1998 Nissan Frontier Owners Manual

re-checked using the HOT range.

the fluid should be

1. Park the vehicle on a level surface and

set the parking brake.

2. Start the engine and then move the se- lector lever through each gear range, ending in P (Park).

8-10 Do-it-yourself

ADI1033

3. Check the fluid level with the engine

idling.

4. Remove the dipstick and wipe it clean

with lint-free paper.

5. Re-insert the dipstick into the charging

pipe as far as it will go.

6. Remove the dipstick and note the read- ing. If the level is on the low side of either range, add fluid through the charging pipe.

CAUTION

c DO NOT OVERFILL. c Use ONLY NISSAN Matic ‘D’ (Conti- nental U.S. and Alaska) or genuine NISSAN Automatic Transmission Fluid (Canada). DexronTM III/MerconTM or equivalent may also be used. Out- side the continental United States and Alaska contact an authorized NISSAN dealership for more information re- garding suitable fluids, including rec- of DexronTM ommended III/MerconTM.

brands

NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the fluid level cannot be read accurately. You should wait until the fluid has cooled down (about 30 min- utes).

Z X

POWER STEERING FLUID

BRAKE AND CLUTCH FLUID

ADI0700

ADI0712

ADI0716

Check the power steering fluid level. The fluid level should be checked using the HOT range on the dipstick at fluid tempera- tures of 122 to 176°F (50 to 80°C) or using the COLD range on the dipstick at fluid temperatures of 32 to 86°F (0 to 30°C).

CAUTION

c Do not overfill. c The recommended fluid is type

DEXRONTMIII or equivalent.

Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add DOT 3
fluid up to the MAX line. Check the clutch fluid level in the reservoir (manual transmission only). If the fluid level is below the MIN line, add DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be thoroughly checked by an autho- rized NISSAN dealer.

Do-it-yourself

8-11

Z X

For further brake and clutch fluid specifica- tion information, refer to ‘‘Capacities and recommended fuel/lubricants’’ in the ‘‘Tech- nical and consumer information’’ section of this manual.

WARNING

Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the brake system and af- fect the vehicle’s stopping ability.

CAUTION

Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, wash with water.

8-12 Do-it-yourself

WINDOW WASHER FLUID

Follow the manufacturer’s instructions for the mixture ratio.

CAUTION

Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint.

ADI1034

USA Only Check the window washer fluid level in the reservoir tank and add fluid if necessary. Add a washer solvent to the water for better cleaning. In the winter season, add a wind- shield washer anti-freeze. Follow the manu- facturer’s instructions for the mixture ratio. Canada Only Add fluid when the low washer fluid warning light comes on. Add a washer solvent to the water for better cleaning. In the winter sea- son, add a windshield washer anti-freeze.

Z X

JUMP STARTING If jump starting is necessary, see ‘‘Jump starting’’ in the ‘‘In case of emergency’’ section. If the engine does not start by jump starting, the battery may have to be re- placed. Contact an authorized NISSAN dealer.

BATTERY

c Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water.

c Make certain the terminal connections

are clean and securely tightened.

c If the vehicle is not to be used for 30 days or longer, disconnect the negative (−) bat- tery terminal cable to prevent discharge.

WARNING

c Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by battery action is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention.

c When working on or near a battery, always wear suitable eye protection and remove all jewelry.

c Keep the battery out of the reach of

children.

ADI0709

1. Gently pry between the battery cap and

cover as illustrated to remove the cap. Use a cloth to protect the battery case.

2. Check the fluid level in each cell.

If it is necessary to add fluid, add only distilled water to bring the level up to the level indicator in each filler opening. Do not overfill.

Do-it-yourself

8-13

Z X

DRIVE BELTS

ADI0710

ADI0730

WARNING

Be sure the ignition key is OFF. The engine could rotate unexpectedly.

1. Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by an autho- rized NISSAN dealer.

2. Have the belts checked regularly for con- dition and tension in accordance with the maintenance schedule found in the ‘‘Maintenance’’ section of this manual.

Z X

8-14 Do-it-yourself

SPARK PLUG REPLACEMENT

Tightening torque:

14 to 22 ft-lb (20 to 29 Nzm)

5. Reconnect the spark plug cables to their

original positions.

DI1229M

DI0065

WARNING

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to remove the plugs. An incorrect socket can cause damage.

1. Disconnect spark plug cables. Keep

track of the original cable locations.

When disconnecting, always hold the boots — not the cables. Mark all cables to identify their original location. 2. Remove spark plugs with a spark plug

socket.

3. Check each new spark plug gap with a

feeler gauge. Correct it as required.

4. Install spark plugs. When installing a plug, turn it two or three turns by hand and then tighten with a spark plug socket. Be careful not to overtighten it.

Do-it-yourself

8-15

Z X

the engine backfires. If it isn’t there and the engine backfires, you could be burned. Don’t drive with it off, and be careful working on the engine with the air cleaner off.

c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

AIR CLEANER HOUSING FILTER

ADI0720

The filter element should not be cleaned and reused as it is given a special treat- ment. We recommend it be replaced ac- cording to the maintenance intervals shown in the ‘‘Maintenance’’ section of this manual. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.

WARNING

c Operating the engine with the air cleaner off can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if

8-16 Do-it-yourself

Z X

WIPER BLADES

CAUTION

c After wiper blade replacement, return the wiper arm to its original position. Otherwise it may be damaged when the engine hood is opened.

c Make sure the wiper blade contacts the glass. Otherwise, the arm may be damaged from wind pressure.

If your windshield is not clear after using the windshield washer or if a wiper blade chat- ters when running, wax or another material may be on the blade or windshield.

Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter- gent. Then rinse the blade with clear water. If your windshield is still not clear after cleaning the blades and using the wiper, replace the blades. Type A replacement 1. Lift the wiper arm away from the wind-

shield.

ADI1043

2. Push the release tab,

then move the wiper blade down the wiper arm to re- move.

3. Remove the wiper blade. 4. Insert the new wiper blade onto the wiper

arm until it clicks into place.

Do-it-yourself

8-17

Z X

Type B replacement 1. Lift the wiper arm away from the wind-

shield.

2. Push the release tab,

then move the wiper blade down the wiper arm to re- move.

3. Remove the wiper blade. 4. Insert the new wiper blade onto the wiper

arm until it clicks into place.

8-18 Do-it-yourself

ADI1044

Z X

PARKING BRAKE CHECK

BRAKE PEDAL

ADI1035

DI0453

Pull the parking brake lever up. If the num- ber of clicks is out of the range listed above, see an authorized NISSAN dealer.

MDI0005

If you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may cause clogging or im- proper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin.

With the engine running, check distance A between the upper surface of the pedal and the metal floor. Distance A:

Manual Transmission

Automatic Transmission

4 1/8 in. (105mm)

4 1/2 in. (115mm)

4 in. (100mm)

2WD Rear Wheel ABS

4WD Four Wheel ABS

If it is out of the range shown above, see an authorized NISSAN dealer.

Do-it-yourself

8-19

Z X

checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occasional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is nor- mal and does not affect the function or performance of the brake system. The rear drum brakes (if so equipped) do not have audible wear indicators. Should you ever hear an unusually loud noise from the rear drum brakes, have them inspected as soon as possible by an authorized NIS- SAN dealer. Proper brake inspection intervals should be followed. For more information regard- ing brake inspections, see the appropriate maintenance schedule information in the ‘‘Maintenance Schedule’’ section of this manual.

Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front disc-type brakes self-adjust every time the brake pedal is applied. The rear drum-type brakes on two-wheel drive trucks self-adjust every time the parking brake is applied. The rear drum-type brakes on four- wheel drive trucks self-adjust every time the brake pedal is applied. If the brake pedal goes down farther than normal, it may be due to a lack of adjustment of the rear drum brakes. Apply the parking brake several times.

WARNING

If the brake pedal height does not re- turn to normal, see an authorized NIS- SAN dealer and have it checked.

Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires replacement, it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes 8-20 Do-it-yourself

BRAKE BOOSTER

Check the brake booster function with the following steps: 1. With the engine off, press and release times. When the brake pedal several brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to next step.

2. While depressing the brake pedal, start the engine. The pedal height should drop a little.

3. With the brake pedal depressed, stop the engine. Keeping the pedal depressed for about 30 seconds, the pedal height should not change.

4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will de- crease gradually with each depression as the vacuum is released from the booster.

If the brakes do not operate properly, have the brakes checked by an authorized NIS- SAN dealer.

Z X

CLUTCH PEDAL

ADI0528

Press the pedal by hand and be sure the free travel is within the above limit. If free travel is out of the range shown above, see an authorized NISSAN dealer.

Do-it-yourself

8-21

Z X

FUSES

Passenger compartment

CAUTION

Never use a fuse of higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire.

If the electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition key and the headlight

switch are OFF.

2. Remove the fuse box cover.

8-22 Do-it-yourself

3. Remove the fuse with the fuse puller. 4. If the fuse is open, replace it with a new

fuse.

5. If a new fuse opens again, have the electrical system checked and repaired by an authorized NISSAN dealer.

ADI1036

Z X

LIGHT BULBS

HEADLIGHTS

CAUTION

CAUTION

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c When handling the bulb, do not

touch the glass envelope.

Replacing the headlight bulb 1. Open the engine hood. 2. Disconnect

the negative (2) battery

cable.

3. Disconnect the electrical connector from

the rear end of the bulb.

4. Push down the spring retainer. 5. Remove the headlight bulb. Do not shake

or rotate the bulb when removing it.

ADI1037

6. Install the new bulb in the reverse order

of removal.

The headlight is a semi-sealed beam type which uses a replaceable headlight (halo- gen) bulb.

c Be sure the lip of the rubber cap

contacts the headlight body.

DO NOT TOUCH THE BULB.

c Use the same number and wattage

as originally installed: Wattage 65/45
Bulb No. HB1

c Aiming is not necessary after replac-

ing the bulb.

c Do not leave the bulb out of the headlight reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the head- light.

c When aiming adjustment is neces- sary, contact an authorized NISSAN dealer.

Do-it-yourself

8-23

Z X

BULB REPLACEMENT

Item

Wattage (W)

Bulb No.

Front combination light:

Turn signal light

Parking light

Rear combination light:

Turn signal

Stop/Tail

Back-up

Rear side marker light

License plate light type A

License plate light type B

Dome light

Dome and cargo light

Map light

High-mounted stop light

8-24 Do-it-yourself

27

3.8

27

27/8

27

3.4

3.8

10

10

2.3

1156

194

3157

3157

3156

158

168

217

—

—

—

2723

MDI0006

Replacing procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.

Z X

ADI1050

Do-it-yourself

8-25

Z X

WHEELS AND TIRES

DI0047

If you have a flat tire, see the ‘‘In case of emergency’’ section of this manual. Maximum inflation pressure Do not exceed the maximum inflation pres- sures shown on the side wall of the tire. Tire inflation pressure Periodically check the tire pressure (includ- ing the spare). Tire pressure should be checked when tires are COLD. COLD tire pressures are shown on the tire placard affixed to the inside of the glove box lid. Incorrect tire pressure may adversely 8-26 Do-it-yourself

affect tire life and vehicle handling. COLD pressure:

After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km).

WARNING

c Improperly inflated tires can fail sud-

denly and cause an accident

c The vehicle weight capacity is indi- cated on the tire placard. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire fail- ure, or unfavorable handling charac- teristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components. c Before taking a long trip, or when- ever you have loaded your vehicle heavily, use a tire pressure gauge to ensure that the tire pressure is at the specified level.

c Do not drive your vehicle over 85
MPH (137 km/h) unless it is equipped

with high capability tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury.

Types of tires

WARNING

When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. An authorized NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maxi- mum speed rating of the tire.

All season tires NISSAN specifies All Season tires on some models to provide good performance for use all year around, including snowy and icy road conditions. All Season Tires are iden- tified by ‘‘ALL SEASON’’ and/or ‘‘M&S’’ on the tire sidewall. Snow tires have better

Z X

snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance in snow and ice will be substantially reduced. Summer tires do not have the tire traction rating ‘‘M&S’’ on the tire sidewall. If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of ‘‘SNOW’’ or ‘‘ALL SEASON’’ tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. If you do not, it can adversely affect the safety and han- dling of your vehicle. Generally, snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. For additional traction on icy roads, studded tires may be used. However, some U.S.

States and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.

Four-wheel drive model

If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels.

CAUTION

ONLY use spare tires specified for each four-wheel drive model.

Tire chains Use of tire chains may be prohibited accord- ing to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s sug- gestions. Use only SAE class ‘‘S’’ chains. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be

secured or removed to prevent the possibil- ity of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Oth- erwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. Never install tire chains on a TEMPORARY USE ONLY spare tire. Tire chains must be installed only on the rear wheels and not on the front wheels. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. When driv- ing on clear paved roads, be sure to change to 2WD.

Do-it-yourself

8-27

Z X

WARNING

c After rotating the tires, adjust the tire

pressure.

c Retighten the wheel nuts after the wheels have been run for the first 600 miles (1,000 km) (also in cases of a flat tire, etc.).

c Do not

include the TEMPORARY USE ONLY spare tire in the tire rota- tion.

ADI0656

Tire rotation NISSAN recommends rotating the tires ev- ery 7,500 miles (12,000 km) for 2WD ve- hicles and every 3,750 miles (6,000 km) for 4WD vehicles. See ‘‘Flat tire’’ in the ‘‘In case of emergency’’ section for tire replacing procedures.

Wheel nut tightening torque:

87 to 108 ft-lb (118 to 147 Nzm)

8-28 Do-it-yourself

MDI0004

Tire wear and damage

WARNING

c Tires should be periodically in- spected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire should be replaced. c The original

tires have a built-in tread wear indicator. When the wear indicator is visible, the tire should be replaced.

Z X

c Improper service for a TEMPORARY USE ONLY spare tire may result in serious personal injury. If it is nec- essary to repair the TEMPORARY USE ONLY spare tire, contact an authorized NISSAN dealer.

Changing tires and wheels When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recom- mended types and sizes are shown in ‘‘Wheel/tire size’’ in the ‘‘Technical and con- sumer information’’ section of this manual.

WARNING

c The use of tires other than those recommended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tire clearance, snow chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury.

c If the wheels are changed for any reason, always replace with wheels which have the same offset dimen- sion. Wheels of a different offset could cause early tire wear, poor ve- hicle handling characteristics and/or interference with the brake discs/ drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear.

c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warn- ing.

c The use of retread tires is not recom-

mended.

FOUR-WHEEL DRIVE MODELS

CAUTION

Always use tires of the same size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires

on the front and rear axles which will cause excessive tire wear and may damage the transmission, transfer case and differential gears.

If excessive tire wear is found, it is recom- mended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact an authorized NISSAN dealer.

CAUTION

ONLY use spare tires specified for each four-wheel drive model.

Wheel balance Unbalanced wheels may affect vehicle han- dling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. Wheel balance service should be performed with the wheels off the vehicle. Spin balanc- ing the front wheels on the vehicle could lead to transmission damage.

Do-it-yourself

8-29

Z X

Care of wheels c Wash the wheels when washing the ve-

hicle to maintain their appearance.

c Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed.

c Do not use abrasive cleaners when

washing the wheels.

c Inspect wheel rims regularly for dents or corrosion. This may cause loss of pres- sure or damage the tire bead.

c NISSAN recommends waxing the road in

wheels to protect against road salt areas where it is used during winter.

Spare tire Your vehicle may be equipped with a TEM- PORARY USE ONLY spare tire. To avoid property damage or personal injury when using the TEMPORARY USE ONLY spare tire, observe the following cautions:

WARNING

c The spare tire should be used for emergency use only. It should be replaced by the standard tire at the

8-30 Do-it-yourself

first opportunity to avoid possible tire or differential damage.

c Drive carefully while the TEMPO- RARY USE ONLY spare tire is in- stalled. Avoid sharp turns and abrupt braking while driving.

c Periodically check spare tire infla- tion pressure. Always keep the pres- sure of the T135/70D16 spare tire at 60 psi (420 kPa, 4.2 bar). Always keep the pressure of the P235/70R15
spare tire at 26 psi (180 kPa, 1.8 bar). c Do not drive the vehicle at speeds

faster than 50 MPH (80 km/h).

c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the front wheels and the original tire used on the rear wheels (drive wheels). Use tire chains only on the two rear original tires.

c Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the TEMPORARY USE ONLY spare tire as soon as the tread wear indi- cators appear.

c Do not use the TEMPORARY USE

ONLY spare tire on other vehicles.

c Do not use more than one TEMPO- RARY USE ONLY spare tire at the same time.

c Do not tow a trailer when the TEM- PORARY USE ONLY T135/70D16
spare is installed.

CAUTION

The transfer control lever must be in the 2H position to prevent the transfer case and differential gears from being damaged.

c Do not use tire chains on a TEMPO- RARY USE ONLY spare tire. Tire chains will not fit properly on a TEM- PORARY USE ONLY spare tire and may cause damage to the vehicle.

c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it might get caught.

Z X

9 Maintenance

General maintenance.............................................9-2
Outside the vehicle ................................................9-2
Inside the vehicle ...................................................9-3
Under the hood and vehicle...................................9-4

Periodic maintenance schedules ...........................9-5
Schedule one .........................................................9-5
Schedule two..........................................................9-5
Explanation of maintenance items.......................9-10

Z X

Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day- to-day and regular maintenance is essential to maintain your NISSAN’s good mechani- cal condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the specified maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. General maintenance General maintenance includes those items which should be checked during normal day-to-day operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these maintenance procedures regularly as prescribed. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, an authorized NISSAN dealer. 9-2 Maintenance

Periodic maintenance The maintenance items listed under peri- odic maintenance in this section are re- quired to be serviced at regular intervals. However, under severe driving conditions, additional or more frequent maintenance will be required. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an autho- rized NISSAN dealer. NISSAN technicians are well-trained spe- cialists who and are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that an authorized NISSAN dealer’s service department per- forms the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way.

GENERAL MAINTENANCE

During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have an authorized NISSAN dealer do it promptly. In addition, you should notify an authorized NISSAN dealer if you think that repairs are required. When performing any checks or mainte- nance work, closely observe the precau- tions in the ‘‘Do-it-yourself’’ section of this manual. OUTSIDE THE VEHICLE The maintenance items listed here should be performed from time to time, unless otherwise specified. Additional information on the following items with ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Tires* Check the pressure with a gauge periodically when at a service station, in- cluding the spare, and adjust to the speci- fied pressure if necessary. Check carefully for damage, cuts or excessive wear. Wheel nuts* When checking the tires, make

Z X

sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km) for 2WD vehicles and 3,750 miles (6,000 km) for 4WD ve- hicles. Wheel alignment and balance If the ve- hicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Doors and hood Check that all doors and the hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, rollers and links if necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication frequently.

Lights* Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. INSIDE THE VEHICLE The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Additional information on the following items with an ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Steering wheel Check for changes in the steering conditions, such as excessive free- play, hard steering or strange noises.

Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched posi- tions. Seat belts Check that all parts of the seat belt system (e.g., buckles, anchors, adjust- ers and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mat away from the pedal. Clutch pedal* Make sure the pedal oper- ates smoothly and check that it has the proper free travel. Brakes Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when de- pressed fully. Check the brake booster func- Maintenance 9-3

Z X

tion. Be certain to keep the floor mat away from the pedal. Parking brake* Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Automatic transmission Park position mechanism Check that the lock release button on the selector lever operates prop- erly and smoothly. On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes. UNDER THE HOOD AND VEHICLE The maintenance items listed here should be checked periodically (e.g., each time you check the engine oil or refuel). Additional information on the following items with an ‘‘*’’ is found in the ‘‘Do-it- yourself operations’’ section. Windshield washer fluid* Check that there is adequate fluid in the reservoir. Engine coolant level* Check the coolant level when the engine is cold. 9-4 Maintenance

Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, de- formation, rot or loose connections. Brake and clutch fluid levels* Make sure that the brake and clutch fluid level is be- tween the MIN and MAX lines on the reser- voir. Battery* Check the fluid level in each cell. It should be between the MAX and MIN lines. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait a few minutes for the oil to drain back into the oil pan. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Automatic transmission fluid level* Check the level after putting the selector lever in P with the engine idling at operating temperature. Exhaust system Make sure there are no

loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by an autho- rized NISSAN dealer. See the carbon mon- oxide warning in the ‘‘Starting and driving’’ section of this manual. Underbody The underbody is frequently exposed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these sub- stances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the ‘‘Appearance and care’’ section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately.

Z X

during stop-and-go ‘‘rush hour’’ traf- fic.

c Extensive idling and/or low speed driving for long distances, such as police, taxi or door-to-door delivery use.

c Driving in dusty conditions. c Driving on rough, muddy, or salt

spread roads.

c Towing a trailer, using a camper or a

car-top carrier.

SCHEDULE TWO Follow Periodic Maintenance Schedule two if none of the driving conditions shown in Schedule one apply to your driving habits.

PERIODIC MAINTENANCE SCHEDULES

To ensure smooth, trouble-free, safe and economical driving, NISSAN provides two periodic maintenance schedules that may be used, depending upon the conditions in which you usually drive. These schedules contain both distance and time intervals, up to 60,000 miles (96,000 km)/48 months. For most people, the odometer reading will in- dicate when service is needed. However, if you drive very little, your vehicle should be serviced at the regular time intervals shown in the schedule. After km)/48
months, continue periodic maintenance at the same mileage/time intervals. SCHEDULE ONE Follow Periodic Maintenance Schedule one if your driving habits frequently include one or more of the following driving conditions: c Repeated short trips of less than 5

60,000 miles

(96,000

miles (8 km).

c Repeated short trips of less than 10
miles (16 km) with outside tempera- tures below freezing.

c Operating the vehicle in hot weather

only)

Maintenance for off-road driving Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be re- quired of the following items: ¶ Brake pads and rotors ¶ Brake linings and drums ¶ Brake lines and hoses ¶ Wheel bearing grease and free-running

hub grease

¶ Differential, transmission and transfer oil ¶ Steering linkage ¶ Propeller shafts and front drive shafts ¶ Air cleaner filter These items should be checked frequently to assure safe and proper operation of your vehicle.

Maintenance 9-5

Z X

Schedule One Abbreviations: R = Replace MAINTENANCE OPERATION

I = Inspect. Correct or replace if necessary.

]: At the mileage intervals only

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Emission control system maintenance Drive belts Air cleaner filter Positive crankcase ventilation (PCV) filter EVAP vapor lines Fuel lines

Fuel filter

Engine coolant Engine oil Engine oil filter Spark plugs

Miles × 1,000 3.75 7.5 11.25 15 18.75 22.526.25 30 33.75 37.541.25 45 48.75 52.556.25 60
(km × 1,000) (96) 48
Months

(12)

(24) 12

(36) 18

(54) 27

(18)

(30) 15

(42) 21

(48) 24

(60) 30

(66) 33

(72) 36

(78) 39

(90) 45

(84) 42

(6)

See NOTE (1) See NOTE (2)

See NOTE (2)* See NOTE (3)

I* [R] [R] I* I*

[R]

I* [R] [R] I* I*

R* [R]

NOTE: (1) If operating mainly in dusty conditions, more frequent maintenance may be required.

(2) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either extremely low or

extremely high, the filters might become clogged. In such an event, replace them immediately.

(3) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. * Maintenance items and intervals with an ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

9-6 Maintenance

Z X

Schedule One Abbreviations: R = Replace

MAINTENANCE OPERATION

I = Inspect. Correct or replace if necessary.

]: At the mileage intervals only

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Miles × 1,000

3.75

7.5 11.25

15

18.75 22.5 26.25

30

33.75 37.5 41.25

45

48.75 52.5 56.25

60

(km × 1,000)

Months

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

(54)

(60)

(66)

(72)

(78)

(84)

(90)

(96)

12

15

18

21

24

27

30

33

36

39

42

45

48

Chassis and body maintenance

Brake lines & cables

Brake pads, rotors, drums & linings

Automatic transmission, transfer & differ- ential gear oil

Manual transmission oil

See NOTE (1)

See NOTE (1)

Steering gear (box) & linkage, axle & suspension parts

Drive shaft boots & propeller shaft (

Front wheel bearing grease (4x2)

Front wheel bearing grease & free-running hub grease (

See NOTE (2)

Exhaust system

Air bag system

See NOTE (3)

NOTE: (1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) oil at every 30,000

miles (48,000 km) or 24 months.

(2) If operating frequently in water, replace grease every 3,750 miles (6,000 km) or 3 months. (3) Inspect the supplemental air bag system 10 years after the date of manufacture noted on the FMVSS certification label.

Maintenance 9-7

Z X

Schedule Two Abbreviations: R = Replace

MAINTENANCE OPERATION

I = Inspect. Correct or replace if necessary.

]: At the mileage intervals only

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Miles × 1,000
(km × 1,000) Months

7.5
(12)

15
(24) 12

22.5
(36) 18

30
(48) 24

37.5
(60) 30

45
(72) 36

52.5
(84) 42

60
(96) 48

See NOTE (1)

Emission control system maintenance Drive belts Air cleaner filter Positive crankcase ventilation (PCV) filter EVAP vapor lines Fuel lines Fuel filter Engine coolant Engine oil Engine oil filter Spark plugs NOTE: (1) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either extremely low

See NOTE (1)* See NOTE (2)

I* [R] [R] I* I*

I* [R] [R] I* I*

R* [R]

[R]

or extremely high, the filters might become clogged. In such an event, replace them immediately. (2) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. * Maintenance items and intervals with an ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

9-8 Maintenance

Z X

Schedule Two Abbreviations: R = Replace

MAINTENANCE OPERATION

I = Inspect. Correct or replace if necessary.

]: At the mileage intervals only

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Miles × 1,000
(km × 1,000) Months

7.5
(12)

15
(24) 12

22.5
(36) 18

30
(48) 24

37.5
(60) 30

45
(72) 36

52.5
(84) 42

60
(96) 48

Chassis and body maintenance Brake lines & cables Brake pads, rotors, drums & linings Automatic transmission, transfer & differential gear oil Manual transmission oil Steering gear (box) & linkage, axle & suspension parts Drive shaft boots ( Front wheel bearing grease (4x2) Front wheel bearing grease & free-running hub grease ( Exhaust system Supplemental air bag system

See NOTE (1)

NOTE: (1) Inspect the supplemental air bag system 10 years after the date of manufacture noted on the FMVSS certification label.

Maintenance 9-9

Z X

EXPLANATION OF MAINTENANCE ITEMS Additional information on the following items with an ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Emission control system maintenance Drive belts* Check drive belts for wear, fraying or cracking and also for proper ten- sion. Replace any damaged drive belts. Air cleaner filter Under normal driving con- ditions, the air cleaner filter should be re- placed in accordance with the maintenance schedule. However, driving the vehicle in dusty areas may cause rapid clogging of the element. Consequently, the element may have to be replaced more frequently. Positive crankcase ventilation (PCV) fil- ter Under normal driving conditions, the filter should be replaced in accordance with the maintenance schedule. If the vehicle is operated under extremely adverse weather conditions or in areas where ambient tem- peratures are either extremely low or ex- tremely high, the filter may become clogged

9-10 Maintenance

If

more rapidly. In such an event, replace the filter immediately. EVAP Vapor lines Check vapor lines and connections for leaks, looseness, or dete- rioration. leaks are found, replace the lines. Fuel lines (hoses, piping, connections, etc.) Check the fuel hoses, piping and con- nections for leaks, looseness or deteriora- tion. Replace any damaged parts. Fuel filter If the vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are ei- ther extremely low or extremely high, the filter might become clogged. In such an event, replace the filter immediately. Engine coolant* Flush and refill the cooling system. Engine oil and oil filter* Under normal driving conditions, the engine oil and oil filter should be replaced in accordance with the maintenance schedule. However, under se- vere driving conditions, they may have to be replaced more frequently. Spark plugs* Replace with new plugs hav- ing the correct heat range.

Chassis and body maintenance Brake lines and cables Check the brake lines and hoses (including brake booster vacuum hoses, connections & check valve) and parking brake cables for proper attach- ment, leaks, cracks, chafing, abrasion, de- terioration, etc. Brake pads, discs, drums and linings Check these and the other brake compo- nents for wear, deterioration and leaks. Un- der severe driving conditions, they may have to be inspected more frequently. Manual and automatic transmission, transfer and differential gear oil Visually inspect for signs of leakage. Under severe driving conditions, the oil should be re- placed at the specified interval. Steering gear (box) and linkage, axle and suspension parts and drive shaft boots Check for damage, looseness and leakage of oil or grease. Under severe driving con- ditions, they may have to be inspected more frequently.

Z X

only).

Propeller shaft(s) Check the propeller shaft(s) for damage, looseness and grease leakage under severe driving conditions Front wheel bearing grease and free- running hub grease Check the wheel bearing for grease leakage around grease seals, axial end play and smooth turning. Repack these in accordance with the main- tenance schedule (4x2). Check the wheel bearing and free running hub for grease leakage around grease seals, axial end play and smooth turning. Repack these in accordance with the main- tenance schedule. In case of frequent driv- ing in muddy water, the bearing grease and free-running hub grease inspection should be performed more frequently ( Exhaust system Visually check the ex- haust pipes, muffler, and hangers for proper attachment, leaks, cracks, chafing, abra- sion, deterioration, etc. Under severe driv- ing conditions, inspection should be per- formed more frequently. Supplemental air bag system Check the supplemental air bag system components for proper attachment, damage, deformities,

).

cracks, rust, etc. Work around and on the supplemental air bag system should be done by an authorized NISSAN dealer.

Maintenance 9-11

Z X

MEMO

9-12 Maintenance

Z X

10 Technical and consumer information

Capacities and recommended fuel/lubricants......10-2
Fuel recommendation...........................................10-4
Engine oil and oil filter recommendation..............10-6
Recommended SAE viscosity number.................10-7
Air conditioner system refrigerant and lubricant recommendations ..................................10-8
Engine ..................................................................10-9
Wheel/tire size....................................................10-10
Dimensions and weights ....................................10-11
Registering your vehicle in another country ......10-12
Vehicle identification ..........................................10-12
Vehicle identification number (VIN) plate...........10-12
Vehicle identification number (chassis number) ..............................................................10-12
Engine serial number .........................................10-13
FMVSS certification label...................................10-13

Emission control information label .....................10-13
Tire placard ........................................................10-14
Air conditioner specification label.......................10-14
Installing license plate........................................10-15
Vehicle loading information................................10-15
Securing the load ...............................................10-16
Truck-camper loading.........................................10-17
Trailer towing......................................................10-19
Towing load/specification chart..........................10-21
Uniform tire quality grading................................10-24
Emission control system warranty .....................10-25
Reporting safety defects (USA) .........................10-25
Readiness for inspection/maintenance (I/M) test......................................................................10-26

Z X

CAPACITIES AND RECOMMENDED FUEL/ LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the ‘‘Do-it-yourself’’ section to determine the proper refill capacity.

Fuel

Engine oil (Refill)

4x2

4x4

With oil filter Without oil filter With oil filter Without oil filter

Cooling system (with heater and reservoir tank)

4x2 M/T 4x2 A/T 4x4

Capacity (Approximate)

US

measure

Imp

measure

15-7/8 gal

13-1/4 gal

3-3/4 qt 3-1/2 qt 4-1/8 qt 3-7/8 qt

9-5/8 qt 9-1/2 qt 9-3/4 qt

3-1/8 qt 2-7/8 qt 3-3/8 qt 3-1/8 qt

8 qt 7-7/8 qt 8-1/8 qt

Liter

60

3.5
3.3
3.9
3.7

9.15
8.95
9.25

Recommended Fluids & Lubricants

Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1

API SG or SH and Energy Conserving II *2
API Certification Mark *2

Anti-freeze coolant (Ethylene glycol base)

*1: For further details, see ‘‘Fuel recommendation’’. *2: For further details, see ‘‘Recommended SAE engine oil viscosity’’.

10-2 Technical and consumer information

Z X

Manual transmission gear oil

Manual steering gear oil

4x2
4x4

4x2 M/T