1998 Nissan Pathfinder Owners Manual

Have the warning system checked by a NISSAN dealer.

I Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for re- pairs. Otherwise, have your vehicle towed.

I Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stopping dis- tance and braking will require greater pedal effort as well as greater pedal travel.

I If the brake fluid level is below the MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN

dealer.

or

Anti-lock brake warning light

If the light comes on while the engine is running, it may indicate there is something wrong with the anti-lock brake system. Have the system checked by your NISSAN dealer. If an abnormality occurs in the system, the anti-lock function will cease but the ordinary brakes will continue to operate normally. If the light comes on while you are driving, contact your NISSAN dealer for repair.

Automatic transmission park warning light (

model)

This light indicates that the automatic trans- mission parking function is not engaged. If the transfer control is not secured in any drive position while the automatic transmission se- lector lever is in the P position, the transmis- sion will disengage and the wheel will not lock. Shift the transfer control lever into the 2H or 4L position when the warning light comes on.

Instruments and controls 2-11

Z 01.1.31/R50-D X

Automatic transmission oil temperature warning light

model)

This light comes on when the automatic trans- mission oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off. Continued vehicle operation when the A/T oil temperature warning light is on may damage the automatic transmission.

Tire carrier open warning light (if so equipped)

This light comes on when the tire carrier is not closed securely while the ignition key is ON. INDICATOR LIGHTS

Overdrive off indicator light

This light comes on during driving when the overdrive switch is pressed to prevent over- drive operation. The O/D OFF indicator light comes on for two seconds each time the ignition key is turned ON. This shows the light is functioning prop- erly. If 2-12 Instruments and controls

the O/D OFF indicator light blinks for

approximately 8 seconds after coming on for 2 seconds, have your NISSAN dealer check the transmission and repair it if necessary.

it may indicate there is something wrong with the cruise control system. Have the system checked by your NISSAN dealer.

The automatic transmission is equipped with an electronic Fail-Safe mode. This system allows the vehicle to be driven even in the event of damage to the electrical circuits. If this occurs, the gears automatically engage and lock into 3rd gear. See “Driving the vehicle” in the “5. Starting and driving” section for failsafe before vis- iting your NISSAN dealer.

Turn signal/hazard indicator lights

The light flashes when the turn signal switch lever or hazard switch is turned on.

High beam indicator light (Blue)

This light comes on when the headlight high beam is on, and goes out when the low beams are selected.

CRUISE indicator light

The light comes on while the vehicle speed is controlled by the cruise control system. If the light flickers while the engine is running,

Malfunction indicator light (MIL)

If the Malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control prob- lem.

The Malfunction indicator light will come on in one of two ways: I Malfunction indicator light on steady — An emission control system malfunction has been detected. Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

I Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage: * do not drive at speeds above 45 MPH (72

km/h).

* avoid hard acceleration or deceleration. * avoid steep uphill grades. * if possible, reduce the amount of cargo

Z 01.1.31/R50-D X

is moving, whether or not the brake pedal is depressed.

being hauled or towed.

The malfunction indicator light may stop blink- ing and come on steady.

Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Some conditions may cause the malfunction indicator light to come on steady or blink. Examples are as follows: I vehicle ran out of fuel, which caused the

engine to misfire.

I fuel

filler cap was left off or improperly installed, allowing fuel to evaporate into the atmosphere.

If you suspect that you experienced one or both of the above conditions, drive the vehicle to an authorized NISSAN dealer and have the

vehicle inspected. Avoid any unnecessary di- agnosis during the service by informing the dealer of the conditions listed above that may have occurred.

Four wheel drive indicator light

This light comes on when the transfer shift control lever is in the 4H or 4L position. BUZZERS Key reminder buzzer The buzzer will sound when the driver side door is opened if the key is left in the ignition switch. Take the ignition key when you leave the vehicle. Light reminder buzzer A buzzer will sound if the driver’s door is opened with the light switch on unless the ignition key in the ON position. Turn the light switch off when you leave the vehicle. Brake pad wear warning The disc brake pads have audible wear warn- ings. When a brake pad requires replacement, it will make a high pitched scraping sound. Have the brakes checked as soon as possible if the warning sound is heard when the vehicle

Instruments and controls 2-13

Z 01.1.31/R50-D X

SECURITY SYSTEM

locked and ignition key off. Turn the ignition key to ACC to turn the system off.

How to activate the theft warning system 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close and lock all doors, hood, back door and glass hatch. The doors can be locked either with or without the key.

IC0005

THEFT WARNING The theft warning system provides visual and audio alarm signals if parts of the vehicle are disturbed.

2-14 Instruments and controls

SIC0603

The system can be activated even if the windows are open.

Security indicator light I If the key is turned slowly toward the front of the vehicle when locking the door, the system may not activate. If the key is returned beyond the vertical po- sition toward the rear of the vehicle to remove the key, the system may be deactivated. When the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.

I Even when the driver and/or passengers are in the vehicle, the system will acti- vate with all doors, hood and back door

4. Confirm that the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then begins to flash. The system is now activated. If, during this 30 second time period, the door is unlocked by the key or multi-remote controller, or the ignition key is turned to ACC or ON, the system will not activate.

THEFT WARNING SYSTEM OPERATION The warning system will give the following alarm:

Z 01.1.31/R50-D X

WINDSHIELD WIPER AND WASHER SWITCH

I The headlights blink and the horn sounds intermittently. In addition, the starter motor will not operate.

I The alarm automatically turns off after 2 to 3 minutes; however, the alarm will reacti- vate if the vehicle is tampered with again.

The alarm is activated by: I Unlocking the door, back door or back door glass hatch without using the key or multi- remote controller. is opened by releasing the door inside lock knob, the alarm is activated.)

the door

(Even if

I Opening the hood. How to stop alarm The alarm will stop only by unlocking a door or back door with the key or multi-remote control- ler. The alarm will not stop if the ignition switch is turned to ACC. If the system does not operate as de- scribed above, have it checked by your NISSAN dealer.

SIC0683

The windshield wiper and washer operates when the ignition key is in the ACC or ON position. Push the lever down to operate the wiper. Intermittent operation can be adjusted from 4
to 12 seconds by turning the knob. Pull toward you to operate the washer. Then the wiper will also operate sev- eral times.

the lever

The following could damage the washer system: I Do not operate the washer continu-

ously for more than 30 seconds.

I Do not operate the washer if the res-

ervoir tank is empty.

In freezing temperatures the washer so- lution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.

Instruments and controls 2-15

Z 01.1.31/R50-D X

REAR WINDOW WIPER AND WASHER SWITCH

REAR WINDOW AND OUTSIDE MIRROR DEFOGGER SWITCH

I Do not operate the washer continu-

ously for more than 30 seconds.

I Do not operate the washer if reservoir

tank is empty.

I The rear window wiper will not operate

when the rear window is open.

The rear window wiper will not operate if the rear window is closed with the wiper switch on. To operate the window wiper, turn the switch to off and then to on.

I The rear window will not open while the

rear window wiper is operating.

In freezing temperatures the washer so- lution may freeze on the rear window and obscure your vision. Warm the rear window with the defroster before you wash the rear window.

SIC0593

To defog the rear window glass and the out- side door mirrors, start the engine and push the switch on. (The indicator light will come on.) Push the switch again to turn the defogger off. It will automatically turn off in approximately 15
minutes. If the window clears before this time, push the switch off manually.

SIC0548

To operate the wiper, push the switch to the side. This wiper operates intermittently. side fully, this

Push the switch to the operates the wiper continuously. To operate the washer, hold the switch down to the Then the wiper will also operate several times.

side.

2-16 Instruments and controls

Z 01.1.31/R50-D X

HEADLIGHT AND TURN SIGNAL SWITCH

When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defogger.

HEADLIGHT SWITCH Lighting Turn the switch to the

position:

The side combination, tail, license plate and

SIC0188

instrument lights will come on. Turn the switch to the Headlights will come on and all the other lights remain on.

position:

Instruments and controls 2-17

Z 01.1.31/R50-D X

To select the high beam, push the lever for- ward. Pull it back to select the low beam.

Passing signal Pulling the lever toward you will turn on the passing signal even when the headlight switch is off. TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal to the turning direction. When the turn is completed, the turn signals cancel automatically. Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flash- ing. Daytime running light system (For Canada) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the off position or in the position. Turn the headlight switch to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate.

SIC0052

Instrument brightness control The instrument brightness control operates when the light switch is in the or

position.

Turn the control to adjust the brightness of instrument panel lights and power window switch lights. When the control is turned to the right until a click sound is heard, the light intensity will be at maximum. When the control is turned to the left until a click sound is heard, the light will be turned off.

2-18 Instruments and controls

Z 01.1.31/R50-D X

The daytime running lights illuminate once the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is turned off.

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

FRONT FOG LIGHT SWITCH

HAZARD WARNING FLASHER SWITCH

IC1292

SIC0594

position,

To turn the fog lights on, turn the headlight switch to the then turn the switch to the position. To turn them off, turn the switch to the OFF position. The headlights must be on for the fog lights to operate.

Push the switch on to warn other drivers when you must stop or park under emergency con- ditions. All turn signal lights will flash. Some state laws may prohibit the use of the hazard warning flasher switch while driv- ing.

I When stalled or stopped on the road- way under emergency conditions, move the vehicle well off the road.

Instruments and controls 2-19

Z 01.1.31/R50-D X

HORN

HEATED SEATS (if so equipped)

I Do not use the switch while moving on the highway unless unusual cir- cumstances force you to drive so slowly that your vehicle might be- come a hazard to other traffic.

I Turn signals do not work when the

switch is operating.

The flasher can be actuated with the ignition switch either off or on.

SIC0861

SIC0684

To sound the horn, push the center pad area of the steering wheel.

The front seat(s) are warmed by built-in heat- ers. The switches located on the instrument panel can be operated independently of each other. 1. Start the engine. The battery could run down if the heater is operated while the engine is not running.

2. Push the

(Low) or

(High) po- sition of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off.

2-20 Instruments and controls

Z 01.1.31/R50-D X

The indicator light will remain on as long as the switch is on.

3. When the vehicle’s interior is warmed or before you leave the vehicle, be sure to turn the switch off.

I If any abnormalities are found or the heating seat does not operate, turn the switch OFF and have the system checked by your NISSAN dealer.

POWER SOCKET

I Do not use the seat heater for ex- tended periods or when no one is using the seat.

I Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.

I Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

I Any liquid spilled on the heating seat should be removed immediately with a dry cloth.

I When cleaning the seat, never use benzine, thinner, or any similar mate- rials.

SIC0686

I Take care as the socket and plug may be hot during or immediately after use.

I This power socket is not designed for

use with a cigarette lighter unit.

I Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

Instruments and controls 2-21

Z 01.1.31/R50-D X

CIGARETTE LIGHTER AND ASHTRAYS

I Use this power socket with the en- the engine is gine running. stopped, this could result in a dis- charged battery.)

(If

I Avoid using when the air conditioner, headlights or rear window defogger is on.

I Before inserting or disconnecting a plug, be sure to turn off the power switch of electrical accessory being used or the ACC power of the vehicle. I Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tempera- ture fuse may blow.

I When not in use, be sure to close the cap. Do not allow water to contact the socket.

2-22 Instruments and controls

The cigarette lighter operates when the igni- tion switch is in ACC or ON. Push the lighter in all the way. When the lighter is heated, it will spring out. Replace the lighter in its original position after use.

The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation.

The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.

SIC0685

Z 01.1.31/R50-D X

STORAGE

I Do not use for anything other than

glasses.

I Do not leave glasses in the glasses case while parking in direct sunlight. The heat may damage the glasses.

TRAY

SIC0596

SIC0557

GLASSES CASE The glasses case can be opened by pushing the button.

The coin tray should not be used while driving in order that full attention may be given to the driving operation.

Do not place valuable items in the tray.

The glasses case should not be used while driving in order that full attention may be given to the driving operation.

Instruments and controls 2-23

Z 01.1.31/R50-D X

is hot, it can scald you or your pas- senger.

I Use only soft cups in the cup holder. Hard objects can injure you in an accident.

SIC0553

SIC0698

CUP HOLDERS

The cup holders should not be used while driving in order that full attention may be given to the driving operation.

I Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid

2-24 Instruments and controls

To open, push the cup holder. To close, fully push the cup holder.

Z 01.1.31/R50-D X

CONSOLE BOX

I The center console box should not be used while driving in order that full attention may be given to the driving operation.

I Keep the center console box lid closed while driving to prevent injury in an accident or a sudden stop.

Do not place valuable items in the center console box.

SPA0388

GLOVE BOX When locking or unlocking the glove box, use the master key. The glove box may be opened by the handle.

Keep glove box lid closed while driving to help prevent injury in an accident or during a sudden stop.

SIC0688
Instruments and controls 2-25

Z 01.1.31/R50-D X

LUGGAGE STORAGE

Keep luggage side console box lids closed securely while driving to prevent injury in an accident or sudden stop.

Do not place valuable items in the luggage side console box.

2-26 Instruments and controls

SIC0598

SPA0346A

I Make sure the luggage board closes

securely.

I Do not drive with the board removed.

Z 01.1.31/R50-D X

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

I Never allow anyone to ride in the luggage area or on the rear seat when it is in the fold-down position.

I It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

I Do not allow people to ride in any is not

area of your vehicle that equipped with seats and seat belts.

LUGGAGE HOOKS The luggage hooks can be used to secure cargo with ropes or other types of straps.

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

I Use the suitable ropes and hooks to

secure cargo.

I Never allow anyone to ride in the luggage area. It is extremely danger- ous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

I Do not allow people to ride in any is not

area of your vehicle that equipped with seats and seat belts. I Be sure everyone in your vehicle is in a seat and using a seat belt properly.

SPA0408A

Side finisher I When hooking on ropes, do not apply a load of more than 22 lb (98 N) to a single hook.

I Do not use the luggage net between the

A and B hooks.

Instruments and controls 2-27

Z 01.1.31/R50-D X

Floor

SPA0365

SPA0396

LUGGAGE NET (if so equipped) The luggage net keeps packages in the cargo area from moving around while your vehicle is driven. To install hooks to the four retainers. To remove the luggage net, detach the four hooks from the luggage net retainers.

the luggage net, attach the four

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

I Be sure to secure all four hooks into the retainers. The cargo restrained in the net must not exceed 30 lbs. (13.6
kg) or the net may not stay secured.

2-28 Instruments and controls

Z 01.1.31/R50-D X

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

SPA0419

TONNEAU COVER The tonneau cover keeps the luggage com- partment contents hidden from the outside.

I Never put anything on the tonneau cover, no matter how small. Any ob- ject on it could cause an injury in an accident or sudden stop.

I Do not leave the tonneau cover in the vehicle with it disengaged from the holder.

Instruments and controls 2-29

Z 01.1.31/R50-D X

WINDOWS

LUGGAGE RACK (if so equipped) The cross-bars can be adjusted forward and backward. Place your luggage between the bars (A), adjust the bars (A), and secure the luggage with rope to the bars (A). There are also adjustable loops on the side bars for the rope attachment. Always evenly distribute the luggage on the luggage rack. Do not load more than 100 lb (45 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the Safety Compliance 2-30 Instruments and controls

SPA0397

SIC0599B

Certification Label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, refer to “10. Technical and cus- tomer information”.

POWER WINDOWS

Use care when placing or removing items from the luggage rack. If you can- not comfortably lift the items onto the luggage rack from the ground, use a ladder or stool.

I Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.

I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls and become trapped in a window.

Z 01.1.31/R50-D X

Unattended children could become involved in serious accidents.

The power window only operates when the ignition key is in the ON position. To open or close the window, push down or pull up the switch and hold it. The main switch (driver side switches) will open or close all the windows. Locking passenger’s window When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.

SIC0600B

SIC0559

The passenger side switch will open or close only the corresponding window. To open or close the window, hold the switch down or up.

Instruments and controls 2-31

Z 01.1.31/R50-D X

SUNROOF (if so equipped)

SIC0601

SIC0560

Automatic operation To fully open the driver side window, com- pletely push down the switch and release it; it need not be held. The window will automati- cally open all the way. To stop the window, just pull up the switch toward the close side. A light press on the switch will cause the window to open until the switch is released.

2-32 Instruments and controls

AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position. Sliding the sunroof To open the roof, keep pressing the switch to the

side.

side.

To close the roof, keep pressing the switch to the Tilting the sunroof To tilt up, first close the sunroof, then keep pushing the

side of the tilt switch.

SIC0561

To tilt down the sunroof, keep pushing the

side.

Sun shade Open/close the sun shade by sliding it backward/forward.

Z 01.1.31/R50-D X

The shade will open automatically when the sunroof is opened. However, it must be closed manually.

If the sunroof does not close Have your NISSAN dealer check and repair the sunroof.

CLOCK

I In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.

I Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is closing.

I Remove water drops, snow,

ice or sand from the sunroof before open- ing.

I Do not place any heavy object on the

sunroof or surrounding area.

SIC0884

The digital clock displays time when the igni- tion key is in ACC or ON. If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time. ADJUSTING THE TIME Depressing or pressing

buttons together will set hours. De- or

the CLOCK and

CLOCK

and

the

the

buttons together will set minutes.

Instruments and controls 2-33

Z 01.1.31/R50-D X

INTERIOR LIGHT

interior light will not illuminate, regardless of door position.

I When the switch is in the center q position, illuminate when a door is

the light will opened.

I When the switch is in the ON position, the illuminate, whether any

interior light will door is open or closed.

Leaving the interior light switch in the ON position for extended periods of time will result in a discharged battery.

SIC0564

The interior light has a three position switch.

The interior light will operate regardless of ignition key position. I When the switch is in the OFF position, the

Z 01.1.31/R50-D X

SIC0691

CLOCK OPERATION By pressing the CLOCK button, you can alter- nate the clock and the radio/cassette tape options in the display. CLOCK PRIORITY MODE In this mode the clock will be shown in the display. If any radio or cassette tape functions are activated, the radio, cassette or CD display will illuminate for ten seconds then return to the clock mode. After clock adjustment, the radio is in the clock priority mode.

2-34 Instruments and controls

PERSONAL LIGHT

VANITY MIRROR LIGHT

SIC0565

SIC0186

The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.

Do not use for extended periods of time with the engine stopped. This could re- sult in a discharged battery.

INTEGRATED HomeLink TRANSMITTER (if so equipped) The Integrated HomeLink Transmitter pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. I The Integrated HomeLink Transmitter will operate garage doors, gates, home/ office lighting systems and security sys- tems by storing and transmitting the pro- gramming information of your current hand- held transmitters.

I The Integrated HomeLink

Transmitter is built-in and powered by your vehicle’s battery and charging system. No separate batteries are necessary.

Do not use this Integrated HomeLink Transmitter with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards (these standards be- came effective for models manufactured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse the door, does not meet current federal safety standards. Using a garage door Instruments and controls 2-35

Z 01.1.31/R50-D X

opener without these features increases the risk of serious injury or death.

PROGRAMMING THE HomeLink TRANSMITTER

SIC0602

During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.

Your vehicle’s engine should be turned off while programming your transmitter.

The Integrated HomeLink Transmitter may not work with older garage door openers that do not meet current Fed- eral Consumer Safety Standards.

1. Test the Integrated HomeLink Transmitter by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3.

2. Clear all channels on the Integrated HomeLink Transmitter by holding down both outside buttons (#1 & #3) until the red light begins to flash rapidly (approximately 20 seconds). Then release both buttons.

3. Select which of

the three Integrated HomeLink Transmitter buttons you want to program.

4. Hold your hand-held transmitter against the bottom surface Integrated HomeLink Transmitter so that you can still see the red indicator light.

the

of

5. Press the desired button until the red indi- cator light flashes slowly. Do not release the button. Continue holding and press the hand-held transmitter button through step 6.

2-36 Instruments and controls

Z 01.1.31/R50-D X

6. Hold

until

buttons

Transmitter

both the down light on the Integrated red indicator HomeLink flashes rapidly (This may take 1 to 90 seconds). Then release both buttons. The rapid flashing means that the transmitter has been suc- cessfully programmed to match your hand- held transmitter. You can now use the Integrated HomeLink Transmitter instead of your hand-held transmitter.

Note to Canadian users:

to 1992, D.O.C.

Prior regulations required many hand-held transmitters to stop transmit- ting after one or two seconds, even though you continue to hold down the button. If you think you have one of these hand-held transmitters, you should press and re-press the transmitter button every 2 seconds without ever releasing the integrated HomeLink Transmitter button. The Integrated HomeLink Transmitter should blink rapidly indicating a successful programming proce- dure. If it returns to the slow blink of program mode, continue to periodically reactivate your hand-held transmitter until a successful pro- gramming procedure is indicated by the rapidly flashing indicator light.

indicator

light

the

on

I Rotate your hand-held transmitter end- over-end and program again. For best re- sults, place the end opposite the battery compartment Integrated Transmitter when program- HomeLink ming.

against

the

OPERATING THE TRANSMITTER To operate, simply press the appropriate but- ton on the Integrated HomeLink Transmitter. The red indicator light illuminates while the signal is being transmitted. The effective trans- mission range of the Integrated HomeLink Transmitter may differ from your hand-held transmitter. PROGRAMMING PROBLEM DIAGNOSIS Be sure to keep your original hand-held trans- mitter for possible reprogramming if neces- sary. I Make sure batteries in the hand-held trans-

mitter are fully charged.

I Hold your hand-held transmitter against the bottom surface Integrated HomeLink Transmitter so that you can still see the red indicator light.

the

of

I Hold buttons for duration of the program-

ming without interruption.

Instruments and controls 2-37

Z 01.1.31/R50-D X

flashes rapidly for 1 to 2 seconds, then re- mains on, your garage door opener has a rolling code system.

To operate your Rolling Code garage door opener from your HomeLink Transmitter, fol- low these steps:

1. Program your hand held transmitter to the HomeLink Transmitter by following the procedures outlined above (if not yet pro- grammed).

2. Program your garage door opener receiver to recognize your HomeLink Transmitter (The HomeLink Transmitter follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed):

a) Remove the cover panel from your ga- rage door opener receiver. The receiver should be located by the garage door opener motor.

b) Locate the training button on the garage door opener receiver. The exact location and color of the button may vary by garage door opener brand. If you have difficulty locating the training button, ref- erence opener manual. If you have difficulty program- ming your garage door opener equipped

garage

door

your

with a rolling code system to recognize Transmitter with the the HomeLink Rolling Code feature, call NISSAN Con- sumer Affairs Department.

c) Press the training button on the garage door opener receiver for 1 to 2 seconds.

d) Return to the HomeLink Transmitter in the vehicle, and depress the pro- grammed HomeLink button for the du- ration of the fast blink on the HomeLink Transmitter (1 to 2 seconds). Release the button, and re-press to confirm that the system has trained.

e) Your garage door opener should now recognize your HomeLink Transmitter. You may use either your HomeLink Transmitter or your original hand held transmitter to open your garage door. CLEARING THE PROGRAMMING INFORMATION Should you sell your vehicle, be sure to clear the channels of the Integrated HomeLink Transmitter. To clear the channels, simulta- neously hold down the outside two buttons (#1
& #3) until the red indicator light begins to flash rapidly (approximately 20 seconds). This will clear all three buttons. Individual buttons can- not be cleared, but can be reprogrammed at

Z 01.1.31/R50-D X

SPA0609

ROLLING CODES (if so equipped) If your hand held transmitter appears to train to the HomeLink Transmitter, but does not open your garage door, and your garage door opener was manufactured after 1995, your garage door opener may have a Code Pro- tected or Rolling Code feature. This type of system will change the code of your garage door opener every time you open or close your garage door. To determine if you have one of these sys- tems, depress the button on the HomeLink Transmitter that you have just programmed. If the LED on the HomeLink Transmitter 2-38 Instruments and controls

pliance could void the user’s authority to operate the device. DOC: ISTC 1763K1313
FCC I.D.: CB2V67690

programmed

any time by following the programming proce- dures described above. IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was Integrated HomeLink Transmitter as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those de- vices. When your vehicle is recovered, you will have to reprogram the Integrated HomeLink Transmitter with your new transmitter information.

into

the

FCC Notice:

This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for com-

Instruments and controls 2-39

Z 01.1.31/R50-D X

MEMO

2-40 Instruments and controls

Z 01.1.31/R50-D X

3 Pre-driving checks and adjustments

Keys .......................................................................... 3-2
Doors......................................................................... 3-2
Multi-remote control system (if so equipped)............ 3-4
Hood.......................................................................... 3-8
Back door .................................................................. 3-9
Spare tire carrier ....................................................... 3-9
Rear window ........................................................... 3-10
Fuel filler lid............................................................. 3-11
steering wheel ......................................................... 3-13
Sun visors ............................................................... 3-13
Mirrors ..................................................................... 3-14

Z 01.1.31/R50-D X

KEYS

DOORS

I Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.

I Before opening any door, always look

for and avoid oncoming traffic.

I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.

SPA0383

LOCKING WITH KEY To lock the door, turn the key towards the front of the vehicle. To unlock, turn it towards the rear.

Z 01.1.31/R50-D X

SPA0651

The key can only be inserted fully in the ignition key cylinder. For the door, back door and glove box key cylinders, it is normal for the key not to go into the key cylinder all the way. Record the key number on the key number plate and keep it in a safe place (such as your wallet), NOT IN THE CAR. A key number plate is supplied with your key. Keep the plate in a safe place. NISSAN does not record key num- bers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer or a lock smith shop.

3-2 Pre-driving checks and adjustments

PD1160M

SPA0384B

IC1156M

LOCKING WITH INSIDE LOCK KNOB To lock from the outside without a key, move the inside lock knob to the lock position. Then close the door. When locking the door this way, be certain not to leave the key inside the vehicle.

LOCKING WITH POWER DOOR LOCK SWITCH The power door lock system allows you to lock or unlock all doors simultaneously. Operating the lock-unlock switch will unlock all doors including the back door.

lock or

CHILD SAFETY REAR DOOR LOCK Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, the rear door can be opened only from the outside.

Pre-driving checks and adjustments 3-3

Z 01.1.31/R50-D X

HOW TO USE MULTI-REMOTE CONTROL SYSTEM Locking doors 1. Remove the ignition key. 2. Close all the doors. 3. Push the controller.

button on the multi-remote

4. All the doors will lock. 5. The hazard indicator flashes twice. I When the

button is pushed with all doors locked, the hazard indicator flashes twice as a reminder that the doors are already locked.

MULTI-REMOTE CONTROL SYSTEM (if so equipped) It is possible to lock/unlock all doors including the back door. Be sure to remove the key from the vehicle before locking the doors and leaving it. The remote controller can operate at a dis- tance of approximately 49 ft (15 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact your NISSAN dealer.

Listed below are conditions or occur- rences which will damage the remote controller. I Do not allow the remote controller to

become wet.

I Do not drop the remote controller. I Do not strike the remote controller

sharply against another object.

I Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).

3-4 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

The interior light can be turned off without waiting for 30 seconds by inserting the key into the ignition or by locking the doors with the multi-remote controller or by pushing the inte- rior light button. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the alarm to call atten- tion as follows:

1. Push the

button on the remote control-

ler for longer than 1.5 seconds.

Unlocking doors 1. Push the

button on the multi-remote controller. Only the driver side door will unlock.

2. Push the

button on the multi-remote

controller again within 5 seconds. All doors will unlock.

3. The interior light will stay on for 30 seconds when the interior light switch is in the center q position.

SPA0398

2. The theft warning alarm and headlights will

stay on for 30 seconds.

or the

3. The alarm will stop when any of the key functions are used. For example, when the button is pushed, or the button is pushed for longer than 1.5
seconds on the multi-remote controller, the panic alarm function will be cancelled. The remote controller will not function. I When the key is inserted into the key

switch.

I When the battery in the remote control-

ler is dead.

I The distance between the remote con- Pre-driving checks and adjustments 3-5

Z 01.1.31/R50-D X

troller and vehicle is more than approx. 49 ft (15 m).

I When one of the doors is ajar, only the

unlock function can be operated.

BATTERY REPLACEMENT Replace the battery as follows:

1. Open the lid using a coin.

2. Replace the battery with a new one. Insert

SPA0650

the battery as illustrated above.

Recommended battery: Sanyo CR2025
or equivalent.

3. Close the lid securely.

3-6 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

4. Press the

button,

then the

button two or three times to check the multi-remote controller operation.

If the battery is removed for any reason other than replacement, perform step 4
above. I An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal.

I The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry.

I When changing battery, do not let dust

or oil get on the controller.

FCC Notice:

Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference and (2) this de- vice must accept any interference received, including interference that may cause un- desired operation of the device.

Pre-driving checks and adjustments 3-7

Z 01.1.31/R50-D X

HOOD

from the engine compartment, avoid injury do not open the hood.

to

1. Pull the hood lock release handle located below the instrument panel; the hood will then spring up slightly.

2. Raise the lever at the front of the hood with

your fingertips and raise the hood.

3. Insert the assist bar into the slot in the front

edge of the hood.

4. When closing the hood, reset the assist bar to its original position, then slowly close the hood and make sure it locks into place.

SPA0387

I Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. I If you see steam or smoke coming

3-8 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

BACK DOOR

SPARE TIRE CARRIER

I Do not drive with the back door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “5. Starting and driv- ing” section for exhaust gas.

SPA0462

KEY OPERATION 1. Turn the key counterclockwise to unlock the

back door.

2. Pull the opener handle to open the back

door.

3. To lock the back door, push it down firmly

and turn the key clockwise.

I Always check the back door has been closed securely to prevent it from opening while driving.

SPA0385

When opening the back door, first open the spare tire carrier in the sequence shown in the illustration above. Then insert the stopper into the hole to secure the carrier in the open position.

I Be certain that there is adequate area

to allow the carrier to open fully.

I Open and close the spare tire carrier

slowly.

Pre-driving checks and adjustments 3-9

Z 01.1.31/R50-D X

REAR WINDOW

Do not open the rear window unless the wiper is in the stowed position.

SPA0386

SPA0338

I Before driving, be certain that the spare tire carrier is firmly closed and latched.

I Failure to do so may injure pedestri-

ans or damage the vehicle.

To open the rear window, turn the key fully clockwise and pull the opener handle. To close, lower and push the rear window down securely.

Do not drive with the rear window open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas.

3-10 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

FUEL FILLER LID

SPA0341

FUEL FILLER CAP The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard.

SPA0389

OPENER OPERATION Opener lever To open the fuel filler lid, push the opener lever down. To lock, close the fuel filler lid securely.

I Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seri- ously injured if it is misused or mis- handled. Always stop the engine and do not smoke or allow open flames or

sparks near the vehicle when refuel- ing.

I Fuel may be under pressure. Turn the cap one-half turn, and wait for any hissing sound to stop to prevent fuel from spraying out and possible per- sonal injury. Then remove the cap.

I Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel over-flow, resulting in fuel spray and possibly a fire.

I Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper opera- tion of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury.

I Never pour fuel into the throttle body

to attempt to start your vehicle.

Pre-driving checks and adjustments 3-11

Z 01.1.31/R50-D X

I If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

I Tighten until cap clicks, failure to tighten fuel cap properly may cause the malfunction indicator light (MIL) to illuminate. If this occurs, it will be necessary to take your vehicle in for service by an authorized NISSAN dealer.

Put the fuel filler cap on the cap holder while refueling.

SPA0342

3-12 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

STEERING WHEEL

SUN VISORS

USING THE SUN VISORS 1. To block out glare from the front, swing

down the main sun visor.

2. To block glare from the side, remove the main sun visor from the center mount and swing it to the side.

3. Then,

to block glare from the front

too,

swing down the sub-sun visor.

SPA0394

TILT OPERATION While pushing down on the lock lever, adjust the steering wheel up or down to the desired position. Push the lock lever up securely to lock the steering wheel in place.

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

4. To adjust the glare block position, slide the

sub-sun visor to the left.

I Do not store the main sun visor be-

fore storing the sub-sun visor.

I Do not pull the sub-sun visor forcedly

downwards.

SPA0395

Pre-driving checks and adjustments 3-13

Z 01.1.31/R50-D X

MIRRORS

PD1006M

SPA0112A

PD1183MB

INSIDE MIRROR The night position will reduce glare from the headlights of vehicles behind you at night.

OUTSIDE MIRRORS Push the right or left end of the switch to adjust the right or left side mirror, then control the lever.

Use the night position only when neces- sary, because it reduces rear view clarity.

3-14 Pre-driving checks and adjustments

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use inside mirror or glance over your shoulder to properly judge distances to other objects.

Z 01.1.31/R50-D X

The outside mirror can be moved in any direc- tion for a better rear view.

FOLDING OUTSIDE MIRROR Push the mirror backward to fold it.

M008

Pre-driving checks and adjustments 3-15

Z 01.1.31/R50-D X

MEMO

3-16 Pre-driving checks and adjustments

Z 01.1.31/R50-D X

4 Heater, air conditioner and audio systems

Ventilators ................................................................. 4-2
Heater and air conditioner (Manual) ......................... 4-3
Heater and air conditioner (Semiautomatic) ............. 4-9
Servicing air conditioner.......................................... 4-13
Audio system........................................................... 4-14
CB radio or car phone ............................................ 4-26

Z 01.1.31/R50-D X

VENTILATORS

Open or close, and adjust the air flow direction of ventilators.

: This symbol indicates that the vents are closed when the vent switch is moved to the left.

: This symbol indicates that the vents are open when the vent switch is moved to the right.

4-2 Heater, air conditioner and audio systems

SAA0159

Z 01.1.31/R50-D X

HEATER AND AIR CONDITIONER (Manual)

SAA0152B

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full atten- tion may be given to the driving operation.

I The air conditioner cooling function operates only when the engine is run- ning.

I Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

CONTROLS Fan control dial This dial turns the fan on and off, and controls fan speed. Air flow control dial This dial allows you to select outlets.

the air flow

— Air flows from center and side venti-

lators.

— Air flows from center and side venti-

lators and foot outlets.

— Air flows mainly from foot outlets. — Air flows from defroster outlets and

foot outlets.

— Air flows mainly from defroster out-

lets.

Temperature control dial This dial allows you to adjust the temperature of the outlet air.

Heater, air conditioner and audio systems 4-3

Z 01.1.31/R50-D X

Air recirculation button Off position Outside air is drawn into the passenger com- partment. Use the off position for normal heater, or air conditioner operation. On position (Indicator light on) Interior air is recirculated inside the vehicle. Push the air recirculation button to the on position when driving on a dusty road or to avoid traffic fumes. Air conditioner button This button is provided only for vehicles with air conditioner. Start the engine, move the fan control dial to the desired (1 to 4) position and push the air conditioner button to turn on the air condi- tioner. The indicator light will come on when the air conditioner button is on. To stop the air conditioner, push the switch again to return it to the original position. The air conditioner cooling function oper- ates only when the engine is running.

4-4 Heater, air conditioner and audio systems

HEATER OPERATION Heating This mode is used to direct hot air from the floor outlets.

1. Push the air recirculation button to the off

position for normal heating.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the desired position between the middle and the hot position.

I For quick heating, move the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal heating.

Ventilation This mode directs outside air from the side and centre vents.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

position.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the

desired position.

Defrosting or defogging This mode is used to defrost/defog the win- dows.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the desired position between the middle and the hot position.

I To quickly remove ice or fog from the windows, push the air recirculation button to the on position, the fan control dial to 4
and the temperature control dial to the full hot position. As soon as possible after the window is clear, push the air recirculation button to the off position.

Bi-level heating This mode directs outside air from the side and center vents and hot air from the floor outlets. 1. Push the air recirculation button to the off

position.

Z 01.1.31/R50-D X

2. Turn the air control dial to the

tion.

posi-

3. Turn on the fan control dial. 4. Normally turn the temperature control dial

to the midpoint between hot and cold.

Heating and defogging This mode heats the interior and defogs the windscreen. 1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

tion.

posi-

3. Turn on the fan control dial. 4. Turn the temperature control dial

to the desired position between the middle and the hot position.

Operating tips I Clear snow and ice from the wiper blade and air inlet in front of the windshield. This will improve heater operation.

I A slight delay may be experienced when turning the air control dial. This is not a problem, it is only the system motors and solenoids switching from one outlet to an- other.

AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (1 to 4) position and push in the air conditioner button to activate the air condi- tioner. When the air conditioner is on, cooling and dehumidifying functions will be added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

position.

3. Turn on the fan control dial.

4. Push on the air conditioner button. The

indicator light will come on.

5. Turn the temperature control dial

to the

desired position.

I For quick cooling when the outside tem- perature is high, push the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal cooling.

Dehumidified heating This mode is used to heat and dehumidify.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Push on the air conditioner button. The

indicator light will come on.

5. Turn the temperature control dial

to the

desired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Push on the air conditioner button. The

indicator light will come on.

5. Turn the temperature control dial

to the

desired position.

Heater, air conditioner and audio systems 4-5

Z 01.1.31/R50-D X

Operating tips I Keep windows and sun roof closed while

the air conditioner is in operation.

I After parking in the sun, drive for two or