stopped before shifting the selector lever. This automatic transmission model is de- signed so that the foot brake pedal must be depressed before shifting from P (Park) to any drive position while the ignition switch is ON. The selector lever cannot be moved out of P (Park) position and into any of the other gear positions if the ignition key is turned to the LOCK, OFF or ACC position or if the key is removed from the ignition switch. 5-10 Starting and driving
1. Keep the foot brake pedal depressed and push the selector lever button to shift into a driving gear.
2. Release the parking brake and foot brake,
then gradually start the vehicle in motion.
WARNING
쐌 Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive) or manual shift mode. Always depress the brake pedal until shifting is com- pleted. Failure to do so could cause you to lose control and have an acci- dent.
쐌 Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.
쐌 On slippery roads, do not downshift.
This may cause a loss of control.
쐌 Never shift to P (Park) or R (Reverse) while the vehicle is moving forward.
墌 07.7.25/Z33-D/V5.0 墍
WARNING
Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious per- sonal injury or property damage.
If the key is turned to OFF or ACC for any reason while the vehicle is in R (Reverse), N (Neutral), or any D (Drive) position, the key cannot be turned to LOCK and be removed from the ignition switch. Move the selector lever to the P (Park) position, then the key can be turned to LOCK.
CAUTION
To prevent automatic transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is com- pletely stopped.
P (Park): Use this selector position when the vehicle is parked or when starting the engine. Make sure
the vehicle is completely stopped. The brake
pedal must be depressed and the selector
lever button pushed in to move the selec-
tor lever from N (Neutral) or any drive
position to P (Park). Apply the parking brake.
When parking on a hill, first depress the foot
brake pedal, apply the parking brake, then shift
into the P (Park) position.
R (Reverse):
Use this position to back up. Always be sure the
vehicle is completely stopped before selecting R
(Reverse). The brake pedal must be de-
pressed and the selector
lever button
pushed in to move the selector lever from
P (Park), N (Neutral) or any drive position
to R (Reverse).
N (Neutral):
Neither forward nor reverse gear is engaged.
The engine can be started in this position. You
may shift to N (Neutral) and restart a stalled
engine while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
Manual shift mode
When the selector lever is shifted from D to the
manual shift gate with the vehicle stopped or
while driving, the transmission enters the manual
Starting and driving 5-11
墌 07.7.25/Z33-D/V5.0 墍
SSD0346
To move the selector lever,
: Push the button while depressing the
brake pedal,
: Push the button, : Just move the selector lever.
Shifting After starting the engine, fully depress the brake pedal and shift the selector lever from P (Park) to R (Reverse), N (Neutral), D (Drive), or Manual shift mode position. Push the button to shift into P (Park) or R (Reverse). All other positions can be selected without pushing the button.
shift mode. Shift range can be selected manu- ally.
In the manual shift mode, the shift range is displayed on the position indicator in the meter.
Shift ranges up or down one by one as follows:
→
← M5
→
← M3
→
← M4
→
← M2
M1
M5 (5th):
Use this position for all normal forward driving at
highway speeds.
M4 (4th):
Use this position when driving up long slopes, or
for engine braking when driving down long
slopes.
M3 (3rd) and M2 (2nd):
Use for hill climbing or engine braking on down-
hill grades.
M1 (1st):
Use this position when climbing steep hills
slowly or driving slowly through deep snow,
sand or mud, or for maximum engine braking on
steep downhill grades.
쐌 Remember not to drive at high speeds for
extended periods of time in lower than M4
range. This reduces fuel economy.
5-12 Starting and driving
transmission down into the lower gear, depend- ing on the vehicle speed. Fail-safe When fail-safe operation occurs, the automatic transmission will be locked in 4th gear. If the vehicle is driven under extreme con- ditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition key OFF and wait for 3 seconds. Then turn the key back to the ON position. The vehicle should return to its normal operating con- dition. If it does not return to its normal operating condition, have a NISSAN dealer check the transmission and repair if neces- sary.
쐌 When shifting up, move the selector lever to
the + (up) side. (Shifts to higher range.)
쐌 When shifting down, move the selector lever to the − (down) side. (Shifts to lower range.) 쐌 Moving the selector lever to the same side twice will shift the ranges in succession. However, if this motion is rapidly done, the second shifting may not be completed prop- erly.
쐌 In the manual shift mode, the transmis- sion automatically shifts down to 1st gear before the vehicle comes to a stop. When accelerating again, it is necessary to shift up to the desired range.
쐌 When canceling the manual shift mode, re- turn the selector lever to the D position. The transmission returns to the normal driving mode.
쐌 In the manual shift mode, the transmis- sion may not shift to the selected gear. This helps maintain driving performance and reduces the chance of vehicle dam- age or loss of control. Accelerator downshift — In D position — For passing or hill climbing, fully depress the accelerator pedal to the floor. This shifts the
墌 07.7.25/Z33-D/V5.0 墍
SSD0347
SSD0536
Shift lock release If the battery charge is low or discharged, the select lever may not be moved from the P (Park) position even with the brake pedal depressed. To move the selector lever, depress the brake pedal, apply the parking brake, and push the shift lock release button by using a suitable tool as shown. Push the selector lever button, then the selector lever can be moved to N (Neutral). This allows the vehicle to be moved if the battery is discharged. If the lever cannot be moved out of P (Park), have a NISSAN dealer check the automatic transmis- sion system as soon as possible.
MANUAL TRANSMISSION Shifting To change gears, or when upshifting or down- shifting, fully depress the clutch pedal, shift into the appropriate gear then slowly and smoothly release the clutch.
This vehicle is equipped with a short throw shifter manual transmission. To ensure smooth gear changes, fully depress the clutch pedal before operating the shift lever. If the clutch pedal is not fully depressed before the transmis- sion is shifted, a gear noise may be heard. Transmission damage could occur.
Start the vehicle in 1st gear and shift to 2nd, 3rd, 4th and 5th up to 6th gear in sequence accord- ing to the vehicle speed. To back up, depress the shift lever and then move it to the R (Reverse) position after stop- ping the vehicle completely. If it is difficult to move the shift lever into R (Reverse) or 1 (Low gear), shift to N (Neutral), then release the clutch pedal. Fully depress the clutch pedal again and shift into R or 1.
WARNING
쐌 Do not downshift abruptly on slip- pery roads. This may cause a loss of control.
쐌 Do not over-rev the engine when shifting to a lower gear. This may cause a loss of control or engine damage.
CAUTION
쐌 Do not rest your foot on the clutch pedal while driving. This may damage the clutch.
Starting and driving 5-13
墌 07.7.25/Z33-D/V5.0 墍
쐌 Fully depress the clutch pedal before shifting to help prevent transmission damage.
쐌 Stop your vehicle completely before
shifting into R (Reverse).
쐌 When the vehicle is stopped with the engine running (for example, at a stop light), shift to N (Neutral) and release the clutch pedal with the foot brake applied.
computer display. See “Trip computer” in the “2. Instruments and controls” section for the display setting information. Use the up-shift indicator when driving as fol- lows: 쐌 If the maximum engine speed is desired, set the figure at 7,500 rpm. (The indicator starts flashing from about 7,000 rpm and comes on steady at 7,500 rpm.)
쐌 If the maximum engine torque is desired, set the figure at 4,800 rpm. (The indicator starts flashing from about 4,300 rpm and comes on steady at 4,800 rpm.)
쐌 If you want to break in your vehicle, use of the up-shift indicator with a rather low figure will help you to avoid the high engine speed.
To make the up-shift indicator not come on, set the figure at above 8,100 rpm. There may be a slight difference between the timing of the up-shift indicator illumi- nation and the tachometer indication.
SSD0638
Up-shift indicator The manual transmission up-shift indicator is located in the tachometer and shows the driver the timing to shift into a higher gear by illuminat- ing. The use of the up-shift indicator will help you to upshift at a constant engine speed (rpm) from any gear.
The up-shift indicator will start flashing when the engine speed is within about 500 rpm of the set figure while driving, and then illuminate after the engine speed reaches the set figure.
The engine speed in revolutions per minute (rpm) for upshifting can be set on the trip
5-14 Starting and driving
墌 07.7.25/Z33-D/V5.0 墍
Suggested up-shift speeds Shown below are suggested vehicle speeds for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual up-shift speeds will vary according to road conditions, the weather and individual driv- ing habits. For normal acceleration in low altitude areas [less than 4,000 ft (1,219 m)]:
Gear change 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th
MPH (km/h)
8 (13) 16 (26) 25 (40) 28 (45) 33 (53)
For quick acceleration in low altitude areas or in high altitude areas [over 4,000 ft (1,219 m)]:
Gear change 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th
MPH (km/h)
15 (24) 25 (40) 40 (64) 45 (72) 50 (80)
Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will ensure safe operation. Do not over-rev the en- gine when shifting to a lower gear as it may cause engine damage or loss of vehicle control.
Gear 1st 2nd 3rd 4th 5th 6th
MPH (km/h)
40 (65) 66 (106) 95 (152)
— — —
PARKING BRAKE
SPA2110
To apply: pull the parking brake lever up 쎻1 .
To release:
1. Firmly apply the foot brake.
2. Automatic transmission models:
Move the selector lever to the P (Park) posi- tion. Manual transmission models: Place the shift lever in the N (Neutral) posi- tion.
3. While pulling up on the parking brake lever slightly, push the button 쎻2 and lower the lever completely 쎻3 .
Starting and driving 5-15
墌 07.7.25/Z33-D/V5.0 墍
4. Before driving, be sure the brake warning
light goes out.
WARNING
쐌 Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.
쐌 Do not release the parking brake
from outside the vehicle.
쐌 Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully en- gaged.
쐌 Do not leave children unattended in a vehicle. They could release the park- ing brake and cause an accident.
5-16 Starting and driving
CRUISE CONTROL (if so equipped)
WARNING
cause engine damage.
Do not use the cruise control when driv- ing under the following conditions: 쐌 When it is not possible to keep the
vehicle at a set speed.
쐌 In heavy traffic or in traffic that varies
in speed.
쐌 On winding or hilly roads. 쐌 On slippery roads (rain, snow,
ice,
etc.).
쐌 In very windy areas. Doing so could cause a loss of vehicle control and result in an accident.
CAUTION
On manual transmission models, do not shift into N (Neutral) without depressing the clutch pedal when the cruise control is set. Should this occur, depress the clutch pedal and turn the main switch off immediately. Failure to do so may
PRECAUTIONS ON CRUISE CONTROL 쐌 If the cruise control system malfunctions, it cancels automatically. The SET indicator light on the meter panel then blinks to warn the driver.
쐌 If the engine coolant temperature becomes excessively high, the cruise control system will be canceled automatically.
쐌 If
the SET indicator light blinks,
turn the cruise control MAIN (ON⋅OFF) switch off and have the system checked by a NISSAN dealer.
쐌 The SET indicator light may blink when the cruise control MAIN switch is turned on while pushing the RES/ACCEL, COAST/SET, or CANCEL switch. To properly set the cruise control system, perform the preceding steps in the order indicated.
墌 07.7.25/Z33-D/V5.0 墍
To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. (The SET indicator light will come on.) Take your foot off the accelerator pedal. Your vehicle will maintain the set speed. 쐌 To pass another vehicle, depress the ac- celerator pedal. When you release the pedal, the vehicle will return to the previously set speed.
쐌 The vehicle may not maintain the set speed If this
when going up or down steep hills. happens, drive without the cruise control.
SSD0528
To cancel the preset speed, use one of the following three methods:
1. ACCEL or RESUME switch
2. COAST or SET switch
3. CANCEL switch 4. MAIN (ON⋅OFF) switch CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 to 89 MPH (40 to 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the MAIN switch on. The CRUISE indicator light on the meter panel will come on.
a) Push the CANCEL switch; The SET indicator
light will go out.
b) Tap the brake pedal; The SET indicator light
will go out.
c) Turn the MAIN switch off. Both the CRUISE indicator and SET indicator lights will go out. 쐌 If you depress the brake pedal while pushing the ACCEL/RES set switch and reset at the cruising speed, turn the MAIN switch off once and then turn it on again.
쐌 The cruise control will automatically be can- celled if the vehicle slows down more than
approximately 8 MPH (13 km/h) below the set speed.
쐌 If you depress the clutch pedal (manual trans- mission) or move the selector lever to N (Neutral) position (automatic transmission), the cruise control will be canceled.
To reset at a faster cruising speed, use one of the following three methods:
a) Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.
b) Push and hold the ACCEL/RES set switch. When the vehicle attains the speed you desire, release the switch.
c) Push, then quickly release the ACCEL/RES
set switch. Each time you do this, the set
speed will
increase by about 1 MPH (1.6
km/h).
To reset at a slower cruising speed, use one of the following three methods:
a) Lightly tap the brake pedal. When the vehicle the
the desired speed, push
attains COAST/SET switch and release it.
b) Push and hold the COAST/SET switch. Re- lease the switch when the vehicle slows down to the desired speed.
Starting and driving 5-17
墌 07.7.25/Z33-D/V5.0 墍
c) Push,
then quickly release the COAST/
SET switch. Each time you do this, the set
speed will decrease by about 1 MPH (1.6
km/h).
To resume the preset speed, push and re- lease the ACCEL/RES set switch. The vehicle will resume the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
BREAK-IN SCHEDULE
INCREASING FUEL ECONOMY
CAUTION
During the first 1,200 miles (2,000 km), follow these recommendations to ob- tain maximum engine performance and ensure and economy of your new vehicle. Failure to follow these recommendations may re- sult in shortened engine life and re- duced engine performance.
reliability
future
the
쐌 Avoid driving for long periods at constant speed, either fast or slow. Do not run the engine over 4,000 rpm.
쐌 Do not accelerate at full throttle in any gear. 쐌 Avoid quick starts. 쐌 Avoid hard braking as much as possible. 쐌 Do not tow a trailer for the first 500 miles
(800 km).
쐌 Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position.
쐌 Drive at moderate speeds on the highway. Driving at high speed will lower fuel economy. 쐌 Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.
쐌 Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.
쐌 Avoid unnecessary engine idling. 쐌 Keep your engine tuned up. 쐌 Follow the recommended periodic mainte-
nance schedule.
쐌 Keep the tires inflated to the correct pres- sure. Low tire pressure will increase tire wear and lower fuel economy.
쐌 Keep the front wheels in correct alignment. increase tire wear
Improper alignment will and lower fuel economy.
쐌 Air
conditioner
fuel economy. Use the air conditioner only when necessary.
operation
lowers
5-18 Starting and driving
쐌 When cruising at highway speeds, it is more economical to use the air conditioner and
墌 07.7.25/Z33-D/V5.0 墍
PARKING/PARKING ON HILLS
leave the windows closed to reduce drag.
쐌 Use the recommended viscosity engine oil. See “Engine oil and oil filter recommenda- tion” in the “9. Technical and consumer infor- mation” section.
WARNING
1. Firmly apply the parking brake. 2. Automatic transmission models:
MSD0002
쐌 Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
쐌 Never leave the engine running while
the vehicle is unattended.
쐌 Do not leave children unattended in-
side the vehicle.
Move the selector lever to the P (Park) posi- tion. Manual transmission models: Place the shift lever in the R (Reverse) posi- tion. When parking on an uphill grade, place the shift lever in the 1 (Low gear) position.
Starting and driving 5-19
墌 07.7.25/Z33-D/V5.0 墍
쐌 HEADED UPHILL WITH CURB: 쎻2
Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.
쐌 HEADED UPHILL OR DOWNHILL, NO
CURB: 쎻3
Turn the wheels toward the side of the road
so the vehicle will move away from the center
of the road if it moves.
4. Turn the ignition key to the LOCK position
and remove the key.
POWER STEERING
WARNING
If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate.
The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns or at low speeds.
WARNING
쐌 Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for automatic transmission models or in an appropriate gear for manual transmission models. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident.
쐌 Make sure the automatic transmis- sion selector lever has been pushed as far forward as it can go and cannot be moved without depressing the button at the end of the lever.
3. To help prevent the vehicle from rolling into the street when parked on a sloping drive way, it is a good practice to turn the wheels as illustrated.
쐌 HEADED DOWNHILL WITH CURB: 쎻1
Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.
5-20 Starting and driving
墌 07.7.25/Z33-D/V5.0 墍
BRAKE SYSTEM
BRAKING PRECAUTIONS The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and the stopping distance will be longer. Using the brakes Avoid resting your foot on the brake pedal while driving. This overheats the brakes, increases wear on the brakes and pads, and reduces gas mileage. To help save the brakes and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control.
WARNING
쐌 While driving on a slippery surface, be careful when braking, accelerat- ing or downshifting. Abrupt braking or accelerating could cause the wheels to skid and result in an acci- dent.
쐌 If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder.
Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking. To dry brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat-up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. Parking brake break-in Break in the parking brake shoes whenever the
stopping effect of the parking brake is weakened or whenever the parking brake shoes and/or drums/rotors are replaced, in order to assure the best braking performance.
This procedure is described in the vehicle ser- vice manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS)
WARNING
쐌 The Anti-lock Braking System (ABS) is a sophisticated device, but it can- not prevent accidents resulting from careless or dangerous driving tech- niques. It can help maintain vehicle control during braking on slippery surfaces. Remember that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS. Stopping distances may also be longer on rough, gravel or snow covered roads, or if you are using tire chains. Always maintain a safe distance from the vehicle in
Starting and driving 5-21
墌 07.7.25/Z33-D/V5.0 墍
front of you. Ultimately, the driver is responsible for safety.
쐌 Tire type and condition may also af-
fect braking effectiveness.
— When replacing tires,
the specified size of tires on all four wheels.
install
— When installing a spare tire, make sure that it is the proper size and type as specified on the Tire and Loading Information label. See “Tire and Loading Information label” in the “9. Technical and consumer informa- tion” section of this manual.
— For
detailed
information,
see “Wheels and tires” in the “8. Mainte- nance and do-it-yourself” section of this manual.
The Anti-lock Braking System (ABS) controls the brakes so the wheels do not lock during hard braking or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding. By preventing each wheel from locking, the system 5-22 Starting and driving
ABS warning light on the instrument panel. The brake system then operates normally, but with- out anti-lock assistance. If the ABS warning light illuminates during the self-test or while driving, have the vehicle checked by a NISSAN dealer. Normal operation The ABS operates at speeds above 3 to 6 MPH (5 to 10 km/h). The speed varies according to road conditions. When the ABS senses that one or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating. This is normal and indicates that the ABS is operating properly. However, the pulsa- tion may indicate that road conditions are haz- ardous and extra care is required while driving.
helps the driver maintain steering control and helps to minimize swerving and spinning on slippery surfaces. Using the system Depress the brake pedal and hold it down. Depress the brake pedal with firm steady pres- sure, but do not pump the brakes. The ABS will operate to prevent the wheels from locking up. Steer the vehicle to avoid obstacles.
WARNING
Do not pump the brake pedal. Doing so may result in increased stopping dis- tances.
Self-test feature The ABS includes electronic sensors, electric pumps, hydraulic solenoids and a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a “clunk” noise and/or feel a pulsation in the brake pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunc- tion, it switches the ABS off and illuminates the
墌 07.7.25/Z33-D/V5.0 墍
WARNING
The traction control system is designed to prevent the wheels from spinning. However, it does not prevent vehicle slipping or spinning due to abrupt steer- ing operation at high speeds or by care- less or dangerous driving techniques. Be especially careful when driving on slippery surfaces and always drive safely.
TRACTION CONTROL SYSTEM (TCS) (if so equipped) On slippery surfaces such as wet asphalt roads, vehicle wheels may spin when the vehicle is accelerated. This wheel spin reduces accelera- tion, or causes the vehicle to swerve, thus decreasing vehicle stability.
When the vehicle drive wheels begin to spin, the Traction Control System (TCS) controls the engine torque using an electronic control sys- tem, and it also controls automatic control shift- ing if necessary (for automatic transmission models). This reduces spinning of the drive wheels, and result in improved vehicle accelera- tion performance. It also improves the vehicle stability by swerving motion. 쐌 When the TCS is operating, the “SLIP” indi-
cator light in the meter panel blinks.
쐌 If the “SLIP” indicator light blinks, the vehicle is under slippery conditions. Be sure to drive carefully. See “Slip indicator light” and “Trac- tion Control System (TCS) off indicator light” in the “2. Instruments and controls” section.
쐌 Indicator light
If a malfunction occurs in the TCS, the “SLIP” and “TCS OFF” indicator lights come on in the instrument panel. As long as these indi- cator lights are illuminated, the traction con- trol function (except the ABS) is canceled. The vehicle will behaves like a model without the TCS.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM (if so equipped) When accelerating or driving on slippery sur- faces, the tires may spin or slide. With the Vehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle sta- bility. 쐌 When the VDC system is operating,
the in the instrument panel
“SLIP” blinks.
indicator
쐌 If the “SLIP” indicator blinks, the road condi- tions are slippery. Be sure to adjust your speed and driving to these conditions. Be sure to drive carefully. See “Slip indicator light”, and “Vehicle Dynamic Control (VDC) OFF indicator light” in the “2. Instruments and controls” section.
쐌 Indicator light
If a malfunction occurs in the system, the “SLIP” and “VDC OFF” indicator lights illumi- nate in the instrument panel. As long as these indicators are illuminated, the VDC system function is canceled.
The VDC system uses an Active Brake Limited
Slip (ABLS) system to improve vehicle traction.
The ABLS system works when one of the driving
wheels is spinning on a slippery surface. The
ABLS system brakes the spinning wheel, which
distributes the driving power to the other driving
wheel. If the vehicle is operated with the VDC
Starting and driving 5-23
墌 07.7.25/Z33-D/V5.0 墍
system turned off, all VDC system functions will be turned off. The ABLS system and ABS will still operate with the VDC system off. When the ABLS system is activated, the “SLIP” indicator light will blink and you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.
While the VDC system is operating, you may feel a pulsation in the brake pedal and hear a noise or feel a vibration from under the hood. This is normal and indicates that the VDC system is working properly.
The VDC system computer has a built-in diag- nostic feature that tests the system each time you start the engine and move the vehicle at a low speed forward or backward. When the self-test occurs, you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.
WARNING
쐌 The VDC system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or due to careless or dangerous driving
5-24 Starting and driving
techniques. Reduce vehicle speed and be especially careful when driv- ing and cornering on slippery sur- faces and always drive carefully.
쐌 Do not modify the vehicle’s suspen- sion. If suspension parts such as shock absorbers, struts, springs, sta- bilizer bars and bushings and wheels are not NISSAN-approved or are ex- tremely deteriorated the VDC system may not operate properly. This could adversely affect vehicle handling per- formance, and the “VDC OFF” indica- tor or “SLIP” indicator or both indica- tor lights may illuminate.
쐌 If brake related parts such as brake pads, rotors and calipers are not standard equipment or are extremely deteriorated, the “VDC OFF” indica- tor or “SLIP” indicator or both indica- tor lights may illuminate.
쐌 If engine related parts such as a muf- fler are not standard equipment or are extremely deteriorated, the “VDC OFF” indicator or “SLIP” indicator or
both indicator lights may illuminate. 쐌 When driving on extremely inclined surfaces such as higher banked cor- ners, the VDC system may not oper- ate properly and the “VDC OFF” indi- cator or “SLIP” indicator or both indicator lights may illuminate. Do not drive on these types of roads.
쐌 When driving on an unstable surface such as a turntable, ferry, elevator or ramp, the “VDC OFF” indicator or “SLIP” indicator or both indicator lights may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface.
쐌 If wheels or tires other than those recommended are used, the VDC sys- tem may not operate properly and the “VDC OFF” indicator or “SLIP” indi- cator or both indicator lights may illuminate.
쐌 The VDC system is not a substitute for winter tires or tire chains on a snow-covered road.
墌 07.7.25/Z33-D/V5.0 墍
COLD WEATHER DRIVING
FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply deicer or glycerin to it through the key hole. If the lock becomes frozen, heat the key before insert- ing it into the key hole. ANTI-FREEZE In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check anti-freeze to assure proper winter protection. For additional information, see “Engine Cooling System” in the “8. Maintenance and do-it- yourself” section. BATTERY If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain the battery should be maximum efficiency, checked regularly. For additional information, see “Battery” in the “8. Maintenance and do-it- yourself” section. DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system by opening the drain plug located under the radiator. Refill before operating the vehicle. See “Engine cool- ing system” in the “8. Maintenance and do-it- yourself” section for changing engine coolant.
TIRE EQUIPMENT 1. SUMMER tires are of a tread design to provide superior performance on dry pave- ment. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your vehicle on snowy or icy roads, NISSAN recommends the use of MUD & SNOW or ALL SEASON tires on all four wheels. Consult a NISSAN dealer for the tire type, size, speed rating and availability information.
2. For additional traction on icy roads, studded tires may be used. However, some provinces and states prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of stud- ded snow tires, on wet or dry surfaces, may be poorer than that of non-studded snow tires.
3. Tire chains may be used. For details, see “Tire chains” in the “8. Maintenance and do-it-yourself” section of this manual.
SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: 쐌 a scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.
쐌 a sturdy, flat board to be placed under the
jack to give it firm support.
쐌 a shovel to dig the vehicle out of snow-drifts. 쐌 extra window washer fluid to refill the reser-
voir tank.
DRIVING ON SNOW OR ICE
WARNING
쐌 Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” un- der these conditions. Try to avoid driving on wet ice until the road is salted or sanded.
쐌 Whatever the condition, drive with caution. Accelerate and slow down
Starting and driving 5-25
墌 07.7.25/Z33-D/V5.0 墍
with care. If accelerating or down- shifting too fast, the drive wheels will lose even more traction.
쐌 Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement. 쐌 Allow greater following distances on
slippery roads.
쐌 Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steer- ing maneuvers.
쐌 Do not use cruise control on slippery
roads.
쐌 Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.
ENGINE BLOCK HEATER (if so equipped) Engine block heaters are available through NISSAN dealers to assist in cold temperature starting. The engine block heater should be used when the outside temperature is 20°F (−7°C) or lower. To use the engine block heater: 1. Turn the engine off. 2. Open the hood and unwrap the engine block
heater cord.
3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord. 4. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110-volt AC (VAC) outlet.
5. The engine block heater must be plugged in for at least 2 - 4 hours, depending on outside temperatures, to properly warm the engine coolant. Use an appropriate timer to turn the engine block heater on.
6. Before starting the engine, unplug and prop- erly store the cord to keep it away from moving parts.
WARNING
쐌 Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. You can be seriously injured by an electrical shock if you use an ungrounded con- nection.
쐌 Disconnect and properly store the engine block heater cord before starting the engine. Damage to the cord could result in an electrical shock and can cause serious injury. 쐌 Use a heavy-duty 3-wire, 3-pronged extension cord rated for at least 10 A. Plug the extension cord into a Ground Fault (GFI) pro- tected, grounded 110-VAC outlet. Failure to use the proper extension cord or a grounded outlet can result in a fire or electrical shock and cause serious personal injury.
Interrupt
5-26 Starting and driving
墌 07.7.25/Z33-D/V5.0 墍
MEMO
Starting and driving 5-27
墌 07.7.25/Z33-D/V5.0 墍
MEMO
5-28 Starting and driving
墌 07.7.25/Z33-D/V5.0 墍
6 In case of emergency
Flat tire .................................................................................... 6-2
Tire pressure monitoring system (TPMS) ................. 6-2
Changing a flat tire ......................................................... 6-2
Jump starting ......................................................................... 6-7
Push starting .......................................................................... 6-9
If your vehicle overheats ..................................................... 6-9
Towing your vehicle ........................................................... 6-10
Towing recommended by NISSAN ......................... 6-11
Vehicle recovery (Freeing a stuck vehicle) ............ 6-12
墌 07.7.25/Z33-D/V5.0 墍
FLAT TIRE
TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If the vehicle is being driven with low tire pressure, the TPMS will activate and warn you of it by the low tire pressure warning light (in the meter panel). This system will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). For more details, refer to “Warning/indicator lights and audible reminders” in the “2. Instruments and controls” section and “Tire pressure moni- toring system (TPMS)” in the “5. Starting and driving” section.
WARNING
쐌 If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as pos- sible. Driving with under-inflated tires may permanently damage the
6-2 In case of emergency
tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an acci- dent and could result in serious per- sonal injury. Check the tire pressure for all four tires. Adjust the tire pres- sure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible.
쐌 When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the TPMS.
the proper operation of
쐌 Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pres- sure sensors.
CHANGING A FLAT TIRE If you have a flat tire, below. Stopping the vehicle 1. Safely move the vehicle off the road away
follow the instructions
from traffic.
2. Turn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake. Shift the manual transmission into R (Reverse) position (automatic transmission in P (Park) position).
4. Turn off the engine. 5. Raise the hood to warn other traffic, and to signal professional road assistance person- nel that you need assistance.
6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.
墌 07.7.25/Z33-D/V5.0 墍
WARNING
쐌 Make sure the parking brake is se- curely applied and the manual trans- mission is shifted into R (Reverse), or the automatic transmission into P (Park).
쐌 Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.
쐌 Never change tires if oncoming traffic is close to your vehicle. Wait for pro- fessional road assistance.
MCE0001A
SCE0409
Blocking wheels Place suitable blocks 쎻1 at both the front and back of the wheel diagonally opposite the flat tire to prevent the vehicle from moving when it
is jacked up.
WARNING
Coupe models
Getting the spare tire and tools Remove jacking tools and spare tire from the storage area located in the luggage/trunk as illustrated. Coupe models: 1. Spare tire — Turn the retainer counterclock-
wise to remove.
Be sure to block the wheel as the ve- hicle may move and result in personal injury.
2. Jack — Turn it counterclockwise to remove. 3. Jacking tools
In case of emergency 6-3
墌 07.7.25/Z33-D/V5.0 墍
the vehicle to move. This is especially true for vehicles with limited slip dif- ferentials.
쐌 Do not allow passengers to stay in
the vehicle while it is on the jack.
Carefully read the caution label attached to the jack body and the following instruc- tions.
Jacking up the vehicle and removing the damaged tire
WARNING
쐌 Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands.
쐌 Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is de- signed for lifting only your vehicle during a tire change.
쐌 Use the correct jack up points. Never use any other part of the vehicle for jack support.
쐌 Never jack up the vehicle more than
necessary.
쐌 Never use blocks on or under the
jack.
쐌 Do not start or run the engine while vehicle is on the jack, as it may cause
墌 07.7.25/Z33-D/V5.0 墍
SCE0491
Roadster models
Roadster models: 1. Spare tire — Turn the retainer counterclock-
wise to remove.
2. Jack — Unfasten the belt and lift the jack up
to remove.
3. Jacking tools — They are in the tool bag.
6-4 In case of emergency
SCE0410A
Jack-up point
1. Place the jack directly under the jack-up point as illustrated above so that top of the jack contacts the vehicle at the jack up point. Align the jack head between the two notches in the front or the rear as shown. Also fit the groove of the jack head between the notches as shown.
The jack should be used on level firm ground. 2. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.
3. Carefully raise the vehicle until the tire clears the ground. To lift the vehicle, securely hold the jack lever and rod with both hands as shown above. Remove the wheel nuts, and then remove the tire.
CE1092-A
In case of emergency 6-5
墌 07.7.25/Z33-D/V5.0 墍
nuts alternately and evenly in the sequence illustrated (쎻1 - 쎻5 ) until they are tight.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the se- quence as illustrated. Lower the vehicle com- pletely.
WARNING
쐌 Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.
쐌 Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.
쐌 Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).
As soon as possible tighten the wheel nuts to the specified torque with a torque wrench.
SCE0039
Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading “Wheels and tires” in the “8. Main- tenance and do-it-yourself” section.
1. Clean any mud or dirt
from the surface
between the wheel and hub.
2. Carefully put the wheel on and tighten the wheel nuts finger tight. When replacing a front tire, make sure the hole in the spare tire wheel is aligned with the pin on the brake rotor.
3. With the wheel nut wrench, tighten wheel 6-6 In case of emergency
Wheel nut tightening torque:
80 ft-lb (108 N⋅m)
The wheel nuts must be kept tightened to specification at all is recom- mended that wheel nuts be tightened to specification at each lubrication interval.
times.
It
Adjust tire pressure to the COLD pressure.
COLD pressure:
After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km).
COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver’s side center pillar. Stowing the damaged tire and tools Securely store the spare tire and jacking equip- ment in the vehicle.
WARNING
쐌 Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an
墌 07.7.25/Z33-D/V5.0 墍
accident or sudden stop.
쐌 The spare tire is designed for emer- gency use. See specific instructions under the heading “Wheels and tires” in the “8. Maintenance and do-it- yourself” section of this manual.
12 volts. Use of an improperly rated battery can damage your vehicle.
쐌 Whenever working on or near a bat- tery, always wear suitable eye protec- tors (for example, goggles or indus- trial safety spectacles) and remove rings, metal bands, or any other jew- elry. Do not lean over the battery when jump starting.
쐌 Do not attempt to jump start a frozen battery. It could explode and cause serious injury.
JUMP STARTING
To start your engine with a booster battery, the instructions and precautions below must be followed.
WARNING
쐌 If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.
쐌 Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.
쐌 Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a corrosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with any- thing, immediately flush the con- tacted area with water.
쐌 Keep battery out of the reach of chil-
dren.
쐌 The booster battery must be rated at
In case of emergency 6-7
墌 07.7.25/Z33-D/V5.0 墍
CAUTION
쐌 Always connect positive (+) to posi- tive (+) and negative (−) to body ground (for example, strut mounting bolt, etc. — not to the battery).
쐌 Make sure that the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal.
5. Start the engine of the other vehicle and let it
run for a few minutes.
6. Keep the engine speed of the other vehicle at about 2,000 rpm, and start your engine in the normal manner.
CAUTION
Do not keep the starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.
SCE0664
to the P (Park) position (automatic transmis- sion models) or move the shift lever to the N (Neutral) position (manual transmission mod- els). Switch off all unnecessary electrical systems (light, heater, air conditioner, etc.).
3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.
4. Connect jumper cables in the sequence as
illustrated. (쎻1 - 쎻4 )
WARNING
Always follow the instructions below. Failure to do so could result in damage to the charging system and cause per- sonal injury.
1.
If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries into close proximity to each other. Do not allow the two vehicles to touch. 2. Apply parking brake. Move the selector lever 6-8 In case of emergency
墌 07.7.25/Z33-D/V5.0 墍
PUSH STARTING
IF YOUR VEHICLE OVERHEATS
7. After starting your engine, carefully discon- nect the negative cable and then the positive cable.
8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.
Do not attempt to start the engine by pushing.
CAUTION
쐌 Automatic transmission models can- not be push started. Attempting to do so may cause transmission damage. 쐌 Three-way catalyst equipped models should not be started by pushing since the three-way catalyst may be damaged.
쐌 Never try to start the vehicle by tow- ing it; when the engine starts, the forward surge could cause the ve- hicle to collide with the tow vehicle.
WARNING
쐌 Do not continue to drive if your ve- hicle overheats. Doing so could cause engine damage or a vehicle fire.
쐌 To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the ra- diator cap is removed, pressurized hot water will spurt out, possibly causing serious injury.
쐌 Do not open the hood if steam is
coming out.
If your vehicle is overheating (indicated by an extremely high temperature gauge reading), or if you feel a lack of engine power, detect abnormal noise, etc., take the following steps:
1. Move the vehicle safely off the road, apply the parking brake and move the shift lever to the N (Neutral) position (automatic transmission to the P (Park) position). Do not stop the engine.
2. Turn off the air conditioner. Open all the
In case of emergency 6-9
墌 07.7.25/Z33-D/V5.0 墍
3.
windows, and move the temperature control to maximum hot and the fan control to high speed. If engine overheating is caused by climbing a long hill on a hot day, run the engine at a fast idle (approximately 1,500 rpm) until the tem- perature gauge indication returns to normal. 4. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen.
5. Open the engine hood.
WARNING
If steam or water is coming from the engine, stand clear to prevent getting burned.
6. Visually check if the cooling fan is running. The radiator hoses and radiator should not leak water. If coolant is leaking or the cooling fan does not run, stop the engine.
6-10 In case of emergency
WARNING
쐌 Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or get caught in, engine belts or the engine cooling fan.
쐌 The engine cooling fan can start at any time when the coolant tempera- ture is high.
7. After the engine cools down, check the cool- ant level in the reservoir tank with the engine running. Add coolant to the reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer.
TOWING YOUR VEHICLE
When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from a NISSAN dealer. Local service operators are generally familiar with the appli- cable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions.
WARNING
쐌 Never ride in a vehicle that is being
towed.
쐌 Never get under your vehicle after it
has been lifted by a tow truck.
CAUTION
쐌 When towing, make sure that the transmission, axles, steering system and powertrain are in working condi-
墌 07.7.25/Z33-D/V5.0 墍
tion. If any unit is damaged, dollies must be used.
쐌 Always attach safety chains before
towing.
For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “9. Technical and consumer information” section of this manual.
SCE0342
SCE0489
TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
CAUTION
쐌 Never tow automatic transmission models with the rear wheels on the
In case of emergency 6-11
墌 07.7.25/Z33-D/V5.0 墍
ground or four wheels on the ground (forward or backward) as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the front wheels raised, always use towing dollies under the rear wheels.
쐌 When towing rear wheel drive mod- els with the front wheels on the ground or on towing dollies:
Turn the ignition key to the OFF po- sition, and secure the steering wheel in a straight ahead position with a rope or similar device. Never secure the steering wheel by turning the ignition key to the LOCK position. This may damage the steering lock mechanism.
6-12 In case of emergency
WARNING
쐌 Stand clear of a stuck vehicle. 쐌 Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.
CAUTION
쐌 Tow chains or cables must be at- tached only to the main structural members of the vehicle or the recov- ery hook. Otherwise, the vehicle body will be damaged.
쐌 Do not use the vehicle tie down hooks to free a vehicle stuck in sand, snow, mud, etc. Never tow a vehicle using the vehicle tie down hooks.
쐌 Always pull the cable straight out from the front of the vehicle. Never pull on the vehicle at an angle.
SCE0605
VEHICLE RECOVERY (Freeing a stuck vehicle) Use the recovery hook by installing it in the front of the vehicle. (The rear has no towing points.)
1. Remove the front
license plate (if so
equipped).
2. Remove the recovery hook cover 쎻1 from the
bumper.
3. Securely install the recovery hook 쎻2 stored
with jacking tools.
Make sure that the hook is properly secured in the stored place after use.
墌 07.7.25/Z33-D/V5.0 墍
쐌 Release the accelerator pedal before shifting between R and D (automatic transmission models) or 1st and R (manual transmission models).
쐌 Do not spin the tires above 35 MPH (55
km/h). If the vehicle cannot be freed after a few tries, contact a professional towing service to re- move the vehicle.
5.
쐌 Pulling devices should be routed so they do not touch any part of the suspension, steering, brake or cool- ing systems.
쐌 Pull devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.
If your vehicle is stuck in sand, snow, mud, etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control (VDC) system or Traction Control System (TCS) (if so equipped).
2. Make sure the area in front and behind the
vehicle is clear of obstructions.
3. Turn the steering wheel right and left to clear
an area around the front tires.
4. Slowly rock the vehicle forward and back-
ward.
쐌 Shift back and forth between R (reverse) and D (drive) (automatic transmission models) or 1st (low) and R (reverse) (manual transmis- sion models).
쐌 Apply the accelerator as little as possible to
maintain the rocking motion.
In case of emergency 6-13
墌 07.7.25/Z33-D/V5.0 墍
MEMO
6-14 In case of emergency
墌 07.7.25/Z33-D/V5.0 墍
7 Appearance and care
Cleaning exterior ................................................................... 7-2
Washing ............................................................................ 7-2
Waxing ............................................................................... 7-3
Removing spots .............................................................. 7-3
Underbody ........................................................................ 7-3
Glass .................................................................................. 7-3
Aluminum alloy wheels .................................................. 7-4
Chrome parts ................................................................... 7-4
Tire dressing .................................................................... 7-4
Cleaning interior .................................................................... 7-5
Floor mats ......................................................................... 7-5
Seat belts ......................................................................... 7-6
Corrosion protection ............................................................ 7-6
Most common factors contributing to vehicle
corrosion ........................................................................... 7-6
Environmental factors influence the rate of
corrosion ........................................................................... 7-6
To protect your vehicle from corrosion ..................... 7-6
墌 07.7.25/Z33-D/V5.0 墍
CLEANING EXTERIOR
In order to maintain the appearance of your vehicle, it is important to take proper care of it.
In the following cases, please wash your vehicle as soon as possible to protect the paint surface. 쐌 After a rainfall to prevent possible damage
from acid rain
쐌 After driving on coastal roads 쐌 When contaminants such as soot, bird drop- pings, tree sap, metal particles or bugs get on the paint surface
쐌 When dust or mud builds up on the surface Whenever possible, store or park your vehicle inside a garage or in a covered area.
When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off the vehicle with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or a general purpose dish-washing liquid mixed with clean, lukewarm (never hot) water. 7-2 Appearance and care
CAUTION
쐌 Do not use car washes that use acid in the detergent. Some car washes, especially brushless ones, use some acid for cleaning. The acid may react with some plastic vehicle compo- nents, causing them to crack. This could affect their appearance, and also could cause them not to function properly. Always check with your car wash to confirm that acid is not used. 쐌 Do not use strong household soap, strong chemical detergents, gasoline or solvents.
쐌 Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted.
쐌 Avoid using tight-napped or rough cloths, such as washing mitts. Care must be taken when removing caked-on dirt or other foreign sub- stances so the paint surface is not scratched or damaged.
쐌 For Roadster models, observe the
following: • Do not use an automatic car wash or a high pressure car wash. The soft top may be damaged.
• Avoid applying direct water pres- sure, such as high pressured water from household hoses, on the lin- ing of the soft top and vehicle body. Avoid applying continuous water on the parts around the soft top and the windows. These may cause water to leak into the inside of your vehicle.
Rinse the vehicle again with plenty of clean water.
Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. Therefore, these areas must be regularly cleaned. Make sure that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. Avoid leaving water spots on the paint surface by using a damp chamois to dry the vehicle.
墌 07.7.25/Z33-D/V5.0 墍
Soft top care and cleaning (Roadster models) Proper care and handling should be observed to maintain a good appearance of the soft top. Improper care may cause the top cloth’s surface to stiffen, stain, or mat. Follow the instructions shown in this section.
It is not necessary to wash the soft top every time you wash the vehicle body, but clean the top regularly before it becomes quite dirty. Leav- ing the soft top dirty or soiled for a long period will cause deterioration to the quality of the top material. Remove dust or dirt on the soft top with a soft brush or sponge, then rinse it with plenty of clean water. When the top is quite dirty, wash using a mild detergent, such as a general cleaner especially made for a cloth top or a general purpose dish-washing liquid, mixed with clean, lukewarm (never hot) water. Rinse the top again with plenty of clean water to remove all traces of soap.
CAUTION
쐌 Do not use strong household soap, strong chemical detergents, gasoline
or solvents.
쐌 If glass cleaner gets on the soft top, immediately wash it off with clean water.
쐌 Do not apply direct water pressure, such as high pressured water from household hoses, on the lining of the soft top and vehicle body, as this may cause water to leak into the inside of your vehicle.
After cleaning, always be sure the top and its storage are completely dry before opening the top. Opening the top while it is wet or damp may cause interior water damage, water stains or mildew on the top. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. Polishing is recommended to remove built-up wax residue and to avoid a weathered appearance before reapplying wax. A NISSAN dealer can assist you in choosing the proper product. 쐌 Wax your vehicle only after a thorough wash-
ing. Follow the instructions supplied with the wax.
쐌 Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.
Machine compounding or aggressive polishing
on a base coat/clear coat paint finish may dull
the finish or leave swirl marks.
REMOVING SPOTS
Remove tar and oil spots, industrial dust, insects,
and tree sap as quickly as possible from the
surface of the paint to avoid lasting damage or
staining. Special cleaning products are available
at a NISSAN dealer or any automotive accessory
store.
UNDERBODY
In areas where road salt is used in winter, the
underbody must be cleaned regularly. This will
prevent dirt and salt from building up and caus-
ing underbody and suspension corrosion. Be-
fore the winter period and again in the spring, the
underseal must be checked and, if necessary,
re-treated.
GLASS
Use glass cleaner to remove smoke and dust film
from the glass surfaces. It is normal for glass to
Appearance and care 7-3
墌 07.7.25/Z33-D/V5.0 墍
If you choose to use a tire dressing, take the following precautions: 쐌 Use a water-based tire dressing. The coating on the tire dissolves more easily with an oil-based tire dressing.
쐌 Apply a light coat of tire dressing to help prevent it from entering the tire tread/grooves (where it would be difficult to remove).
쐌 Wipe off excess tire dressing using a dry towel. Make sure the tire dressing is com- pletely removed from the tire tread/grooves. 쐌 Allow the tire dressing to dry as recom-
mended by tire dressing manufacturer.
become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.
CAUTION
쐌 When cleaning the inside of the win- dows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors or rear window defroster elements.
쐌 If glass cleaner gets on the soft top, immediately wash it off with clean water. (Roadster models)
ALUMINUM ALLOY WHEELS Wash regularly with a sponge dampened in a mild soap solution, especially during winter months in areas where road salt is used. Salt could discolor the wheels if not removed.
CAUTION
Follow the directions below to avoid
7-4 Appearance and care
staining or discoloring the wheels: 쐌 Do not use a cleaner that uses strong acid or alkali contents to clean the wheels.
쐌 Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as ambient temperature.
쐌 Rinse the wheel to completely re- move the cleaner within 15 minutes after the cleaner is applied.
CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish. TIRE DRESSING NISSAN does not recommend the use of tire dressings. Tire manufacturers apply a coating to the tires to help reduce discoloration of the rubber. If a tire dressing is applied to the tires, it may react with the coating and form a com- pound. This compound may come off the tire while driving and stain the vehicle paint.
墌 07.7.25/Z33-D/V5.0 墍
CLEANING INTERIOR
Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth damp- ened in mild soap solution, then wipe clean with a dry soft cloth.
Regular care and cleaning is required in order to maintain the appearance of the leather.
Before using any fabric protector, read the