2003 Mercedes-benz M Class Owners Manual

driving).

After 1000 miles (1500 km) you may grad- ually increase vehicle and engine speeds to the permissible maximum.

178

Operation Driving instructions

Drinking and driving

Pedals

Warning!

Warning!

Drinking and driving and/or taking drugs and driving are a very dangerous combina- tion. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgement.

The possibility of a serious or even fatal ac- cident is sharply increased when you drink or take drugs and drive.

Don’t drink or take drugs and drive or allow anyone to drive after drinking or taking drugs.

Keep driver’s foot area clear at all times. Ob- jects stored in this area may impair pedal movement.

Power assistance

Warning!

When the engine is not running, there is no power assistance for the steering system. In this case, it is important to keep in mind that a considerably higher degree of effort is nec- essary to steer the vehicle.

Driving instructions Drive sensibly – save fuel

Fuel consumption, to a great extent, de- pends on driving habits and operating con- ditions. To save fuel you should: 앫 Keep tires at the recommended infla-

tion pressures

앫 Remove unnecessary loads 앫 Allow engine to warm up under low

load use

앫 Avoid frequent acceleration and decel-

eration

앫 Have all maintenance work performed

at regular intervals by an authorized Mercedes-Benz Light Truck Center

Fuel consumption is also increased by driv- ing in cold weather, in stop-and-go traffic, on short trips and in hilly country.

179

Operation Driving instructions

Brakes

Warning!

After driving in heavy rain for some time without applying the brakes or through wa- ter deep enough to wet brake components, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain expected braking ef- fect. Maintain a safe distance from vehicles in front.

180

Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads.

It can also result in the brakes overheating, thereby significantly reducing their effec- tiveness. It may not be possible to stop the vehicle in sufficient time to avoid an acci- dent.

To help prevent brake disk corrosion after driving on wet road surfaces (particularly salted roads), it is advisable to brake the vehicle with considerable force prior to parking. The heat generated serves to dry the brakes. If your brake system is normally only sub- jected to moderate loads, you should occa- sionally test the effectiveness of the brakes by applying above-normal braking pressure at higher speeds. This will also enhance the grip of the brake pads.

Be very careful not to endanger other road users when you apply the brakes. Refer to the description of the Brake Assist System (BAS) (컄 page 73).

If the parking brake is released and the brake warning lamp in the instrument clus- ter stays on and there is no audible warn- ing (EBP), the brake fluid level in the reservoir is too low. Brake pad wear or a leak in the system may be the reason for low brake fluid in the res- ervoir. Have the brake system inspected at an authorized Mercedes-Benz Light Truck Center immediately. All checks and service work on the brake system should be carried out by an autho- rized Mercedes-Benz Light Truck Center.

Install only brake pads and brake fluid rec- ommended by Mercedes-Benz.

Warning!

If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired. This could result in an accident.

When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces brake pad wear.

After hard braking, it is advisable to drive on for some time, rather than immediately parking, so the air stream will cool down the brakes faster.

Operation Driving instructions

Driving off

Apply the brakes to test them briefly after driving off. Perform this procedure only when the road is clear of other traffic. Warm up the engine smoothly. Do not place full load on the engine until the oper- ating temperature has been reached. When starting off on a slippery surface, do not allow one drive wheel to spin for an ex- tended period with the ESP switched off. Doing so may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

181

Operation Driving instructions

Parking

Set the parking brake whenever park- ing or leaving the vehicle. In addition, move selector lever to position P. In addition, when parking on hills, turn front wheel towards the curb.

182

Tires

Warning!

Do not park this vehicle in areas where com- bustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

To reduce the risk of personal injury as a re- sult of vehicle movement, before turning off the engine and leaving the vehicle always: 앫 Keep right foot on brake pedal. 앫 Firmly depress parking brake pedal. 앫 Move the selector lever to position P. 앫 Slowly release brake pedal. 앫 When parked on an incline, turn front

wheel towards the road curb.

앫 Turn the key to steering lock position 0

and remove.

앫 Take the key and lock vehicle when leav-

ing.

Warning!

If you feel a sudden significant vibration or ride disturbance, or you suspect that possi- ble damage to your vehicle has occurred, you should turn on the hazard warning flash- ers, carefully slow down, and drive with cau- tion to an area which is a safe distance from the road.

Inspect the tires and the vehicle underbody for possible damage. If the vehicle or tires appear unsafe, have it towed to the nearest Mercedes-Benz Light Truck Center or tire dealer for repairs.

Tread wear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and be- come visible at a tread depth of approxi- mately 1/16 in (1.5 mm), at which point the tire is considered worn and should be replaced.

The tread wear indicator appears as a solid band across the tread.

Warning!

Warning!

Do not allow your tires to wear down too far. As tread depth approaches 1/16 in (1.5 mm), the adhesion properties on a wet road are sharply reduced.

Depending upon the weather and/or road surface (conditions), the tire traction varies widely.

Specified tire pressures must be main- tained. This applies particularly if the tires are subjected to high loads (e.g. high speeds, heavy loads, high ambient temper- atures).

Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build-up and possibly a fire.

Hydroplaning

Depending on the depth of the water on the road, hydroplaning may occur even at low speeds and with new tires. Reduce ve- hicle speed, avoid track grooves in the road and apply brakes cautiously in the rain.

Tire traction

The safe speed on a wet, snow covered or icy road is always lower than on a dry road.

Operation Driving instructions

You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point.

Warning!

If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution.

Mercedes-Benz recommends M+S rated radial-ply tires for the winter season for all four wheels to insure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance as compared with summer tires. Stopping distance, however, is still considerably greater than when the road is not covered with snow or ice. Exercise appropriate cau- tion.

183

Operation Driving instructions

Tire speed rating

Additional information on winter tires can be found under “Winter tires” (컄 page 213). ML 320, ML 350
Your vehicle is factory equipped with “H”-rated tires, which have a speed rating of 130 mph (210 km/h). ML 500
Your vehicle is factory equipped with “V”-rated tires, which have a speed rating of 150 mph (240 km/h). An electronic speed limiter prevents your vehicle from exceeding the speed rating. ML 55 AMG Your vehicle is factory equipped with “W”-rated tires, which have a speed rating of 168 mph (270 km/h). Despite of the tire speed rating, local speed limits should be obeyed. Use pru- dent driving speeds appropriate to prevail- ing conditions.

184

Warning!

Even when permitted by law, never operate a vehicle at speeds greater than the maxi- mum speed rating of the tires.

Exceeding the maximum speed for which tires are rated can lead to sudden tire fail- ure, causing loss of vehicle control and pos- sibly resulting in an accident and/or serious injury and possible death, for you and for others.

Winter driving instructions

The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move selector lever to position N. Try to keep the vehicle under control by correc- tive steering action.

Information on driving with snow chains (컄 page 214).

Warning!

On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehi- cle control. Your vehicle’s ABS will not pre- vent this type of control loss.

Do not use LOW RANGE mode when driving on ice or packed snow. At speeds below 18 mph (30 km/h) vehicle steering is ad- versely affected by the LOW RANGE ABS (컄 page 72).

Road salts and chemicals can adversely af- fect braking efficiency. Increased pedal force may become necessary to produce the normal brake effect. We therefore recommend depressing the brake pedal periodically when traveling at length on salt-strewn roads.

This can bring road salt impaired braking efficiency back to normal. Be very careful that you carry out these braking maneu- vers without endangering any other road users. If the vehicle is parked after being driven on salt-treated roads, the braking efficien- cy should be tested as soon as possible af- ter driving is resumed while observing the safety rules in the previous paragraph.

Warning!

If the vehicle becomes stuck in snow, make sure that snow is kept clear of the exhaust pipe and from around the vehicle with the engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle in- terior resulting in unconsciousness and death.

To assure sufficient fresh air ventilation, open a window slightly on the side of the ve- hicle not facing the wind.

Operation Driving instructions

Warning!

Standing water

The outside temperature indicator is not de- signed to serve as an ice-warning device and is therefore unsuitable for that purpose. In- dicated temperatures just above the freez- ing point do not guarantee that the road surface is free of ice.

For more information on winter driving (컄 page 213).

Do not drive through flooded areas or water of unknown depth. Before driving through water, determine its depth. It should not be deeper than approxi- mately 20 inches (50 cm). If you must drive through standing wa- ter, drive slowly to prevent water from entering the passenger compartment or the engine compartment. Water in these areas could cause damage to electrical components or wiring of the engine or transmission, or could result in water being ingested by the engine through the air intake causing severe internal engine damage. Any such dam- age is not covered by the Mer- cedes-Benz Limited Warranty.

185

Operation Driving instructions

Off-road driving

Warning!

Drive slowly in unknown terrain. This will make it easier to recognize unexpected ob- stacles and avoid damage to the vehicle.

To help avoid the vehicle rolling over, never turn it around on steep inclines. If the vehi- cle cannot complete the attempted climb, back it down in reverse gear.

Do not drive along the side of a slope (dan- ger of vehicle rollover). The vehicle might otherwise rollover. If in doing so the vehicle begins to show a tendency to roll, immedi- ately steer into a line of gravity (straight up or downhill).

Never let the vehicle roll backwards in idle or when the clutch is disengaged. You may lose control of the vehicle if you use only the service brake.

186

Warning!

Sand, dirt, mud and other material having friction property can cause exceptional wear and tear as well as brake failure.

Have the brakes checked for dirt build-up and cleaned. There is otherwise a risk that full braking power may not be available in an emergency.

Read this chapter carefully before you be- gin off-road travel. Familiarize yourself with the vehicle char- acteristics and gear changing before you attempt any difficult terrain off-road driv- ing. We recommend that you start out with easy off-road travel.

Special driving features for off-road driving The following driving features are available for specific kind of operation: 앫 LOW RANGE mode (컄 page 118) 앫 LOW RANGE – ABS (컄 page 72) 앫 LOW RANGE – 4-ETS (컄 page 74) 앫 LOW RANGE – ESP (컄 page 76)

Off-road driving rules Engage the LOW RANGE mode before driv- ing under off-road conditions (컄 page 118). Fasten items being carried as securely as possible (컄 page 139).

We recommend keeping doors, liftgate, windows, and sliding/pop-up roof* closed whenever driving in off-road mode.

! Observe the following during off-road driving: 앫 Adjust vehicle speed to condition of terrain. The more uneven, rutty and steeper the terrain, the lower the speed should be

앫 Watch out for obstacles, such as

rocks, holes, tree stumps and ruts. 앫 Be especially careful when driving in unknown territory. It may be nec- essary to get out of the vehicle and scout the path you intend to take. 앫 Continuous and speedy driving in sandy soil overcomes the vehicle rolling resistance, and helps to pre- vent the vehicle from sinking into the ground.

Operation Driving instructions

앫 Do not initiate jumps with the vehi-

cle. It interrupts the forward mo- mentum of the vehicle.

앫 Always drive onto slopes with the the engine running and the vehicle in gear.

Vehicle tool kit 앫 Check if the vehicle jack is functional. 앫 In all cases take the vehicle tool kit, a strong tow rope, a shovel and a small plank (to put under the vehicle jack on sandy soil) with you.

Checklist before off-road driving

Driving in steep terrain

Tires 앫 Check the tread depth and maintain specified tire pressure (see tire pres- sure label inside the fuel filler flap).

앫 Check tires for possible damage and

remove foreign objects.

앫 Replace missing valve caps.

Rims 앫 Dented or bent rims can cause tire pressure loss and damage the tire beads. For this reason, check and, if necessary, change rims before driving off-road.

Slope angle 1 25° (ML 320, ML 350, ML 500)

21° (ML 55 AMG)

2 26°(ML 320, ML 350, ML 500)

23° (ML 55 AMG)

187

Driving across a hilltop 앫 Decelerate just ahead of a hilltop (do not select gear range N), to prevent the vehicle from speeding up too much af- ter climbing a hill. Use the momentum of the vehicle to drive across the hilltop. Driving in this manner prevents the ve- hicle from jumping across the hilltop and thus loosing its forward momen- tum.

Operation Driving instructions

앫 Switch to LOW RANGE mode before starting to drive up or down steep in- clines (컄 page 118).

앫 Driving on embankments, slopes and

other steep inclines should only be done straight up or downhill, i.e. in the line of gravity. Maximum vehicle climb- ing ability is a 60% grade.

앫 Do not drive along the side of a slope (danger of vehicle rollover). If in doing so, the vehicle begins to show a ten- dency to roll, immediately steer into a line of gravity (straight up or downhill). 앫 To help avoid the vehicle rolling over, never turn it around on steep inclines. If the vehicle cannot complete the at- tempted climb, back it down in reverse gear.

앫 Utilize the engine’s braking power

when descending a slope, observe the engine speed (do not overrev the en- gine). Apply the service brake as need- ed.

앫 Check the brakes after a lengthy down-

grade drive.

Avoid excessive engine speeds – drive with moderate engine speeds (max. 3000 RPM). Select gear range 2 or 1 on the auto- matic transmission (컄 page 114).

Traction in steep terrain 앫 Be easy on the accelerator and watch

for continuous wheel traction when driving in steep terrain. The 4-ETS helps greatly when starting out on a steep incline when the front wheels have then the tendency to slip due to the weight shifting away the front axle. The 4-ETS recognizes the situation and limits the torque for the front wheels by braking them. Simultaneously the torque for the rear wheels is increased.

188

Driving downhill 앫 Select gear range 1 on the automatic

transmission (컄 page 114).

앫 Drive downhill observing the same rules as driving uphill (컄 page 187).

앫 The special LOW RANGE – ABS setting

allows for precise and brief (cyclical) blocking of the front wheels, permitting them to dig into loose ground. Remember that the front wheels when stopped, slide across a surface, thus loose their ability to steer the vehicle.

Operation Driving instructions

Driving through water

앫 Switch off the exterior lamps as well as

1 20 in (50 cm) 앫 Before driving through water, deter-

mine its depth. It should not be deeper than approximately 20 inches (50 cm).

앫 Switch to LOW RANGE mode before driving through water (컄 page 118).

the climate control.

앫 Enter the water only at a shallow spot.

Never take a running start.

앫 Drive slowly, avoiding a bow wave. 앫 Do not stop vehicle immersed in water,

and do not shut off the engine.

앫 To dry the brakes, apply pressure to the brake pedal several times after leaving the water.

189

앫 Select gear range 1 on the automatic

transmission (컄 page 114).

앫 Check the vehicle clearance before

crossing obstacles.

앫 Cross obstacles (e.g. tree stumps or

big rocks) very slowly by aiming one of the front wheels at the center of the ob- stacle, and repeat same with the rear wheel.

앫 Special attention is needed when you

cross obstacles on a steep incline. The vehicle could slide sideways as a result of its possible slanted position.

Ruts A number of off-road tracks or other by- ways have deep ruts which can cause the undercarriage to come in contact with the ground. 앫 Select gear range 1 on the automatic

transmission (컄 page 114).

앫 Drive next to the ruts rather than

through them if at all possible.

Operation Driving instructions

Crossing obstacles

Obstacles can damage the vehicle undercarriage or suspension compo- nents. If possible use the assistance of a second person. After off-road driving or crossing obsta- cles, inspect vehicle for any damage, especially vehicle undercarriage and suspension components. Failure to do so can adversely affect the vehicle's fu- ture performance, including increased chance of an accident.

190

Operation Driving instructions

Returning from off-road driving

Warning!

If you feel a sudden significant vibration or ride disturbance, or you suspect that possi- ble damage to your vehicle has occurred, you should turn on the hazard warning flash- ers, carefully slow down, and drive with cau- tion to an area which is a safe distance from the roadway.

Inspect the tires and under the vehicle for possible damage. If the vehicle or tires ap- pear unsafe, have it towed to the nearest Mercedes-Benz Light Truck Center or tire dealer for repairs.

Off-road driving increases strain on the ve- hicle. We recommend that you inspect the vehi- cle for possible damage after each off-road trip. Recognizing any damage and a subse- quent timely repair reduces the chance of a possible breakdown or accident later on. Proceed as follows: 앫 Switch off the LOW RANGE mode

(컄 page 118).

앫 Remove excessive dirt from tires,

wheels, wheel housings, and under- body. For instance, after driving in mud, clean the radiator, chassis, engine, brakes, and wheels from extreme dirt using a strong jet of water.

앫 Inspect frame, oil pan, brake hoses, etc., as well as vehicle underbody for possible damage.

앫 Check tires for possible damage, clean all exterior lamps, and conduct a brake test.

앫 Check for brush or branches caught in

the undercarriage. They could increase the possibility of a fire, as well as cut fuel and/or brake lines, puncture rubber bellows of the axles or drive shafts.

앫 After continued operation in mud,

sand, water or other dirty conditions clean the brake discs, wheels, brake pads and check and clean axle joints.

191

Operation Driving instructions

Trailer towing

Warning!

Failure to use proper equipment and driving technique can result in a loss of vehicle con- trol when towing a trailer.

Improper towing or failure to follow the in- structions contained in this guide can result in serious injury. Follow the guidelines be- low carefully to assure safe trailer operation.

Ask your authorized Mercedes-Benz Light Truck Center should you require an explana- tion of information contained in this guide.

Trailer hitches 앫 Only install a trailer hitch receiver ap-

proved for your vehicle. For information on availability and in- stallation, see your authorized Mercedes-Benz Light Truck Center.

앫 The bumpers on your vehicle are not

designed for use with clamp-type hitch- es. Do not attach rental hitches or other bumper-type hitches to them.

앫 To reduce the possibility of damage, re-

move the hitch ball adaptor from the receiver when not in use.

Electrical connections The vehicle is prewired to accept the sev- en-wire harness included in the Mercedes-Benz approved trailer hitch re- ceiver kit. An additional four-pole conversion plug is included in the Mercedes-Benz supplied trailer hitch receiver kit. For further information, see your autho- rized Mercedes-Benz Light Truck Center.

192

Vehicle and trailer weights and ratings Gross Vehicle Weight Rating (GVWR) is the maximum permissible vehicle weight: 6614 lbs. (3000 kg). Gross Vehicle Weight (GVW): Comprises weight of vehicle including fuel, tools, spare wheel, installed accessories, passengers, cargo and trailer tongue. It must never exceed the GVWR. Gross Axle Weight Rating (GAWR) is the maximum permissible axle weight:

front rear

2976 lbs. 3858 lbs

(1350 kg) (1750 kg)

Gross Trailer Weight (GTW) is the maxi- mum permissible trailer weight to be towed: 5000 lbs. (2260 kg) Trailer Tongue Weight Rating (TWR) is the maximum permissible weight on the trailer tongue: 500 lbs. (225 kg) limit for Mercedes-Benz approved hitch receiver

Loading a trailer 앫 When loading a trailer, you should ob- serve that neither the permissible GTW, nor the GVWR are exceeded. Maximum permissible values are listed on the safety compliance certification labels for the vehicle and for the trailer to be towed. The lowest value listed must be select- ed when determining how the vehicle and trailer are loaded.

앫 The tongue weight at the hitch ball

must be added to the GVW to prevent exceeding your Mercedes-Benz tow ve- hicle’s rear GAWR.

We recommend loading the trailer in such a manner that it has a tongue weight (TW) between 10% and 15% of the GTW.

Operation Driving instructions

Checking weights of vehicle and trailer 앫 To assure that the tow vehicle and trail- er are in compliance with the maximum permissible weight limits have the load- ed rig (tow vehicle including driver, pas- sengers and cargo, trailer fully loaded) weighed on a commercial scale.

앫 Check the vehicle’s front and rear

Gross Axle Weight (GAW), the GTW and TW. The values as measured must not be exceeded, according to the weight list- ed under “Vehicle and trailer weight and ratings”.

193

Operation Driving instructions

Attaching a trailer Observe maximum permitted trailer di- mensions (width and length). Most states and all Canadian provinces re- quire 앫 safety chains between your tow vehicle

and the trailer. The chains should be crisscrossed un- der the trailer tongue. They must be at- tached to the hitch receiver, and not to the vehicle’s bumper or axle. Be sure to leave enough slack in the chains to permit turning corners.

앫 a separate brake system at various

trailer weights.

앫 a break-away switch on trailers with a

separate brake system. The switch activates the trailer brakes in the possible event that the trailer might separate from the tow vehicle.

194

Do not connect a trailer brake system (if trailer is so equipped) directly to the vehicle’s hydraulic brake system, as your vehicle is equipped with antilock brakes. If you do, neither the vehicle’s brakes nor the trailer’s brakes will func- tion properly.

The provided vehicle electrical wiring harness for trailer towing has a brake signal wire (color orange) for hook-up to a brake controller. You should consider using a trailer sway control system. For further infor- mation see your authorized Mercedes-Benz Light Truck Center.

Towing a trailer There are many different laws, including speed limit restrictions, having to do with trailer towing. Make sure that your rig will be legal, not only for where you reside, but also for where you will be driving. A good source for this information can be the po- lice or local authorities. Note the following points, when driving with the trailer: 앫 In order to gain skill and an under-

standing of the vehicle’s behavior, you should practice turning, stopping and backing up in an area which is free from traffic.

앫 Before you start driving check the

앫 trailer hitch 앫 break-away switch 앫 safety chains 앫 electrical connections 앫 lighting and tires

Adjust the mirrors to permit unobstructed view beyond rear of trailer. 앫 If the trailer has electric brakes, start your vehicle and trailer moving slowly, and then apply only the trailer brake controller by hand to be sure the brakes are working properly.

앫 Always secure items in the trailer to

prevent load shifts while driving.

앫 When towing a trailer, check occasion- ally to be sure that the load is secure, and that lighting and trailer brakes (if so equipped) are functioning properly. 앫 Take into consideration that when tow- ing a trailer, the handling characteris- tics are different and less stable from those when operating the vehicle with- out a trailer. It is important to avoid sudden maneu- vers.

앫 The vehicle and trailer combination is heavier, and therefore is limited in ac- celeration and climbing ability, and re- quires longer stopping distances. It is more prone to reacting to side wind gusts, and requires more sensitive steering input.

앫 If possible, do not brake abruptly, but rather engage the brake slightly at first to permit the trailer to activate its brake. Then increase the braking force.

If the trailer should begin to sway, re- duce the vehicle’s speed and use the brake controller by hand to straighten out the vehicle and trailer. In no case should you attempt to straighten out the tow vehicle and trail- er by increasing the speed or over- steering and stepping on the brakes.

Operation Driving instructions

앫 If the transmission hunts between

gears on inclines, manually shift to a lower gear (select 4, 3, 2 or 1). A lower gear and reduction of speed re- duces the chance of engine overload- ing and/or overheating.

앫 On very steep inclines, not manageable with selector lever in position 1, switch transfer case to LOW RANGE mode (컄 page 118).

앫 When going down a long hill, shift into a lower gear and use the engine’s brak- ing effect. Avoid riding the brakes, thus overheat- ing the vehicle and trailer brakes.

195

Operation Driving instructions

앫 If the engine coolant rises to an ex-

Parking

Passenger compartment

tremely high temperature (coolant tem- perature needle approaching the red zone) when the air conditioning is on, turn off the air conditioning system. Engine coolant heat can be additionally vented by opening the windows, switching the climate control fan speed to high and setting the temperature control to the maximum hot position.

앫 Extreme care must be exercised since your vehicle with a trailer will require additional passing distance ahead than when driving without a trailer. Because your vehicle and trailer is longer than your vehicle alone, you will also need to go much farther ahead of the passed vehicle before you can re- turn to your lane.

Warning!

Warning!

To reduce the risk of personal injury, or damage to the vehicle powertrain, as a re- sult of vehicle/trailer movement, always: 앫 Keep right foot on brake pedal. 앫 Shift gear selector lever to position N. 앫 Have a second person place wheel

chocks on downhill side of left and right trailer wheels.

앫 Slowly release brake pedal and let vehi-

cle and trailer roll into chocks until stopped.

앫 Firmly depress parking brake pedal. 앫 Move gear selector lever to position P. 앫 When parked on an incline, turn front

wheel towards the road curb.

Always fasten items being carried as secure- ly as possible.

In an accident, during hard braking or sud- den maneuvers, loose items will be thrown around inside the vehicle, and cause injury to vehicle occupants unless the items are securely fastened in the vehicle.

The trunk is the preferred place to carry ob- jects. Always use partition net when trans- porting cargo. Partition net cannot secure hard or heavy objects.

196

Driving abroad

Abroad, there is a widely-spread Mercedes-Benz service network at your disposal. If you plan to drive into areas which are not listed in the index of your Mercedes-Benz Light Truck Center directo- ry, you should request pertinent informa- tion from your authorized Mercedes-Benz Light Truck Center.

Operation Driving instructions

Control and operation of radio trans- mitters

Telephones and two-way radios

Warning!

MCS, radio and telephone*

Warning!

Do not forget that your primary responsibili- ty is to drive the vehicle. Only operate the MCS, radio or telephone1 if road, weather and traffic conditions permit.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 44 feet (approximately 13.5 m) every sec- ond.

1 Observe all legal requirements.

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. Refer to the radio transmitter operation in- structions regarding use of an external an- tenna.

197

Operation Driving instructions

Catalytic converter

Your Mercedes-Benz is equipped with monolithic type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial con- trol of the pollutants in the exhaust emis- sions. Keep your vehicle in proper operating condition by following our rec- ommended maintenance instructions as outlined in your Service Booklet.

To prevent damage to the catalytic con- verters, use only premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, excessive unburned fuel may reach the catalytic converter, causing it to overheat and start a fire.

198

carried out regularly according to Mercedes-Benz servicing requirements. For details refer to the Service Booklet.

Warning!

Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide, and inhaling it can cause uncon- sciousness and lead to death.

Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one win- dow fully open at all times.

Warning!

As with any vehicle, do not idle, park or op- erate this vehicle in areas where combusti- ble materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Emission control

Certain engine systems serve to keep the toxic components of the exhaust gases within permissible legal limits. These systems, of course, will function properly only when maintained strictly ac- cording to factory specifications. Any ad- justments on the engine should, therefore, be carried out only by qualified Mercedes-Benz Light Truck Center autho- rized technicians. Engine adjustments should not be altered in any way. More- over, the specified service jobs must be

Coolant temperature

During severe operating conditions and stop-and-go city traffic, the coolant tem- perature may rise to approx. 248°F (120°C). The engine should not be operated with the coolant temperature in the red zone. Doing so may cause serious engine dam- age which is not covered by the Mercedes-Benz Limited Warranty.

Warning!

앫 Driving when your engine is badly over-

heated can cause some fluids which may have leaked into the engine com- partment to catch fire. You could be se- riously burned

앫 Steam from an overheated engine can cause serious burns and can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it.

Turn off the engine, get out of the vehicle and do not stand near the vehicle until it cools down.

Operation Driving instructions

199

Operation At the gas station At the gas station

Warning!

Gasoline is highly flammable and poisonous. It burns violently and can cause serious inju- ry. Whenever you are around gasoline, avoid inhaling fumes and skin contact, extinguish all smoking materials. Never allow sparks, flame or smoking materials near gasoline!.

The fuel filler flap is located on the left-hand side of the vehicle towards the rear. Locking/unlocking the vehicle with the remote control automatically locks/unlocks the fuel filler flap.

200

왘 Remove the key from the steering lock. 왘 Open the fuel filler flap 1 by pulling in

direction of the arrow.

왘 Turn the fuel cap 2 to the left and hold

on to it until possible pressure is re- leased.

왘 Take off the cap.

Warning!

Overfilling of the fuel tank may create pres- sure in the system which could cause a gas discharge. This could cause the gas to spray back out when removing the fuel pump noz- zle, which could cause personal injury.

The fuel filler cap is tethered to the fuel filler neck. Do not drop the cap. It could damage the vehicle paint finish.

왘 Replace the fuel cap by turning it to the

right. You will hear when the fuel cap is tight- ened.

왘 Only fill your tank until the filler nozzle unit cut out – do not top up or overfill.

To prevent damaging the lens of the plastic tail lamp, make certain that no gasoline comes into contact with it.

왘 Close the fuel filler flap.

Use only premium unleaded gasoline with a minimum Posted Octane Rating of 91 (average of 96 RON/86 MON). Information on gasoline quality can normally be found on the fuel pump. More information on gasoline can be found in the Factory Approved Service Products pamphlet.

i Leaving the engine running and the fuel cap open can cause the ? lamp to illuminate. See also “Practical hints” section (컄 page 232).

Operation At the gas station

Check regularly and before a long trip

4 Windshield washer and headlamp

왘 Open the hood (컄 page 202)

1 Engine oil level

More information on engine oil can be found in the “Operation” section (컄 page 203). 2 Coolant level

For normal replenishing, use water (po- table water quality). More information on the coolant level can be found in the “Operation” section (컄 page 206).

3 Brake fluid

More information on brake fluid can be found in the “Technical data” section (컄 page 284).

cleaning system More information on filling the reser- voir can be found in the “Operation” section (컄 page 208).

Vehicle lighting Check function and cleanliness. More in- formation on replacing light bulbs can be found in the “Practical hints” section (컄 page 247). Combination switch (컄 page 102).

Tire inflation pressure More information on tire inflation pressure can be found in the “Operation” section (컄 page 211).

201

Operation Engine compartment Engine compartment Hood

Warning!

왘 Pull lever 1 downwards.

왘 Pull up on the hood and then release it.

The hood is unlocked. Handle 2 pro- trudes slightly from the radiator trim. If not, lift the hood slightly.

The hood will be automatically held open at shoulder height by gas-filled struts.

Do not pull the release lever while the vehi- cle is in motion. Otherwise the hood could be forced open by passing air flow.

Opening

To avoid damage to the windshield wip- ers or hood, never open the hood if the wiper arms are folded forward away from the windshield.

Warning!

To help prevent personal injury, stay clear of moving parts when the hood is open and the engine is running. Make sure the hood is properly closed before driving. When closing the hood, use extreme caution not to catch hands or fingers.

The radiator fan may continue to run for ap- proximately 30 seconds or even restart af- ter the engine has been turned off. Stay clear of fan blades.

1 Hood release

202

2 Handle for opening the hood 왘 Pull handle 2 to its stop out of the radi-

ator grill.

Warning!

Closing

If you see flames or smoke coming from the engine compartment, or if the coolant tem- perature gauge indicates that the engine is overheated, do not open the hood. Move away from vehicle and do not open the hood until the engine has cooled. If necessary, call the fire department.

Warning!

The engine is equipped with a transistorized ignition system. Because of the high voltage it is dangerous to touch any components (ig- nition coils, spark plug sockets, diagnostic socket) of the ignition system 앫 with the engine running 앫 while starting the engine 앫 if ignition is “on” and the engine is

turned manually

Warning!

Be careful that you do not close the hood on anyone.

왘 Let the hood drop from a height of ap-

proximately 1 ft (30 cm). The hood will lock audibly.

왘 Check to make sure that the hood is

fully closed. If you can raise the hood at a point above the headlamps, then it is not properly closed. Open it again and let it drop with somewhat greater force.

Do not push the hood closed manually, as this could damage it.

Operation Engine compartment

Engine oil

The amount of oil your engine needs will depend on a number of factors, including driving style. Higher oil consumption can occur when 앫 the vehicle is new 앫 the vehicle is driven frequently at high-

er engine speeds.

Engine oil consumption checks should only be made after the vehicle break-in period.

Checking engine oil level When checking the oil level the vehicle must 앫 be parked on level ground 앫 be at normal operating temperature 앫 have been stationary for at least five

minutes with the engine turned off

203

Operation Engine compartment

Engine oil level display

앫 – 1.0 L

왘 Add 1 liter of engine oil.

앫 – 1.5 L

왘 Add 1.5 liters of engine oil.

앫 – 2.0 L

왘 Add 2 liters of engine oil.

앫 OIL HI

The oil level is too high. 왘 Have excess oil siphoned.

Excessive oil must be siphoned or drained off. It could cause damage to the engine and catalytic converter not covered by the Mercedes-Benz Limited Warranty.

1 Knob 2 Display in speedometer 왘 Switch on the ignition and wait until the

display - - - - - - appears in the speedometer display 2.

왘 Within one second press knob 1 twice. One of the following messages will subse- quently appear in the display: 앫 OIL i.O

The oil level is correct. Engine oil does not to be added.

204

The display - - - - - - flashes in the speedometer display if a proper oil level check cannot be performed. 왘 Repeat the engine oil level check after

a few minutes.

If the engine oil level check cannot be performed again via the display field, use the dipstick to perform the engine oil level check (컄 page 205). In this case we recommend that you have the system checked at a Mercedes-Benz Light Truck Center.

Oil dipstick

1 Oil dipstick 2 Oil filler cap 왘 Remove the oil dipstick 1. 왘 Wipe the oil dipstick clean. 왘 Fully insert dipstick in tube, and re-

move after three seconds.

The engine oil level must be between the lower (min) and upper (max) mark of the dipstick. 왘 Add engine oil if necessary.

Fill quantity between upper and lower dipstick marking, the level is approxi- mately 2.1 US qt (2.0 l).

Operation Engine compartment

Adding engine oil 왘 Unscrew the oil filler cap 2 from the fill- er neck. Be careful not to overfill with oil.

Be careful not to spill any oil when adding. Avoid environmental damage caused by oil entering the ground or water.

Excessive oil must be siphoned or drained off. It could cause damage to the engine and catalytic converter not covered by the Mercedes-Benz Limited Warranty.

왘 Screw the oil filler cap back on the filler

neck.

More information on engine oil can be found in the “Technical data” section (컄 page 286).

205

Operation Engine compartment

Transmission fluid level

The transmission fluid level does not need to be checked. If you notice transmission fluid loss or gear shifting malfunctions, have an authorized Mercedes-Benz Light Truck Center check the automatic trans- mission.

Coolant

The engine coolant is a mixture of water and anticorrosion/antifreeze. To check the coolant level, the vehicle must be parked on level ground and the engine must be cool.

206

Warning!

In order to avoid any possibly serious burns: 앫 Use extreme caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system, or if the coolant temperature gauge indi- cates that the coolant is overheated.

앫 Do not remove pressure cap on coolant reservoir if engine temperature is above 194°F (90°C). Allow engine to cool down before removing cap. The coolant reservoir contains hot fluid and is under pressure.

앫 Using a rag, slowly open the cap approx-

imately ½ turn to relieve excess pres- sure. If opened immediately, scalding hot fluid and steam will be blown out un- der pressure.

앫 Do not spill antifreeze on hot engine

parts. Antifreeze contains ethylene gly- col which may burn if it comes into con- tact with hot engine parts.

1 Cap 2 COLD LEVEL mark The coolant level should reach the COLD LEVEL mark 2 in the reservoir.

If the engine is already at its regular op- erating temperature, the coolant may be approximately 0.6 in (1.5 cm) above the COLD LEVEL mark.

왘 Using a rag, turn the cap slowly approx-

imately one half turn to the left to re- lease any excess pressure.

컄컄

왘 Continue turning the cap to the left and

remove it.

왘 Add coolant as required. 왘 Replace and tighten cap. More information on coolant can be found in the “Technical data” section (컄 page 287).

Battery

The battery is located in the engine com- partment. The battery should always be sufficiently charged in order to achieve its rated ser- vice life. If you use your vehicle mostly for short dis- tance trips, you will need to have the bat- tery charge checked more frequently. When replacing batteries, always use bat- teries approved by Mercedes-Benz.

If you do not intend to operate your vehicle for an extended period of time, consult an authorized Mercedes-Benz Light Truck Center about steps you need to observe.

and precautions when handling automotive batteries.

G Observe all safety instructions A Risk of explosion D Keep flames or sparks away B Battery acid is caustic. Do not

from battery. Do not smoke.

allow it to come into contact with skin, eyes or clothing. In case it does, immediately flush affected area with clear water and seek medical help if necessary.

Operation Engine compartment

E Wear eye protection. C Keep children away. F Follow the instructions in this

Operator's Manual.

Batteries contain materials that can harm the environment if disposed of improperly. Recycling of batteries is the preferred method of disposal. Many states require sellers of batteries to accept old batteries for recycling.

207

! Only use washer fluid which is suitable for plastic lenses. Improper washer flu- id can damage the plastic lenses of the headlamps.

Operation Engine compartment

Windshield washer system and headlamp cleaning system

The windshield washer reservoir is located in the engine compartment.

1 Cap Fluid for the windshield washer system and the headlamp cleaning system* is supplied from the windshield washer reservoir. It has a capacity of 8.0 US qt (7.6 l). During all seasons, add MB Windshield Washer Concentrate “S” to water. Premix the windshield washer fluid in a suitable container.

208

왘 Use the tab to pull cap 1 upwards (ar-

row).

왘 Refill the reservoir with MB Windshield

Washer Concentrate and water (or commercially available premixed wind- shield washer solvent/antifreeze, de- pending on ambient temperatures). Always use washer solvent/antifreeze where temperatures may fall below freezing. Failure to do so could result in damage to the washer system/reser- voir.

Warning!

Washer solvent/antifreeze is highly flamma- ble. Do not spill washer solvent/antifreeze on hot engine parts, because it may ignite. You could be seriously burned.

More information can be found in the “Technical data” section (컄 page 290).

Tires and wheels See your authorized Mercedes-Benz Light Truck Center for information on tested and recommended rims and tires for summer and winter operation. They can also offer advice concerning tire service and pur- chase.

Warning!

Replace rims or tires with the same designa- tion, manufacturer and type as shown on the original part. See your authorized Mercedes-Benz Light Truck Center for fur- ther information. If incorrectly sized rims and tires are mounted: 앫 The wheel brakes or suspension compo-

nents can be damaged

앫 The correct operating clearance of the wheels and the tires are no longer guar- anteed

Warning!

Worn, old tires can cause accidents. If the tire tread is badly worn, or if the tires have sustained damage, replace them.

When replacing rims, use only genuine Mercedes-Benz wheel bolts specified for the particular rim type. Failure to do so can re- sult in the bolts loosening and possibly an accident.

Retread tires are not tested or recom- mended by Mercedes-Benz, since previous damage cannot always be recognized on retreads. Mercedes-Benz can therefore not assure the operating safety of the vehi- cle when such tires are used. See your authorized Mercedes-Benz Light Truck Center for information on tested and recommended rims and tires for summer and winter operation.

Operation Tires and wheels

Important guidelines

앫 Use only sets of tires and rims of the

same type and make.

앫 Tires must be of the correct size for the

rim.

앫 Break in new tires for approximately

60 miles (100 km) at moderate speeds.

앫 Regularly check the tires and rims for

damage.

앫 If vehicle is heavily loaded, check tire

pressure and correct as required.

앫 Do not allow your tires to wear down too far. Adhesion properties on wet roads are sharply reduced at tread depths under 1/8 in (3 mm).

앫 When replacing individual tires, you should mount new tires on the front wheels first.

209

Operation Tires and wheels

When the wheels are heavily soiled, e.g. after driving through mud, clean the inside of the wheels with a jet of water.

210

Life of tire

Direction of rotation

Unidirectional tires offer added advantag- es, such as better hydroplaning perfor- mance. To benefit, however, you must ensure that the tires rotate in the direction specified. An arrow on the sidewall indicates the in- tended direction of rotation of the tire.

The service life of a tire is dependent upon varying factors including but not limited to: 앫 Driving style 앫 Tire pressure 앫 Distance driven

Warning!

Tires and spare tire should be replaced after six years, regardless of the remaining tread.

Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline.

Checking tire inflation pressure

Warning!

If the tire pressure repeatedly drops: 앫 Check the tires for punctures from for-

eign objects

앫 Check to see whether air is leaking from

the valves or from around the rim

Correct the tire pressure only when tires are cold. Regularly check your tire pressure at inter- vals of no more than 14 days. If the tires are warm, you should only cor- rect the tire pressure if it is too low for cur- rent operating conditions. A table on the fuel filler flap lists the spec- ified tire inflation pressures for warm and cold tires as well as for various operating conditions.

The pressures listed for light loads are minimum values offering high driving comfort. Increased inflation pressures listed for heavier loads may also be used for light loads. These higher pressures produce favorable handling characteristics. The ride of the vehicle, however, will be somewhat harder. Never exceed the max. values or inflate tires below the min. values listed in the fuel filler flap.

Tire pressure changes by approximately 1.5 psi (0.1 bar) per 18°F (10°C) of air temperature change. Keep this in mind when checking tire pressure where the temperature is different from the outside temperature. Tire temperature and tire pressure are also increased while driving, depending on the driving speed and the tire load.

Operation Tires and wheels

Warning!

Follow recommended inflation pressures.

Do not overinflate tires. Overinflated tires can result in sudden deflation (blowout) be- cause they are more likely to become punc- tured or damaged by road debris, potholes etc.

Do not underinflate tires. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Do not overload the tires by exceeding the specified vehicle capacity weight (as indicat- ed by the label on the pillar in the driver’s door opening). Overloading the tires can overheat them, possibly causing a blowout.

Check the spare tire periodically for condi- tion and inflation. Spare tire will age and become worn over time even if never used, and thus should be inspected and replaced when necessary.

211

Warning!

Have the tightening torque checked after changing a wheel. Wheels could become loose if not tightened with a torque of 110 ft.lb. (150 Nm).

Use only genuine Mercedes-Benz wheel bolts specified for your vehicle's rims.

Information on changing a wheel can be found in the “Practical hints” section (컄 page 255).

Operation Tires and wheels

Rotating wheels

Warning!

Rotate front and rear wheels only if they are of the same size,

The wheels can be rotated every 3000 to 6000 miles (5000 to 10000 km) or sooner if necessary, according to the degree of tire wear. The same direction of tire rota- tion must be retained. Rotate the wheels before the characteris- tic tire wear pattern becomes visible (shoulder wear on front wheels and tread center wear on rear wheels). Thoroughly clean the inner side of the wheels after each rotation. Check and en- sure proper tire inflation pressure.

212

Winter driving Before the onset of winter, have your vehi- cle winterized at an authorized Mercedes-Benz Light Truck Center. This service includes: 앫 Check of anticorrosion and antifreeze

concentration.

앫 Addition of cleaning concentrate to the water of the windshield and headlamp cleaning system. Add MB Concentrate “S” to a premixed windshield washer solvent/antifreeze which is formulated for below freezing temperatures (컄 page 290).

앫 Battery test. Battery capacity drops

with decreasing ambient temperature. A well charged battery helps to ensure that the engine can be started even at low ambient temperatures.

앫 Tire change. We recommend M+S rat- ed radial-ply tires on all four wheels for the winter season.

Winter tires

Always use winter tires at temperatures below 39°F (4°C) and whenever wintry road conditions prevail. Use of winter tires is the only way to achieve the maximum ef- fectiveness of the ABS, ESP, 4-ETS and EBP in winter operation. For safe handling, ensure that all winter tires mounted are of the same make and have the same tread design.

Warning!

Winter tires with a tread depth under 0.16 in (4 mm) must be replaced. They are no long- er suitable for winter operation.

Operation Winter driving

Always observe the speed rating of the winter tires installed on your vehicle. If the maximum speed for which your tires are rated is below the speed rating of your ve- hicle, you must place a notice to this effect where it will be seen by the driver. Such no- tices are available from your tire dealer or from any authorized Mercedes-Benz Light Truck Center.

Warning!

If you use your spare tire when winter tires are fitted on the other wheels, be aware that the difference in tire characteristics may very well impair turning stability and that overall driving stability may be reduced. Adapt your driving style accordingly.

Have the spare tire replaced with a winter tire at the nearest authorized Mercedes-Benz Light Truck Center.

213

Operation Winter driving

Block heater (Canada only)

Snow chains

The engine is equipped with a block heat- er. The electrical cable may be installed at your authorized Mercedes-Benz Center.

Snow chains should only be driven on snow-covered roads at speeds not to ex- ceed 30 mph (50 km/h). Remove chains as soon as possible when driving on roads without snow.

When driving with snow chains, you may wish to deactivate the ESP (컄 page 76) before setting the vehicle in motion. This will improve the vehicle’s traction.

ML 55 AMG Do not use snow chains with tire size 285/50 R 18.

Observe the following guidelines when us- ing snow chains: 앫 Chains should only be used on all four wheels. With only two chains available, they should be mounted on the rear wheels. Follow the manufacturer’s mounting instructions.

앫 Use only snow chains that are ap-

proved by Mercedes-Benz. Your autho- rized Mercedes-Benz Light Truck Center will be glad to advise you on this subject.

214

Maintenance We strongly recommend that you have your vehicle serviced by your authorized Mercedes-Benz Light Truck Center, in ac- cordance with the Service Booklet at the times called for by the FSS (Flexible Ser- vice System). Failure to have the vehicle maintained in accordance with the Service Booklet at the designated times/mileage called for by the FSS may result in vehicle damage not covered by the Mercedes-Benz Limited Warranty. FSS will notify you when your next service is due.

Operation Maintenance

The interval between services depends on your driving habits. A gentle driving style, moderate engine speeds and the avoidance of short distance trips will lengthen the interval between services.

Clearing the service indicator

The service indicator is automatically cleared after 10 seconds when you switch on the ignition or when reaching the ser- vice threshold while driving. You can also clear it yourself. 왘 Press knob 1.

Service term exceeded

If you have exceeded the suggested ser- vice term: 앫 the 9 or ½ symbol appears in

the display 2 for 30 seconds and a sig- nal sounds after switching on the igni- tion.

앫 it is preceded by a “–” (minus symbol).

215

1 Knob 2 Display in the speedometer Approximately one month before your next service is due, the type of service is indi- cated in the speedometer display 2: 9 Minor service (A) ½ Major service (B) The following information, depending on operating conditions throughout the year, is also shown: 앫 calculated distance remaining 앫 calculated remaining time in days

Operation Maintenance

The Mercedes-Benz Light Truck Center will reset the service indicator following a com- pleted service.

Calling up the service indicator

왘 Within 1 second press knob 1 twice.

The FSS display will appear for ten sec- onds.

216

Resetting the service indicator

In the event that the service on your vehi- cle is not carried out by an authorized Mer- cedes-Benz Light Truck Center, you can reset the service indicator yourself. 왘 Switch ignition on and immediately

press knob 1 twice within one second. The present status for days or distance is displayed.

왘 Within ten seconds turn the key in

steering lock to position 0 (컄 page 33). 왘 Press and hold knob 1 while switching

the ignition on. The present status for days or distance is displayed once more. 왘 Continue to hold knob 1.

After approximately 10 seconds a sig- nal sounds, and the display shows 10 000 miles (Canada: 15 000 km) for approximately 10 seconds.

왘 Release knob 1.

If the service indicator was inadvertent- ly reset, have a Mercedes-Benz Light Truck Center correct it. Only reset if the proper service has been performed. Resetting the system without performing the proper service as called for by the FSS will cause the FSS to incorrectly determine the next service interval which will result in en- gine damage not covered by the Mer- cedes-Benz Limited Warranty. If the battery is disconnected, the days of disconnection will not be included in the count shown by the service indica- tor. To arrive at the true service dead- line, you will need to subtract these days from the days shown in the ser- vice indicator. Do not confuse the service indicator with the engine oil level indicator :.

Operation Vehicle care

Vehicle care Cleaning and care of the vehicle

Warning!