manufacturer’s recommendations. Some fabric protectors contain chemicals that may stain or bleach the seat material.
Use a cloth dampened only with water, to clean the meter and gauge lens.
CAUTION
쐌 Never use benzine, thinner or any
similar material.
쐌 Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, pol- ishes, oils, cleaning fluids, solvents, detergents or ammonia-based clean- ers as they may damage the leather
natural finish.
쐌 Never use fabric protectors unless recommended by the manufacturer. 쐌 Do not use glass or plastic cleaner on meter or gauge lens covers. It may damage the lens cover.
FLOOR MATS The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they be- come excessively worn.
SAI0012
Floor mat positioning aid (driver’s side only) This model includes a front floor mat bracket to act as a floor mat positioning aid. NISSAN floor mats have been specially designed for your vehicle model. The driver’s side floor mat has a grommet hole incorporated in it. Simply position the mat by placing the floor mat bracket through the floor mat grommet hole while centering the mat in the floorpan contour. Periodically check to make certain that the mats are properly positioned.
Appearance and care 7-5
墌 07.7.25/Z33-D/V5.0 墍
SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely before using them. See “Seat belt maintenance” in the “1. Safety — Seats, seat belts and supplemental restraint system” section.
WARNING
Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these may severely weaken the seat belt webbing.
CORROSION PROTECTION
MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 쐌 The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.
쐌 Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.
ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate corro- sion. Wet floor coverings will not dry completely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated in areas of high relative humidity, especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used.
Temperature A temperature increase will accelerate the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use will accelerate the corrosion process. Road salt will also accelerate the disintegration of paint sur- faces. TO PROTECT YOUR VEHICLE FROM CORROSION 쐌 Wash and wax your vehicle often to keep the
vehicle clean.
쐌 Always check for minor damage to the paint
and repair it as soon as possible.
쐌 Keep drain holes at the bottom of the doors
open to avoid water accumulation.
쐌 Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible.
7-6 Appearance and care
墌 07.7.25/Z33-D/V5.0 墍
CAUTION
쐌 Never remove dirt, sand or other de- bris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.
쐌 Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them.
Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, the underbody must be cleaned periodically. For additional protection against rust and corro- sion, which may be required in some areas, consult a NISSAN dealer.
Appearance and care 7-7
墌 07.7.25/Z33-D/V5.0 墍
MEMO
7-8 Appearance and care
墌 07.7.25/Z33-D/V5.0 墍
8 Maintenance and do-it-yourself
Maintenance requirements ................................................. 8-2
General maintenance ........................................................... 8-2
Explanation of general maintenance items ............... 8-2
Maintenance precautions ................................................... 8-5
Engine compartment check locations ............................. 8-7
Engine cooling system ........................................................ 8-8
Checking engine coolant level
.................................... 8-8
Changing engine coolant ............................................. 8-9
Engine oil ................................................................................ 8-9
Checking engine oil level .............................................. 8-9
Changing engine oil and filter ................................... 8-10
Automatic transmission fluid ........................................... 8-12
Power steering fluid .......................................................... 8-12
Brake and clutch fluid ....................................................... 8-13
Brake fluid ....................................................................... 8-13
Clutch fluid ..................................................................... 8-14
Window washer fluid ........................................................ 8-14
Battery ................................................................................... 8-15
Jump starting ................................................................. 8-16
Drive belts ............................................................................ 8-17
Spark plugs ......................................................................... 8-17
Replacing spark plugs ................................................ 8-17
Air cleaners .......................................................................... 8-18
Windshield wiper blades ................................................. 8-19
Cleaning ......................................................................... 8-19
Replacing ....................................................................... 8-20
Brakes ................................................................................... 8-21
Self-adjusting brakes .................................................. 8-21
Brake pad wear indicators ......................................... 8-21
Fuses ..................................................................................... 8-21
Engine compartment ................................................... 8-22
Passenger compartment ............................................ 8-23
Keyfob battery replacement.............................................. 8-24
Lights ..................................................................................... 8-26
Headlights ...................................................................... 8-27
Exterior and interior lights .......................................... 8-28
Wheels and tires ................................................................ 8-30
Tire pressure ................................................................. 8-30
Tire labeling..................................................................... 8-34
Types of tires ................................................................. 8-36
Tire chains ...................................................................... 8-37
Changing wheels and tires ........................................ 8-37
墌 07.7.25/Z33-D/V5.0 墍
MAINTENANCE REQUIREMENTS
GENERAL MAINTENANCE
Your new NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that scheduled maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives the proper maintenance care. You are a vital link in the maintenance chain. Scheduled maintenance: For your convenience, both required and op- tional scheduled maintenance items are de- scribed and listed in your “NISSAN Service and Maintenance Guide”. You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance: General maintenance includes those items which should be checked during normal day-to- for proper day operation. They are essential vehicle operation. responsibility to perform these procedures regularly as pre- scribed. 8-2 Maintenance and do-it-yourself
is your
It
Performing general maintenance checks re- quires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, a NISSAN dealer. Where to go for service: If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by a NISSAN dealer. NISSAN technicians are well-trained specialists and are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that a NISSAN dealer’s service department performs the best job to meet the maintenance requirements of your ve- hicle — in a reliable and economic way.
During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have a NISSAN dealer do it promptly. In addition, you should notify a NISSAN dealer if you think that repairs are required. When performing any checks or maintenance work, closely observe the “Maintenance precau- tions” later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with “*” is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood: Check that all doors and the engine hood operate smoothly as well as the trunk lid or back hatch. Also make sure that all latches lock securely. Lubricate if necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released. When driving in areas using road salt or other
墌 07.7.25/Z33-D/V5.0 墍
corrosive materials, check lubrication frequently. Lights*: Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)*: When checking the tires, make sure no nuts are missing, and check for any loose nuts. Tighten if necessary. Tire rotation*: Tires cannot be rotated in this vehicle. Tires*: Check the pressure with a gauge often and always prior to long distance trips. Adjust the pressure in all tires, including the spare, to the pressure specified. Check carefully for dam- age, cuts or excessive wear. Tire Pressure Monitoring System (TPMS) transmitter components: Replace the TPMS transmitter grommet seal, valve core and cap when the tires are replaced due to wear or age. Wheel alignment and balance: If the vehicle pulls to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel align- ment.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be needed.
For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. Windshield: Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other damage. Have a damaged windshield repaired by a qualified re- pair facility. Windshield wiper blades*: Check for cracks or wear if they do not wipe properly. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Automatic transmission P (Park) position mechanism: On a fairly steep hill check that the vehicle is held securely with the selector lever in the P (Park) position without applying any brakes. Accelerator pedal: Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mat away from the pedal.
If
Brake pedal: Check the pedal
for smooth
operation.
the brake pedal suddenly goes
down further than normal, the pedal feels spongy
or the vehicle seems to take longer to stop, see
a NISSAN dealer immediately. Keep the floor
mat away from the pedal.
Brakes: Check that the brakes do not pull the
vehicle to one side when applied. Check the
brake booster function. Be sure to keep floor mat
away from the pedal.
Parking brake: Check the parking brake op-
eration regularly. The vehicle should be securely
held on a fairly steep hill with only the parking
brake applied. If the parking brake needs to be
adjusted, see a NISSAN dealer.
Seats: Check seat position controls such as
seat adjusters, seatback recliner, etc. to ensure
they operate smoothly and that all latches lock
securely in every position. Check that the head
restraints move up and down smoothly and that
the locks (if equipped) hold securely in all
latched positions.
Seat belts: Check that all parts of the seat belt
system (for example, buckles, anchors, adjusters
and retractors) operate properly and smoothly,
and are installed securely. Check the belt web-
bing for cuts, fraying, wear or damage.
Steering wheel: Check for changes in the
Maintenance and do-it-yourself 8-3
墌 07.7.25/Z33-D/V5.0 墍
Underbody: The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances, other- wise rust will form on the floor pan, frame, fuel lines and around the exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, being careful to clean those areas where mud and dirt may accumu- late. For additional information, see “Cleaning exterior” in the “7. Appearance and care” sec- tion. Window washer fluid*: Check that there is adequate fluid in the tank.
steering conditions, such as excessive free play, hard steering or strange noises. Warning lights and chimes: Make sure that all warning lights and chimes are operating prop- erly. Windshield wiper and washer*: Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster: Check that the air comes out of the defroster outlets properly and in good quantity when operating the heater or air conditioner. Under the hood and the vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). Battery*: Check the fluid level in each cell. It should be between the MAX and MIN lines. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Brake and clutch fluid levels*: Make sure that the brake and clutch fluid levels are between the MAX and MIN lines on the reservoir. Engine coolant level*: Check the coolant level when the engine is cold. 8-4 Maintenance and do-it-yourself
Engine drive belts*: Make sure that no belt is frayed, worn, cracked or oily. Engine oil level*: Check the level on the dipstick after parking the vehicle on a level spot, turning off the engine and waiting 10 minutes. Exhaust system: Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately locate the trouble and correct it. (See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas (carbon monoxide).) Fluid leaks: Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected imme- diately. Power steering fluid level* and lines: Check the level in the reservoir tank with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Radiator and hoses: Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, deterioration or loose connections.
墌 07.7.25/Z33-D/V5.0 墍
MAINTENANCE PRECAUTIONS
When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed.
WARNING
쐌 Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. For manual trans- mission models, move the shift lever to N (Neutral) position. For automatic transmission models, move the se- lector lever to P (Park).
쐌 Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.
쐌 If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.
쐌 It is advisable to secure or remove any loose clothing and remove any
jewelry, such as rings, watches, etc. before working on your vehicle.
쐌 Always wear eye protection when-
ever you work on your vehicle.
쐌 If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.
쐌 Never get under the vehicle while it is supported only by a jack. If it is nec- essary to work under the vehicle, support it with safety stands.
쐌 Keep smoking materials, flame and sparks away from the fuel tank and battery.
쐌 On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.
CAUTION
쐌 Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.
쐌 Avoid contact with used engine oil and coolant. Improperly disposed en- gine oil, engine coolant and/or other vehicle fluids can damage the envi- ronment. Always conform to local regulations for disposal of vehicle fluid.
쐌 Never connect or disconnect the bat- tery or any transistorized component while the ignition switch is in the ON position.
쐌 Never leave the engine or automatic transmission related component har- nesses disconnected while the igni- tion switch is in the ON position.
This “8. Maintenance and do-it-yourself” section gives instructions regarding only those items which are relatively easy for an owner to perform.
A genuine NISSAN Service Manual is also avail-
Maintenance and do-it-yourself 8-5
墌 07.7.25/Z33-D/V5.0 墍
able. See “Owner’s Manual/Service Manual or- der information” in the “9. Technical and con- sumer information” section. You should be aware that incomplete or im- proper servicing may result in operating difficul- ties or excessive emissions, and could affect your warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer.
8-6 Maintenance and do-it-yourself
墌 07.7.25/Z33-D/V5.0 墍
ENGINE COMPARTMENT CHECK LOCATIONS
1. Fuse/fusible link holder 2. Battery 3. Engine oil filler cap 4. Brake fluid reservoir 5. Clutch fluid reservoir (M/T models) 6. Window washer fluid reservoir 7. Power steering fluid reservoir 8. Air cleaner 9. Radiator filler cap 10. Engine drive belts 11. Engine coolant reservoir 12. Engine oil dipstick Do not tamper with the strut tower bar adjustment 쎻A . The strut tower bar has been adjusted to the most suitable posi- tion at the factory.
CAUTION
Tampering with the strut tower bar ad- justment may cause a noise while driv- ing or damage to the hood or engine.
SDI2050
Maintenance and do-it-yourself 8-7
墌 07.7.25/Z33-D/V5.0 墍
Outside temperature
down to
°C
−35
°F
−30
Anti- freeze
Deminer-
alized water/ distilled water
50%
50%
CAUTION
When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Antifreeze/Coolant (green) or equivalent with the proper mixture ratio of 50% anti-freeze and 50% demineral- ized water/distilled water. The use of other types of coolant solutions may damage your engine cooling system.
ENGINE COOLING SYSTEM
The engine cooling system is filled at the factory with a high-quality, year-round, anti-freeze cool- ant solution. The anti-freeze solution contains rust and corrosion inhibitors, therefore additional cooling system additives are not necessary.
WARNING
쐌 Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down. Serious burns could be caused by high pressure fluid escap- ing from the radiator. See precau- tions in “If your vehicle overheats” found in the “6. In case of emer- gency” section of this manual.
쐌 The radiator is equipped with a pres- sure type radiator cap. To prevent engine damage, use only a genuine NISSAN radiator cap.
8-8 Maintenance and do-it-yourself
SDI2051
CHECKING ENGINE COOLANT
LEVEL
Check the coolant level
in the reservoir tank
when the engine is cold. If the coolant level is
below MIN 쎻1 , add coolant up to the MAX 쎻2
level. If the reservoir tank is empty, check the
coolant level in the radiator when the engine is
cold. If there is insufficient coolant in the radia-
tor, fill the radiator with coolant up to the filler
opening and also add it to the reservoir tank up
to the MAX 쎻2 level.
Tighten the cap securely after adding engine
coolant.
墌 07.7.25/Z33-D/V5.0 墍
ENGINE OIL
쐌 Keep coolant out of reach of children
and pets.
Engine coolant must be disposed of properly. Check your local regulations.
If the engine cooling system frequently requires coolant, have it checked by a NISSAN dealer. CHANGING ENGINE COOLANT Contact a NISSAN dealer required. 쐌 Major cooling system repairs should be per- formed by a NISSAN dealer. The service procedures can be found in the appropriate NISSAN Service Manual.
replacement
is
if
쐌 Improper servicing can result
in reduced heater performance and engine overheating.
WARNING
쐌 To avoid being scalded, never change the coolant when the engine is hot. 쐌 Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.
쐌 Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
SDI2045
CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it reaches
the operating temperature.
3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the
oil pan.
4. Remove the dipstick and wipe it clean. Rein-
sert it all the way.
Maintenance and do-it-yourself 8-9
墌 07.7.25/Z33-D/V5.0 墍
5. Remove the dipstick again and check the oil level. It should be between the H and L marks 쎻1 . If the oil level is below the L mark 쎻2 , remove the oil filler cap and pour recom- mended oil through the opening. Do not overfill 쎻3 .
6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.
CAUTION
Oil level should be checked regularly. Operating the engine with an insuffi- cient amount of oil can damage the engine, and such damage is not covered by warranty.
CHANGING ENGINE OIL AND FILTER Change the engine oil and filter according to the maintenance log shown in the “NISSAN Service and Maintenance Guide”.
8-10 Maintenance and do-it-yourself
Vehicle set-up 1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it reaches
the operating temperature.
3. Turn the engine off and wait more than 10
minutes.
4. Raise and support the vehicle using a suit-
able floor jack and safety jack stands.
쐌 Place the safety jack stands under the vehicle
jack-up points.
쐌 A suitable adapter should be attached to the
jack stand saddle.
5. Remove the plastic engine undercover. a. Remove the small plastic clip at the center
point of the undercover.
b. Then remove the other bolts that hold the
undercover in place.
SDI2052
Engine oil and filter 1. Place a large drain pan under the drain plug
쎻1 .
2. Remove the oil filler cap. 3. Remove the drain plug with a wrench and
completely drain the oil.
CAUTION
WARNING
Make sure the correct lifting and sup- port points are used to avoid vehicle damage.
쐌 Prolonged and repeated contact with used engine oil may cause skin cancer.
墌 07.7.25/Z33-D/V5.0 墍
쐌 Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
쐌 Keep used engine oil out of reach of
children.
CAUTION
Be careful not to burn yourself, as the engine oil is hot.
쐌 Waste oil must be disposed of properly. 쐌 Check your local regulations. Perform steps 4 to 7 when the engine oil filter change is needed. 4. Loosen the oil filter with an oil filter wrench 쎻2 . Remove the oil filter by turning it by hand. 5. Wipe the engine oil filter mounting surface
with a clean rag.
CAUTION
CAUTION
Be sure to remove any old gasket mate- rial remaining on the mounting surface of the engine. Failure to do so could lead to engine damage.
The dipstick must be inserted in place to prevent oil spillage from the dipstick hole while filling the engine with oil.
6. Coat the gasket on the new filter with clean
engine oil.
7. Screw in the oil filter clockwise until a slight then tighten additionally
resistance is felt, more than 2/3 turn. Oil filter tightening torque:
11 to 15 ft-lb (14.7 to 20.5 N⋅m)
8. Clean and re-install the drain plug and a new washer. Securely tighten the drain plug with a wrench. Drain plug tightening torque:
22 to 29 ft-lb (29 to 39 N⋅m)
Do not use excessive force.
9. Refill engine with recommended oil and in-
stall the cap securely.
See “Capacities and recommended fuel/ lubricants” in the “9. Technical and consumer information” section for drain and refill capac- ity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine the proper amount of oil in the engine.
10. Start
the engine and check for leakage filter.
around the drain plug and the oil Correct as required.
11. Turn the engine off and wait more than 10
level with the dip-
minutes. Check the oil stick. Add engine oil if necessary.
After the operation 1.
Install the engine undercover into position as outlined in the following steps.
a. Pull the center of the small plastic clip out. b. Hold the engine undercover into position. c.
Insert the clip through the undercover into the
Maintenance and do-it-yourself 8-11
墌 07.7.25/Z33-D/V5.0 墍
d.
hole in the frame, then push the center of the clip in to lock the clip in place. Install the other bolts that hold the under- cover in place. Be careful not to strip the bolts or over-tighten them.
2. Lower the vehicle carefully to the ground. 3. Dispose of waste oil and filter properly.
AUTOMATIC TRANSMISSION FLUID When checking or replacement is required, we recommend a NISSAN dealer for servicing.
CAUTION
쐌 Use only Genuine NISSAN Matic J
ATF. Do not mix with other fluids.
쐌 Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in drive- ability and automatic transmission durability, and may damage the auto- matic transmission, which is not cov- ered by the NISSAN new vehicle lim- ited warranty.
POWER STEERING FLUID
SDI1443
Check the fluid level in the reservoir tank. The fluid level should be checked using the HOT range at fluid temperatures of 122 - 176°F (50 - 80°C) or using the COLD range at fluid tem- peratures of 32 - 86°F (0 - 30°C). If the fluid is below the MIN line, add Genuine NISSAN PSF fluid. Remove the cap and fill through the opening.
8-12 Maintenance and do-it-yourself
墌 07.7.25/Z33-D/V5.0 墍
CAUTION
쐌 Do not overfill. 쐌 Recommended fluid is Genuine
NISSAN PSF or equivalent.
For more information regarding suitable equiva- lents, see “Capacities and recommended fuel/lubricants” in the “9. Technical and con- sumer information” section.
BRAKE AND CLUTCH FLUID
For additional brake and clutch fluid information, refer to “Capacities and recommended fuel/ lubricants” in the “9. Technical and consumer information” section of this manual.
WARNING
쐌 Use only new fluid from a sealed container. Old, inferior or contami- nated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle’s stopping ability. 쐌 Clean the filler cap before removing. 쐌 Brake fluid is poisonous and should be stored carefully in marked con- tainers out of the reach of children.
CAUTION
Do not spill the fluid on any painted surfaces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.
SDI1923
BRAKE FLUID Check the fluid level in the reservoir. If the fluid is below the MIN line 쎻2 or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line 쎻1 . If fluid must be added fre- quently, the system should be thoroughly checked by a NISSAN dealer.
Maintenance and do-it-yourself 8-13
墌 07.7.25/Z33-D/V5.0 墍
WINDOW WASHER FLUID
SDI1906
SDI2053
CLUTCH FLUID Check the fluid level in the reservoir. If the fluid is below the MIN line 쎻2 , add Genuine level NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line 쎻1 . If fluid is added frequently, the system should be thoroughly checked by a NISSAN dealer.
Add fluid when the low washer fluid warning light comes on. Add a washer solvent to the washer fluid for better cleaning. In the winter season, add a windshield washer anti-freeze. Follow the manu- facturer’s instructions for the mixture ratio. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.
WARNING
Anti-freeze is poisonous and should be stored carefully in marked containers out of the reach of children.
CAUTION
쐌 Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint.
쐌 Do not fill the window washer reser- voir tank with washer fluid concen- trates at full strength. Some methyl alcohol based washer fluid concen- trates may permanently stain the grille if spilled while filling the win- dow washer reservoir tank.
쐌 Pre-mix washer fluid concentrates with water to the manufacturer’s rec- ommended levels before pouring the fluid into the window washer reser- voir tank. Do not use the window
8-14 Maintenance and do-it-yourself
墌 07.7.25/Z33-D/V5.0 墍
washer reservoir tank to mix the washer fluid concentrate and water.
BATTERY
쐌 Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water.
쐌 Make certain the terminal connections are
clean and securely tightened.
쐌 If the vehicle is not to be used for 30 days or longer, disconnect the (−) negative battery terminal to prevent discharging it.
CAUTION
When the battery cable is removed from the battery terminal, do not close either of the front doors. The automatic win- dow adjusting function will not work, and the side roof panel/top side rail may be damaged by doing so.
To disconnect the negative (−) battery ter- minal, perform the procedure in the follow- ing order. Otherwise, the window and the side roof panel/top side rail may contact and be damaged.
1. Close the windows.
2. Open the hood.
3. Close and lock all the doors using the
key or keyfob.
4. Disconnect the negative (−) battery ter-
minal.
5. Securely close the hood. To connect the negative (−) battery termi- nal, perform the procedure in the following order. Otherwise, the window and the side roof panel/top side rail may contact and be damaged. 1. Unlock (using the key) and open the driver side door. Do not close the door.
2. Open the hood. 3. Connect the negative (−) battery termi-
nal. Then close the hood.
4. Fully open the driver side door window. 5. Close the driver side door and the win-
dow.
WARNING
쐌 Do not expose the battery to flames or electrical sparks. Hydrogen gas, generated by battery fluid, is explo- sive. Do not allow battery fluid to
Maintenance and do-it-yourself 8-15
墌 07.7.25/Z33-D/V5.0 墍
contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention.
쐌 Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the bat- tery which can generate heat, reduce battery life, and in some cases lead to an explosion.
쐌 When working on or near a battery, always wear suitable eye protection and remove all jewelry.
쐌 Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after han- dling.
쐌 Keep the battery out of the reach of
children.
8-16 Maintenance and do-it-yourself
DI0137MA
SDI1480
JUMP STARTING If jump starting is necessary, see “Jump starting” in the “6. In case of emergency” section. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.
Check the fluid level in each cell. It should be between the UPPER LEVEL 쎻1 and LOWER LEVEL 쎻2 lines. If it is necessary to add fluid, add only distilled water to bring the level to the indicator in each filler opening. Do not overfill. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. 1. Remove the cell plugs 쎻A . 2. Add distilled water up to the UPPER LEVEL
line 쎻1 .
3. Tighten cell plugs.
墌 07.7.25/Z33-D/V5.0 墍
unexpectedly.
1. Visually inspect each belt for signs of unusual wear, cuts, fraying, oil adhesion or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by a NISSAN dealer. 2. Have the belts checked regularly for condi-
tion.
SPARK PLUGS
REPLACING SPARK PLUGS If replacement is required, see a NISSAN dealer for servicing.
WARNING
Be sure the engine and ignition switch are off and that the parking brake is engaged securely.
CAUTION
Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.
DRIVE BELTS
SDI2061
1. Power steering fluid pump
2. Alternator
3. Crankshaft pulley
4. Air conditioner compressor
5. Drive belt auto-tensioner
WARNING
Be sure the ignition key is in the OFF or LOCK position before servicing drive belts. rotate
engine
could
The
Maintenance and do-it-yourself 8-17
墌 07.7.25/Z33-D/V5.0 墍
AIR CLEANERS
the inside of the air cleaner housing and the cover with a damp cloth.
WARNING
쐌 Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it is not there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.
쐌 Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.
SDI2054
To remove the filter from the air cleaner, pull off the retainers 쎻1 and pull the unit upward 쎻2 . The filter element should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide”. When replacing the filter, wipe
墌 07.7.25/Z33-D/V5.0 墍
SDI2020
Iridium-tipped spark plugs It is not necessary to replace the iridium-tipped spark plugs as frequently as the conventional type spark plugs since they will last much longer. Follow the maintenance log shown in the “NISSAN Service and Maintenance Guide”, but do not service iridium-tipped spark plugs by cleaning or regapping. Always replace spark plugs with recom- mended or equivalent ones.
8-18 Maintenance and do-it-yourself
WINDSHIELD WIPER BLADES
CAUTION
rinse the blade with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.
쐌 After wiper blade replacement, return the wiper arm to its original position.
Otherwise it may be damaged when the engine hood is opened.
쐌 Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure.
쐌 Worn windshield wiper blades can damage the windshield and impair driver vision.
CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield.
Clean the outside of the windshield with a washer solution or a mild detergent. Your wind- shield is clean if beads do not form when rinsing with clear water.
Clean the blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then
Maintenance and do-it-yourself 8-19
墌 07.7.25/Z33-D/V5.0 墍
REPLACING Replace the wiper blades if they are worn. 1. Pull the wiper arm. 2. Push the release tab 쎻A , then move the wiper
blade down the wiper arm to remove 쎻1 . Insert the new wiper blade onto the wiper arm until a click sounds.
3.
8-20 Maintenance and do-it-yourself
SDI1649
SDI1730A
If necessary, clean the windshield washer nozzle 쎻A with a needle or small pin 쎻B . *1: Only for passenger’s side wiper arm *2: Adjustable washer nozzles
墌 07.7.25/Z33-D/V5.0 墍
BRAKES
If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Your vehicle is equipped with self-adjusting brakes.
The disc-type brakes self-adjust every time the brake pedal is applied.
WARNING
See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal.
BRAKE PAD WEAR INDICATORS The disc brake pads on your vehicle have au- dible wear indicators. When a brake pad re- quires replacement, it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect
FUSES
the function or performance of the brake system. Proper brake inspection intervals should be followed. For additional information, see the appropriate maintenance log shown in the NISSAN Service and Maintenance Guide.
SDI1751
Some vehicles are equipped with engine com- partment and passenger compartment fuse boxes that use only type 쎻A fuses. Other ve- hicles are equipped with type 쎻A fuses in the engine compartment fuse box and type 쎻B fuses in the passenger compartment fuse box. Type 쎻A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type 쎻A fuses can be installed in the engine compartment and passenger compartment fuse boxes.
Maintenance and do-it-yourself 8-21
墌 07.7.25/Z33-D/V5.0 墍
SDI1752
If a type 쎻A fuse is used to replace a type 쎻B
fuse, the type 쎻A fuse will not be level with the
fuse pocket as shown in the illustration. This will
not affect the performance of the fuse. Make
sure the fuse is installed in the fuse box securely.
Type 쎻B fuses cannot be installed in the under-
hood fuse boxes. Only use type 쎻A fuses in the
underhood fuse boxes.
8-22 Maintenance and do-it-yourself
SDI1479B
SDI1753
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage rating than that specified on the fuse box cover. This could damage the electrical system or cause a fire.
If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and headlight
switch are OFF.
2. Open the engine hood and remove the cover on the battery and the fuse/fusible link holder.
3. Remove the fuse/fusible link holder cover by pushing the tabs 쎻1 and lifting the cover 쎻2 . 4. Remove the fuse with the fuse puller. The fuse puller is located in the passenger com- partment fuse box. If the fuse is open 쎻A , replace it with a new fuse 쎻B . Spare fuses are stored in the pas- senger compartment fuse box.
5.
6.
If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.
墌 07.7.25/Z33-D/V5.0 墍
Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts.
SDI1962
2. Open the fuse box lid 쎻1 . 3. Pinch the fuse perpendicularly with the fuse
puller 쎻2 and pull it out.
PASSENGER COMPARTMENT
CAUTION
Never use a fuse of a higher or lower amperage rating than that specified on the fuse box cover. This could damage the electrical system or cause a fire.
If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight
switch are OFF.
Maintenance and do-it-yourself 8-23
墌 07.7.25/Z33-D/V5.0 墍
KEYFOB BATTERY REPLACEMENT
CAUTION
Be careful not to allow children to swal- low the battery and removed parts.
4.
5.
SDI1754
If the fuse is open 쎻A , replace it with a new
fuse 쎻B . Spare fuses 쎻3 are stored in the
fuse box.
If a new fuse also opens, have the electrical
system checked and repaired by a NISSAN
dealer.
8-24 Maintenance and do-it-yourself
SDI1608
Replace the battery as follows:
1. Open the lid using a suitable tool. 2. Replace the battery with a new one.
Recommended battery: CR2025 or equivalent
墌 07.7.25/Z33-D/V5.0 墍
approved by the party responsible for com- pliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.
Make sure that the ⊕ side faces the bottom case.
쐌 Do not touch the internal circuit and electric terminals as doing so could cause a malfunc- tion.
3. Close the lid securely.
4. Push the keyfob button two or three times to
check its operation.
See a NISSAN dealer if you need any assistance
for replacement.
If the battery is removed for any reason
other than replacement, perform step 4
above.
쐌 Be careful not to touch the circuit board
and the battery terminal.
쐌 An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal.
쐌 The keyfob is water-resistant; however, if it gets wet, immediately wipe it com- pletely dry.
쐌 When changing batteries, do not let
dust or oil get on the keyfob.
FCC Notice: Changes or modifications not expressly
Maintenance and do-it-yourself 8-25
墌 07.7.25/Z33-D/V5.0 墍
LIGHTS
쎻1 Front view 1. Headlight (low-beam, high-beam) 2. Spot light 3. Front park light 4. Front turn signal light 5. Front side marker light 쎻2 Rear view (Coupe), 쎻3 Rear view (Roadster) 6. Luggage compartment light (Coupe) or Trunk
light (Roadster)
7. High-mounted stop light 8. Rear combination light (Side marker, Stop/Tail)
9. License plate lights 10. Rear combination light (Back-up, Turn signal)
8-26 Maintenance and do-it-yourself
SDI2058
墌 07.7.25/Z33-D/V5.0 墍
HEADLIGHTS Replacing If replacement is required, see a NISSAN dealer. Xenon headlight bulb:
WARNING
HIGH VOLTAGE
When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer. For additional information, see “Headlight and turn signal switch” in the “2. Instruments and controls” sec- tion.
CAUTION
Use the same number and wattage as originally installed: Bulb no. (Wattage) D2S (35W) - Xenon low/high-beam
Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer.
Maintenance and do-it-yourself 8-27
墌 07.7.25/Z33-D/V5.0 墍
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Front turn signal light*
Front park light*
Front side marker light*
Rear combination light (Upper)
Stop/Tail*
Side marker*
Rear combination light (Lower)
Back-up*
Turn signal*
License plate light (x 2)
High-mounted stop light*
Spot light
Luggage compartment light (Coupe)
Trunk light (Roadster)*
Vanity mirror light
Cup holder light*
Rear floor box light*
28/8
(LED)
(LED)
(LED)
21
21
(LED)
3.4
1.8
1.1
1.4
Bulb No.
3457NA
T10
—
—
—
T20
T20
T10
—
—
—
—
—
—
—
*: See a NISSAN dealer for replacement. NOTE: Always check with the Parts Department at a NISSAN dealer for the latest information about parts.
8-28 Maintenance and do-it-yourself
MDI0006
Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.
墌 07.7.25/Z33-D/V5.0 墍
SDI1779
SDI1572
Interior light (Roadster) Be careful not to snap the nails 쎻A on the plastic cover when removing it.
SDI1450A
Maintenance and do-it-yourself 8-29
SDI1451
墌 07.7.25/Z33-D/V5.0 墍
WHEELS AND TIRES
TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). For more details, refer to “Low tire pressure warning light” in the “2. Instruments and con- trols” section, “Tire pressure monitoring system (TPMS)” in the “5. Starting and driving” section, and “Flat tire” in the “6. In case of emergency” section.
SDI1401A
Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label under the “COLD TIRE PRESSURE” heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: 쐌 Most tires naturally lose air over time. 쐌 Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.
The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at mod- erate speeds.
8-30 Maintenance and do-it-yourself
墌 07.7.25/Z33-D/V5.0 墍
Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.
WARNING
쐌 Improperly inflated tires can fail suddenly and cause an acci- dent.
쐌 The Gross Vehicle Weight Rat- ing (GVWR) is located on the F.M.V.S.S./C.M.V.S.S. certifica- tion label. The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle be- yond this capacity. Overloading your vehicle may result in re- duced tire life, unsafe operating conditions due to premature tire failure, or unfavorable han- dling characteristics and could also lead to a serious accident. Loading beyond the specified
capacity may also result in fail- ure of other vehicle compo- nents.
쐌 Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.
쐌 Do not drive your vehicle over
85 MPH (137 km/h) unless it is
equipped with high speed rated
tires. Driving faster
than 85
MPH (137 km/h) may result in
tire failure, loss of control and
possible injury.
쐌 For additional information re- garding tires, refer to “Impor- tant Tire Safety Information” (US) or “Tire Safety Informa- tion” (Canada) in the Warranty Information Booklet.
Maintenance and do-it-yourself 8-31
墌 07.7.25/Z33-D/V5.0 墍
originally installed on the vehicle at the factory.
쎻4 Cold tire pressure: Inflate the tires to
this pressure when the tires are cold.
Tires are considered COLD after the
vehicle has been parked for 3 or
more hours, or driven less than 1
mile (1.6 km) at moderate speeds.
The recommended cold tire inflation
is set by the manufacturer to provide
the best balance of tire wear, vehicle
handling, driveability, tire noise, etc.,
up to the vehicle’s GVWR.
쎻5 Tire size — refer to “Tire labeling”
later in this section.
쎻6 Spare tire size or compact spare tire
size (if so equipped).
Tire and Loading Information label 쎻1 Seating capacity: The maximum number of occupants that can be seated in the vehicle.
8-32 Maintenance and do-it-yourself
SDI1948
쎻2 Vehicle load limit: See loading infor- mation in the “Technical and con- sumer information” section.
쎻3 Original size: The size of the tires
墌 07.7.25/Z33-D/V5.0 墍
3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare it to the specifica- tion shown on the Tire and Loading Information label.
5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Re- check the pressure and add or release air as needed.
6. Install the valve stem cap. 7. Check the pressure of all other tires,
including the spare.
SDI1949
Checking the tire pressure 1. Remove the valve stem cap from the
tire.
2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leak- age.
Coupe model
Front Original Tire Rear Original Tire Spare Tire
Size
Cold Tire Inflation Pressure
225/45R18
245/40R18
240 kPa (35 psi)
245/45R18
265/35R19
T145/80D17
Roadster model
Size
Front Original Tire Rear Original Tire Spare Tire
225/45R18
245/45R18
T145/80D17
240 kPa (35 psi)
420 kPa (60 psi)
Cold Tire Inflation Pressure
240 kPa (35 psi)
240 kPa (35 psi)
420 kPa (60 psi)
Maintenance and do-it-yourself 8-33
墌 07.7.25/Z33-D/V5.0 墍
tire’s ratio of height to width. 4. R: The “R” stands for radial. 5. Two-digit number (15): This number is
the wheel or rim diameter in inches.
6. Two- or three-digit number (95): This number is the tire’s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.
7. Tire Speed Rating. You should not drive the vehicle faster than the tire speed rating.
SDI1575
Example
TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.
8-34 Maintenance and do-it-yourself
쎻1 Tire size (example: P215/65R15
Example
SDI1951
95H)
1. P: The “P” indicates the tire is de- signed for passenger vehicles. (Not all tires have this information.)
2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to sidewall edge.
3. Two-digit number (65): This number, known as the aspect ratio, gives the
墌 07.7.25/Z33-D/V5.0 墍
4. Three-digit code: Tire type code (Op-
tional)
5. Three-digit code: Date of Manufacture 6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.
쎻3 Tire ply composition and material
The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 쎻4 Maximum permissible inflation pres-
sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.
쎻5 Maximum load rating
This number indicates the maximum
SDI1607
Example
쎻2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX)
1. DOT: Abbreviation for the “Depart- ment of Transportation”. The symbol can be placed above, below or to the left or right of the Tire Identification Number.
2. Two-digit code: Manufacturer’s identi-
fication mark
3. Two-digit code: Tire size
load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.
쎻6 Term of “tubeless” or “tube type”
Indicates whether the tire requires an inner tube (“tube type”) or not (“tubeless”).
쎻7 The word “radial”
The word “radial” is shown if the tire has radial structure.
쎻8 Manufacturer or brand name
Manufacturer or brand name is shown.
Other tire-related terminology:
In addition to the many terms that are
defined throughout this section, Intended
Outboard Sidewall is (1) the sidewall that
contains a whitewall, bears white letter-
ing or bears manufacturer, brand, and/or
model name molding that is higher or
deeper than the same molding on the
Maintenance and do-it-yourself 8-35
墌 07.7.25/Z33-D/V5.0 墍
(2)
the tire, or
the other sidewall of outward facing sidewall of an asymmetri- cal tire that has a particular side that must always face outward when mounted on a vehicle. TYPES OF TIRES
WARNING
쐌 When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.
than
rating
쐌 Replacement tires may have a lower factory speed equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.
the
쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the proper operation of the tire
8-36 Maintenance and do-it-yourself
If you do not,
Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you operate your vehicle in snowy or icy conditions, NISSAN recommends the use of snow or all season tires on all four wheels. For additional traction on icy roads, studded tires may be used. However, some provinces and states prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires, on wet or dry surfaces, may be poorer than that of non-studded snow tires.
pressure monitoring system (TPMS). 쐌 For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety In- formation” (Canada) in the Warranty Information Booklet.
All season tires NISSAN specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance in snow and ice will be substantially reduced. Summer tires do not have the tire traction rating M&S on the tire sidewall.
If you operate your vehicle in snowy or icy conditions, NISSAN recommends the use of snow or all season tires on all four wheels.
墌 07.7.25/Z33-D/V5.0 墍
TIRE CHAINS
CAUTION
Tire chains/cables should not be in- stalled on 265/35R19 size tires. Installa- tion of the tire chains/cables on 265/35R19 size tires will cause damage to the vehicle. If you plan to use tire chains/cables, install 245/45R18 size tires on your vehicle.
should
you
Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class “S” chains are designed to meet the SAE standard minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recom-
mended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your ve- hicle may be damaged and/or vehicle handling and performance may be adversely affected. 쐌 Never install the tire chains on a T-type
spare tire.
쐌 Do not use the tire chains on dry roads. 쐌 Tire chains must be installed only on the rear wheels and not on the front wheels.
CHANGING WHEELS AND TIRES Tire rotation Tires cannot be rotated in this vehicle, as front tires are different size from rear tires and the direction of wheel rotation is fixed in each tire. A pin is on the front brake rotor to prevent the rear wheels from being installed in place of the front wheels. The spare tire can be installed in place of the front and rear wheels. When installing the spare tire in the front wheel, the hole in the spare tire wheel must be aligned with the pin on the brake rotor.
WARNING
쐌 Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).
쐌 For additional information regarding tires, refer to “Important Tire Safety
Maintenance and do-it-yourself 8-37
墌 07.7.25/Z33-D/V5.0 墍
Information” (US) or “Tire Safety In- formation” (Canada) in the Warranty Information Booklet.
the tire(s) should be replaced. 쐌 The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.
쐌 Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious. Replace the tires as necessary to prevent tire failure and possible personal injury.
쐌 Improper service of the spare tire may result in serious per- sonal injury. If it is necessary to repair the spare tire, contact a NISSAN dealer.
쐌 For additional information re- garding tires, refer to “Impor- tant Tire Safety Information” (US) or “Tire Safety Informa-
SDI1663
1. Wear indicator 2. Wear indicator location mark Tire wear and damage
WARNING
쐌 Tires should be periodically in- spected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found,