2008 Nissan 350z Owners Manual

SDI1752
If a type 쎻A fuse is used to replace a type 쎻B fuse, the type 쎻A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. Type 쎻B fuses cannot be installed in the under- hood fuse boxes. Only use type 쎻A fuses in the underhood fuse boxes.

8-22 Maintenance and do-it-yourself

SDI1479B

SDI1753

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than that specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and headlight

switch are OFF.

2. Open the engine hood and remove the cover on the battery and the fuse/fusible link holder.

3. Remove the fuse/fusible link holder cover by pushing the tabs 쎻1 and lifting the cover 쎻2 . 4. Remove the fuse with the fuse puller. The fuse puller is located in the passenger com- partment fuse box. If the fuse is open 쎻A , replace it with a new fuse 쎻B . Spare fuses are stored in the pas- senger compartment fuse box.

5.

6.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

墌 07.7.25/Z33-D/V5.0 墍

Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts.

SDI1962

2. Open the fuse box lid 쎻1 . 3. Pinch the fuse perpendicularly with the fuse

puller 쎻2 and pull it out.

PASSENGER COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than that specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight

switch are OFF.

Maintenance and do-it-yourself 8-23

墌 07.7.25/Z33-D/V5.0 墍

KEYFOB BATTERY REPLACEMENT

CAUTION

Be careful not to allow children to swal- low the battery and removed parts.

4.

5.

SDI1754
If the fuse is open 쎻A , replace it with a new fuse 쎻B . Spare fuses 쎻3 are stored in the fuse box. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

8-24 Maintenance and do-it-yourself

SDI1608

Replace the battery as follows:

1. Open the lid using a suitable tool. 2. Replace the battery with a new one.

Recommended battery: CR2025 or equivalent

墌 07.7.25/Z33-D/V5.0 墍

approved by the party responsible for com- pliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

Make sure that the ⊕ side faces the bottom case.

쐌 Do not touch the internal circuit and electric terminals as doing so could cause a malfunc- tion.

3. Close the lid securely.

4. Push the keyfob button two or three times to

check its operation.

See a NISSAN dealer if you need any assistance for replacement. If the battery is removed for any reason other than replacement, perform step 4
above. 쐌 Be careful not to touch the circuit board

and the battery terminal.

쐌 An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal.

쐌 The keyfob is water-resistant; however, if it gets wet, immediately wipe it com- pletely dry.

쐌 When changing batteries, do not let

dust or oil get on the keyfob.

FCC Notice: Changes or modifications not expressly

Maintenance and do-it-yourself 8-25

墌 07.7.25/Z33-D/V5.0 墍

LIGHTS

쎻1 Front view 1. Headlight (low-beam, high-beam) 2. Spot light 3. Front park light 4. Front turn signal light 5. Front side marker light 쎻2 Rear view (Coupe), 쎻3 Rear view (Roadster) 6. Luggage compartment light (Coupe) or Trunk

light (Roadster)

7. High-mounted stop light 8. Rear combination light (Side marker, Stop/Tail)

9. License plate lights 10. Rear combination light (Back-up, Turn signal)

8-26 Maintenance and do-it-yourself

SDI2058

墌 07.7.25/Z33-D/V5.0 墍

HEADLIGHTS Replacing If replacement is required, see a NISSAN dealer. Xenon headlight bulb:

WARNING

HIGH VOLTAGE

When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer. For additional information, see “Headlight and turn signal switch” in the “2. Instruments and controls” sec- tion.

CAUTION

Use the same number and wattage as originally installed: Bulb no. (Wattage) D2S (35W) - Xenon low/high-beam

Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer.

Maintenance and do-it-yourself 8-27

墌 07.7.25/Z33-D/V5.0 墍

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Front turn signal light*

Front park light*

Front side marker light*

Rear combination light (Upper)

Stop/Tail*

Side marker*

Rear combination light (Lower)

Back-up*

Turn signal*

License plate light (x 2)

High-mounted stop light*

Spot light

Luggage compartment light (Coupe)

Trunk light (Roadster)*

Vanity mirror light

Cup holder light*

Rear floor box light*

28/8

(LED)

(LED)

(LED)

21

21

(LED)

3.4

1.8

1.1

1.4

Bulb No.

3457NA

T10

—

—

—

T20

T20

T10

—

—

—

—

—

—

—

*: See a NISSAN dealer for replacement. NOTE: Always check with the Parts Department at a NISSAN dealer for the latest information about parts.

8-28 Maintenance and do-it-yourself

MDI0006

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.

墌 07.7.25/Z33-D/V5.0 墍

SDI1779

SDI1572

Interior light (Roadster) Be careful not to snap the nails 쎻A on the plastic cover when removing it.

SDI1450A

Maintenance and do-it-yourself 8-29

SDI1451

墌 07.7.25/Z33-D/V5.0 墍

WHEELS AND TIRES

TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). For more details, refer to “Low tire pressure warning light” in the “2. Instruments and con- trols” section, “Tire pressure monitoring system (TPMS)” in the “5. Starting and driving” section, and “Flat tire” in the “6. In case of emergency” section.

SDI1401A

Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label under the “COLD TIRE PRESSURE” heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: 쐌 Most tires naturally lose air over time. 쐌 Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at mod- erate speeds.

8-30 Maintenance and do-it-yourself

墌 07.7.25/Z33-D/V5.0 墍

Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.

WARNING

쐌 Improperly inflated tires can fail suddenly and cause an acci- dent.

쐌 The Gross Vehicle Weight Rat- ing (GVWR) is located on the F.M.V.S.S./C.M.V.S.S. certifica- tion label. The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle be- yond this capacity. Overloading your vehicle may result in re- duced tire life, unsafe operating conditions due to premature tire failure, or unfavorable han- dling characteristics and could also lead to a serious accident. Loading beyond the specified

capacity may also result in fail- ure of other vehicle compo- nents.

쐌 Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

쐌 Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85
MPH (137 km/h) may result in tire failure, loss of control and possible injury.

쐌 For additional information re- garding tires, refer to “Impor- tant Tire Safety Information” (US) or “Tire Safety Informa- tion” (Canada) in the Warranty Information Booklet.

Maintenance and do-it-yourself 8-31

墌 07.7.25/Z33-D/V5.0 墍

originally installed on the vehicle at the factory.

쎻4 Cold tire pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1
mile (1.6 km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best balance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicle’s GVWR.

쎻5 Tire size — refer to “Tire labeling”

later in this section.

쎻6 Spare tire size or compact spare tire

size (if so equipped).

Tire and Loading Information label 쎻1 Seating capacity: The maximum number of occupants that can be seated in the vehicle.

8-32 Maintenance and do-it-yourself

SDI1948

쎻2 Vehicle load limit: See loading infor- mation in the “Technical and con- sumer information” section.

쎻3 Original size: The size of the tires

墌 07.7.25/Z33-D/V5.0 墍

3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare it to the specifica- tion shown on the Tire and Loading Information label.

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Re- check the pressure and add or release air as needed.

6. Install the valve stem cap. 7. Check the pressure of all other tires,

including the spare.

SDI1949

Checking the tire pressure 1. Remove the valve stem cap from the

tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leak- age.

Coupe model

Front Original Tire Rear Original Tire Spare Tire

Size

Cold Tire Inflation Pressure

225/45R18
245/40R18

240 kPa (35 psi)

245/45R18
265/35R19

T145/80D17

Roadster model

Size

Front Original Tire Rear Original Tire Spare Tire

225/45R18

245/45R18

T145/80D17

240 kPa (35 psi)

420 kPa (60 psi)

Cold Tire Inflation Pressure

240 kPa (35 psi)

240 kPa (35 psi)

420 kPa (60 psi)

Maintenance and do-it-yourself 8-33

墌 07.7.25/Z33-D/V5.0 墍

tire’s ratio of height to width. 4. R: The “R” stands for radial. 5. Two-digit number (15): This number is

the wheel or rim diameter in inches.

6. Two- or three-digit number (95): This number is the tire’s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. Tire Speed Rating. You should not drive the vehicle faster than the tire speed rating.

SDI1575

Example

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

8-34 Maintenance and do-it-yourself

쎻1 Tire size (example: P215/65R15

Example

SDI1951

95H)

1. P: The “P” indicates the tire is de- signed for passenger vehicles. (Not all tires have this information.)

2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to sidewall edge.

3. Two-digit number (65): This number, known as the aspect ratio, gives the

墌 07.7.25/Z33-D/V5.0 墍

4. Three-digit code: Tire type code (Op-

tional)

5. Three-digit code: Date of Manufacture 6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.

쎻3 Tire ply composition and material

The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 쎻4 Maximum permissible inflation pres-

sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.

쎻5 Maximum load rating

This number indicates the maximum

SDI1607

Example

쎻2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX)

1. DOT: Abbreviation for the “Depart- ment of Transportation”. The symbol can be placed above, below or to the left or right of the Tire Identification Number.

2. Two-digit code: Manufacturer’s identi-

fication mark

3. Two-digit code: Tire size

load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

쎻6 Term of “tubeless” or “tube type”

Indicates whether the tire requires an inner tube (“tube type”) or not (“tubeless”).

쎻7 The word “radial”

The word “radial” is shown if the tire has radial structure.

쎻8 Manufacturer or brand name

Manufacturer or brand name is shown.

Other tire-related terminology: In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white letter- ing or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the Maintenance and do-it-yourself 8-35

墌 07.7.25/Z33-D/V5.0 墍

(2)

the tire, or

the other sidewall of outward facing sidewall of an asymmetri- cal tire that has a particular side that must always face outward when mounted on a vehicle. TYPES OF TIRES

WARNING

쐌 When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.

than

rating

쐌 Replacement tires may have a lower factory speed equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.

the

쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the proper operation of the tire

8-36 Maintenance and do-it-yourself

If you do not,

Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you operate your vehicle in snowy or icy conditions, NISSAN recommends the use of snow or all season tires on all four wheels. For additional traction on icy roads, studded tires may be used. However, some provinces and states prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires, on wet or dry surfaces, may be poorer than that of non-studded snow tires.

pressure monitoring system (TPMS). 쐌 For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety In- formation” (Canada) in the Warranty Information Booklet.

All season tires NISSAN specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance in snow and ice will be substantially reduced. Summer tires do not have the tire traction rating M&S on the tire sidewall.

If you operate your vehicle in snowy or icy conditions, NISSAN recommends the use of snow or all season tires on all four wheels.

墌 07.7.25/Z33-D/V5.0 墍

TIRE CHAINS

CAUTION

Tire chains/cables should not be in- stalled on 265/35R19 size tires. Installa- tion of the tire chains/cables on 265/35R19 size tires will cause damage to the vehicle. If you plan to use tire chains/cables, install 245/45R18 size tires on your vehicle.

should

you

Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class “S” chains are designed to meet the SAE standard minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recom-

mended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your ve- hicle may be damaged and/or vehicle handling and performance may be adversely affected. 쐌 Never install the tire chains on a T-type

spare tire.

쐌 Do not use the tire chains on dry roads. 쐌 Tire chains must be installed only on the rear wheels and not on the front wheels.

CHANGING WHEELS AND TIRES Tire rotation Tires cannot be rotated in this vehicle, as front tires are different size from rear tires and the direction of wheel rotation is fixed in each tire. A pin is on the front brake rotor to prevent the rear wheels from being installed in place of the front wheels. The spare tire can be installed in place of the front and rear wheels. When installing the spare tire in the front wheel, the hole in the spare tire wheel must be aligned with the pin on the brake rotor.

WARNING

쐌 Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

쐌 For additional information regarding tires, refer to “Important Tire Safety

Maintenance and do-it-yourself 8-37

墌 07.7.25/Z33-D/V5.0 墍

Information” (US) or “Tire Safety In- formation” (Canada) in the Warranty Information Booklet.

the tire(s) should be replaced. 쐌 The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.

쐌 Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious. Replace the tires as necessary to prevent tire failure and possible personal injury.

쐌 Improper service of the spare tire may result in serious per- sonal injury. If it is necessary to repair the spare tire, contact a NISSAN dealer.

쐌 For additional information re- garding tires, refer to “Impor- tant Tire Safety Information” (US) or “Tire Safety Informa-

SDI1663

1. Wear indicator 2. Wear indicator location mark Tire wear and damage

WARNING

쐌 Tires should be periodically in- spected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found,

8-38 Maintenance and do-it-yourself

墌 07.7.25/Z33-D/V5.0 墍

tion” (Canada) in the Warranty Information Booklet.

Replacing wheels and tires When replacing a tire, use the same size, speed rating and load carrying capacity as originally equipped. See “Specifications” in the “9. Tech- nical and consumer information” section for rec- ommended types and sizes of tires and wheels.

WARNING

쐌 The use of tires other than those recommended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury.

쐌 If the wheels are changed for any

reason, always replace with wheels which have the same off-set dimen- sion. Wheels of a different off-set could cause premature tire wear, possibly degraded vehicle handling characteristics and/or interference with the brake discs/drums. Such in- terference can lead to decreased braking efficiency and/or early brake pad/shoe wear.

쐌 When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the TPMS.

the proper operation of

쐌 Do not install a deformed wheel or tire even if it has been repaired. Such

wheels or tires could have structural damage and could fail without warn- ing.

쐌 The use of retread tire is not recom-

mended.

쐌 For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety In- formation” (Canada) in the Warranty Information Booklet.

Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. Wheel balance service should be performed with the wheels off the vehicle. Spin balancing the front wheels on the vehicle could lead to transmission damage. For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information booklet.

Maintenance and do-it-yourself 8-39

墌 07.7.25/Z33-D/V5.0 墍

since it may get caught.

쐌 Do not use the T-type spare tire on

other vehicles.

쐌 Do not use more than one T-type

spare tire at the same time.

쐌 Do not tow a trailer while the T-type

spare tire is installed.

Care of wheels 쐌 Wash the wheels when washing the vehicle

to maintain their appearance.

쐌 Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

쐌 Do not use abrasive cleaners when washing

the wheels.

쐌 Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

쐌 NISSAN recommends that the road wheels be waxed to protect against road salt in areas where it is used during winter.

Spare tire (T-type spare tire) Observe the following precautions if the T-type spare tire must be used, otherwise your vehicle could be damaged or involved in an accident.

CAUTION

쐌 The T-type spare tire should be used for emergency use only. It should be replaced by the standard tire at the first opportunity.

8-40 Maintenance and do-it-yourself

쐌 Drive carefully while the T-type spare

tire is installed. Avoid sharp turns and abrupt braking while driving.

쐌 Periodically check the T-type spare tire inflation pressure, and always keep it at 60 psi (420 kPa, 4.2 bar).

쐌 Do not drive your vehicle at speeds

faster than 50 MPH (80 km/h).

쐌 Do not use tire chains on a T-type spare tire. Tire chains will not fit properly on the T-type spare tire and may cause damage to the vehicle.

쐌 Tire tread of the T-type spare tire will wear at a faster rate than the stan- dard tire. Replace the T-type spare tire as soon as the tread wear indica- tors appear.

쐌 Because the T-type spare tire is smaller than the original tire, ground clearance is reduced. To avoid dam- age to the vehicle, do not drive over obstacles. Also, do not drive the ve- hicle through an automatic car wash

墌 07.7.25/Z33-D/V5.0 墍

9 Technical and consumer information

Capacities and recommended fuel/lubricants .............. 9-2
Fuel recommendation .................................................... 9-3
Engine oil and oil filter recommendation .................. 9-5
Air conditioner system refrigerant and lubricant recommendations ........................................................... 9-6
Specifications ........................................................................ 9-7
Engine ................................................................................. 9-7
Wheels and tires.............................................................. 9-8
Dimensions and weights ............................................... 9-8

When traveling or registering your vehicle in another country ..................................................................................... 9-9
Vehicle identification ............................................................ 9-9
Vehicle identification number (VIN) plate ................. 9-9
Vehicle identification number (chassis number) ..... 9-9
Engine serial number ................................................... 9-10
F.M.V.S.S./C.M.V.S.S. certification label ................ 9-10
Emission control information label ........................... 9-10
Tire and loading information label ............................ 9-11
Air conditioner specification label ............................ 9-11
Installing front license plate ............................................. 9-12

Vehicle loading information ............................................. 9-13
Terms ............................................................................... 9-13
Vehicle load capacity.................................................... 9-14
Loading tips .................................................................... 9-16
Measurement of weights ............................................. 9-16
Towing a trailer ................................................................... 9-17
Maximum load limits .................................................... 9-17
Towing safety ................................................................ 9-18
Flat towing............................................................................. 9-21
Automatic transmission ................................................ 9-22
Manual transmission ..................................................... 9-22
Uniform tire quality grading ............................................. 9-22
Emission control system warranty ................................. 9-23
Reporting safety defects (US only) ............................... 9-23
Readiness for inspection/maintenance (I/M) test (US only) .............................................................................. 9-24
Event data recorders ......................................................... 9-25
Owner’s Manual/Service Manual order information ... 9-26
In the event of a collision ........................................... 9-26

墌 07.7.25/Z33-D/V5.0 墍

CAPACITIES AND RECOMMENDED FUEL/ LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.

Fuel Engine oil (Drain and refill)*2

With oil filter change Without oil filter change

Cooling system

With reservoir Reservoir

Automatic transmission fluid

Manual transmission gear oil

Differential gear oil

Capacity (Approximate)

US

measure 20 gal

5-1/8 qt 4-7/8 qt

9-1/2 qt 7/8 qt

—

—

—

Imp

measure 16-5/8 gal

4-3/8 qt

4 qt

7-7/8 qt 3/4 qt

—

—

—

Liter

76

4.9
4.6

9.0
0.8
—

—

—

Recommended specifications

Unleaded premium gasoline with an octane rating of at least 91 AKI (RON 96)*1

쐌 Engine oil with API Certification Mark*3
쐌 Viscosity SAE 5W-30

50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Matic J ATF*4
Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi 75W-85 or API GL-4, Viscosity SAE 75W-85 or 75W-90
Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5, Viscosity SAE 80W-90*5
Genuine NISSAN PSF or equivalent*6
Genuine NISSAN Super Heavy Duty Brake Fluid*7 or equivalent DOT 3
NLGI No. 2 (Lithium soap base) HFC-134a (R-134a)*8
NISSAN A/C System Oil Type S or exact equivalent Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-freeze or equivalent

Refill to the proper fluid level according to the instructions in the “8. Maintenance and do-it-yourself” section.

Power steering fluid (PSF) Brake and clutch fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system lubricants Windshield washer fluid *1: For additional information, see “Fuel recommendation” later in this section. *2: For additional information, see “Engine oil” in the “8. Maintenance and do-it-yourself” section for changing engine oil. *3: For additional information, see “Engine oil and oil filter recommendation” later in this section. *4: Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in driveability and automatic transmission

— — — —

— — — —

— — — —

durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty.

*5: For hot areas, viscosity SAE 90 is suitable for ambient temperatures above 32°F (0°C). *6: Canada NISSAN Automatic Transmission Fluid or DEXRONTM VI type ATF may also be used. *7: Available in mainland US through a NISSAN dealer. *8: For additional information, see “Vehicle identification” in this section for air conditioner specification label.

9-2 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

FUEL RECOMMENDATION Use unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96).

If premium gasoline is not available, unleaded regular gasoline with an octane rating of 87 AKI number (Research octane number 91) may be temporarily used, but only under the following precautions: 쐌 Have the fuel tank filled only partially with unleaded regular gasoline, and fill up with unleaded premium gasoline as soon as pos- sible.

쐌 Avoid full throttle driving and abrupt accelera-

tion.

However, for maximum vehicle perfor- mance, the use of unleaded premium gaso- line is recommended.

CAUTION

쐌 Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

쐌 Under no circumstances should a leaded gasoline be used, because this will damage the three-way cata- lyst.

쐌 Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN vehicle limited warranty.

Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter (WWFC) specifi- cations where it is available. Many of the auto- mobile manufacturers developed this specifica- tion to improve emission control system and vehicle performance. Ask your service station manager the gasoline meets the WWFC specifications. Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug-

if

gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and metha- nol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily determined. If in doubt, ask your service station manager. If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. 쐌 The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline.

쐌 If an oxygenate-blend, excepting a methanol blend, is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

쐌 If a methanol blend is used, it should contain no more than 5% methanol (me- thyl alcohol, wood alcohol). It should also contain a suitable amount of ap- propriate cosolvents and corrosion in- Technical and consumer information 9-3

墌 07.7.25/Z33-D/V5.0 墍

NISSAN dealer or other competent service fa- cility. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is no cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

hibitors. If not properly formulated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or ve- hicle performance problems. At this time, sufficient data is not available to ensure that all methanol blends are suitable for use in NISSAN vehicles.

If any undesirable driveability problems such as engine stalling and hard hot starting are experi- enced after using oxygenate-blend fuels, imme- diately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. E-85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 fuel in your vehicle. U.S. govern- ment regulations require fuel ethanol dispensing pumps to be identified by a small, square, or- ange and black label with the common abbre- viation or the appropriate percentage for that region.

9-4 Technical and consumer information

Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel in- jector cleaner, octane booster, intake valve de- posit removers, etc.) which are sold commer- cially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harm- ful to the fuel system and engine. Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy spark knock. (Spark knock is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the above stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have your dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect ignition timing will result in knocking, after-run or overheating. This in turn may cause excessive fuel consumption or damage to the engine. If any of the above symptoms are en- countered, have your vehicle checked at a

墌 07.7.25/Z33-D/V5.0 墍

쎻1 API certification mark 쎻2 API service symbol ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It to choose the correct grade, quality and viscosity engine oil to ensure satis- factory engine life and performance. See “Ca- pacities and recommended fuel/lubricants” ear- lier in this section. NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.

is essential

STI0505

Select only engine oils that meet the American Petroleum Institute (API) certification or Interna- tional Lubricant Standardization and Approval Committee (ILSAC) certification and SAE vis- cosity standard. These oils have the API certifi- cation mark on the front of the container. Oils which do not have the specified quality label should not be used as they could cause engine damage. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important that the engine oil viscosity be selected based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When replacing, use a genuine NISSAN oil filter or its equivalent for the reason described in “Change intervals”. Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Oil and filter other than the specified quality, or oil and filter change intervals longer than recommended could reduce engine life. Damage to engines caused by improper maintenance or use of incorrect oil and filter quality and/or viscosity is not covered by the new NISSAN vehicle limited warranties. Your engine was filled with a high quality engine Technical and consumer information 9-5

墌 07.7.25/Z33-D/V5.0 墍

Contact a NISSAN dealer when servicing your air conditioner system.

oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: 쐌 repeated short distance driving at cold out-

side temperatures

쐌 driving in dusty conditions 쐌 extensive idling 쐌 towing a trailer 쐌 stop and go commuting Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule.

AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the lubricant, NISSAN A/C System Oil Type S or the exact equivalents.

CAUTION

The use of any other refrigerant or lubri- cant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner sys- tem components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle will not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain governmental regulations require the recovery and recycling of any refrigerant during automotive air conditioner system service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant.

9-6 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

SPECIFICATIONS

ENGINE

Type Cylinder arrangement Bore x Stroke Displacement Firing order Idle speed Ignition timing (B.T.D.C.) CO percentage at idle speed Spark plug Spark plug gap (Normal) Camshaft operation

Model

in (mm) cu in (cm3)

rpm degree/rpm [No air] % Standard in (mm)

VQ35HR

Gasoline, 4-cycle 6-cylinder, V-slanted at 60° 3.760 x 3.205 (95.5 x 81.4) 213.45 (3,498) 1-2-3-4-5-6*1

See the emission control label on the underside of the hood.

FXE22HR-11
0.043 (1.1) Timing chain

The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.

*1: Cylinder number

STI0425

Technical and consumer information 9-7

墌 07.7.25/Z33-D/V5.0 墍

WHEELS AND TIRES Road wheel

Model

Type

Position

Size

Offset

in (mm)

Coupe

Aluminum

Roadster

Aluminum

Front Rear Front Rear Front Rear

18 x 8JJ 18 x 8-1/2JJ 18 x 9JJ* 19 x 10JJ* 18 x 8JJ 18 x 8-1/2JJ

1.18 (30) 1.30 (33) 1.18 (30) 1.18 (30) 1.18 (30) 1.30 (33)

DIMENSIONS AND WEIGHTS

Vehicle body

Coupe

Roadster

Overall length

Overall width

Overall height

Front tread

Rear tread

Wheelbase

in (mm)

169.8 (4,314)

169.8 (4,314)

in (mm)

71.5 (1,815)

71.5 (1,815)

in (mm)

52.1 (1,323)

52.5 (1,333)

in (mm)

60.5 (1,536)

60.5 (1,536)

in (mm)

60.6 (1,540)*1
60.9 (1,546)*2

60.6 (1,540)

in (mm)

104.3 (2,650)

104.3 (2,650)

Tire Model

Type

Coupe

Conventional

Road- ster

Spare

Conventional

Spare

*: For option

Position Front Rear Front Rear

—

Front Rear

—

Size Pressure (COLD) 225/45R18 91W 240 kPa (35 psi) 245/45R18 96W 240 kPa (35 psi) 245/40R18 93W* 240 kPa (35 psi) 265/35R19 94W* 240 kPa (35 psi) T145/80D17 107M 420 kPa (60 psi) 225/45R18 91W 240 kPa (35 psi) 245/45R18 96W 240 kPa (35 psi) T145/80D17 107M 420 kPa (60 psi)

Gross vehicle weight rating (GVWR)

lb (kg)

Gross axle weight rating (GAWR)

Front

Rear

lb (kg)

lb (kg)

*1: For model with 245/45R 18 tires *2: For model with 265/35R 19 tires

See the F.M.V.S.S. or C.M.V.S.S. cer- tification label on the driver’s side lock pillar.

9-8 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to travel in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with too low an octane rating may cause engine damage. All gasoline vehicles must be operated with unleaded engine gaso- line. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

VEHICLE IDENTIFICATION

STI0320
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number plate is at- tached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

STI0513
VEHICLE IDENTIFICATION NUMBER (chassis number) The number is stamped as shown.

Technical and consumer information 9-9

墌 07.7.25/Z33-D/V5.0 墍

STI0516

STI0322

STI0514

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.

information label

is at-

F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Standards (F.M.V.S.S.) or Canadian Motor Vehicle Safety Standards (C.M.V.S.S.) certification label is af- fixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.

9-10 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

STI0366
TIRE AND LOADING INFORMATION LABEL The cold tire inflation pressure is shown on the Tire and Loading Information label affixed to the driver side center pillar.

STI0515
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed inside of the hood as shown.

Technical and consumer information 9-11

墌 07.7.25/Z33-D/V5.0 墍

INSTALLING FRONT LICENSE PLATE

Use the following steps to mount the license plate:

Before mounting the license plate, confirm that the following parts are enclosed in the vinyl bag. 쐌 License plate bracket 쐌 J-nut x 2
쐌 Screw x 2
쐌 Screw grommet x 2
1. Temporarily place the license plate bracket while aligning points 쎻A of the front bumper fascia with holes 쎻B in the license plate bracket.

2. Remove the license plate bracket. 3. Carefully drill

two shallow pilot holes 쎻A using a 0.39 in (10 mm) drill bit at the marked locations. (Be sure that the drill only goes through the fascia, or damage to the nut may occur.) Insert grommets into the hole on the fascia. Insert a flat-blade screwdriver into the grom- met hole to add 90° turn onto the part 쎻C . Insert a J-nut into the license plate bracket before placing the license plate bracket on the fascia. Install the license plate bracket with screws.

4. 5.

6.

7.

STI0446

9-12 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

8.

Install the license plate with bolts that are no longer than 0.55 in (14 mm).

WARNING

VEHICLE LOADING INFORMATION

쐌 It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

쐌 Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

쐌 Be sure everyone in your ve- hicle is in a seat and using a seat belt properly.

TERMS It is important to familiarize yourself with the following terms before loading your vehicle: 쐌 Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and optional equipment, flu-

ids, emergency tools, and spare tire assembly. This weight does not in- clude passengers and cargo.

쐌 GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

쐌 GVWR (Gross Vehicle Weight Rat- ing) - maximum total combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. This in- formation the F.M.V.S.S./C.M.V.S.S. label.

located

on

is

쐌 GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle. This informa- tion the F.M.V.S.S./C.M.V.S.S. label.

located

on

is

쐌 GCWR (Gross Combined Weight Rating) - maximum total weight rating of the vehicle, passengers, cargo and trailer.

쐌 Vehicle Capacity Weight, Load limit, Technical and consumer information 9-13

墌 07.7.25/Z33-D/V5.0 墍

load capacity - maximum total Total weight limit specified of the load (pas- sengers and cargo) for the vehicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the vehicle is used to tow a trailer, the trailer tongue weight must be included as part of the cargo load. This information is located on the Tire and Loading Information label.

쐌 Cargo capacity - permissible weight of cargo, the subtracted weight of occu- pants from the load limit.

VEHICLE LOAD CAPACITY Do not exceed the load limit of your vehicle shown as “The combined weight of occupants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Load- ing Information label. To get “the combined weight of occu- pants and cargo”, add the weight of all occupants, then add the total luggage weight. Examples are shown in the fol- lowing illustration.

9-14 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.

4. The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs) or (640 − 340 (5 × 70) = 300 kg)

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and lug- gage load capacity calculated in Step 4.

6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Technical and consumer information 9-15

Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on

STI0447

your vehicle’s placard.

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

墌 07.7.25/Z33-D/V5.0 墍

Before driving a loaded vehicle, confirm that you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See “Measurement of Weights” later in this section. Also check tires for proper inflation pres- sures. See the Tire and Loading Informa- tion label. LOADING TIPS 쐌 The GVW must not exceed GVWR or GAWR the F.M.V.S.S./C.M.V.S.S. certification la- bel.

specified

on

as

쐌 Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.

WARNING

쐌 Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do

9-16 Technical and consumer information

vehicle’s warranty.

MEASUREMENT OF WEIGHTS Secure loose items to prevent weight shifts that could affect the balance of your vehicle. When the vehicle is loaded, drive to a scale and weigh the front and the rear wheels separately to determine axle loads. Individual axle loads should not exceed either of the gross axle weight ratings (GAWR). The total of the axle loads should not exceed the gross ve- hicle weight rating (GVWR). These rat- ings are given on the vehicle certification label. ratings are exceeded, move or remove items to bring all weights below the ratings.

If weight

not place cargo higher than the seatbacks. In a sudden stop or collision, cargo could cause personal injury.

unsecured

and

쐌 Do not load your vehicle any heavier than the GVWR or the maximum front rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of con- trol and cause personal injury. 쐌 Overloading not only could shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and long braking distances. This may cause a premature tire fail- ure, which could result in a se- rious accident and personal in- jury. Failures caused by over loading are not covered by the

墌 07.7.25/Z33-D/V5.0 墍

CAUTION

Vehicle damage resulting from im- proper towing procedures are not cov- ered by NISSAN warranties.

TOWING A TRAILER

Roadster model: Do not tow a trailer with your vehicle.

Coupe model:

Your new vehicle was designed to be used primarily to carry passengers and cargo. Re- member that towing a trailer places additional loads on your vehicle’s engine, drive train, steer- ing, braking and other systems.

A NISSAN Towing Guide (U.S. only) is available on the website at www.nissanusa.com. This guide includes information on trailer towing ca- pability and the special equipment required for proper towing.

WARNING

Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents.

CAUTION

쐌 Do not tow a trailer or haul a heavy load for the first 500 miles (800 km).

Your engine, axle or other parts could be damaged.

쐌 For the first 500 miles (800 km) that you tow a trailer, do not drive over 50
mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of your ve- hicle wear in at the heavier loads.

MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed 1,000
lb (454 kg). The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than 1,000 lb (454 kg) or using improper towing equipment could adversely affect vehicle handling, braking and performance. The ability of a vehicle to tow a trailer is not only related to the maximum trailer loads, but also the places you plan to tow. Tow weights appropriate for level highway driving may have to be reduced on very steep grades or in low traction situations (for example, on slippery boat ramps).

Technical and consumer information 9-17

墌 07.7.25/Z33-D/V5.0 墍

TI1011M

TI1012M

Tongue load Keep the tongue load between 9 and 11% of the total trailer load within the maximum tongue load limits Towing Load/Specification chart. If the tongue load be- comes excessive, rearrange cargo to allow for proper tongue load.

following

shown

the

in

Maximum gross vehicle weight/ maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed. GVWR shown on the F.M.V.S.S./C.M.V.S.S. certification label. The gross vehicle weight equals the combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. front or rear gross axle weight must not exceed GAWR shown on the F.M.V.S.S./C.M.V.S.S. certifica- tion label.

In addition,

TOWING LOAD/SPECIFICATION CHART

Unit: lb (kg)

MAXIMUM TOWING LOAD

MAXIMUM TONGUE LOAD

1,000 (454)

100 (45.4)

to help avoid personal

TOWING SAFETY Trailer hitch Choose a proper hitch for a vehicle and trailer. Make sure the trailer hitch is securely attached to the vehicle, injury or property damage due to sway caused by cross- winds, rough road surfaces or passing trucks. Hitch ball Choose a hitch ball of the proper size and weight rating for your trailer: 쐌 The required hitch ball size is stamped on most trailer couplers. Most hitch balls also have the size printed on top of the ball.

쐌 Choose the proper class hitch ball based on

the trailer weight.

쐌 The diameter of the threaded shank of the hitch ball must be matched to the ball mount hole diameter. The hitch ball shank should be

9-18 Technical and consumer information

墌 07.7.25/Z33-D/V5.0 墍

no more than 1/16″ smaller than the hole in the ball mount.

쐌 The threaded shank of the hitch ball must be long enough to be properly secured to the ball mount. There should be at least 2 threads showing beyond the lock washer and nut.

Class I hitch Class I trailer hitch equipment (receiver, ball mount and hitch ball) can be used to tow trailers of a maximum weight of 2,000 lb (909 kg).

You may add Class I trailer hitch equipment to the vehicle that has a 2,000 lb (909 kg) maxi- mum weight rating, but your vehicle is only capable of towing the maximum trailer weights shown in the Towing Load/Specification Chart earlier in this section.

CAUTION

쐌 Do not use axle-mounted hitches. 쐌 The hitch should not be attached to or affect the operation of the impact- absorbing bumper.

쐌 Do not modify the vehicle exhaust system, brake system, etc. to install a

trailer hitch.

쐌 To reduce the possibility of addi- tional damage if a vehicle is struck from the rear, where practical, re- move the hitch and/or receiver when not in use.

쐌 After the hitch is removed, seal the bolt holes to prevent exhaust fumes, water or dust from entering the pas- senger compartment.

쐌 Regularly check that all trailer hitch mounting bolts are securely mounted.

Tire pressures 쐌 When towing a trailer, inflate the ve- hicle tires to the recommended cold tire pressure indicated on the Tire and Loading Information label.

쐌 Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturers’ specifications.

Safety chains Always use a suitable chain between a vehicle and the trailer. The safety chain should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. Be sure to leave enough slack in the chain to permit turning corners. Trailer lights

CAUTION

commercially

When splicing into the vehicle electrical system, available power-type module/converter must be used to provide power for all trailer lighting. This unit uses the vehicle bat-