

The hazard lights will quickly flash three times to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered. If the system does not operate as de- scribed above, have it checked by an authorized NISSAN dealer.

AIC1037

Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the multi-remote control- ler. The instructions are on the back of the multi-remote controller. To deactivate: Press and hold the

and

buttons for at least two seconds.

The hazard lights will quickly flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the

and buttons for at least two seconds once

more.

Instruments and controls 2-11

Z X

WINDSHIELD WIPER AND WASHER SWITCH

and obscure your vision, which may lead to an accident. Warm the wind- shield with the defroster before you wash the windshield.

AIC0561

AIC0559

To operate the wipers intermittently, adjust the knob between the S (slow) and F (fast) positions. For continuous operation, select LO or HI. To operate the washer, press on the end of the wiper knob. For more washer fluid, push and hold the end of the wiper knob. The wipers cycle a few times when the washer is activated. The washer operates in any of the wiper positions.

2-12 Instruments and controls

CAUTION

following could damage

The washer system: c Do not operate the washer continu-

the

ously for more than 30 seconds.

c Do not operate the washer if the

reservoir tank is empty.

WARNING

In freezing temperatures the washer solution may freeze on the windshield

Z X

REAR WINDOW WIPER AND WASHER SWITCHES

REAR WINDOW DEFOGGER SWITCH

HEADLIGHT CONTROL SWITCH

AIC1056

AIC1057

AIC1073

Push and hold the rear washer switch to operate the rear washer. The wiper cycles continuously until the switch is released. Push the rear wiper switch to operate the wiper. The wiper cycles intermittently. Push again to cancel.

CAUTION

c Do not operate the washer continu-

ously for more than 30 seconds.

c Do not operate the washer if the

reservoir tank is empty.

To defog the rear window glass, start the engine and push the switch on. The indica- tor light on the switch comes on. Push the switch again to turn the defogger off. The rear window defogger switch is also used to defrost, defog, or de-ice the power outside heated mirrors (if so equipped). It automatically turns off in approximately 15
minutes.

CAUTION

When cleaning the inner side of the window, be careful not to scratch or damage the rear window defogger.

position:

position:

Lighting Turn the dial to the The front parking, side marker, tail, license plate and instrument lights come on. Turn the dial to the Headlights come on and all of the previously listed lights remain on. To select the high beam, push the turn signal lever away from you. The lever latches in place. Pull it back to select the low beam. To turn the interior lights on push the head- light switch. The interior lights come on. Instruments and controls 2-13

Z X

Push the headlight switch again to turn the interior lights off. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The day- time running lights operate with the head- light switch in the OFF position or in the position. Turn the headlight switch to position for full illumination when

the driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is turned OFF.

WARNING

When the daytime running light system is active, tail lights on your vehicle will not be on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

2-14 Instruments and controls

AUTOLAMP SWITCH (if so equipped)

AIC1058

If

Shut-off delay The length of time the headlights stay on after the ignition is turned to OFF depends on whether the switch is in the AUTO1 or AUTO2 position. the switch is in the AUTO1 position, then the headlights stay on for less than 1 minute after the ignition is turned OFF. If the switch is in the AUTO2
position, the headlights stay on approxi- mately 3 minutes after the ignition is turned OFF. To turn the autolamp system off, turn the switch to the OFF,

position.

, or

The autolamp system allows the headlights to be set so they turn on and off automati- cally. The autolamp system can turn on the headlights automatically when it is dark, turn off the headlights when it is light, and keep the headlights on for up to three minutes after you turn the key to OFF. To set the autolamp system: 1. Make sure the headlight switch is in the

AUTO1 or AUTO2 position. 2. Turn the ignition key to ON. 3. The autolamp system automatically turns

the headlights on and off.

Z X

TURN SIGNAL SWITCH

CORNERING LIGHT

AIC1087

AIC0560

AIC0102

Be sure you do not put anything on top of the photo sensor located in the top left side of the instrument panel. The photo sensor controls the autolamp; if it is covered, the photo sensor reacts as if it is dark out and the headlights will illumi- nate.

Turn signal Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signal cancels automati- cally. Lane change signal To indicate a lane change, move the lever up or down to the point where the light begins to flash, but the lever does not latch. Passing signal Pulling the lever toward you turns the head- light high beam on. Release it and the headlight high beam goes off.

The cornering light provides additional illu- mination toward the turning direction. The light on the turning direction side comes on when a turn is signaled with the headlights on.

Instruments and controls 2-15

Z X

INSTRUMENT BRIGHTNESS CONTROL

HAZARD WARNING FLASHER SWITCH

slowly that your vehicle might be- come a hazard to other traffic.

c Turn signals do not work when the hazard warning flasher lights are on.

The flashers can be actuated with the igni- tion switch either OFF or ON. Some state laws may prohibit the use of the hazard warning flasher switch while driving.

AIC1059

AIC1060

The instrument brightness control operates when the light switch is in the or position, or when the autolamp system

is operating. Pressing the side of the switch bright- ens the instrument panel lights; pressing the side of the switch dims the instrument

panel lights.

2-16 Instruments and controls

(hazard) switch to warn other Push the drivers when you must stop or park under emergency conditions. All turn signal lights flash. Press the switch again to turn the hazard warning flashers off.

WARNING

c When stalled or stopped on the road- way under emergency conditions, move the vehicle well off the road.

c Do not use the switch while moving on the highway unless unusual cir- cumstances force you to drive so

Z X

CIGARETTE LIGHTER AND ASHTRAY (accessory)

AIC1074

AIC1075

The cigarette lighter element is an acces- sory. A genuine NISSAN cigarette lighter or equivalent can be purchased from an autho- rized NISSAN dealer. The cigarette lighter operates when the ignition switch is in the ACC or ON position. Push the lighter in all the way. When the lighter is heated, it springs out. Return the lighter to its original position after use.

The utility tray has a rubber mat that may be removed for cleaning. The ashtray is an accessory. A genuine NISSAN ashtray or equivalent can be pur- chased from an authorized NISSAN dealer. The ashtray fits in the utility box. Do not use the utility box as an ashtray. Use only a genuine NISSAN ashtray or equivalent. Pull on the lid of the ashtray to remove it for disposing of ashes.

CAUTION

The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.

WARNING

The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation.

Instruments and controls 2-17

Z X

REAR POWER POINT

CUP HOLDER

AIC1064

AIC1065

The rear power point is located on the driver’s side trim panel of the second row seat behind the side door. Open the cover to gain access to the power point. Use the power point to plug in electrical equipment such as a cellular telephone, CB radio, etc. Follow the installation instruc- tions included with your electrical equip- ment. When not in use, always close the power point cover.

CAUTION

When using the power point: c Maximum load of any electrical equipment should not exceed 10
amps.

c Be sure to turn off any electrical equipment when not in use. Leaving electrical equipment on for extended periods can discharge your battery.

To use the cup holder, pull out. To store the cup holder, push it back in. The cup holder can be adjusted to fit smaller cups by pushing the arms in. The arms have three detents and then return to the fully open position.

WARNING

The driver should not pull out the cup holder or remove or insert cups into the cup holder while driving in order that full attention may be given to the driv- ing operation.

2-18 Instruments and controls

Z X

CAUTION

c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liq- uid is hot, it can scald you or your passenger.

c Use only soft cups in the cup holder. Hard objects can injure you in an accident.

AIC1076

AIC1077

Second row cup holder Vehicles equipped with second row bucket seats have a cup holder attached to the side of the seat.

Vehicles equipped with a second row bench seat have a cup holder attached to the front center of the seat. Pull the cup holder out from the seat to use it. The cup holder can be adjusted to fit smaller cups by pushing in the arms. The arms have three detents and then return to the fully open position.

Instruments and controls 2-19

Z X

MAP POCKETS

OVERHEAD STORAGE COMPARTMENT

AIC1078

ARS1249

AIC1095

A map pocket is located on the right hand side of the instrument panel and on the back of the passenger seat. The map pockets can be used to store maps.

Some vehicles are equipped with an over- head storage compartment. Push to open the storage compartment. Push again to close the storage compartment.

2-20 Instruments and controls

Z X

POWER WINDOWS

WARNING

c Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.

c Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents.

AIC1079

AIC1080

The main switch (on the driver side) opens or closes the driver’s, and passenger’s win- dows, and (if so equipped) rear vent win- dows. To open the window, press the switch down. To close the window, lift the switch up. The power windows operate when the igni- tion key is in the ON position, or for 15
minutes after the ignition key is turned to the OFF position. If the driver’s or passenger’s door is opened during this 15 minute period, power to the windows is cancelled.

AUTOMATIC POWER WINDOW SWITCH To fully open the driver side window, press down firmly on the switch and release it; you do not need to hold the switch down. The window automatically opens all the way. The automatic feature can be interrupted before the window is fully open by briefly lifting up on the switch as the window moves down.

Instruments and controls 2-21

Z X

SUNROOF (if so equipped)

AIC1081

AIC1066

Locking passenger’s window When the power window lock-out button is pushed in, the passenger’s window cannot be opened or closed. Push the power win- dow lock-out button again to cancel this feature. The passenger side switch opens or closes the passenger window only. To open the window, press the switch down. To close the window, lift the switch up.

2-22 Instruments and controls

The sunroof operates when the ignition key is in the ON position, or for 15 minutes after the ignition key is turned to the OFF posi- tion. If the driver’s or passenger’s door is opened during this 15 minute period, power to the sunroof is cancelled. NOTE: If the battery is discharged or is discon- nected, the sunroof may not operate cor- rectly, and must be reset. To reset a fully or partially open sunroof: 1. Push and hold the UP/CLOSE side of the sunroof switch until the sunroof closes,

and tilts up to the fully open position, then release the switch.

2. Push and hold the DOWN/OPEN side of the switch until the sunroof lowers com- pletely. The sunroof is now reset and should operate correctly.

To reset a fully or partially tilted, or closed sunroof: 1. Push and hold the UP/CLOSE side of the the sunroof stops

sunroof switch until tilting up, then release the switch.

2. Push and hold the DOWN/OPEN side of the switch until the sunroof lowers com- pletely. The sunroof is now reset and should operate correctly.

Sliding the sunroof To open the roof, push and hold the OPEN side of the switch. To close the roof, push and hold the CLOSE side. Tilting the sunroof To tilt up, first close the sunroof, then push the UP side of the switch. To close the sunroof, push the DOWN side of the switch.

Z X

Sun shade Open and close the sun shade by sliding it forward or backward. The shade opens when the sunroof opens, but it must be closed manually.

WARNING

c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.

c Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is closing.

CAUTION

c Remove water drops, snow,

ice or sand from the sunroof before opening. c Do not place any heavy object on the

sunroof or surrounding area.

MANUAL VENT WINDOWS

POWER VENT WINDOWS (if so equipped)

AIC0111

AIC1067

To open the manual vent windows, pull the rear portion of the latch toward you until it releases. To lock the window in the open position, push the latch rearward until you hear it latch. To close the windows, pull the latch toward you and push the rear portion of the latch toward the rear of the vehicle until you feel it latch.

Use the vent window switches on the driv- er’s side window controls to open and close the power vent windows. To open one of the power vent windows, press the switch down. To close the window, lift the switch up. The power vent windows operate when the ignition key is in the ON position, or for 15
minutes after the ignition key is turned to the OFF position. If the driver’s or passenger’s door is opened during this 15 minute period, power to the vent windows is cancelled.

Instruments and controls 2-23

Z X

INTERIOR LIGHTS

PERSONAL READING LIGHT

c When the switch is in the ON position, the interior light illuminates, whether any door is open or closed.

CAUTION

Leaving the interior light switch in the ON position for extended periods of time will result in a discharged battery.

LUGGAGE COMPARTMENT LIGHTS When the back door is opened, the luggage compartment light and the rear interior light illuminate. When the back door is closed, the lights go off.

AIC0053

The interior lights operate regardless of ignition key position. One interior light is located overhead near the front seats and one is overhead near the rear seat. The interior switches: c When the switch is in the OFF position, the interior light does not illuminate, re- gardless of door position.

lights have three-position

c When the switch is in the center O posi- tion, the light illuminates when a door is opened.

2-24 Instruments and controls

AIC1088

The driver’s side, second and third row seating positions have a personal reading light located in the overhead trim panel. To turn the light on, press once on the right-hand side of the light cover. To turn the light off, press again on the right-hand side of the light cover.

Z X

MAP LIGHTS

AIC1097

To turn on the map lights, press the switches. To turn them off, press the switches again.

ILLUMINATED ENTRY SYSTEM

The interior lights, the cargo light, the glove box light, the stepwell lights near the sliding doors and on the front doors, and the foot- well lights near the driver’s and front pas- senger’s feet illuminate when the front or sliding doors are opened. Once the doors are closed, these lights gradually dim to off within 30 seconds or turn off immediately when the key is turned to the ON position. Battery saver If the vehicle doors are not fully closed and the interior lights remain illuminated, they eventually turn off automatically to prevent the battery from becoming discharged. If the interior lights are left in the ON position, with all doors closed, they will automatically turn off after approximately 30 minutes. Lights that illuminate when the front or sliding doors are opened turn off after approxi- mately 30 minutes. Lights that illuminate when the back door is opened turn off after approximately 60 minutes. Vanity mirror lights are not part of the battery saver system. If the personal reading lights are left on after the key is removed from the ignition, they will automatically turn off after approxi- mately 30 minutes.

STORAGE COMPARTMENT FOR GARAGE DOOR TRANSMITTER (if so equipped)

AIC1089

Some vehicles are equipped with an addi- tional storage compartment in the map light unit. This storage compartment has been specially designed to hold some garage door transmitters. Some transmitters may not fit. When properly installed, the garage door transmitter can be activated while it is within the storage compartment.

Instruments and controls 2-25

Z X

AIC1090

AIC1091

AIC1092

To install your transmitter, follow the num- bered instructions in the illustrations.

Once the garage door transmitter is in- stalled, close the storage compartment door. Press the button on the center of the storage compartment door to operate the garage door transmitter.

2-26 Instruments and controls

Z X

door, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

INTEGRATED HomeLinkT UNIVERSAL TRANSCEIVER (if so equipped) The Integrated HomeLinkT Universal Trans- ceiver provides a convenient way to consoli- date the functions of up to three individual hand-held transmitters into one built-in de- vice. c The Integrated HomeLinkT Universal Transceiver will operate garage doors, gates, home/office lighting systems and security systems by storing and transmit- ting the programming information of your current hand-held transmitters.

c The Integrated HomeLinkT Universal Transceiver is built-in and powered by your vehicle’s battery and charging sys- tem. No separate batteries are necessary.

WARNING

Do not use this Integrated HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by federal safety standards (these standards be- came effective for models manufac- tured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse the

AIC1069

PROGRAMMING THE HomeLinkT UNIVERSAL TRANSCEIVER

WARNING

During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.

Instruments and controls 2-27

Z X

Your vehicle’s engine should be turned off while programming your transmit- ter. The Integrated HomeLinkT Univer- sal Transceiver may not work with older garage door openers that do not meet current Federal Consumer Safety Standards.

1. Test the Integrated HomeLinkT Universal Transceiver by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3.

2. Clear all channels on the Integrated HomeLinkT Universal Transceiver by holding down both outside buttons (#1 & the red light begins to flash #3) until rapidly (approximately 20 seconds). Then release both buttons.

3. Select which of

the three Integrated HomeLinkT Universal Transceiver but- tons you want to program.

4. Hold your hand-held transmitter against the bottom surface of the Integrated HomeLinkT Universal Transceiver so that you can still see the red indicator light.

2-28 Instruments and controls

5. Press the desired button until the red indicator light flashes slowly. Do not re- lease the button. Continue holding and press the hand-held transmitter button through step 6.

on

the

6. Hold down both buttons until

light

Universal

the red Integrated indicator HomeLinkT Transceiver flashes rapidly (This may take 1 to 90
seconds). Then release both buttons. The rapid flashing means that the trans- ceiver has been successfully pro- grammed to match your hand-held trans- mitter. You can now use the Integrated HomeLinkT Universal Transceiver in- stead of your hand-held transmitter.

Note to Canadian users: Prior to 1992, D.O.C. regulations required many hand-held transmitters to stop trans- mitting after one or two seconds, even though you continue to hold down the but- ton. these hand-held transmitters, you should press and re-press the transmitter button every 2
seconds without ever releasing the Inte- grated HomeLinkT Universal Transceiver button. The indicator light on the Integrated HomeLinkT Universal Transceiver should

If you think you have one of

blink rapidly indicating a successful pro- gramming procedure. If it returns to the slow blink of program mode, continue to periodi- cally reactivate your hand-held transmitter until a successful programming procedure is indicated by the rapidly flashing indicator light. OPERATING THE TRANSCEIVER To operate, simply press the appropriate button on the Integrated HomeLinkT Univer- sal Transceiver. The red indicator light illu- minates while the signal is being transmit- ted. The effective transmission range of the Integrated HomeLinkT Universal Trans- ceiver may differ from your hand-held trans- mitter. PROGRAMMING PROBLEM DIAGNOSIS Be sure to keep your original hand-held transmitter for possible reprogramming if necessary. c Make sure batteries in the hand-held

transmitter are fully charged.

c Hold your hand-held transmitter against the bottom surface of the Integrated HomeLinkT Universal Transceiver so

Z X

that you can still see the red indicator light.

c Hold buttons for duration of the program-

ming without interruption.

c Rotate your hand-held transmitter end- over-end and program again. For best results, place the end opposite the bat- tery compartment against the Integrated HomeLinkT Universal Transceiver when programming.

AIC1070

ROLLING CODES If your hand held transmitter appears to train to the Integrated HomeLinkT Universal Transceiver, but does not open your garage door, and your garage door opener was manufactured after 1995, your garage door opener may have a Code Protected or Rolling Code feature. This type of system will change the code of your garage door opener every time you open or close your garage door. To determine if you have one of these systems, depress the button on the Inte- grated HomeLinkT Universal Transceiver

that you have just programmed. If the LED on the HomeLinkT Universal Transceiver flashes rapidly for 1 to 2 seconds, then remains on, your garage door opener has a rolling code system. To operate your rolling code garage door opener from your Integrated HomeLinkT Universal Transceiver, follow these steps: 1. Program your hand held transmitter to the Integrated HomeLinkT Universal Transceiver by following the procedures outlined previously (if not yet pro- grammed).

2. Program your garage door opener re- ceiver to recognize the Integrated HomeLinkT Universal Transceiver (The Integrated HomeLinkT Universal Trans- ceiver follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed): a) Remove the cover panel from your garage door opener receiver. The re- ceiver should be located by the ga- rage door opener motor.

b) Locate the training button on the ga- rage door opener receiver. The exact location and color of the button may Instruments and controls 2-29

Z X

vary by garage door opener brand. If you have difficulty locating the training button, reference your garage door opener manual. If you have difficulty programming door opener equipped with a rolling code system to recognize the Integrated HomeLinkT Universal Transceiver with the Rolling Code feature, call NISSAN Consumer Affairs Department.

garage

your

c) Press the training button on the ga- rage door opener receiver for 1 to 2
seconds.

the

depress

d) Return to the Integrated HomeLinkT Universal Transceiver in the vehicle, and programmed HomeLinkT button for the duration of the fast blink on the Integrated HomeLinkT Universal Transceiver (1
to 2 seconds). Release the button, and repress to confirm that the system has trained.

e) Your garage door opener should now recognize your Integrated HomeLinkT Universal Transceiver. You may use either your Integrated HomeLinkT Uni- versal Transceiver or your original

2-30 Instruments and controls

hand held transmitter to open your garage door.

the channels of

CLEARING THE PROGRAMMING INFORMATION Should you sell your vehicle, be sure to clear the Integrated HomeLinkT Universal Transceiver. To clear the channels, simultaneously hold down the outside two buttons (#1 & #3) until the red indicator light begins to flash rapidly (ap- proximately 20 seconds). This will clear all three buttons. Individual buttons cannot be cleared, but can be reprogrammed at any time by following the programming proce- dures described previously. IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was programmed into the Integrated HomeLinkT Universal Transceiver as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those devices. When your vehicle is recovered, you will have Integrated

to reprogram the

HomeLinkT Universal Transceiver with your new transmitter information. FFC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author- ity to operate the device. DOC: ISTC 1763K1313
FCC I.D.: CB2V67690

Z X

3 Pre-driving checks and adjustments

Key .........................................................................3-2
Door locks ..............................................................3-2
Manual door lock....................................................3-3
Child safety sliding door lock .................................3-6
Power door lock (if so equipped)...........................3-7
Multi-remote control system (if so equipped).........3-9
Battery replacement .............................................3-11
Illuminated entry system ......................................3-12
Hood release........................................................3-12
Glove box .............................................................3-13
Front seat convenience net .................................3-14
Rear door lock......................................................3-15
Cargo net (if so equipped) ...................................3-16

Parcel shelf (if so equipped) ................................3-17
Luggage rack (if so equipped) .............................3-19
Fuel filler lid and cap............................................3-20
Tilting steering wheel ...........................................3-21
Memory driver seat and mirrors (if so equipped) .............................................................3-21
Multi-remote controller system entry....................3-21
Memory driver seat and mirror buttons................3-22
Outside mirror control...........................................3-23
Outside mirrors.....................................................3-24
Inside mirror .........................................................3-24
Vanity mirror.........................................................3-24

Z X

KEY

DOOR LOCKS

APD1042

A key number plate is supplied with your key. Record the key number and keep it in a safe place (such as your wallet), NOT IN THE CAR. A key number plate is supplied with your key. Keep the plate in a safe place. NISSAN does not record key num- bers so it is very important to keep track of your key number plate. A key number is necessary only when you have lost all vehicle keys and do not have one to duplicate. If you still have a key, this key can be duplicated by an authorized NISSAN dealer or locksmith shop.

3-2 Pre-driving checks and adjustments

Two keys are supplied with your vehicle — one has a plastic head and one is all metal. Both keys perform the same functions.

WARNING

c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.

c Before opening any door, always look for and avoid oncoming traffic. c Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.

CAUTION

c Always use the door handle to open or close the sliding doors. Do not attempt to open or close the doors by merely placing your hand on the door edge or door slide roller, as this may cause injury.

Z X

c Always be sure that hands and feet are clear of the door frame to avoid injury while closing a sliding door.

c When opening a sliding door on a slope, ensure that it is fully open and that it does not close by itself.

APD1053

MANUAL DOOR LOCK To lock a front door from the outside, turn the key toward the front of the vehicle. To unlock, turn it toward the rear.

Pre-driving checks and adjustments 3-3

Z X

APD1054

Locking the doors without the key To lock a front door from inside the vehicle, push the door lock knob in, then close the door. When locking the door this way, be certain not to leave the key inside the vehicle.

3-4 Pre-driving checks and adjustments

Z X

APD1055

Sliding door lock To lock a sliding door from inside the ve- hicle, press the door lock rocker switch on the side marked L. To unlock, press the rocker switch on the side marked U. The driver side sliding door cannot be fully opened when the fuel door is open.

Pre-driving checks and adjustments 3-5

Z X

APD1056

When the lever is in the LOCK position, the sliding doors can be opened only from the outside.

CHILD SAFETY SLIDING DOOR LOCK Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle.

3-6 Pre-driving checks and adjustments

Z X

APD1074

APD1075

POWER DOOR LOCK (if so equipped) Operating the lock-unlock switch locks or unlocks all doors. If the power door lock switch is pressed when a sliding door is open, the sliding door automatically locks when it is closed.

Pre-driving checks and adjustments 3-7

Z X

To lock all doors from inside the vehicle, push the door lock knob in, then close the door. When locking the doors this way, be certain not to leave the key inside the ve- hicle. All doors automatically unlock if the key is in the ignition and a door is open.

3-8 Pre-driving checks and adjustments

APD1054

APD1057

Selective unlock Turning the door key one time to the rear of the vehicle unlocks the corresponding door. From that position, returning the key to Neutral (where the key can only be removed and inserted) and turning it to the rear again within 5 seconds unlocks all doors. Turning the door key to the front of the vehicle locks all doors. The selective unlock function and locking all doors can be operated from the driver, passenger and rear door.

Z X

MULTI-REMOTE CONTROL SYSTEM (if so equipped)

It is possible to lock/unlock all doors, turn the interior lights on or off, and activate the panic alarm by using the remote controller from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors and leaving it. The remote controller can operate at a distance of approximately 30 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle. As many as four remote controllers can be used with one vehicle. For more information concerning the purchase and use of addi- tional remote controllers, contact an autho- rized NISSAN dealer.

CAUTION

Listed below are conditions or occur- rences which will damage the remote controller: c Do not allow the remote controller to

become wet.

c Do not drop the remote controller. c Do not strike the remote controller

sharply against another object.

c Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).

Locking doors 1. Close all doors. 2. Push the controller.

button on the multi-remote

3. All doors lock. 4. The parking lights flash twice and the horn chirps once to verify all doors are locked.

Unlocking doors For memory seat and mirror information see ‘‘Memory driver seat and mirrors’’ later in this section. 1. Push the

button on the multi-remote controller. Only the driver door unlocks. Parking lights flash once.

2. The interior lights come on and stay on

for 30 seconds.

3. Push the

button on the multi-remote controller again within five seconds. The

passenger door, sliding doors, and the rear door unlock.

The interior lights can be turned off without waiting 30 seconds by either turning the ignition to ON or locking the doors with the multi-remote controller. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the panic alarm to call attention as follows: 1. Push and hold the

button on the least one full

remote controller for at second.

2. The theft warning alarm (horn) sounds and the headlights and tail lights flash for 30 seconds.

3. The panic alarm stops when: c it has run for 30 seconds, or c the c the

or the button is pressed, or button is released and re-pushed.

Pre-driving checks and adjustments 3-9

Z X

The hazard lights will quickly flash three times to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered.

AIC1037

Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the multi-remote control- ler. The instructions are on the back of the multi-remote controller. To deactivate: Press and hold the

and

buttons for at least two seconds.

The hazard lights will quickly flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the

and two seconds

buttons for at

least

once more. 3-10 Pre-driving checks and adjustments

Z X

BATTERY REPLACEMENT

Replace the battery as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one. Insert the batteries as illustrated above. Recommended battery: Panasonic CR2025, 3V or equivalent.

APD1087

3. Close the lid securely. 4. Press the

button, then the

button two or three times to check the multi- remote controller operation.

If the batteries are removed for any rea- son other than replacement, perform step 4. c An improperly disposed battery can hurt the environment. Always conform to local regulations for battery disposal. c The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry.

c The operational range of the multi- remote controller extends to approxi- mately 30 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry