1998 Nissan Quest Owners Manual

ditions. You could be burned or se- riously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

c Fuel may be under pressure. Turn the cap one-half turn, and wait for any ‘‘hissing’’ sound to stop to prevent fuel from spraying out and possible personal injury. Then remove the cap. c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refuel- ing may cause fuel overflow, result- ing in fuel spray and possibly a fire. c Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper op- eration of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunc- tion and possible injury.

c Never pour fuel into the throttle body

to attempt to start your vehicle.

Z X

TILTING STEERING WHEEL

OUTSIDE MIRROR CONTROL

APD0812

APD0808

Push the lock lever down and adjust the steering wheel up or down to the desired position. Pull the lock lever up firmly to lock the steering wheel in place. Gently pull down on the wheel to be sure it is properly locked.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

Electric control type The outside mirrors operate only when the ignition switch is in the ACC or ON position. Move the switch to select the right or left side mirror, then adjust using the control lever.

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could

cause an accident. Use the inside mir- ror or glance over your shoulder to properly judge distances to other ob- jects.

The electric control type outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. Press the rear window defogger switch to activate the heating func- tion. Press the switch again to deactivate, or it automatically turns off in approximately 15
minutes.

Pre-driving checks and adjustments 3-17

Z X

OUTSIDE MIRRORS

INSIDE MIRROR

PD1183M

M008

PD1006M

Push the outside mirrors backward to fold them.

The night position reduces glare from the headlights of vehicles behind you at night.

WARNING

Use the night position only when nec- essary, because it reduces rear view clarity.

Manual control type The outside mirror can be moved in any direction for a better rear view.

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mir- ror or glance over your shoulder to properly judge distances to other ob- jects.

3-18 Pre-driving checks and adjustments

Z X

VANITY MIRROR

AIC0563

Your vehicle may be equipped with a driver or passenger side vanity mirror. If the vanity mirror on your vehicle has a cover, access the mirror by pulling the sun visor down and lifting the cover up. Some vanity mirrors illuminate when the mirror cover is opened.

Pre-driving checks and adjustments 3-19

Z X

MEMO

3-20 Pre-driving checks and adjustments

Z X

4 Heater, air conditioner and audio systems

Ventilators ..............................................................4-2
Heater and air conditioner (manual) ......................4-3
Controls ..................................................................4-3
Heater operation ....................................................4-4
Air conditioner operation ........................................4-5
Air flow charts.........................................................4-7
Heater and air conditioner (automatic) (if so equipped) .............................................................4-10
Automatic operation .............................................4-11
Air control buttons ................................................4-11
Air conditioner and air recirculation .....................4-12
English/metric mode.............................................4-12
Rear seat heater and air conditioner (if so equipped) .............................................................4-13

Controls ................................................................4-13
Audio system........................................................4-14
AM-FM radio with cassette player .......................4-14
Tuning ..................................................................4-16
Adjusting tone quality...........................................4-17
Cassette tape operations .....................................4-18
Antenna ................................................................4-20
Compact disc (CD) player (if so equipped) .........4-21
Steering wheel controls........................................4-23
Rear audio controls..............................................4-24
CB radio or car phone..........................................4-25

Z X

VENTILATORS

AHA0590

AHA0591

Center ventilators Open, close and adjust the air flow direction of ventilators.

Side ventilators Open, close and adjust the air flow direction of ventilators.

: This symbol indicates a vent is closed when the vent switch is rotated down- ward.

: This symbol indicates a vent is open when the vent switch is rotated up- ward.

: This symbol indicates a vent is closed when the vent switch is moved to the left.

: This symbol indicates a vent is open when the vent switch is moved to the right.

4-2 Heater, air conditioner and audio systems

Z X

HEATER AND AIR CONDITIONER (manual)

WARNING

c The air conditioner cooling function operates only when the engine is running. c Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

c Positioning of the heater and air con- ditioner controls should not be done while driving, in order that full atten- tion may be given to the driving operation.

CONTROLS Fan control dial This dial controls fan speed. Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air. Air control buttons These buttons allow you to select the air flow outlets or turn the system off.

AHA1037

Air flows from center and side ventila- tors. Air flows from center and side ventila- tors and foot outlets. Air flows mainly from foot outlets. Air flows from defroster outlets and foot outlets. Air flows mainly from defroster outlets.

OFF button The OFF button shuts off the air supply to all outlets and stops all fan operations. Use the OFF button to prevent cold air from entering Heater, air conditioner and audio systems 4-3

Z X

the passenger compartment under cold out- side conditions before the engine is warmed up.

Air recirculation button

Fresh position (indicator light off): Outside air is drawn into the passenger compartment. Use this position for normal heater or air conditioner operation. Recirculate position (indicator light on): Interior air is recirculated inside the vehicle. Activate the air recirculation button when driving on a dusty road or to help keep out traffic fumes. Activate the air recirculation button for im- proved air conditioner performance under high temperature and high humidity conditions. If the system is operating in the

or mode, the system does not allow the

air recirculate mode to be selected.

CAUTION

Do not use the recirculation mode for long periods as it may cause the inte- rior air to become stale and the win- dows to fog up.

Air conditioner button Start the engine, move the fan control dial to the desired (one to four) position, select an air control button and push the air conditioner button to turn on the air conditioner. The indicator light comes on when the air condi- tioner is on. To stop the air conditioner, push the button again; the indicator light goes off. The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct most of the hot air to the floor outlets. Push the air recirculation button to the off position for normal heating. 1. Push the button in. 2. Turn the fan control dial to select speed.

3. Move the temperature control dial to the

desired position.

Ventilation This mode directs air to the side and center vents. 1. Push the 2. Turn the fan control dial to select speed. 3. Move the temperature control dial to the

button in.

desired position.

Defrosting or defogging This mode is used to defrost/defog the windows. 1. Push the 2. Turn the fan control dial to select speed. 3. Move the temperature control dial to the

button in.

desired position. When the button is pushed, the air conditioner automatically turns on to de- fog the windshield. The air recirculation mode automatically turns off to reduce window fogging. When the air condi- tioner indicator light does not illuminate

is selected,

4-4 Heater, air conditioner and audio systems

Z X

unless illuminated in the previously se- lected mode. However, the air condi- tioner operates to dehumidify if the out- side temperature is more than 40°F (4°C), whether or not the A/C button has been pressed. Manual selection and illu- mination of the A/C button does not override the automatic dehumidifying which occurs when

is selected.

Operating Tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves defrosting/defogging op- eration. Bi-level heating/cooling The bi-level mode directs air to the side and center vents and to the floor outlets. Bi-level is also a cooling mode when high sun load conditions are present with cool temperatures. With the A/C system in operation, this mode can be used to cool the passenger’s or driver’s feet under high temperature condi- tions. With the A/C system in operation under high temperature conditions, improved cooling

can be obtained by pushing the air recircu- lation button to the on position. Push the air recirculation button to the off position when heating is required. 1. Push the 2. Turn the fan control dial to the desired

button in.

position.

3. Move the temperature control dial to the

desired position.

Heating and defogging This mode heats the interior and defogs the windshield. 1. Push the 2. Turn the fan control dial to the desired

button in.

position.

3. Move the temperature control dial to the

desired position. When the button is pushed, the air recirculation mode automatically turns off. Outside air is drawn into the passen- ger compartment to improve the defog- ging performance.

Operating tips c Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater op- eration.

c To defog the side windows more effec- tively when in bi-level or ventilation mode, close the center vent and direct the side vents toward the side windows. c A slight delay may be experienced when changing air control buttons. This is not a problem, it is only the system motors and solenoids switching from one outlet to another.

AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (one to four) position, and select an air control button before pushing in the air conditioner button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the system operation. The air conditioner cooling function op- erates only when the engine is running. NOTE: When switching air flow outlets, the A/C system remains activated unless the Heater, air conditioner and audio systems 4-5

Z X

c After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.

c The air conditioning system should be operated for about ten minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c If the engine coolant temperature gauge exceeds the H (hot) position, turn the air conditioner off. See ‘‘If your vehicle over- heats’’ in the ‘‘In case of emergency’’ section for additional information.

A/C button is pressed again to turn it off. The indicator light on the A/C button re- mains illuminated unless the button is pressed to turn it off, or the OFF air control button is pressed. Cooling This mode is used to cool and dehumidify. 1. Push the 2. Turn the fan control dial to select speed. 3. Push the air conditioner button. The indi-

button in.

cator light comes on.

4. Move the temperature control dial to the

desired position.

c For quick cooling when the outside tem- perature is high, push the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal cooling.

c Opening the windows helps to vent heat

buildup when parked in the sun.

Dehumidified heating This mode is used to heat and dehumidify. 1. Push the air recirculation button to the off

position.

button in.

2. Push the 3. Turn the fan control dial to select speed. 4. Push the air conditioner button. The indi-

cator light comes on.

5. Move the temperature control dial to the

desired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify. 1. Push the 2. Turn the fan control dial to the desired

button in.

speed.

3. Move the temperature control dial to the

desired position. button is pushed, the air When the conditioner automatically turns on to de- fog the windshield, (however, the light does not illuminate unless illuminated in the previously selected mode) and the air recirculation mode automatically turns off.

Operating tips c Keep windows and sun roof closed while

the air conditioner is in operation.

4-6 Heater, air conditioner and audio systems

Z X

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recir- culation switch should always be in the off position for heating and defrosting.

AHA0801

Heater, air conditioner and audio systems 4-7

Z X

4-8 Heater, air conditioner and audio systems

AHA1044

Z X

Heater, air conditioner and audio systems 4-9

AHA0800

Z X

HEATER AND AIR CONDITIONER (automatic) (if so equipped)

WARNING

c The air conditioner cooling function operates only when the engine is running. c Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

AHA0592

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

c Positioning of the heater and air con- ditioner controls should not be done while driving, in order that full atten- tion may be given to the driving operation.

The Electronic Automatic Temperature Control (EATC) is located at the center of the instrument panel, above the radio. The EATC operates only when the ignition is

4-10 Heater, air conditioner and audio systems

turned to the ON position. The EATC maintains the temperature you select and controls the airflow for your com- fort. It also allows you to override the auto- matic operation with manual function selec- tor buttons. To turn the EATC on, push either the AU- TOMATIC button or any of the five function selector buttons: . To turn the EATC off, press the or OFF button. When you select AUTOMATIC, the system determines fan speed, airflow location and discharge air temperature. When one of the function selector buttons is pressed, your selection determines airflow location only. Fan speed and discharge air temperature remain automatic. You can override fan speed by rotating the vertical thumbwheel the

the extreme right of

located at

control panel. The display window indicates the status of the system. It shows the selected tempera- ture and AUTO when in the AUTOMATIC mode. (thumb- the fan speed when a wheel) control of

It also indicates manual

is shown.

Z X

AUTOMATIC OPERATION Push the AUTOMATIC button and select the desired temperature. The selected tempera- ture and AUTO show in the display window. The EATC heats or cools to achieve the set temperature. When in AUTOMATIC and weather conditions require heat, air is sent to the floor. However, a feature is included in the EATC to prevent blowing cold air to the floor if the engine coolant is not warm enough to allow heating. In three or four minutes the fan speed gradu- ally increases and airflow changes to the floor. If unique conditions exist, such as window fogging, the five override buttons allow spe- cific airflow selection. The thumbwheel al- lows you to adjust the fan speed to suit your needs. Temperature selection The button on the left side of the control panel is for temperature selec- tion. The side lowers the set tempera- ture, and the side raises the set tem- perature. Press and hold either side of the button to rapidly change the temperature setting in one degree increments to either 65°F (18°C) or 85°F (29°C). If you want

TEMP

side of

continuous maximum cooling, push the the TEMP button until 60°F (16°C) shows in the display window. The EATC cools at maximum and disregards the 60°F (16°C) setting until a warmer tempera- ture is selected. If you want continuous maximum heating, push the side of the TEMP button until 90°F (32°C) shows in the display window. The EATC provides maxi- mum heat regardless of the 90°F (32°C) setting until a cooler temperature is se- lected. Fan speed and thumbwheel Your EATC automatically adjusts the fan speed to the existing conditions. To control the fan speed yourself, use the thumbwheel located at the EATC control panel. Using the thumbwheel cancels the automatic fan speed control, and causes a to appear in the display window. Rotate the thumbwheel up for HI speeds and down for LO speeds. To return to auto fan control, press the AUTOMATIC button. AIR CONTROL BUTTONS Your EATC has five buttons which allow you to make special selections. The buttons are

the extreme right side of

grouped in the middle of the EATC panel and allow you to determine airflow location. Pressing any of the air control buttons changes airflow location only, and does not affect the ability of the system to control temperature or fan speed. Return to fully automatic operation by pushing the AUTO- MATIC button.

Push this button for airflow to the floor and in- windshield at the same time. The dicator light comes on, and the display window shows the set temperature.

Press this button to obtain maximum airflow to the windshield. Adjust the temperature setting as required for defrosting. The indicator light comes on, and the display window shows the set temperature. When the outside temperature is about 50°F (10°C) or above, the air is dehumidi- fied to prevent window fogging.

Push this button to select airflow through the The Heater, air conditioner and audio systems 4-11

instrument

registers.

panel

Z X

indicator light comes on, and the display window shows the set temperature. The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle. However, the air is not cooled regardless of the temperature setting.

Push this button to get air from the floor and instrument panel registers at the same time. indicator light comes on and the The display window shows the set temperature. Depending on the selected temperature, the air is automatically heated or cooled.

on to verify activation, and cooled air flows from the vents. Fan speed continues to be controlled by the EATC unless the fan speed thumbwheel is used to override. button to choose air recir- Press the culation. In this mode the EATC system recirculates the air inside the vehicle rather than drawing air from outside. Use this mode together with the air conditioner to rapidly cool the inside of the vehicle, or to dehumidify the air inside the vehicle.

Push this button to direct airflow to the floor. The indicator light comes on, and the display window shows the set temperature. The air cannot be cooled in the mode, only heated. AIR CONDITIONER AND AIR RE- CIRCULATION Activate the air conditioner in any of the override modes listed above by pressing the A/C button. The A/C indicator light comes 4-12 Heater, air conditioner and audio systems

AHA762

ENGLISH/METRIC MODE Switch from English to metric temperature display by simultaneously pressing the and A/C buttons and holding the thumbwheel in upper position (HI) for one second.

Z X

REAR SEAT HEATER AND AIR CONDITIONER (if so equipped)

To operate the rear seat heater and air conditioner, the engine must be running. The rear seat heater and air conditioner can be turned on and off from the front controls. If the rear seat fan control lever on the front panel is set to OFF, the rear heater and air conditioner is turned off. If it is set to any of the fan speed positions, air is discharged from the rear vents at the corresponding speed. When the rear seat fan control lever on the front panel is set to REAR, the rear seat passengers control their own fan speed. The rear seat air conditioner only works when the front seat air conditioner is operating.

turns the fan on and off, and

CONTROLS Fan control dial This dial controls fan speed. Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air. A slight delay in temperature change may be experienced while the climate control system adjusts the outlet air temperature. c On vehicles equipped with Electronic Au- tomatic Temperature Control (EATC), out-

AHA0555

let air temperature is automatically con- trolled when the rear seat fan control lever on the front panel is set to one, two, three, or four.

Vent switch The vent switch allows you to select air flow from the upper or lower vents. c A slight delay may be experienced when changing the vent selection. This is not a problem; the delay is only the system motors and solenoids switching from one outlet to another.

Heater, air conditioner and audio systems 4-13

Z X

AUDIO SYSTEM

To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Clock For information on setting the clock, refer to the section ‘‘Instruments and controls’’.

influences.

AM-FM RADIO WITH CASSETTE PLAYER Radio operation Push the VOL-PUSH ON knob to turn the radio on. Push the VOL-PUSH ON knob once more to turn the radio off. Turn the knob to adjust the volume. Inserting a cassette tape into the cassette player while the radio is on turns the radio off and turns the cassette player on.

Servicing air conditioning The air conditioning system in your NISSAN vehicle is charged with a refrigerant de- signed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants causes severe damage to your air conditioning system. See ‘‘Air condition- ing system refrigerant and lubricant recom- mendations’’ in the ‘‘Technical and con- sumer information’’ section of this manual. An authorized NISSAN dealer is able to service your environmentally ‘‘friendly’’ air conditioning system.

WARNING

The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done by an experienced technician with proper equipment.

4-14 Heater, air conditioner and audio systems

Z X

AHA0593

Heater, air conditioner and audio systems 4-15

Z X

TUNING

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

AUTO SET (if so equipped) Press AUTO SET while listening to the radio to activate the Auto Memory Store feature. When AUTO SET is depressed for less than three seconds, the display window momen- tarily indicates AUTO, and the radio seeks the first six strong stations for the respective band. The first six strong stations are then stored in order in memory buttons one through six. Only stations in the selected band are set, and the station seek begins from the last frequency stored in memory button six. If AM, FM, SCAN, TUNE, SEEK, AUTO SET, or a memory button is pushed while Auto Memory Store is operating, AUTO SET is canceled and AUTO OFF shows in the display window.

AHA0594

Z X

4-16 Heater, air conditioner and audio systems

SEEK tuning This feature on your radio allows you to automatically select strong frequency sta- tions up or down the frequency band. Press SEEK to select the next strong sta- tion up the frequency band. Press SEEK to select the next strong station down the frequency band. To change frequencies quickly, press and hold either side of the SEEK button. SCAN tuning Push SCAN to enter the scan tuning mode. The radio searches up the frequency band, stopping and playing each strong frequency station for five seconds. This continues until the SCAN button is pushed a second time or a different tuning function is selected. The AM or FM1 or FM2 symbol in the display window flashes while each station is being played. AM/FM Press the AM/FM button to select the de- sired band: AM, FM1, or FM2. The stereo indicator shows in the display window dur- ing FM stereo reception. When the stereo broadcast signal is weak, the radio auto-

matically changes from stereo to monaural reception. Station memory operations Your radio comes equipped with six memory buttons, which are used to preset up to six AM stations and 12 FM stations. If NOTE: the vehicle’s battery is discon- nected, the memory buttons need to be reset. To set the memory buttons: 1. Select the desired band (AM, FM1, or

FM2) by pressing the AM/FM button.

2. Tune to the desired frequency. 3. Press one of the memory buttons and hold the button in. The sound mutes out for about two seconds, then returns. That station is now held in memory on that button.

the three steps above for each

Repeat memory button you want to set. The memory buttons also control the rear audio controls. Push memory buttons three and five simultaneously to turn the rear audio controls on. Push them again to turn the rear audio controls off. A headphone

symbol appears in the display window when the rear controls are activated. ADJUSTING TONE QUALITY BASS Bass control allows you to adjust the lower, bass frequencies to your preference. Push the BASS button either

or ; BASS and the setting indicator bar appear in the display window. Pressing the BASS button either in- creases or decreases the level of bass, as indicated by the number of bar segments showing in the display window. Following bass adjustment, the display win- dow shows the current setting for three seconds, then returns to the display prior to adjustment. TREB Treble control allows you to adjust higher, ence. Push the TREB button either

the treble frequencies to your prefer-

or

or ; TREB and the setting indicator bar appear in the display window. Pressing the TREB button either in- Heater, air conditioner and audio systems 4-17

or

Z X

creases or decreases the level of treble, as indicated by the number of bar segments showing in the display window. Following treble adjustment, the display window shows the current setting for three seconds, then returns to the display prior to adjustment. BAL the Balance control allows you to adjust sound distribution between the right and left speakers. Push the BAL button either

to shift

or ; BAL and the setting indicator bar appear in the display window. Press the BAL button to shift the sound to the right speakers. The single indicator bar moves to the right of the display window. Press the BAL button the sound to the left speakers. The single indi- cator bar moves to the left of the display window. When the indicator bar is in the center position the sound is equally distrib- uted between the right and left speakers. Following balance adjustment, the display window shows the current setting for three seconds, then returns to the display prior to adjustment. 4-18 Heater, air conditioner and audio systems

FADE Fader control allows you to adjust sound distribution between the front and rear speakers. Push the FADE button either

or ; FADE and the setting indicator bar appear in the display window. Press the FADE button to shift the sound to the front speakers. The single indicator bar moves to the right of the display window. Press the FADE button to shift the sound to the rear speakers. The single indicator bar moves to the left of the display window. When the indicator bar is in the center position the sound is equally distrib- uted between the front and rear speakers. Following fader adjustment, the display win- dow shows the current setting for three seconds, then returns to the display prior to adjustment. CASSETTE TAPE OPERATIONS Turn the ignition key to ACC or ON, then insert the cassette tape into the tape door by lightly pushing it. Because of the power loading feature, the cassette tape is auto- matically pulled into the player and begins to play.

CAUTION

Do not force the cassette tape into the tape door. This could damage the player.

When a cassette is inserted into the audio system, the word TAPE and a cassette side symbol (either one or two) illuminate in the display window. A cassette tape can be loaded with the ignition ON whether or not the radio power is on. Inserting a cassette tape with the radio power off causes the audio system to turn on. After the cassette is ejected, the audio system turns off. Also, the power antenna (if so equipped) stays in the down position during cassette tape operation. The cassette tape automatically changes directions to play the other side when the first side is completed. c To maintain good quality sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length.

c Cassette tapes should be removed from the player when not in use. Store

Z X

cassettes in their protective cases and away from direct sunlight, heat, moisture, and magnetic sources.

c Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.

c Do not use cassettes with peeling or loose labels, as the label could jam in the player.

c If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jamming and wavering sound quality.

c Over a period of time, a tape coating residue may accumulate on the play- back head, capstan, and pinch roller as the tape passes over the head. This residue accumulation can cause weak or wavering sound, and should be removed periodically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be dis- assembled for cleaning.

Use a Nissan Cassette Deck Cleaning Sys- tem or equivalent to clean the tape player head after 10-12 hours of play to help maintain the best playback sound and proper tape operation. REW and FF Push the REW (rewind) or FF (fast forward) button for the desired direction. When using REW, push the FF button momentarily to stop the tape and resume playing. Similarly, when using FF, push the REW button mo- mentarily to stop the tape and resume play- ing. Automatic Music Search (AMS) Pushing the SEEK button while playing a cassette tape activates the Automatic Music SEEK to Search (AMS) mode. Press rewind the tape to the previous selection, or press SEEK to forward the tape to the next selection. This system searches for the blank intervals between selections. If there is a blank inter- val within one program or there is no interval between programs, the system may not stop in the desired or expected location.

Changing the direction of tape play Press the SIDE 1-2 button to reverse the tape to the opposite track. The display win- dow indicates the track being played with a 1 or 2. Stopping and ejecting the cassette tape Push the EJ button. The cassette tape automatically ejects from the player and the radio turns off. A tape may be ejected with the ignition switch in the ON or OFF posi- tion. Dolby NR (noise reduction) Push the button for Dolby NR en- coded tapes to reduce high frequency tape noise. When activated, a appears in the display window. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. ‘‘Dolby NR’’ and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation.

Heater, air conditioner and audio systems 4-19

Z X

c Dirt and other foreign matter on the power antenna rod may interrupt its operation. Clean the rod periodically with a damp cloth. This type of cleaning is especially important dur- ing the winter seasons in areas where road salt and other chemicals may be spread on the road surfaces and splashed onto the antenna rod.

ANTENNA

Manual antenna The manual antenna on your vehicle re- mains in the up position at all times. The antenna cannot be shortened, but can be removed. When you need to remove the antenna, turn its base counterclockwise. Power antenna (if so equipped) The power antenna automatically extends when the radio is turned on, and retracts when turned off or when a tape or CD is played. If the radio is left on, the antenna retracts and extends with the ignition key OFF-ON operation.

CAUTION

c Before turning the radio on, make sure that there is no one near the antenna outlet and there is enough space for it to extend.

c To prevent damage, be sure that the power antenna is fully retracted be- fore the vehicle enters an automated car wash.

4-20 Heater, air conditioner and audio systems

Z X

CD magazine insert Once the desired number of CDs are loaded into the magazine, insert the magazine back into the CD changer. With the ignition switch OFF, the CD maga- zine loads into the CD changer. Once the ignition switch is turned to ACC or ON, the audio system returns to its previous mode. With the ignition switch in the ACC or ON position, the CD magazine loads into the CD changer and begins play with disc one, track one. CD Push this button to switch from radio or tape mode to CD mode. CD play begins auto- matically if at least one disc is loaded in the magazine. The display window shows the CD number for three seconds, then the track number for three seconds, then displays both together for the remainder of the track. Push this button when a CD is already playing to stop the CD. If the CD button is pushed while in the radio or tape mode, and there are no CDs loaded in the magazine, the display window flashes a NO DISC message for 4 seconds.

COMPACT DISC (CD) PLAYER (if so equipped) NOTE: Audio control features include com- mand buttons for CD players which can be installed as optional equipment to upgrade the audio system. A CD player is not in- cluded with this system, but can be pur- chased as an option at any time. Consult with an authorized NISSAN dealer for fea- ture availability. The compact disc player consists of two main components; the 6 CD magazine and the CD changer. Both components are lo-

AHA0597

cated on the center instrument panel con- sole, below the ashtray. How to load the CD magazine To load the magazine with CDs, first push the button on the CD changer to eject the magazine, then remove the magazine from the changer. The inside of the CD magazine contains six shelves, one for each CD to be loaded. Carefully slide a CD (label side up) onto one of the shelves and push it in. Repeat as desired, loading up to six CDs.

Heater, air conditioner and audio systems 4-21

Z X

SEEK SEEK to select the previous Push track number, or push SEEK to se- lect the next track number. After the last track on a disc, pushing SEEK se- lects the first track of the same disc. TUNE DISCS Push TUNE DISCS to select the pre- vious CD in the magazine. Push TUNE DISCS to select the next CD in the magazine. SCAN Push this button to audition the first 10
seconds of each track on a disc. At the end of the disc, the SCAN function continues with the first track on the same disc. The display window flashes the track number being auditioned during the SCAN function. REW Press this button to reverse the CD mecha- nism and move back to a previous point on the disc. If held for less than three seconds, this button causes the CD to reverse at three times the normal play speed. If held for more than three seconds, the CD re- 4-22 Heater, air conditioner and audio systems

verses at 10 times the normal play speed. The mechanism reverses to the beginning of track 1 and begins play if the button is held continuously. The volume decreases and the display window shows the elapsed time during the entire fast reverse period. FF Press this button to advance the CD mecha- nism and move ahead on the disc. If held for less than three seconds, this button causes the CD to advance at three times the normal play speed. If held for more than three seconds, the CD advances at 10 times the normal play speed. The volume decreases and the display win- dow shows the elapsed time during the entire fast forward period. COMP Press this button to activate the compres- sion function. This function reduces the dynamic range of the CD program material, which provides the listener with a more consistent level of volume. The display win- dow shows a C when the compression function is activated.

SHUFFLE Press this button to randomly select the play order of the tracks on a CD. When all tracks of one CD have been played, the system changes to the next CD in the magazine and proceeds to play the tracks in a ran- domly selected order. The shuffle feature remains in effect until turned off by pressing the SHUFFLE button again. When the shuffle function is activated, the display window shows the letters SHF for two seconds, then shows the disc number and track selected for the remainder of that selec- tion. When a new track is selected, the letters SHF reappear for two seconds, followed by the new disc and track number, and so on, as long as the shuffle function is active.

Z X

AHA0803

STEERING WHEEL CONTROLS The radio controls mounted on the right side of the steering wheel provide convenient access to three commonly used functions: VOL, and NEXT. Use the NEXT button to select the next pre- programmed station (AM/FM), the next se- lection on the tape, or the next selection on the CD.

VOL,

Heater, air conditioner and audio systems 4-23

Z X

REAR AUDIO CONTROLS Radio features controlled by the rear seat remote control (if so equipped) are listed below: c Volume: −/+ c Program advance: proceed to the next preset station (AM/FM), the other side of the tape, or the next CD.

c Source select: AM/FM, tape, or CD c Speakers ON/OFF c Seek: b c

AHA0595

Push the Memory three and Memory five buttons on the front radio controls simulta- neously to turn the rear controls on. Push them again to turn the rear audio controls off. The (headphones symbol) illuminates in the front display when the rear audio controls are on. Two headphone jacks are provided so two rear seat passengers may listen to the audio system privately. The rear volume controls can only increase the volume to the level at which the front radio volume control is set. Headphones are not included with the ve-

4-24 Heater, air conditioner and audio systems

hicle. Most portable radio headphones work with the rear audio controls. When the rear seat controls are on, push the SPKRS ON-OFF button to turn all speakers off. Push again to turn all speak- ers on. If the rear audio system was on when the ignition was turned OFF, the audio system ‘‘remembers’’ and the rear system is still on when the engine is started again. The sys- tem also ‘‘remembers’’ if the speakers were ON or OFF. Therefore, the speakers may have to be turned on again by pressing the SPKRS ON-OFF button or turning the rear audio controls off.

Z X

c Connect the ground wire from the

CB radio chassis to the body.

c For details, consult an authorized

NISSAN dealer.

CB RADIO OR CAR PHONE

from the driving

Microphone installed model If equipped with a genuine NISSAN cellular phone, your NISSAN features a non- directional microphone in the steering col- umn cover, so it is not necessary to look at or speak directly into the microphone when calling. To do so could detract operation and cause an accident. See the manual for car phone operation. Pre-wired and antenna for phone installed model Some models are pre-wired to accept the genuine NISSAN cellular phone. In addition, the same model has the phone antenna built into the rear glass window. When installing a CB ham radio, a car phone or other transmitters in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may ad- versely affect the MFI system and other electronic parts.

AHA1049

CAUTION

c Keep the antenna as far away as possible from the electronic control unit (including the radio).

c Also keep the antenna wire more than 8 inches (20 cm) away from the Multiport Electronic Fuel Injection (MFI) harness. Do not route the an- tenna wire next to any harness.

c Adjust the antenna standing-wave ratio as recommended by the manu- facturer.

Heater, air conditioner and audio systems 4-25

Z X

MEMO

4-26 Heater, air conditioner and audio systems

Z X

5 Starting and driving

Precautions when starting and driving...................5-2
Exhaust gas (carbon monoxide) ............................5-2
Three way catalyst .................................................5-2
Avoiding collision and rollover................................5-3
Drinking alcohol/drugs and driving.........................5-3
Ignition switch.........................................................5-4
Before starting the engine......................................5-5
Driving with an automatic transmission .................5-5
Overdrive switch.....................................................5-7
Starting the engine.................................................5-8

Parking brake operation.........................................5-9
Cruise control (if so equipped)...............................5-9
Break-in schedule ................................................5-11
Increasing fuel economy ......................................5-12
Parking/parking on hills........................................5-13
Power steering system.........................................5-14
Brake system........................................................5-14
Anti-lock brake system (ABS) (if so equipped)....5-15
Cold weather driving ............................................5-16

Z X

PRECAUTIONS WHEN STARTING AND DRIVING

WARNING

Do not leave children, unreliable adults, or pets alone in your vehicle. They could accidently injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

EXHAUST GAS (Carbon Monoxide)

WARNING

Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon monoxide is dan- gerous. It can cause unconsciousness or death. c If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.

c Do not run the engine in closed spaces such as a garage for any longer than is absolutely necessary.

5-2 Starting and driving

c Do not park the vehicle with the en- gine running for any extended length of time.

c Keep the rear door and flip-up rear window closed while driving, other- wise exhaust gases could be drawn into the passenger compartment. If you must drive in this manner for some reason, take the following steps. 1. Open all the windows. 2. Set the air recirculate switch to off and the fan control dial at four (high) to circulate the air.

c If electrical wiring or other cable connections must pass to a trailer through a seal on the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.

c The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service.

b. You suspect that exhaust fumes are entering into the passenger compartment.

c. You notice a change in the sound

of the exhaust system.

d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.

THREE WAY CATALYST The three way catalyst is an emission con- trol device installed in the exhaust system. Exhaust gases in the three way catalyst are burned at high temperatures to help reduce pollutants.

WARNING

c The exhaust gas and the exhaust system are very hot. Keep people or flammable materials away from the exhaust pipe.

c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

Z X

CAUTION

c Do not use leaded gasoline. Depos- its from leaded gasoline will seri- ously reduce the three way cata- lyst’s ability to help reduce exhaust pollutants.

c Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the catalyst, caus- ing it to overheat. Do not keep driv- ing if if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle in- spected promptly by an authorized NISSAN dealer.

the engine misfires, or

c Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three way catalyst.

c Do not race the engine while warm-

ing it up.

c Do not push or tow your vehicle to

start the engine.

AVOIDING COLLISION AND ROLLOVER

WARNING

Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.

Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects, or cause the vehicle to roll over, particularly if the vehicle slides sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the- counter drugs which may cause drowsi- ness). Always wear your seat belt as out- lined in the ‘‘Seat belts’’ section of this manual, and also instruct your passengers to do so.

DRINKING ALCOHOL/DRUGS AND DRIVING

WARNING

Never drive under the influence of alco- hol or drugs. Alcohol in the blood- stream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident alcohol can increase the se- verity of the injury.

NISSAN is committed to safe driving. How- ever, you must choose not to drive under the influence of alcohol. Every year thou- sands of people are injured or killed in alcohol related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is alcohol affects all people differently and most people un- derestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that’s true for drugs, too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.

Starting and driving 5-3

Z X

ACC (Accessories) This position activates electrical accesso- ries such as the radio when the engine is not running. ON (Normal operating position) This position turns on the ignition system and the electrical accessories. START This position activates the starter motor, which starts the engine.

IGNITION SWITCH

ASD0560

The ignition switch includes an anti-theft steering lock device. The key can only be removed when the ignition switch in the LOCK position. The ignition lock is designed so the key cannot be turned to LOCK and removed until the shift lever is moved to the P (Park) position. The shift lever is designed so it cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to LOCK, or if the key is removed from the switch. 5-4 Starting and driving

The shift lever can be moved out of P (Park) only after the ignition switch is in the ON position, and the foot brake pedal is depressed. To lock the steering wheel, remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.

WARNING

Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.

Key positions LOCK (Normal parking position) OFF The engine can be turned off without locking the steering wheel, if the key is left in the ignition.

Z X

BEFORE STARTING THE ENGINE

DRIVING WITH AN AUTOMATIC TRANSMISSION

c Make sure the area around the vehicle is

clear.

c Maintenance items listed here should be checked periodically (for example, each time you check engine oil).

c Check that all windows and lights are

clean.

c Visually inspect tires for their appearance and condition. Also check tires for proper inflation.

c Lock all doors. c Position seat and adjust head restraints. c Adjust inside and outside mirrors. c Fasten seat belts and ask all passengers

to do likewise.

c Check the operation of warning lights

when key is turned to the ON position.

WARNING

c Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to: R (Reverse), D (Drive), 2 or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.

c Cold engine idle speed is high, so use caution when shifting into a for- ward or reverse gear before the en- gine has warmed up.

c Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.

CAUTION

c When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brakes should be used for this purpose.

c On slippery roads, do not downshift.

This may cause a loss of control.

The automatic transmission in your vehicle is electronically controlled by a transmission control module to produce maximum power and smooth operation. Shown on the following pages are the rec- ommended operating procedures for this transmission. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle c After starting the engine, fully depress the foot brake pedal before shifting the selec- tor lever to the R (Reverse), N (Neutral), D (Drive), 2 or 1 position. Be sure the vehicle is at a complete stop before at- tempting to shift the selector lever.

This automatic transmission is designed so the foot brake pedal MUST be de- pressed before shifting from P (Park) to any other position while the ignition switch is ON. The shift lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to ACC, LOCK, or if the key is removed from the switch.

Starting and driving 5-5

Z X

If the battery charge is low, the shift lever can be moved if the ignition switch is in the ACC position. 1. Keep the foot brake pedal depressed and

shift into a driving gear.

2. Release the parking brake and foot brake, then gradually start the vehicle in motion.

5-6 Starting and driving

ASD0552

Shifting with automatic transmission P (Park): Use this selector position when the vehicle is parked or when starting the engine. Al- ways be sure the vehicle is at a complete stop. For maximum safety, depress the brake pedal, pull the lever toward you, and move the lever to the P (Park) position. Apply the parking brake. When parking on a hill, apply the parking brake first, then shift the lever into the P (Park) position.

Shifting from P (Park) If the ignition switch is in the ON position and the foot brake pedal is depressed, but the shift lever still cannot be moved out of P (Park), follow these instructions: 1. Shut the engine off and remove the key. 2. Apply the parking brake. 3. Reinsert the ignition key and turn it clock-

wise to the first position (ACC).

4. Depress the brake pedal, move the gear-

shift lever to N (Neutral).

5. Start the engine. R (Reverse): Use this position to back up. Always be sure the vehicle is completely stopped. Depress the brake pedal, then pull the shift lever toward you and move it to the R (Reverse) position.

Z X

forward

N (Neutral): Neither forward nor reverse gear is en- gaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal driving. 2 (Second gear): Use for hill climbing or engine braking on downhill grades. Do not downshift into 2 at speeds above 63
MPH (100 km/h). Do not exceed 63 MPH (100 km/h) in 2. 1 (Low gear): Use 1 when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. Do not exceed 38 MPH (60 km/h) in 1. Do not shift into 1 at speeds above 38 MPH (60 km/h).

Accelerator downshift In D position For rapid passing or hill climbing, fully depress the accelerator pedal to the floor. This shifts the transmission down into third gear, second gear or first gear, depending on the vehicle speed. Fail-safe When the Fail-safe operation occurs, the next time the key is turned to the ON position, the O/D OFF light blinks for ap- proximately 8 seconds after coming on for 2
seconds. While the vehicle can be driven under these circumstances, please note that the gears in the automatic transmission will be locked in 3rd gear. NOTE: If the vehicle is driven under extreme conditions, such as excessive wheel spinning and subsequent hard braking, the Fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition key OFF and wait for 3 seconds. Then turn the key back to the ON position. The vehicle should return to its normal operating condition. If it does not re- turn to its normal operating condition, have an authorized NISSAN dealer check the trans- mission and repair, if necessary.

OVERDRIVE SWITCH

ASD0561

Each time your vehicle is started, the trans- mission is automatically ‘‘reset’’ to overdrive ON. ON:

For normal driving the overdrive switch is engaged. The transmission is upshifted into overdrive as the vehicle speed increases.

The overdrive does not engage until the engine has reached operating tempera- ture. OFF: For driving up and down long slopes where engine ‘‘braking’’ is neces- sary, push the overdrive switch Starting and driving 5-7

Z X

STARTING THE ENGINE

1. Apply the parking brake. 2. Move the selector lever to P (Park) or N

(Neutral) (P is recommended). The shift selector lever cannot be moved out of P and into any of the other gear positions under the follow- ing conditions: c The ignition key is turned to the

OFF position.

c The ignition key is turned to the ON position without depressing the foot brake pedal.

The starter will not operate if the shift selector lever is in one of the driving positions.

3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. — If the engine is very hard to start in extremely cold or hot weather, de- press the accelerator pedal and hold it to help start the engine.

once. The O/D OFF indicator light illuminates at this time. When cruis- ing at a low speed or climbing a gentle slope, you may feel uncom- fortable shift shocks as the transmis- sion shifts between 3rd gear and overdrive repeatedly. In this case, press the overdrive switch.

When driving conditions change, press the overdrive switch to turn the overdrive on. The O/D OFF indicator light goes out. Remember not to drive at high speeds for extended periods of time with the O/D OFF light illuminated. This reduces the fuel economy.

5-8 Starting and driving

— In the summer, when restarting the engine within 30 minutes after it has been stopped, keep the accelerator pedal slightly depressed while start- ing.

CAUTION

Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, other- wise the starter could be damaged.

4. Warm-up

Allow the engine to idle for at least 30
seconds after starting. Drive at moderate speeds for a short distance first, espe- cially in cold weather.

Z X

PARKING BRAKE OPERATION

WARNING

c Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.

c Do not release the parking brake

from outside the vehicle.

c Do not use the gearshift in place of the parking brake. When parking, be sure the parking brake is fully en- gaged.

c Do not leave children unattended in a vehicle. They could release the parking brake and cause an acci- dent.

ASD0012

To apply: Firmly depress the parking brake. To release: 1. Firmly apply the foot brake. 2. Move the shift selector lever to the P

(Park) position.

3. Pull the parking brake release lever. 4. Before driving, be sure the brake warning

light goes out.

CRUISE CONTROL (if so equipped)

WARNING

Do not use the cruise control when driving under the following conditions: c it is not possible to keep the vehicle

at a set speed.

c in heavy traffic or in traffic that var-

ies in speed.

c on winding or hilly roads. c on slippery roads (rain, snow, ice,

etc.).

c in very windy areas. Doing so could cause a loss of vehicle control and result in an accident.

Starting and driving 5-9

Z X

The cruise control allows driving at speeds between 30 and 90 MPH (48 and 144 km/h) without keeping your foot on the accelerator pedal. To turn the cruise control on, push the CRUISE CONT main switch. The indicator light on the switch comes on. To set at cruising speed, accelerate your vehicle to the desired speed, push the COAST/SET switch and release it. The CRUISE light in the instrument cluster comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. 5-10 Starting and driving

c To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previ- ously set speed.

c The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control.

To cancel the preset speed, follow any of these three methods. a) Push the CANCEL button; the CRUISE

light in the instrument panel goes out.

ASD0562

b) Tap the brake pedal; the CRUISE light

goes out.

c) Push the cruise control OFF switch. Both the ON indicator and CRUISE lights go out. c If you depress the brake pedal while the

pushing the RES/ACCEL switch, RES/ ACCEL function is cancelled. In order for the RES/ACCEL switch to operate, the COAST/SET must be used to re-engage the system.

c The cruise control automatically cancels if the vehicle slows down more than 5
MPH (8 km/h) below the set speed.

Z X

c Move the selector lever to N (Neutral).

The CRUISE light goes out.

speed decreases by about 1 MPH (1.6
km/h).

To reset at a faster cruising speed, use one of the following three methods: a) Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.

b) Push and hold the RES/ACCEL switch. When the vehicle attains the speed you desire, release the switch.

c) Push and release the RES/ACCEL switch. Each time you do this, the set speed increases by about 1 MPH (1.6
km/h).

To reset at a slower cruising speed, use one of the following three methods. a) Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it.

b) Push and hold the COAST/SET switch. Release the switch when the vehicle slows down to the desired speed.

c) Push and release the COAST/SET switch. Each time you do this, the set

To resume the preset speed, push and release the RES/ACCEL switch. The ve- hicle resumes the last set cruising speed when the vehicle speed is over 30 MPH (48
km/h). Precautions c If the cruise control system malfunctions, it cancels automatically. The CRUISE light in the instrument panel then blinks to warn the driver.

c When the CRUISE light blinks, turn the CRUISE CONT main switch OFF and have the system checked by an autho- rized NISSAN dealer.

c The CRUISE light in the instrument panel may blink when the CRUISE CONT main switch is turned ON while pushing either the RES/ACCEL, COAST/SET, or the CANCEL switch (located on the steering wheel). To properly set the cruise control system, perform the steps in the order indicated.

BREAK-IN SCHEDULE

During the first 1,000 miles (1,600 km), follow these recommendations for the future reliability and fuel economy of your new vehicle. Failure to follow these recommen- dations may result in vehicle damage or shortened engine life. c Do not drive over 55 MPH (90 km/h) and do not run the engine over 4,000 RPM. Avoid driving for long periods at constant speed, either fast or slow.

c Do not accelerate at full throttle in any

gear.

c Avoid quick starts. c Avoid hard braking as much as possible. c Do not tow a trailer for the first 500 miles

(800 km).

Starting and driving 5-11

Z X

c Keep your engine tuned up. c Follow the recommended periodic main-

tenance schedule.

c Keep the tires inflated at

the correct pressure. Low tire pressure increases tire wear and wastes fuel.

c Keep the wheels in correct alignment. Improper alignment causes not only tire wear but also lower fuel economy.

c Air conditioner operation lowers fuel economy. Use the air conditioner only when necessary.

c When cruising at highway speeds, it is more economical to use the air condi- tioner and leave the windows closed to reduce drag.

INCREASING FUEL ECONOMY

SD1001M

c Accelerate slowly and smoothly. Main- tain cruising speeds with a constant ac- celerator position.

c Drive at moderate speeds on the high- way. Driving at high speed lowers fuel economy.

c Avoid unnecessary stopping and brak- ing. Maintain a safe distance behind other vehicles.

c Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.

c Avoid unnecessary engine idling. 5-12 Starting and driving

Z X

PARKING/PARKING ON HILLS

WARNING

WARNING

ASD0007

Do not park the vehicle over flammable materials such as dry grass, waste pa- per or rags. They may ignite and cause a fire.

1. Firmly apply the parking brake. 2. Move the gearshift lever to the P (Park)

position.

Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) position. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident. Make sure the shift lever has been pushed up as far as it can go and cannot be moved without pulling it towards you.

3. To help prevent the vehicle from rolling into the street when parked on a sloping driveway, it is a good practice to turn the wheels as illustrated.

c HEADED DOWNHILL WITH CURB: s1
Turn the wheels toward the curb and move the vehicle forward until the curb