1997 Nissan Pathfinder Owners Manual

slowly that your vehicle might be- come a hazard to other traffic.

I Turn signals do not work when the

switch is operating.

The flasher can be actuated with the ignition switch either off or on.

IC1292

SIC0594

To turn the fog lights on, turn the headlight switch to the “ ” position, then turn the switch to the “ ” position. To turn them off, turn the switch to the “OFF” position. The headlights must be on for the fog lights to operate.

Push the switch on to warn other drivers when you must stop or park under emergency con- ditions. All turn signal lights will flash. Some state laws may prohibit the use of the hazard warning flasher switch while driv- ing.

I When stalled or stopped on the road- way under emergency conditions, move the vehicle well off the road.

I Do not use the switch while moving

1-19

Z 01.2.1/R50-D X

HEATED SEATS (If so equipped)

The indicator light will remain on as long as the switch is on.

the switch OFF and have the system checked by your NISSAN dealer.

3. When the vehicle’s interior is warmed or before you leave the vehicle, be sure to turn the switch off.

SIC0684

The front seat(s) are warmed by built-in heat- ers. The switches located on the instrument panel can be operated independently of each other.

1. Start the engine. The battery could run down if the heater is operated while the engine is not running.

2. Push the “

” (Low) or “

” (High) position of the switch, as desired, depend- ing on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off.

I Do not use the seat heater for a long time or when no one is seated there. I Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.

I Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

I Any liquid spilled on the heating seat should be immediately wiped up with a dry cloth.

I When cleaning the seat, never use benzine, thinner, or any similar mate- rials.

I If any abnormalities are found or the heating seat does not operate, turn

1-20

Z 01.2.1/R50-D X

CIGARETTE LIGHTER AND ASH TRAYS

The cigarette lighter operates when the igni- tion switch is in “ACC” or “ON”. Push the lighter in all the way. When the lighter is heated, it will spring out. Replace the lighter in its original position after use.

The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation.

The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.

SIC0685

1-21

Z 01.2.1/R50-D X

POWER SOCKET

COIN TRAY

I Use this power socket with the en- gine running. the engine is stopped, this could result in a dis- charged battery.)

(If

I Avoid using when the air conditioner, headlights or rear window defogger is on.

I Before inserting or disconnecting a plug, be sure to turn off the power switch of electrical accessory being used or the ACC power of the vehicle. I Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tempera- ture fuse may blow.

I When not in use, be sure to close the cap. Do not allow water to contact the socket.

SIC0596

The coin tray should not be used while driving in order that full attention may be given to the driving operation.

Do not place valuable items in the tray.

1-22

Z 01.2.1/R50-D X

SIC0686

I Take care as the socket and plug may be hot during or immediately after use.

I This power socket is not designed for

use with a cigarette lighter unit.

I Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

CUP HOLDER

is hot, it can scald you or your pas- senger.

I Use only soft cups in the cup holder. Hard objects can injure you in an accident.

SIC0553

SIC0698

To open, push the cup holder. To close, fully push the cup holder.

The cup holders should not be used while driving in order that full attention may be given to the driving operation.

I Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid

1-23

Z 01.2.1/R50-D X

GLASSES CASE

CONSOLE BOX

I Do not use for anything other than

glasses.

I Do not leave glasses in the glasses case while parking in direct sunlight. The heat may damage the glasses.

The glasses case can be opened by pushing the button.

SIC0557

The glasses case should not be used while driving in order that full attention may be given to the driving operation.

1-24

SIC0688

Z 01.2.1/R50-D X

I The center console box should not be used while driving in order that full attention may be given to the driving operation.

I Keep the center console box lid closed while driving to prevent injury in an accident or a sudden stop.

Do not place valuable items in the center console box.

Keep luggage side console box lids closed securely while driving to prevent injury in an accident or sudden stop.

Do not place valuable items in the luggage side console box.

SIC0598

1-25

Z 01.2.1/R50-D X

LUGGAGE BOARD AND BOX

TONNEAU COVER

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

I Never allow anyone to ride in the luggage area or on the rear seat when it is in the fold-down position.

I It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

I Do not allow people to ride in any is not

area of your vehicle that equipped with seats and seat belts.

The tonneau cover keeps the luggage com- partment contents hidden from the outside.

SPA0419

SPA0346A

I Make sure the luggage board closes

securely.

I Do not drive with the board removed.

I Never put anything on the tonneau cover, no matter how small. Any ob- ject on it could cause an injury in an accident or sudden stop.

I Do not leave the tonneau cover in the vehicle with it disengaged from the holder.

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not

1-26

Z 01.2.1/R50-D X

POWER WINDOW

place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

involved in serious accidents.

The power window only operates when the ignition key is in the “ON” position. To open or close the window, push down or pull up the switch and hold it. The main switch (driver side switches) will open or close all the windows. Locking passenger’s window When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.

SIC0599

I Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.

I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls and become trapped in a window. Unattended children could become

1-27

Z 01.2.1/R50-D X

SIC0600

SIC0559

SIC0601

The passenger side switch will open or close only the corresponding window. To open or close the window, hold the switch down or up.

Automatic operation To fully open the driver side window, com- pletely push down the switch and release it; it need not be held. The window will automati- cally open all the way. To stop the window, just pull up the switch toward the “CLOSE” side. A light press on the switch will cause the window to open until the switch is released.

1-28

Z 01.2.1/R50-D X

SUNROOF (If so equipped)

SIC0560

” side.

The sunroof will only operate when the ignition key is in the “ON” position. Sliding the sunroof To open the roof, keep pressing the switch to the “ To close the roof, keep pressing the switch to the “ Tilting the sunroof To tilt up, first close the sunroof, then keep pushing the “

” side of the tilt switch.

” side.

The shade will open automatically when the sunroof is opened. However, it must be closed manually.

I In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints properly.

I Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is closing.

I Remove water drops, snow,

ice or sand from the sunroof before open- ing.

I Do not place any heavy object on the

sunroof or surrounding area.

SIC0561

To tilt down the sunroof, keep pushing the ” side. “ Sun shade Open/close the sun shade by sliding it backward/forward.

1-29

Z 01.2.1/R50-D X

INTERIOR LIGHT

If the sunroof does not close Have your NISSAN dealer check and repair the sunroof.

the interior light will not illuminate, regard- less of door position.

I When the switch is in the center “q” posi- tion, the light will illuminate when a door is opened.

I When the switch is in the “ON” position, the illuminate, whether any

interior light will door is open or closed.

Leaving the interior light switch in the “ON” position for extended periods of time will result in a discharged battery.

SIC0564

The interior light has a three-position switch.

The interior light will operate regardless of ignition key position. I When the switch is in the “OFF” position,

1-30

Z 01.2.1/R50-D X

SPOT LIGHT

VANITY MIRROR LIGHT

SIC0565

SIC0186

The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.

Do not use for extended periods of time with the engine stopped. This could re- sult in a discharged battery.

INTEGRATED HomeLink TRANSMITTER (If so equipped) The Integrated HomeLink Transmitter pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. THE INTEGRATED HomeLink TRANSMITTER: I will operate garage doors, gates, home/ office lighting systems and security sys- tems by storing and transmitting the pro- gramming information of your current hand- held transmitters.

I is built-in and powered by your vehicle’s battery and charging system. No separate batteries are necessary.

Do not use this Integrated HomeLink Transmitter with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards (these standards be- came effective for models manufactured after April 1, 1982). A garage door opener which cannot “detect” an object in the path of a closing garage door and then automatically stop and reverse the door, does not meet current federal

1-31

Z 01.2.1/R50-D X

safety standards. Using a garage door opener without these features increases the risk of serious injury or death.

PROGRAMMING THE HomeLink TRANSMITTER

SIC0602

During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.

Your vehicle’s engine should be turned off while programming your transmitter.

1-32

The Integrated HomeLink Transmitter may not work with older garage door openers that do not meet current Fed- eral Consumer Safety Standards.

1. Test the Integrated HomeLink Transmitter by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3.

2. Clear all channels on the Integrated HomeLink Transmitter by holding down both outside buttons (#1 & #3) until the red light begins to flash rapidly (approximately 20 seconds). Then release both buttons.

3. Select which of

the three Integrated HomeLink Transmitter buttons you want to program.

4. Hold your hand-held transmitter against the bottom surface Integrated HomeLink Transmitter so that you can still see the red indicator light.

the

of

5. Press the desired button until the red indi- cator light flashes slowly. Do not release the button. Continue holding and press the hand-held transmitter button through step 6.

6. Hold down both buttons until the red indi- cator light on the Integrated HomeLink

Z 01.2.1/R50-D X

Transmitter flashes rapidly (This may take 1
to 90 seconds). Then release both buttons. The rapid flashing means that the transmit- ter has been successfully programmed to match your hand-held transmitter. You can now use the Integrated HomeLink Trans- mitter instead of your hand-held transmitter.

to 1992, D.O.C.

Note to Canadian users: Prior regulations required many hand-held transmitters to stop transmit- ting after one or two seconds, even though you continue to hold down the button. If you think you have one of these hand-held transmitters, you should press and re-press the transmitter button every 2 seconds without ever releasing the integrated HomeLink Transmitter button. The Integrated HomeLink Transmitter should blink rapidly indicating a successful programming proce- dure. If it returns to the slow blink of program mode, continue to periodically reactivate your hand-held transmitter until a successful pro- gramming procedure is indicated by the rapidly flashing indicator light.

indicator

light

the

on

OPERATING THE TRANSMITTER To operate, simply press the appropriate but- ton on the Integrated HomeLink Transmitter. The red indicator light illuminates while the signal is being transmitted. The effective trans- mission range of the Integrated HomeLink Transmitter may differ from your hand-held transmitter. PROGRAMMING PROBLEM DIAGNOSIS Be sure to keep your original hand-held trans- mitter for possible reprogramming if neces- sary. I Make sure batteries in the hand-held trans-

mitter are fully charged.

I Hold your hand-held transmitter against the bottom surface Integrated HomeLink Transmitter so that you can still see the red indicator light.

the

of

I Hold buttons for duration of the program-

ming without interruption.

I Rotate your hand-held transmitter end- over-end and program again. For best re- sults, place the end opposite the battery compartment Integrated HomeLink Transmitter when program- ming.

against

the

1-33

Z 01.2.1/R50-D X

flashes rapidly for 1 to 2 seconds, then re- mains on, your garage door opener has a rolling code system.

To operate your “Rolling Code” garage door opener from your HomeLink Transmitter, fol- low these steps:

1. Program your hand held transmitter to the HomeLink Transmitter by following the procedures outlined above (if not yet pro- grammed).

2. Program your garage door opener receiver to recognize your HomeLink Transmitter (The HomeLink Transmitter follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed):

a) Remove the cover panel from your ga- rage door opener receiver. The receiver should be located by the garage door opener motor.

b) Locate the training button on the garage door opener receiver. The exact location and color of the button may vary by garage door opener brand. If you have difficulty locating the training button, ref- erence opener manual. If you have difficulty program- ming your garage door opener equipped

garage

door

your

with a rolling code system to recognize Transmitter with the the HomeLink “Rolling Code” feature, call NISSAN Consumer Affairs Department.

c) Press the training button on the garage door opener receiver for 1 to 2 seconds.

d) Return to the HomeLink Transmitter in the vehicle, and depress the pro- grammed HomeLink button for the du- ration of the fast blink on the HomeLink Transmitter (1 to 2 seconds). Release the button, and re-press to confirm that the system has trained.

e) Your garage door opener should now recognize your HomeLink Transmitter. You may use either your HomeLink Transmitter or your original hand held transmitter to open your garage door. CLEARING THE PROGRAMMING INFORMATION Should you sell your vehicle, be sure to clear the channels of the Integrated HomeLink Transmitter. To clear the channels, simulta- neously hold down the outside two buttons (#1
& #3) until the red indicator light begins to flash rapidly (approximately 20 seconds). This will clear all three buttons. Individual buttons can- not be cleared, but can be reprogrammed at

1-34

Z 01.2.1/R50-D X

SPA0609

ROLLING CODES (If so equipped) If your hand held transmitter appears to train to the HomeLink Transmitter, but does not open your garage door, and your garage door opener was manufactured after 1995, your garage door opener may have a “Code Pro- tected” or “Rolling Code” feature. This type of system will change the “code” of your garage door opener every time you open or close your garage door. To determine if you have one of these sys- tems, depress the button on the HomeLink Transmitter that you have just programmed. If the LED on the HomeLink Transmitter

approved by the party responsible for com- pliance could void the user’s authority to operate the device. DOC: ISTC 1763K1313
FCC I.D.: CB2V67690

any time by following the programming proce- dures described above. IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was Integrated HomeLink Transmitter as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those de- vices.

programmed

into

the

When your vehicle is recovered, you will have to reprogram the Integrated HomeLink Transmitter with your new transmitter information. FCC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly

1-35

Z 01.2.1/R50-D X

MEMO

1-36

Z 01.2.1/R50-D X

2 Pre-driving checks and adjustments

......................................................................... 2-2
Key .............................................................. 2-2
Door locks ......... 2-4
Multi-remote control system (If so equipped) ................................................ 2-6
Battery replacement .................................................... 2-7
Spare tire carrier Back door locks ....................................................... 2-8
Rear window locks .................................................. 2-8
Hood release .......................................................... 2-9
..................................................... 2-10
Glove box lock Fuel filler lid lock .................................................. 2-10
....................................................... 2-11
Fuel filler cap Front seats ........................................................... 2-12
Rear seats ............................................................ 2-16
Supplemental restraint system (Supplemental air bag system)

............................ 2-19

Warning labels ...................................................... 2-25
Supplemental air bag warning light ..................... 2-25
Seat belts ............................................................. 2-27
Child restraints for infants and small children ....................................................... 2-34
Tilting steering wheel ........................................... 2-41
Sunvisors ............................................................... 2-42
Outside mirror control .......................................... 2-42
.................................................... 2-43
Outside mirrors Inside mirror ......................................................... 2-44
Luggage net .......................................................... 2-44
Luggage hooks........................................................ 2-45
Luggage rack ........................................................ 2-46

Z 01.2.1/R50-D X

KEY

DOOR LOCKS

SPA0461

SPA0383

PD1160M

Locking doors with key To lock the door, turn the key towards the front of the vehicle. To unlock, turn it towards the rear.

The key can only be inserted fully in the ignition key cylinder. For the door, back door and glove box key cylinders, it is normal for the key not to go into the key cylinder all the way. Record the key number on the key number plate and keep it in a safe place (such as your wallet), NOT IN THE CAR. A key number plate is supplied with your key. Keep the plate in a safe place. NISSAN does not record key num- bers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer or a lock smith shop.

Locking doors without key To lock from the outside without a key, move the inside lock knob to the “LOCK” position. Then close the door.

When locking the door this way, be certain not to leave the key inside the vehicle.

I Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to

2-2

Z 01.2.1/R50-D X

prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.

I Before opening any door, always look

for and avoid oncoming traffic.

I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.

IC1156M

SPA0384

CHILD SAFETY REAR DOOR LOCK Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, the rear door can be opened only from the outside.

POWER DOOR LOCK The power door lock system allows you to lock or unlock all doors simultaneously. Operating the lock-unlock switch will unlock all doors including the back door.

lock or

I Before opening any door, always look

for and avoid oncoming traffic.

I Do not leave children unattended in- side the vehicle. They may unknow- ingly activate switches or controls.

2-3

Z 01.2.1/R50-D X

Unattended children could become involved in serious accidents.

Locking doors 1. Remove the ignition key. 2. Close all the doors. 3. Push the “ controller.

” button on the multi-remote

4. All the doors will lock. 5. The hazard indicator flashes twice. I When the “

” button is pushed with all doors locked, the hazard indicator flashes twice as a reminder that the doors are already locked.

MULTI-REMOTE CONTROL SYSTEM (If so equipped) It is possible to lock/unlock all doors including the back door. Be sure to remove the key from the vehicle before locking the doors and leaving it. The remote controller can operate at a dis- tance of approximately 49 ft (15 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact your NISSAN dealer.

Listed below are conditions or occur- rences which will damage the remote controller. I Do not allow the remote controller to

become wet.

I Do not drop the remote controller. I Do not strike the remote controller

sharply against another object.

I Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).

2-4

Z 01.2.1/R50-D X

The interior light can be turned off without waiting for 30 seconds by inserting the key into the ignition or by locking the doors with the multi-remote controller or by pushing the inte- rior light button. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the alarm to call atten- tion as follows:

1. Push the “

” button on the remote

controller for longer than 1.5 seconds.

Unlocking doors 1. Push the “

” button on the multi-

troller again within 5 seconds.

3. All doors will unlock.

remote controller.

2. Only the driver side door will unlock. Push ” button on the multi-remote con-

the “

4. The interior light will stay on for 30 seconds when the interior light switch is in the center “q” position.

2-5

SPA0398

2. The theft warning alarm and headlights will

stay on for 30 seconds.

” or the “

3. The alarm will stop when any of the key functions are used. For example, when the “ ” button is pushed, or the “ ” button is pushed for longer than 1.5 seconds on the multi-remote controller, the panic alarm function will be cancelled.

The remote controller will not function. I When the key is inserted into the key

switch.

I When the battery in the remote control-

ler is dead.

I The distance between the remote con-

Z 01.2.1/R50-D X

BATTERY REPLACEMENT

troller and vehicle is more than approx. 49 ft (15 m).

I When one of the doors is ajar, only the

unlock function can be operated.

Replace the two batteries as follows:

1. Remove the screw and open the lid.

2. Replace the batteries with new ones. Insert

the batteries as illustrated above.

Recommended batteries: Sanyo CR2016
or equivalent.

3. Close the lid securely and install the screw.

4. Press the “

” button two or three times to check the multi-remote controller operation.

then the “

” button,

SPA0399

other than replacement, perform step 4
above. I An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal.

I The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry.

I When changing batteries, do not let dust

or oil get on the controller.

If the batteries are removed for any reason

2-6

Z 01.2.1/R50-D X

SPARE TIRE CARRIER

FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference and (2) this de- vice must accept any interference received, including interference that may cause un- desired operation of the device.

SPA0385

SPA0386

When opening the back door, first open the spare tire carrier in the sequence shown in the illustration above. Then insert the stopper into the hole to secure the carrier in the open position.

I Before driving, be certain that the spare tire carrier is firmly closed and latched.

I Failure to do so may injure pedestri-

ans or damage the vehicle.

I Be certain that there is adequate area

to allow the carrier to open fully.

I Open and close the spare tire carrier

slowly.

2-7

Z 01.2.1/R50-D X

BACK DOOR LOCKS

REAR WINDOW LOCKS

This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section.

SPA0462

1. Turn the key counterclockwise to unlock the

back door.

2. Pull the opener handle to open the back

door.

3. To lock the back door, push it down firmly

and turn the key clockwise.

I Always check the back door has been closed securely to prevent it from opening while driving.

I Do not drive with the back door open.

SPA0338

To open the rear window, turn the key fully clockwise and pull the opener handle. To close, lower and push the rear window down securely.

Do not drive with the rear window open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driv- ing” section.

2-8

Z 01.2.1/R50-D X

HOOD RELEASE

Do not open the rear window unless the wiper is in the stowed position.

1. Pull the hood lock release handle located below the instrument panel; the hood will then spring up slightly.

2. Raise the lever at the front of the hood with

your fingertips and raise the hood.

3. Insert the assist bar into the slot in the front

edge of the hood.

4. When closing the hood, reset the assist bar to its original position, then slowly close the hood and make sure it locks into place.

SPA0387

I Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. I If you see steam or smoke coming

2-9

Z 01.2.1/R50-D X

GLOVE BOX LOCK

FUEL FILLER LID LOCK

from the engine compartment, avoid injury, do not open the hood.

to

The glove box may be opened by turning the key as shown.

SPA0388

Keep glove box lid closed while driving to prevent injury in an accident or during a sudden stop.

SPA0389

Opener lever To open the fuel filler lid, push the opener lever down. To lock, close the fuel filler lid securely.

2-10

Z 01.2.1/R50-D X

FUEL FILLER CAP

SPA0341

The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard.

I Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seri- ously injured if it is misused or mis- handled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refuel- ing.

I Fuel may be under pressure. Turn the cap one-half turn and wait for any “hissing” sound to stop, to prevent fuel from spraying out and possible personal injury. Then remove the cap. I Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper opera- tion of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury.

If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

If the fuel filler cap is not tightened prop- erly, the Malfunction indicator light (MIL) may come on.

Put the fuel filler cap on the cap holder while refueling.

SPA0342

2-11

Z 01.2.1/R50-D X

FRONT SEATS

SEAT ADJUSTMENT

I Do not adjust the driver’s seat while driving. The seat may move suddenly and could cause loss of control of the vehicle.

I After adjustment, gently rock in the is securely

to make sure it

seat locked.

SPA0472

SPA0473

vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly. See “Precautions on seat belt usage” later in this chapter.

Do not ride in a moving vehicle when the seatback is reclined. This can be dan- gerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive se- rious internal injuries.

For most effective protection when the

2-12

Z 01.2.1/R50-D X

Forward and backward Pull the lever up while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining To recline the seatback, pull the lever up and lean back. To bring the seatback forward again, pull the lever and move your body forward. The seatback will move forward.

SPA0097

SPA0099

Seat lifter (Driver’s seat) Turn either dial to adjust the angle and height of the seat cushion to the desired position.

2-13

Z 01.2.1/R50-D X

Reclining Move the recline switch backward until the desired angle is obtained. To bring the seat back forward again, move the switch forward and move your body forward. The seat back will move forward.

POWER SUPPORT SEAT

I Do not adjust the driver’s seat while driving in order that full attention may be given to the driving operations.

I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches and controls.

SPA0463

Operating tips I The motor has an auto-reset overload pro- tection circuit. the motor stops during operation, wait 30 seconds, then reactivate the switch.

If

I Do not operate the power support seat for a long period of time when the engine is off. This will discharge the battery.

Forward and backward Moving the switch forward or backward will slide the seat forward or backward to the desired position.

2-14

Z 01.2.1/R50-D X

SPA0464

SPA0465

SPA0014

Seat lifter (Driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion.

Lumbar support (Driver’s seat) Turn the lever forward or backward to adjust the seat lumbar area.

HEAD RESTRAINT

Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjust- ment after someone else uses the seat.

Adjust the top of the head restraints level with the top of your ears.

To raise the head restraint, just pull it up. To

2-15

Z 01.2.1/R50-D X

lower, push the lock knob and push the head restraint down.

REAR SEATS

SPA0350

Before folding down the seat, hook the buckle sideways on to the button and hook on the tongue from the top.

2-16

Z 01.2.1/R50-D X

equipped with seats and seat belts. I Be sure everyone in your vehicle is in a seat and using a seat belt properly. I Head restraints should be adjusted properly as they may provide signifi- cant protection against injury in an accident. Always replace and adjust them properly if they have been re- moved for any reason.

I If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident.

Folding 1. Remove the head restraints. 2. Pull the strap forward and fold the seat

cushion up.

3. Pull the lever and pull the seatback forward

to fold it down.

4. When resetting the seat, be sure to install

the head restraints.

IC0371

I Never allow anyone to ride in the luggage area or on the rear seat when it is in the fold-down position.

I It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

I Do not allow people to ride in any is not

area of your vehicle that

2-17

Z 01.2.1/R50-D X

belt and receive serious internal inju- ries.

I For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly. See “Precautions on seat belt usage” later in this chapter. I After adjustment, check to be sure

the seat is securely locked.

SPA0351

Center armrest Pull the armrest forward and lay it horizontal.

2-18

Z 01.2.1/R50-D X

IC0385

Pull the reclining lever and position the seat back at the desired angle. Release the reclin- ing lever after positioning the seat at the desired angle.

I Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap

SUPPLEMENTAL RESTRAINT SYSTEM (SUPPLEMENTAL AIR BAG SYSTEM) This Supplemental Restraint System section contains important information concerning the driver and passenger supplemental air bags. The Supplemental Restraint System Air Bag can help reduce impact force to the driver and to the front passenger in certain frontal colli- sions. The supplemental air bags are designed to supplement the crash protection provided by the driver and passenger seat belts and are not a substitute for them. The seat belts should always be correctly worn and the driver and front passenger seated a suitable distance away from the steering wheel and instrument panel. (See “Seat belts” for instructions and precautions on seat belt usage.) After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

SPA0504

SPA0505

I The supplemental air bags ordinarily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Al- ways wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.

I The seat belts and the supplemental air bags are most effective when you

2-19

force.

are sitting back and upright in the seat. Supplemental air bags inflate with great If you are unre- strained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the supplemental air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practical from the steering

Z 01.2.1/R50-D X

SPA0476

SPA0477

SPA0478

wheel or instrument panel. Always use the seat belts.

I Keep hands on the outside of the steering wheel. Placing them inside the steering wheel rim could increase the risk that they are injured when the supplemental air bag inflates.

2-20

Z 01.2.1/R50-D X

SPA0479

SPA0480

SPA0481

2-21

Z 01.2.1/R50-D X

restraint in the front seat. An inflating supplemental air bag could seriously injury or kill your child. See “Child restraints for infants and small chil- dren” for details.

sf

SPA0482

SPA0483

I Never let children ride unrestrained. Do not attempt to hold them in your lap or arms. Some examples of dan- gerous riding positions are shown in the previous illustrations.

I Children may be severely injured or killed when the supplemental air bag inflates if they are not properly re- strained.

I Also, never install a rear-facing child

2-22

Z 01.2.1/R50-D X

The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dashboard. Since the supplemental air bag inflates quickly in order to help protect the occupant, the force of the supplemental air bag inflating can increase the risk of injury if the occupant is too close to or is against the supplemental air bag module during inflation.

The supplemental air bag will deflate quickly after a collision. After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

I Do not attach any objects to the steering wheel pad and to the instru- ment panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause in- jury if the supplemental air bag in- flates.

the steering wheel;

Supplemental air bag system The driver supplemental air bag is located in the center of the front passenger supplemental air bag is mounted in the dashboard above the glove box. The supplemental air bag system is designed to inflate in higher severity frontal collisions, al- though it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental air bag operation. When the supplemental air bag inflates, a fairly

SPA0390B

loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of breathing trouble should get fresh air promptly.

Supplemental air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the occupant. They can help save lives and reduce serious injuries. However, an inflating supplemental air bag may cause facial abrasions or other injuries. Supplemental air bags do not provide restraint to the lower body.

2-23

Z 01.2.1/R50-D X

I Right after inflation, several supple- mental air bag system components will be hot. Do not touch them; you may severely burn yourself.

I No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or dam- age to the supplemental air bag sys- tem.

I Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the supplemental air bag system.

I Tampering with the supplemental air bag system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the dashboard, or by installing additional trim mate- rial around the supplemental air bag system.

I Work around and on the supplemen- tal air bag system should be done by an authorized NISSAN dealer. Instal- lation of electrical equipment should also be done by an authorized NISSAN dealer. The SRS wiring har- nesses* should not be modified or disconnected. Unauthorized electri- cal test equipment and probing de- vices should not be used on the supplemental air bag system.

* SRS wiring harnesses are covered with yellow insulation either just be- fore the harness connectors or for the complete harness, for easy identifi- cation.

When selling your vehicle, we request that you inform the buyer about the supplemen- tal air bag system and guide the buyer to the appropriate sections in this Owner’s Manual.

2-24

Z 01.2.1/R50-D X

WARNING LABELS

SUPPLEMENTAL AIR BAG WARNING LIGHT

Warning labels about the supplemental air bag system are placed in the vehicle.

SPA0391

SPA0392

The supplemental air bag light, displaying “AIR BAG” in the instrument panel, monitors the circuits of the supplemental air bag. The cir- cuits monitored by the supplemental air bag light are the diagnosis sensor unit, supplemen- tal air bag modules and all related wiring. After turning the ignition key to the “ON” posi- tion, the air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7 seconds if the system is opera- tional.

2-25

Z 01.2.1/R50-D X

NISSAN dealer if there is any damage to the front end portion of the vehicle. I If you need to dispose of a supple- mental air bag or scrap the vehicle, contact an authorized NISSAN dealer. Correct supplemental air bag dis- posal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.

If any of the following conditions occurs, the supplemental air bag needs servicing.

1. The supplemental air bag light goes off

within 7 seconds.

2. The supplemental air bag light flashes in- termittently or remains on (after 7 seconds). 3. The supplemental air bag light does not

come on at all.

Under these conditions, the Supplemental Re- straint System Air Bag may not operate prop- erly. It must be checked and repaired. Take your vehicle to the nearest authorized NISSAN dealer.

the supplemental air bag system ment of should be done only by authorized NISSAN dealers. To ensure long-term functioning, the sys- tem must be inspected 10 years after the date of manufacture noted on the certifica- tion label located on the driver side center pillar.

When maintenance work is required on the vehicle, the supplemental air bag system and related parts should be pointed out to the person conducting the maintenance. The igni- tion key should always be in the “LOCK” position when working under the hood or in- side the vehicle.

If the supplemental air bag warning light is on, it could mean that the supplemen- tal air bag will not operate in an accident.

Repair and replacement procedure The supplemental air bag system is designed to inflate on a one-time-only basis. As a re- minder, unless it is damaged, the supplemen- tal air bag light will remain illuminated after inflation has occurred. Repair and replace-

I Once the supplemental air bag has the supplemental air bag inflated, module will not function again and must be replaced. The supplemental air bag module should be replaced by an authorized NISSAN dealer. The supplemental air bag module cannot be repaired.

I The supplemental air bag system should be inspected by an authorized

2-26

Z 01.2.1/R50-D X

SEAT BELTS

SPA0506

SPA0485

SPA0486

PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted. NISSAN strongly encourages you and all of your pas- sengers to buckle up every time you drive, even if your seating position includes a supple- mental air bag. Some states, provinces or territories re- quire that seat belts be worn at all times when a vehicle is being driven.

2-27

Z 01.2.1/R50-D X

I Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained and, in a child restraint.

if appropriate,

I The belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.

I Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder.

I Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal

injuries in an accident.

I Be sure the seat belt tongue is se- curely fastened to the proper buckle. I Do not wear the belt inside out or twisted. Doing so may reduce its ef- fectiveness.

I Do not allow more than one person to

use the same belt.

I Never carry more people in the ve-

hicle than there are seat belts.

I If the seat belt warning lamp glows continuously while the ignition is turned “ON” with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by your NISSAN dealer.

I All seat belt assemblies including re- tractors and attaching hardware should be inspected by your NISSAN dealer after any collision. NISSAN recommends that all seat belt assem- blies in use during a collision be replaced unless the collision was mi- nor and the belts show no damage

2-28

and continue to operate properly. Seat belt assemblies not in use dur- ing a collision should also be in- spected and replaced if either dam- age or improper operation is noted.

CHILD SAFETY Children need adults to help protect them.

Infants and children need special pro- tection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints.

All U.S. states and provinces of Canada re- quire the use of approved child restraints for infants and small children. (See “Child re- straints for infants and small children” later in this section.)

In addition,

there are many types of child

Z 01.2.1/R50-D X

restraints available for larger children which should be used for maximum protection. Infant or small child NISSAN recommends that infants or small children be placed in child restraints that com- ply with Federal Motor Vehicle Safety Stan- dards or Canadian Motor Vehicle Safety Stan- dards. You should choose a child restraint that fits your vehicle and always follow the manu- facturer’s instructions for installation and use. Children Children who are too large for child restraints should be seated and restrained by the seat belts which are provided.

NISSAN recommends that children sit in the rear seat if possible. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the

the shoulder belt

vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.

Injured persons NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recommendations.

Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident.

Pregnant women NISSAN recommends that pregnant women use seat belts. Contact your doctor for specific recommendations. The lap belt should be worn snug and positioned as low as possible around the hips, not the waist.

2-29

Z 01.2.1/R50-D X

Do not ride in a moving vehicle when the seatback is reclined. This can be dan- gerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive se- rious internal injuries.

For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.

2. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps.

3-POINT TYPE WITH RETRACTOR

SPA0492A

Every person who drives or rides in this vehicle should wear a seat belt at all times.

Fastening the belts 1. Adjust the seat.

PD1024M

The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion will permit the belt to move, and allow you some freedom of movement in the seat. 3. Position the lap belt portion low on the

hips as shown.

4. Pull the shoulder belt portion toward the

retractor to take up extra slack.

The front seat passenger side seat belt and rear 3-point seat belts have a cinching mecha- nism for child seat installation. It is referred to as the automatic locking mode.

2-30

Z 01.2.1/R50-D X

When the cinching mechanism is activated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted. Refer to “Child Restraint Systems for Infants and Small Children” later in this section for more information. The automatic locking mode should be used only for child seat installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. Unfastening the belts To unfasten the belt, press the button on the buckle. The seat belt will automatically retract. Checking seat belt operation Your seat belt retractors are designed to lock belt movement by two separate methods:

1) When the belt is pulled quickly from the

retractor.

2) When the vehicle slows down rapidly.

You can check the operation as follows: I Grasp the shoulder belt and pull quickly forward. The retractor should lock and re- strict further belt movement.

If the retractor does not lock during this check or if you have any question about belt opera- tion, see your NISSAN dealer.

PD1328MA

Shoulder belt height adjustment The shoulder belt anchor height should be adjusted to the position best suited for you (see “Precautions on Seat Belt Usage”). To adjust, squeeze the release buttons, then move it to the desired position so that the belt passes over the shoulder.

I After adjustment, release the button and check that it does not move up and down to make sure the shoulder

2-31

Z 01.2.1/R50-D X

belt anchor is securely fixed in posi- tion.

I The shoulder belt anchor height

should be adjusted to snug fit. Failure to do so may reduce the effec- tiveness of the entire restraint system and increase the chance or severity of injury in an accident.

SPA0531

SPA0110

Belt hook When the rear seat belt is not in use, hook it at the belt hook.

2-POINT TYPE WITHOUT RETRACTOR (Center position of rear seat) Selecting correct set of belts The center seat belt buckle and tongue are identified by the “CENTER” mark. The center seat belt tongue can be fastened only into the center seat belt buckle.

2-32

Z 01.2.1/R50-D X

SPA0107

SPA0108

SPA0109

Fastening the belts 1. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps.

If the retractor locks and restricts further move- ment, let the belt rewind into the retractor, then slowly pull the belt out.

2. Position the lap belt low and snug on the

hips as shown.

3. Pull the belt toward the retractor to take up

extra slack.

Unfastening the belts To unfasten the belt, press the button on the buckle.

2-33

Z 01.2.1/R50-D X

SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The extender adds approximately 8 inches (200
mm) of length and may be used for either the driver or right passenger seating position. See your NISSAN dealer for assistance if the ex- tender is required.

I Only NISSAN belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN belts.

I Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.

SEAT BELT MAINTENANCE I To clean the seat belt webbings, apply a mild soap solution or any solution recom- mended for cleaning upholstery or carpets. Then brush the webbing, wipe it with a cloth and allow it to dry in the shade. Do not allow the seat belts to retract until they are com- pletely dry.

I If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.

I Periodically check to see that the seat belt and the metal components such as buckles, tongues, retractors, flexible wires and anchors work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire belt assembly should be replaced.

CHILD RESTRAINTS FOR INFANTS AND SMALL CHILDREN

I Infants and small children should al- ways be placed in an appropriate child restraint while riding in the ve- hicle. Failure to use a child restraint can result in serious injury or death. I Children and infants should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.

I Nissan recommends that the child restraint be installed in the rear seat. According to accident statistics, chil- dren are safer when properly re- strained in the rear seat than in the front seat.

I An improperly installed child re- straint could lead to serious injury or death in an accident.

2-34

Z 01.2.1/R50-D X

In general, child restraints are designed to be installed with a lap belt or the lap portion of a three point type seat belt. Child restraints specially designed for infants and small chil- dren are offered by several manufacturers. When selecting any child restraint, keep the following points in mind: 1) Choose only a restraint with a label certify- ing that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.

2) Check that child restraint in your vehicle to be sure it is compatible with the vehicle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recom- mended practice J1819 for child restraint installation.

3) If the child restraint is compatible with your vehicle, place your child in the child re- straint and check the various adjustments to be sure the child restraint is compatible with your child. Always follow all recom- mended procedures.

All U.S. states and provinces of Canada require that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper- ated.

I Never install a rear-facing child re- straint in the front seat. An inflating supplemental air bag could seriously injure or kill your child. A rear-facing child restraint must only be used in the rear seat. See “Installation on front passenger seat” for details.

I Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.

I Follow all of the child restraint manu- facturer’s instructions for installation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.

I If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.

I Adjustable seatbacks should be posi-

2-35

tioned to fit the child restraint, but as upright as possible.

I After attaching a child restraint, test the restraint before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds it in place. If the re- straint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.

I For a front facing child restraint, if the seat position where it is installed has a 3-point type lap/shoulder belt, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint.

I When your child restraint is not in use, store it in the trunk or keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident.

Z 01.2.1/R50-D X

Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.

instructions for belt routing.