Login- Download PDF Manual
-
(2.4 GHz). Using the Bluetooth® and the wireless LAN functions at the same time may
4-52 Center display, heater, air conditioner, audio and phone systems
slow down or disconnect the communica- tion and cause undesired noise. is recommended that you turn off the wireless LAN (Wi-Fi) when using the Bluetooth® functions.
It
. Set up the wireless connection between a compatible cellular phone and the in-vehicle phone module before using the Bluetooth® Hands-Free Phone System.
. Some Bluetooth® enabled cellular phones may not be recognized by the in-vehicle phone module. Please visit www.nissanusa. com/bluetooth for a recommended phone list and instructions for connecting your phone.
. You will not be able to use a hands-free
phone under the following conditions: — Your vehicle is outside of the telephone
service area.
— Your vehicle is in an area where it is difficult to receive radio waves; such as in a tunnel, in an underground parking garage, near a tall building or in a mountainous area.
— Your cellular phone is locked to prevent it
from being dialed.
. When the radio wave condition is not ideal it may be to hear the other person’s voice
or ambient sound is too loud, difficult
during a call. Immediately after pushed to the ON position, impossible to receive a call period of time.
the ignition switch is it may be for a short
. Do not place the cellular phone in an area surrounded by metal or far away from the in- vehicle phone module to prevent tone quality degradation and wireless connection dis- ruption.
. While a cellular phone is connected through the Bluetooth® wireless connection, the the cellular phone may battery power of discharge quicker than usual. The Blue- tooth® Hands-Free Phone System cannot charge cellular phones. If the Bluetooth® Hands-Free Phone System seems to be malfunctioning, see “Trouble- shooting guide” later in this section. You can also visit www.nissanusa.com/bluetooth for troubleshooting help.
. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the device in a different location may reduce or eliminate the noise.
. Refer to the cellular phone Owner’s Manual regarding battery charging, cellular phone antenna, etc.
This wireless hands-free car kit is based on Bluetooth technology.
Frequency: 2402 MHz - 2480 MHz Output power: 4.14 dBm E.I.R.P Modulation: FHSS GFSK 8DPSK, p/4DQPSK Number of channels: 79
This wireless equipment cannot be used for any services related to life safety because there is the possibility of radio interference. REGULATORY INFORMATION Bluetooth trademark:Bluetooth® is a trademark owned by Bluetooth SIG, Inc., and licensed to Visteon Cor- poration.
FCC Regulatory information . CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regula- tions.
. Operation is subject to the following two
1. 2.
conditions: this device may not cause interference and this device must accept any interference, including interference that may cause un- desired operation of the device
Center display, heater, air conditioner, audio and phone systems 4-53
IC Regulatory information . Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations.
USING THE SYSTEM The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth® Hands- Free Phone System. If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.
Initialization When the ignition switch is pushed to the ON position, NISSAN Voice Recognition is initia- lized, which takes a few seconds. button is pushed before the initialization com- pletes, the system will not accept any command.
If the
Operating tips To get the best performance out of the NISSAN Voice Recognition system, observe the follow- ing: . Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly. . Wait until the tone sounds before speaking a command. Otherwise, the command will not be received properly.
. Start speaking a command within 5 seconds
after the tone sounds.
. Speak in a natural voice without pausing
between words.
Giving voice command To operate NISSAN Voice Recognition, push and release the button located on the steering wheel. After the tone sounds, speak a command. The command given is picked up by the microphone, and voice feedback is given when the command is accepted.
If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them.
4-54 Center display, heater, air conditioner, audio and phone systems
If a command is not recognized, the system announces, “Command not recognized. Please say again.” Repeat the command in a clear voice. If you want to go back to the previous command, you can say “Go back” or “Correction” anytime the system is waiting for a response.
. You can cancel a command when the system is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. You can also push and hold the button for 5
seconds on the steering wheel at any time to cancel the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system. If you want to adjust the volume of the voice feedback, push the volume control switch (+ or −) on the steering wheel while being provided with feedback. You can also use the radio volume control knob. In most cases you can interrupt the voice feedback to speak the next command by pressing the button on the steering wheel. To use the system faster, you may speak the second level commands with the main menucommand on the main menu. For example, press the button and after the tone say, “Call Redial.” Note: The combined com- mand of Call and (a Name) cannot be used.
How to say numbers NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the rules and examples below. . Either “zero” or “oh” can be used for “0”.
Example: 1-800-662-6200
— “One eight oh oh six six two six two ohoh”, or
— “One eight zero zero six six two six two
oh oh”
. Words can be used for the first 4 digits
places only. Example: 1-800-662-6200
— “One eight hundred six six two six two ohoh”,
— NOT “One eight hundred six six two sixty
two hundred, and
— NOT “One eight oh oh six six two sixty
two hundred.
. Numbers can be spoken in small groups. The system will prompt you to continuing entering digits, if desired. Example: 1-800-662-6200
— “One eight zero zero”
The system repeats the numbers and prompts you to enter more.
— “six six two”
The system repeats the numbers and prompts you to enter more.
— “six two zero zero”
. You can say “Star” for “*” and “Pound” for “#” at any time in any position of the phone number. (Available only when using the “Special Number” command.) Example: 1-555-1212 *123
— “One five five five one two one two starone two three”
. Say “pound” for “#”. Say “star” for “*” (available when using the “Special Number” command and the “Send” command during a call).
. Say “plus” for “+” (available only when using
the “Special Number” command).
. Say “pause” for a 2 second pause (available
only when storing a phone book number). See “Making a call by entering a phone number” (P.4-57) and “List of voice com- mands” (P.4-58) for more information.
NOTE:
For best results, say phone numbers as single digits.
The voice command “Help” is available at any time. Please say the “Help” command to get information about how to use the system. INFO
If you are controlling the telephone system by voice command for the first time or do not know the appropriate voice command, speak “Help”. The system announces the available commands.
. When you speak numbers, you can speak
both “zero” or “oh” for “0”.
Manual command selection Commands can be selected manually. While the commands are displayed on the audio screen, select a command by operating the audio tuning switch, and then push the switch. Once a command is manually selected, the voice command function is cancelled. To return to voice command mode, push the switch to cancel the current operation, and then perform the first procedure of voice command.
Center display, heater, air conditioner, audio and phone systems 4-55
GETTING STARTED The following procedures will help you get started using the Bluetooth® Hands-Free Phone System with NISSAN Voice Recognition. For additional command options, refer to “List of voice commands” (P.4-58).
Choosing a language You can interact with the Bluetooth® Hands- Free Phone System using English, Spanish or French. . Models with navigation system
For information on selecting a different language, see “How to use the setup button” (P.4-5)..
. Models without navigation system
To change the language, perform the following. 1) Press and hold the
button for more
than 5 seconds.
2) The system announces: “Press the PHONE SEND ( the hands-free phone system to enter the speaker adaptation mode or press the PHONE END ( ) button to select a different language.”
) button for
3) Push the For information on speaker adaptation, see “Speaker Adaptation (SA) mode” (P.4-61).
button.
4) The system announces the current language and gives you the option to change the language to Spanish (in Spanish) or French (in French). Use the following chart to select the lan- guage.
NOTE: You must push the
button or the button within 5 seconds to change
the language.
Current lan-
guage
Push (TALK/ PHONE SEND)
to select
English Spanish French
Spanish English English
Push (MODE/
PHONE END)
to select French French Spanish
5)
If you decide not to change the lan- guage, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed.
Connecting procedure NOTE:
The connecting procedure must be per- formed when the vehicle is stationary. If the vehicle starts moving during the pro- cedure, the procedure will be cancelled.
SAA2351
CONTROL BUTTONS The control buttons for the Bluetooth® Hands- Free Phone System are located on the steering wheel.
PHONE SEND
button to initiate a VR session or
Push the answer an incoming call. You can also use the button to interrupt system feedback and give a command at once.
PHONE END
While the voice recognition system is active, press the button to go back one step. Press and hold the button for 5 seconds to quit the voice recognition system at any time.
4-56 Center display, heater, air conditioner, audio and phone systems
1. Push the
button on the steering wheel. The system announces the available com- mands.
2. Say: “Connect Phone” *A . The system acknowledges the command and an- nounces the next set of available commands. 3. Say: “Add phone” *B . The system acknowl- edges the command and asks you to initiate pairing from the phone handset *C . The connecting procedure of the cellular phone varies according to each cellular phone. See the cellular phone Owner’s Manual for details. You can also visit www. nissanusa.com/bluetooth for instructions on connecting NISSAN recommended cellular phones. When prompted for a Passkey code, enter “1234” from the handset. The Passkey code “1234” has been assigned by NISSAN and cannot be changed.
4. The system asks you to say a name for the
phone *D .
If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if more than one phone is connected and the name sounds too much like a name already used, then prompts you for a name again.
the system tells you,
Making a call by entering a phone number
phone number, try entering the number in the following groups: 3-digit area code, 3- digit prefix and the last 4-digits. For example, 555-121-3354 can be said as “five five five” as the 1st group, then “one two one” as the 2nd group, and “three three five four” as the 3rd group. For dialing more than 10 digits or any special characters, say “Special Num- ber”. See “How to say numbers” (P.4-55), for more information.
5. When you have finished speaking the phone the system repeats it back and
number, announces the available commands.
6. Say: “Dial” *C . The system acknowledges
the command and makes the call.
For additional command options, see “List of voice commands” (P.4-58).
Receiving a call When you hear the ring tone, press the button on the steering wheel. Once the call has ended, press the on the steering wheel. NOTE:
button
If you do not wish to take the call when you hear the ring tone, press the button on the steering wheel to reject the call.
1. Push the
button on steering wheel. A
tone will sound.
2. Say: “Call” *A . The system acknowledges the command and announces the next set of available commands.
3. Say: “Phone Number” *B . The system acknowledges the command and an- nounces the next set of available commands. Say: “Special Number” to dial more than 10
digits or any special characters.4. Say the number you wish to call starting with the area code in single digit format. If the system has trouble recognizing the correct
Center display, heater, air conditioner, audio and phone systems 4-57
LIST OF VOICE COMMANDS
the system is waiting for a response.
Call
When you push and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the commands in each sub-menu. Remember to wait for the tone before speaking. You can say “Help” to hear the list of commands currently available anytime the system is waiting for a response. A menu item can also be selected by scrolling the display with the SEEK switch and entering by pushing the If you want to end an action without completing it, you can say “Cancel” or “Quit” at anytime the system is waiting for a response. The system will end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system. If you want to go back to the previous command, you can say “Go back” or “Correction” anytime 4-58 Center display, heater, air conditioner, audio and phone systems
(Speak Name) *A If there are entries stored in the phonebook, a number associated with a name and location can be dialed. See “Phonebook (phones without automatic phonebook download function)” (P.4-59) to learn how to store entries. When prompted by the system, say the name of the phonebook entry to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks the user to choose the location. Once the name and location are confirmed, the system begins the call. “Phone Number” (speak digits) *B When prompted by the system, say the number
button.
to call. Refer to “Making a call by entering a phone number” (P.4-57) for more details. “Redial” *C Use the Redial command to call the last number that was dialed. The system acknowledges the command, re- peats the number and begins dialing. If a redial number does not exist, the system announces, “There is no number to redial” and ends the VR session. “Call back” *D Use the Call Back command to dial the number of the last incoming call within the vehicle. The system acknowledges the command, re- peats the number and begins dialing. If a call back number does not exist, the system announces, “There is no number to call back” and ends the VR session. Special Number To dial more than 10 digits or any special characters, please say “Special Number”. When the system acknowledges the command, the system will prompt you to speak the number. During a call During a call there are several command options available. Push the button on the steering wheel to mute the receiving voice and enter
commands.
“Help” — The system announces the avail- able commands. “Go back/Correction” — The system an- nounces “Go back,” ends the VR session and returns to the call. “Cancel/Quit” — The system announces “Cancel,” ends the VR session and returns to the call. “Send/Enter/Call/Dial” — Use the Send command to enter numbers, “*” or “#” during a call. For example, if you were directed to dial an extension by an auto- mated system: Say: “Send one two three four.” The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR session and returns to the call. Say “star” for “*”, say “pound” for “#”. “Transfer call” — Use the Transfer Call command to transfer from the Bluetooth® Hands-Free Phone System to the cellular phone when privacy is desired. The system announces, “Transfer call. Call transferred to privacy mode.” The system then ends the VR session. To reconnect a call from the cellular phone to the Bluetooth® Hands-Free Phone sys-
the call
button.
tem, push the “Mute” — Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.
NOTE:
If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature will be reset to “off” for the next call so the other party can hear your voice. Phonebook (phones without automatic phonebook download function)
“Transfer Entry” *A Use the Transfer Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry. For example, say: “Mary.” If the name is too long or too short, the system tells you, then prompts you for a name again.
the system tells you,
Also, if the name sounds too much like a name already stored, then prompts you for a name again. The system will ask you to transfer a phone number stored in the cellular phone’s memory. To enter a phone number by voice command: For example, say: “five five five one two one two.” See “How to say numbers” earlier in this section for more information. To transfer a phone number stored in the cellular phone’s memory: Say: “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the Bluetooth® commu- nication link. The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s Manual for details. You can also visit www. nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN re- commended cellular phones. The system repeats the number and prompts you for the next command. When you have finished entering numbers or transferring an entry, choose “Store.” The system confirms the name,
location and
Center display, heater, air conditioner, audio and phone systems 4-59
number. “Delete Entry” *B Use the Delete Entry command to delete one entry from the phonebook. After the system acknowledges a command, say the name to delete or say “List Names” to choose an entry. “List Names” *C Use the List Names command to hear all the names in the phonebook. The system recites the phonebook entries but does not include the actual phone numbers. When playback of the list is complete, the system returns to the main menu. Playback of the list can be stopped at any time by pushing the button on the steering wheel. The system ends the VR session.
Phonebook (phones with automatic phonebook download function) NOTE:
Phonebook commands are not available when the vehicle is moving.
Phone B. “List names” *A Use the List Names command to hear all the names and locations in the phone book. The system recites the phone book entries but does not include the actual phone numbers. When the playback of the list is complete, the system goes back to the main menu. You can stop the playback of the list at any time by pressing the button on the steering wheel. The system ends the VR session. See the “Record Name” command in this section for information about recording custom voice tags for list entries that the system has difficulty pronouncing.
“Record name” *B The system allows you to record custom voice tags for contact names in the phonebook that the vehicle has difficulty recognizing. This feature can also be used to record voice tags to directly dial an entry with multiple numbers. Up to 40 voice tags can be recorded to the system. “Next Name” *C Use the Next Name command to move the next name of list.
For phones that support automatic download of the phonebook (PBAP Bluetooth® profile), the “Phonebook” command is used to manage entries to the vehicle phonebook. You can say the name of an entry at this menu to initiate dialing of that entry. The phonebook stores up to 1000 names for each phone paired with the system. Each name can have up to 4 locations/phone numbers associated with it. When a phone is connected to the system, the phonebook is automatically downloaded to the vehicle. This feature allows you to access your phonebook from the Bluetooth system and call contacts by name. You can record a custom voice tag for contact names that the system has difficulty recognizing. For more information see “Record Name” in this section. NOTE:
Each phone has its own separate phone- book. You cannot access Phone A’s phone- book if you are currently connected with
4-60 Center display, heater, air conditioner, audio and phone systems
“Previous Name” *D Use the Previous Name command to move the previous name of list.
Recent Calls
Connect Phone NOTE:
Add Phone command is not available when the vehicle is moving.
Use the Recent Calls command to access outgoing, incoming or missed calls. “Outgoing” *A Use the Outgoing command to list the outgoing calls made from the vehicle. “Incoming” *B Use the Incoming command to list the incoming calls made from the vehicle. “Missed” *C Use the Missed command to list the missed calls made to the vehicle that were not answered. “Call Back” *D Use the Call Back command to dial the number of the most recently received call.
Use the Connect Phone commands to manage the phones connecting to the vehicle or to enable the Bluetooth® function on the vehicle. “Add Phone” *A Use the Add Phone command to add a phone to the vehicle. See “Connecting procedure” (P.4- 56) for more information. “Select Phone” *B Use the Select Phone command to select from a list of phones connected to the vehicle. The system will list the names assigned to each phone and then prompt you for the phone you wish to select. Only one phone can be active at a time.
“Delete Phone” *C Use the Delete Phone command to delete a phone that is connected to the vehicle. The system will list the names assigned to each phone and then prompt you for the phone you wish to delete. Deleting a phone from the vehicle will also delete that phonebook for that phone. “Bluetooth Off” *D Use the Bluetooth Off command to prevent a wireless connection to your phone. “Replace phone” *E This can be used to reconnect a new phone with the vehicle you have changed your cellular phone. SPEAKER ADAPTATION (SA) MODE Speaker Adaptation allows up to two out-of dialect users to train the system to improve recognition accuracy. By repeating a number of commands, the users can create a voice model of their own voice that is stored in the system. The system is capable of storing a different speaker adaptation model for each connected phone.
Center display, heater, air conditioner, audio and phone systems 4-61
Training procedure 1. Position the vehicle in a reasonably quiet
outdoor location.
10. The system will announce that speaker adaptation has been completed and the system is ready.
2. Sit
in the driver’s seat with the engine the parking brake on, and the
running, transmission in Park.
3. Press and hold the
button for more than
5 seconds.
4. The system announces: “Press the PHONE SEND ( the hands-free phone system to enter the speaker adapta- tion mode or press the PHONE END ( button to select a different language.”
) button for
5. Press the
button.
For information on selecting a different language, see “Choosing a language” (P.4- 56). If the connected phone is already in use, the system will prompt you to overwrite. Follow the instructions provided by the system.
6.
7. When preparation is complete and you are
ready to begin, press the
button.
8. The SA mode will be explained. Follow the
instructions provided by the system.
9. When training is finished, the system will tell you an adequate number of phrases have been recorded.
The SA mode will stop if:
button is pressed for more than 5
The seconds in SA mode. The vehicle is driven during SA mode. The ignition switch is turned to the OFF or LOCK position.
Training phrases During the SA mode, the system instructs you to say the following phrases. (The system will prompt you for each phrase.)
phonebook transfer entry dial 3 0 4 2 9
delete call back number incoming transfer entry 8 pause 9 3 2 pause 7
delete all entries call 7 2 4 0 9
phonebook delete entry next entry dial star 2 1 7 0
yes4-62 Center display, heater, air conditioner, audio and phone systems
no select . missed dial 8 5 6 9 2
. Bluetooth on . Outgoing call 3 1 9 0 2
9 7 pause pause 3 0 8
cancel call back number call star 2 0 9 5
delete phone dial 8 3 0 5 1
. Record name . memo pad delete4 3 pause 2 9 pause 0
delete redial number phonebook list names call 8 0 5 4 1
correction setup main menu dial 7 4 0 1 8delete dial 9 7 2 6 6
call 7 6 3 0 1.
go back call 5 6 2 8 0
dial 6 6 4 3 7Center display, heater, air conditioner, audio and phone systems 4-63
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved.
Symptom
The system fails to interpret the command correctly.
The system consistently selects the wrong entry from the phone book.
Solution 1. Ensure that the command format is valid. (See “List of voice commands” (P.4-58).) 2. Ensure that the command is spoken after the tone. 3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level in the vehicle. 4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster on). NOTE: If it is too noisy to use the phone, it is likely that the voice commands will not be recognized. 5. If more than one command was said at a time, try saying the commands separately. 6. If the system consistently fails to recognize commands, the voice training procedure should be carried out to improve the recognition response for the speaker. (See “Speaker Adaptation (SA) mode” (P.4-61).) 1. Ensure that the phone book entry name requested matches what was originally stored. This can be confirmed by using the “List Names” command. (See “List of voice commands” (P.4-58).) 2. Replace one of the names being confused with a new name.
4-64 Center display, heater, air conditioner, audio and phone systems
5 Starting and driving
Precautions when starting and driving ................................ 5-2
Exhaust gas (carbon monoxide) ...................................... 5-2
Three-way catalyst .............................................................. 5-3
Tire Pressure Monitoring System (TPMS) .................... 5-3
Avoiding collision and rollover ......................................... 5-6
Off-road recovery ................................................................ 5-6
Rapid air pressure loss ...................................................... 5-6
Drinking alcohol/drugs and driving ................................. 5-7Ignition switch (models without Intelligent Key system) ................................................................................ 5-8
Continuously Variable Transmission (CVT) ................... 5-8
Manual Transmission (MT) ................................................ 5-9
Key positions ........................................................................ 5-9Push-button ignition switch (models with Intelligent Key system) ................................................................................ 5-9
Operating range for engine start function ................. 5-10
Push-button ignition switch operation ........................ 5-10
Push-button ignition switch positions ......................... 5-11
Emergency engine shut off ............................................ 5-11
Intelligent Key battery discharge .................................. 5-12
Before starting the engine ................................................... 5-12
Starting the engine ................................................................ 5-13
Models without Intelligent Key system ....................... 5-13
Models with Intelligent Key system ............................. 5-13Driving the vehicle ................................................................. 5-14
Continuously Variable Transmission (CVT) ............. 5-14
Manual Transmission (MT) ........................................... 5-18
Parking brake .......................................................................... 5-20
Cruise control (if so equipped) ......................................... 5-21
Precautions on cruise control ..................................... 5-21
Cruise control operations ............................................ 5-22
Break-in schedule ................................................................. 5-23
Increasing fuel economy ...................................................... 5-23
Parking/parking on hills ........................................................ 5-24
Electric power steering system ......................................... 5-25
Brake system .......................................................................... 5-26
Braking precautions ...................................................... 5-26
Anti-lock Braking System (ABS) ............................... 5-26
Vehicle Dynamic Control (VDC) system ......................... 5-28
Cold weather driving ............................................................ 5-29
Freeing a frozen door lock ........................................... 5-29
Anti-freeze ........................................................................ 5-29
Battery ............................................................................... 5-29
Draining of coolant water ............................................. 5-29
Tire equipment ................................................................ 5-30
Special winter equipment ............................................ 5-30
Driving on snow or ice ................................................. 5-30
Engine block heater (if so equipped) ....................... 5-30PRECAUTIONS WHEN STARTING AND DRIVING
WARNING
. Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent op- eration of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.
5-2 Starting and driving
EXHAUST GAS (carbon monoxide)
WARNING
. Do not breathe exhaust gases; they contain colorless and odorless car- bon monoxide. Carbon monoxide is dangerous. It can cause uncon- sciousness or death.
If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.
. Do not run the engine in closed
spaces such as a garage.
. Do not park the vehicle with the engine running for any extended length of time.
. Keep the back door closed while driving, otherwise exhaust gases could be drawn into the passenger compartment. If you must drive with the back door open, follow these precautions:
1) Open all the windows.
2) Set the
air recirculation to off and the fan control to high to circulate the air.
If electrical wiring or other cable connections must pass to a trailer through the seal on the back door or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.
If a special body, camper or other equipment is added for recreational or other usage, follow the manufac- turer’s recommendation to prevent carbon monoxide entry into the vehicle. (Some recreational vehicle appliances such as stoves, refrig- erators, heaters, etc. may also gen- erate carbon monoxide.)
The exhaust system and body should be inspected by a qualified mechanic whenever:
— The vehicle is raised for service.
— You suspect that exhaust fumes are entering into the passenger compartment.
— You notice a change in the
sound of the exhaust system.
— You have had an accident invol- ving damage to the exhaust system, underbody, or rear of the vehicle.
tion, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine mis- fires, or if noticeable loss of perfor- mance or other unusual operating conditions are detected. Have the vehicle inspected promptly by a NISSAN dealer.
. Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, dama- ging the three-way catalyst.
. Do not race the engine while warm-
ing it up.
. Do not push or tow your vehicle to
start the engine.
THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.
WARNING
The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system com- ponents.
. Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
CAUTION
. Do not use leaded gasoline. Depos- its from leaded gasoline will ser- i o u s l y r e d u c e t h e t h r e e - w a y catalyst’s ability to help reduce ex- haust pollutants.
. Keep your engine tuned up. Mal- functions in the ignition, fuel injec-
TIRE PRESSURE MONITORING SYS- TEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pres- sure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel effi- ciency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger the TPMS low tire
illumination of
that
Starting and driving 5-3
pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approxi- mately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indi- cator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replace- ment or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
Additional information
the tire
The TPMS does not monitor pressure of the spare tire. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a
5-4 Starting and driving
flat tire while driving). The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure. The CHECK TIRE PRES (pressure) warning message is displayed in the vehicle informa- tion display when the low tire pressure warning light is illuminated and low tire pressure is detected. The CHECK TIRE PRES warning message turns off when the low tire pressure warning light turns off. The low tire pressure warning light remains illuminated until the tires are inflated to the recommended COLD tire pressure. The CHECK TIRE PRES warning message is displayed each time the ignition switch is placed in the ON position as long as the low tire pressure warning light remains illumi- nated. (See “Check tire pressure warning message” (P.2-6).) The CHECK TIRE PRES warning message is not displayed if the low tire pressure warning light illuminates to indicate a TPMS malfunction.
Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the outside temperature. Low outside temperature can lower the temperature of the air inside the tire which can cause a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate. If the warning light illuminates in low ambient temperature, check the tire pressure for all four tires.
For additional information, see “Low tire pres- sure warning light” (P.2-14) and “Tire Pressure Monitoring System (TPMS)” (P.6-2).
WARNING
If the low tire pressure warning light illuminates while driving, avoid sud- den steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possi- ble. Driving with under-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pres-
sure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possi- ble. (See “Flat tire” (P.6-2) for chan- ging a flat tire.)
. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.
. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS. . Do not
inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.
CAUTION
FCC Notice:
For USA:
The TPMS may not function properly when the wheels are equipped with tire chains or the wheels are buried in snow.
. Do not place metalized film or any metal parts (antenna, etc.) on the windows. This may cause poor re- ception of the signals from the tire pressure sensors, and the TPMS will not function properly.
Some devices and transmitters may temporarily interfere with the operation of the TPMS and cause the low tire pressure warning light to illuminate. Some examples are:
Facilities or electric devices using similar radio frequencies are near the vehicle. If a transmitter set to similar frequencies is being used in or near the vehicle. If a computer (or similar equipment) or a DC/ AC converter is being used in or near the vehicle.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For Canada:
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.
Starting and driving 5-5
AVOIDING COLLISION AND ROLL- OVER
WARNING
Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.
Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, a loss of control could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Seat belts” (P.1-10) of this manual, and also instruct your passengers to do so. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is
5-6 Starting and driving
significantly more likely to be injured or killed than a person properly wearing a seat belt. OFF-ROAD RECOVERY If the right side or left side wheels leave the road surface, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic. 1. Remain calm and do not overreact. 2. Do not apply the brakes. 3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.
4. When appropriate, slowly release the accel-
5.
erator pedal to gradually slow the vehicle. If there is nothing in the way, steer the vehicle to follow the road while the vehicle speed is reduced. Do not attempt to drive the vehicle back onto the road surface until vehicle speed is reduced.
6. When it is safe to do so, gradually turn the steering wheel until both tires return to the road surface. When all tires are on the road surface, steer the vehicle to stay in the appropriate driving lane.
If you decide that it is not safe to return the vehicle to the road surface based on vehicle, road or traffic conditions, gradu- ally slow the vehicle to a stop in a safe place off the road.
RAPID AIR PRESSURE LOSS Rapid air pressure loss or a “blow-out” can occur if the tire is punctured or is damaged due to hitting a curb or pothole. Rapid air pressure loss can also be caused by driving on under- inflated tires. Rapid air pressure loss can affect the handling and stability of the vehicle, especially at highway speeds. Help prevent rapid air pressure loss by main- taining the correct air pressure and visually inspect the tires for wear and damage. See “Wheels and tires” (P.8-30) of this manual. If a tire rapidly loses air pressure or “blows-out” while driving maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic.
WARNING
The following actions can increase the chance of losing control of the vehicle if there is a sudden loss of tire air pressure. Losing control of the vehicle may cause a collision and result in personal injury.
The vehicle generally moves or pulls in the direction of the flat tire.
. Do not rapidly apply the brakes. . Do not rapidly release the accelera-
tor pedal.
. Do not rapidly turn the steering
wheel.
1. Remain calm and do not overreact. 2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight course.
3. When appropriate, slowly release the accel-
erator pedal to gradually slow the vehicle.
4. Gradually steer the vehicle to a safe location off the road and away from traffic if possible. 5. Lightly apply the brake pedal to gradually
stop the vehicle.
6. Turn on the hazard warning flashers and either contact a roadside emergency service to change the tire or see “Changing a flat tire” (P.6-3) of this Owner’s Manual.
DRINKING ALCOHOL/DRUGS AND DRIVING
is true for drugs,
Remember, drinking and driving don’t mix! And that too (over-the-counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.
WARNING
Never drive under the influence of alcohol or drugs. Alcohol in the blood- stream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the se- verity of the injury.
NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Although the local is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol.
laws vary on what
Starting and driving 5-7
IGNITION SWITCH (models without Intelligent Key system)
WARNING
Never remove or turn the key to the LOCK position while driving. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.
5-8 Starting and driving
When the ignition switch cannot be turned to the LOCK position: 1. Move the selector lever
to the P (Park)
position.
2. Turn the ignition switch slightly in the ON
direction.
3. Turn the ignition switch to the LOCK
position.
4. Remove the key. If the ignition switch is turned to the LOCK position, the selector lever cannot be moved from the P (Park) position. The selector lever can be moved if the ignition switch is in the ON position with the foot brake pedal depressed. There is an OFF position *1
between the LOCK and ACC positions, although it is not marked on the ignition switch.SSD0392
CONTINUOUSLY VARIABLE TRANS- MISSION (CVT) The ignition lock is designed so that the ignition switch cannot be turned to the LOCK position until the selector lever is moved to the P (Park) position. . When turning the ignition switch to the LOCK position, make sure that the selector lever is in the P (Park) position.
. When removing the key from the ignition switch, make sure that the selector lever is in the P (Park) position.
KEY POSITIONS
LOCK (0) The key can only be removed from the ignition switch at this position.
OFF (1) The engine is turned off. The power supply is turned off.
ACC (2) The electrical accessory power activates without the engine turned on.
ON (3) The ignition system and the electrical accessory power activate without the engine turned on.
START (4) The engine starter activates and the engine will start. The ignition switch, when released, will automatically turn to the ON position.
CAUTION
As soon as the engine has started, release the ignition switch immediately.
PUSH-BUTTON IGNITION SWITCH (models with Intelligent Key system)
WARNING
Do not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed 3
consecutive times or the ignition switch is pushed and held for more than 2
seconds.) If the engine stops while the vehicle is being driven, this could lead to a crash and serious injury.Before operating the push-button ignition switch, be sure to move the selector lever to the P (Park) position.
Starting and driving 5-9
SSD0503
removal of
MANUAL TRANSMISSION (MT) The ignition switch includes a device that helps prevent accidental the key while driving. The key can only be removed when the ignition switch is in the LOCK position. To turn the ignition switch to the LOCK position from the ACC or ON position, turn the key to the OFF position, push the key in, then turn the key to the LOCK position. There is an OFF position *1
in between the LOCK and ACC positions. The OFF position is indicated by a “1” on the key cylinder..
the Intelligent Key is placed on the inside the glove box or the Intelligent Key may not
The cargo room area is not included in the operating range but the Intelligent Key may function. If instrument panel, door pocket, function. If the Intelligent Key is placed near the door or window outside the vehicle, the Intelligent Key may function.
SSD0436
OPERATING RANGE FOR ENGINE START FUNCTION The Intelligent Key can only be used for starting the engine when the Intelligent Key is within the specified operating range *1 . When the Intelligent Key battery is almost discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower and may not function properly. If the Intelligent Key is within the operating range, it is possible for anyone, even someone who does not carry the Intelligent Key, to push the ignition switch to start the engine.
5-10 Starting and driving
SSD0859
PUSH-BUTTON IGNITION SWITCH OPERATION When the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change as follows: . Push center once to change to ACC. . Push center two times to change to ON. . Push center three times to change to OFF. . Push center four times to return to ACC. . Open or close any door to return to LOCK The indicator light *A on the ignition switch illuminates when the ignition switch is in the ACC or ON position.
during the OFF position.
EMERGENCY ENGINE SHUT OFF To shut off the engine in an emergency situation while driving, perform the following procedure: . Rapidly push the push-button ignition switch 3 consecutive times in less than 1.5
seconds, or. Push and hold the push-button ignition
switch for more than 2 seconds.
The ignition lock is designed so that the ignition switch position cannot be switched to LOCK until the selector lever is moved to the P (Park) position. When the ignition switch cannot be pushed toward the LOCK position, proceed as follows: 1. Move the selector lever into the P (Park)
position.
2. Push the ignition switch to the OFF position. 3. Open the door. The ignition switch will
change to the LOCK position.
The selector lever can be moved from the P (Park) position if the ignition switch is in the ON position and the brake pedal is depressed. PUSH-BUTTON IGNITION SWITCH POSITIONS
LOCK (Normal parking position) The ignition switch can only be locked in this position. The ignition switch will be unlocked when it is pushed to the ACC position while carrying the Intelligent Key.
ACC (Accessories) This position activates electrical accessories such as the radio, when the engine is not running.
ON (Normal operating position) This position turns on the ignition system and electrical accessories.
OFF The engine can be turned off in this position. The ignition lock is designed so that the ignition switch cannot be switched to the LOCK position until the selector lever is moved to the P (Park) position.
CAUTION
Do not leave the vehicle with the push- button ignition switch in ACC or ON position when the engine is not running for an extended period. This can dis- charge the battery.
Starting and driving 5-11
BEFORE STARTING THE ENGINE
. Make sure the area around the vehicle is
clear.
. Check fluid levels such as engine oil, cool- ant, brake fluid, and window washer fluid as frequently as possible, or at least whenever you refuel.
. Check that all windows and lights are clean. . Visually inspect tires for their appearance and condition. Also check tires for proper inflation. Lock all doors.
. Position seat and adjust head restraints. . Adjust inside and outside mirrors.
Fasten seat belts and ask all passengers to do likewise.
. Check the operation of warning lights when the ignition switch is placed in the ON position. (See “Warning/indicator lights and audible reminders” (P.2-11).)
After step 3 is performed, when the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change to ACC. NOTE: . When the ignition switch is pushed to the ACC or ON position or the engine is started by the above procedures, the Intelligent Key system warning light may blink in yellow even if the Intelli- gent Key is inside the vehicle. This is not a malfunction. To stop the warning light from blinking, touch the ignition switch with the Intelligent Key again. If the Intelligent Key system warning light in the meter is blinking in green, replace the battery as soon as possible. (See “Key battery replacement” (P.8- 23).)
SSD0860
INTELLIGENT KEY BATTERY DIS- CHARGE If the battery of the Intelligent Key is discharged, or environmental conditions interfere with the Intelligent Key operation, start the engine according to the following procedure: 1. Move the selector lever
to the P (Park)
position.
2. Firmly apply the foot brake. 3. Touch the ignition switch with the Intelligent
Key as illustrated. (A chime will sound.)
4. Push the ignition switch while depressing the brake pedal within 10 seconds after the chime sounds. The engine will start.
5-12 Starting and driving
STARTING THE ENGINE
MODELS WITHOUT INTELLIGENT KEY SYSTEM 1. Apply the parking brake. 2. Continuously Variable Transmission
(CVT) models: Move the selector lever to the P (Park) or N (Neutral) position. (P is recommended.) The starter is designed so that it does not operate unless the selector lever is in either of the above positions. Manual Transmission (MT) models:
lever
Move the shift to the N (Neutral) position. Depress the clutch pedal fully to the floor. The starter is designed not to operate unless the clutch pedal is fully depressed.
3. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to START. Release the switch when the engine starts. If the engine starts, but fails to run, repeat the above procedure. the engine is very hard to start
If in extremely cold weather or when restart- ing, depress the accelerator pedal a little (approximately 1/3 to the floor) and hold it and then crank the engine. Release the accelerator pedal when the engine starts.
If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5 - 6 seconds. After cranking the engine, release the accel- erator pedal. Crank the engine with your foot off the accelerator pedal by turning the ignition switch to START. Release the ignition switch when the engine starts. If the engine starts, but fails to run, repeat the above procedure.
CAUTION
Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the ignition switch off and wait 10 seconds before cranking again, otherwise the starter could be damaged.
4. Warm-up
least 30
Allow the engine to idle for at seconds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2 - 3 minutes before shutting it off. Starting andstopping the engine over a short period of time may make the vehicle more difficult to start.
5. To stop the engine, move the selector lever to the P (Park) position (CVT model) or move the shift lever to the N (Neutral) position (MT model), and turn the ignition switch to the OFF position.
MODELS WITH INTELLIGENT KEY SYSTEM 1. Apply the parking brake. 2. Move the selector lever to the P (Park) or N
(Neutral) position. (P is recommended.) The starter is designed not to operate unless the selector lever is in either of the above positions. The Intelligent Key must be carried when operating the ignition switch.
3. Push the ignition switch to the ON position. Depress the brake pedal and push the ignition switch to start the engine. To start the engine immediately, push and release the ignition switch while depressing the brake pedal with the ignition switch in any position.
the engine is very hard to start
If in extremely cold weather or when restart- ing, depress the accelerator pedal a little Starting and driving 5-13
.
(approximately 1/3 to the floor) and while holding, crank the engine. Release the accelerator pedal when the engine starts. If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Push the ignition switch to the ON position to start cranking the engine. After 5 or 6 seconds, stop cranking by pushing the ignition switch to OFF. After cranking the engine, release the accel- erator pedal. Crank the engine with your foot off the accelerator pedal by depressing the brake pedal and pushing the push-button ignition switch to start the engine. If the engine starts, but fails to run, repeat the above procedure.
seconds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2 - 3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start. When racing the engine up to 4,000 rpm or more under no load condition, the engine will enter the fuel cut mode.
5. To stop the engine, move the selector lever to the P (Park) position, and push the ignition switch to the OFF position.
CAUTION
Do not operate the starter for more than 15 seconds at a time. If the engine does not start, push the ignition switch to OFF and wait 10 seconds before cranking again, otherwise the starter could be damaged.
4. Warm-up
Allow the engine to idle for at
least 30
5-14 Starting and driving
DRIVING THE VEHICLE
CONTINUOUSLY VARIABLE TRANS- MISSION (CVT) The Continuously Variable Transmission (CVT) in your vehicle is electronically controlled to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Engine power may be automatically re- duced to protect the CVT if the engine speed increases quickly when driving on slippery roads or while being tested on some dynamometers.
Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before moving the selector lever out of the P (Park) position. This CVT is designed so that the foot brake pedal must be depressed before shifting from P (Park) to any driving position while the ignition switch is in the ON position.
The selector lever cannot be moved out of the P (Park) position and into any of the other positions if the ignition switch is placed in the LOCK, OFF or ACC position or if the key is removed.
2. Keep the foot brake pedal depressed, push lever button and move the
the selector selector lever to a driving position.
3. Release the parking brake and foot brake pedal, and then gradually start the vehicle in motion.
WARNING
. Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive) or L (Low). Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.
. Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.
. Never shift to P (Park) or R (Re- verse) while vehicle is moving. Fail- ure to do so could cause you to lose control and have an accident.
CAUTION
. Except in an emergency, do not shift to the N (Neutral) position while driving. Doing so can cause a loss of engine braking which may result in a collision, serious personal in- jury or death. In addition, coasting with the transmission in the N (Neutral) position may cause ser- ious damage to the transmission.
. When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.
. Do not downshift abruptly on slip- pery roads. This may cause a loss of control.
SSD0862
To move the selector lever,
Push the button *A while depressing the brake pedal. Push the button *A . Just move the selector lever.
Shifting After starting the engine, fully depress the brake pedal, push the selector lever button and move the selector lever from the P (Park) position to any of the desired shift positions.
Starting and driving 5-15
N (Neutral): Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving.
D (Drive): Use this position for all normal forward driving.
L (Low): Use this position for maximum engine braking on steep downhill gradients/climbing steep slopes and whenever approaching sharp bends. Do not use the L (Low) position in any other circum- stances.
WARNING
CAUTION
Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.
If the ignition switch is placed in the OFF or ACC position for any reason while the selector lever is in any positions other than the P (Park), the ignition switch cannot be placed in the LOCK position. If the ignition switch cannot be placed in the LOCK position, perform the following steps: 1. Apply the parking brake when the vehicle is
stopped.
2. Place the ignition switch in the ON position
while depressing the foot brake pedal.
3. Move the selector lever
to the P (Park)
position.
4. Models with Intelligent Key system:
Place the ignition switch in the OFF position. Models without Intelligent Key system: Place the ignition switch in the LOCK position.
5-16 Starting and driving
To prevent transmission damage, move the selector lever to the P (Park) or R (Reverse) position only when the vehi- cle is completely stopped.
P (Park): Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal must be depressed and the selector lever button pushed in to move the selec- tor lever from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the selector lever to the P (Park) position.
R (Reverse): Use this position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed and the selector lever button pushed in to move the selector lever from P (Park), N (Neutral) or any
