1999 Nissan Pathfinder Owners Manual

inserting it into the key hole. ANTI-FREEZE In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check anti-freeze (ethylene glycol base) to assure proper winter protection. For details, see “En- gine cooling system” in the “8. Do-it-yourself” section. BATTERY If the battery is not fully charged during ex- tremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For details, see “Battery” in the “8. Do-it-yourself” section. DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti-freeze, drain the cooling system by open- ing the drain valves located under the radiator and on the engine block. Refill before operat- ing the vehicle. See “Engine cooling system” in the “8. Do-it-yourself” section for Changing Engine Coolant.

TIRE EQUIPMENT 1. SUMMER tires are of a tread design to provide superior performance on dry pave- ment. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your vehicle on snowy or icy roads, NISSAN recommends the use of MUD & SNOW or ALL SEASON tires on all four wheels. Please consult your NISSAN dealer for the tire type, size, speed rating and availability information.

2. For additional traction on icy roads, studded tires may be used. However, some Prov- inces and States prohibit their use, so, before installing studded tires, check local, state and provincial laws.

Skid and traction capabilities of studded snow tires, on wet or dry surfaces, may be poorer than that of non-studded snow tires.

3. TIRE CHAINS may be used if desired. Make sure they are of proper size for the tires on your vehicle and are installed ac- cording to the chain manufacturer’s sug- gestions. Use of tire chains may be prohib- ited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are of

proper size for the tires on your vehicle and are installed according to the chain manu- facturer’s suggestions. Use only SAE Class S chains. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufac- turer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely af- fected. Do not use the chains on dry roads.

Tire chains must be installed only on the rear wheels and not on the front wheels.

Do not drive with tire chains on paved roads which are clear of snow. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. When driving on clear paved roads, be sure to change to 2WD.

4. For four wheel drive:

If you install snow tires, they must also be the same size, brand, construction and tread pattern on all four wheels.

Starting and driving 5-27

Z 01.1.22/R50-D/V5 X

around your vehicle.

ENGINE BLOCK HEATER (if so equipped) An engine block heater to assist extreme cold temperature starting is available through your NISSAN dealer.

Do not use your heater with an un- grounded electrical system or two- pronged (cheater) adapters. You can be injured by an electrical shock if you use an ungrounded connection.

ONLY use spare tires specified for each four wheel drive model.

SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter:

1. A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.

2. A sturdy, flat board to be placed under the

jack to give it firm support.

3. A shovel to dig the vehicle out of snow-

drifts.

4. Extra window washer fluid to refill the res-

ervoir tank.

DRIVING ON SNOW OR ICE

I Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have a lot less traction or grip under

5-28 Starting and driving

these conditions. Try to avoid driving on wet ice until the road is salted or sanded.

I Whatever the condition, drive with caution. Accelerate and slow down with care. If accelerating or down- shifting too fast, the drive wheels will lose even more traction.

I Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement. I Allow greater following distances on

slippery roads.

I Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while actually on the ice, and avoid any sudden steering maneuvers.

I Do not use cruise control on slippery

roads.

I Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from

Z 01.1.22/R50-D/V5 X

6 In case of emergency

Flat tire ...................................................................... 6-2
Changing a flat tire.................................................... 6-2
Jump starting............................................................. 6-8
Push starting ........................................................... 6-10

If your vehicle overheats......................................... 6-10
Towing your vehicle ................................................ 6-11
Towing recommended by Nissan............................ 6-11
Vehicle recovery (Freeing a stuck vehicle)............. 6-14

Z 01.1.22/R50-D/V5 X

5. Raise the hood to warn other traffic and to signal professional road assistance person- nel that you require assistance.

6. Have all passengers get out of the vehicle and stand in a safe place away from traffic and clear of the vehicle.

I Make sure that the parking brake is securely applied and the manual transmission is shifted into R (re- verse), on the automatic transmis- sion in P (Park).

I Never change tires when the vehicle is on a slope, ice or a slippery area. This is hazardous.

I Never change tires if oncoming traffic is close to your vehicle. Wait for pro- fessional road assistance.

FLAT TIRE

CHANGING A FLAT TIRE If you have a flat tire, follow the instructions below. Stopping the vehicle 1. Safely move the vehicle off the road away

from traffic.

2. Turn on the hazard warning flasher.

3. Park on a level surface and apply the parking brake. Shift the manual transmis- sion into reverse (automatic transmission in P).

The transfer control lever must

be in the 2H, 4H or 4L position.

Never place the transfer control lever in the N position. Otherwise, the vehicle could roll unexpectedly even if the manual transmission is in gear or the automatic transmission is in the P posi- tion. This could result in serious per- sonal injury or property damage.

4. Turn off the engine.

6-2 In case of emergency

MCE0001

Blocking wheels Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire.

Be sure to block the wheel as the vehicle may move and could cause personal injury.

Z 01.1.22/R50-D/V5 X

SCE0112

Getting the spare tire and tools Remove jacking tools and spare tire from storage area.

Removing the spare tire cover (if so equipped) The spare tire cover cannot be removed or attached unless the spare tire is detached from the spare tire carrier.

1. Attach the cover to the entire periphery of the inner half and the top part of the spare tire.

2. Secure the spare tire to the spare tire

carrier as shown in the illustration.

3. Fasten the zip fastener of the spare tire

cover.

SCE0150

In case of emergency 6-3

Z 01.1.22/R50-D/V5 X

I Make sure the rod tip fits in the fitting portion of the spare tire hanger and turn the rod.

I Be sure to center the spare tire sus- pending plate on the wheel and then lift the spare tire.

SCE0120

SCE0116B

I Do not insert the jack rod straight as is designed to be inserted ob-

it liquely.

6-4 In case of emergency

Z 01.1.22/R50-D/V5 X

Removing wheel cap

SCE0140A

Jacking up the vehicle and removing the damaged tire Carefully read the following instructions.

1. Put the adapter stored in the tool bag on the

jack when jacking up the front side. Do not use the jack adapter for the rear.

2. Place the jack directly under the jack-up

point. The jack should be used on level firm ground.

3. Loosen each wheel nut one or two turns by

SCE0113

turning counterclockwise with the wheel nut wrench.

Do not remove the wheel nuts until the tire is off the ground.

4. Carefully raise the vehicle until

the tire clears the ground. To lift the vehicle, se- curely hold the jack lever and rod with both hands as shown above. Remove the wheel nuts, and then remove the wheel. Do not remove the brake drum with the wheel.

In case of emergency 6-5

Z 01.1.22/R50-D/V5 X

I Never get under the vehicle while it is

supported only by the jack.

I Use only the jack provided with your vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed only for lifting your vehicle during a tire change.

I Use the correct jack up points; never use any other part of the vehicle for jack support.

I Never jack up the vehicle more than

necessary.

I Never use blocks on or under the

jack.

I Do not start or run engine while ve- hicle is on the jack, as it may cause the vehicle to move. This is especially true for vehicle with limited slip dif- ferential carriers.

I Do not allow passengers to stay in

the vehicle while it is on the jack.

6-6 In case of emergency

I Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.

I Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.

As soon as possible tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

87 to 108 ft-lb (118 to 147 N(cid:215) m)

Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire placard affixed to the glove box lid. Retighten the wheel nuts when the vehicle has been run for 600 miles (1,000 km) after installing the aluminum wheel.

SCE0122

Installing the spare tire 1. Clean any mud or dirt

from the surface

between the wheel and hub.

2. Carefully put the wheel on and tighten the

wheel nuts finger tight.

3. With the wheel nut wrench, tighten wheel nuts alternately and evenly until they are tight.

4. Lower

the vehicle slowly until

the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence as illustrated.

Z 01.1.22/R50-D/V5 X

5. Securely store the spare tire and jacking

equipment in the vehicle.

Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dan- gerous projectiles in an accident or sud- den stop.

SCE0112

SCE0244

Stowing the damaged tire and tools Securely store the tire and jacking equipment in the vehicle as illustrated.

Tightening torque of nuts:

48 to 66 ft-lb (66 to 89 N(cid:215) m) Use a suitable padlock.

In case of emergency 6-7

Z 01.1.22/R50-D/V5 X

I Whenever working on or near a bat- tery, always wear suitable eye protec- tors (for example, goggles or indus- trial safety spectacles) and remove rings, metal bands, or any other metal jewelry. Do not lean over battery when jump-starting.

I Do not attempt to jump start a frozen battery. It could explode and cause serious injury.

I Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it.

JUMP STARTING

If you try to start your engine with a booster battery, follow the instructions and precautions below:

I If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.

I Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from it.

I Do not allow battery fluid to come into contact with eyes, skin, cloth or painted surfaces. Battery fluid is a corrosive sulphuric acid solution which can cause severe burns. If the fluid should come into contact with anything, immediately flush the con- tacted area with water.

I Keep battery out of the reach of chil-

dren.

I The booster battery must be rated at 12 volts. Use of an improperly rated battery can damage your vehicle.

Z 01.1.22/R50-D/V5 X

SCE0245

Do not insert the jack rod straight as it is designed to be inserted obliquely.

6-8 In case of emergency

Do not keep starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.

7. After starting your engine, carefully discon- nect the negative cable and then the posi- tive cable.

8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.

sion models, move the selector lever to P (Park)). Switch off all unnecessary electri- cal systems (light, heater, air conditioner, etc.).

3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.

4. Connect jumper cables in the sequence as

illustrated.

I Always connect positive (+) to posi- to body (for example, engine lift

tive (+) and negative (−) ground, bracket, etc. — not to the battery).

I Make sure that cables do not touch any moving parts in the engine com- partment and that clamps do not con- tact any other metal.

5. Start the engine of the other vehicle and let

it run for a few minutes.

6. Keep the engine speed of the other vehicle at about 2,000 rpm, and start your engine in the normal manner.

In case of emergency 6-9

Z 01.1.22/R50-D/V5 X

SCE0149

Always follow the instructions below exactly. Failure to do so could result in damage to the charging system and cause personal injury.

1. Position the two vehicles to bring their batteries into close proximity to each other if the booster battery is in another vehicle. Do not allow the two vehicles to touch. 2. Apply parking brakes. Move the shift lever to Neutral position (On automatic transmis-

PUSH STARTING

IF YOUR VEHICLE OVERHEATS

I Automatic transmission models can- not be push started. This may cause transmission damage.

I Three way catalyst equipped models should not be started by pushing since the three way catalyst may be damaged.

I Never try to start the vehicle by tow- ing it; when the engine starts, the forward surge could cause the ve- hicle to collide with the tow vehicle.

6-10 In case of emergency

If your vehicle is overheating indicated by an extremely high temperature gauge reading, or if you feel a lack of engine power, detect abnormal noise, etc., take the following steps:

I Do not continue to drive if your ve- hicle overheats. Doing so could cause a vehicle fire.

I To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radia- tor cap is removed, pressurized hot water will spurt out, possibly causing serious injury.

I Do not open the hood if steam is

coming out.

1. Move the vehicle safely off the road, apply the parking brake and move the gearshift lever to the neutral position (automatic transmission to P (Park)). Do not stop the engine.

2. Turn off the air conditioner switch. Open all the windows, move the heater or air condi- tioner temperature control to maximum hot

and fan control to high speed.

3. If engine overheating is caused by climbing a long hill on a hot day, run the engine at a fast idle (approximately 1,500 rpm) until the temperature gauge indication returns to normal.

4. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. Wait until no steam or coolant can be seen before pro- ceeding.

5. Open the engine hood.

If steam or water is coming from the engine, stand clear to prevent getting burned.

6. Visually check drive belts for damage or looseness. Also check if the cooling fan is running. The radiator hoses and radiator should not leak water. If coolant is leaking, the cooling fan belt is missing or loose or the cooling fan does not run, stop the engine.

Z 01.1.22/R50-D/V5 X

Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or to get caught in, the cooling fan, or drive belt.

7. After the engine cools down, check the coolant level in the reservoir tank with the engine running. Add coolant to the reservoir tank if necessary. Have your vehicle re- paired at the nearest NISSAN dealer.

TOWING YOUR VEHICLE

When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instruc- tions are available from your NISSAN dealer. Local service operators will generally be famil- iar with the applicable laws and procedures for towing. To assure proper towing and to pre- vent accidental damage to your vehicle, NISSAN recommends that you have a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions. TOWING RECOMMENDED BY NISSAN

I Never ride in a vehicle that is being

towed.

I Never get under your vehicle after it

has been lifted by a tow truck.

SCE0196

I When towing, make sure that

the transmission, axles, steering system and power train are in working condi- tion. If any unit is damaged, dollies must be used.

I Always attach safety chains before

towing.

I Never tow an automatic transmission model from the rear (that is back- ward) with four wheels on the ground

In case of emergency 6-11

Z 01.1.22/R50-D/V5 X

as this may cause serious and expen- sive damage to the transmission.

SCE0197

Two wheel drive models NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground as illustrated.

I When towing manual or automatic transmission models with the front wheels on the ground: Turn the igni- tion key to the OFF position and se- cure the steering wheel in a straigh- tahead position with a rope or similar device. Never place the ignition key in the LOCK position. This will result in damage to the steering lock mecha- nism.

I When towing manual

transmission models with the rear wheels on the ground or four wheels on the ground (if you do not use towing dollies): Always release the parking brake and move the transmission shift lever to the N (neutral) position. Observe the following restricted tow- ing speeds and distances. Manual transmission models: I Speed: Below 60 MPH (95 km/h) I Distance: Less than 500 miles (800

km)

6-12 In case of emergency

Z 01.1.22/R50-D/V5 X

If the speed or distance must necessarily be greater, remove the propeller shaft beforehand to prevent damage to the transmission.

If towing with the front wheels on the ground or with the rear wheels on the ground (if you cannot use towing dol- lies) is necessary: Move the transfer case shift lever into the 2H position. I When towing with the front wheels on the ground: On manual transmission models to move the shift lever to the N (neutral) position, turn the ignition key to the OFF position and secure the steering wheel in a straightahead position with a rope on similar de- vice.

On automatic transmission models to move the selector lever to N (neutral) position, turn the ignition key to the ACC position. After moving the selec- tor lever to the N (neutral) position, turn the ignition key to the OFF posi- tion and secure the steering wheel in a straightahead position with a rope or similar device.

Never place the ignition key in the LOCK position. This will result in

In case of emergency 6-13

SCE0198

Four wheel drive models NISSAN recommends that a dolly be used as illustrated when towing four wheel drive mod- els.

Z 01.1.22/R50-D/V5 X

damage to the steering lock mecha- nism.

I When towing manual

transmission models with the rear wheels on the ground or four wheels on the ground: Always release the parking brake and move the transmission shift lever to the N (neutral) position.

Observe the following restricted tow- ing speeds and distances.

Manual transmission models: I Speed: Below 60 MPH (95 km/h) I Distance: Less than 500 miles (800

km)

If the speed or distance must necessarily be greater, remove the front and rear propeller shafts beforehand to prevent damage to the transmission.

6-14 In case of emergency

SCE0115A

VEHICLE RECOVERY (Freeing a stuck vehicle) I Use the towing hook only, not other parts of the vehicle. Otherwise, the vehicle body will be damaged.

I Use the towing hook only to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle for a long distance using only the towing hook.

SCE0138
I The towing hook is under tremendous force when used to free a stuck vehicle. Always pull the cable straight out from the front of the vehicle. Never pull on the hook at an angle.

I Stand clear of a stuck vehicle.

Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be

Z 01.1.22/R50-D/V5 X

damaged.

In case of emergency 6-15

Z 01.1.22/R50-D/V5 X

MEMO

6-16 In case of emergency

Z 01.1.22/R50-D/V5 X

7 Appearance and care

Cleaning exterior ....................................................... 7-2
Washing .................................................................... 7-2
Waxing ...................................................................... 7-2
Removing spots ........................................................ 7-3
Underbody................................................................. 7-3
Glass ......................................................................... 7-3
Aluminum alloy wheels.............................................. 7-3
Chrome parts ............................................................ 7-3

Cleaning interior ........................................................ 7-3
Floor mats ................................................................. 7-4
Seat belts .................................................................. 7-4
Corrosion protection.................................................. 7-4
Most common factors contributing to vehicle corrosion.................................................................... 7-4
To protect your vehicle from corrosion ..................... 7-5

Z 01.1.22/R50-D/V5 X

CLEANING EXTERIOR

MAI0001

In order to maintain the appearance of your vehicle, it is important to take proper care of it.

In the following cases, please wash your ve- hicle as soon as possible to protect the paint surface. I After a rainfall to prevent possible damage

from acid rain

I After driving on coastal roads I When contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface

I When dust or mud builds up on the surface 7-2 Appearance and care

Whenever possible, store or park your vehicle inside a garage or in a covered area.

When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap such as Nissan Car Wash, or a general purpose dish-washing liquid mixed with clean, lukewarm (never hot) water.

I Do not use strong household soap, strong chemical detergents, gasoline or solvents.

I Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted.

I Avoid using tight-napped or rough cloths, such as washing mitts. Care

must be taken when removing caked-on dirt or other foreign sub- stance so that the paint surface is not scratched or damaged.

Rinse the vehicle thoroughly with plenty of clean water.

Inside flanges, seams and folds on the doors, hatches and hood are particularly endangered by the effects of road salt. Therefore, these areas must be regularly cleaned. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots. WAXING Regular waxing protects the paintwork and keeps the finish. After waxing, polishing is recommended to remove built-up residue and avoid a “weathered” appearance. Your NISSAN dealer can assist you in choos- ing the proper product. I Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax.

Z 01.1.22/R50-D/V5 X

I Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.

I If the surface does not polish easily, use a

road tar remover and wax again.

Machine compounding or aggressive pol- ishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks.

Only apply black wax or black shoe polish to the black urethane or polypropylene bumper. REMOVING SPOTS Remove tar and oil spots, industrial dust, in- sects and tree sap as quickly as possible from the surface of the paint to avoid lasting dam- age or staining. Special cleaning products are available at your NISSAN dealer or any auto- motive accessories store. UNDERBODY In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing corrosion on the underbody and suspension. Before the winter period and again in the spring, the underseal must be checked and, if necessary, re-treated.

GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to be coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.

I When cleaning the inside of the win- dow, do not use any sharp-edged tools or chlorine-based disinfectant cleaners. I These may damage the radio antenna

abrasive

cleaners

or

elements or rear window defroster.

ALUMINUM ALLOY WHEELS Wash regularly, especially during winter months in areas where road salt is used. Salt could discolor the wheel if not removed. CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish.

CLEANING INTERIOR

Occasionally remove loose dust from the inte- rior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry soft cloth. Before using any fabric protector, read the manufacturer’s rec- ommendations. Some fabric protectors con- tains chemicals that stain or bleach the seat material.

I Never use benzine, thinner or any

similar material.

I The leather seats should be regularly coated with a leather wax like saddle soap. Never use car wax.

I Never use fabric protectors unless recommended by the manufacturer.

Appearance and care 7-3

Z 01.1.22/R50-D/V5 X

Floor mat positioning aid (Driver side only) This model includes a front floor mat bracket to act as a floor mat positioning aid. NISSAN floor mats have been specially designed for your vehicle model. The driver side floor mat has a grommet hole incorporated in it. Simply posi- tion the mat by placing the floor mat bracket through the floor mat grommet hole while centering the mat in the floorpan contour. Periodically check to make certain the mats are properly positioned. SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solu- tion. Allow the belts to dry completely before using them.

Do not allow wet belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents since these may se- verely weaken the seat belt webbing.

CORROSION PROTECTION

MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1. The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.

2. Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.

Moisture The accumulation of sand, dirt and water on the underside of the body will accelerate cor- rosion. Floor sections which have snow and ice trapped under the floor matting will not dry. Relative humidity Corrosion will be accelerated: I in areas of high relative humidity I especially in areas where the temperatures

stay above freezing

I where atmospheric pollution exists I where road salt is used

Z 01.1.22/R50-D/V5 X

SAI0009

FLOOR MATS The use of Genuine Nissan floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn.

7-4 Appearance and care

Temperature A temperature increase will accelerate the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use will accelerate the corrosion process. Road salt will also accelerate the disintegration of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION I Wash and wax your vehicle often to keep

the vehicle clean.

I Always check for minor damage to the paint

and repair it as soon as possible.

I Keep drain holes at the bottom of the doors and tailgate open to avoid water accumula- tion.

I Check the underbody. If any sand, dirt or salt is accumulated, wash it off with water as soon as possible.

I NEVER remove dirt, sand or other debris from the passenger compart- ment by washing with a hose. Re- move dirt with a vacuum cleaner or broom.

I Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle.

Chemicals used for road surface de-icing are extremely corrosive and will accelerate corro- sion and the deterioration of underbody com- ponents such as the exhaust system, fuel and brake lines, brake cables, floor pan and fend- ers. In winter, the underbody must be cleaned periodically.

For additional protection against rust and cor- rosion, which may be required in some areas, consult your local NISSAN dealer.

Appearance and care 7-5

Z 01.1.22/R50-D/V5 X

MEMO

7-6 Appearance and care

Z 01.1.22/R50-D/V5 X

8 Do-it-yourself

Maintenance precautions .......................................... 8-2
Engine compartment check locations ....................... 8-3
Engine cooling system .............................................. 8-4
Checking engine coolant level .................................. 8-4
Changing engine coolant .......................................... 8-5
Engine oil .................................................................. 8-7
Checking engine oil level .......................................... 8-7
Changing engine oil .................................................. 8-8
Changing engine oil filter .......................................... 8-9
Automatic transmission fluid ..................................... 8-9
Temperature conditions for checking...................... 8-10
Power steering fluid ................................................ 8-11
Brake and clutch fluid ............................................. 8-11
Brake fluid ............................................................... 8-11
Clutch fluid .............................................................. 8-12
Window washer fluid ............................................... 8-12
Window washer fluid reservoir ................................ 8-12
Battery ..................................................................... 8-13
Jump starting........................................................... 8-14
Drive belts ............................................................... 8-14
Spark plugs ............................................................. 8-15
Replacing spark plugs............................................. 8-15

Air cleaner ............................................................... 8-16
Windshield wiper blades ......................................... 8-17
Cleaning .................................................................. 8-17
Replacement ........................................................... 8-17
Parking brake and brake pedal............................... 8-18
Checking parking brake .......................................... 8-18
Checking brake pedal ............................................. 8-19
Brake booster.......................................................... 8-19
Clutch pedal ............................................................ 8-20
Checking clutch pedal............................................. 8-20
Fuses....................................................................... 8-20
Engine compartment ............................................... 8-20
Passenger compartment ......................................... 8-21
Lights....................................................................... 8-22
Headlights ............................................................... 8-23
Tires and wheels..................................................... 8-26
Tire pressure ........................................................... 8-26
Types of tires .......................................................... 8-27
Tire chains............................................................... 8-28
Changing tires and wheels...................................... 8-28
Clutch housing drain ................................... 8-31

Z 01.1.22/R50-D/V5 X

MAINTENANCE PRECAUTIONS

When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed.

I Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. For a manual transmission, move the shift lever to Neutral. For an automatic transmis- sion, move the selector lever to P (Park).

I Be sure the ignition key is in the OFF or LOCK position when performing any replacement or repair.

I If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans and fan belts.

I It is advisable to remove necktie and any jewelry, such as rings, watches, etc. before working on your vehicle.

8-2 Do-it-yourself

I Always wear eye protection when-

ever you work on your vehicle.

I If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases.

I Never get under the vehicle while it is supported only by a jack. If it is nec- essary to work under the vehicle, support it with safety stands.

I Keep smoking materials, flame and

sparks away from fuel and battery.

I The fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.

ponent connector while the ignition key is on.

I Avoid direct contact with used engine oil. Improperly disposed motor oil and/ or other vehicle fluids can hurt the environment. Always conform to lo- cal regulations for disposal of vehicle fluid.

This “8. Do-it-yourself” section gives instruc- tions regarding only those items which are relatively easy for an owner to perform. You should be aware that incomplete or im- proper servicing may result in operating diffi- culties or excessive emissions, and could af- fect your warranty coverage. If in doubt about any servicing, have it done by your NISSAN dealer.

I Do not work under the engine hood while it is hot. Always turn off the engine and wait until it cools down. I Never connect or disconnect either the battery or any transistorized com-

Z 01.1.22/R50-D/V5 X

ENGINE COMPARTMENT CHECK LOCATIONS VG33E engine

SDI0418A Do-it-yourself 8-3

Z 01.1.22/R50-D/V5 X

I Never remove the radiator cap when the engine is hot; serious burns could be caused by high pressure fluid escaping from the radiator. Wait until the engine and radiator cool down. Serious burns could be caused by high pressure fluid escaping from the radiator. See “If your vehicle over- heats” in the “6. In case of emer- gency” section.

I The radiator is equipped with a pres- sure cap. Use only a genuine cap as a replacement.

ENGINE COOLING SYSTEM

The engine cooling system is filled at the factory with a high-quality, year-round, anti- freeze coolant solution. The anti-freeze solu- tion contains rust and corrosion inhibitors, therefore additional cooling system additives are not necessary.

When adding or replacing the coolant, be sure to use Genuine Nissan Anti- Freeze Coolant or equivalent with the proper mixture ratio of 50% anti-freeze and 50% demineralized water/distilled water. The use of other types of coolant solutions may damage your engine cooling system.

Outside temperature down to

°C

−35

°F

−30

Anti- freeze

Deminer- alized water or distilled water

50%

50%

8-4 Do-it-yourself

SDI0378

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level. If the engine cooling system frequently

Z 01.1.22/R50-D/V5 X

requires coolant, have it checked by your NISSAN dealer.

SDI0485

SDI0486

CHANGING ENGINE COOLANT I Major cooling system repairs should be performed by your NISSAN dealer. The service procedures can be found in the appropriate NISSAN Service Manual.

I Improper servicing can result in reduced heater performance and engine overheat- ing.

I To avoid the danger of being scalded, never change the coolant when the engine is hot.

I Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

Do-it-yourself 8-5

Z 01.1.22/R50-D/V5 X

SDI0409

SDI0410

SDI0419

1. Perform the following procedure to open

the heater water cock. I Turn the ignition key from OFF to ON. I Move the heater or air conditioner tem- perature control dial to the maximum hot position then turn the ignition key to OFF.

2. Open the radiator drain plug and radiator

cap. Open the drain plugs on the engine block.

8-6 Do-it-yourself

3. Open the air release plug to drain the

coolant.

4. Flush the cooling system by running fresh

water through the radiator.

5. Close the radiator drain plug and engine

block drain plugs securely.

6. See the “Technical information” section for

cooling system capacity. Fill the radiator slowly with the proper mix- ture of coolant and water. Fill the reservoir tank slowly up to the MAX level. Then install the radiator cap and close the air release plug.

7. Start

the engine and warm it up until

it reaches normal operating temperature. Then race the engine 2 or 3 times under no load. Watch the coolant temperature gauge for signs of overheating.

8. Stop the engine. After it completely cools down, refill the radiator up to the filler opening. Fill the reservoir tank up the MAX level.

9. Check the radiator drain plug and engine block drain plugs for any sign of leakage.

Z 01.1.22/R50-D/V5 X

ENGINE OIL

Oil level should be checked regularly. Operating with insufficient amount of oil can damage the engine, and such dam- age is not covered by warranty.

SDI0420

SDI0487

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until

temperature.

it reaches operating

3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil pan.

4. Remove the dipstick and wipe it clean.

Reinsert it all the way.

5. Remove the dipstick again and check the oil level. It should be between the H and L marks. If the oil level is below the L mark, remove the oil filler cap and pour recom- mended oil through the opening. Do not overfill.

6. Recheck oil level with dipstick. It is normal to add some oil between oil changes or during the break-in period, de- pending on the severity of operating con- ditions.

Do-it-yourself 8-7

Z 01.1.22/R50-D/V5 X

section for changing engine oil filter.

Be careful not to burn yourself, as the engine oil is hot.

Waste oil must be disposed of properly. Check your local regulations.

6. Clean and re-install the drain plug and new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque:

22 to 29 ft-lb (29 to 39 N(cid:215) m)

7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely.

8. Start the engine.

Check for leakage around the drain plug. Correct as required.

9. Turn the engine off and wait several min- utes. Check the oil level with the dipstick. Add engine oil if necessary.

I Prolonged and repeated contact with used engine oil may cause skin can- cer.

I Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

I Keep used engine oil out of reach of

children.

and

“Capacities

See recommended fuel/lubricants” in the “10. Technical and consumer information” section for drain and refill capacity.

The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.

Z 01.1.22/R50-D/V5 X

SDI0416

CHANGING ENGINE OIL 1. Park the vehicle on a level surface and

apply the parking brake.

2. Warm up the engine until it reaches oper-

ating temperature, and then turn it off.

3. Place a large drain pan under the drain

plug.

4. Remove the oil filler cap. 5. Remove the drain plug with a wrench and

completely drain the oil. If the oil filter is to be changed, remove and replace it at this time. See later in this

8-8 Do-it-yourself

Be careful not to burn yourself, as the engine oil may be hot.

4. Wipe the engine oil filter mounting surface

with a clean rag. Be sure to remove any old rubber gasket remaining on the mounting surface of the engine.

5. Coat the rubber gasket on the new filter

with engine oil.

6. Screw in the oil filter until a slight resistance

is felt, then tighten an additional 2/3 turn.

7. Start

the engine and check for leakage

around the oil filter. Correct as required.

8. Turn the engine off and wait several min- utes. Check the oil level. Add engine oil if necessary.

SDI0417

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and

apply the parking brake.

2. Turn the engine off. 3. Loosen the oil filter with an oil filter wrench. (A special cap-type wrench will assist with oil filter removal on models with the V6
engine. This tool can be purchased from your NISSAN dealer.) Then remove the oil filter by turning it by hand.

AUTOMATIC TRANSMISSION FLUID

SDI0488

I When engine is running, keep hands, jewelry, and clothing away from any moving parts such as fan and drive belt.

I Automatic transmission fluid is poi- sonous and should be stored care- fully in marked containers out of the reach of children.

Do-it-yourself 8-9

Z 01.1.22/R50-D/V5 X

5. Re-insert the dipstick into the charging pipe

as far as it will go.

6. Remove the dipstick and note the reading. If the level is on the low side of either range, add fluid to the charging pipe.

(Canada).

DexronTM

Automatic

I Do not overfill. I USE ONLY Nissan Matic D (Continen- tal U.S. and Alaska) or Genuine Transmission Nissan Fluid III/ MerconTM or equivalent may also be used. Outside the continental United States and Alaska contact a NISSAN dealer for more information regarding suitable fluids, including recom- mended brand(s) of DexronTM III/ MerconTM or DexronTM IIE/MerconTM Automatic Transmission Fluid.

TEMPERATURE CONDITIONS FOR CHECKING The fluid level should be checked using the HOT range (L & H marks) on the dipstick at fluid temperatures between 122 and 176°F (50
and 80°C) after the vehicle has been driven approximately 5 minutes in urban areas after the engine is warmed up. The level can be checked at fluid temperatures between 86 and 122°F (30 and 50°C) using the COLD range on the dipstick for reference, after the engine is warmed up but before driving. However, the fluid level must be rechecked using the HOT range. 1. Park the vehicle on a level surface and set

the parking brake.

2. Start the engine and then move the selector lever through each gear range, ending in P. 3. Check the fluid level with the engine idling. If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the fluid level cannot be read accu- rately. You should wait until the fluid has cooled down (about 30 minutes).

4. Remove the dipstick and wipe it clean with

lint-free paper.

8-10 Do-it-yourself

Z 01.1.22/R50-D/V5 X

SDI0386A

POWER STEERING FLUID

BRAKE AND CLUTCH FLUID

and clutch systems. The use of im- proper fluids can damage the brake sys- tem and affect the vehicle’s stopping ability.

Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, wash with water.

DI0187M

SDI0847

Check the fluid level.

The fluid level should be checked using the HOT range on the dipstick at fluid tempera- tures of 122 to 176°F (50 to 80°C) or using the COLD range on the dipstick at fluid tempera- tures of 32 to 86°F (0 to 30°C).

I Do not overfill. I Recommended fluid is Genuine

Nissan PSF II or equivalent.

BRAKE FLUID Check the fluid level in the reservoir. If the fluid level line or the brake warning light comes on, add DOT 3 fluid up to the MAX. line.

is below the MIN.

If fluid is added frequently, the system should be thoroughly checked by your NISSAN dealer.

Use only new fluid. Old, inferior or con- taminated fluid may damage the brake

Do-it-yourself 8-11

Z 01.1.22/R50-D/V5 X

WINDOW WASHER FLUID

and clutch systems. The use of im- proper fluids can damage the brake sys- tem and affect the vehicle’s stopping ability.

Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, wash with water.

SDI0844

CLUTCH FLUID Check the fluid level in the reservoir. If the fluid level line or the brake warning light comes on, add DOT 3 fluid up to the MAX. line.

is below the MIN.

If fluid is added frequently, the system should be thoroughly checked by your NISSAN dealer.

Use only new fluid. Old, inferior or con- taminated fluid may damage the brake

8-12 Do-it-yourself

SDI0423A

WINDOW WASHER FLUID RESERVOIR For US To check the fluid level, use your finger to plug the center hole of the cap/tube assembly (as shown above), then remove it from the tank. If there is no fluid in the tube, add fluid. Add a washer solvent to the water for better cleaning. In the winter season, add a windshield washer anti-freeze. Follow the manufacturer’s instruc- tions for the mixture ratio.

Z 01.1.22/R50-D/V5 X

Anti-freeze is poisonous and should be stored carefully marked containers out of the reach of children.

BATTERY

I Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water.

I Make certain the terminal connections are

clean and securely tightened.

I If the vehicle is not to be used for 30 days or longer, disconnect the (—) negative battery terminal cable to prevent discharge.

I Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by battery action is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.

I When working on or near a battery, always wear suitable eye protection and remove all jewelry.

I Keep the battery out of the reach of Do-it-yourself 8-13

Z 01.1.22/R50-D/V5 X

SDI0389

For CANADA Add fluid when the low washer fluid warning light comes on. Add a washer solvent to the water for better cleaning. In the winter season, add a windshield washer anti-freeze. Follow the manufacturer’s instructions for the mixture ratio.

Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint.

DRIVE BELTS

children.

JUMP STARTING If jump starting is necessary, see “Jump start- ing” in the “6. In case of emergency” section. If the engine does not start by jump starting, the battery may have to be replaced. Contact your NISSAN dealer.

DI0137M

SDI0424

Check the fluid level in each cell. It should be between the MAX. and MIN. lines. If it is necessary to add fluid, add only distilled water to bring the level to the indicator in each filler opening. Do not overfill. 1. Remove the cell plugs using a suitable tool. 2. Add distilled water up to the MAX. level. 3. Tighten cell plugs.

Be sure the ignition key is OFF. The engine could rotate unexpectedly.

1. Visually inspect each belt for signs of un- usual wear, cuts, fraying or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by your NISSAN dealer.

2. Have the belts checked regularly for condi- tion and tension in accordance with the maintenance schedule in this manual.

Z 01.1.22/R50-D/V5 X

8-14 Do-it-yourself

SPARK PLUGS

engaged securely.

REPLACING SPARK PLUGS 1. Disconnect spark plug cables. Keep track

of the original cable location.

When disconnecting, always hold the boots — not the cables. Mark all cables to identify their original location.

SDI0723

Be sure the engine and ignition switch are off and that the parking brake is

2. Remove spark plugs with a spark plug

wrench. (Type A or B)

SDI0392

Be sure to use the correct wrench to remove the plugs. An incorrect wrench can cause damage.

Do-it-yourself 8-15

Z 01.1.22/R50-D/V5 X

AIR CLEANER

SDI0390

DI0065

SDI0393

3. Check each new spark plug gap with a

feeler gauge. Correct it as required.

4. Install spark plugs. When installing a plug, turn it in two or three turns by hand and then tighten with a spark plug wrench. Be careful not to over- tighten it.

The filter element should not be cleaned and reused as it is given a special treatment. We recommended it be replaced according to the maintenance intervals. See “Periodic mainte- nance” in the “9. Maintenance” section for maintenance intervals. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.

Tightening torque:

14 to 22 ft-lb (20 to 29 N(cid:215) m)

5. Reconnect the spark plug cables to their

original positions.

I Operating the engine with the air cleaner off can cause you or others to be burned. The air cleaner not only

8-16 Do-it-yourself

SDI0391

Z 01.1.22/R50-D/V5 X

WINDSHIELD WIPER BLADES

cleans the air, it stops flame if the engine backfires. If it is not there, and the engine backfires, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner off.

I Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

DI0155MA

the blades and using the wiper, replace the blades. REPLACEMENT 1. Pull the wiper arm. 2. Push the lock pin, then remove the wiper

blade.

3. Insert the new wiper blade to the wiper arm

until a click sounds.

CLEANING If your windshield is not clear after using the windshield washer of if a wiper blade chatters when running, wax or other material may be on the blade or windshield.

the windshield with a Clean the outside of washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water.

Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter- gent. Then rinse the blade with clear water. If your windshield is still not clear after cleaning

Do-it-yourself 8-17

Z 01.1.22/R50-D/V5 X

After wiper blade replacement, return the wiper arm to its original position.

Otherwise it may be damaged when the engine hood is opened.

Make sure the wiper blade contacts the glass. Otherwise, the arm may be dam- aged from wind pressure.

PARKING BRAKE AND BRAKE PEDAL

DI1010-C

CHECKING PARKING BRAKE Pull the parking brake lever up. If the number of clicks is out of the range as listed above, see your NISSAN dealer.

8-18 Do-it-yourself

SDI0425

If you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may cause clogging or im- proper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin.

Z 01.1.22/R50-D/V5 X

Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes.

The front disc-type brakes self-adjust every time the brake pedal is applied. The rear drum-type brakes self-adjust every time the parking brake is applied. If the brake pedal goes down farther than normal, it may be due to a lack of adjustment of the rear drum brakes. Apply the parking brake several times.

DI0453

CHECKING BRAKE PEDAL With the engine running, check distance A between the upper surface of the pedal and the dash lower panel. Distance A

M/T models

2-1/2 in (65 mm) or more

A/T models

2-3/4 in (70 mm) or more

If it is out of the range shown above, see your NISSAN dealer.

See your NISSAN dealer and have it checked if the brake pedal height does not return to normal.

Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires replacement, it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indi- cator sound is heard. Under some driving or climate conditions, oc-

casional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system.

The rear drum brakes (if so equipped) do not have audible wear indicators. Should you ever hear an unusually loud noise from the rear drum brakes, have them inspected as soon as possible by your NISSAN dealer. Proper brake inspection intervals should be followed. For additional information, see “Periodic maintenance” in the “9. Mainte- nance” section for maintenance intervals. BRAKE BOOSTER Check the brake booster function with the following steps: 1. With the engine off, press and release the times. When brake brake pedal several travel) re- pedal movement (distance of mains the same from one pedal application to the next, continue on to the next step.

2. While depressing the brake pedal, start the engine. The pedal height should drop a little.

3. With the brake pedal depressed, stop the engine. Keeping the pedal depressed for Do-it-yourself 8-19

Z 01.1.22/R50-D/V5 X

CLUTCH PEDAL

FUSES

about 30 seconds, the pedal height should not change.

4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradu- ally with each depression as the vacuum is released from the booster.

If the brakes do not operate properly, have the brake checked by your NISSAN dealer.

DI0070-B

SDI0395

CHECKING CLUTCH PEDAL Press the pedal by hand and be sure the free travel is within the above limit. If free travel is out of the range shown above, see your NISSAN dealer.

ENGINE COMPARTMENT

Never use a fuse of higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse.

1. Be sure the ignition key and the headlight

switch are OFF.

Z 01.1.22/R50-D/V5 X

8-20 Do-it-yourself

2. Open the engine hood. 3. Remove the fuse box cover. 4. Remove the fuse with the fuse puller. 5. If the fuse is open, replace it with a new

fuse.

6. If a new fuse opens again, have the elec- trical system checked and repaired by your NISSAN dealer.

Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts.

PASSENGER COMPARTMENT

Never use a fuse of higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse.

1. Be sure the ignition key and the headlight

switch are OFF.

SDI0447

2. Pull to open the fuse box cover/coin tray. 3. Pull the fuse box cover/coin tray horizon-

tally to remove it.

4. Remove the fuse with the fuse puller. 5. If the fuse is open, replace it with a new

fuse.

6. If a new fuse opens again, have the elec- trical system checked and repaired by your NISSAN dealer.

Do-it-yourself 8-21

Z 01.1.22/R50-D/V5 X

LIGHTS

8-22 Do-it-yourself

SDI0907

Z 01.1.22/R50-D/V5 X

HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. A bulb can be replaced inside the engine compartment without removing the headlight assembly.

6. Install the new bulb in the reverse order of

removal.

Aiming is not necessary after replacing the bulb. When aiming adjustment is neces- sary, contact your NISSAN dealer.

High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

Hold the plastic base when handling the bulb. Never touch the glass envelope.

Replacing the headlight bulb 1. Disconnect the battery negative cable.

2. Disconnect

the electrical connector from

the rear end of the bulb.

3. Pull off the rubber cap.

4. Push and turn the retaining pin to loosen it.

5. Remove the headlight bulb. Do not shake

or rotate the bulb when removing it.

SDI0908

DO NOT TOUCH THE BULB. I Be sure the lip of the rubber cap

contacts the headlight body.

I Use the same number and wattage as

originally installed:

Wattage 60/55
Bulb No. HB2

I Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the headlight.

Do-it-yourself 8-23

Z 01.1.22/R50-D/V5 X

Item

Wattage (W)

Side combination light

Front fog light (H3 type)

Rear combination light

Turn signal

Stop/Tail

Back-up

High mounted stop light

License plate light

Interior light

Vanity mirror light

Personal light

*1: For 5W light *2: Option Bulb identification

MDI0006

21/5

55

27

21/5

18

5 or 10

7.5

10

1.4

Bulb No.

7443

1156

7443

921

168

168*1
89*2

—

—

—

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.

8-24 Do-it-yourself

Z 01.1.22/R50-D/V5 X

SDI0910

SDI0911